Académique Documents
Professionnel Documents
Culture Documents
HEIDENHAIN
+
E!!!
Users Manual
II/96
General Conditions
for Use
1. By paying the purchase price, the buyer does not acquire the
program, but rather only a temporally unlimited right to use the
program.
2. The buyer is permitted to make copies of the installation
disks only for backup and to copy it to his hard disk. It is
prohibited to sell such copies to a third party. All rights of
possession are retained by the manufacturer.
3. The transfer of the right to use the program to a third party
requires the express written consent of the manufacturer. The
transfer cancels the right of use for the original buyer. All
backup copies must be either given along with the originals or
destroyed without delay, and the manufacturer must also be
informed of this accordingly.
4. The manufacturer is not liable for damages of any kind that
might result from the use of this program.
1 Introduction
Contents
1 Introduction
2 Software
4
Installation
7
7
8
10
13
14
17
17
17
19
21
22
22
22
24
6 Cable Connection
34
35
1 Introduction
1 Introduction
This Users Manual is valid for the software version 08.
The data transfer software delivered on floppy disk includes
four DOS programs. These programs cannot be run under
Windows.
TNC.EXE
TNC.EXE is a program for the transfer of data between the PC
and the following controls: TNC 430/426/425/
415/410/ 4071
406/360/306/355/310/155/151/124/122.
TNC 150.EXE
TNC 150. EXE is a program for the transfer of data between
the PC and the following controls: TNC 150/ 145/ 1351131.
FDE.EXE
FDE.EXE is a program for data transfer between a PC and the
FE 401 floppy disk unit.
FE.EXE
FE.EXE is a program for formatting a 3 l/2 floppy disk on a PC
in FE 401 format and saving NC programs on this disk. These
disks can be read by the FE 401.
258
258
258
258
258
258
258
258
258
510
511
512
513
514
516
517
518
519
08
08
08
08
08
08
08
08
08
German
English
French
Italian
Spanish
Swedish
Danish
Finnish
Dutch
1 Introduction
2 Sofhware Installation
2 Software
Installation
Switch on the PC without the HEIDENHAIN floppy disk in the
disk drive. After the test and switch-on routines your PC then
stands ready with the prompt
C:\>
Insert the HEIDENHAIN disk into drive A.
Set up a directory into which the delivered programs are to be
copied and switch to this directory.
Type and enter the command
COPY A:*.*
the Controls
TNC 151/155
3 Data Transfer
3.2 Starting
with TNCEXE
the Program
You must establish the connection with the TNC before you
begin the program. Then to start the program enter the
following command:
TNC J
The following main menu appears (on condition that the TNC
connection has been established properly and the correct
interface has been selected):
1 File
directory
5 Configuration
,jVersion
N
Ek (GB)
~I:\JH-PCPGM\TNCX<
2 Contents
6End
Current
Display
Define #XMXu
CoMl - COMZ - COMX
COM?: Data bits
COM?: Baud rate
Timeout
Timeout between 2 blocks
Timeout within
one block
Stopwatch
Name verification
Screen image
Printer:
configuration
30 seconds
2 seconds
Not active
Not connected
3.3 Configuration
Here you can select which serial interface you want to use COMI, COM 2 or COMX (if the operating system allows this
choice).
10
inactive"
transfer
"Blockwise
transfer
from PC to TNC"
or
12
13
in-/output
not ready!
Note:
interface
in file
print.
Please
check printer
'X'!
During printout the printer was switched off or paper ran out.
Check the printer.
Printer:
No paper!
The printer was not supplied with paper when you started the
print process. Check the printer.
Printer
off.
Please
check!
The printer was not switched on when you started the print
process. Check the printer.
File
14
name!
The NC program name and the DOS file name do not have
matching characters (see Chapter 7).
File
'XXX'
is write-protected!
not
found
INVALID
15
FILE
PROGRAM INCOMPLETE
There is no end block in the NC program.
CALCULATOR:
FILE
NAME AMBIGUOUS
16
4 Data Transfer
with TNClIO.EXE
the Control
Set the baud rate to 2400. The data format is fixed at 7 data
bits, 1 stop bit and even parity.
4.2 Starting
the program
17
Current
configuration
COM2 - COMX
Screen image
The settings
automatically
automatically
TNCI 50.EXE
18
I
119
Program
transfer
transfer
"Blockwise
transfer
from PC to TNC"
or
20
F3 is without function
F4 Transfer
Returns you to the main menu, from where you can wait for
program transfer.
F5 Configuration
(See section 4.2, Starting and Configuring the Software.)
F6 End
Ends the program and returns you to DOS.
21
5 Program Transfer
PC to FE 401 (FDE.EXE)
Switch off the power to the FE 401 and PC. Connect cable
between the FE 401 and the PC. The RS-232-C cable can be
connected either the PRT or the TNC interface of the FE 401
(see the Operating instructions for the FE 401).
5.2 Starting
FDE.EXE
First switch on the FE 401, then your PC. The prompt C:\>
appears on the PC screen. Change to the directory into which
you copied the program FDE.EXE, then enter the following
command:
FDE J
After the program starts, it asks for the name of the serial
interface through which you wish to transfer the NC programs.
The programs can be transferred via COMI or COM2. Enter
1 or 2 accordingly.
You must then name the path to the directory in which the NC
programs should be stored or from which they are transferred
to the FE 401. Type in the desired path (e.g., c : ).
22
5 Program Transfer
PC to FE 401 (FDE.EXE)
After you have made the settings the function menu appears:
Wersion
4~ (68:
disk unit
+
Calculatar
Calculator
=====bFlexible
disk unit
Program
e n
The data for interface and the path are stored in the
w~~~~~~~.~~~n
file and are shown in the above main menu.
The serial interface COMx can be changed only if this file is
deleted again -for
example with a DOS command.
23
5 Program Transfer
PC to FE 401 (FDE.EXE)
Program directory
of flexible
Load addressed
disk
unit
in drive 0 (upper
can be displayed on
with the Page $ key.
Press the Esc key to
programs
Load all
programs
24
5 Program Transfer
5.3.2 Data Transfer:
PC to FE 401 (FDE.EXE)
Program directory
of calculator
Output
addressed
programs
Output
all
programs
5.3.3 Monitor
'Provide
Functions
data
files
with
write
protection
Remove write
protection
for
data files
Delete
data
files
Show data
files
25
files
from diskette
to diskette
Copies programs from the upper drive to the lower drive of the
FE 401. The diskette in the lower drive must be formatted first
(see Operating Instructions for the FE 401).
Table
of contents
of a diskette
Rename file
"99999967.X"
Program end
Exits the program and returns you to DOS.
26
6 Program
for Formatting
Disks in FE Format
(FE.EXE)
27
Disks in FE Format
(FE.EXE)
The following
screen appears:
HEIOENHRIN
FE 401
Floppy Control
Configuration
Version 4
(GE)
When the program is called for the first time, the 3.5 drive
must be configured to accept a disk formatted for the FE 401.
28
Disks in FE Format
(FEEXE)
screen appears:
HEIIENHAIN
FE 401
Floppy Control
Configuration
Version
(GIlI
l-6666Enter the letter of the drive and press the J key. The
configuration is then stored in the program so that it is always
available for future program calls.
29
Disks in FE Format
(FE.EXE)
screen
HEI[lENHRIN
FE 401
Floppy
Configuration
Control
Version
of the disk
(GB)
drive
30
or press F6 to
FE-4018 U.02
Directory
File Name
Size
Flag
10.H
1.346
101.H
15.223
1657.H
1.323
44444444.H
917
7319.H
4.618
7321.H
4.128
7903.H
2.064
CAD.H
766
DRE1RUND.H
583
FLANSCH.H
8.998
FL8NSCHZ.H
9.372
HEIHA1.H
1.551
ROHRB0G.H 1.821
SP1EGELN.H 5.148
T0RUS.H
702
415.N
5.356
720.896 Byte vacant on data nediun
Directory
File Name
TNCPROG
Size
<directory>
265
123.HNC
99
99999968.HNC
102
99999969.HNC
..
Date
21.04.93
10.03.93
03.03.93
10.03.93
Page J
Page f
31
Disks in FE Format
(FE.EXE)
an FE Floppy Disk
If you are in the FE window (cursor t), you can format the
inserted 3.5 disk in FE 401 format with the F4 key. The new
disk name is formed with FE-401 v and an arbitrary four-digit
disk identification. The progress of formatting is shown in a
window. A disk can also be formatted in the FE 401 floppy disk
unit.
32
6 Program
6.5 Copying
for Formatting
Disks in FE Format
(FE.EXE)
NC Files
All selected files of one window can be copied to the data
medium in the other window. The target window is then
refreshed. The DOS directory shows only files with a name
extension consisting of one character plus NC.
During copying, the DOS name is changed as follows:
XXXXXXXX.HNC -> XXXXXXXX.H
The name is change conversely in the other copying direction.
The file size is different for the same files, because the DOS
file has two characters per line feed and the corresponding FE
file has only one character.
If a file is already present in the target window, the program
will indicated this.
6.6 Deleting
a File
All selected files can be deleted with F3. This applies to files
both in the DOS and in the FE windows.
33
7 Structure
7 Structure
DOS name:
12345678
TEST
ARC12
CUBE7
415 (PLC Program)
407 (Machine parameter list)
12345678.HNC
TESTl.HNC
ARC12.HNC
CUBE7.DNC
415.PNC
407.MNc
for
for
for
for
for
for
for
for
for
For
during program
34
8 Cable Connection
8 Cable Connection
The PC must be connected to the partner unit with the
following signal lines: Signal Ground, TxD, RxD, RTS, CTS, DSR
and DTR. The lines TxD, RxD and RTS, CTS and DSR, DTR
must intersect.
The pin layout on the 24-pole connector for the serial interface
is as follows:
Pin number
Designation
(Chassis Ground)
TxD Transmit Data
RxD Receive Data
RTS Request to Send
CTS Clear to Send
DSR Data Set Ready
Signal Ground
DTR Data Terminal Ready
2
3
4
5
6
7
20
Designation
2
3
4
5
6
7
8
RxD
TxD
DTR
Signal Ground
DSR
RTS
CTS
35
HEIDENHAIN
DR. JOHANNES HEIDENHAIN GmbH
Dr.-Johannes-Heidenhain-Stral3e 5
D-83301 Traunreut, Deutschland
@ (08669) 31-O. lrxi56831
lEd(O8669) 5061
256 666 23
SW08
now?