Académique Documents
Professionnel Documents
Culture Documents
Model SWB
Series 300
Model SWB
Series 200
Model SWB
Series 100
Model SFB
Model
del SWD
Table of Contents
Model SFD
DANGER
Always disconnect, lock and tag power source
before installing or servicing. Failure to disconnect
power source can result in fire, shock or serious
injury.
CAUTION
When servicing the fan, motor may be hot enough
to cause pain or injury. Allow motor to cool before
servicing.
CAUTION
Precaution should be taken in explosive
atmospheres.
DANGER
Pour carter les risques dincendie, de choc
lectrique ou de blessure grave, veiller toujours
dbrancher, verrouiller et tiqueter la source de
courant avant linstallation ou lentretien.
ATTENTION
Lors de toute intervention sur la soufflante, le moteur
peut tre suffisamment chaud pour provoquer
une douleur voire une blessure. Laisser le moteur
refroidir avant toute maintenance.
ATTENTION
Faire preuve de prcaution dans les atmosphres
explosives.
Receiving
Upon receiving the product, check to ensure all
items are accounted for by referencing the delivery
receipt or packing list. Inspect each crate or carton
for shipping damage before accepting delivery. Alert
the carrier of any damage detected. The customer
will make a notation of damage (or shortage of items)
on the delivery receipt and all copies of the bill of
lading which is countersigned by the delivering carrier.
If damaged, immediately contact your Greenheck
Representative. Any physical damage to the unit after
acceptance is not the responsibility of Greenheck Fan
Corporation.
Unpacking
Verify that all required parts and the correct quantity
of each item have been received. If any items are
missing, report shortages to your local representative
to arrange for obtaining missing parts. Sometimes it
is not possible that all items for the unit be shipped
together due to availability of transportation and truck
space. Conrmation of shipment(s) must be limited to
only items on the bill of lading.
Storage
Fans are protected against damage during shipment.
If the unit cannot be installed and operated
immediately, precautions need to be taken to prevent
deterioration of the unit during storage. The user
assumes responsibility of the fan and accessories
while in storage. The manufacturer will not be
responsible for damage during storage. These
suggestions are provided solely as a convenience
to the user.
Installation
Inspect the unit for any damage and report it to
the shipper immediately. Also, check to see that all
accessory items are accounted for.
Move the fan to the desired location and fasten
securely through mounting holes provided in the base
angles. The unit must be set level (shimming may be
necessary). Flexible duct connections and vibration
isolators should be used where noise is a factor.
The motor voltage and ampere rating must be
checked for compatibility with the electrical supply
prior to nal electrical connection. Supply wiring to the
fan must be properly fused, and conform to local and
national electrical codes.
The discharge is factory set as specied by customer
order, however, it can be rotated to other discharge
positions in the eld if necessary. Removal of the
housing bolts allows the discharge to be rotated to
the clockwise positions below. For TAD, BD and BAD
discharge positions, a portion of the frame angle must
be removed.
Clockwise rotation shown. Counterclockwise
discharge positions are a mirror image of those
shown. Fan rotation is always specied from the drive
side of the housing.
Discharge Positions
Optional Companion
Flange
40 in.**
(1016 mm)
Weatherhood
3 Wheel
Diameters
18 in.*
(457 mm)
Duct
from
kitchen
hood
This drawing is for dimensional information only. See the latest edition
of NFPA 96 Standard for Ventilation Control and Fire Protection of
Commercial Cooking Operations for detailed installation instructions,
materials, duct connections and clearances.
CW BH
CW TH
CW BAU
CW TAD
CW UB
CW TAU
CW DB
CW BAD
Affect of Installation on
Performance
Pre-Starting Checks
DANGER
CAUTION
When servicing the fan, motor may be hot enough
to cause pain or injury. Allow motor to cool before
servicing.
CAUTION
Precaution should be taken in explosive
atmospheres.
o
DANGER
7 MAX.
POOR
GOOD
FAIR
ATTENTION
FAIR
POOR
POOR
ATTENTION
Faire preuve de prcaution dans les atmosphres
explosives.
One
Impeller
Dia.
Turning
Varies
Should be at least
1/2 Impeller Dia.
POOR
FAIR
GOOD
FAIR
GOOD
CORRECT
POOR
POOR
WRONG
WRONG
WRONG
Figure 1
FAIR
Wheels
Gap
Radial
Gap
Wheel
Wheel
Figure 2
Model SWB / SWD
Unit Size
SFD
6
7.5
9
10
SFB
9
10
12
15
18
20
22
SWD
7
8
10
13
15
16
18
106
107
108
110
113
115
116
118
120
124
Overlap
8 (10)
3 (10)
8
7
16 (11)
1 (13)
2
1 (13)
2
5 (16)
8
5 (16)
8
11
16 (18)
3 (19)
4
7 (22)
8
15
16 (24)
1116 (27)
1316 (30)
114 (32)
1716 (37)
1916 (40)
3
327
330
333
336
340
344
349
Figure 3
Model SFD / SFB
SFD
SFB
Gap
Gap
8 (10)
8 (10)
1 (13)
2
1 (13)
2
Radial
Gap
inches (mm)
206
207
208
210
212
213
215
216
218
220
222
224
25
27
30
Overlap
Tolerance
1 (6)
4
1 (6)
4
1 (6)
4
1 (6)
4
1 (6)
4
3 (10)
8
3 (10)
8
3 (10)
8
3 (10)
8
1 (6)
4
3 (10)
8
3 (10)
8
3 (10)
8
3 (10)
8
3 (10)
8
1 (13)
2
32 (4)
5
32 (4)
5
32 (4)
5
32 (4)
5
32 (4)
5
32 (4)
5
32 (4)
5
32 (4)
5
32 (4)
3
16 (5)
3
16 (5)
3
16 (5)
3
16 (5)
1 (6)
4
5
16 (8)
5
16 (8)
5
3
3
2 (13)
2 (13)
1 (13)
2
1 (13)
2
1 (13)
2
1 (13)
2
5 (16)
8
5 (16)
8
3 (19)
4
3 (19)
4
3 (19)
4
1
1
Wheel Rotation
Rotation direction of the wheel is critical and incorrect
rotation will result in reduced air performance,
increased motor loading and possible motor burnout.
Check wheel rotation by momentarily energizing the
unit and noting if rotation is in the same direction as
the airow at the outlet and conforms to the rotation
decal afxed to the unit.
NOTE
Models SFD and SFB units should be operated only
when attached to the system for which they were
designed. Without proper system static pressure,
the motor could be overloaded.
Rotation
Rotation
Rotation
Airow
Airow
Airow
Backward Inclined
Forward Curved
Airfoil
Isolator Anchoring
Roof Truss
1/8 inch (3 mm) Thick
or 12 Gauge Min.
2000 Min. PSI
Concrete
Concrete
Deck Anchoring
Min. 5 inch
(127 mm)
Steel
Deck Anchoring
Wood Timber
Min. 4 inch (102 mm)
Min. G = 0.42
Timber Anchoring
Maintenance
Fan
RPM
To 250
500
750
1000
1250
1500
2000
2500
3000
3500
4000
5000
Number
of Shots
Standard Grease
Bearing Bore (inches)
1/2 -1
12
12
12
12
12
12
12
12
12
12
12
12
118 - 112
12
12
9
7
6
5
3
2
2
1
0.5
0.25
10
2716 - 3
12
8
6
4
3
2
1
0.5
0.25
16
Figure 4
Parts List
Each fan bears a manufacturers nameplate with model number and serial number embossed. This information
will assist the local Greenheck representative and the factory in providing service and replacement parts. Before
taking any corrective action, make certain unit is not capable of operation during repairs.
CAUTION
CAUTION
Scroll housing
Drive frame - base angle
Intake support panel
Inlet ring and cone
Wheel (specify rotation)
Drive frame assembly
Pillow block bearings
Fan shaft
Shaft pulley
Belt
Motor pulley
Belt tensioning bolts
Motor plate
Motor
Direct Drive
1
14
Belt Drive
1
7
8
9
5
6
10
14
11
2
13
10
12
Troubleshooting
WARNING
AVERTISSEMENT
PROBLEM
Excessive
Noise
Low CFM
High CFM
Static
Pressure
Wrong
CAUSE
CORRECTIVE ACTION
Adjust wheel and/or inlet cone. Tighten wheel hub or bearing collars on
shaft.
V-Belt Drive
Bearings
Wheel Unbalance
Clean all dirt off wheel. Check wheel balance, rebalance in place if
necessary.
Fan
Duct System
See page 3.
Fan
Duct System
Fan
High
Horsepower Duct System
Electrical Supply
Fan Doesnt
Operate
Drive
Overheated
Bearing
Motor
Lubrication
Mechanical
*Always check motor amps and compare to nameplate rating. Excessive fan speed may overload the motor
and result in burnout.
11
Our Commitment
As a result of our commitment to continuous improvement, Greenheck reserves the right to change specications
without notice.
Specic Greenheck product warranties are located on greenheck.com within the product area tabs and in the
Library under Warranties.
Greenhecks Centrifugal Utility Fans catalog provides
additional information describing the equipment, fan
performance, available accessories, and specication data.
Phone: 715.359.6171 Fax: 715.355.2399 Parts: 800.355.5354 E-mail: gfcinfo@greenheck.com Website: www.greenheck.com
12