Académique Documents
Professionnel Documents
Culture Documents
Model QS-550
Free-Standing
Tubestand
Service Manual
i - iv G
1-1 thru 1-6 G
2-1 thru 2-26 G
3-1 thru 3-6 G
4-1 thru 4-10 G
5-1 thru 5-6 G
This product has been classified as Class I, Type B by Underwriters Laboratories, Inc.
Equipment not suitable for use in the presence of a flammable anesthetic mixture of
air with oxygen or with nitrous oxide.
EU Authorized Representative:
Medizintechnik Berlin GmbH
Altentreptower, Strasse 59
12683 Berlin - Germany
Phone: +49-302-82 4726
Fax: +49-302-82 6382
E-mail: Medizintechnik.Berlin.GmbH@t-online.de
CHAPTER 1 - SPECIFICATIONS
PHYSICAL SPECIFICATIONS ................................................................. 1-3
SYSTEM SPECIFICATIONS .............................................................. 1-3
HANDGRIP SPECIFICATIONS .......................................................... 1-3
PERFORMANCE SPECIFICATIONS .................................................... 1-3
ELECTRICAL SPECIFICATIONS .............................................................. 1-4
SYSTEM OPTIONS ................................................................................ 1-4
SYSTEM OPERATING ENVIRONMENT .................................................... 1-4
NON-OPERATING ENVIRONMENT ......................................................... 1-5
COMPATIBILITY STATEMENT ............................................................... 1-5
CHAPTER 5 - DIAGRAM
Model QS-550 Tubestand Sample Configuration Diagram ....................... 5-3
Model QS-550 Tubestand Wiring Diagram - Manual Collimator ................ 5-4
Model QS-550 Tubestand Wiring Diagram - Automatic Collimator
(Progeny Linear II) .............................................................................. 5-5
Model QS-550 Tubestand Wiring Diagram - Progeny Linear IV
Automatic Collimator ........................................................................... 5-6
SPECIFICATIONS
1-1
1-2
Chapter 1 Specifications
PHYSICAL SPECIFICATIONS
Refer to Figure 5-1 in Chapter 5, DIAGRAMS for Model QS-550 Tubestand dimensions.
SYSTEM SPECIFICATIONS
• Column Height: 92.0 inches (2336.8 mm)
• Tube Mount: Fork or Trunnion
• Weight: 600 lbs. (272.0 kg)
• Collimator
Compatibility: Manual, Selectable or Automatic, 10-20 lbs. (typi-
cal). Mounting to fork/tube housing requires four
1/4-20 or M6 x 16 bolts spaced on a 3.625" diame-
ter circle
• X-ray Tube
Compatibility: 3" or 4" rotating anode type, 30 - 40 lbs. (typical)
HANDGRIP SPECIFICATIONS
• Push Button
Switches: Vertical lock release, Longitudinal lock release,
Angulation lock release, Transverse lock release, All
Locks release, Auto-Stop
• LED Indicators: 40” (100 cm) SID, 72” (180 cm) SID
PERFORMANCE SPECIFICATIONS
• Tubestand
Longitudinal Travel: 96.0 inches (1752.6 mm)
• Vertical Travel (x-ray
tube): 60.0 inches (1524.0 mm)
• X-ray Tube Height: 72.5 inches (1848.2 mm) maximum to
13.75 inches (349.3 mm) minimum
• Transverse Tube
Travel: ±5 inches (127 mm) from centerline of table
• Transverse Travel
Detent: Center position
• X-ray Tube
Angulation: 240° (±120°)
• X-ray Tube Angulation
Detents: 0°, 90°(CW), 90°(CCW)
• Column Rotation: 180° (±90°)
• Column Rotation
Detents: 0°, 90°(L), 90°(R)
ELECTRICAL SPECIFICATIONS
Note: The following specifications are for the tubestand only and do not
apply to the x-ray tube or collimator. Refer to x-ray tube and collimator
manufacturer’s documentation (supplied with the tubestand) for
applicable specifications.
• Locking System
Power: +24 VDC, 1.0 Ampere
• Mode of Operation: Continuous
• Power Supply Type: Double (or Reinforced) Insulated (must meet con-
struction/performance criteria per UL 60601-1)
• Electrical
Interfacing: Tubestand-mounted terminal strip for interfacing
+24 VDC and, when equipped with automatic colli-
mator, tray sensing signals
SYSTEM OPTIONS
• Auto-Tracking System, with Motorized Vertical Motion (QS-MAT)
• Fork Mount (replaces Trunnion Mount)
• Automatic collimator interface (QS-ACT-550)
• Floor Grout Kit
• Model QS-550 tubestands equipped with TechVision Hand Grips option:
• TechVision replaces the standard equipment hand grips to provide tube
stand position controls and indicators and serves as a generator remote
control panel. Refer to the table below for the appropriate documentation for
the application:
OPERATOR SERVICE
APPLICATION TYPE
MANUAL MANUAL
Quantum(Non-integrated)
and DiRex(Integrated) DC30-048 DC30-049
ASSEMBLY &
INSTALLATION
2-1
2-2
Chapter 2 Assembly & Installation
OVERVIEW
This chapter describes the steps required to assemble and install the Model QS-550
tubestand, including making all required electrical connections, and performing all
required alignments and calibrations.
ROOM CONSTRUCTION
A conventional radiographic room construction should be used in the area where
the tubestand is to be installed. Consult with your State Health Department or
local Building Codes for specific radiation shielding requirements.
INSTALLATION PRECAUTIONS
Install the tubestand before installing the radiographic table.
Check that the space location, conduit arrangements and junction boxes are pre-
pared for the permanent installation of the tubestand. Verify that the location
and space allowed is sufficient for the full range of tubestand/Transverse Arm
travel without hitting any walls or structures in the room (see Figure 5-1 for
equipment dimensions). Note that the Transverse Arm in/out adjustment and the
Vertical Column position relative to the rear wall are critical. Column rotation in
the counterclockwise (right-hand) direction could result in the Tube Housing strik-
ing the wall before the 90 degree index position is reached.
CDRH CERTIFICATION
The tubestand is not a CDRH certifiable product. However, it must be compatible
and operate in conjunction with other components in the x-ray system so that the
x-ray system performs in compliance with CDRH performance standards.
REQUIRED TOOLS AND MATERIALS
The following tools and materials are required to complete the assembly and
installation procedures:
• Double-bubble level - two feet minimum length
• Tape Measure - eight feet minimum length
• Standard hand tools
• Alcohol - to clean the high-tension cable ends, tubehead, and high- tension
transformer sockets
• Dow-Corning DC4 vapor-proofing compound, silicon insulating grease or
equivalent - for packing x-ray tubehead and high-tension cable terminals
• Special film cassette (11" x 14" cassette with scribed centerline)
• Electric drill and drill bits
• Lubricant - white lithium grease
UNPACKING
Open crate or carton marked "packing list enclosed" first. Remove packing list
and use it as a guide to open the remaining cartons. Do not dispose of packing
material until packing list is matched with actual parts received. Should there be
a shortage or damage, notify Quantum Medical Imaging, LLC.’s customer service
department immediately. The manufacturer is relieved of any responsibility for
damage during shipment after unit is picked up by the carrier.
INSTALLATION INSTRUCTIONS
NOTE
When the tubestand is used with a vertical wall frame or wall stand, care should
Examine all
be taken during room planning and pre-installation to allow for the accurate align- cartons and
ment of these components. Alignment accuracy must be within 2% of the SID crates at time
used. After the tubestand Floor Track is aligned with the table receptor, the track of delivery. If
cannot be adjusted transversely. Therefore, transverse alignment of the x-ray damage is
field to the image receptor in the vertical wall frame or wall stand must be made apparent, have
delivery driver
by adjusting the position of the image receptor within the wall stand or relocation write a "Dam-
of the entire wall stand. aged Ship-
All mounting procedures must be approved before and checked after installation ment Note" on
copies of
by the hospital or facility engineering department and a registered, professional, freight bill, sign
structural engineer. It is recommended that a leakage current measurement be it, and file
taken following installation to verify system meets allowable levels. appropriate
carrier claim.
To assemble and install the tubestand, proceed as follows: Should you dis-
Floor Track Installation cover con-
cealed
The area of the floor on which the Floor Track is to be mounted must be damage,
level in all directions. Shims may be used, however, grouting is recom- immediately
mended. notify the
transporting
1. Position the Floor Track in the proper location for installation. agent and ask
for an "Inspec-
2. Using a bubble-level, check that the Floor Track is level both lon- tion of Dam-
gitudinally and transversely. If not, shims can be used to level age". Carrier
track, however, grout is recommended. will not accept
concealed
3. Fasten the Floor Track to the floor using appropriate fastening damage claim
hardware (capable of supporting 100 lb. pull-load) depending on if filed after 15
the installation site (see Figure 2-1). days from date
of receipt of
4. Install five (5) Hole Plugs in holes for floor mounting screws. merchandise
Vertical Column/Base Assembly Attachment
1. Remove the shipping bolt located in the end of the Vertical Col-
umn shaft.
2. Remove eight (8) screws securing the left and right side Base
Access Panels to the Base Assembly and remove panels.
3. Mount the Base Assembly to the Vertical Column and secure to
Vertical Column Shaft using the supplied retaining ring (see Fig-
ure 2-2).
MOUNTING
HOLES (5X)
RETAINING
RING
FRONT
BEARING
BRACKET
BEARING W/
ECCENTRIC
BUSHING (2X)
REAR
BEARING
BRACKET (2X)
1. Re-install the End Cap to the end of the Floor Track using four (4) 5/16-18 x
1/2" hex head bolts, lockwashers and flat washers.
2. Using a two-foot (minimum) double-bubble level, placed on the front of the
Vertical Column, check that the Vertical Column is plumb. If not, adjustment
can be made by rotating the two (2) Vertical Angle Adjustment Bearings with
eccentric bushings (see Figure 2-4). Loosen the two (2) eccentric bearings
mounted to the rear of the Base Assembly; rotate the bearings to adjust. Re-
tighten the bearings after the column angle adjustment is made.
INSTALLING THE X-RAY TUBE, COLLIMATOR AND HANDGRIPS
The system is supplied with either a Trunnion type x-ray tube mounting bracket or
a Tube Mounting Fork. Refer to the appropriate paragraph that follows corre-
sponding with the type of x-ray tube mounting bracket used on your system. On
systems equipped with optional TechVision Hand Grips, refer to TechVision Ser-
vice Manual for complete hand grips mounting instructions.
Trunnion Configuration
1. Install the Trunnion Assembly onto the Transverse Arm using four
(4) 1/4-20 x 2" hex head bolts and lockwashers (see Figures 2-5
and 2-6). There are two sets of four (4) Trunnion mounting holes
that can be used as shown in Figure 2-5. The upper set of holes
is used when mounting 3-inch x-ray tubes. The lower set of
holes is used for mounting 4-inch x-ray tubes.
2. Remove top half of Trunnion Rings.
3. Place x-ray tube onto lower half of Trunnion Rings and re-mount
upper half.
4. Install Trunnion Handle on Trunnion Assembly using two (2) 1/4-
20 x 1/2" button head socket screws (see Figure 2-7).
TUBE SUPPORT
BRACKET
TRUNNION
ASSEMBLY
TRUNNION
HANDLE
1/4-20 X 1/2"
BUTTON HEAD
TRUNNION SOCKET SCREW
CAM (2X)
HANDGRIP
ASSEMBLY
COLLIMATOR
MOUNTING RING
TUBE FORK
COLLIMATOR
LEVELING SET
SCREW (4X)
TRANSVERSE ARM
INNER COVER
TRANSVERSE ARM
OUTER COVER
Figure 2-14. Trim Weight Access Opening (Front Side of Vertical Column)
LONGITUDINAL
BRAKE
ASSEMBLY
COLUMN ROTATION
ADJUSTMENT
SCREW (2X)
HORIZONTAL
SID SWITCH
ASSEMBLY
The Horizontal SID Switch Assembly mounts inside the Base Assembly (on the left
side when facing front of column) as shown in Figure 2-16. Proceed as follows:
1. Loosely install Horizontal SID Switch Assembly on rear wall of Base Assembly
using two (2) 10-32 x 1/2" phillips pan head screws, flat washers and kep
nuts.
2. Using a Switch Actuator placed on the Floor Track as a reference (do not peel
off adhesive backing at this time), adjust the height of the switch so that
when it contacts the actuator, the switch activates (clicks).
3. When the switch height is correct, tighten the two (2) 10-32 x 1/2" phillips
pan head screws.
4. Remove terminal strip cover from back of tubestand.
5. Connect wires from Horizontal SID Switch Assembly and Longitudinal Brake
Assembly to terminal block TB1 as follows:
Table 2-1. Manual Collimator TB1 Wiring
WIRE CONNECTION
WIRE DESCRIPTION
COLOR ON TB1
LONGITUDINAL MAGNET RED TB1-6
WIRE CONNECTION
WIRE DESCRIPTION
COLOR ON TB1
LONGITUDINAL MAGNET RED TB1-6
VERTICAL SID
SWITCH VERTICAL
ASSEMBLY COLUMN
SID SWITCH
CABLE CLAMP CABLE
LOWER HALF
CABLE
CLAMP (2X) TERMINAL
STRIP COVER
3. Install a High Voltage Cable Strain Relief on each high voltage cable attach-
ment to x-ray tube horns. (see Figure 2-19).
HIGH VOLTAGE
CABLE
STRAIN RELIEFS
(2X)
4. Clean marked area with alcohol and secure actuator in marked location using
double-sided tape.
5. Check switch height to ensure activation at 40" SID.
VERTICAL DISTANCE SCALES
The Vertical Distance Scales mount on the front side of the Vertical Column (see
Figure 2-21). The Vertical Distance Scales, calibrated in either centimeters (met-
ric system) or inches (SAE system), indicate the focal spot-to-bucky and focal
NOTE
spot-to-tabletop distances
Bucky and table Bucky SID
SID measure-
1. Set tube position for 40" (100 cm) bucky SID.
ments and
markings are 2. Affix label on Vertical Column so that the 40" (100 cm) mark lines
made sepa- up with the arrow in the bucky SID window of the SID Indicator
rately and inde- Bracket.
pendently of
each other. Table SID
1. Set tube position for 40" (100 cm) tabletop SID.
2. Affix label on Vertical Column so that the 40" (100 cm) mark lines
up with the arrow in the table SID window of the SID Indicator
Bracket.
"BUCKY"
VERTICAL SID SID INDICATOR
INDICATOR BRACKET
"TABLE"
VERTICAL SID
INDICATOR
THEORY
OF OPERATION
3-1
3-2
Chapter 3 Theory of Operation
OVERVIEW
The Model QS-550 tubestand is a free-standing x-ray tube support device (i.e., does
not require wall and/or ceiling mounting) that provides a wide range of tube positions
through longitudinal, vertical, rotational, and transverse tubestand motions. The
Handgrip Assembly is designed for operator convenience with ergonomically posi-
tioned push button switches that enable tubestand movement when pressed.
The following paragraphs provide detailed theory of operation of the various tube-
stand functions. See Figure 5-2, 5-3, 5-4 in Chapter 5, DIAGRAMS for system sche-
matics.
THEORY OF OPERATION
VERTICAL MOTION OPERATION
The vertical motion of the x-ray tube is controlled by a fail-safe type "vertical
brake"; when power is removed from the system, the brake remains mechanically
locked. A +24 VDC input, typically provided from the radiographic system’s x-ray
generator, is applied through connector TB1-1 and switch S1-2 to Vertical Lock
Switch S2-1. When S2 is pressed, the +24 VDC is applied to electromagnetic Ver-
tical Lock Coil L1, releasing the brake (i.e., magnetic lock) and enabling vertical
positioning of the x-ray tube. When Vertical Lock Switch S2 is released, +24 VDC
is immediately removed from L1 and the vertical brake (magnetic lock) is acti-
vated inhibiting x-ray tube vertical motion.
LONGITUDINAL MOTION OPERATION
The longitudinal motion of the x-ray tube (i.e., entire Vertical Column) is con-
trolled by a "longitudinal brake" located in the tubestand’s Base Assembly. The
+24 VDC input is applied through connector TB1-1 and switch S1 to Longitudinal
Lock Switch S3-1. When S3 is pressed, the +24 VDC is removed from electro-
magnetic Longitudinal Lock Coil L3, releasing the brake (i.e., magnetic lock) and
enabling longitudinal positioning of the x-ray tube. When push button S3 is
released, +24 VDC is immediately applied to L3 and the longitudinal brake (mag-
netic lock) is activated inhibiting x-ray tube longitudinal motion.
ANGULATION MOTION OPERATION
The angulation motion of the x-ray tube (i.e., clockwise and counter-clockwise
rotation of the x-ray tube) is controlled by an "angulation brake" located in the
tubestand’s Transverse Arm Assembly. The +24 VDC input is applied through
connector TB1-1 and switch S1 to Angulation Lock Switch S4-1. When S4 is
pressed, the +24 VDC is removed from electromagnetic Angulation Lock Coil L2,
releasing the brake (i.e., magnetic lock) and enabling rotation of the x-ray tube.
When push button S4 is released, +24 VDC is immediately applied to L2 and the
angulation brake (magnetic lock) is activated inhibiting x-ray tube angulation
motion.
SERVICE
INSTRUCTIONS
4-1
4-2
Chapter 4 Service Instructions
OVERVIEW
This chapter is designed to assist the service technician in maintaining the smooth
operation of the tubestand. The tubestand will function reliably when maintained
according to the instructions provided in this chapter. Safe equipment performance
requires the attention of service personnel who are specifically trained and experi-
enced with medical x-ray apparatus. Applicable preventive maintenance or any repair
service should be performed by these skilled individuals. Failure to follow manufac-
turer’s or service personnel’s recommendations may result in serious injury.
SERVICE MAINTENANCE
Visual Inspection
The following inspection and adjustment procedures are recommended to
maintain the system in its original operating condition.
Perform Every Six Months:
• Check for evidence of loose hardware or loose wires
• Check all bearings and bearing surfaces for cleanliness and
corrosion
• Clean Bearing Tracks, Floor Track
• Conduct a general inspection for worn or damaged parts
• Check for proper counterbalancing and smoothness of
vertical (up/down) tubestand motion
• Verify that all ground conductors are properly and securely
installed and free of corrosion or damage
• Check all electrical cabling and wiring for wear and fraying
Perform Annually:
• Lubricate tube rotation detents, angulation plate, transverse
assembly bearing wheels, column rotation detents using
lithium grease
TROUBLESHOOTING PROCEDURE
The following table provides instructions for troubleshooting problems that could
be encountered on Model QS-550 tubestand.
40" SID or 72" SID • Loss of +24 VDC power. 1. Check for +24 VDC on hand-
indicators not function- grips cable connector A3P1-
• Horizontal Switch (40"
ing 24.
WALL SID or 72" WALL
2. Check Horizontal Switch (40"
SID) failure
WALL SID or 72" WALL SID).
• SID lamp failure 3. Replace SID lamp.
ORDERING INFORMATION
To order replacement parts for the tubestand, contact the Service Department at;
Quantum Medical Imaging, LLC.
2002-B Orville Drive North
Ronkonkoma, New York 11779-7661 USA
Phone: (631) 567-5800 (x2)
Fax: (631) 567-5074
e-mail: service@qmiteam.com
When ordering replacement parts, supply the following information:
• Model and serial number of equipment
• Part number
• Part description
• Quantity required
• P.O. Number
• Shipping Instructions
When ordering components or parts not listed in Table 4-2, a complete descrip-
tion of the part, including its function and location should be provided with the
model number and serial number of the unit. Use only original replacement
parts, as supplied or recommended by Quantum Medical Imaging, LLC
1
2
(ANGULATION
MAGNET)
2
(LONGITUDINAL
MAGNET)
5
NOTE: Vertical SID
switch and actuator
are shown in this
figure; the
Horizontal SID
switch, located in
the Base Assembly,
and longitudinal
actuators have the
same respective
part numbers.
6
7 10
8 11
9 12
14
13
DIAGRAMS
5-1
5-2
Chapter 5 Diagrams
61/2" [165]
1/2
18 " [470]
AUTO-TRACK
ENABLE SWITCH
72.75 MAX NOTE 10
92.00 [1848]
[2337] 40"
NOTE 8 [1016] C.G.
93.38 7.92 NOTE 7
NOTE 9
72.75 MAX.
[1848]
13.00 MIN.
32.5 [330] AUTO-TRACK
[825] ENABLE SWITCH
NOTE 10
13.00 MIN
[330]
ORANGE
D7 ANGLE LONGITUDINAL TRANSVERSE VERTICAL
BROWN
NO 1 GROUND STUD LOCK LOCK LOCK LOCK
2 COM
RED
1N4005 GENERATOR GROUND
NC 3 L2 L3 L4 L1
D6
40" WALL SID SW 1N4005 D2 D3 D4 D1
S8 NO 1
2 COM
RED
ORANGE
YELLOW
RED
TUBESTAND NC 3 1N4005 1N4005 1N4005 1N4005
RED
GREEN
ASSEMBLY 72" WALL SID SW
S9
BROWN
BLACK
BLACK
BLACK
24 VAC
FROM 24 VAC
GENERATOR GROUND
9
8
7
6
5
4
3
2
1
20
19
18
17
16
15
14
13
12
10
11
TB1
20
19
18
17
16
15
14
13
12
10
11
9
8
7
6
5
4
3
2
1
AY30-023
WHITE
COLLIMATOR BLACK
GREEN
GRY
ORN
WHT
GRN
RED
BRN
PUR
BLU
YEL
BLK
10
15
14
13
12
P1
11
5
10
15
14
13
12
11
5
J1
40 INCHES 72 INCHES
LED 1 (LEFT) LED 2 (RIGHT)
GREEN/YELLOW
BROWN
WHITE
ORANGE
YELLOW
GRAY
BLUE
BLACK
RED
PURPLE
RED
S6
AUTOSTOP SW GROUND
D5 STUD
HANDGRIP
RED
ASSEMBLY
NC
NC
1N4005 BLACK
(AY20-020)
NC
2
NO
2
S3 S4
2
S5 LONG SW ANGLE SW
S2 TRANS SW
1
VERT SW
COM
COM
1
1
COM
COM
+24V
+24V
ORN
S1
NC 1 COM
2
NO 3 SC50-002T REV. E
NC 4 COM
5
NO 6
S10
NC 1 40" TABLE SID SWITCH
2 COM
NO 3 RED +24 VDC
S7 BLACK +24 VDC RTN FROM
40" TABLE SID SW
NC 3 GENERATOR
2 COM BLACK
NO 1
BROWN
ORANGE
GREEN/YELLOW
BROWN
ORANGE
S8 D7 ANGLE LONGITUDINAL TRANSVERSE VERTICAL
NC 6 COM S9 GROUND STUD LOCK LOCK LOCK LOCK
RED
5 NC 6 COM 1N4005 GENERATOR GROUND
YELLOW NO 4 5 L2 L3 L4 L1
NO 4 D6
NC 3 COM 1N4005 D2 D3 D4 D1
2 NC 3
NO 1 2 COM
RED
ORANGE
GREEN
RED
PURPLE
TUBESTAND NO 1 1N4005 1N4005 1N4005 1N4005
RED
BLUE
ASSEMBLY
GRAY
40" WALL SID SW DPDT
WHITE
72" WALL SID SW DPDT
BROWN
BLACK
BLACK
BLACK
9
8
7
6
5
4
3
2
1
20 20
19 19
18 18
17 17
16 16
15 15
14 14
13 13
12 12
10 10
11 11
TB1
9
8
7
6
5
4
3
2
1
VERTICAL COM
Automatic LONG. COMMON AY30-023
Collimator 40" SID WALL
Interface 40" SID TABLE
Box 72" SID WALL
GRY
ORN
WHT
GRN
RED
BRN
PUR
BLU
BLK
YEL
10
15
14
13
12
P1
11
5
15
14
13
12
11
10
5
J1
40 INCHES 72 INCHES
LED 1 (LEFT) LED 2 (RIGHT)
GREEN/YELLOW
BROWN
WHITE
GRAY
ORANGE
YELLOW
BLUE
BLACK
RED
PURPLE
RED
GROUND
S6
STUD
D5
HANDGRIP
RED
ASSEMBLY
2 NC
BLACK
2 NC
BLACK
(AY20-020) 1N4005
NC
AUTOSTOP SW
NO
S3 S4
2
S5 LONG SW ANGLE SW
S2 TRANS SW
1
VERT SW
1
COM
COM
COM
1
COM
+24V
+24V
ORN
S1
NC 1 COM
2
NO 3
NC 4 COM
5
SC50-010T REV. E
NO 6
3
2 COM COM BLACK
POT
NO 1
GREEN/YELLOW
1K
ORANGE
BROWN
2 BROWN
S8 D7 ANGLE LONGITUDINAL TRANSVERSE VERTICAL
S9
NC 6 GROUND STUD LOCK LOCK LOCK LOCK
COM NC 6
RED
RED 5 1N4005 GENERATOR GROUND
1
YELLOW NO 4 5 COM L2 L3 L4 L1
NO 4 D6
NC 3 1N4005 D2 D3 D4 D1
P/N: EL20-022 COM
2 NC 3
NO 1 2 COM
RED
ORANGE
PURPLE
GREEN
RED
TUBESTAND NO 1 1N4005 1N4005 1N4005 1N4005
RED
BLUE
ASSEMBLY
GRAY
40" WALL SID SW DPDT
72" WALL SID SW DPDT
WHITE
BROWN
BLACK
BLACK
BLACK
QT-750 TABLE
PBL CIRCUIT
TB2
12
10
11
9
8
7
6
5
4
3
2
1
20
19
18
17
16
15
14
13
12
10
11
9
8
7
6
5
4
3
2
1
TB1
20
19
18
17
16
15
14
13
12
10
11
9
8
7
6
5
4
3
2
1
AY30-023
GRAY
ORN
WHT
GRN
PUR
RED
BRN
BLU
YEL
BLK
11
10
9
15
14
13
12
10
P1
11
5
TS5
8
15
14
13
12
10
11
5
7 1 J1
6 2 HANDGRIP 40 INCHES 72 INCHES
LED 1 (LEFT) LED 2 (RIGHT)
GREEN/YELLOW
5 3 ASSEMBLY
4 4
BROWN
AY20-020
WHITE
3 5 ORANGE
GRAY
YELLOW
BLUE
BLACK
2 6
PURPLE
RED
1 7
8
9 RED
BLACK
10
BLACK
S6 GROUND
11
D5 STUD
12
RED
13
NC
2 NC
14 AUTOSTOP SW
1N4005
2 NC
15
2
TS6
2 NO
16
S3 S4
5
4
1
17
S5 LONG SW ANGLE SW
18
S2 TRANS SW
19
COM 1
COM 1
VERT SW
20
COM 1
COLL RDY
21
COM 1
22
GND
+24V
+24V
ORN
GENERATOR S1
COM
NC 1
2
NO 3
SC50-043T REV. D
NC 4 COM
1
2
3
4
5
6
7
TB2 5
INTERFACE BOARD NO 6