Académique Documents
Professionnel Documents
Culture Documents
Operation
The 23BA20 board has sixteen output relays. Two
groups of eight contacts have the same common return. This allows to split the output channels only to
two different process voltage sources.
Processing function
The I/O micro controller (EAP Ein- Ausgabe-Prozessor / Input- output processor) activates any output
forced by the VAP of CMU (CMU = communication
unit) by a command output request. The EAP controls the time duration of a pulse output by the loaded
pulse length time value.
Settings
There are no settings required and possible on the
23BA20 board.
Signalling
The board monitors and checks its functionality as
well as the dialog via the peripheral bus. Detected errors are indicated and/or transmitted by the board:
- by the red LED ST on the front plate
- by the red LED PST on the front plate
- by diagnostic messages
LED ST
The ST LED indicates board errors or peripheral
bus errors.
The ST-LED indicates:
- board runs initialization procedure
- board is doing a cold- or warm start
- board has detected a memory error (RAM or
EPROM)
- micro controller faulty
- no dialog via the peripheral bus for at least 2
minutes. The board is not polled by the PBP of
CMU.
LED PST
The LED indicates an error at command output:
- 24 V DC for the output relays failed during command output
- Time out PBP during active output. Any active
output is stopped (switched off).
LED CO
At least one output relay is switched on. The CO
LED is direct connected to the 24 V DC. CO is ON for
the time an output is active (pulse or persistent).
17
RTU560
ST
Micro
controller
W 01
output
relay: K01
K08
RAM
k01
A 01
k02
A 02
k03
A 03
k04
A 04
k05
A 05
k06
A 06
k07
A 07
k08
A 08
W 02
K09
EPROM
EAP
CO
K1
K16
A 09
k10
A 10
k11
A 11
k12
A 12
k13
A 13
k14
A 14
k15
A 15
k16
A 16
z32
b32
d32
z30
b30
d30
z28
b28
d22
d28
z26
b26
d26
z24
b24
d24
z22
PST
+ 24 V DC
k09
b22
k1
18
RTU560
23TP21
R0031
R0011
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
19
18
17
19
18
23ET23
Sub-connector
z32
b32
d32
z30
b30
d30
z28
b28
d28
z26
b26
d26
z24
b24
d24
A (Faston
Signal identification
Meaning
Identification
A 01
binary output 01
A 02
binary output 02
A 03
binary output 03
A 04
binary output 04
A 05
binary output 05
A 06
binary output 06
A 07
binary output 07
A 08
binary output 08
A 09
binary output 09
A 10
binary output 10
A 11
binary output 11
A 12
binary output 12
A 13
binary output 13
A 14
binary output 14
A 15
binary output 15
z22
A 16
binary output 16
6,3)
b22
d22
ReRe
mark
cable shield
W 01
W 02
The pin configuration of 23ET23 subrack corresponds to the direct pin configuration of the board connector
TP21
ET23
19
RTU560
23TP21
R 0031
23BA20
k 01
k 02
A 03
k 03
3
A 04
k 04
4
k 05
A 05
5
k 06
A 06
A 07
k 08
A 08
8
k 09
A 09
9
k 10
A 10
10
k 11
A 11
11
k 12
A 12
12
k 13
A 13
13
k 14
A 14
14
k15
A 15
15
k16
A 16
16
17
b22
d22
18
19
Process
A 02
k 07
Signalidentific.
A 01
W 01
W 02
+ UP
- UP
UP = process voltage ( 24 / 48 / 60 V DC)
Fig. 2: Binary output 1 pole same process voltage circuit on both halfs.
* Pin assignment 23TP21
Board
23TP21
R0031
23TP21
R0011
17
19
b22
18
17
d22
19
18
20
RTU560
23BA20
23TP21
R 0031
k 01
1
k 02
A 03
k 03
3
A 04
k 04
4
k 05
A 05
5
k 06
A 06
A 07
k 08
A 08
8
k 09
A 09
9
k 10
A 10
10
k 11
A 11
11
k 12
A 12
12
k 13
A 13
13
k 14
A 14
14
k15
A 15
15
k16
A 16
16
17
b22
d22
18
19
Process
A 02
k 07
Signalidentific.
A 01
W 01
W 02
+ UP
- UP + Pn
- PN
UP = process voltage ( 24 / 48 / 60 V DC) e.g. 23BA22 test circuit
Fig. 3: Binary output 1 pole. Different process voltage sources on k 01-k 08 and k 09-k 16
* Pin assignment 23TP21
Board
23TP21
R0031
23TP21
R0011
17
19
b22
18
17
d22
19
18
21
RTU560
23TP21
R 0031
23BA20
k 01
Signalidentific.
A 01
k 02
A 02
A 03
k 03
3
A 04
k 04
4
k 05
A 05
5
k 06
A 06
6
k 07
A 07
k 08
A 08
8
k 09
A 09
9
k 10
A 10
10
k 11
A 11
11
k 12
A 12
12
k 13
A 13
13
k 14
A 14
14
k15
A 15
15
k16
A 16
16
17
b22
d22
18
19
Process
W 01
W 02
(- PN) - UP
+ UP (+ Pn)
23TP21
R0031
23TP21
R0011
17
19
b22
18
17
d22
19
18
22
23
24
RTU560
03/2001
Subject to alteration