Académique Documents
Professionnel Documents
Culture Documents
3: Configure VTP
Topology Diagram
Learning Objectives
Introduction
In this activity, you will practice configuring VTP. When Packet Tracer first opens, the switches already
contain a partial configuration. The user EXEC password is cisco and the privileged EXEC password is
class.
Page 1 of 7
CCNA Exploration
LAN Switching and Wireless: VTP
____________________________________________________________________________________
____________________________________________________________________________________
Step 2. Display the current VLANs on each switch.
Are there any VLANs present? Are the VLANs user created VLANs or default VLANs?
____________________________________________________________________________________
S1#show vlan brief
VLAN Name
Status
Ports
---- ------------------------ --------- ----------------------------1
default
active
Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa0/16
Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
Gig1/1, Gig1/2
1002 fddi-default
active
1003 token-ring-default
active
1004 fddinet-default
active
1005 trnet-default
active
Completion should be at 0% at the end of this Task.
All contents are Copyright 2007-2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 2 of 7
CCNA Exploration
LAN Switching and Wireless: VTP
:
:
:
:
:
2
0
64
5
Client
All contents are Copyright 2007-2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 3 of 7
CCNA Exploration
LAN Switching and Wireless: VTP
Page 4 of 7
CCNA Exploration
LAN Switching and Wireless: VTP
30
99
1002
1003
1004
1005
Guest(Default)
Management&Native
fddi-default
token-ring-default
fddinet-default
trnet-default
active
active
active
active
active
active
If you enter the same command on S2 and S3, you will notice that the VLANs are not in their VLAN
database? Why not?
____________________________________________________________________________________
____________________________________________________________________________________
Step 4. Check results.
Your completion percentage should be 46%. If not, click Check Results to see which required
components are not yet completed.
All contents are Copyright 2007-2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 5 of 7
CCNA Exploration
LAN Switching and Wireless: VTP
Note: VTP advertisements are flooded throughout the management domain every five minutes or
whenever a change occurs in VLAN configurations. To accelerate this process, you can switch between
Realtime mode and Simulation mode until the next round of updates. However, you may have to do this
multiple times since this will only forward Packet Tracers clock by 10 seconds each time. Alternatively,
you can change one of the client switches to transparent mode and then back to client mode. (The
configuration revision numbering may differ on actual routers versus routers in Packet Tracer. This activity
is not grading the configuration revision numbers.)
What is the configuration revision number? ___________
Is the configuration revision number higher than the number of VLANs you created?
____________________________________________________________________________________
____________________________________________________________________________________
What is the current number of existing VLANs? ___________
Why are there more existing VLANs than the four you created?
____________________________________________________________________________________
Completion should still be at 77% at the end of this Task.
Fa0/11 on VLAN 10
Fa0/18 on VLAN 20
Fa0/6 on VLAN 30
Fa0/11 on VLAN 10
Fa0/18 on VLAN 20
Fa0/6 on VLAN 30
Page 6 of 7
CCNA Exploration
LAN Switching and Wireless: VTP
All contents are Copyright 2007-2008 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 7 of 7