Académique Documents
Professionnel Documents
Culture Documents
www.elsevier.com/locate/jconhyd
a
Department of Geology, Laval University, Quebec City, Quebec, Canada G1K 7P4
INRS-Eau, Terre et Environnement, Institut National de la Recherche Scientifique, 880 Chemin Sainte-Foy,
Bureau 840, C.P. 7500 Sainte-Foy, Quebec, Canada G1V 4C7
c
Department of Earth Sciences, University of Waterloo, Waterloo, Ontario, Canada N2L 4GI
Abstract
Water quality in the unsaturated and saturated zones of a waste rock pile containing sulphides was
investigated. The main objectives of the project were (1) the evaluation of geochemical trends
including the acid mine drainage (AMD)-buffering mechanism and the role of secondary minerals,
and (2) the investigation of the use of stable isotopes for the interpretation of physical and
geochemical processes in waste rock. Pore water in unsaturated zone was sampled from suction
lysimeters and with piezometers in underlying saturated rocks. The investigation revealed strong
temporal (dry period vs. recharge period), and spatial (slope vs. central region of pile) variability in
the formation of acid mine drainage. The main secondary minerals observed were gypsum and
jarosite. There was a higher concentration of gypsum in solid phase at Site TBT than at Site 6,
suggesting that part of the gypsum formed at Site 6 in the early stage of AMD has been already
dissolved. Formation of secondary minerals contributed to the formation of AMD by opening of
foliation planes in waste rock, thus increasing the access of oxidants like O2 and Fe3 + to previously
encapsulated pyrite. The behavior of several dissolved species such as Mg, Al, and Fe2 + can be
considered as conservative in the leachate. Stable isotopes, deuterium and 18O, indicated internal
46
evaporation within the pile, and were used to trace recharge pulses from snowmelt. Isotope trends for
34
S and 18O(SO4) indicated a lack of sulfate reduction and zones of active oxidation of pyrite,
respectively. Results of numerical modeling of pyrite oxidation and gas and water transport were
consistent with geochemical and isotopic trends and confirmed zones of high evaporation rate within
the rock pile close to the slope. The results indicate that physical and chemical processes within the
pile are strongly coupled and cannot be considered separately when oxidation rates are high and
influence gas transport as a result of heat generation.
D 2003 Elsevier B.V. All rights reserved.
Keywords: Acid mine drainage; Waste rock pile; Geochemistry; Stable isotopes; Internal evaporation; Transport
modeling
1. Introduction
Acid mine drainage (AMD) represents significant environmental and financial
liability for the mining industry. It is caused by the oxidation of sulfides in mine
waste with resulting acidic conditions and mobilization of metals. There are two types
of mine waste. Mine tailings are the final product of ore treatment or processing and
are composed of sand and silt size particles. Waste rock is the non-economic material
removed from a mine to access the ore body. Particle size is generally large,
depending on the mechanical properties of the rock, and on the type of blasting
operation.
The AMD production in mine tailings has been studied extensively, for example by
Dubrovsky et al. (1985), Morin et al. (1988), and Blowes et al. (1991). In contrast,
much less is known about AMD generation from waste rock. Several waste rock
studies have evaluated temperature and gas concentration profiles (Harries and Ritchie,
1985; Lefebvre et al., 1993, 2001; Kuo and Ritchie, 1999). These studies revealed a
significant role of air convection in the unsaturated zone of very reactive waste rock
piles. However, the geochemical environment within waste rock piles is less well
known. Until recently, the focus on waste rock geochemical studies has been on the
quality of drainage water flowing out of the waste rock base (Morin et al., 1994). This
type of monitoring represents an integral over space and time of the acid drainage
produced in various parts of the dump. However, this information does not provide a
clear picture of geochemical processes within the pile (Ritchie, 1994). There have
been attempts to obtain data on water chemistry within the unsaturated zone of waste
rock piles (Shafer et al., 1994), but they were not very successful because of low
water content and correspondingly high suction values characteristic of semiarid
climate conditions in the Northwest USA. The acquisition of geochemical data from
the unsaturated zone of a waste rock pile remains a topic of on-going research (for
example, Smith et al., 1995; Stockwell et al., 2001). Our approach to the assessment
of water quality within waste rock deposits was based on sampling of leachate from
both unsaturated and saturated zones within the pile, combined with transport and
geochemical modeling, and solid phase analysis.
47
2. Site description
The study site is located between Rouyn-Noranda and Val dOr in Abitibi, Quebec,
Canada (Fig. 1). The Mine Doyon is a gold mine that has been operating since 1978.
Initially, open pit mining was conducted with two pits excavated along the strike of the ore
body. Mining operations have been underground since 1989. Most of the excavated waste
rock exists in the South Dump covering an area of more than 50 ha and a volume of about
11.5 million m3 (Gelinas et al., 1994). More than half of this volume consists of sericite
schist, which is the host rock of the ore body. The height of local relief of the pile is 30 35
m between the highest points and the level of drainage ditches (Fig. 2). The AMD
production in the South Dump became apparent 2 years after the construction of the pile
and since 1988 the acid production appears to have attained steady state.
The sericite schist is the main contributor to acid generation. This rock type contains
more than 7% pyrite, generally distributed along schistosity planes. This rock occurs at
Site 6 and Site 7 in the southern part of the pile (Fig. 2). The northwest and central zones
of the pile contain low-grade ore associated with diorite at the top of the pile (a 5-m-thick
layer) at Site TBT (Fig. 2).
Acid drainage from the pile is discharged at the toe because the permeability of the
underlying rocks is very low. The effluent is pumped to a water treatment plant, where the
acidity is neutralized and heavy metals are precipitated. High-density sludge is stored in
special basins and the effluent is released to the Bousquet river in the proximity of the pile.
The south pile was studied by researchers from Laval University from 1990 to 1996
(Gelinas et al., 1992). There was drilling and instrumentation of seven boreholes through
48
the entire thickness of the pile and in the upper part of the underlying rocks. The boreholes
were instrumented for multilevel sampling of gas and measurement of temperature in the
unsaturated zone, and for sampling of water in the saturated zone. Gravity drainage
lysimeters were also installed in the unsaturated zone, allowing sampling down to a depth
of about 4.0 m. Periodic sampling of water in ditches around the pile was also conducted.
Maximum temperatures in the profiles within the pile ranged from 45 to 70 jC.
Lefebvre et al. (1993), used temperature data to derive thermal properties of waste rock
and to determine the pyrite oxidation rate (POR) using 1-D analytical models. That
49
investigation revealed an important role for air convection within the pile. There is a high
convection zone with upward air flow component adjacent to the slope and in the upper
part of the pile and low convection or diffusion zones at the lower elevations within and far
from the edges of the pile. Lefebvre (1994) modeled the AMD generation in the pile using
the non-isothermal multiphase flow model TOUGH AMD expanded from the code
TOUGH2 (Pruess, 1991).
This study focused on geochemical aspects of the AMD behavior with the following
main objectives: (1) characterization of pore water chemistry in the unsaturated zone
including determination of the main geochemical processes, and identification of the
AMD-buffering mechanisms, mineralogical transformations, and role of secondary minerals, and (2) assessment of the potential of stable isotopes for the investigation of AMD.
50
Selected samples were observed under Scanning Electron Microscopy (SEM), with
emphasis placed on detection of secondary minerals. Drill cuttings were observed in
secondary electron mode (SE), using a JEOL 840-A microscope with EDX attachment
capable of light elements analysis. The carbonate content of samples was determined using
the Chittick device described by Dreimanis (1962). Total sulfur in drill samples was
determined using a LECO SC432 furnace based on release of SO2 during combustion of
samples. Total sulfate was extracted with 10% Na2CO3. Sulfate was split into a gypsum
fraction, determined by leaching of 50 g of drilling powder in 200 ml of distilled water,
and a jarosite fraction, determined as weight difference after conversion of jarosite to
goethite by the application of NaOH (Choquette in Gelinas et al., 1994).
3.3. Water analysis
Piezometers were sampled with a WATERRA (foot valve) pump. Suction lysimeters
were sampled by the combination of pressure and suction pumping. Parameters such as
pH, temperature, and Eh were measured immediately after recovery of samples in the
field. The pH electrode (Orion Ross combination pH electrode, model 815600) was
calibrated with standard buffers, and the Eh electrode (Orion platinum redox electrode,
model 96-7800) was checked with a ZoBelles solution. Samples were then filtered
through a 0.45-Am membrane and split into two subsamples. One, designated for cation
analysis, was acidified with HNO3 to a pH of about 1.0. The second, designated for anion
analysis, was unacidified. All samples were analyzed for selected index parameters (Ca,
Mg, K, Fe2 +, Fetotal and SO4). Samples from Spring 1996 were also analyzed for Na, Cu,
Zn, Pb and some samples were also analyzed for Cl and PO4. The majority of the analyses
were conducted by atomic adsorption spectrometry (AAS). Sulfate, chloride and phosphate were determined by ion chromatography and Fe2 + by the potassium dichromate
method. Concentrations of Fe3 + were determined from the difference between Fetotal
and Fe2 +.
3.4. Isotopic analysis
Samples for D and 18O analysis were collected during both dry and wet periods. Several
samples had such high TDS content that they had to be diluted by toluene distillation prior
to the analysis. Results from the mass spectrometer were expressed as d18O and d D per
mil with respect to the Standard Mean Ocean Water (SMOW) standard, with analytical
precision F 0.15xand F 1x, respectively.
For 13C analysis, dissolved carbonate was precipitated as BaCO3 by the addition of
NaOH and BaCl2. Analysis of 13C was then conducted on CO2 evolved via reaction with
H3PO4 and results were reported in d13C per mil notation with respect to the PDB standard
with a precision of F 0.5x.
Dissolved sulfate was co-precipitated with BaCO3 as BaSO4. Then BaCO3 was
removed by acidification with 10% HCl. The oxygen in the sulfate samples was converted
to CO2 for 18O(SO4) analysis with the graphite reduction method. Analyses were reported
as d18O per mil with respect to the SMOW with a precision F 0.5x. Concentration of
34
S in the sulfate was analyzed using the SO2 gas produced by thermal decomposition of
51
BaSO4. Values were reported as 34S per mil with respect to the Canyon Diablo Troilite
(CDT) standard with a precision of F 0.3x.
3.5. Other measurements and modeling
Temperature and oxygen concentrations were also measured during dry and wet
periods. Concentrations of oxygen were determined with a temperature compensated
electrode of 0.1% resolution.
The water content in the unsaturated waste rock was determined by neutron activation
in boreholes about 12.0 m deep with PVC casings. The neutron probe was calibrated in a
barrel filled by waste rock and results were reported in g/cm3, corresponding to water
contents on a mass basis.
Flow and gas transport in the unsaturated zone were modeled using the code TOUGH
AMD adapted from the code TOUGH2 (Pruess, 1991), and described by Lefebvre (1994)
and Lefebvre et al. (2001). Hydrogeochemical modeling was performed using the code
SIMUL (Reardon, 1992). The code is based on Pitzers equations and can handle
extremely high ionic strength (at Mine Doyon in some cases >10 mol/l). The Pitzers
equation parameters were available for only 25 jC. Saturation indices were expressed in
logarithmic form (SI = log (IAP/Ksp)), e.g., values higher than zero indicate supersaturation, and values lower than zero indicate undersaturation with respect to a given mineral.
Table 1
Selected physical parameters (after Gelinas et al., 1994)
Parameter
Value/units
Bulk density
Inter-block porosity/intra-block porositya
Grain size d10
Grain size d 60
Van Genuchtens a/n
Saturated hydraulic conductivity
Hydraulic conductivity at 0.40 saturation
1836 kg/m3
0.33/0.05
0.5 1.0 mm
15 100 mm
0.23/0.504 Pa 1
10 3 m s 1
10 8 m s 1
Fresh material.
52
content at shallow depths was 0.078 for sericite schist and 0.038 for diorite during the dry
period. These values correspond to saturation values of 0.42 and 0.21, respectively.
Significant differences between the dry (August 1995) and wet period (March 1996)
existed only at shallow depth (less than 2.0 m) (Sracek, 1997).
4.2. Temperature and oxygen profiles
A temperature profile for Site 6 is shown in Fig. 3a. There was an increase in
temperature down to a depth of 6.0 m. At that depth, the temperature was as high as 60 jC
and increased slightly with depth. However, data between 5 and 15 m depth were not
available because those thermistors were damaged. Measurement of the phase and
amplitude of temperature variations were used in analytical solutions by Lefebvre et al.
(1993) to determine the thermal properties of waste rock. The temperature profile at Site
TBT (Fig. 3b) indicated a much lower maximum temperature of about 35 jC at 12-m
depth. This observation is consistent with less reactive diorite material at the top of that
Fig. 3. Temperature and oxygen profiles: (a) Site 6, (b) Site TBT, (c) Site 7.
53
site. The temperature profile at Site 7 (Fig. 3c) indicated an increase of temperature down
to about 32.0 m.
The oxygen concentration profile at Site 6 is shown in Fig. 3a. The concentration of
oxygen was high down to a depth of 10.0 m (about 15 vol.%) and then decreased to 2 3
vol.%. This behavior was interpreted to result from lateral convective transport of oxygen
from the slope of the pile at intermediate depths and diffusive transport at depth. The
decrease of oxygen concentration at Site TBT started deeper, at about 15.0 m (Fig. 3b) and
dropped to 2 3% at a depth of 25.0 m. High concentrations of oxygen at the top of the
profile appeared to be related to the less reactive diorite layer at the top. The profile at Site
7 (Fig. 3c) showed almost exponential decrease with depth, indicating a diffusive supply
of oxygen in the central zone of the pile as expected (Lefebvre et al., 1993; Ritchie, 1994).
Thus, both convective and diffusive regimes of the oxygen supply appear to be present
within the Mine Doyon pile. The presence of convective cells close to the slope and in the
upper zone of the pile was also revealed by the airborne survey using an infrared
thermographic camera (Gelinas et al., 1994). High-temperature anomalies were typical
especially for the upper zone close to the edges of the pile indicating that hot air was
leaving the pile. The horizontal distance separating temperature maxima and minima in the
central zone of pile varied from 10 to 15 m.
54
Fig. 4. Reduced and oxidized S profiles: (a) Site 6, (b) Site TBT, (c) Site 7.
observed in almost all samples. This mineral tends to crystallize close to the source of
potassium, epitaxially on muscovite (Sracek, 1997). Aggregates and clusters of gypsum
were observed on planes parallel to the schistosity of the sericite schist. The formation of
gypsum and jarosite observed under SEM seems to accelerate the oxidation of pyrite by
physically breaking-up the rock and thus increasing the accessibility of oxidants to fresh,
unoxidized pyrite grains within the waste rock fragments (Sracek, 1997).
Analysis of reduced sulfur concentrations in the solid phase, corresponding to the pyrite
content, showed an S-shaped curve close to the slope of the pile at Site 6 (Fig. 4a). The
deeper concentration minimum likely corresponded to the entry of oxygen supplied by
convection from the slope with a significant upward flow component. Trends at Site TBT
were less evident (Fig. 4b), but there was an initial increase of reduced sulfur concentration
followed by decrease with depth. A maximum of oxidized sulfur concentration was at a
depth of about 12.0 m (Sracek, 1997). The deeper oxidized sulfur maximum compared to
Site 6 was related to the less reactive diorite cover with lower concentrations of pyrite at
the top of the profile. Finally, there was an increase down to 5 m and then a gradual
decrease of reduced sulfur concentration at Site 7 (Fig. 4c). However, there was a decrease
of concentration below the depth at 15 m, which was interpreted as to be the result of a
paleo-surface (break of waste rock deposition) with high degree of pyrite oxidation at
shallow depths prior to ongoing deposition. The oxidized sulfur profile exhibited a
maximum at shallow depths (about 5.0 m) and then there was a general trend of decreasing
Table 2
Remaining pyrite and sulfate within the pile (1995)
Site
Pyrite
(kg)
Pyrite
(kg/tonne)
Sulfate
(kg)
Sulfate
(kg/tonne)
Pyrite/sulfate
(kg/kg)
Site 6
Site TBT
Site 7
3433
3326
4059
65.61
63.56
84.38
1124
1519
560
21.48
29.03
11.64
3.054
2.190
7.248
55
Table 3
Average gypsum and jarosite sulfate concentrations in the solid phase (1995)
Site
Gyp. SO4
(wt.%)
Gypsum
(wt.%)
Jar. SO4
(wt.%)
Jarosite
(wt.%)
Total SO4
(wt.%)
Calcite
(wt.%)
Site 6
Site TBT
0.63
2.29
1.13
4.10
2.20
2.35
5.70
6.03
2.84
4.64
0.59
1.04
6. Hydrogeochemical behavior
This section presents the results of sampling of suction lysimeters in the unsaturated
zone and piezometers in the saturated zone. Temporal and spatial trends of index
parameters (Ca, Mg, K, Fe3 +, Fetotal and SO4) with saturation indices for secondary
minerals are presented and discussed.
6.1. Temporal and spatial trends
There were two distinct periods of temporal trends based on the infiltration pattern: a
recharge period (late March early June) and a dry period (mid-June February). The
56
profiles of pH, Eh, Ca, Mg, Al, Fe3 +, Fetotal, and SO4 at Site 6 during both periods
(October 1995 and April 1996) are presented in Fig. 5a.
At Site 6, there was a slight increase of pH from values of about 2.0 at shallow depths
to values of about 3.0 in deeper zones in both periods. The concentrations of Mg and Al
reached their maximum values at a depth of 10.0 m in October 1995. The concentration of
Al was about 33,500 mg/l during the dry period, which appears to be the highest
concentration of Al reported for AMD. Concentration of Mg was also high, with a
maximum value of 24,000 mg/l during the dry period. The maximum concentrations
observed were much lower during the recharge period. There were only moderate
increases of concentrations with depth and maximum values were less than 10,000 mg/
l for both dissolved species discussed above.
The behavior of Fetotal was more complex. There was a minimum at shallow depths
(7.3 m), a local maximum at a depth of 10.0 m, and a steady increase from 22.0 m down
to water table. The peak disappeared during the recharge period, but the relative
minimum at 7.3 m was similar for both sampling periods. The behavior of sulfate was
similar, with a maximum value of 230,000 mg/l at 10.0 m depth during the dry period
and lower values (less than 100,000 mg/l) during the recharge period. Behavior of other
species is discussed later.
Concentrations for the same species at Site TBT are presented in Fig. 5b. Concentrations generally increased downward in both periods and reached maximum values at a
depth about 22.0 m. During the recharge period, concentrations were generally lower, but
the decreases were not as large as at Site 6. The profiles at Site 7 are not presented here
because only data from August 1995 were available. However, concentration maximums
at intermediate depths, followed by gradual decreases downward were observed at this site
(Sracek, 1997).
6.2. The Eh values and iron speciation
The Eh values probably reflect the variations in the dominant Fe2 +/Fe3 + redox couple
because concentrations of iron were generally higher than 20 g/l. Nordstrom et al. (1979)
have shown that Eh values are likely to be meaningful in high iron and low pH waters. The
values of Eh and Fe3 + concentrations at Site 6 are shown in Fig. 5a. Both parameters
decreased with some fluctuations below 10 m depth.
The principal reactions responsible for generation of dissolved iron are (Stumm and
Morgan, 1981):
Reaction (1) represents the oxidation of pyrite by atmospheric oxygen. Reaction (2)
represents the oxidation of Fe2 + to Fe3 + by oxygen and is considered to be the rate-
57
58
limiting step for the oxidation of pyrite (Singer and Stumm, 1970). Finally, reaction (3)
represents the oxidation of pyrite by ferric iron. The last reaction is dependent on reaction
(2) because it can take place only if the Fe2 + generated by the oxidation of pyrite is
recycled back to Fe3 +. Thus, when the concentration of O2 decreases significantly below
atmospheric values at depth greater than 10.0 m (Fig. 3), the Fe2 + is no longer oxidized
and remains in solution. This situation results in decreasing Eh values with depth.
Melanterite (FeSO47H2O) represents a potential solubility control on Fe2 +, but there
was undersaturation with respect to this phase for water samples below 10.0 m depth
(Sracek, 1997). Thus, ferrous iron likely behaved conservatively in the zones of the pile
with low oxygen concentrations.
The chemical behavior of iron is somewhat complicated by precipitation of Fe3 + minerals
including K-jarosite (KFe3(SO4)2(OH)6). Precipitation of K-jarosite is expressed as
K 3Fe3 2SO2
4 6H2 O KFe3 SO4 2 OH6 s 6H
and this reaction requires a source of K+. Concentrations of K+ in pore water were
generally less than 1 mg/l. The K+ is probably consumed by the precipitation of K-jarosite
in micro-layers on the surface of muscovite, and the concentrations of K+ in bulk solution
may not be representative of what is available for K-jarosite formation in the muscovite
interlayer spaces. Saturation indices for K-jarosite at Site 6 from April 1996 are shown in
Fig. 6a. There are no results available for 1995 because potassium was not included in
earlier analyses. The samples at a depth of 4.0 m and at 10.0 m were supersaturated with
respect to K-jarosite. Calculations are based on data from the recharge period, with lower
dissolved Fe3 + concentrations. It can be assumed that more samples were supersaturated
with respect to K-jarosite in the dry period. The maximum accumulation of jarosite based
on solid phase analyses was at a depth of 7.3 m, corresponding to a sharp decline of
Fetotal concentrations. Precipitation of other Fe3 + mineral phases such as Fe(OH)3 was
prevented by low pH conditions in most samples.
Fig. 6. (a) SI values for K-jarosite (April 1996), (b) dissolved Si (October 1995).
59
60
sulfate and precipitation of secondary sulfides was not expected because there is no
significant reductant available and 34S(SO4) values (Table 5) were almost constant.
Thus, the potential sinks for sulfate include the precipitation of K-jarosite in the shallow
zone of the pile with ferric iron and precipitation of gypsum as shown in the following
equation:
Ca2 SO2
4 2H2 O CaSO4 2H2 Os
The precipitation of K-jarosite requires Fe3 + and, thus, maximum concentrations of Kjarosite in the solid phase were found at relatively shallow depths (7.3 m at Site 6) where
Fe3 + is produced in the presence of oxygen. However, measurable quantities of K-jarosite
were also found at depth because of the extremely high sulfate concentrations that counterbalanced the decreasing concentrations of ferric iron.
The precipitation of gypsum is not directly dependent on redox or pH conditions, but
requires the input of Ca2 +. Thus, more gypsum was found at Site TBT that contained
higher residual calcite concentrations than at Site 6. All samples from the Site TBT were at
equilibrium with respect to gypsum. Samples from Site 6 were at equilibrium during the
dry period, but several samples were undersaturated with respect to gypsum during the
recharge period (Sracek, 1997). At Site 6, part of the gypsum formed in the earlier stage of
AMD generation has probably been dissolved as a consequence of low calcium
concentration in pore water and sulfate was flushed out of the pile.
6.5. Other dissolved species
The behavior of calcium was controlled by calcite dissolution and by equilibrium with
gypsum (Eq. (6)). Samples with extremely high sulfate concentrations in the summer of
1995 generally had lower concentrations of calcium (Fig. 5a) because extremely high
dissolved sulfate concentrations force Eq. (6) to the right.
The behavior of dissolved silica was strongly influenced by the ionic strength. There
was an inverse relation between these parameters in which maximum values of ionic
strength corresponded to the minimum concentrations of dissolved silica and vice versa
(Sracek, 1997). The concentration of Si vs. depth at Site 6 in October 1995 is shown in
Fig. 6b. Dissolved silica at the observed pH range is present as the uncharged species
H4SiO40 (Drever, 1997), and the activity coefficient for H4SiO40 increases with increasing
ionic strength. In this case, the reaction
SiO2am s 2H2 O H4 SiO04
is pushed to the left and amorphous silica precipitates as the ionic strength increases.
There was also a correlation observed between the concentration of Fe3 + and that of
several dissolved species including Na, Cu, Zn, and Pb (Sracek, 1997). No other saturation
values for minerals containing these species were observed. This suggests that coprecipitation of these metals with K- and Na-jarosite may have occurred. However, data
were limited (only from April 1996) and this remains a matter of conjecture.
61
7. Isotopic results
Results of stable isotope analyses presented in this section are discussed with the
purpose of relating it to the internal evaporation process within the pile, to elucidate the
behavior of sulfate, and to verify the possibility of neutralization of AMD by carbonates
present in the solid phase.
7.1. Deuterium and oxygen-18
The local meteoric water line (LMWL) was determined for the Mine Doyon region on
the basis of sampling of local precipitation. This equation of LMWL is
dD 7:02d18 O 7:67
The principal characteristic of precipitation at the Mine Doyon site was the large
difference between winter snow precipitation, (dD less than 120x, d18O less than
16x
) and summer rain precipitation (dD greater than 90x, d18O greater than
13x
). The difference was used to trace recharge pulses from the melting of snow.
The interpretation of processes within the pile is based on the departure from the
LMWL. When evaporation from a free water surface takes place, there is an enrichment in
heavier isotopes with a shift of values from the LMWL and the expected slope of the
resulting evaporation line is about 5.0 (Clark and Fritz, 1997). When evaporation takes
place within a porous media, the slope of the evaporation line changes (Allison, 1982;
Allison et al., 1983). The slope decreases to about 2.0 3.0 due to more resistance for
diffusion of water vapor in partially saturated porous media. This behavior was described
in arid regions by Dincer et al. (1974). Internal evaporation was observed at the Mine
Doyon site during the drilling operation in June 1994, when a borehole 22.0 m deep at Site
6 acted as a chimney for upward vapor transport, and the temperature of the vapor was 54
jC. The isotopic data for the summer 1995 samples are presented in Fig. 7a. There was
clear deviation from the LMWL, which can be expressed as
dD 2:4d18 O 66:0
The slope of 2.4 is consistent with findings of Allison (1982), and suggests internal
evaporation is occurring within the waste rock pile. The internal evaporation line intersects
. This is mid-point
the LMWL at a point with coordinates dD = 96x
, d18O = 13.6x
between typical composition of snow and early spring precipitation (May), suggesting an
almost equal contribution of melted snow and spring precipitation to the recharge in the
pile. There is a potential isotopic exchange with 18O in silicates, which would result in a
similar deviation from the LMWL. However, isotopic exchange of water with silicates is
generally limited at temperatures below 150 jC (Truesdell and Hulston, 1980; Clark and
Fritz, 1997).
The data from the recharge period (April 1996) are presented in Fig. 7b. There was
a shift towards snow isotopic values, indicating a significant recharge from melted
snow. At Site 6, only shallow samples (above 13.2 m depth) were influenced. On the
62
Fig. 7. Stable isotopes data: (a) Summer 1995, (b) Spring 1996.
other hand, a portion of snow recharge penetrated to the saturated zone at Site TBT
(Sracek, 1997). The contribution of snow recharge for different samples is shown in
Table 4. The mixing equation was applied, with an initial isotopic composition based
on the summer 1995 data and resulting isotopic compositions based on the early spring
1996 data.
The depth of snow recharge penetration seems to be dependent on the location in the
pile and on the type of rock, which also determines the oxidation rate, temperature, and,
thus, internal evaporation in the pile.
Table 4
Penetration of snow recharge based on stable isotope data (spring 1996)
Site
Site
Site
Site
Site
Site
Site
Site
6
6
6
6
TBT
TBT
TBT
Depth (m)
Comment
4.0
7.3
13.2
32.0
7.3
16.5
32.0
51.1
31.9
10.5
none
50.5
16.6
16.2
unsaturated zone
unsaturated zone
unsaturated zone
saturated zone
unsaturated zone
unsaturated zone
saturated zone
63
10
where d18Os, d18Ow, and d18Oa are 18O values in sulfate, water and air, respectively, and
ew and ea are fractionation factors for water and air, respectively. Fractionation factors are
site-specific and they were not available for the Mine Doyon waste rock. Simple
combinations of O2 from water and from air were assumed, resulting in a possible error
F 10% (Toran and Harris, 1989). The estimated contribution of O2 from water was from
85% to 95% (Table 5), which was consistent with the expected important role of Fe3 + in
the oxidation of pyrite. Any combination of fractionation factors presented by Taylor et al.
(1984) gave the contribution of water O2 close to 100%. Plotting of both d18Ow and
d18O(SO4) with depth revealed a difference between Site 6 and Site TBT (Fig. 8a,b). At
Site 6, there was only slight increase in d18O(SO4) values between 16.5 and 32.0 m. In
contrast, there was an enrichment of 18O in water in the same depth interval, caused by
evaporation. If the oxidation of pyrite by Fe3 + had occurred below 16.5 m depth, then the
resulting sulfate would implement O2 from water enriched in 18O, and this reaction would
have resulted in a shift of d18O(SO4) values. This did not occur, and pyrite oxidation in the
deep zone at Site 6 must have been limited. At Site TBT, both water and sulfate became
more enriched in 18O with depth. It therefore appears that some oxidation of pyrite
occurred in the deep zone at Site TBT.
Table 5
Sulfate isotopic data
Site/depth
Sulfate (mg/l)
34
18
18
S.6/1.67 m
S.6/16.5 m
S.6/32.0 m
S.TBT/7.3 m
S.TBT/22 m
Average
37,507
101,225
116,795
21,511
171,922
89,792
1.00
0.25
1.44
2.25
1.41
0.30
11.85
11.67
10.08
13.39
10.47
11.49
6.83
8.93
8.33
8.94
6.95
7.99
S (x)
Owater (x)
O(SO4) (x)
64
Fig. 8. d18O water and sulfate data: (a) Site 6, (b) Site TBT.
7.3. Carbon-13
The average d13C value of calcite in waste rock was 2.63x(Savoie et al., 1991).
Carbon generated by decomposition of organic matter has d13C values about 25x, and
the fractionation factor for dissolution of CO2 in water is almost negligible at pH less than
4.5 (Clark and Fritz, 1997), that was observed in the pile. Thus, the d13C(DIC)
approximates the carbon isotopic composition of a carbon source. The average d13C(DIC)
C(DIC) values in the saturated zone water were 21.42xand 8.12xat Site 6 and
Site TBT, respectively. These values correspond to 16.0% and 75% contributions of
carbon from calcite at Site 6, and Site TBT, respectively. These results are consistent with
the low content of residual calcite at Site 6 and with organic matter (wood and grass)
observed in the saturated zone at that site. At Site TBT, a significant input of carbon from
calcite dissolution masked the fingerprint of carbon from decomposition of organic matter.
No data on d13C were available for water from the unsaturated zone because CO2 was
expelled from water by combined effects of extreme ionic strength and temperature, and
also by suction applied in the suction lysimeters.
65
The quantity of water entering and discharging from the saturated zone was estimated
by base flow hydrograph separation for the trench surrounding the pile (Bourque, 1994).
The average recharge value for the pile based on hydrograph analyses was determined to
be 205 mm/year, which comprises about 24% of the average precipitation. The mass
balance based on simulation of saturated flow at the base of pile (Sracek, 1997) indicated
that less than 1.0% of water in the saturated zone infiltrates into bedrock underlying the
pile. Thus, discharge into the collection trench approximates well the recharge into the
saturated zone of the pile.
The quantity of water retained in fine grained material does not seem to change
significantly during the year except for depths shallower than 2.0 m (Sracek, 1997). The
retention of water within the pile was important only at the initial stage of the pile
construction, when fresh and relatively dry waste rock was deposited and infiltration was
initiated. Some time is required to wet up the pile to field capacity before water in the
unsaturated zone migrates to the saturated zone.
Retention of water in gypsum was determined by data on the composition of solids. The
average gypsum content in the waste rock was 1.13 wt.% at Site 6 and 4.10 wt.% at Site
TBT (Table 3). Water retained in gypsum was calculated using the bulk density of waste
rock (1836 kg/m3), and the thickness of the unsaturated zone (32.0 m). Assuming that
infiltration occurred over 13.5 years at an average rate of 205 mm/year, the estimated
quantity of water retained in gypsum is about 5.0% at Site 6, and 18.2% at Site TBT. This
means that a non-negligible quantity of water remains in the unsaturated zone locked in
secondary gypsum.
Internal evaporation has been confirmed by visual observation (vapor leaving boreholes
during drilling) and by isotopic data presented above. The AMD water was also sampled
for chloride, assuming that the only factor contributing to the increase of chloride
concentration was evaporation (Table 6). The concentration factors were expressed with
respect to the shallowest samples because the chloride input from precipitation was not
known. The concentration factors approached values from 6 to 7 in the deep unsaturated
zone, which indicates that up to 83 86% of deeper water was evaporated compared to the
shallowest suction lysimeter at a depth of 4.0 m. The evaporated water was convected
towards the upper zone of the pile. Comparison of data at a depth of 16.5 m indicated that
evaporation was two times larger at Site 6 than at Site TBT.
At the Mine Doyon site, the internal source of heat results in evaporation within the
porous media. It is assumed that there is a threshold value of infiltration necessary for
penetration of recharge to the water table. The water balance is complicated by reTable 6
Dissolved chloride data (April 1996)
Sample
Cl (mg/l)
Concentration factor
Site
Site
Site
Site
Site
Site
3
8
21
6
20
38
1.0
2.7
7.0
1.0
3.3
6.3
6: 4.0 m
6: 10.0 m
6: 16.5 m
TBT: 7.3 m
TBT: 16.5 m
TBT: 22.0 m
66
condensation of evaporated water close to the surface of the pile and by the existence of
preferential flow zones in large openings between blocks.
Hypotheses for the roles of infiltration, evaporation and re-condensation were tested
using the numerical multiphase flow code TOUGH AMD. The TOUGH AMD model was
adapted for acid mine drainage modeling and comprises the oxidation of pyrite, convective
and diffusive fluxes of oxygen, transport of heat, and advective transport of sulfate
(Lefebvre et al., 2001). However, geochemical reactions are not considered. Simulations
were run for a period of 13.5 year, corresponding to the lifetime of the pile in 1995. The
domain was wedge-shaped with the unsaturated zone 30 m thick and a base length of 85
m. The boundary conditions were: temperature 5 jC, water saturation 0.42, infiltration 350
mm/year and atmospheric oxygen fraction 0.2315. The water retention curve used for
modeling was derived by Lefebvre (1994) based on the grain size distribution of the
material from the pile. The right boundary corresponds to a symmetry line at the center of
the pile.
The calculated distribution of temperature is presented in Fig. 9a. The calculated
temperature maximum was more than 65 jC at 15 m from the upper left margin of the pile.
This is a consequence of the oxygen supply in the region. The region corresponds to the
zone of maximum evaporation and is represented by Site 6. The calculated temperature
was much lower at the right boundary of the modeling domain, corresponding to the
central zone of the pile (less than 25 jC). These results are consistent with simulations by
Pantelis and Ritchie (1993), Lefebvre (1994), and Lefebvre et al. (2001). Vapor flux (Fig.
9a) was high at distance of about 15 m from the slope and was directed upward. The vapor
Fig. 9. Numerical modeling: (a) Temperature and water vapor flux, (b) water saturation and water flux.
67
flux was limited in the central zone of the pile. The presence of an eddy in the central zone
was not confirmed in the field and remains questionable. In contrast, water flux (Fig. 9b)
was always downward and the maximum recharge of re-condensated water was estimated
to occur closer to the central zone of the pile, where convective vapor transport occurred to
the pile surface. This has a direct impact on the hydrogeochemical behavior because water
evaporated close to the slope does not return to its original location, but contributes to the
recharge closer to the central zone of the pile. The zones close to the slope also had lower
water contents (Fig. 9b). Thus, evaporation contributes to extremely high concentrations in
pore water observed at Site 6 near the edge of the pile. Concentrations of dissolved species
are lower at the much colder Site TBT that is closer to the central zone of the pile. This
suggests that both physical and geochemical processes in the pile are interconnected and
contribute to water quality within the pile.
68
69
the pile, and zones of lower temperature and diffusion-limited oxygen transport in the
central zone of the pile. Evaporated water does not return to the zone of evaporation close
to slope, but re-condensates and infiltrates closer to the central zone of the pile and,
therefore, contributes to the extreme concentrations of dissolved species observed in the
pore water in the unsaturated zone close to the slope during period without recharge.
These results indicate that both physical and geochemical processes within a waste rock
pile are interconnected for highly reactive sulphide waste rock, and they cannot be
considered separately. Furthermore, there is an important role of rock texture and strength
in the generation of acid mine drainage, where AMD generation rates are much faster in
more friable material even when the pyrite content of rocks is similar.
Acknowledgements
The authors acknowledge the assistance of Pierre Therrien from the Universite Laval
with application of the code TOUGH AMD. Thanks also go to Eric Reardon from the
University of Waterloo, who provided us with his code SIMUL, to Michel Gigue`re from
the Universite Laval, who performed the chemical analysis, and to Robert Drimmie and
his staff from the Isotope Laboratory of the University of Waterloo, who performed the
isotopic analysis. Assistance of Dominique Marceau during field sampling is appreciated.
Fieldwork was financed by the Mine Doyon, which belonged to the Barrick/Cambior
group during the project period. The first author gratefully appreciates financial support
awarded by NSERC Canada and FCAR Quebec. We also thank Uli Mayer from the
University of British Columbia in Vancouver and John Molson and Michel Aubertin from
Ecole Polytechnique in Montreal for their review of the paper, which helped to improve
this manuscript.
References
Allison, G.B., 1982. The relationship between 18O and deuterium in water in sand columns undergoing evaporation. J. Hydrol. 55, 163 169.
Allison, G.B., Barnes, C.J., Hughes, M.W., 1983. The distribution of deuterium and 18O in dry soils: 2. Experimental. J. Hydrol. 64, 377 397.
Appelo, C.A.J., Postma, D., 1993. Geochemistry, Groundwater and Pollution. A.A. Balkema, Rotterdam. 536 pp.
Blowes, D.W., Reardon, J.E., Jambor, J.L., Cherry, J.A., 1991. The formation and potential importance of
cemented layers in inactive sulfide mine tailings. Geochim. Cosmochim. Acta 55, 965 978.
Bourque, E., 1994. Hydrologie dune halde de steriles miniers affectee par la drainage minier acide (In French:
Hydrology of a waste rock pile influenced by acid mine drainage), MSc thesis, Universite Laval.
Clark, I., Fritz, P., 1997. Environmental Isotopes in Hydrogeology. Lewis Publishers, Boca Raton. 328 pp.
Dincer, T., Al-Mugrin, A., Zimmermann, U., 1974. Study of the infiltration and recharge through the sand dunes
in arid zones with special reference to the stable isotopes and thermonuclear tritium. J. Hydrol. 23, 79 100.
Dreimanis, A., 1962. Quantitative gazometric determination of calcite and dolomite by using Chittick apparatus.
J. Sediment. Petrol. 32, 520 529.
Drever, J.I., 1997. The Geochemistry of Natural Waters: Surface and Groundwater Environments, 3rd ed.
Prentice-Hall, New Jersey. 436 pp.
Dubrovsky, J.M., Cherry, J.A., Reardon, J.E., Vivyurka, A.J., 1985. Geochemical evolution of inactive pyritic
tailings in the Eliot Lake uranium district: 1. The Groundwater zone. Can. Geotech. J. 22, 110 128.
70
Gelinas, P., Lefebvre, R., Choquette, M., 1992. Characterization of acid mine drainage production from a waste
rock dump at La Mine Doyon, Quebec. 2nd Int. Conf. on Env. Issues and Manag. of Waste in Energy and
Mineral Production, Calgary, Alberta, Canada, 1 4 Sept. A.A. Balkema, Rotterdam, pp. 747 756.
Gelinas, P., Lefebvre, R., Choquette, M., Isabel, D., Locat, J., Guay, R., 1994. Monitoring and modeling of acid
mine drainage from waste rock dumps: Mine Doyon case study, Report GREGI 1994-12, Final report
presented to MEND Prediction committee, DSS contract 23440-3-9231/01-SQ.
Harries, J.R., Ritchie, A.I.M., 1985. Pore gas composition in waste rock dump undergoing pyritic oxidation. Soil
Sci. 140, 143 152.
Kuo, E.Y., Ritchie A.I.M., 1999. The impact of convection on the overall oxidation rates in sulfidic waste rock
dumps. Proceedings of Conference: Sudbury 99-Mining and the Environment. Paper AD2, vol. 1, pp. 9 18.
Lefebvre, R., 1994. Characterization and numerical modeling of acid mine drainage in waste rock dump, PhD
thesis, Universite Laval. 375 pp.
Lefebvre, R., Gelinas, P., Isabel, D., 1993. Heat transfer during acid mine drainage production in a waste rock
dump, La Mine Doyon, Quebec, Report GREGI 93-03 submitted to CANMET. 46 pp.
Lefebvre, R., Hockley, D., Smolensky, J., Lamontagne, A., 2001. Multiphase transfer processes in a waste
rock piles producing acid mine drainage: 2. Applications of numerical simulation. J. Contam. Hydrol. 52,
165 186.
McKay, L.D., Gillham, R.W., Cherry, J.A., 1993. Field experiments in a fractured clay till: 2. Solute and colloid
transport. Water Resour. Res. 29, 3879 3890.
Morin, K.A., Cherry, J.A., Dave, N.K., Lim, T.P., Vivyurka, A.J., 1988. Migration of acidic groundwater seepage
from uranium-tailings impoundments: 1. Field study and conceptual hydrogeochemical model. J. Contam.
Hydrol. 2, 271 303.
Morin, K.A., Home, I.A., Riehm, D., 1994. High frequency geochemical monitoring of the seepage from minerock dumps, BHP minerals copper mine, British Columbia. Proceedings of Pittsburg Conference, U.S.
Bureau Mines Special Publications SP 06A-94, pp. 355 364.
Nordstrom, D.K., 1982. The effect of sulfate in aluminium concentrations in natural waters: some stability
relations in the system Al2O3 SO3 H2O at 298 jK. Geochim. Cosmochim. Acta 46, 681 692.
Nordstrom, D.K., Ball, J.W., 1986. The geochemical behavior of aluminium in acidified surface streams. Science
232, 54 56.
Nordstrom, D.K., Plummer, L.N., Wigley, T.M.L., Wolery, T.J., Ball, J.W., 1979. A comparison of computerized chemical models for equilibrium calculations in aqueous systems. In: Jenne, E.A. (Ed.), Chemical
Modeling in Aqueous Systems. Am. Chem. Soc. Symp. Ser., vol. 93. Am. Chem. Soc., Washington, DC,
pp. 857 892.
Pantelis, G., Ritchie, A.I.M., 1993. Optimizing oxidation rates in heaps of pyritic material. In: Tomm, A.B., Apel,
M.I., Brierley, C.L. (Eds.), Biohydrometallurgical Technologies. Minerals Metals & Materials Society, Warrendale, PA, USA, pp. 731 738.
Parker, B.L., Gillham, R.W., Cherry, J.A., 1994. Diffusive disappearance of dense, immiscible phase organic
liquids in fractured geologic media. Groundwater 32, 805 820.
Pruess, K., 1991. TOUGH2A General-Purpose Numerical Simulator for Multiphase Fluid and Heat Transfer.
Lawrence Berkeley Laboratory LBL-29400, Berkeley, CA, USA. 102 pp.
Reardon, E., 1992. SIMULGeochemical Code Based on Pitzers Equations. Internal Report. University of
Waterloo, Waterloo, Canada.
Ritchie, A.I.M., 1994. The waste-rock environment. In: Jambor, J.L., Blowes, D.W. (Eds.), Short Course Handbook on Environmental Geochemistry of Sulfide Mine-Wastes. Mineralogical Association of Canada, Ottawa,
Canada, pp. 133 161.
Savoie, A., Trudel, P., Sauve, P., Hoy, L., Kheang, L., 1991. Geologie de la Mine Doyon (region Cadillac)
(Geology of Mine Doyon in Cadillac region), in French Rapport ET 90-05. Ministe`re de lEnergie et des
Ressources du Quebec, Quebec City, Canada. 80 pp.
Shafer, W.M., Smith, S., Luckay, C., Smith, T., 1994. Monitoring gaseous and liquid flux in sulfide waste rock.
Proceedings of Pittsburg Conference. U.S. Bureau Mines Special Publications, SP 06A-94, pp. 410 418.
Singer, P.C., Stumm, W., 1970. Acid mine drainage: the rate limiting step. Science 167, 1121 1123.
Smith, L., Lopez, D.L., Beckie, R., Morin, K., Dawson, R., Price, W., 1995. Hydrogeology of waste rock dumps,
Report for Dep. of Natural Resources Canada, Ontario, Canada.
71
Sracek, O., 1997. Hydrogeochemical and isotopic investigation of acid drainage from waste rock at Mine Doyon,
Quebec, Canada, PhD thesis. Universite Laval, Quebec, Canada.
Stockwell, J., Beckie, R., Smith, L., 2001. Hydrogeology of an unsaturated waste rock pile, Key Lake,
Saskatchewan. Proc. IAH Conf., Calgary, 1582 1587.
Strebel, O., Bottcher, J., Fritz, P., 1990. Use of isotope fractionation of sulfate sulfur and sulfate oxygen to
assess bacterial desulfurication in a sandy aquifer. J. Hydrol. 121, 155 172.
Stumm, W., Morgan, J.J., 1981. Aquatic Chemistry, 2nd ed. Wiley, New York. 780 pp.
Taylor, B.E., Wheeler, M.C., 1994. Sulfur- and oxygen-isotope geochemistry of acid mine drainage in the
Western United States, field and experimental studies revisited. In: Alpers, C.N., Blowes, D.W. (Eds.),
Environmental Geochemistry of Sulfide Oxidation. Am. Chem. Soc. Symp. Series, vol. 550, pp. 481 514.
Taylor, B.E., Wheeler, M.C., Nordstrom, D.K., 1984. Stable isotope geochemistry of acid mine drainage:
experimental oxidation of pyrite. Geochim. Cosmochim. Acta 48, 2669 2678.
Toran, L., 1987. Sulphate contamination in groundwater from a carbonate-hosted mine. J. Contam. Hydrol. 2,
239 253.
Toran, L., Harris, R.F., 1989. Interpretation of sulfur and oxygen isotopes in biological and abiological sulfide
oxidation. Geochim. Cosmochim. Acta 53, 2342 2348.
Truesdell, A.H., Hulston, J.R., 1980. Isotopic evidence on environments of geothermal systems. In: Fritz, P.,
Fontes, J.C. (Eds.), Handbook of Environmental Isotope Geochemistry, A: Vol. 1. The Terrestrial Environment. Elsevier, Amsterdam, The Netherlands, pp. 179 219.