Académique Documents
Professionnel Documents
Culture Documents
com
ISRO TECHNICAL ASSISTANT MODEL PAPER (ELECTRONICS) SET-1
1. If 60 J of energy are available for every 15 C of charge, what is the voltage?
A.4 V B.60 V C.15 V D.0.25 V
Ans:E=QV V=E/Q=60/15=4V
2. Calculate the voltage at point B in the given circuit.
A. +10.48 V
B. +0.94 V
C. +2.6 V
D. -3 V
Ans: Here V2=12V and V1=9V (V2>V1) so current flow from V2 to V1
I=Veff/Rtot
Veff=V2-V1 (V1&V2 opposite to each other & V2>V1)
Veff=12-9=3V
Rtot= R1+R2+R3+R4=150kOhms
I=3/150 x10-3=0.02x10-3 A
VB = V2 - (VR3+VR4)
VB = V2 - .02x10-3(R3+R4) (Since current is equal in series circuit)
VB = 12 - 0.02x10-3x76x103
VB = 12-1.52
VB = 10.48 V
Why R1 and R2 are not considered for voltgae drop because no current from V1 to V2
3.In a 20 Vac series RC circuit, if 20 V is measured across the resistor and 40 V is measured across the
capacitor, the applied voltage is:
A. 45 V
B. 50 V
C. 55 V
D.60 V
Ans:
= + = 20 + 40 = 44.72 45
4. In a B-H curve, magnetizing force is equal to:
A. H=IxN/L
B.H = I N
C.ampere-turns per weber
D. webers per square meter
1|Page
A. 31.8 Hz
B. 32.3 Hz
C. 142 Hz
D. 7.2 kHz
Ans:For Series RLC circuit B.W=fr/Q
Q=(2*Pi*fr*L)/R
B.W = fr/((2*Pi*fr*L)/R) = R/2*Pi*L = 1000/2*3.14*5 = 31.8Hz
6. If a 169.7 V half-wave peak has an average voltage of 54 V, what is the average of two full-wave
peaks?
A. 119.9 V
B. 108.0 V
C. 115.7 V
D. 339.4 V
Ans: For half wave 54.0 So full wave 54*2=108
7. What is the cutoff frequency of this low-pass filter?
A. 4.8 kHz
B. 3.8 kHz
C. 2.8 kHz
D. 1.8 kHz
Ans: fc=1/(2*pi*R*C) = 1/(2*3.14*33*10^3*0.001*10^-6) = 4.8KHZ
8. The Hall effect application :
A. is a phenomenon with no practical applications
B. is used in various sensor applications
C. can develop potentials of thousands of volts
D. is the basis for solar cell operation
9. In a class B push-pull amplifier, the transistors are biased slightly above cutoff to avoid?
A. crossover distortion
B. unusually high efficiency
C. negative feedback
D. low input impedance
2|Page
B.semiconductors
C.insulators
D.neutral
12. If an input signal ranges from 2040 A (microamps), with an output signal ranging from .51.5 mA
(milliamps), what is the ac beta?
A. 0.05
B.20
C.50
D.500
13. Using voltage-divider biasing, what is the voltage at the gate VGS?
A. 5.2 V
B. 4.2 V
C. 3.2 V
D. 2.2 V
Ans: V(R2)=V(GS)= V(DD)*R2/(R1+R2)= (20*6K)/(6K+17K)=5.2V
14. Convert the decimal number 151.75 to binary.
A. 10000111.11
C. 00111100.00
B. 11010011.01
D. 10010111.11
3|Page
B. (1,2,4,7)
C. (, , , )
D. (0,3,5,6)
Ans: = (2 + 2 + + 2 ) = .
5
= ( 0.1 + 1.2 + 0.4 + 1.8)
2
B. 40
C.0.04
D.0.025
A. 2.325 mA
B. 5 mA
C. 1.25 mA
D. 0 mA
Ans: On +ve signal,diode1 is open and diode2 is forward biased and hence the op Volt vo=vi-vt
=10-0.7=9.3V
Reff=load resistance+2k
Reff= 2k+2k=4k
Hence I=vo/reff=9.3/(4*10^3)=2.325mA.
4|Page
A. 9.2 V
B. 9.9 V
C. 9.9 V
D. 9.2 V
Ans: Vbc=Vbe-Vce
So, first find out base current by kirchoff's loop law in input side .
Then collector current by Ic=b*Ib;
Now output kirchoff's current law at the output give value of Vce= 9.895;
Now Vcb = 0.7-9.895 = -9.195.
21. A certain fiber-optic cable has the following characteristics: n1 = 1.82 and n2 = 1.73. What is the
value of c?
A.71.90
B.0.95
C.18.1
D.1.81
A.20 V
B.11 V
C.10 V
D.9 V
5|Page
A. 20 dB/decade.
B. 40 dB/decade.
C. 60 dB/decade.
D. 80 dB/decade.
24. Calculate the value of C1 = C2 for the Wien bridge oscillator to operate at a frequency of 20 kHz.
Assume R1 = R2 = 50 k and R3 = 3R4 = 600?
A. 1.59 pF
B. 15.9 pF
C. 159 pF
D. 1.59 nF
Ans: f=1/(2*pi*sqrt(R1*R2*C1*C2)).
Since R1=R2=R=50k, C1=C2=C,
therefore
20k=1/(2*pi*50k*C),
C=159.15pF
6|Page
A. LOW
B. HIGH
C. Don't Care
D. Cannot be determined
27. Calculate IL for this circuit.
A. 3 mA
B.4 mA
C.5 mA
D.6 mA
Ans: IL = -Vo/4k ;
Vo = -(4k/2k)*10v;
IL = (20/4K) = 5 mA
7|Page
A.Low pass.
BHigh pass.
C.Band pass.
D.Band stop
29. A certain multiplexer can switch one of 32 data inputs to its output. How many different
inputs does this MUX have?
A.30 data inputs & 5 select inputs.
B.32 data inputs and 4 select inputs.
C.32 data inputs and 5 select inputs.
D.None of the above.
Ans: To represent 32 data input 5 selection lines are required 32 = 100000; N-input 2N selection lines
30. These are two ways in which a microprocessor can come out of Halt state.
8|Page