Académique Documents
Professionnel Documents
Culture Documents
In a 30 mm thick cylinder shell the longitudinal as well as circumferential joints are double welded butt
welds with full penetration. Which of the following is true with regards to the longitudinal
and circumferential joints?
a.
b.
c.
d.
The MAWP of an existing vertical vessel will be affected in which of the following circumstances?
a.
b.
c.
d.
The hydrostatic pressure caused by 10 ft. of liquid column (specific gravity equal to 1) will be?
a.
b.
c.
d.
1100 mm
1105 mm
1095 mm
1110 mm
In the thickness formula used to calculate internal pressure for a shell the term "E" refers to what?
a.
b.
c.
d.
If the vessel part MAWP changes for any of the vessel parts
If the design pressure is reduced ( other factor remaining the same)
If the vessel height is changed by adding or deleting a shell course
Both A and C
10 psi
43.3 psi
4.33 psi
None of the above
API 510
ASME Section 1
ASME Section VIII, Division 1
None of the above
The code rules for testing vessels in service are detailed in:
a.
b.
c.
d.
API 510
API 570
ASME Section VIII, Division 1
None of the above
Longitudinal joints
circumferential joints, shell to shell
Shell to hemispherical head joint
Both a A and C above
If all other conditions remain the same the design thickness of which dished head (Torispherical,
9
a.
b.
c.
d.
10
Any Thickness-offset within the allowable tolerance shall be provided a minimum taper of:
a.
b.
c.
d.
11
12
Torispherical
Hemispherical
Ellipsoidal
All will have the same thickness
3 to 1 minimum
4 to 1 minimum
3 to 1 minimum
1 to 2 minimum
ASME Section VIII, Divison 1 specifies different acceptance criteria for weld reinforcement, which of
the following statements are true?
a. Permitted reinforcement for longitudinal seams is higher than circumferential seams
b. permitted reinforcement for longitudinal seams is lower than circumferential seams
c. Permitted reinforcement for longitudinal seams is the same as circumferential seams
d. permitted reinforcement does not depend on the location of the seam
MAWP for a vertical vessel is measured at:
a. Top most part of the vessel
b. Bottom most part of the vessel
c. At the mid point between the top and the bottom of the vessel
d. None of the above
13
A pressure vessel is designed with 0.85 joint efficiency and full penetration welds. The RT
14
a.
b.
c.
d.
Nil
Spot
100%
The T-joints will need to be radiographed
A vessel with a 50" O.D. and a 1 1/4" thickness is to be provided with standard torispherical heads
15
The heads shall be formed with crown radius and a minimu knuckle radius as follows:
a.
b.
c.
d.
16
If there is a confliuct between ASME Section VIII and API 510 codes, for vessel in service which of
the following shall take precedence?
a.
b.
c.
d.
17
Two head to shell joints, one joining a seamless hemispherical head to shell was radiographed for
the full length and the other joint joining a seamless standard torispherical head to shell was
spot radiographed. The weld joint efficiency for each of these joints will be:
a.
b.
c.
d.
18
25 inches, 4 inches
50 inches, 3 inches
40 inches, 3 3/4 inches
25 inches, 2 inches
1, 0.85
1, 1
0.85, 1
0.85, 0.85
ASME Section VIII Division 1 recommends the use of U.T. in place of R.T. (for a fully radiographed
vessel) for:
a.
b.
c.
d.
19
a.
b.
c.
d.
20
a.
b.
c.
d.
RT3 means E = 1
RT2 means E = 0.85
RT1 and RT2 may mean E = 1
RT4 means spot radiography
QUESTIONS
1
ANSWER
B
REFERENCES
ASME VIII, UW-3 (a)
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
D
B
C
C
C
A
D
A
A
B
A
D
B
C
B
B
C
B
C