Académique Documents
Professionnel Documents
Culture Documents
extent within which variations of geometric form, as well as dimensions, are allowed
extent within which variations of geometric form, as well as tolerances, are allowed
extent within which variations of geometric form, as well as size, are allowed
extent within which variations of geometric form, as well as datum planes, are allowed
where a tolerance of size is specified, the limits of size of an individual feature prescribe the extent to which variation
where only a tolerance of size is specified, the limits of size of an individual feature prescribe the extent to which var
where only a tolerance of size is specified, the limits of size of an individual feature prescribe the extent to which var
where a tolerance of size is specified, the limits of size of an individual feature prescribe the extent to which variation
3. The actual local size of an individual feature at each cross section _______________.
shall be followed by a zero
shall be within the specified tolerance of shape
shall be within the specified tolerance of form
shall be within the specified tolerance of size
4.
What would be the resultant condition for the hole, if produced at a 30.1?
30.0
30.2
30.4
30.6
The surface or surfaces of a feature shall not extend beyond the boundary (envelope) of perfect form at MMC. This b
Where the actual local size of a feature has departed from MMC towards LMC, no variation in form is allowed equal
There is a requirement for a boundary of perfect form at LMC. Thus, a feature produced at its LMC limit of size is pe
All features are assumed to be at their maximum material condition.
Stock, such as bars, sheets, tubing, structural shapes, and other items produced to established industry or government
All dimensions that have overriding geometric tolerances.
Specially designed shapes.
Custom dimensions.
7. Where it is desired to permit a surface or surfaces of a feature to exceed the boundary of perfec
PERFECT FORM AT MMC NOT APPLICABLE
PERFECT FORM AT MMC NOT NECESSARY
PERFECT FORM AT MMC NOT REQUIRED
ANNOTATE THE BOUNDARY AS SHOWN
9. For inch dimensions where unilateral tolerances are used and either the plus or minus value is
be expressed with a 0 only
not be expressed
be expressed with the same number of decimal places, and the appropriate plus or minus sign
be expressed with an in designation
10. Where bilateral inch tolerancing is used both the plus and the minus values and the dimension
have the same number of decimal places
not use the +/- designation
have a bilateral symbol
have a 0 proceeding the decimal
11.
What would be the Resultant Condition Size of the pin, if produced at a 29.7?
29.6
29.8
30.0
30.2
12. Where limit dimensioning is used for inch tolerancing, and either the maximum or minimum
is left as is.
is shown without the + or sign.
has zeros added for uniformity.
is shown with the + or sign.
13. Where basic dimensions are used, for inch tolerancing, associated tolerances are expressed __
followed by a zero
not have the same number of places after the decimal point
without a following zero
with the same number of places after the decimal point
15.
What is the dimensioning method called between X and Y?
Base line dimensioning.
Chain dimensioning.
Direct dimensioning.
Linear dimensioning
16. For single limits, MIN or MAX is placed after a dimension where _______________.
other elements of the design definitely determine the other unspecified limits
the dimension is absolute.
the dimension is not absolute.
the dimension is a diameter.
17. Where an angular surface is defined by a combination of a linear dimension and an angle, ___
the surface must lie within two parallel planes.
the linear dimension takes precedence over the angle.
the angular dimension takes precedence.
the surface must lie within two non-parallel planes.
19.
What would be the resultant condition size of the hole, if produced at a 30.3?
30.4
30.2
30.0
29.8
21.
What is the dimensioning method called?
22.
What is the virtual condition for the pin in the figure if it was produced at the least material cond
29.4
29.5
29.9
30.0
24.
What is the meaning of the symbol?
The dimensional limit is related to an origin plane or axis.
The dimensional limit is all around.
The larger surface is used as the origin.
The dimensional limits come from the center.
26. Unless otherwise specified, tolerance of orientation, position,and datum references specified fo
minor diameter.
major diameter.
root diameter.
pitch cylinder.
27. The greatest tolerance accumulation will occur when which type of the following dimensionin
Chain dimensioning.
Base line dimensioning.
Direct dimensioning.
Geometric dimensioning.
28. Where either center lines or surfaces of features of a part are depicted on engineering drawin
a general note is required for clarification
each must be geometrically controlled
a basic angle is shown between the center lines or surfaces
is implied to be at 90 and is controlled the same as all other angular features
29. When unilateral tolerancing is used in the metric system and either the plus or minus value is
a single zero is shown without a plus or minus sign
both the plus and minus values will have the same decimals places
no value is used in the nil position
it is not used in the metric system
30. When a part is plated or coated, the dimensional limits apply _______________.
during plating
after plating
as specified on the drawing
before plating
31. Where a tolerance of position or orientation is applied on a zero tolerance at MMC basis, the
the actual mating size of the considered feature
the deviation of the considered datum feature
the deviation of the considered feature from LMC
the actual local size of the feature
32. At MMC, the virtual condition of an internal feature is a constant value _______________ its
equal to / plus
equal to / minus
regardless of / minus
regardless of / plus
33. At LMC, the virtual condition of an internal feature is a constant value _______________ its l
equal to / plus
equal to / minus
regardless of / minus
regardless of / plus
35. When using minimum or maximum after a dimension on a drawing for single limits. They are
36.
What is the virtual condition if the hole is, produced at 30.1?
30.6
30.4
30.2
30.0
37. For an external feature of size with a LMC modifier, the virtual condition is also called _____
outer boundary (locus).
VC outer boundary.
variable case boundary .
inner boundary (locus).
39. If a dimension has the possibility of being produced without satistical process control _______
designate both the statistical limits and the arithmetic stacking limits along with a note on the drawing
designate that each instance of the dimension be verified by inspection
specify, in a note, that it can not be produced in a non-SPC way specify, in a note, that the one-sided, mean-plus-three
designate both the statistical limits and the arithmetic stacking limits without a note on the drawing
40. Consideration to the collective effects of LMC and any applicable geometric tolerances need n
alignment hole location in establishing gage feature sizes
guaranteed area of contact
clearance between parts
thin wall conservation
41. The maximum variation between two features is equal to the sum of the tolerances on the two
chain
coordinate
base line
direct
43. Which of the following is not a valid method for expressing an inch tolerance value?
.748 - .750
500 +/- .005
.500 +.005
-.000
25 +/- .2
45.
What is wrong in the figure when using statistical tolerance symbol(s)?
The drawing is correct.
A note to explain the symbol(s) is required.
The ST symbol should not be used in the geometric tolerance.
The arithmetic limits must be specified to make it complete
46. The control of geometric form prescribed by limits of size does not apply to _______________
drilled holes
stock
keyways
reamed holes
47. When related to the form of an individual feature, the surface or surfaces shall not extend bey
LMC
virtual condition
MMC
resultant condition boundary
48. Circular runout, total runout, concentricity, and symmetry are applicable only on a ________
RFS
MMC
LMC
zero tolerance at MMC
49. Where a tolerance of position or orientation is applied on a zero tolerance at MMC basis, the
theoretical
approximate
actual
calculated
MMC applies, with respect to the individual tolerance, datum reference, or both, when no modifying symbol is prese
RFS applies, with respect to the individual tolerance, datum reference, or both, when no modifying symbol is present
LMC applies, with respect to the individual tolerance, datum reference, or both, when no modifying symbol is presen
MMC applies to the individual tolerance and RFS applies to the datum reference when no modifying symbol is prese
53. For a 25 0.5 hole with a tolerance of position applied on a zero tolerance at MMC basis, w
24.0
24.5
25.5
26.0
54. American Standard machine conical tapers are usually dimensioned by specifying the ______
composite profile tolerance
basic taper and basic diameter
taper name and number
size tolerance combined with a profile of a surface
55. Which one of the following will result in the greatest tolerance accumulation?
Base line dimensioning.
Chain dimensioning.
Direct dimensioning.
Limit dimensioning.
e _______________.
ibe the extent to which variations in its geometric form, as well as size, are allowed
rescribe the extent to which variations in its geometric form, as well as size, are allowed
rescribe the extent to which variations in its geometric tolerance, as well as size, are allowed
ibe the extent to which variations in its form, as well as dimensions, are allowed
_____________.
of perfect form at MMC. This boundary is the true geometric form represented by the drawing. No variation in form is permitted
riation in form is allowed equal to the amount of such a departure.
ed at its LMC limit of size is permitted to vary from true form to the maximum variation allowed by the boundary of perfect form
e of Size)?
eed the boundary of perfect form at MMC, a note such as _______________ is specified on the drawing.
he maximum or minimum value has digits following the decimal point, the other value _______________.
______________.
nsioning?
tum references specified for a screw thread applies to the axis of the thread derived from the ____________
__________.
alue _______________ its maximum material condition size, _______________ its applicable geometric tole
alue _______________ its least material condition size _______________ its applicable geometric tolerance.
e on the drawing
f the tolerances on the two dimensions from their origin to the features, describes _______________ dimens
n those heights
tween these sections
en the ends at MMC
tolerance value?
apply to _______________.
erance at MMC basis, the tolerance is totally dependant on the _______________ mating size of the conside
olerance at MMC basis, what is the largest possible pin that would be used to mate with the hole?
mulation?
o variation in form is permitted if the feature is produced at its MMC limit of size.
by the boundary of perfect form at MMC.
value _______________.
s _______________ dimensioning?