Académique Documents
Professionnel Documents
Culture Documents
2003
The Beast
15 N ONE Multi-Purpose
Vehicle Jumpstart System
Instruction Manual
15 N ONE Multi-Purpose
Vehicle Jumpstart System
12 Volt DC - 10 A
Vehicle Jumpstart
System through Cigarette
Lighter Socket
Air Compressor
Engineered for Quick Inflating Rate
Reverse Jumpstart
Polarity Protection
Charging Port
Air Compressor
ON/OFF Switch
ON
OFF
IMPORTANT INFORMATION
READ AND UNDERSTAND ALL WARNINGS AND THE ADVISORY NOTES INCLUDED IN THIS
MANUAL. FOLLOW INSTRUCTIONS PROVIDED BY YOUR VEHICLE MANUFACTURER AND MANUFACTURER OF THE DEVICES INTENDED TO BE USED WITH THIS POWER SUPPLY.
MAKE CERTAIN THIS DEVICE IS FULLY CHARGED PRIOR TO FIRST USE.
Sheet 3 of 12
WARNINGS
Sheet 4 of 12
Sheet 5 of 12
1. Keep the Main Power Booster Clamps ON/OFF Switch in OFF position while charging.
2. Unfold the BEAST internal AC Charger prongs located on the side of booster clamp compartment.
3. Attach an 18 gauge (AWG) or larger wire gauge extension cord to the internal charger plug.
(Extension cord is included ). Refer to page 3 of this manual.
4. Connect the other end of the extension cord into the 110 Volt AC home receptacle.
5. Fully charge the BEAST according to the following schedules:
First time charge:
36 hours
Recharge and subsequent charge: 24 hours
6. Unplug the extension cord from the 110 Volt receptacle first and then unplug the extension cord from
the BEAST internal charger unit.
B. DC Charging In Your Vehicle with 12 Volt Charger
1. Keep the Main Power Booster Clamps ON/OFF Switch in OFF position while charging.
2. Insert the 12 Volt DC Charger round Plug into the BEAST Charging Port.
3. Connect the 12 Volt DC Charger Plug into the vehicle cigarette lighter or 12 Volt accessory port.
4. Fully charge the unit internal battery for 8 hours while the vehicle engine is running.
5. Unplug the DC charger from the vehicle cigarette lighter or 12 Volt accessory port first and then
remove the round plug from the BEAST Charging Port.
Sheet 6 of 12
IMPORTANT: The Internal auto-reset Circuit Breaker will automatically interrupt the power if the current
drawn exceeds 10Amp.This feature prevents damage to the BEAST internal circuits. Internal Circuit Breaker
will automatically reset after cooling period (Approximately 10-25 minutes).
1. Prior to connecting the device to be powered to the inverter, make sure the inverter power switch is
in OFF position.
2. Prior to plug in the device, make sure the device power switch is OFF and ensure the current drawn
by this device is not to exceed 400W maximum power consumption.
3. Remove the plastic protective covers from the inverter receptacles.
4. Connect the device 110 Volt AC electrical plug into the inverter receptacle.
5. Turn ON the inverter power switch to I position. If the inverter is operating properly, the green LED
indicator will illuminate. Now turn ON the device. If the green indicator remains on, the system is
operating properly. If the inverter green LED light turns RED, turn off the device then turn the power
switch to O position to turn OFF the inverter immediately. See the trouble shooting guide. The
inverter may have been over loaded or the input voltage may be too low.
CAUTION:
Some rechargeable devices are equipped with a separate charger, which can be connected into this
inverter AC receptacle. However certain rechargeable devices are manufactured with built-in chargers
(see device owners manual). This category of devices may cause internal damage to inverters and
should not be used with this inverter. The temperature of the device must be monitored for the first 15
minutes of operation. Abnormally elevated temperature of the device is an indication that they should not
be used with this inverter.
Inverter Status Indicator LED
Inverter power ON position
Sheet 7 of 12
1. Turn off the vehicle ignition and all the accessories (Such as radios, lights, and air conditioners,
etc.).
2. Apply the emergency brake and put those vehicles with automatic transmission in park position.
3. Place the BEAST unit in the vehicle front passenger side floor board.
4. Connect the Booster Cable 12 Volt DC plug with LED power indicator into the vehicle cigarette lighter or 12Volt DC socket.
5. Connect the other end of the Booster Cable into the BEAST unit 12 Volt DC port. Make certain a
good connection is made.
6. Allow a minimum of 20 minutes for the vehicle depleted battery to boost charge.
7. Disconnect the dual 12 Volt DC plug Booster Cable from the vehicle and from the BEAST 12 Volt
DC port.
8. Start the vehicle engine.
Electronics Device
2 Watt
4 Watt
5 Watt
8 Watt
20 Watt
25 Watt
30 Watt
50 Watt
IMPORTANT NOTE: The above listing is prepared for reference purposes ONLY. Certain electronic devices exceed the power consumption wattage listed. Prior to powering the intended electronic devices,
refer to and review the Instruction Manual for actual wattage requirement.
FULL
100%
Charge
Level
75%
Charge
Level
Battery Charge
Level Status
Push Button
50%
Charge
Level
Low
Charge
Level
Sheet 8 of 12
Allow 3 to 5 minutes of charge time. It is highly recommended having a second person to assist
holding the unit securely in place during the next steps.
9. Start the engine and Stop if the vehicle does not start after 2 to 3 seconds of engine cranking. Wait
2 to 3 minutes then try again. Repeat the above steps several times until the vehicle starts.
10. If the vehicle starts, turn off the Main Power Switch by turning the switch to the OFF position.
11. Disconnect the clamps as far away from the vehicle battery as possible.
For Negative Grounded System, disconnect the BLACK CLAMP Negative first and then the RED
then the BLACK CLAMP Negative.
12. Stow the booster clamps into their storage compartment.
Sheet 9 of 12
CLAMP Positive. For Positive Grounded System, disconnect the RED CLAMP Positive first, and
Right
ON/OFF Push
Lens
Aligning peg
Aligning slot
Left
Sheet 10 of 12
RECOMMENDED SOLUTION
Make sure the Polarity Protection Green LED is illuminated. Turn the Main
Power Switch to ON Position to allow power into the booster clamps.
DO NOT turn the Main Power Switch to ON position if the Polarity
Protection RED LED is illuminated. Disconnect both booster clamps and
reconnect the Booster Clamps to the proper polarity.
Allow the BEAST to stay connected to the vehicle battery for a longer
period of time. Wait 6 to 8 minutes before attempting to start the vehicle
again.
Recharge the BEAST to a FULL charge status.
Replace the vehicle battery or visit workshop/garage for further
assistance.
12 Volt DC devices
connected to the 12 Volt
output port of the BEAST
does not operate.
Make sure the hose nozzle is properly seated and the locking lever is in
down position.
Repair air hose if possible.
Sheet 11 of 12
Sheet 12 of 12
MobilePower, LLC. 198 Okatie Village Drive . Suite 103-312 . Bluffton, SC 29909