Académique Documents
Professionnel Documents
Culture Documents
Al Akhawayn University
Objective: Modeling of a real life dynamic system (mainly related to vibrations). Then define
and modify the force expressions, parameter values and initial conditions, in a way that our
dynamic model simulation will synchronize with and draws itself on the video.
A.Introduction:
The dynamic behavior of structures is an important topic in many fields. Aerospace
engineers must understand dynamics to simulate space vehicles and airplanes, while mechanical
engineers must understand dynamics to isolate or control the vibration of machinery. In civil
engineering, an understanding of structural dynamics is important in the design and retrofit of
structures to withstand severe dynamic loading from earthquakes, hurricanes, and strong winds,
or to identify the occurrence and location of damage within an existing structure.
In this project we recorded four videos related to mechanical vibrations. Then we tried to analyze
and model those videos using tracker. Tracker is a video analysis and modeling program that
enables the creation of particle model simulations based on Newton's laws and to compare their
behavior directly with that of real world objects captured on a video.
mx + kx = 0
k
k
t)
+
B
cos
(
M
M t )
k
M is the angular natural frequency defined by
n = rad/sec
Summing the forces on the mass results in the following ordinary differential equation:
The result states that the mass will oscillate at the same frequency, f, of the applied force, but
with a phase shift
The amplitude of the vibration X is defined by the following formula.
Where r is defined as the ratio of the harmonic force frequency over the undamped natural
frequency of the massspringdamper model.
3) Torsional pendulum:
Let be the angle of rotation of the disk, and let
wire is untwisted.
A torsional pendulum.
Any twisting of the wire is inevitably associated with mechanical deformation. The wire resists
such deformation by developing a restoring torque, which acts to restore the wire to its
untwisted state. For relatively small angles of twist, the magnitude of this torque is directly
proportional to the twist angle. Hence, we can write
(1)
Where
is the torque constant of the wire. The above equation is essentially a torsional
equivalent to Hooke's law. The rotational equation of motion of the system is written
(2)
Where is the moment of inertia of the disk (about a perpendicular axis through its Centre).
The moment of inertia of the wire is assumed to be negligible. Combining the previous two
equations, we obtain
(3)
Equation (3) is clearly a simple harmonic equation. Hence, we can immediately write the
standard solution is
(4)
Where
(5)
We conclude that when a torsion pendulum is perturbed from its equilibrium state (i.e.,
),
it executes torsional oscillations about this state at a fixed frequency, , which depends only on
the torque constant of the wire and the moment of inertia of the disk. Note, in particular, that the
frequency is independent of the amplitude of the oscillation [provided remains small enough
that Eq. (1) still applies]. Torsion pendulums are often used for time-keeping purposes. For
instance, the balance wheel in a mechanical wristwatch is a torsion pendulum in which the
restoring torque is provided by a coiled spring.
The force generated by the mass is proportional to the acceleration of the mass as given
by Newtons second law of motion :
The
sum
of
the
forces
on
the
mass
then
generates
this ordinary
differential
equation:
Simple harmonic motion of the massspring system
Assuming that the initiation of vibration begins by stretching the spring by the distance of A and
releasing, the solution to the above equation that describes the motion of mass is:
This solution says that it will oscillate with simple harmonic motion that has
an amplitude of A and a frequency of fn. The number fn is called the undamped natural
frequency.
For
the
simple
massspring
system, fn is
defined
as:
The motion of the rigid body can be mathematically determined through traditional video
analysis of the y vs. t graph, v vs. t graph and a vs.t. In the Data Tool, select the region of data
that corresponds to the motion, from t = 0.000 to 4 s and a Curve Fit allows us to determine a Fit
Equation of y = A*sin (B*t+ C).
The forces exerted are: the weight and the spring force
Equation used:
The damped free vibration of the video can be mathematically determined through traditional
video analysis of the y vs. t graph, v vs. t graph and a vs.t. In the Data Tool, select the region of
data that corresponds to the motion, from t = 0.000 to 3 s and a vs. t graph. Curve Fit allows us to
determine a Fit Equation of y = A*sin (B*t+ C). The forces exerted are: the weight and the
spring force and the drag force
Equation used:
we have chosen in this case Theta as Y
The motion of the torsional pendulum can be mathematically determined through traditional video
analysis of the y vs. t graph, v vs. t graph and a vs.t. In the Data Tool, select the region of data that
corresponds to the motion, from t = 0.000 to 1.5 s and a Curve Fit allows us to determine a Fit Equation
of y = A*sin (B*t+ C).
The forces exerted are: the weight and the
Equation used:
The motion of the ruler can be mathematically determined through traditional video analysis of the y vs. t
graph, v vs. t graph and a vs.t. In the Data Tool, select the region of data that corresponds to the motion,
from t = 0.000 to 7 s and a Curve Fit allows us to determine a Fit Equation of y = A*sin (B*t+ C).
The forces exerted are: the weight and the drag force of the air, Initial force exerted on the ruler.
Simple pendulum:
Our video analysis and modeling:
Equation used:
The motion of the pendulum can be mathematically determined through traditional video analysis of the y
vs. t graph, v vs. t graph and a vs.t. In the Data Tool, select the region of data that corresponds to the
motion, from t = 0.000 to 2 s and a Curve Fit allows us to determine a Fit Equation of y = A*sin (B*t+ C)
The forces exerted are: the weight and the tension of the rope.
Ball oil:
Our video analysis and modeling:
Equation used:
The motion of the ball oil can be mathematically determined through traditional video analysis of the y
vs. t graph, v vs. t graph and a vs.t. In the Data Tool, select the region of data that corresponds to the
motion, from t = 0.000 to 6 s and a Curve Fit allows us to determine a Fit Equation of y = A*sin (B*t+ C)
are: the weight and the drag force of oil, the spring force.
SHMS scale:
Our video analysis and modeling:
Equation used:
The motion of SHMscale can be mathematically determined through traditional video analysis of the y vs.
t graph, v vs. t graph and a vs.t. In the Data Tool, select the region of data that corresponds to the motion,
from t = 0.000 to 2 s and a Curve Fit allows us to determine a Fit Equation of y = A*sin (B*t+ C)
The forces exerted are: the weight and the tension of the spring.
Discussion
After modeling and analyzing the videos we found that the majority of the graphs are pretty
much similar.
Conclusion:
2) References:
3) Appendix: