Académique Documents
Professionnel Documents
Culture Documents
FACTDRFMADE
WROUGHT
BUTTWELDIMG
FITTINGS
ASME B16.N-2001
This Standard will be revised when the Society approves the issuance of a
new edition. There will be no addenda issued to this edition. The next edition
of this Standard is scheduled for publication in 2005.
This code or standard was developed under procedures accredited as meeting the criteria for
American National Standards. The Standards Committee that approved the code or standard
was balanced to assure that individuals from competent and concerned interests have had an
opportunity t o participate. The proposed code or standard was made available for public review
and comment that provides an opportunity for additional public input from industry, academia,
regulatory agencies, and the public-at-large.
ASME does not "approve," "rate," or "endorse" any item, construction, proprietary device,
or activity.
ASME does not take any position with respect t o the validity of any patent rights asserted i n
connection with any items mentioned in this document, and does not undertake to insure anyone
utilizing a standard against liability for infringement of any applicable letters patent, nor assume
any such liability. Users of a code or standard are expressly advised that determination of the
validity of any such patent rights, and the risk of infringement of such rights, is entirely their
own responsibility.
Participation by federal agency representative(s) or persons) affiliated with industry is not to
be interpreted as government or industry endorsement of this code or standard.
ASME accepts responsibility for only those interpretations o f this document issued i n
accordance with the established ASME procedures and policies, which precludes the issuance
of interpretations by individuals.
Copyright Q 2001 by
THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS
All Rights Reserved
Printed in U.S.A.
...
111
Requests for interpretation or suggestions for revision should be sent to the Secretary,
B16 Committee, The American Society of Mechanical Engineers, Three Park Avenue, New
York, NY 10016.
This Standard was approved as an American National Standard on April 6, 2001.
iv
OFFICERS
W. N. McLean, Chair
H. R. Sonderegger, Vice Chair
P. Reddington, Secretary
COMMITTEE PERSONNEL
W. L. Ballis, Columbia Gas Distribution Co.
J. E. Batey, Union Carbide Corp.
K. M. Bell, Underwriter's Laboratory, Inc.
M. L. Blair, U S . Coast Guard
R. R. Brodin, Fisher Controls International, Inc.
A. Cohen, Copper Development Association
W. C. Farrell, Jr., Consultant
C. E. Floren, Mueller Co.
D. R. Frikken, Monsanto Co.
M. W. Garland, Frick Co.
J. B. Hagen, ABS Americas
J. C. Inch, Mueller Brass Co.
J. S. John, J Square Engineering Co.
G. A. Jolly, Vogt Valve Co.
W. G. Knecht, Anchor/Darling Valve Co.
R. Koester, The William Powell Co.
J. H. Longacre, Nibco, Inc.
J. H. McCauley, Jr., James H. McCauley, Inc.
W. N. McLean, Newco Valves
A. F. Rhodes, Arnco Technology Trust
F. C. Rosch, Jr., Techincon Enterprises, Inc.
R. A. Schmidt, Ladish Co.
H. R. Sonderegger, Tyco Flow Control
W. M. Stephan, Flexitallic Inc.
T. F. Stroud, Ductile Iron Pipe Research Association
R. E. White, Repairs, Inc.
D. A. Williams, Southern Company Services
L. A. Willis, Dow Chemical Co.
SUBCOMMITTEE F
WELDING FITTINGS
R. E. Johnson, Consultant
R. C. Laffetty, Penna Machine Works, Inc.
D. H. Monroe, Consultant
R. A. Schmidt, Ladish Co.
H. R. Sonderegger, Tyco Flow Control
L. A. Willis, Dow Chemical Co.
W. R. Worley, Union Carbide
VI
CONTENTS
Foreword ............................................................................
Committee Roster ....................................................................
1
...
111
Scope ..........................................................................
1.1 General .....................................................................
1.2 Special Fittings ..............................................................
1.3 Fabricated Fittings ...........................................................
1.4 Standard Units ..............................................................
1.5 References ..................................................................
1.6 Service Conditions ...........................................................
1.7 Welding ....................................................................
1.8 Quality Systems .............................................................
1.9 Convention ..................................................................
1
2
............................................................................
1
1
1
1
1
1
1
1
1
Size
Marking ........................................................................
4.1 Standard Marking ............................................................
4.2 Exceptions ..................................................................
4.3 Depth of Stamping ..........................................................
4.4 Compliance .................................................................
2
2
2
2
2
Material
........................................................................
3
3
3
Surface Contours
..............................................................
3
3
3
3
4
..............................................................
10 Production Tests
vii
11 Tolerances
.................................................................
Figure
1 Maximum Envelope for Welding End Transitions ..................................
Tables
1 Welding Bevels and Root Face ...................................................
2 Tolerances .......................................................................
3 Dimensions of Long Radius Elbows ..............................................
4 Dimensions of Long Radius-Reducing Elbows .....................................
5 Dimensions of Long Radius Returns ..............................................
6 Dimensions of Short Radius Elbows ..............................................
7 Dimensions of Short Radius 180 Deg Returns .............................
....
8 Dimensions of Straight Tees and Crosses .........................................
9 Dimensions of Reducing Outlet Tees and Reducing Outlet Crosses . . . . . . . .
....
10 Dimensions of Lap Joint Stub Ends ..............................................
11 Dimensions of Caps .............................................................
12 Dimensions of Reducers ..........................................................
Mandatory Appendices
I Inch Tables ......................................................................
II References ...................................................................
Nonmandatory Appendices
A Quality System Program ..........................................................
viii
5
5
4
6
8
9
10
IO
II
11
12
17
18
19
21
36
ASME 616.9-2001
1 SCOPE
1.1 General
This Standard covers overall dimensions, tolerances,
ratings, testing, and markings for wrought factory-made
buttwelding fittings in sizes NPS /2 through 48 (DN
15 through 1200).
1.7 Welding
Fabricated laterals and other fittings employing circumferential or intersection welds are considered pipe
fabrication, and are not within the scope of this Standard.
1.9 Convention
For the purpose of determining conformance with
this Standard, the convention for fixing significant digits
where limits, maximum or minimum values, are specified shall be rounded off as defined in ASTM E 29.
This requires that an observed or calculated value shall
be rounded o f f to the nearest unit in the last righthand digit used in expressing the limit. Decimal value
in the last and tolerances do not imply a particular
method of measurement.
1.5 References
1.5.1 Referenced Standards. Standards and specifications adopted by reference in this Standard are
shown in Mandatory Appendix II. It is not considered
practical to identify the specific edition of each standard
and specification in the individual references. Instead,
the specific edition reference is identified in Mandatory
Appendix II. A product made in conformance with a
prior edition of reference standards and in all other
respects conforming to this Standard will be considered
to be in conformance.
2 PRESSURE RATINGS
2.1 Basis of Ratings
The allowable pressure ratings for fittings designed
in accordance with this Standard may be calculated as
for straight seamless pipe of equivalent material (as
shown by comparison of composition and mechanical
properties in the respective material specifications) in
accordance with the rules established in the applicable
1
ASME 816.9-2001
3 SIZE
NPS, followed by a dimensionless number, is the
designation for nominal fitting size. NPS is related to the
reference nominal diameter, DN, used in international
standards. The relationship is, typically, as follows:
DN
15
20
25
32
40
50
65
80
100
NPS
?;
/4
1 /4
112
24
4 MARKING
4.1 Standard Marking
Each fitting shall be permanently marked to show
the following:
(a) manufacturers name or trademark.
(b) material identification, either the ASTM or ASME
grade designation.
(c) schedule number or nominal wall thickness in
mm.
e
\
4.2 Exceptions
Where the size of the fitting does not permit complete
marking, the identification marks may be omitted in
reverse of the order presented above.
4.4 Compliance
4.4.1 Standard Fittings. That the fitting was manufactured in conformance with this Standard, including
all dimensional requirements, is certified by a prefix
WP in the material grade designation marking.
4.4.2 Special Fittings. That the fitting was manufactured in conformance with this Standard except that
dimensional requirements are as agreed between the
purchaser and the manufacturer, is certified by a supplementary suffix to the material grade designation marking
as follows:
(a) S9 applies for fittings in accordance with ASTM
A 234 and A 403.
(6) S6 applies for fittings in accordance with ASTM
A 420.
(c) S8 applies for fittings in accordance with ASTM
A 815.
() SPLD applies for fittings in accordance with
ASTM B 361, B 363, and B 366.
5 MATERIAL
ASME B16.9-2001
6 FITTINGS DIMENSIONS
6.1 General
This Standard provides for a fixed position for the
welding ends with reference to either the center line
of the fittings or the overall dimensions. Dimensional
requirements for these fittings are to be found in Tables
3 through 12 and Tables I1 through I12 of Mandatory
Appendix I.
7 SURFACE CONTOURS
p = -2Sr
D
8 END PREPARATION
where
s=
fitting
actual tensile strength of the test fitting, determined on a specimen representative of the test
fitting, which shall meet the tensile strength
requirements of the applicable material of section 5.
ASME 616.9-2001
r
D
22 (0.88) max.
Note (1.)
Note (11
(Root face)
Thickness, t
End Preparation
x to 22 (0.88) included
Compound bevel as in
sketch (b) above.
GENERAL NOTES:
(a) Dimensions i n parentheses are in inches.
(b) Other dimensions are i n millimeters.
NOTES:
(1) See section 8 and Fig. 1 for transition contours.
(2) x = 5 (0.19) for carbon steel or ferritic alloy steel and 3
(0.12) for austenitic alloy steel.
9.4.3 Material Grades. The pressure retaining capacity of a geometrically identical fitting made of
various grades of steel will be directly proportional to
the tensile properties of the various grades; see para
2.1. Therefore, it is necessary to test only a single
material grade in a representative fitting to prove the
design of the fitting.
ASME 816.9-2001
-- --
-----
1.5fmin
__i
Outside
Note (3)
Component of Fiting
I
I
\
\
\
\
\
\
\I
Radius 2 0.05tmin
,----I
Inside
NOTES:
(1) The value of tmin is whichever of the following is applicable:
(a) the minimum ordered wall thickness of the pipe;
(b) 0.875 times the nominal wall thickness of pipe ordered to a pipe schedule wall thickness
that has an undertolerance of 12.5%.
(2) The maximum thickness at the end of the component is:
(a) the greater of [tmin +4mm (0.16 in.)] or l.15fmin when ordered on a minimum wall basis;
(b) the greater of [tmin +4mm (0.16 in.)] or l.lOtnom when ordered on a nominal wall basis.
(3) Weld bevel shown is for illustration only.
(4) The weld reinforcement permitted by applicable code may lie outside the maximum envelope.
(5) Where transitions using maximum slope do not intersect outside surface within the
transition region, as shown by phantom outline, maximum slopes shown shall be used.
Alternately, radii lying within the envelope may be used.
11 TOLERANCES
ASME 816.9-2001
@
+ -
\
I
ASME 816.9-2001
. .
w w w w w w : :
O 0
o o o o o o m o
o o o o o m o h l
- m m
PYS
w w w w c g :
LALAAooooo
r h l m m m m o o
-cvmdwco=
. .
m m m w w w ~ ~
"hlcvcvcvmm
- - c v " N .
+ : :
ASME 816.9-2001
I - A l
-+-
CentertoCenter,
D
21.3
26.7
33.4
42.2
48.3
76
76
76
95
114
48
51
56
70
83
50
65
80
90
100
60.3
73.0
88.9
101.6
114.3
152
190
229
267
305
106
132
159
184
210
5
6
8
10
12
125
150
200
250
300
141.3
168.3
219.1
273.0
323.8
381
457
610
762
914
14
16
18
20
22
24
350
355.6
406.4
457
508
559
61O
1067
1219
1372
1524
1676
1829
Nominal
Pipe
Size
(NPS)
'12
74
1
15%
1/'2
DN
15
20 [Note (3)l
25
32
40
400
450
500
550
600
Nominal
Pipe
Size
DN
Outside
Diameter
at
Bevel
Centerto-End,
A
25
32
40
50
65
33.4
42.2
48.3
60.3
73.0
25
32
38
51
64
3
3/'2
4
5
6
80
90
1O0
125
150
88.9
101.6
114.3
141.3
168.3
76
89
102
127
152
262
313
414
518
619
8
10
12
14
16
200
250
300
350
400
219.1
273.0
323.8
355.6
406.4
203
254
305
356
406
71 1
813
914
1016
1118
1219
18
20
22
24
450
500
550
600
457
508
559
610
457
508
559
610
BacktoFace,
N")
~~
10
ASME 816.9-2001
-+1
TABLE 7
Nominal
Pipe
Size
(NPS)
Nominal
Pipe
Size
(NPS)
DN
~~
Outside
Diameter
at Bevel
CentertoCenter,
O
BacktoFace,
K
25
32
40
50
65
33.4
42.2
48.3
60.3
73.0
51
64
76
102
127
41
52
62
81
1 O0
3
3'/2
4
5
6
80
90
1 O0
125
150
88.9
101.6
114.3
141.3
168.3
152
178
203
254
305
121
140
159
197
237
8
10
12
14
16
200
250
300
350
400
219.1
273.0
323.8
355.6
406.4
406
508
610
711
813
313
391
467
533
610
18
20
22
24
450
500
550
600
457
508
559
610
914
1016
1118
1219
686
762
838
914
GENERAL NOTES:
(a) All dimensions are i n millimeters.
(b) Dimension A is equal t o one-half of dimension O.
Center-to-End
Run,
C
Outlet, M
[Notes (1)and (211
1
15 4
1 '/2
15
20
25
32
40
21.3
26.7
33.4
42.2
48.3
25
29
38
48
57
25
29
38
48
57
2
2'12
3
3'4
4
50
65
80
90
1 O0
60.3
73.0
88.9
101.6
114.3
64
76
86
95
105
64
76
86
95
105
5
6
8
10
12
125
150
200
250
300
141.3
168.3
219.1
273.0
323.8
124
143
178
216
254
124
143
178
216
254
14
16
18
20
22
350
400
450
500
550
355.6
406.4
457
508
559
279
305
343
381
419
279
305
343
381
419
24
26
28
30
32
600
650
700
750
800
610
660
711
762
813
432
495
521
559
597
432
495
521
559
597
34
36
38
40
42
850
900
950
1050
864
914
965
1016
1067
635
673
71 1
749
762
635
673
711
749
71 1
44
46
48
1100
1150
1200
1118
1168
1219
813
851
889
762
800
838
'12
"4
1
1 5%
1 '/2
2
2'/2
DN
Outside
Diameter
at Bevel
1000
11
ASME 816.9-2001
Outside Diameter at
Bevel
DN
Center-to-End
Run
Outlet
Run,
C
Outlet; M
INote (111
x Y2 x Y0
/2 x /4
Y4 x Y4 x Y2
4
x Y4 x Y0
1xlxY4
1 x 1 x /2
15%x 15% x 1
1114 x 1/4 x Y4
1/4 x 1/4 x Y
2
11/2 x 1/2 x 15%
112 x 1/2 x 1
112 X 2/
X Y4
152 x 1/2 x Y2
15x
15x
20x
20x
25 x
25x
32x
32x
32x
40 x
40 x
40 x
40x
15x
15x
20x
20x
25 x
25x
32x
32x
32x
40 x
40 x
40 x
40x
10
8
15
10
20
15
25
20
15
32
25
20
15
21.3
21.3
26.7
26.7
33.4
33.4
42.2
42.2
42.2
48.3
48.3
48.3
48.3
17.3
13.7
21.3
17.3
26.7
21.3
33.4
26.7
21.3
42.2
33.4
26.7
21.3
25
25
29
29
38
38
48
48
48
57
57
57
57
25
25
29
29
38
38
48
48
48
57
57
57
57
2 x 2 x 1/2
2 ~ 2 ~ 1 5 %
2X2X1
2 x 2 x 3/4
50
50
50
50
x
x
x
x
50x
50x
50x
50 x
40
32
25
20
60.3
60.3
60.3
60.3
48.3
42.2
33.4
26.7
64
64
64
64
60
57
51
44
214 x 2/2 x 2
214 x 21/2 x 1/2
Z1/2 X 212 X 114
214 x 214 x 1
65x
65 x
65 x
65x
65 x
65 x
65 x
65x
50
40
32
25
73.0
73.0
73.0
73.0
60.3
48.3
42.2
33.4
76
76
76
76
70
67
64
57
3 x 3 x 24
3 x 3 ~ 2
3 x 3 x 1/2
3x3x15/,
80 x
80x
80x
80x
80
80
80
80
65
50
40
32
88.9
88.9
88.9
88.9
73.0
60.3
48.3
42.2
86
86
86
86
83
76
73
70
101.6
101.6
101.6
101.6
88.9
73.0
60.3
48.3
95
95
95
95
92
89
83
79
/2
4 x
x
x
x
x
4 X 4 X 3/2
4X4X3
4x4x2/2
4 x 4 ~ 2
4 x 4 x 172
1 o o x 100 x 90
1OOx 1OOx 80
100 x 1OOx 65
1OOx 1OOx 50
1 0 0 x 1 0 0 ~40
114.3
114.3
113.3
114.3
114.3
101.6
88.9
73.0
60.3
48.3
105
105
105
105
105
102
98
95
89
86
5X5X4
5 X 5 X 3/2
5X5X3
5 x 5 x 2/,
5 x 5 ~ 2
1 2 5 x 1 2 5 x 100
1 2 5 x 1 2 5 ~90
1 2 5 x 1 2 5 ~80
1 2 5 x 1 2 5 ~65
125x 125 x 50
141.3
141.3
141.3
141.3
141.3
114.3
101.6
88.9
73.0
60.3
125
124
124
124
124
117
114
111
108
105
(continued)
12
ASME 616.9-2001
Outside Diameter at
Bevel
DN
Run
Center-to-End
Outlet
Run,
C
Outlet, M
[Note (111
~ 5
~ 4
3'4
~ 3
2'4
150 x
150x
150 x
150x
150x
150 x
150x
150 x
150x
150x
125
100
90
80
65
168.3
168.3
168.3
168.3
168.3
141.3
114.3
101.6
88.9
73.0
143
143
143
143
143
137
130
127
124
121
8 x 8 ~ 6
8X8X5
8 x 8 ~ 4
8 x 8 x 3'/2
200 x
200 x
200 x
200x
200 x
200 x
200 x
200 x
150
125
100
90
219.1
219.1
219.1
219.1
168.3
141.3
114.3
101.6
178
178
178
178
168
162
156
152
10 x 10 x
10 x 10 x
10x10
10 x 10 x
250
250
250
250
x 250 x 200
x 250 x 150
x 250 x 125
x 250 x 100
273.0
273.0
273.0
273.0
219.1
168.3
141.3
114.3
216
216
216
216
203
194
191
Ia4
12 x 12 x 10
12 x 12 x 8
12x12~6
12 x 12 x 5
323.8
323.8
323.8
323.8
273.0
219.1
168.3
141.3
254
254
254
254
241
229
219
216
14 x 14 x
14 x 14 x
14 x 1 4 x
14x14
12
10
8
~6
350
350
350
350
x 350 x 300
x 350 x 250
x 350 x 200
x 350 x 150
355.6
355.6
355.6
355.6
323.8
273.0
219.1
168.3
279
279
279
279
270
257
248
238
16 x 16 x 14
16 x 16 x 12
16 x 16 x 10
16x16~8
16 x 16 x 6
400
400
400
400
400
x 400 x
x 400 x
x 400 x
x 400 x
x 400 x
350
300
250
200
150
406.4
406.4
406.4
406.4
406.4
355.6
323.8
273.0
219.1
168.3
305
305
305
305
305
305
295
283
273
264
18 x
18 x
18 x
18 x
18 x
16
14
12
10
8
450 x
450 x
450 x
450 x
450 x
450 x
450 x
450 x
450 x
450 x
400
350
300
250
200
457
457
457
457
457
406.4
355.6
323.8
273.0
219.1
343
343
343
343
343
330
330
321
308
298
20x20~
18
20 x 20 x 16
20 x 20 x 14
20X20X12
20 x 20 x 10
20 x 20 x 8
500 x
500 x
500 x
500 x
500 x
500 x
500 x
500 x
500 x
500 x
500 x
500 x
450
400
350
300
250
200
508
508
508
508
508
508
457
406.4
355.6
323.8
273.0
219.1
381
381
38 1
381
381
381
368
356
356
346
333
324
22
22
22
22
22
22
550 x
550 x
550 x
550 x
550 x
550 x
550 x
550 x
550 x
550 x
550 x
550 x
500
450
400
350
300
250
559
559
559
559
559
559
508
457
406.4
355.6
323.8
273.0
419
419
419
419
419
419
406
394
38 1
381
37 1
359
6 x 6
6 x 6
6x 6x
6 x 6
6x 6x
x
x
x
x
x
x
18 x
18 x
18 x
18 x
18 x
22 x
22 x
22 x
22 x
22 x
22 x
8
6
~5
4
20
ia
16
14
12
10
(continued)
13
ASME 816.9-2001
Outside Diameter at
Outlet
Run,
C
Outlet, M
[Note (111
Bevel
DN
Run
Center-to-End
600 x
600 x
600 x
600 x
600 x
600 x
600 x
600 x
600 x
600 x
600 x
600 x
600 x
600 x
550
500
450
400
350
300
250
610
610
610
610
61O
61O
610
559
508
457
406.4
355.6
323.8
273.0
432
432
432
432
432
432
432
432
432
419
406
406
397
384
26 x 26 x 24
26 x 26 x 22
26 x 26 x 20
26x26~18
26x26~16
26 x 26 x 14
26x26~12
650
650
650
650
650
650
650
650 x
650 x
650 x
650 x
650 x
650 x
650 x
600
550
550
450
400
350
300
660
660
660
660
660
660
660
61O
559
508
457
406.4
355.6
323.8
495
495
495
495
49 5
495
495
483
47 O
457
444
432
432
422
28
28
28
28
28
28
28
28
711
711
711
711
711
71 1
71 1
71 1
660
610
559
508
457
406.4
355.6
323.8
521
521
521
521
521
521
52 1
521
521
508
495
483
470
457
457
448
30 x 30 x 28
30 x 30 x 26
30 x 30 x 24
30 x 30 x 22
30 x 30 x 20
30x30~18
30x30~16
30 x 30 x 14
30 x 30 x 12
30 x 30 x 10
750x750~700
750 x 750 x 650
750 x 750 x 600
750 x 750 x 550
750 x 750 x 500
750 x 750 x 450
750 x 750 x 400
750 x 750 x 350
750 x 750 x 300
750 x 750 x 250
762
762
762
762
762
762
762
762
762
762
711
660
61O
559
508
457
406.4
355.6
323.8
273.0
559
559
559
559
559
559
559
559
559
559
546
546
533
521
508
495
483
483
473
460
32
32
32
32
32
32
32
32
32
x
x
x
x
x
x
x
x
x
32
32
32
32
32
32
32
32
32
800 x
800 x
800 x
800 x
800 x
800 x
800 x
800 x
800 x
800 x
800 x
800 x
800 x
800 x
800 x
800 x
800 x
800 x
750
700
650
600
550
500
450
400
350
813
813
813
813
813
813
813
813
813
762
71 1
660
610
559
508
457
406.4
355.6
597
597
597
597
597
597
597
597
597
584
572
572
559
546
533
521
508
508
34
34
34
34
34
34
34
x
x
x
x
x
x
x
34 x
34 x
34 x
34 x
34 x
34 x
34 x
850 x
850 x
850 x
850 x
850 x
850 x
850 x
850 x 800
850 x 7 5 0
850 x 700
850 x 650
850 x 600
850 x 550
850 x 500
864
864
864
864
864
864
864
813
762
711
600
61O
559
508
635
635
635
635
635
635
635
622
610
597
597
584
572
559
24 x 24 x
24 x 24 x
24 x 24 x
24 x 24 x
24 x 24 x
24x24
24 x 24 x
x
x
x
x
x
x
28
28
28
28
28
28
x 28
x 28
22
20
18
16
14
~
12
10
x
x
x
x
x
x
26
24
22
20
18
16
x 14
x 12
x
x
x
x
x
x
x
x
30
28
26
24
22
20
18
16
x 14
32
30
28
26
24
22
20
x
x
x
x
x
x
x
(contin uedl
14
ASME 816.9-2001
Outside Diameter at
Run
DN
Center-to-End
Outlet
Run,
C
Outlet, M
[Note (1I1
Bevel
34x34~18
3 4 x 3 4 16
~
864
864
457
406.4
635
635
546
533
36 x
36 x
36 x
36 x
36 x
36 x
36 x
36 x
36 x
36 x
36 x
36 x
36 x
36 x
36 x
36 x
36 x
36 x
36 x
36 x
34
32
30
28
26
24
22
20
18
16
914
914
914
914
914
914
914
914
914
914
864
813
762
711
660
610
559
508
457
406.4
673
673
673
673
673
673
673
673
673
673
660
648
635
622
622
610
597
584
572
559
38 x
38 x
38 x
38 x
38 x
38 x
38 x
38 x
38 x
38 x
38 x
38 x
38 x
38 x
38 x
38 x
38 x
38 x
38 x
38 x
36
34
32
30
28
26
24
22
20
18
950 x
950 x
950 x
950 x
950 x
950 x
950 x
950 x
950 x
950 x
965
965
965
965
965
965
965
965
965
965
914
864
813
762
711
660
610
559
508
457
711
711
711
711
711
711
71 1
711
711
711
711
698
686
673
648
648
635
622
610
597
40 x
40 x
40 x
40 x
40 x
40 x
40 x
40 x
40 x
40 x
40 x
40 x
40 x
40 x
40 x
40 x
40 x
40 x
40 x
40 x
40 x
40 x
38
36
34
32
30
28
26
24
22
20
18
1000 x
1ooox
1000 x
1000 x
1000 x
1000 x
1000 x
1000 x
1000 x
1000 x
1000 x
1000 x 950
1000x900
1000 x 850
1000 x 800
1000 x 750
1000 x 700
1000 x 650
1000 x 600
1000 x 550
1000 x 500
1000 x 450
1016
1016
1016
1016
1016
1016
1016
1016
1016
1016
1016
965
914
864
813
762
711
560
610
559
508
457
749
749
749
749
749
749
749
749
749
749
749
749
737
724
711
698
673
673
660
648
635
622
42
42
42
42
42
42
42
42
42
42
42
42
42
42 x
42 x
42 x
42 x
42 x
42 x
42 x
42 x
42 x
42 x
42 x
42 x
42 x
40
38
36
34
32
30
28
26
24
22
20
18
16
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1050 x
1000
950
900
850
800
750
700
650
600
550
500
450
400
1067
1067
1067
1067
1067
1067
1067
1067
1067
1067
1067
1067
1067
1016
968
914
864
813
762
711
660
610
559
508
457
406.4
762
762
762
762
762
762
762
762
762
762
762
762
762
711
711
711
711
711
711
698
698
660
660
660
648
635
1118
1118
1067
1016
813
813
762
749
x
x
x
x
x
x
x
x
x
x
x
x
x
44 x 44 x 42
44x44~40
950 x
950 x
950 x
950 x
950 x
950 x
950 x
950 x
950 x
950 x
900
850
800
750
700
650
600
550
500
450
(con tinuedl
15
ASME 816.9-2001
Outside Diameter at
DN
Run
Center-to-End
Outlet
Run,
C
Outlet, M
[Note (111
Bevel
44x44~38
44x44~36
44X44X34
44x44~32
44x44~30
44x44~28
44x44~26
44x44~24
44 x 44 x 22
44X44X20
1100 x
1100 x
1100 x
1100 x
1100 x
1100 x
1100 x
1100 x
1100 x
1100 x
1100 x
1100 x
1100 x
1100 x
1100 x
1100 x
1100 x
1100 x
1100 x
1100 x
950
900
850
800
750
700
650
600
550
500
1118
1118
1118
1118
1118
1118
1118
1118
1118
1118
965
914
864
813
762
71 1
660
610
559
508
813
813
813
813
813
813
813
813
813
813
737
724
724
711
711
698
698
698
686
686
46
46
46
46
46
46
46
46
46
46
46
46
x
x
x
x
x
x
x
x
x
x
x
x
46 x
46 x
46 x
46 x
46 x
46 x
46 x
46 x
46 x
46 x
46 x
46 x
44
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1150 x
1100
1050
1000
950
900
850
800
750
700
650
600
550
1168
1168
1168
1168
I168
i168
1168
1168
1168
1168
1168
1168
1118
1067
1016
965
914
864
813
762
71 1
660
610
559
851
851
851
851
851
851
851
851
851
851
851
851
800
787
775
762
762
749
749
737
737
737
724
724
48
48
48
48
48
48
48
48
48
48
48
48
48
x
x
x
x
x
x
x
x
x
x
x
x
x
48 x
48 x
48 x
48 x
48 x
48 x
48 x
48 x
48 x
48 x
48 x
48 x
48 x
46
1200 x
1200 x
1200 x
1200 x
1200 x
1200x
1200 x
1200 x
1200 x
1200x
1200 x
1200 x
1200 x
1200 x 1150
1200 x 1100
1200 x 1050
1200 x 1000
1200 x 950
1200x900
1200 x 850
1200 x 800
1200 x 750
1200x700
1200 x 650
1200 x 600
1200 x 550
1219
1219
1219
1219
1219
1219
1219
1219
1219
1219
1219
1219
1219
1168
1118
1067
1016
965
914
864
813
762
711
660
610
559
889
889
889
889
889
889
889
889
889
889
889
889
889
838
838
ai3
813
813
787
787
787
762
762
762
737
737
42
40
38
36
34
32
30
28
26
24
22
44
42
40
38
36
34
32
30
28
26
24
22
16
ASME 816.9-2001
Note (1)
Note (2)
4T
Enlarged Section
of Lap
DN
Outside Diameter
of Barrel
Max.
Min.
Long Pattern
Length, F
[Notes (31. (411
Short Pattern
Length, F
[Notes (31. (411
Radius of
Fillet, R
[Note (511
Diameter
of Lap, G
[Note (611
15
20
25
32
40
22.8
28.1
35.0
43.6
49.9
20.5
25.9
32.6
41.4
47.5
76
76
102
102
102
51
51
51
51
51
3
3
3
5
6
35
43
51
64
73
50
65
80
90
1O0
62.4
75.3
91.3
104.0
116.7
59.5
72.2
88.1
100.8
113.5
152
152
152
152
152
64
64
64
76
76
8
8
10
10
11
92
106
127
140
157
5
6
8
10
12
125
150
200
250
300
144.3
171.3
222.1
277.2
328.0
140.5
167.5
218.3
272.3
323.1
203
203
203
254
254
76
89
102
127
152
11
13
13
13
13
185
218
270
324
38 1
14
16
18
20
350
400
450
500
359.9
41 1.O
462
514
354.8
405.6
456
507
305
305
305
305
152
152
152
152
13
13
13
13
413
470
533
584
22
24
550
600
565
616
558
609
305
305
152
152
13
13
641
692
'12
74
1
1'/4
1'/2
2
2'12
3
3 '/2
GENERAL NOTES:
(a) All dimensions are i n millimeters.
(b) See Table 2 for tolerances.
(c) Service conditions and joint construction often dictate stub end length requirements. Therefore, the purchaser must specify
long or short pattern fitting when ordering.
NOTES:
(1) Gasket face finish shall be i n accordance with ASME 816.5 for raised face flanges.
(2) The lap thickness Tshall not be less than nominal pipe wall thickness. See Table 2 for maximum tolerance.
(3) When short pattern stub ends are used with larger flanges i n Classes 300 and 600, (PN50 81 PN110) and with most sizes in
Classes 900 (PN150) and higher, and when long pattern stub ends are used with larger flanges in Classes 1500 and 2500,
(PN260 AND PN420) it may be necessary t o increase the length of the stub ends in order t o avoid covering the weld with
the flange. Such increases i n length shall be a matter of agreement between the manufacturer and purchaser.
(4) When special facings such as tongue and groove, male and female, etc., are employed, additional lap thickness must be
provided and such additional thickness shall be i n addition t o (not included in) the basic length F.
(5) These dimensions conform t o the radius established for lap joint flanges in ASME 816.5, Pipe Flanges and Flanged Fittings.
(6) This dimension conforms t o standard machined facings shown i n ASME 816.5. The back face of the lap shall be machined
toconformtothesurface on which it seats. Where ring joint facings are t o be applied, use dimension Kasgiven i n ASME 816.5.
17
ASME 816.9-2001
DN
Outside
Diameter
at Bevel
Length, E
[Note (111
Limiting Wall
Thickness for
length, E
Length, E
[Note (211
1
1'/4
1'/2
15
20
25
32
40
21.3
26.7
33.4
42.2
48.3
25
25
38
38
38
4.57
3.81
4.57
4.83
5.08
25
25
38
38
38
2
2'4
3
3'/2
4
50
65
80
90
1O0
60.3
73.0
88.9
101.6
114.3
38
38
51
64
64
5.59
7.1 1
7.62
8.13
8.64
44
5
8
10
12
125
150
200
250
300
141.3
168.3
219.1
273.0
323.8
76
89
102
127
152
9.65
10.92
12.70
12.70
12.70
89
102
127
152
178
14
16
18
20
22
350
400
450
500
550
355.6
406.4
457
508
559
165
178
203
229
254
12.70
12.70
12.70
12.70
12.70
191
203
229
254
254
24
26
28
30
32
600
650
700
750
800
610
660
711
762
813
267
267
267
267
267
12.70
305
34
36
38
40
42
850
900
950
1O00
1050
864
914
965
1016
1067
267
267
305
305
305
44
1100
1150
1200
1118
1168
1219
343
343
343
52
"/4
46
48
...
...
...
...
...
...
...
...
...
...
...
...
51
64
76
76
...
...
...
...
...
...
...
...
...
...
...
...
GENERAL NOTES:
(a) All dimensions are in millimeters.
b) The shape of these caps shall be elipsoidal and shall conform to the shape requirements
as given in the ASME Boiler and Pressure Vessel Code.
NOTES:
(1) Length applies for thickness not exceeding that given in column "Limiting Wall Thickness
for Length E."
(2) Length El applies for thickness greater than that given in column "Limiting Wall Thickness"
for NPS 24 (DN 600) and smaller. For NPS 26 (DN 65) and larger, length El shall be by
agreement between manufacturer and purchaser.
18
ASME B16.9-2001
Note (1)
Outside
Diameter at
Bevel
Nominal Pipe
Size (NPS)
DN
Large
End
Small
End
20 X
20 X
25 X
25 X
15
10
20
15
26.7
26.7
33.4
33.4
21.3
17.3
26.7
21.3
38
38
51
51
32 X
32 X
32 X
25
20
15
42.2
42.2
42.2
33.4
26.7
21.3
51
51
51
40 X
40 X
40 X
40 X
32
25
20
15
48.3
48.3
48.3
48.3
42.2
33.4
26.7
21.3
50 X
50 X
50 X
50 X
40
32
25
20
60.3
60.3
60.3
60.3
48.3
42.2
33.4
26.7
65 X
65 X
65 X
65 X
80 X
80 X
80 X
80 X
50
40
32
25
65
50
40
32
73.0
73.0
73.0
73.0
88.9
88.9
88.9
88.9
Nominal Pipe
Size (NPSI
End-to-End,
60.3
48.3
42.2
33.4
73.0
60.3
48.3
42.2
64
64
64
64
76
76
76
76
89
89
89
89
89
89
89
89
90 X
90 X
90 X
90 X
90 X
80
65
50
40
32
101.6
101.6
101.6
101.6
101.6
88.9
73.0
60.3
48.3
42.2
102
102
102
102
102
100 X
100 X
100 X
100 X
100 X
90
80
65
50
40
114.3
114.3
114.3
114.3
114.3
101.6
88.9
73.0
60.3
48.3
102
102
102
102
102
DN
Large
End
Small
End
End-to-End,
H
5
5
5
5
5
x 4
3/2
x 3
x 21/2
x 2
125 X
125 X
125 X
125 X
125 X
100
90
80
65
50
141.3
141.3
141.3
141.3
141.3
114.3
101.6
88.9
73.0
60.3
127
127
127
127
127
6
6
6
6
6
x 5
x 4
X 372
x 3
x 2/2
150 X
150 X
150 X
150 X
150 x
125
100
90
80
65
168.3
168.3
168.3
168.3
168.3
141.3
114.3
101.6
88.9
73.0
140
140
140
140
140
8 x 6
8 x 5
8 x 4
8 X 312
200 X
200 X
200 x
200 x
150
125
100
90
219.1
219.1
219.1
219.1
168.3
141.3
114.3
101.6
152
152
152
152
10 X 8
10 X 6
10 x 5
10 x 4
250
250
250
250
200
150
125
100
273.0
273.0
273.0
273.0
219.1
168.3
141.3
114.3
178
178
178
178
12
12
12
12
300
300
300
300
250
200
150
125
323.8
323.8
323.8
323.8
273.0
219.1
168.3
141.3
203
203
203
203
12
10
8
6
350
350
350
350
300
250
200
150
355.6
355.6
355.6
355.6
323.8
273.0
219.1
168.3
330
330
330
330
16 x 14
16 x 12
16 x 10
16 X 8
400
400
400
400
350
300
250
200
406.4
406.4
406.4
406.4
355.6
323.8
273.0
219.1
356
356
356
356
18 X
18 X
18 X
18 X
450
450
450
450
400
350
300
250
457
457
457
457
406.4
355.6
323.8
273.0
381
381
381
38 1
x 10
8
X 6
x 5
X
14 X
14 X
14 X
14 X
16
14
12
10
X
X
X
X
X
X
X
X
X
X
X
X
(contin uedl
19
ASME B16.9-2001
Outside
Diameter at
Bevel
Nominal Pipe
Size (NPS)
Large
End
DN
Small
End
20 X 18
20 X 16
20 X 14
20 x 12
500
500
500
500
x
x
x
x
450
400
350
300
508
508
508
508
457
406.4
355.6
323.8
508
508
508
508
22 x 20
22 X 18
22 X 16
22 X 14
550
550
550
550
x 500
x 450
x 400
X 350
559
559
559
559
508
457
406.4
355.4
508
508
508
508
24 X 22
24 x 20
24 X 18
24 X 16
600
600
600
600
x 550
x 500
x 450
x 400
610
610
610
610
559
508
457
406.4
508
508
508
508
26 X 24
26 X 22
26 x 20
26 X 18
650
650
650
650
x
x
x
x
600
550
500
450
660
660
660
660
61O
559
508
457
610
610
610
61O
28 X 26
28 X 24
28 x 22
28 X 20
700 X
700 x
700 X
700 X
650
600
550
500
711
711
711
711
660
610
457
610
610
61O
610
30 X 28
30 X 26
30 X 24
30 x 22
750 X
750 X
750 X
750 x
700
650
600
550
762
762
762
762
711
660
610
508
610
61O
610
610
32 X 30
32 X 28
32 X 26
32 X 24
800
800
800
800
x 750
X 700
x 650
X 600
813
813
813
813
762
711
660
610
61O
61O
610
610
34 X 32
34 X 30
34 X 28
34 X 26
850
850
850
850
800
750
x 700
X 650
864
864
864
864
813
762
660
610
610
610
610
610
Nominal Pipe
Size NPS1
End-to-End,
H
508
DN
Large
End
Small
End
End-to-End,
H
36
36
36
36
36
x 34
x 32
x 30
X 28
x 26
900 x 850
900 x 800
900 X 750
900 X 700
900 X 650
914
914
914
914
914
864
813
762
660
610
610
610
610
610
610
38
38
38
38
38
38
x 36
x 34
X 32
x 30
x 28
X 26
950 X
950 X
950 X
950 X
950 X
950 X
900
850
800
750
700
650
965
965
965
965
965
965
914
864
813
762
711
660
61O
610
610
610
610
610
40 X 38
40 X 36
40 x 34
40 x 32
40 x 30
1000 X
1000 X
1000 X
1000 X
1000 X
950 1016
900 1016
850 1016
800 1016
750 1016
965
914
864
813
762
61O
610
610
610
61O
1067
1067
1067
1067
1067
1067
1016
965
914
864
813
762
610
610
610
610
61O
61O
44 X 42
44 X 40
44 x 38
44 X 36
1061
1016
965
914
61O
61O
610
610
46 x 44
46 X 42
46 x 40
46 X 38
1118
1067
1016
965
71 1
71 1
71 1
71 1
1200 X
1200 X
1200 X
1200 X
1168
1118
1067
1016
71 1
71 1
71 1
711
42
42
42
42
42
42
48
48
48
48
x 40
X 38
X 36
x 34
X 32
X 30
x
x
x
x
46
44
42
40
1050
1050
1050
1050
1050
1050
X
X
1000
950
900
850
800
750
1150
1100
1050
1000
1219
1219
1219
1219
20
ASME 616.9-2001
MANDATORY APPENDIX I
INCH TABLES
21
COPYRIGHT American Society of Mechanical Engineers
Licensed by Information Handling Services
ASME 816.9-2001
MANDATORY APPENDIX I
u)
ii
.E
Y)
h-k-4
22
COPYRIGHT American Society of Mechanical Engineers
Licensed by Information Handling Services
i.
ASME 816.9-2001
8
W
O
e
"c
o
+ o
d
N
-O
O
c
Lo
cn
Lo
8+ o 8+ o
o
+ o
o
+ o
o9
+ o
o9
+ o
m
o9
+ o
o9
+ o
o9
+ o
o9
+ o
o9
2
ln
2
Lo
9
O
Lo
2
Lo
8
Lo
2
Lo
"!
O
Fi
+ o
ln
Lo
CO
c?
:
:
03
Lo
Lo
Lo
CO
c?
"!
9
O
<D
8
m
8s
+ O
8
m
N
F
-7p
o .
+ o
9
O
E
o
Lo
+ o
O
N
23
0
.
O
e
Y m
s
m
m
O
c
<D
MANDATORY APPENDIX .i
ASME 816.9-2001
Center-to-End
Outside
Diameter
at Bevel
90 Deg
Elbows,
45 Deg
Elbows,
NominaI
Pipe
Size
(NPS)
0.84
1.O5
1.32
1.66
1.50
1.50
1.50
1.88
0.62
0.75
0.88
1.o0
16
18
20
22
16.00
18.00
20.00
22.00
24.00
27.00
30.00
33.00
10.00
11.25
12.50
13.50
2
2/'2
3
1.90
2.38
2.88
3.50
2.25
3.00
3.75
4.50
1.12
1.38
1.75
2.00
24
26
28
30
24.00
26.00
28.00
30.00
36.00
39.00
42.00
45.00
15.00
16.00
17.25.
18.50
3'/2
4
5
6
4.00
4.50
5.56
6.62
5.25
6.00
7.50
9.00
2.25
2.50
3.12
3.75
32
34
36
38
32.00
34.00
36.00
38.00
48.00
51.00
54.00
57.00
19.75
21.00
22.25
23.62
8.62
10.75
12.75
14.00
12.00
15.00
18.00
21.00
5.00
6.25
7.50
8.75
40
42
40.00
42.00
44
44.00
46
48
46.00
48.00
60.00
63.00
66.00
69.00
72.00
24.88
26.00
27.38
28.62
29.88
Nominal
Pipe
Size
(NPS)
'12
y4 [Note ( 1 ) l
1
1'/4
1/'2
8
10
12
14
Outside
Diameter
at Bevel
90 Dag
Elbows,
45 Deg
Elbows,
24
ASME 616.9-2001
MANDATORY APPENDIX I
3 x 2/2
3 x 2
3 x 1/2
8:: : 25;
5
5
5
5
x 4
x 3/2
x 3
x 2/2
8 x 6
8 x 5
8 x 4
Outside Diameter
at Bevel
CentertoEnd,
Nominal
Pipe
Size
(NPSI
Large End
CentertoEnd,
Outside Diameter
at Bevel
Small End
Lame End
Small End
2.38
2.38
2.38
1.90
1.66
1.32
3.00
3.00
3.00
10 x 8
10 x 6
10 x 5
10.75
10.75
10.75
8.62
6.62
5.56
15.00
15.00
15.00
2.88
2.88
2.88
2.38
1.90
1.66
3.75
3.75
3.75
12 x 10
12 X 8
12 x 6
12.75
12.75
12.75
10.75
8.62
6.62
18.00
18.00
18.00
3.50
3.50
3.50
2.88
2.38
1.90
4.50
4.50
4.50
14 x 12
14 x 10
14 X 8
14.00
14.00
14.00
12.75
10.75
8.62
21.00
21.00
21.00
4.00
4.00
4.00
3.50
2.88
2.38
5.25
5.25
5.25
16 x 14
16 X 12
16 x 10
16.00
16.00
16.00
14.00
12.75
10.75
24.00
4.50
4.50
4.50
4.50
4.00
3.50
2.88
2.38
6.00
6.00
6.00
6.00
18 x
18 x
18 x
18 X
16
14
12
10
18.00
18.00
18.00
18.00
16.00
14.00
12.75
10.75
27.00
27.00
27.00
27.00
5.56
5.56
5.56
5.56
4.50
4.00
3.50
2.88
7.50
7.50
7.50
7.50
20 X 18
20 X 16
20 X 14
20 x 12
20.00
20.00
20.00
20.00
18.00
16.00
14.00
12.75
30.00
30.00
30.00
30.00
6.62
6.62
6.62
6.62
5.56
4.50
4.00
3.50
9.00
9.00
9.00
9.00
20
24
24
24
10
22
20
18
20.00
24.00
24.00
24.00
10.75
22.00
20.00
18.00
30.00
36.00
36.00
36.00
8.62
8.62
8.62
6.62
5.56
4.50
12.00
12.00
12.00
24 x 16
24 X 14
24 x 12
24.00
24.00
24.00
16.00
14.00
12.75
36.00
36.00
36.00
25
x
x
x
x
24.00
24.00
MANDATORY APPENDIX I
ASME 616.9-2001
rA1
1
T B .E 15 DIMENSIONS OF SHORT R di1
ELBOWS
Outside
Diameter
at Bevel
Centerto-Center,
O
Nominal
Pipe
Size
Backto-Face,
Outside
Diameter
at
Bevel
CentertoEnd,
0.84
1.05
1.32
1.66
1.90
3.00
3.00
3.00
3.75
4.50
1.88
2.00
2.19
2.75
3.25
1
15%
1'4
2
2'/2
1.32
1.66
1.90
2.38
2.88
1.o0
1.25
1.50
2.00
2.50
2.38
2.88
3.50
4.00
4.50
6.00
7.50
9.00
10.50
12.00
4.19
5.19
6.25
7.25
8.25
3
3'/2
4
3.00
3.40
4.00
5
6
3.50
4.00
4.50
5.56
6.62
5
6
8
10
12
5.56
6.62
8.62
10.75
12.75
15.00
18.00
24.00
30.00
36.00
10.31
12.31
16.31
20.38
24.38
8
10
12
14
16
8.62
10.75
12.75
14.00
16.00
8.00
10.00
12.00
14.00
16.00
14
16
18
20
22
24
14.00
16.00
18.00
20.00
22.00
24.00
42.00
48.00
54.00
60.00
66.00
72.00
28.00
32.00
36.00
40.00
44.00
48.00
18
20
22
24
18.00
20.00
22.00
24.00
18.00
20.00
22.00
24.00
'12
y4[Note (311
1
1
1'/2
26
5.00
6.00
MANDATORY APPENDIX I
ASME 816.9-2001
I
-+1
Outside
Diameter
at
Bevel
Centerto-Center,
O
1
1
1 '/2
2
2'/2
1.32
1.66
1.90
2.38
2.88
2.00
2.50
3.00
4.00
5.00
1.62
2.06
2.44
3.19
3.94
3
3'12
4
5
6
3.50
4.00
4.50
5.56
6.62
6.00
7.00
8.00
10.00
12.00
4.75
5.50
6.25
7.75
9.31
8
10
12
14
16
8.62
10.75
12.75
14.00
16.00
16.00
20.00
24.00
28.00
32.00
12.31
15.38
18.38
21.00
24.00
18
20
22
24
18.00
20.00
22.00
24.00
36.00
40.00
44.00
48.00
27.00
30.00
33.00
36.00
GENERAL NOTES:
(a) All dimensions are i n inches.
(b) Dimension A is equal to one-half of dimension O.
Outlet,
Run,
C
M
[Notes (1) and (211
1
1 '/4
1 '/2
1.00
1.12
1.50
1.88
2.25
1.00
1.12
1.50
1.88
2.25
2
2'/2
3
3'/2
4
2.38
2.88
3.50
4.00
4.50
2.50
3.00
3.38
3.75
4.12
2.50
3.00
3.38
3.75
4.12
5
6
8
10
12
5.56
6.62
8.62
10.75
12.75
4.88
5.62
7.00
8.50
10.00
4.88
5.62
7.00
8.50
10.00
14
16
18
20
22
14.00
16.00
18.00
20.00
22.00
1 1 .o0
12.00
13.50
15.00
16.50
1 1 .o0
12.00
13.50
15.00
16.50
24
26
28
30
32
24.00
26.00
28.00
30.00
32.00
17.00
19.50
20.50
22.00
23.50
17.00
19.50
20.50
22.00
23.50
34
36
38
40
42
34.00
36.00
38.00
40.00
42.00
25.00
26.50
28.00
29.50
30.00
25.00
26.50
28.00
29.50
28.00
44
46
48
44.00
46.00
48.00
32.00
33.50
35.00
30.00
31.50
33.00
"4
Outside
Diameter
at Bevel
0.84
1 .O5
1.32
1.66
1.90
'12
Backto-Face,
Center-to-End
21
MANDATORY APPENDIX I
ASME 816.9-2001
Nominal
Pipe
Size
(NPS)
Center-to-End
Nominal
Pipe
Size
(NPS)
Outlet,
Run
Outlet
Run,
C
0.84
0.84
1.05
1.05
0.68
0.54
0.84
0.68
1.00
1.00
1.12
1.12
1.o0
1.o0
1.12
1.12
1.32
1.32
1.05
0.84
1.50
1.50
1.50
1.50
1.66
1.66
1.66
1.32
1.05
0.84
1.88
1.88
1.88
1.90
1.90
1.90
1.90
1.66
1.32
1.05
0.84
2.38
2.38
2.38
2.38
Outside
Diameter at
Bevel
Center-to-End
Outlet,
Run
Outlet
Run,
C
4
3/2
3
24
~ 2
5.56
5.56
5.56
5.56
5.56
4.50
4.00
3.50
2.88
2.38
4.88
4.88
4.88
4.88
4.88
4.62
4.50
4.38
4.25
4.12
1.88
1.88
1.88
6 x 6 ~ 5
6 X 6 X 4
6 X 6 X 3/2
6 x 6 ~ 3
6 X 6 X 24
6.62
6.62
6.62
6.62
6.62
5.56
4.50
4.00
3.50
2.88
5.62
5.62
5.62
5.62
5.62
5.38
5.12
5.00
4.88
4.75
2.25
2.25
2.25
2.25
2.25
2.25
2.25
2.25
8
8
8
8
~ 6
~ 5
~ 4
31/2
8.62
8.62
8.62
8.62
6.62
5.56
4.50
4.00
7.00
7.00
7.00
7.00
6.62
6.38
6.12
6.00
1.90
1.66
1.32
1.05
2.50
2.50
2.50
2.50
2.38
2.25
2.00
1.75
10 x
10 x
10 x
10 x
10
10
10
10
x 8
x 6
x 5
x 4
10.75
10.75
10.75
10.75
8.62
6.62
5.56
4.50
8.50
8.50
8.50
8.50
8.00
7.62
7.50
7.25
2.88
2.88
2.88
2.88
2.38
1.90
1.66
1.32
3.00
3.00
3.00
3.00
2.75
2.62
2.50
2.25
12 x
12 x
12 x
12 x
12 x
12 x
12 x
12 x
10
8
6
5
12.75
12.75
12.75
12.75
10.75
8.62
6.62
5.56
10.00
10.00
10.00
10.00
9.50
9.00
8.62
8.50
3 x 3 x 24
3 X 3 X 2
3 x 3 x 1v2
3x 3x
3.50
3.50
3.50
3.50
2.88
2.38
1.90
1.66
3.38
3.38
3.38
3.38
3.25
3.00
2.88
2.75
14 X
14 X
14 X
14 x
14 X
14 X
14 X
14 x
12
10
8
6
14.00
14.00
14.00
14.00
12.75
10.75
8.62
6.62
11.00
11.00
11.00
11.00
10.62
10.12
9.75
9.38
3/2
3Y2
3/2
312
3/2 X 3
312 X 2/2
X 3/2 X 2
X 312 X 11/2
4.00
4.00
4.00
4.00
3.50
2.88
2.38
1.90
3.75
3.75
3.75
3.75
3.62
3.50
3.25
3.12
16 x
16 x
16 x
16 x
16 x
16
16
16
16
16
x
x
x
x
x
14
12
10
8
6
16.00
16.00
16.00
16.00
16.00
14.00
12.75
10.75
8.62
6.62
12.00
12.00
12.00
12.00
12.00
12.00
11.62
11.12
10.75
10.38
4X
4 X
4 x
4 X
4x
4
4
4
4
4
4.50
4.50
4.50
4.50
4.50
4.00
3.50
2.88
2.38
1.90
4.12
4.12
4.12
4.12
4.12
4.00
3.88
3.75
3.50
3.38
18 x
18 x
18 x
18 x
18 X
18
18
18
18
18
x 16
x 14
x 12
x 10
X 8
18.00
18.00
18.00
18.00
18.00
16.00
14.00
12.75
10.75
8.62
13.50
13.50
13.50
13.50
13.50
13.00
13.00
12.62
12.12
11.75
4 x
/2
12
Y4
x
x
Y4
Y4
/2
Y4
x
x
x
x
Ya
/4
Y2
Ya
1 X l X Y 4
1x 1x
I/~
1/4
1/4
x
x 1
x 1Y4 x Y4
x 114 x /2
1/2 x
1/2
l/q
1/2
x 1/2 x 1
x 1/2 x 74
1/2
x 14 x
1/2
2X2XlY2
2 x 2 x 15%
2 X 2 X 1
2X2XY4
212
21/2
272
24
x 2Y2 x 2
212 X 11/2
X 2/2 X
x 2/2 x 1
X
X 3/2
X 3
x 2v2
X 2
x 172
[Note (111
5
5
5
5
5
X 5 X
5X
X 5 X
x 5x
x 5
x 8
x 8
x 8
x 8 x
[Note (111
28
Outside
Diameter at
Bevel
Run
Outlet
Center-to-End
Outlet,
Run,
C
M
[Note II))
Outside
Diameter at
Bevel
Nominal
Pipe
Size
INPS)
Run
Outlet
Center-to-End
Outlet,
M
Run,
C
[Note Il)]
18
16
14
12
10
8
20.00
20.00
20.00
20.00
20.00
20.00
18.00
16.00
14.00
12.75
10.75
8.62
15.00
15.00
15.00
15.00
15.00
15.00
14.50
14.00
14.00
13.62
13.12
12.75
32 X
32 x
32 X
32 x
32 x
32 X
32 X
32 x
32 X
32 x
32 x
32 X
24
22
20
18
16
14
32.00
32.00
32.00
32.00
32.00
32.00
24.00
22.00
20.00
18.00
16.00
14.00
23.50
23.50
23.50
23.50
23.50
23.50
22.00
21.50
21.00
20.50
20.00
20.00
x 22 x 20
x 22 x 18
x 22 x 16
X 22 X 14
x 22 x 12
x 22 x 10
22.00
22.00
22.00
22.00
22.00
22.00
20.00
18.00
16.00
14.00
12.75
10.75
16.50
16.50
16.50
16.50
16.50
16.50
16.00
15.50
15.00
15.00
14.62
14.12
24 x 24 x 22
24 X 24 X 20
24 X 24 X 18
24 x 24 x 16
24 X 24 X 14
24 X 24 X 12
24 X 24 X 10
24.00
24.00
24.00
24.00
24.00
24.00
24.00
22.00
20.00
18.00
16.00
14.00
12.75
10.75
17.00
17.00
17.00
17.00
17.00
17.00
17.00
17.00
17.00
16.50
16.00
16.00
15.62
15.12
34 x
34 x
34 X
34 x
34 X
34 x
34 x
34 x
34 X
34 x
34 x
34 X
34 x
34 X
34 x
34 x
34 x
34 X
32
30
28
26
24
22
20
18
16
34.00
34.00
34.00
34.00
34.00
34.00
34.00
34.00
34.00
32.00
30.00
28.00
26.00
24.00
22.00
20.00
18.00
16.00
25.00
25.00
25.00
25.00
25.00
25.00
25.00
25.00
25.00
24.50
24.00
23.50
23.50
23.00
22.50
22.00
21.50
21.00
26 X 26 X
26 X 26 X
26 X 26 X
26 x 26 x
26 X 26 X
26 X 26 X
26 x 26 x
24
22
20
18
16
14
12
26.00
26.00
26.00
26.00
26.00
26.00
26.00
24.00
22.00
20.00
18.00
16.00
14.00
12.75
19.50
19.50
19.50
19.50
19.50
19.50
19.50
19.00
18.50
18.00
17.50
17.00
17.00
16.62
36 x 36 x 34
36 X 36 X 32
36 X 36 X 30
36 X 36 X 28
36 X 36 X 26
36 X 36 X 24
36 x 36 x 22
36 X 36 X 20
36 x 36 x 18
36 X 36 X 16
36.00
36.00
36.00
36.00
36.00
36.00
36.00
36.00
36.00
36.00
34.00
32.00
30.00
28.00
26.00
24.00
22.00
20.00
18.00
16.00
26.50
26.50
26.50
26.50
26.50
26.50
26.50
26.50
26.50
26.50
26.00
25.50
25.00
24.50
24.50
24.00
23.50
23.00
22.50
22.00
x 26
X 24
X 22
x 20
x 18
x 16
x 14
x 12
28.00
28.00
28.00
28.00
28.00
28.00
28.00
28.00
26.00
24.00
22.00
20.00
18.00
16.00
14.00
12.75
20.50
20.50
20.50
20.50
20.50
20.50
20.50
20.50
20.50
20.00
19.50
19.00
18.50
18.00
18.00
17.62
28
26
24
22
20
18
16
14
12
10
30.00
30.00
30.00
30.00
30.00
30.00
30.00
30.00
30.00
30.00
28.00
26.00
24.00
22.00
20.00
18.00
16.00
14.00
12.75
10.75
22.00
22.00
22.00
22.00
22.00
22.00
22.00
22.00
22.00
22.00
21.50
21.50
21.00
20.50
20.00
19.50
19.00
19.00
18.62
18.12
32 x 32 x 30
32 x 32 x 28
32 x 32 x 26
32.00
32.00
32.00
30.00
28.00
26.00
23.50
23.50
23.50
23.00
22.50
22.50
20 X
20 x
20 X
20 x
20 x
20 x
ASME 816.9-2001
MANDATORY APPENDIX I
22
22
22
22
22
22
28
28
28
28
28
28
28
28
20 X
20 x
20 X
20 x
20 x
20 x
x 28
X 28
X 28
x 28
x 28
x 28
x 28
x 28
30 x
30 x
30 x
30 x
30 x
30 x
30 x
30 x
30 x
30 x
30 x
30 x
30 x
30 x
30 x
30 x
30 x
30 x
30 x
30 x
38 X
38 x
38 X
38 X
38 X
38 x
38 X
38 x
38 X
38 x
38 X
38 x
38 X
38 X
38 X
38 x
38 X
38 x
38 X
38 x
36
34
32
30
28
26
24
22
20
18
38.00
38.00
38.00
38.00
38.00
38.00
38.00
38.00
38.00
38.00
36.00
34.00
32.00
30.00
28.00
26.00
24.00
22.00
20.00
18.00
28.00
28.00
28.00
28.00
28.00
28.00
28.00
28.00
28.00
28.00
28.00
27.50
27.00
26.50
25.50
25.50
25.00
24.50
24.00
23.50
40 X
40 x
40 x
40 x
40 X
40 x
40 x
40 x
40 x
40 X
40 x
40 X
40 x
40 x
40 x
40 X
40 x
40 x
40 x
40 x
40 X
40 x
38
36
34
32
30
28
26
24
22
20
18
40.00
40.00
40.00
40.00
40.00
40.00
40.00
40.00
40.00
40.00
40.00
38.00
36.00
34.00
32.00
30.00
28.00
26.00
24.00
22.00
20.00
18.00
29.50
29.50
29.50
29.50
29.50
29.50
29.50
29.50
29.50
29.50
29.50
29.50
29.00
28.50
28.00
27.50
26.50
26.50
26.00
25.50
25.00
24.50
42 x 42 x 40
40 X 40 X 38
42.00
42.00
40.00
38.00
30.00
30.00
28.00
28.00
(continued)
29
NominaI
Pipe
Sire
(NPS)
42
42
42
42
42
42
42
42
42
42
42
42
42
x 42
X 42
X 42
X 42
X 42
X 42
X 42
X 42
X 42
X
x
X
X
X
X
X
X
X
X
36
34
32
30
28
26
24
22
20
18
16
44 X 44 X 42
44 X 44 X 40
44X44X38
4 4 x 4 4 ~ 3 6
44 x 44 x 34
44X44X32
44 X 44 X 30
44 X 44 X 28
44X44X26
44 X 44 X 24
44 x 44 x 22
44 x 44 x 20
Outside
Diameter at
Bevel
Center-to-End
Run
Outlet
Run,
C
42.00
42.00
42.00
42.00
42.00
42.00
42.00
42.00
42.00
42.00
42.00
36.00
34.00
32.00
30.00
28.00
26.00
24.00
22.00
20.00
18.00
16.00
30.00
30.00
30.00
30.00
30.00
30.00
30.00
30.00
30.00
30.00
30.00
28.00
28.00
28.00
28.00
27.50
27.50
26.00
26.00
26.00
25.50
25.00
44.00
44.00
44.00
44.00
44.00
42.00
40.00
38.00
36.00
34.00
32.00
30.00
28.00
26.00
24.00
22.00
20.00
32.00
32.00
32.00
32.00
32.00
32.00
32.00
32.00
32.00
32.00
32.00
32.00
30.00
29.50
29.00
28.50
28.50
28.00
28.00
27.50
27.50
27.50
27.00
27.00
44.00
44.00
44.00
44.00
44.00
44.00
44.00
Nominal
Pipe
Sire
(NI'S)
Outlet,
[Note (111
Outlet
44
42
40
38
36
34
32
30
28
26
24
22
46.00
46.00
46.00
46.00
46.00
46.00
46.00
46.00
46.00
46.00
46.00
46.00
44.00
48
48
48
48
48
48
48
48
48
48
48
48
48
X 48 X 46
x 48 x 44
x 48 x 42
x 48 x 40
X 48 X 38
X 48 X 36
X 48 X 34
X 48 X 32
X 48 X 30
X 48 X 28
X 48 X 26
x 48 x 24
X 48 X 22
48.00
48.00
48.00
48.00
48.00
48.00
48.00
48.00
48.00
48.00
48.00
48.00
48.00
46.00
x
X
X
X
X
X
x
x
X
X
X
X
x
X
X
X
X
X
x
x
X
~~
30
Run
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
46
Outside
Diameter at
Bevel
42.00
40.00
38.00
36.00
34.00
32.00
30.00
28.00
26.00
24.00
22.00
44.00
42.00
40.00
38.00
36.00
34.00
32.00
30.00
28.00
26.00
24.00
22.00
Center-to-End
Outlet,
Run,
C
[Note (111
33.50
33.50
33.50
33.50
33.50
33.50
33.50
33.50
33.50
33.50
33.50
33.50
31.50
31.00
30.50
30.00
30.00
29.50
29.50
29.00
29.00
29.00
28.50
28.50
35.00
35.00
35.00
35.00
35.00
35.00
35.00
35.00
35.00
35.00
35.00
35.00
35.00
33.00
33.00
32.00
32.00
32.00
31.00
31.00
31.00
30.00
30.00
30.00
29.00
29.00
ASME 616.9-2001
MANDATORY APPENDIX I
Note square
corner
Note (1)
4T k -
Note (2)
Enlarged Section
of Lap
Diameter
Short Pattern
Length, F
[Notes-(3), (411
Radius of
Fillet, R
[Note (511
of Lap, G
[Note (611
Min.
1
1
1 '/2
0.896
1.106
1.376
1.716
1.965
0.809
1.019
1.284
1.629
1.869
3.00
3.00
4.00
4.00
4.00
2.00
2.00
2.00
2.00
2.00
0.12
0.12
0.12
0.19
0.25
1.38
1.38
2.00
2.50
2.88
2
2'/2
3
3'/*
4
2.456
2.966
3.596
4.096
4.593
2.344
2.844
3.469
3.969
4.469
6.00
6.00
6.00
6.00
6.00
2.50
2.50
2.50
3.00
3.00
0.31
0.31
0.38
0.38
0.44
3.62
4.12
5.00
5.50
5.19
5
6
8
10
12
5.683
6.743
8.743
10.913
12.913
5.532
6.594
8.594
10.719
12.719
8.00
8.00
8.00
10.00
10.00
3.00
3.50
4.00
5.00
6.00
0.44
0.50
0.50
0.50
0.50
7.31
8.50
10.62
12.75
15.00
14
16
18
20
22
24
14.170
16.180
18.190
20.240
22.240
24.240
13.969
15.969
17.969
19.969
21.969
23.969
12.00
12.00
12.00
12.00
12.00
12.00
6.00
6.00
6.00
6.00
6.00
6.00
0.50
0.50
0.50
0.50
0.50
0.50
16.25
18.50
21.00
23.00
25.25
27.25
'12
Long Pattern
Length, F
iNotes-(3), (411
Max.
Outside Diameter
of Barrel
GENERAL NOTES:
(a) All dimensions are i n inches.
(b) See Table Il for tolerances.
(cl Service conditions and joint construction oten dictate stub end length requirements. Therefore, the purchaser must specify
long or short pattern fitting when ordering.
NOTES:
(1)Gasket face finish shall be i n accordance with ASME 816.5for raised face flanges.
(2)The lap thickness Tshall not be less than nominal pipe wall thickness. See Table Il for tolerance.
(3)When short pattern stub ends are used with larger flanges in Classes 300 and 600,and with most sizes in Classes 900 and
higher, and when long pattern stub ends are used with larger flanges in Classes 1500 and 2500, it may be necessary t o
increase the length of the stub ends i n order to avoid covering the weld with the flange. Such increases in length shall be
a matter of agreement between the manufacturer and the purchaser.
(4)When special facings such as tongue and groove, male and female, etc., are employed, additional lap thickness must be
provided and such additional thickness shall be in addition to (not included in) the basic length i.
(5) These dimensions conform t o the radius established for lap joint flanges in ASME 616.5,Pipe Flanges and FlaBged Fittings.
(6)This dimension conforms t o standard machine facings shown i n ASME 616.5.The back face of the lap shall be machined
t o conform t o the surface on which it seats. Where ring joint facings are t o beapplied, use dimension Kasgiven in ASME 816.5.
31
ASME 616.9-2001
MANDATORY APPENDIX I
Length, E7
[Note (211
1
1114
1112
0.84
1.05
1.32
1.66
1.90
1.o0
1.o0
1.50
1.50
1.50
0.18
0.15
0.18
0.19
0.20
1.o0
1.o0
1.50
1.50
1.50
2
2'/2
3
3'12
4
2.38
2.88
3.50
4.00
4.50
1.50
1.50
2.00
2.50
2.50
0.22
0.28
0.30
0.32
0.34
1.75
2.00
2.50
3.00
3.00
5.56
6.62
8.62
10.75
12.75
3.00
3.50
4.00
5.00
6.00
0.38
0.43
0.50
0.50
0.50
3.50
4.00
5.00
6.00
7.00
'12
3/4
5
6
8
10
12
14
16
14.00
16.00
6.50
7.00
0.50
0.50
NominaI
Pipe
Outside
Size
Diameter Length, E
(NPS)
at Bevel [Note (111
7.50
8.00
Limiting Wall
Thickness for
Length E
18
20
22
18.00
20.00
22.00
8.00
9.00
10.00
0.50
0.50
0.50
24
26
28
30
32
24.00
26.00
28.00
30.00
32.00
10.50
10.50
10.50
10.50
10.50
0.50
34
36
38
40
42
34.00
36.00
38.00
40.00
42.00
10.50
10.50
12.00
12.00
12.00
44
46
48
44.00
13.50
13.50
13.50
46.00
48.00
...
...
...
...
...
...
...
...
...
...
...
...
Length, 4
[Note (211
9.00
10.00
10.00
12.00
...
...
...
...
...
...
...
...
...
...
...
...
GENERAL NOTES:
(a) All dimensions are i n inches.
(b) The shape of these caps shall be ellipsoidal and shall conform to the shape requirements asgiven in the ASME Boiler and
Pressure Vessel Code.
NOTES:
(1) Length E applies for thickness not exceeding that given in column "Limiting Wall Thickness for Length E."
(2) Length El applies for thickness greater than that given in column "Limiting Wall Thickness" for NPS 24 and smaller. For
NPS 26 and larger, length El shall be by agreement between the manufacturer and purchaser.
32
ASME 616.9-2001
MANDATORY APPENDIX I
Note (1)
74
x 12
x 34
1 x 74
1 x 12
IV4
x 1
x 34
1/4
154 x
52
x 114
1% x 1
172
Outside Diameter
at Bevel
Large
End
Small
End
End-to-End,
1.O5
1.O5
1.32
1.32
0.84
0.68
1.05
0.84
1.50
1.50
2.00
2.00
1.66
1.66
1.66
1.32
1.O5
0.84
2.00
2.00
2.00
1.90
1.90
1.90
1.90
1.66
1.32
1.O5
0.84
2.50
2.50
2.50
2.50
2.38
2.38
2.38
2.38
1.90
1.66
1.32
1.O5
3.00
3.00
3.00
3.00
2.88
2.88
2.88
2.88
2.38
1.90
1.66
1.32
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
2.88
2.38
1.90
1.66
3.50
3.50
3.50
3.50
4.00
4.00
4.00
4.00
4.00
3.50
2.88
2.38
1.90
1.66
4.00
4.00
4.00
4.00
4.00
4.50
4.50
4.50
4.50
4.50
4.00
3.50
2.88
2.38
1.90
4.00
4.00
4.00
4.00
4.00
5.56
5.56
4.50
4.00
5.00
5.00
Nominal
Pipe Size
(NPS)
Outside Diameter
at Bevel
Large
End
Small
End
End-to-End,
H
5 x 3
5 x 2/2
5 x 2
5.56
5.56
5.56
3.50
2.88
2.38
5.00
5.00
5.00
6
6
6
6
6
x 5
x 4
X 3/2
x 3
X 2/2
6.62
6.62
6.62
6.62
6.62
5.56
4.50
4.00
3.50
2.88
5.50
5.50
5.50
5.50
5.50
8
8
8
8
x 6
x 5
x 4
X 3l,$
8.62
8.62
8.62
8.62
6.62
5.56
4.50
4.00
6.00
6.00
6.00
6.00
10 X
10 X
10 x
10 x
8
6
5
4
10.75
10.75
10.75
10.75
8.62
6.62
5.56
4.50
7.00
7.00
7.00
7.00
12 x
12 X
12 X
12 x
10
8
6
5
12.75
12.75
12.75
12.75
10.75
8.62
6.62
5.56
8.00
8.00
8.00
8.00
14 X
14 X
14 X
14 X
12
10
8
6
14.00
14.00
14.00
14.00
12.75
10.75
8.62
6.62
13.00
13.00
13.00
13.00
16 X
16 X
16 X
16 X
14
12
10
8
16.00
16.00
16.00
16.00
14.00
12.75
10.75
8.62
14.00
14.00
14.00
14.00
18 X
78 X
18 X
18 X
16
14
12
10
18.00
18.00
18.00
18.00
16.00
74.00
12.75
10.75
15.00
15.00
15.00
15.00
20
20
20
18
16
14
20.00
20.00
20.00
18.00
16.00
14.00
20.00
20.00
20.00
-~
X
X
X
~~
(continued)
33
MANDATORY APPENDIX I
ASME 816.9-2001
Outside Diameter
at Bevel
Large
End
Small
End
End-to-End,
20 x 12
20.00
12.75
20.00
22 x 20
22 X 18
22 x 16
22 X 14
22.00
22.00
22.00
22.00
20.00
18.00
16.00
14.00
20.00
20.00
20.00
20.00
24
24
24
24
x 22
X 20
X 18
x 16
24.00
24.00
24.00
24.00
22.00
20.00
18.00
16.00
20.00
20.00
20.00
20.00
26
26
26
26
24
X 22
X 20
X 18
26.00
26.00
26.00
26.00
24.00
22.00
20.00
18.00
24.00
24.00
24.00
24.00
28
28
28
28
26
24
x 20
X 18
28.00
28.00
28.00
28.00
26.00
24.00
20.00
18.00
24.00
24.00
24.00
24.00
30
30
30
30
x 28
x 26
X 24
x 20
30.00
30.00
30.00
30.00
28.00
26.00
24.00
20.00
24.00
24.00
24.00
24.00
32
32
32
32
30
x 28
X 26
X 24
32.00
32.00
32.00
32.00
30.00
28.00
26.00
24.00
24.00
24.00
24.00
24.00
34
34
34
34
x 32
30
26
x 24
34.00
34.00
34.00
34.00
32.00
30.00
26.00
24.00
24.00
24.00
24.00
24.00
36 x 34
36 x 32
36.00
36.00
34.00
32.00
Nominal
Pipe Size
(NPS)
Large
End
Small
End
End-to-End.
36 X 30
36 X 26
36 X 24
36.00
36.00
36.00
30.00
26.00
24.00
24.00
24.00
24.00
38
38
38
38
38
38
36
34
32
30
28
26
38.00
38.00
38.00
38.00
38.00
38.00
36.00
34.00
32.00
30.00
28.00
26.00
24.00
24.00
24.00
24.00
24.00
24.00
40
40
40
40
40
38
X 32
X 30
40.00
40.00
40.00
40.00
40.00
38.00
36.00
34.00
32.00
30.00
24.00
24.00
24.00
24.00
24.00
42
42
42
42
42
42
40
38
36
34
32
30
42.00
42.00
42.00
42.00
42.00
42.00
40.00
38.00
36.00
34.00
32.00
30.00
24.00
24.00
24.00
24.00
24.00
24.00
44 X 42
44 X 40
44.00
44 X 38
44 X 36
44.00
44.00
42.00
40.00
38.00
36.00
24.00
24.00
24.00
24.00
46
46
46
46
46.00
46.00
46.00
46.00
44.00
42.00
40.00
38.00
28.00
28.00
28.00
28.00
48.00
48.00
48.00
48.00
46.00
44.00
42.00
40.00
28.00
28.00
28.00
48
48
48
48
24.00
24.00
Outside Diameter
at Bevel
x
X
X 36
X
X
X
X
X
34
44
X 42
X
40
X 38
X
46
X 44
X 42
X
40
44.00
28.00
~~
GENERAL NOTES:
(a) All dimensions are in inches.
NOTE:
(1) While the figure illustrates a "bell shaped" reducer, the use of conical reducer is not prohibited.
34
ASME 816.9-2001
MANDATORY APPENDIX II
REFERENCES
35
ASME 816.9-2001
NONMANDATORY APPENDIX A
QUALITY SYSTEM PROGRAM
36