Académique Documents
Professionnel Documents
Culture Documents
Page
SPECIFICATIONS
11
SPARE PARTS
18
STARK MFG.
9385 N.W. 13 St. Miami .FL33172.
Phone: +1-786-314.7036
www.starkmf.com
info@starkmf.com
SPECIFICATIONS
3-160-72 ELECTRIC
CAPACITY
3-160-72 DIESEL
7.200 Lt / min
(255 cfm)
PRESSURE
1 2 bar.
CYLINDERS
3 X 160 mm.
PISTON STROKE
80 mm.
ENGINE / MOTOR
18,5 Kw
1500 rpm
electric motor.
Deutz FL 4 912
4 cylinder
80 hp diesel engine.
DIMENTIONS
1150x1580x750 mm
1150x2230x1118 mm
WEIGHT
460 Kg
740 Kg
OPERATION AND
MAINTENANCE
(spanish version)
1 - PARA COMENZAR
Se debe chequear los tornillos del crter a los 45 das de haber puesto en marcha
el equipo por primera vez
Se debe chequear las vlvulas de inyeccin y extraccin a los 90 das despus de
la primera puesta en marcha
Se debe chequear los tornillos de los cilindros del soplador 90 das despus de la
primera puesta en macha del equipo
No cambiar las revoluciones del motor. Deben siempre estar a 1500 rpm.
Inspeccionar que la vlvula anti retorno del Trailer funcione correctamente.
2-
3-
TIPO DE CONEXIN
Fase
Fase
Fase
Tierra
Tabla Nro. 1. Tabla de conductores.
4-
TABLA DE AYUDA
FALLAS
Mantenimiento y cambios en
casos de prdidas de presin
en la salida de la tubera
Mantenimientos y cambios en
caso que suba la presin en la
salida de la tubera.
CAUSAS
RECOMENDACIONES
Chequear el filtro.
Lo ms importante, reemplace el
aceite que perdi propiedad.
Ruptura de hlice.
Vibracin o detonaciones
ocurren en el soplador.
Se activa antes de
tiempo,
Si est goteando,
Si no abre o no libera
aire.
A . Apriete suavemente el
mecanismo de resorte.
B . Reemplace por uno nuevo.
10
OVERHAULING MANUAL
11
A)
12
6. Remove the piston rings from the pistons using the dedicated piston
ring tool.
7. Air Valves (suction and pressure valves) can be removed from the
head and conduct function test on them to ensure they are working
sufficiently. If not they should be replaced.
13
2. Install the crankshaft on the block and fix the front and rear cover,
make sure the crankshaft bearings are in good condition and there is no
unusual noise coming from them.
3. Install the pistons on the connecting rods and fix the piston pins.
4. Install the piston rings on the piston using the ring special tool, oil ring
at the bottom, compression ring is in the middle and on top, make sure
the writing and letters surface of the rings to face the top position on the
pistons. The space of the rings ( end of the rings ) should be positioned in
different directions and should not be lined in same position.
14
5. Install the sleeve lower O-ring seal at the bottom of the sleeve
(cylinder) and install the sleeve on the pistons.
6. Place the washers below the nuts and tighten the nuts of the
sleeves at equal range with balance to 8 KG torque.
7. Install the valves (suction and pressure valves) on the
compressor head.
15
8. Place the top O-ring seal of the sleeve and compressor head gasket.
9. Install the compressor head on the cylinder carefully, place the
washers under the nuts and tighten the nuts at equal range with
balance to 10 KG torque.
10. Fill the compressor with new oil 20/50 Diesel engine oil, 2.5 litre.
11. Install the other parts of the compressor such as suction manifold
and ensure their gasket in good condition.
16
17
SPARE PARTS
19
20
21
22
STARK MFG.
9385 N.W. 13 St. Miami .FL33172.
Phone: +1-786-314.7036
www.starkmf.com
info@starkmf.com