Académique Documents
Professionnel Documents
Culture Documents
01
Date
2013-04-28
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or representations
of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website:
http://www.huawei.com
Email:
support@huawei.com
Issue 01 (2013-04-28)
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Contents
Contents
1 About This Document..................................................................................................................1
1.1 Scope..............................................................................................................................................................................1
1.2 Intended Audience..........................................................................................................................................................1
1.3 Change History...............................................................................................................................................................1
2 Overview.........................................................................................................................................2
2.1 Introduction....................................................................................................................................................................2
2.2 Benefits...........................................................................................................................................................................2
2.3 Architecture....................................................................................................................................................................2
3 Technical Description...................................................................................................................3
4 Related Features.............................................................................................................................6
5 Network Impact.............................................................................................................................7
6 Engineering Guidelines...............................................................................................................9
6.1 When to Use...................................................................................................................................................................9
6.2 Required Information.....................................................................................................................................................9
6.3 Deployment..................................................................................................................................................................10
6.3.1 Requirements.............................................................................................................................................................10
6.3.2 Data Preparation........................................................................................................................................................10
6.3.3 Activation..................................................................................................................................................................12
6.3.3.1 Using MML Commands.........................................................................................................................................12
6.3.3.2 MML Command Examples....................................................................................................................................13
6.3.3.3 Using the CME.......................................................................................................................................................13
6.3.4 Activation Observation..............................................................................................................................................14
6.3.5 Deactivation...............................................................................................................................................................14
6.3.5.1 Using MML Commands.........................................................................................................................................15
6.3.5.2 MML Command Examples....................................................................................................................................15
6.3.5.3 Using the CME.......................................................................................................................................................15
6.4 Performance Monitoring...............................................................................................................................................16
6.5 Parameter Optimization................................................................................................................................................19
6.6 Troubleshooting............................................................................................................................................................19
7 Parameters.....................................................................................................................................20
Issue 01 (2013-04-28)
ii
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Contents
8 Counters........................................................................................................................................86
9 Glossary.........................................................................................................................................87
10 Reference Documents...............................................................................................................88
Issue 01 (2013-04-28)
iii
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
1.1 Scope
This document describes WRFD-150236 Load Based Dynamic Adjustment of PCPICH,
including its technical principles, related features, network impact, and engineering guidelines.
Feature change
Changes in features of a specific product version
Editorial change
Changes in wording or addition of information that was not described in the earlier version
01 (2013-04-28)
This document is created for RAN15.0.
The content of the document is taken from Load Control Feature Parameter Description.
Issue 01 (2013-04-28)
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
2 Overview
Overview
2.1 Introduction
This feature decreases the P-CPICH transmit power for cells with high downlink non-HSPA
power consumption, therefore saving downlink non-HSPA power and increasing downlink cell
capacity.
2.2 Benefits
This feature reduces downlink non-HSPA power consumption by 10% to 15% for cells that
serve a large number of UEs and that have high downlink non-HSPA power consumption. The
reduction in power consumption means an additional 10% to 15% UEs can camp on the cells.
2.3 Architecture
This feature periodically checks the downlink non-HSPA power consumption of a cell. When
the power consumption reaches the preset upper limit, this feature reduces the P-CPICH transmit
power incrementally until the consumption falls into the normal range. When the power
consumption reaches the preset lower limit, this feature increases the P-CPICH transmit power
incrementally until the power consumption reaches the normal range.
When reducing the P-CPICH transmit power for a cell, this feature does not adjust the maximum
DPCH transmit power for UEs that have ongoing services in the cell. This is to ensure that these
UEs' radio links are stable.
When increasing the P-CPICH transmit power for a cell, this feature does not adjust the minimum
DPCH transmit power for UEs that have ongoing services in the cell. This is to ensure that the
DPCH power consumption in the cell does not increase.
Reducing the P-CPICH transmit power causes the cell coverage to shrink and the call drop rate
of cell edge UEs to increase.
Issue 01 (2013-04-28)
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
3 Technical Description
Technical Description
This feature dynamically adjusts the P-CPICH transmit power based on downlink non-HSPA
load in a cell to reduce downlink non-HSPA load for this cell. After the power adjustment, the
maximum and minimum transmit powers of the DPCH carrying online UEs are also changed.
To minimize the impact of power adjustment on online UEs, this feature provides compensation
for the maximum and minimum DPCH transmit power during the power adjustment procedure.
When DLLOAD_BASED_PCPICH_PWR_ADJ_SWITCH under the NBMLdcAlgoSwitch
parameter is selected, the Load Based Dynamic Adjustment of PCPICH feature is activated. The
RNC periodically checks the downlink non-HSPA power load in the current cell and adjusts the
P-CPICH transmit power.
Figure 3-1 shows the flowchart of the Load Based Dynamic Adjustment of PCPICH algorithm.
Issue 01 (2013-04-28)
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
3 Technical Description
Figure 3-1 Flowchart of the Load Based Dynamic Adjustment of PCPICH algorithm
The RNC checks the downlink non-HSPA load in the current cell at an interval specified by the
IntraFreqLdbPeriodTimerLen parameter. Then the RNC adjusts the P-CPICH transmit power
for this cell.
l
If downlink non-HSPA load in the current cell is equal to or larger than the value specified
in the PcpichPwrDownDlLoadState parameter, this cell is heavily loaded. In this situation,
the P-CPICH transmit power is reduced by the step PCPICHPowerPace so that cell-edge
UEs can be handed over to neighboring cells with lighter load. This reduces downlink power
load and increases downlink capacity of the current cell.
The minimum transmit power of the P-CPICH MinPCPICHPower is the lower limit for
power adjustment. That is, the P-CPICH transmit power will not be reduced after reaching
this limit. The maximum power reduction is the difference between the PCPICHPower
and MinPCPICHPower parameters. The PCPICHPower parameter specifies the PCPICH transmit power.
If downlink non-HSPA load in the current cell is smaller than the value specified in the
PcpichPwrUpDlLoadState parameter, this cell is lightly loaded. In this situation, additional
services can be processed in this cell and the P-CPICH transmit power can be increased by
the setp PCPICHPowerPace parameter. This extends the cell coverage to accommodate
cell-edge UEs from neighboring cells, therefore reducing the load of the neighboring cells.
The maximum transmit power of the P-CPICH MaxPCPICHPower is the upper limit for
power adjustment. That is, the P-CPICH transmit power will not be increased after reaching
this limit. The maximum power increase is the difference between the
MaxPCPICHPower and PCPICHPower parameters. The PCPICHPower parameter
specifies the P-CPICH transmit power.
Issue 01 (2013-04-28)
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
3 Technical Description
To minimize the impact of power adjustment on online UEs, this feature provides compensation
for the maximum and minimum DPCH transmit power during the power adjustment procedure.
l
If the adjusted P-CPICH transmit power is lower than the value of the PCPICHPower
parameter, the maximum transmit power of the DPCH carrying online UEs remains the
same as the power before the power adjustment to ensure link stability for online UEs.
If the adjusted P-CPICH transmit power is higher than the value of the PCPICHPower
parameter, the minimum transmit power of the DPCH carrying online UEs remains the
same as the power before the power adjustment to reduce non-HSPA power consumption.
NOTE
The minimum and maximum transmit powers for DPCH before the power adjustment are respectively the
sum of the PCPICHPower and RlMinDlPwr parameters, and the sum of the PCPICHPower and
RlMaxDlPwr parameters. For details about the RlMinDlPwr and RlMaxDlPwr parameters, see Power
Control Feature Parameter Description.
For details about downlink non-HSPA load, see Load Measurement Feature Parameter Description.
Issue 01 (2013-04-28)
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
4 Related Features
Related Features
Prerequisite Features
None.
Impacted Features
After this feature is activated, the TCP-based intra-frequency load balancing and uplink intrafrequency load balancing functions cease to take effect. For details of TCP-based intra-frequency
load balancing and uplink intra-frequency load balancing functions, see Load Control Feature
Parameter Description.
Issue 01 (2013-04-28)
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
5 Network Impact
Network Impact
System Capacity
This feature reduces the P-CPICH transmit power when downlink non-HSPA load in a cell is
heavy. This reduces power consumption of common channels and cell coverage. In this situation,
cell-edge UEs are handed over to neighboring cells, which reduces downlink non-HSPA load.
When HSDPA services are suppressed or rejected because of insufficient power, this feature
increases downlink capacity of the current cell.
NOTE
After pilot is adjusted, some HSDPA terminals cannot converge to the target BLER so as to affect power
efficient and cell throughput. It's recommended to turn CQI Adjustment Based on Dynamic BLER Target.
For details of CQI Adjustment Based on Dynamic BLER Target, see HSDPA Feature Parameter
Description.
For example, the value for PCPICHPower is 10% of the value for MaxTxPower and the
maximum P-CPICH power reduction is 3 dB. If downlink non-HSPA load in a cell is extremely
high and the number of UEs in this cell is large, this feature saves 10% to 15% of downlink nonHSPA cell power. The saved power can admit 10% to 15% extra UEs or increase at least 5% of
the average cell throughput.
The P-CPICH transmit power can be higher than the value for PCPICHPower. In this case, cell
coverage will increase but the available HSDPA power will decrease. This reduces average
HSDPA throughput if there are data transmission requirements.
Network Performance
This feature reduces the P-CPICH transmit power when downlink non-HSPA load in a cell is
heavy. As result, downlink non-HSPA cell load is reduced. When downlink power resources
are congested, this feature increases the access success rate during busy hours.
However, after the reduction of P-CPICH transmit power, cell coverage shrinks, leading to
coverage holes. Coverage holes cause the access success rate and the call drop rate for cell-edge
UEs to deteriorate. This increases the number of handovers. In multi-carrier scenarios, cells that
have the same coverage now may have different coverage. This affects the camping policy and
increases the blind-handover failure probability (Blind handovers here include blind-handoverbased DRD and LDR inter-frequency handovers). Ultimately, the performance of service
steering will be affected.
Issue 01 (2013-04-28)
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
5 Network Impact
The impact on network performance is determined by the actual cell coverage and the
distribution of cell-edge UEs.
l
If cell coverage is good and the number of cell-edge UEs is small, handovers and the call
drop rate will decrease.
If cell coverage is bad and the number of cell-edge UEs is large, handovers and the call
drop rate will increase.
After the power adjustment, if more cells that have the same coverage now have different
coverage, the probability of blind-handover failures will increase.
Issue 01 (2013-04-28)
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
6 Engineering Guidelines
Engineering Guidelines
One carrier serves a large number of UEs and there is a higher possibility of downlink nonHSPA power resource congestion.
To avoid the impact on call drop rate, you are recommended when one carrier of the GSM or
UMTS network provides continuous coverage for the current area in a multi-carrier scenario. In
a multi-carrier scenario, you are not advised to activate this feature for the carrier that provides
continuous coverage because this feature reduces coverage. You can, however, activate this
feature for other carriers in the multi-carrier scenario. It is recommended that carriers enabled
with this feature be configured with the coverage-based handover function so that UEs can be
handed over to carriers providing continuous coverage.
You are not advised to activate this feature if the P-CPICH transmit power configured for a cell
is low.
Continuous coverage
Before activating this feature, ensure that one or multiple carriers are providing continuous
coverage to the current area. This is to identify coverage holes, which may cause a higher
call drop rate and a lower handover success rate.
Network coverage
Obtain the coverage of the carriers that are to be enabled with this feature. If coverage holes
are likely to occur as a result of reduced cell coverage when the P-CPICH transmit power
is within the adjustment scope, you must estimate the impact of coverage holes on network
performance before you decide whether to activate this feature. (If the value of the KPI
Soft Handover Overhead is higher than 30%, cell coverage is good.)
Issue 01 (2013-04-28)
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
6 Engineering Guidelines
6.3 Deployment
6.3.1 Requirements
Verify that the license for the WRFD-150236 Load Based Dynamic Adjustment of PCPICH
feature has been activated before you deploy this feature.
Feature ID
Feature Name
License
Description
NE
Sales Unit
WRFD-150236
Load Based
Dynamic
Adjustment of
PCPICH
Load Based
Dynamic
Adjustment of
PCPICH (per
cell)
RNC
Per cell
This feature is introduced in RAN15.0 and requires the NodeB and RNC support RAN15.0.
Issue 01 (2013-04-28)
10
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
6 Engineering Guidelines
Parameter ID
Configuration Notes
Data Source
Switch for
Cell Load
Control
NBMLdcAlgoSwitc
h:
DLLOAD_BASED
_PCPICH_PWR_A
DJ_SWITCH
Engineering
Design
Function
Switch2
FuncSwitch2:
LOAD_BASED_P
CPICH_PWR_AD
J
None
Engineering
Design
Pcpich
Power
Down
Based On
DL Load
State
PcpichPwrDownDlLoadState
Default value/
Recommended
value
Pcpich
Power Up
Based On
DL Load
State
PcpichPwrUpDlLoadState
Default value/
Recommended
value
Intrafrequency
LDB
period
timer
length
IntraFreqLdbPeriodTimerLen
Radio network
plan (internal)
Radio network
plan (internal)
Max
Transmit
Power of
PCPICH
Radio network
plan (internal)
MaxPCPICHPower
Issue 01 (2013-04-28)
11
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
6 Engineering Guidelines
Parameter
Name
Parameter ID
Configuration Notes
Data Source
Min
Transmit
Power of
PCPICH
MinPCPICHPower
Radio network
plan (internal)
6.3.3 Activation
6.3.3.1 Using MML Commands
Step 1 Activate the cell-level license.
l Initial configuration: Run the RNC MML command ADD UCELLLICENSE. In this step,
select LOAD_BASED_PCPICH_PWR_ADJ under the Function Switch2 parameter.
l Reconfiguration: Run the RNC MML command MOD UCELLLICENSE. In this step,
select LOAD_BASED_PCPICH_PWR_ADJ under the Function Switch2 parameter.
Step 2 Run the RNC MML command SET ULDCPERIOD with Intra-frequency LDB period timer
length set to an appropriate value.
Step 3 Specify the pilot power adjustment step.
l Initial configuration: Run the RNC MML command ADD UCELLLDB with Pilot power
adjustment step set to an appropriate value.
l Reconfiguration: Run the RNC MML command MOD UCELLLDB with Pilot power
adjustment step set to an appropriate value.
Step 4 Specify the Pcpich Power Down Based On DL Load State and Pcpich Power Up Based On
DL Load State parameters.
l Initial configuration: Run the RNC MML command ADD UCELLLDM command. In this
step, set Pcpich Power Down Based On DL Load State and Pcpich Power Up Based On
DL Load State to appropriate values.
l Reconfiguration: Run the RNC MML command MOD UCELLLDM command. In this step,
set Pcpich Power Down Based On DL Load State and Pcpich Power Up Based On DL
Load State to appropriate values.
Step 5 Specify the maximum and minimum pilot transmit powers.
l Initial configuration: Run the RNC MML command ADD UPCPICH. In this step, set Max
Transmit Power of PCPICH and Min Transmit Power of PCPICH to appropriate values.
Issue 01 (2013-04-28)
12
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
6 Engineering Guidelines
l Reconfiguration: Run the RNC MML command MOD UPCPICHPWR. In this step, set
Max Transmit Power of PCPICH and Min Transmit Power of PCPICH to appropriate
values.
Step 6 Set the load-based dynamic adjustment of P-CPICH switch.
l Initial configuration: Run the RNC MML command ADD UCELLALGOSWITCH. In this
step, select DLLOAD_BASED_PCPICH_PWR_ADJ_SWITCH under the Switch for
Cell Load Control parameter.
l Reconfiguration: Run the RNC MML command MOD UCELLALGOSWITCH. In this
step, select DLLOAD_BASED_PCPICH_PWR_ADJ_SWITCH under the Switch for
Cell Load Control parameter.
----End
l When configuring the feature on the CME, perform a single configuration first, and then perform a
batch modification if required.
l Configure the parameters of a single object before a batch modification. Perform a batch modification
before logging out of the parameter setting interface.
Issue 01 (2013-04-28)
13
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
6 Engineering Guidelines
MO
NE
Parameter
Name
Parameter
ID
Configura
ble in CME
Batch
Modificati
on Center
UCELLLIC
ENSE
RNC
Function
Switch2
FuncSwitch
2
Yes
ULDCPERI
OD
RNC
Intrafrequency
LDB period
timer length
IntraFreqLd
bPeriodTim
erLen
Yes
UCELLLDB
RNC
Pilot power
adjustment
step
PCPICHPo
werPace
Yes
UCELLLD
M
RNC
Pcpich
Power Down
Based On
DL Load
State
PcpichPwrD
ownDlLoad
State
Yes
Pcpich
Power Up
Based On
DL Load
State
PcpichPwrU
pDlLoadStat
e
Max
Transmit
Power of
PCPICH
MaxPCPIC
HPower
Min
Transmit
Power of
PCPICH
MinPCPIC
HPower
Switch for
Cell Load
Control
NBMLdcAl
goSwitch
UPCPICH
UCELLAL
GOSWITC
H
RNC
RNC
Yes
Yes
6.3.5 Deactivation
Issue 01 (2013-04-28)
14
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
6 Engineering Guidelines
Run the RNC MML command SET ULDCPERIOD with Intra-frequency LDB period
timer length set to an appropriate value.
2.
Run the RNC MML command MOD UCELLLDB with Pilot power adjustment step set
to an appropriate value.
----End
l When configuring the feature on the CME, perform a single configuration first, and then perform a
batch modification if required.
l Configure the parameters of a single object before a batch modification. Perform a batch modification
before logging out of the parameter setting interface.
Issue 01 (2013-04-28)
15
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
6 Engineering Guidelines
MO
NE
Parameter
Name
Parameter ID
Configu
rable in
CME
Batch
Modific
ation
Center
UCELLAL
GOSWITC
H
RN
C
NBMLdcAlgoSw
itch
Yes
2 (Optional)
ULDCPER
IOD
RN
C
Intra-frequency
LDB period
timer length
IntraFreqLdbPe
riodTimerLen
Yes
UCELLLD
B
RN
C
Pilot power
adjustment step
PCPICHPowerP
ace
Yes
NOTE
If the TCP-based
intra-frequency load
balancing function
was enabled before
the feature
activation,
reconfigure the
Intra-frequency
LDB period timer
length and Pilot
power adjustment
step parameters
based on this
function after the
feature
deactivation.
Verify whether this feature takes effect by querying the values of the counters listed in
Table 6-4.
Issue 01 (2013-04-28)
Counter
Description
VS.CellBreath.CPICHUp
VS.CellBreath.CPICHDown
VS.CellBreath.CPICHMin.Time
16
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
6 Engineering Guidelines
Counter
Description
VS.CellBreath.CPICHMax.Time
Ensure that the TCP-based intra-frequency load balancing function is not enabled in the measurement
period. Otherwise, the value of the VS.CellBreath.CPICHUp or VS.CellBreath.CPICHDown counter may
be collected based on the TCP-based intra-frequency load balancing function.
Description
VS.MeanTCP.NonHS
Query the number of UEs in a cell and the cell HSDPA throughput.
If UEs attempt to access a cell whose downlink power resources are in the congested
state, this feature helps improve the access success rate and the number of online UEs
in this cell. See the counters listed in Table 6-6.
If no additional UEs attempt to access a cell with ongoing services, this feature helps
improve cell throughput. See the KPIs listed in Table 6-7. If only a small number of
UEs attempt to access this cell, downlink non-HSPA power in this cell will decrease.
See the value of the counter listed in Table 6-5.
Issue 01 (2013-04-28)
Counter
Description
VS.CellDCHUEs
VS.HSDPA.UE.Mean.Cell
17
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
6 Engineering Guidelines
KPI Type
Service Integrity
Service Integrity
Accessibility
Accessibility
Accessibility
While adjusting the P-CPICH transmit power, this feature increases the number of handovers
and affects the handover success rate. As a result, the call drop rate increases. See the values of
the counters listed in Table 6-8 and KPIs listed in Table 6-9. The value of these counters and
KPIs may increase after feature activation.
Table 6-8 Counters for call drop
Counter
Counter Type
Inter-frequency handovers:
Handover
VS.HHO.AttInterFreqOut.CS.TrigRscp
VS.HHO.AttInterFreqOut.CS.TrigEcNo
VS.HHO.AttInterFreqOut.PS.TrigRscp
VS.HHO.AttInterFreqOut.PS.TrigEcNo
Inter-RAT handovers:
Handover
VS.IRATHO.AttOutCS.TrigRscp
VS.IRATHO.AttOutCS.TrigEcNo
VS.IRATHO.AttOutPS.TrigRscp
VS.IRATHO.AttOutPS.TrigEcNo
Issue 01 (2013-04-28)
KPI
KPI Type
Retainability
Retainability
18
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
6 Engineering Guidelines
If the call drop rate increases noticeably after the feature activation, you can increase the
value of the PcpichPwrUpDlLoadState or PcpichPwrDownDlLoadState parameter to
increase the threshold for triggering reduction in the P-CPICH transmit power. For
example, you can change the value of the PcpichPwrDownDlLoadState parameter from
DlLoadedState to DlHeavyState.
6.6 Troubleshooting
None.
Issue 01 (2013-04-28)
19
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameters
NE
MML
Command
Feature ID
Feature Name
Description
NBMLdcAlgoS
witch
BSC6900
ADD
UCELLALGOS
WITCH
WRFD-151203
Camping
Strategy Switch
for Mass Event
Meaning:Wheth
er to enable the
algorithms
related to cell
load control.
Selecting a
switch enables
the
corresponding
algorithm and
clearing a switch
disables the
corresponding
algorithm. 1.
INTRA_FREQ
UENCY_LDB:
Whether to
enable the cell
breathing
algorithm. This
algorithm
adjusts PCPICH transmit
power of a cell
based on the
downlink TCP
load to achieve
load balancing
between intrafrequency cells.
This algorithm
MOD
UCELLALGOS
WITCH
WRFD-020106
WRFD-150231
WRFD-150219
WRFD-150216
WRFD-150217
WRFD-150215
WRFD-010610
03
WRFD-020102
WRFD-140223
WRFD-150236
WRFD-020101
WRFD-140226
WRFD-020107
WRFD-020104
WRFD-020105
WRFD-020126
WRFD-010612
02
WRFD-020129
WRFD-010626
WRFD-010627
WRFD-020103
Issue 01 (2013-04-28)
Load
Reshuffling
RIM Based
UMTS Target
Cell Selection
for LTE
Coverage Based
PS Redirection
from UMTS to
LTE
Load Based PS
Redirection
from UMTS to
LTE
Load Based PS
Handover from
UMTS to LTE
SRVCC from
LTE to UMTS
with PS
Handover
HSDPA
Admission
Control
Load
Measurement
20
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
WRFD-010660
MOCN Cell
Resource
Demarcation
automatically
becomes invalid
when the loadbased dynamic
P-CPICH
transmit power
adjustment
algorithm
(controlled by
the
DLLOAD_BAS
ED_PCPICH_P
WR_ADJ_SWI
TCH switch)
takes effect. 2.
PUC: Whether
to enable the
Potential User
Control (PUC)
algorithm. This
algorithm
adjusts cell
selection and
reselection
parameters
based on the cell
load to enable
UEs to reselect
lightly loaded
cells. 3.
UL_UU_OLC:
Whether to
enable the
uplink overload
control (OLC)
algorithm.
When the uplink
power is
overloaded in a
cell, this
algorithm
alleviates the
uplink load by
using quick
transport format
(TF) restriction,
distributing best
effort (BE)
WRFD-010661
WRFD-010662
WRFD-140102
Load Based
Dynamic
Adjustment of
PCPICH
WRFD-010660
04
Admission
Control
WRFD-010616
06
Fast Return
from UMTS to
LTE
WRFD-010663
WRFD-010665
WRFD-010660
02
WRFD-010660
03
WRFD-010660
01
WRFD-010616
05
WRFD-150220
WRFD-010616
01
WRFD-010616
03
WRFD-010616
02
WRFD-140217
WRFD-010616
04
WRFD-010616
WRFD-010616
08
WRFD-140218
Overload
Control
Intra Frequency
Load Balance
Potential User
Control
Mobility
Between UMTS
and LTE Phase 1
HSUPA
Admission
Control
PS Service
Redirection
from UMTS to
LTE
MBMS FLC
(Frequency
Layer
Convergence)/
FLD(Frequency
Layer
Dispersion)
FACH
Transmission
Sharing for
MBMS
Inter Frequency
Load Balance
MBMS Phase 2
MBMS over Iur
Issue 01 (2013-04-28)
21
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
Dynamic Power
Estimation for
MTCH
service to
common
channels, or
releasing UEs.
4.
DL_UU_OLC:
Whether to
enable the
downlink OLC
algorithm.
When the
downlink power
is overloaded in
a cell, this
algorithm
alleviates the
downlink load
by using quick
TF restriction,
distributing BE
services to
common
channels,
releasing UEs,
or reconfiguring
the maximum
transmit power
of FACHs. 5.
UL_UU_LDR:
Whether to
enable the
uplink load
reshuffling
(LDR)
algorithm.
When the uplink
load is heavy in
a cell, this
algorithm
alleviates the
uplink load by
using loadbased interfrequency
handovers, BE
service rate
reduction,
uncontrollable
MSCH
Scheduling
MBMS Channel
Audience
Rating Statistics
CS Fallback
Guarantee for
LTE Emergency
Calls
Inter-Frequency
Neighboring
Cell Selection
for MBMS PTP
Users
Streaming
Service on
MBMS
MBMS P2P
over HSDPA
MBMS
Admission
Enhancement
MBMS
Enhanced
Broadcast Mode
MBMS
Transport
Resource
Management
Coverage Based
PS Handover
from UMTS to
LTE
MBMS
Broadcast Mode
MBMS Load
Control
MBMS
Admission
Control
Issue 01 (2013-04-28)
22
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
Inter-Frequency
Load Balancing
Based on
Configurable
Load Threshold
real-time service
QoS
renegotiation,
load-based CS/
PS inter-RAT
handovers, and
AMR service
rate reduction. 6.
DL_UU_LDR:
Whether to
enable the
downlink LDR
algorithm.
When the
downlink load is
heavy in a cell,
this algorithm
alleviates the
downlink load
by using loadbased interfrequency
handovers, BE
service rate
reduction,
uncontrollable
real-time service
QoS
renegotiation,
load-based CS/
PS inter-RAT
handovers,
AMR service
rate reduction,
and MBMS
power
restriction. 7.
OLC_EVENT
MEAS:
Whether to
enable OLC
event
measurement. 8.
CELL_CODE_
LDR: Whether
to enable cell
code reshuffling
algorithm. In the
MBMS Soft/
Selective
Combining
MBMS
Introduction
Package
16/32/64/128Kb
ps Channel Rate
on MBMS
Service-Based
PS Handover
from UMTS to
LTE
Issue 01 (2013-04-28)
23
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
event of code
resource
overuse, this
algorithm
alleviates the
code resource
overuse by using
BE service rate
reduction, code
tree reshuffling,
and load-based
inter-frequency
handovers. 9.
CELL_CREDIT
_LDR: Whether
to enable the cell
credit
reshuffling
algorithm. In the
event of cell
credit overuse,
this algorithm
alleviates the
credit overuse
by using loadbased interfrequency
handovers, BE
service rate
reduction,
uncontrollable
real-time service
QoS
renegotiation,
and load-based
CS/PS interRAT handovers.
10.
UL_INTRA_FR
EQUENCY_UL
B: Whether to
enable RTWPbased intrafrequency load
balancing
algorithm. This
algorithm
adjusts P-
Issue 01 (2013-04-28)
24
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
CPICH transmit
power of a cell
based on the
RTWP load to
achieve load
balancing
between intrafrequency cells.
This algorithm
automatically
becomes invalid
when the loadbased dynamic
P-CPICH
transmit power
adjustment
algorithm
(controlled by
the
DLLOAD_BAS
ED_PCPICH_P
WR_ADJ_SWI
TCH switch)
takes effect. 11.
UL_UU_CLB:
Whether to
enable the
uplink loadbased CLB
algorithm. This
algorithm
determines
whether a cell
enters the CLB
state by the
uplink load on
the air interface.
If a cell is in the
CLB state,
measurementbased interfrequency
handovers are
triggered
periodically to
achieve load
balancing
between inter-
Issue 01 (2013-04-28)
25
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
frequency cells.
12.
DL_UU_CLB:
Whether to
enable the
downlink loadbased CLB
algorithm. This
algorithm
determines
whether a cell
enters the CLB
state by the
downlink load
on the air
interface. If a
cell is in the
CLB state,
measurementbased interfrequency
handovers are
triggered
periodically to
achieve load
balancing
between interfrequency cells.
13.
CELL_CODE_
CLB: Whether
to enable code
resource-based
CLB algorithm.
This algorithm
determines
whether a cell
enters the CLB
state by the code
resource usage.
If a cell is in the
CLB state,
measurementbased interfrequency
handovers are
triggered
periodically to
Issue 01 (2013-04-28)
26
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
achieve load
balancing
between interfrequency cells.
14.
CELL_CREDIT
_CLB: Whether
to enable creditbased CLB
algorithm. This
algorithm
determines
whether a cell
enters the CLB
state by the
credit resource
usage. If a cell is
in the CLB state,
measurementbased interfrequency
handovers are
triggered
periodically to
achieve load
balancing
between interfrequency cells.
15.
DLLOAD_BAS
ED_PCPICH_P
WR_ADJ_SWI
TCH: Whether
to enable
downlink loadbased dynamic
primary
common pilot
channel (PCPICH) power
adjustment
algorithm. This
algorithm
adjusts the PCPICH transmit
power by the
downlink nonHSPA power
Issue 01 (2013-04-28)
27
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
load to reduce
the downlink
non-HSPA
power load. If
this algorithm
takes effect,
other enabled
algorithms for
intra-frequency
load balancing
(based on TCP
or RTWP)
automatically
become invalid.
16.
ADAPTIVE_R
ACH: Function
switch for the
adaptive RACH
feature. When
this switch is
turned on, this
feature is
activated. In this
case, the RNC
adjusts the
random access
parameters
based on the
random access
state and on the
uplink power
load of the target
cell. When this
switch is turned
off, this feature
is deactivated.
17.
ACK_PRACH_
PREAM_MEA
S: Whether to
measure the
number of
acknowledged
PRACH
preambles.
When this
switch is turned
Issue 01 (2013-04-28)
28
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
on, the RNC
measures the
number of
acknowledged
PRACH
preambles.
When this
switch is turned
off, the RNC
does not
measure the
number of
acknowledged
PRACH
preambles. 18.
CAMPING_ST
RATEGY_SWI
TCH: Whether
to enable the
camping policy
switching
function when
traffic is heavy.
This is a
function switch
for the function.
When the switch
is turned on, the
camping policy
switching
function is
enabled if traffic
is heavy in the
entire network.
Then, the target
cell is no longer
a preferred
camping cell for
the UE in
question, but a
random
camping cell.
GUI Value
Range:INTRA_
FREQUENCY_
LDB, PUC,
UL_UU_LDR,
Issue 01 (2013-04-28)
29
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
DL_UU_LDR,
UL_UU_OLC,
DL_UU_OLC,
OLC_EVENT
MEAS,
CELL_CODE_
LDR,
CELL_CREDIT
_LDR,
UL_INTRA_FR
EQUENCY_UL
B,
UL_UU_CLB,
DL_UU_CLB,
CELL_CODE_
CLB,
CELL_CREDIT
_CLB,
DLLOAD_BAS
ED_PCPICH_P
WR_ADJ_SWI
TCH,
ADAPTIVE_R
ACH,
ACK_PRACH_
PREAM_MEA
S,
CAMPING_ST
RATEGY_SWI
TCH
Unit:None
Actual Value
Range:INTRA_
FREQUENCY_
LDB, PUC,
UL_UU_LDR,
DL_UU_LDR,
UL_UU_OLC,
DL_UU_OLC,
OLC_EVENT
MEAS,
CELL_CODE_
LDR,
CELL_CREDIT
_LDR,
UL_INTRA_FR
EQUENCY_UL
Issue 01 (2013-04-28)
30
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
B,
UL_UU_CLB,
DL_UU_CLB,
CELL_CODE_
CLB,
CELL_CREDIT
_CLB,
DLLOAD_BAS
ED_PCPICH_P
WR_ADJ_SWI
TCH,
ADAPTIVE_R
ACH,
ACK_PRACH_
PREAM_MEA
S,
CAMPING_ST
RATEGY_SWI
TCH
Default
Value:INTRA_
FREQUENCY_
LDB:0,PUC:
0,UL_UU_LDR
:
0,DL_UU_LDR
:
0,UL_UU_OLC
:
0,DL_UU_OLC
:
0,OLC_EVENT
MEAS:
0,CELL_CODE
_LDR:
0,CELL_CRED
IT_LDR:
0,UL_INTRA_
FREQUENCY_
ULB:
0,UL_UU_CLB
:
0,DL_UU_CLB
:
0,CELL_CODE
_CLB:
0,CELL_CRED
Issue 01 (2013-04-28)
31
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
IT_CLB:
0,DLLOAD_B
ASED_PCPICH
_PWR_ADJ_S
WITCH:
0,ADAPTIVE_
RACH:
0,ACK_PRAC
H_PREAM_M
EAS:
0,CAMPING_S
TRATEGY_S
WITCH:0
Issue 01 (2013-04-28)
32
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
NBMLdcAlgoS
witch
BSC6910
ADD
UCELLALGOS
WITCH
WRFD-151203
Camping
Strategy Switch
for Mass Event
Meaning:Wheth
er to enable the
algorithms
related to cell
load control.
Selecting a
switch enables
the
corresponding
algorithm and
clearing a switch
disables the
corresponding
algorithm. 1.
INTRA_FREQ
UENCY_LDB:
Whether to
enable the cell
breathing
algorithm. This
algorithm
adjusts PCPICH transmit
power of a cell
based on the
downlink TCP
load to achieve
load balancing
between intrafrequency cells.
This algorithm
automatically
becomes invalid
when the loadbased dynamic
P-CPICH
transmit power
adjustment
algorithm
(controlled by
the
DLLOAD_BAS
ED_PCPICH_P
WR_ADJ_SWI
TCH switch)
takes effect. 2.
PUC: Whether
to enable the
MOD
UCELLALGOS
WITCH
WRFD-020106
WRFD-150231
WRFD-150219
WRFD-150216
WRFD-150217
WRFD-150215
WRFD-010610
03
WRFD-020102
WRFD-140223
WRFD-150236
WRFD-020101
WRFD-140226
WRFD-020107
WRFD-020104
WRFD-020105
WRFD-020126
WRFD-010612
02
WRFD-020129
WRFD-010626
WRFD-010627
WRFD-020103
WRFD-010660
WRFD-010661
WRFD-010662
WRFD-010663
WRFD-010665
WRFD-140102
WRFD-010660
04
WRFD-010616
06
Issue 01 (2013-04-28)
Load
Reshuffling
RIM Based
UMTS Target
Cell Selection
for LTE
Coverage Based
PS Redirection
from UMTS to
LTE
Load Based PS
Redirection
from UMTS to
LTE
Load Based PS
Handover from
UMTS to LTE
SRVCC from
LTE to UMTS
with PS
Handover
HSDPA
Admission
Control
Load
Measurement
MOCN Cell
Resource
Demarcation
Load Based
Dynamic
Adjustment of
PCPICH
Admission
Control
WRFD-010660
02
Fast Return
from UMTS to
LTE
WRFD-010660
03
Overload
Control
33
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
WRFD-010660
01
Intra Frequency
Load Balance
WRFD-010616
05
Potential User
Control
WRFD-150220
Mobility
Between UMTS
and LTE Phase 1
Potential User
Control (PUC)
algorithm. This
algorithm
adjusts cell
selection and
reselection
parameters
based on the cell
load to enable
UEs to reselect
lightly loaded
cells. 3.
UL_UU_OLC:
Whether to
enable the
uplink overload
control (OLC)
algorithm.
When the uplink
power is
overloaded in a
cell, this
algorithm
alleviates the
uplink load by
using quick
transport format
(TF) restriction,
distributing best
effort (BE)
service to
common
channels, or
releasing UEs.
4.
DL_UU_OLC:
Whether to
enable the
downlink OLC
algorithm.
When the
downlink power
is overloaded in
a cell, this
algorithm
alleviates the
downlink load
WRFD-010616
01
WRFD-010616
03
WRFD-010616
02
WRFD-140217
WRFD-010616
04
WRFD-010616
WRFD-010616
08
WRFD-140218
HSUPA
Admission
Control
PS Service
Redirection
from UMTS to
LTE
MBMS FLC
(Frequency
Layer
Convergence)/
FLD(Frequency
Layer
Dispersion)
FACH
Transmission
Sharing for
MBMS
Inter Frequency
Load Balance
MBMS Phase 2
MBMS over Iur
Dynamic Power
Estimation for
MTCH
MSCH
Scheduling
MBMS Channel
Audience
Rating Statistics
CS Fallback
Guarantee for
LTE Emergency
Calls
Inter-Frequency
Neighboring
Cell Selection
Issue 01 (2013-04-28)
34
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
by using quick
TF restriction,
distributing BE
services to
common
channels,
releasing UEs,
or reconfiguring
the maximum
transmit power
of FACHs. 5.
UL_UU_LDR:
Whether to
enable the
uplink load
reshuffling
(LDR)
algorithm.
When the uplink
load is heavy in
a cell, this
algorithm
alleviates the
uplink load by
using loadbased interfrequency
handovers, BE
service rate
reduction,
uncontrollable
real-time service
QoS
renegotiation,
load-based CS/
PS inter-RAT
handovers, and
AMR service
rate reduction. 6.
DL_UU_LDR:
Whether to
enable the
downlink LDR
algorithm.
When the
downlink load is
heavy in a cell,
this algorithm
Streaming
Service on
MBMS
MBMS P2P
over HSDPA
MBMS
Admission
Enhancement
MBMS
Enhanced
Broadcast Mode
MBMS
Transport
Resource
Management
Coverage Based
PS Handover
from UMTS to
LTE
MBMS
Broadcast Mode
MBMS Load
Control
MBMS
Admission
Control
Inter-Frequency
Load Balancing
Based on
Configurable
Load Threshold
MBMS Soft/
Selective
Combining
MBMS
Introduction
Package
16/32/64/128Kb
ps Channel Rate
on MBMS
Service-Based
PS Handover
Issue 01 (2013-04-28)
35
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
Issue 01 (2013-04-28)
MML
Command
7 Parameters
Feature ID
Feature Name
Description
from UMTS to
LTE
alleviates the
downlink load
by using loadbased interfrequency
handovers, BE
service rate
reduction,
uncontrollable
real-time service
QoS
renegotiation,
load-based CS/
PS inter-RAT
handovers,
AMR service
rate reduction,
and MBMS
power
restriction. 7.
OLC_EVENT
MEAS:
Whether to
enable OLC
event
measurement. 8.
CELL_CODE_
LDR: Whether
to enable cell
code reshuffling
algorithm. In the
event of code
resource
overuse, this
algorithm
alleviates the
code resource
overuse by using
BE service rate
reduction, code
tree reshuffling,
and load-based
inter-frequency
handovers. 9.
CELL_CREDIT
_LDR: Whether
to enable the cell
credit
36
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
reshuffling
algorithm. In the
event of cell
credit overuse,
this algorithm
alleviates the
credit overuse
by using loadbased interfrequency
handovers, BE
service rate
reduction,
uncontrollable
real-time service
QoS
renegotiation,
and load-based
CS/PS interRAT handovers.
10.
UL_INTRA_FR
EQUENCY_UL
B: Whether to
enable RTWPbased intrafrequency load
balancing
algorithm. This
algorithm
adjusts PCPICH transmit
power of a cell
based on the
RTWP load to
achieve load
balancing
between intrafrequency cells.
This algorithm
automatically
becomes invalid
when the loadbased dynamic
P-CPICH
transmit power
adjustment
algorithm
Issue 01 (2013-04-28)
37
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
(controlled by
the
DLLOAD_BAS
ED_PCPICH_P
WR_ADJ_SWI
TCH switch)
takes effect. 11.
UL_UU_CLB:
Whether to
enable the
uplink loadbased CLB
algorithm. This
algorithm
determines
whether a cell
enters the CLB
state by the
uplink load on
the air interface.
If a cell is in the
CLB state,
measurementbased interfrequency
handovers are
triggered
periodically to
achieve load
balancing
between interfrequency cells.
12.
DL_UU_CLB:
Whether to
enable the
downlink loadbased CLB
algorithm. This
algorithm
determines
whether a cell
enters the CLB
state by the
downlink load
on the air
interface. If a
cell is in the
Issue 01 (2013-04-28)
38
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
CLB state,
measurementbased interfrequency
handovers are
triggered
periodically to
achieve load
balancing
between interfrequency cells.
13.
CELL_CODE_
CLB: Whether
to enable code
resource-based
CLB algorithm.
This algorithm
determines
whether a cell
enters the CLB
state by the code
resource usage.
If a cell is in the
CLB state,
measurementbased interfrequency
handovers are
triggered
periodically to
achieve load
balancing
between interfrequency cells.
14.
CELL_CREDIT
_CLB: Whether
to enable creditbased CLB
algorithm. This
algorithm
determines
whether a cell
enters the CLB
state by the
credit resource
usage. If a cell is
Issue 01 (2013-04-28)
39
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
in the CLB state,
measurementbased interfrequency
handovers are
triggered
periodically to
achieve load
balancing
between interfrequency cells.
15.
DLLOAD_BAS
ED_PCPICH_P
WR_ADJ_SWI
TCH: Whether
to enable
downlink loadbased dynamic
primary
common pilot
channel (PCPICH) power
adjustment
algorithm. This
algorithm
adjusts the PCPICH transmit
power by the
downlink nonHSPA power
load to reduce
the downlink
non-HSPA
power load. If
this algorithm
takes effect,
other enabled
algorithms for
intra-frequency
load balancing
(based on TCP
or RTWP)
automatically
become invalid.
16.
ADAPTIVE_R
ACH: Function
Issue 01 (2013-04-28)
40
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
switch for the
adaptive RACH
feature. When
this switch is
turned on, this
feature is
activated. In this
case, the RNC
adjusts the
random access
parameters
based on the
random access
state and on the
uplink power
load of the target
cell. When this
switch is turned
off, this feature
is deactivated.
17.
ACK_PRACH_
PREAM_MEA
S: Whether to
measure the
number of
acknowledged
PRACH
preambles.
When this
switch is turned
on, the RNC
measures the
number of
acknowledged
PRACH
preambles.
When this
switch is turned
off, the RNC
does not
measure the
number of
acknowledged
PRACH
preambles. 18.
CAMPING_ST
RATEGY_SWI
Issue 01 (2013-04-28)
41
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
TCH: Whether
to enable the
camping policy
switching
function when
traffic is heavy.
This is a
function switch
for the function.
When the switch
is turned on, the
camping policy
switching
function is
enabled if traffic
is heavy in the
entire network.
Then, the target
cell is no longer
a preferred
camping cell for
the UE in
question, but a
random
camping cell.
GUI Value
Range:INTRA_
FREQUENCY_
LDB, PUC,
UL_UU_LDR,
DL_UU_LDR,
UL_UU_OLC,
DL_UU_OLC,
OLC_EVENT
MEAS,
CELL_CODE_
LDR,
CELL_CREDIT
_LDR,
UL_INTRA_FR
EQUENCY_UL
B,
UL_UU_CLB,
DL_UU_CLB,
CELL_CODE_
CLB,
CELL_CREDIT
Issue 01 (2013-04-28)
42
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
_CLB,
DLLOAD_BAS
ED_PCPICH_P
WR_ADJ_SWI
TCH,
ADAPTIVE_R
ACH,
ACK_PRACH_
PREAM_MEA
S,
CAMPING_ST
RATEGY_SWI
TCH
Unit:None
Actual Value
Range:INTRA_
FREQUENCY_
LDB, PUC,
UL_UU_LDR,
DL_UU_LDR,
UL_UU_OLC,
DL_UU_OLC,
OLC_EVENT
MEAS,
CELL_CODE_
LDR,
CELL_CREDIT
_LDR,
UL_INTRA_FR
EQUENCY_UL
B,
UL_UU_CLB,
DL_UU_CLB,
CELL_CODE_
CLB,
CELL_CREDIT
_CLB,
DLLOAD_BAS
ED_PCPICH_P
WR_ADJ_SWI
TCH,
ADAPTIVE_R
ACH,
ACK_PRACH_
PREAM_MEA
S,
CAMPING_ST
Issue 01 (2013-04-28)
43
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
RATEGY_SWI
TCH
Default
Value:INTRA_
FREQUENCY_
LDB:0,PUC:
0,UL_UU_LDR
:
0,DL_UU_LDR
:
0,UL_UU_OLC
:
0,DL_UU_OLC
:
0,OLC_EVENT
MEAS:
0,CELL_CODE
_LDR:
0,CELL_CRED
IT_LDR:
0,UL_INTRA_
FREQUENCY_
ULB:
0,UL_UU_CLB
:
0,DL_UU_CLB
:
0,CELL_CODE
_CLB:
0,CELL_CRED
IT_CLB:
0,DLLOAD_B
ASED_PCPICH
_PWR_ADJ_S
WITCH:
0,ADAPTIVE_
RACH:
0,ACK_PRAC
H_PREAM_M
EAS:
0,CAMPING_S
TRATEGY_S
WITCH:0
Issue 01 (2013-04-28)
44
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
IntraFreqLdbPe
riodTimerLen
BSC6900
SET
ULDCPERIOD
WRFD-150236
Load Based
Dynamic
Adjustment of
PCPICH
Meaning:In the
TCP-based
intra-frequency
load balancing
algorithm, this
parameter
specifies the
intra-frequency
load balancing
period. In the
algorithm for
load-based
dynamic
adjustment of
PCPICH, this
parameter
specifies the
load-based
dynamic
adjustment
period of
PCPICH. If a
cell is heavily
loaded, the PCPICH transmit
power is
periodically
reduced so that
UEs in
connected mode
can be more
easily handed
over from the
cell to another
cell.
WRFD-020104
Intra Frequency
Load Balance
GUI Value
Range:
1~115300
Unit:s
Actual Value
Range:
1~115300
Default Value:
1800
Issue 01 (2013-04-28)
45
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
IntraFreqLdbPe
riodTimerLen
BSC6910
SET
ULDCPERIOD
WRFD-150236
Load Based
Dynamic
Adjustment of
PCPICH
Meaning:In the
TCP-based
intra-frequency
load balancing
algorithm, this
parameter
specifies the
intra-frequency
load balancing
period. In the
algorithm for
load-based
dynamic
adjustment of
PCPICH, this
parameter
specifies the
load-based
dynamic
adjustment
period of
PCPICH. If a
cell is heavily
loaded, the PCPICH transmit
power is
periodically
reduced so that
UEs in
connected mode
can be more
easily handed
over from the
cell to another
cell.
WRFD-020104
Intra Frequency
Load Balance
GUI Value
Range:
1~115300
Unit:s
Actual Value
Range:
1~115300
Default Value:
1800
Issue 01 (2013-04-28)
46
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PcpichPwrDow
nDlLoadState
BSC6900
ADD
UCELLLDM
WRFD-150236
Load Based
Dynamic
Adjustment of
PCPICH
Meaning:Downl
ink non-HSPA
power load
status based on
which the
downlink-loadbased dynamic
P-CPICH power
adjustment
algorithm
decreases the PCPICH transmit
power. When
the downlink
non-HSPA
power load
status in a cell is
the same as or
worse than the
status indicated
by the value of
this parameter,
this algorithm
decreases the PCPICH transmit
power by the
step. The
"PCPICHPower
Pace" parameter
in the "ADD
UCELLLDB"
command
specifies the
adjustment step.
The downlink
non-HSPA
power load can
be in either of
the following
states: light state
(DL_LIGHT_S
TATE), normal
state
(DL_NORMAL
_STATE),
loaded state
(DL_LOADED
_STATE),
MOD
UCELLLDM
Issue 01 (2013-04-28)
47
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
heavy state
(DL_HEAVY_
STATE), and
overload state
(DL_OVERRL
OAD_STATE).
Due to load
fluctuation, one
interval is
recommended
between the
value of the
"PcpichPwrDownDlLoadSt
ate" parameter
and the value of
the
"PcpichPwrUp
DlLoadState"
parameter. For
example, when
the value of the
"PcpichPwrUp
DlLoadState"
parameter is set
to
DL_LIGHT_ST
ATE, the
"PcpichPwrDownDlLoadSt
ate" parameter
must be set to
DL_LOADED_
STATE. The
state interval
prevents
frequently
increasing or
decreasing PCPICH transmit
power. The
recommended
value is
DL_LOADED_
STATE for
HSDPA cells.
The
recommended
Issue 01 (2013-04-28)
48
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
value is
DL_HEAVY_S
TATE for R99
cells. The
downlink nonHSPA power
load state
transition
process is as
follows: If the
downlink nonHSPA power
load in the light
state is larger
than 30%+10%,
transition from
light state to
normal state is
triggered. If the
downlink nonHSPA power
load in the
normal state is
smaller than
30%-10%,
transition from
normal state to
light state is
triggered; if the
downlink nonHSPA power
load in the
normal state is
larger than 50%
+10%, transition
from normal
state to loaded
state is
triggered. If the
downlink nonHSPA power
load in the
loaded state is
smaller than
50%-10%,
transition from
loaded state to
normal state is
Issue 01 (2013-04-28)
49
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
triggered; if the
downlink nonHSPA power
load in the
loaded state is
larger than 50%
+10%, transition
from loaded
state to heavy
state is
triggered. If the
downlink nonHSPA power
load in the heavy
state is smaller
than 70%-10%,
transition from
heavy state to
loaded state is
triggered; if the
downlink nonHSPA power
load in the
overload state is
smaller than
95%-10%,
transition from
overload state to
heavy state is
triggered. The
downlink nonHSPA power
load is as
follows:Downli
nk load in an
HSDPA cell is
the proportion of
non-HSPA
power
consumption to
the maximum
transmit power
of this cell
MaxTxPower;
Downlink load
in an R99 cell is
the proportion of
TCP to the
Issue 01 (2013-04-28)
50
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
maximum
transmit power
of this cell.
GUI Value
Range:DL_LIG
HT_STATE,
DL_NORMAL
_STATE,
DL_LOADED_
STATE,
DL_HEAVY_S
TATE,
DL_OVERRLO
AD_STATE
Unit:None
Actual Value
Range:DL_LIG
HT_STATE,
DL_NORMAL
_STATE,
DL_LOADED_
STATE,
DL_HEAVY_S
TATE,
DL_OVERRLO
AD_STATE
Default
Value:DL_LOA
DED_STATE
Issue 01 (2013-04-28)
51
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PcpichPwrDow
nDlLoadState
BSC6910
ADD
UCELLLDM
WRFD-150236
Load Based
Dynamic
Adjustment of
PCPICH
Meaning:Downl
ink non-HSPA
power load
status based on
which the
downlink-loadbased dynamic
P-CPICH power
adjustment
algorithm
decreases the PCPICH transmit
power. When
the downlink
non-HSPA
power load
status in a cell is
the same as or
worse than the
status indicated
by the value of
this parameter,
this algorithm
decreases the PCPICH transmit
power by the
step. The
"PCPICHPower
Pace" parameter
in the "ADD
UCELLLDB"
command
specifies the
adjustment step.
The downlink
non-HSPA
power load can
be in either of
the following
states: light state
(DL_LIGHT_S
TATE), normal
state
(DL_NORMAL
_STATE),
loaded state
(DL_LOADED
_STATE),
MOD
UCELLLDM
Issue 01 (2013-04-28)
52
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
heavy state
(DL_HEAVY_
STATE), and
overload state
(DL_OVERRL
OAD_STATE).
Due to load
fluctuation, one
interval is
recommended
between the
value of the
"PcpichPwrDownDlLoadSt
ate" parameter
and the value of
the
"PcpichPwrUp
DlLoadState"
parameter. For
example, when
the value of the
"PcpichPwrUp
DlLoadState"
parameter is set
to
DL_LIGHT_ST
ATE, the
"PcpichPwrDownDlLoadSt
ate" parameter
must be set to
DL_LOADED_
STATE. The
state interval
prevents
frequently
increasing or
decreasing PCPICH transmit
power. The
recommended
value is
DL_LOADED_
STATE for
HSDPA cells.
The
recommended
Issue 01 (2013-04-28)
53
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
value is
DL_HEAVY_S
TATE for R99
cells. The
downlink nonHSPA power
load state
transition
process is as
follows: If the
downlink nonHSPA power
load in the light
state is larger
than 30%+10%,
transition from
light state to
normal state is
triggered. If the
downlink nonHSPA power
load in the
normal state is
smaller than
30%-10%,
transition from
normal state to
light state is
triggered; if the
downlink nonHSPA power
load in the
normal state is
larger than 50%
+10%, transition
from normal
state to loaded
state is
triggered. If the
downlink nonHSPA power
load in the
loaded state is
smaller than
50%-10%,
transition from
loaded state to
normal state is
Issue 01 (2013-04-28)
54
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
triggered; if the
downlink nonHSPA power
load in the
loaded state is
larger than 50%
+10%, transition
from loaded
state to heavy
state is
triggered. If the
downlink nonHSPA power
load in the heavy
state is smaller
than 70%-10%,
transition from
heavy state to
loaded state is
triggered; if the
downlink nonHSPA power
load in the
overload state is
smaller than
95%-10%,
transition from
overload state to
heavy state is
triggered. The
downlink nonHSPA power
load is as
follows:Downli
nk load in an
HSDPA cell is
the proportion of
non-HSPA
power
consumption to
the maximum
transmit power
of this cell
MaxTxPower;
Downlink load
in an R99 cell is
the proportion of
TCP to the
Issue 01 (2013-04-28)
55
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
maximum
transmit power
of this cell.
GUI Value
Range:DL_LIG
HT_STATE,
DL_NORMAL
_STATE,
DL_LOADED_
STATE,
DL_HEAVY_S
TATE,
DL_OVERRLO
AD_STATE
Unit:None
Actual Value
Range:DL_LIG
HT_STATE,
DL_NORMAL
_STATE,
DL_LOADED_
STATE,
DL_HEAVY_S
TATE,
DL_OVERRLO
AD_STATE
Default
Value:DL_LOA
DED_STATE
Issue 01 (2013-04-28)
56
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PCPICHPowerP
ace
BSC6900
ADD
UCELLLDB
WRFD-150236
Load Based
Dynamic
Adjustment of
PCPICH
Meaning:Step at
which the
CPICH power is
adjusted each
time. This
parameter is
used for loadbased dynamic
pilot power
adjustment and
TCP-based
intra-frequency
load balancing.
For detailed
information
about this
parameter, see
3GPP TS
25.433.
MOD
UCELLLDB
WRFD-020104
Intra Frequency
Load Balance
GUI Value
Range:0~100
Unit:0.1dB
Actual Value
Range:0~10
Default Value:2
Issue 01 (2013-04-28)
57
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PCPICHPowerP
ace
BSC6910
ADD
UCELLLDB
WRFD-150236
Load Based
Dynamic
Adjustment of
PCPICH
Meaning:Step at
which the
CPICH power is
adjusted each
time. This
parameter is
used for loadbased dynamic
pilot power
adjustment and
TCP-based
intra-frequency
load balancing.
For detailed
information
about this
parameter, see
3GPP TS
25.433.
WRFD-020104
MOD
UCELLLDB
Intra Frequency
Load Balance
GUI Value
Range:0~100
Unit:0.1dB
Actual Value
Range:0~10
Default Value:2
MinPCPICHPo
wer
BSC6900
ADD UPCPICH
WRFD-150236
MOD
UPCPICHPWR
WRFD-020104
WRFD-020501
Load Based
Dynamic
Adjustment of
PCPICH
Intra Frequency
Load Balance
Open Loop
Power Control
Meaning:Minim
um TX power of
the PCPICH in a
cell. This
parameter
defines the
minimum
coverage area of
a cell.
GUI Value
Range:-100~50
0
Unit:0.1dBm
Actual Value
Range:-10~50
Default Value:
313
Issue 01 (2013-04-28)
58
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
MinPCPICHPo
wer
BSC6910
ADD UPCPICH
WRFD-150236
MOD
UPCPICHPWR
WRFD-020104
Load Based
Dynamic
Adjustment of
PCPICH
Meaning:Minim
um TX power of
the PCPICH in a
cell. This
parameter
defines the
minimum
coverage area of
a cell.
WRFD-020501
Intra Frequency
Load Balance
Open Loop
Power Control
GUI Value
Range:-100~50
0
Unit:0.1dBm
Actual Value
Range:-10~50
Default Value:
313
Issue 01 (2013-04-28)
59
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PCPICHPower
BSC6900
ADD UPCPICH
WRFD-150236
MOD UCELL
WRFD-020104
Load Based
Dynamic
Adjustment of
PCPICH
Meaning:TX
power of the PCPICH in a cell.
This parameter
should be set
based on the
actual system
environment
such as cell
coverage
(radius) and
geographical
environment.
For the cells to
be covered, the
downlink
coverage must
be guaranteed.
For the cells
requiring soft
handover area,
this parameter
should satisfy
the proportion of
soft handover
areas stipulated
in the network
plan. For
detailed
information
about this
parameter, see
3GPP TS
25.433.
WRFD-020501
Intra Frequency
Load Balance
Open Loop
Power Control
GUI Value
Range:-100~50
0
Unit:0.1dBm
Actual Value
Range:-10~50
Default Value:
330
Issue 01 (2013-04-28)
60
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PCPICHPower
BSC6910
ADD UPCPICH
WRFD-150236
MOD UCELL
WRFD-020104
Load Based
Dynamic
Adjustment of
PCPICH
Meaning:TX
power of the PCPICH in a cell.
This parameter
should be set
based on the
actual system
environment
such as cell
coverage
(radius) and
geographical
environment.
For the cells to
be covered, the
downlink
coverage must
be guaranteed.
For the cells
requiring soft
handover area,
this parameter
should satisfy
the proportion of
soft handover
areas stipulated
in the network
plan. For
detailed
information
about this
parameter, see
3GPP TS
25.433.
WRFD-020501
Intra Frequency
Load Balance
Open Loop
Power Control
GUI Value
Range:-100~50
0
Unit:0.1dBm
Actual Value
Range:-10~50
Default Value:
330
Issue 01 (2013-04-28)
61
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PcpichPwrUpDl
LoadState
BSC6900
ADD
UCELLLDM
WRFD-150236
Load Based
Dynamic
Adjustment of
PCPICH
Meaning:Downl
ink non-HSPA
power load
status based on
which the
downlink-loadbased dynamic
P-CPICH power
adjustment
algorithm
increases the PCPICH transmit
power. When
the downlink
non-HSPA
power load
status in a cell is
the same as or
better than the
status indicated
by the value of
this parameter,
this algorithm
increases the PCPICH transmit
power by the
step. The
"PCPICHPower
Pace" parameter
in the "ADD
UCELLLDB"
command
specifies the
adjustment step.
The downlink
non-HSPA
power load can
be in either of
the following
states: light state
(DL_LIGHT_S
TATE), normal
state
(DL_NORMAL
_STATE),
loaded state
(DL_LOADED
_STATE),
MOD
UCELLLDM
Issue 01 (2013-04-28)
62
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
heavy state
(DL_HEAVY_
STATE), and
overload state
(DL_OVERRL
OAD_STATE).
Due to load
fluctuation, one
interval is
recommended
between the
value of the
"PcpichPwrDownDlLoadSt
ate" parameter
and the value of
the
"PcpichPwrUp
DlLoadState"
parameter. For
example, when
the value of the
"PcpichPwrUp
DlLoadState"
parameter is set
to
DL_LIGHT_ST
ATE, the
"PcpichPwrDownDlLoadSt
ate" parameter
must be set to
DL_LOADED_
STATE. The
state interval
prevents
frequently
increasing or
decreasing PCPICH transmit
power. The
recommended
value is
DL_LIGHT_ST
ATE for
HSDPA cells.
The
recommended
Issue 01 (2013-04-28)
63
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
value is
DL_NORMAL
_STATE for
R99 cells. The
downlink nonHSPA power
load state
transition
process is as
follows: If the
downlink nonHSPA power
load in the light
state is larger
than 30%+10%,
transition from
light state to
normal state is
triggered. If the
downlink nonHSPA power
load in the
normal state is
smaller than
30%-10%,
transition from
normal state to
light state is
triggered; if the
downlink nonHSPA power
load in the
normal state is
larger than 50%
+10%, transition
from normal
state to loaded
state is
triggered. If the
downlink nonHSPA power
load in the
loaded state is
smaller than
50%-10%,
transition from
loaded state to
normal state is
Issue 01 (2013-04-28)
64
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
triggered; if the
downlink nonHSPA power
load in the
loaded state is
larger than 50%
+10%, transition
from loaded
state to heavy
state is
triggered. If the
downlink nonHSPA power
load in the heavy
state is smaller
than 70%-10%,
transition from
heavy state to
loaded state is
triggered; if the
downlink nonHSPA power
load in the
overload state is
smaller than
95%-10%,
transition from
overload state to
heavy state is
triggered. The
downlink nonHSPA power
load is as
follows:Downli
nk load in an
HSDPA cell is
the proportion of
non-HSPA
power
consumption to
the maximum
transmit power
of this cell
MaxTxPower;
Downlink load
in an R99 cell is
the proportion of
TCP to the
Issue 01 (2013-04-28)
65
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
maximum
transmit power
of this cell.
GUI Value
Range:DL_LIG
HT_STATE,
DL_NORMAL
_STATE,
DL_LOADED_
STATE,
DL_HEAVY_S
TATE,
DL_OVERRLO
AD_STATE
Unit:None
Actual Value
Range:DL_LIG
HT_STATE,
DL_NORMAL
_STATE,
DL_LOADED_
STATE,
DL_HEAVY_S
TATE,
DL_OVERRLO
AD_STATE
Default
Value:DL_LIG
HT_STATE
Issue 01 (2013-04-28)
66
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PcpichPwrUpDl
LoadState
BSC6910
ADD
UCELLLDM
WRFD-150236
Load Based
Dynamic
Adjustment of
PCPICH
Meaning:Downl
ink non-HSPA
power load
status based on
which the
downlink-loadbased dynamic
P-CPICH power
adjustment
algorithm
increases the PCPICH transmit
power. When
the downlink
non-HSPA
power load
status in a cell is
the same as or
better than the
status indicated
by the value of
this parameter,
this algorithm
increases the PCPICH transmit
power by the
step. The
"PCPICHPower
Pace" parameter
in the "ADD
UCELLLDB"
command
specifies the
adjustment step.
The downlink
non-HSPA
power load can
be in either of
the following
states: light state
(DL_LIGHT_S
TATE), normal
state
(DL_NORMAL
_STATE),
loaded state
(DL_LOADED
_STATE),
MOD
UCELLLDM
Issue 01 (2013-04-28)
67
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
heavy state
(DL_HEAVY_
STATE), and
overload state
(DL_OVERRL
OAD_STATE).
Due to load
fluctuation, one
interval is
recommended
between the
value of the
"PcpichPwrDownDlLoadSt
ate" parameter
and the value of
the
"PcpichPwrUp
DlLoadState"
parameter. For
example, when
the value of the
"PcpichPwrUp
DlLoadState"
parameter is set
to
DL_LIGHT_ST
ATE, the
"PcpichPwrDownDlLoadSt
ate" parameter
must be set to
DL_LOADED_
STATE. The
state interval
prevents
frequently
increasing or
decreasing PCPICH transmit
power. The
recommended
value is
DL_LIGHT_ST
ATE for
HSDPA cells.
The
recommended
Issue 01 (2013-04-28)
68
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
value is
DL_NORMAL
_STATE for
R99 cells. The
downlink nonHSPA power
load state
transition
process is as
follows: If the
downlink nonHSPA power
load in the light
state is larger
than 30%+10%,
transition from
light state to
normal state is
triggered. If the
downlink nonHSPA power
load in the
normal state is
smaller than
30%-10%,
transition from
normal state to
light state is
triggered; if the
downlink nonHSPA power
load in the
normal state is
larger than 50%
+10%, transition
from normal
state to loaded
state is
triggered. If the
downlink nonHSPA power
load in the
loaded state is
smaller than
50%-10%,
transition from
loaded state to
normal state is
Issue 01 (2013-04-28)
69
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
triggered; if the
downlink nonHSPA power
load in the
loaded state is
larger than 50%
+10%, transition
from loaded
state to heavy
state is
triggered. If the
downlink nonHSPA power
load in the heavy
state is smaller
than 70%-10%,
transition from
heavy state to
loaded state is
triggered; if the
downlink nonHSPA power
load in the
overload state is
smaller than
95%-10%,
transition from
overload state to
heavy state is
triggered. The
downlink nonHSPA power
load is as
follows:Downli
nk load in an
HSDPA cell is
the proportion of
non-HSPA
power
consumption to
the maximum
transmit power
of this cell
MaxTxPower;
Downlink load
in an R99 cell is
the proportion of
TCP to the
Issue 01 (2013-04-28)
70
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
maximum
transmit power
of this cell.
GUI Value
Range:DL_LIG
HT_STATE,
DL_NORMAL
_STATE,
DL_LOADED_
STATE,
DL_HEAVY_S
TATE,
DL_OVERRLO
AD_STATE
Unit:None
Actual Value
Range:DL_LIG
HT_STATE,
DL_NORMAL
_STATE,
DL_LOADED_
STATE,
DL_HEAVY_S
TATE,
DL_OVERRLO
AD_STATE
Default
Value:DL_LIG
HT_STATE
Issue 01 (2013-04-28)
71
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
MaxPCPICHPo
wer
BSC6900
ADD UPCPICH
WRFD-150236
MOD
UPCPICHPWR
WRFD-020104
Load Based
Dynamic
Adjustment of
PCPICH
Meaning:Maxi
mum TX power
of the PCPICH
in a cell. This
parameter
defines the
maximum
coverage area of
a cell.
WRFD-020501
Intra Frequency
Load Balance
Open Loop
Power Control
GUI Value
Range:-100~50
0
Unit:0.1dBm
Actual Value
Range:-10~50
Default Value:
346
MaxPCPICHPo
wer
BSC6910
ADD UPCPICH
WRFD-150236
MOD
UPCPICHPWR
WRFD-020104
WRFD-020501
Load Based
Dynamic
Adjustment of
PCPICH
Intra Frequency
Load Balance
Open Loop
Power Control
Meaning:Maxi
mum TX power
of the PCPICH
in a cell. This
parameter
defines the
maximum
coverage area of
a cell.
GUI Value
Range:-100~50
0
Unit:0.1dBm
Actual Value
Range:-10~50
Default Value:
346
Issue 01 (2013-04-28)
72
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
RlMinDlPwr
BSC6900
ADD
UCELLRLPW
R
WRFD-020501
Open Loop
Power Control
Meaning:Minim
al transmit
power of a
downlink radio
link. For details
about this
parameter, see
3GPP TS
25.433.
MOD
UCELLRLPW
R
GUI Value
Range:-350~15
0
Unit:0.1dB
Actual Value
Range:-35~15
Default
Value:None
RlMinDlPwr
BSC6910
ADD
UCELLRLPW
R
WRFD-020501
Open Loop
Power Control
MOD
UCELLRLPW
R
Meaning:Minim
al transmit
power of a
downlink radio
link. For details
about this
parameter, see
3GPP TS
25.433.
GUI Value
Range:-350~15
0
Unit:0.1dB
Actual Value
Range:-35~15
Default
Value:None
Issue 01 (2013-04-28)
73
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
RlMaxDlPwr
BSC6900
ADD
UCELLRLPW
R
WRFD-140205
Voice Service
Experience
Improvement
for Weak
Reception Ues
Meaning:Maxi
mum transmit
power of a
downlink radio
link. For details
about this
parameter, see
3GPP TS
25.433.
WRFD-020501
MOD
UCELLRLPW
R
Open Loop
Power Control
GUI Value
Range:-350~15
0
Unit:0.1dB
Actual Value
Range:-35~15
Default
Value:None
RlMaxDlPwr
BSC6910
ADD
UCELLRLPW
R
MOD
UCELLRLPW
R
WRFD-140205
WRFD-020501
Voice Service
Experience
Improvement
for Weak
Reception Ues
Open Loop
Power Control
Meaning:Maxi
mum transmit
power of a
downlink radio
link. For details
about this
parameter, see
3GPP TS
25.433.
GUI Value
Range:-350~15
0
Unit:0.1dB
Actual Value
Range:-35~15
Default
Value:None
Issue 01 (2013-04-28)
74
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
MaxTxPower
BSC6900
ADD
UCELLSETUP
WRFD-020501
Open Loop
Power Control
Meaning:Sum
of the maximum
transmit power
of all DL
channels in a
cell. For detailed
information of
this parameter,
see 3GPP TS
25.433.
MOD UCELL
GUI Value
Range:0~500
Unit:0.1dBm
Actual Value
Range:0~50
Default Value:
430
MaxTxPower
BSC6910
ADD
UCELLSETUP
WRFD-020501
Open Loop
Power Control
MOD UCELL
Meaning:Sum
of the maximum
transmit power
of all DL
channels in a
cell. For detailed
information of
this parameter,
see 3GPP TS
25.433.
GUI Value
Range:0~500
Unit:0.1dBm
Actual Value
Range:0~50
Default Value:
430
Issue 01 (2013-04-28)
75
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
FuncSwitch2
BSC6900
ADD
UCELLLICEN
SE
WRFD-151203
Camping
Strategy Switch
for Mass Event
Meaning:
1.BASED_UE_
LOC_DRD_SW
ITCH: Whether
the function of
UE locationbased multifrequency-band
DRD is
available. When
the conditions of
path loss are
met, cell edge
UEs in a highfrequency-band
cell perform the
DRD procedure
towards a lowfrequency-band
cell, or cell
center UEs in a
low-frequencyband cell
perform the
DRD procedure
towards a highfrequency-band
cell. The
function of UE
location-based
multifrequency-band
DRD takes
effect only when
this parameter is
turned on and
the
"BasedUELocD
RDSwitch"
parameter in the
"SET UDRD" or
"ADD
UCELLDRD"
command is also
turned on. 2.
LOAD_BASED
_PCPICH_PW
R_ADJ:
MOD
UCELLLICEN
SE
WRFD-150236
WRFD-151201
WRFD-150232
WRFD-150246
Load Based
Dynamic
Adjustment of
PCPICH
Adaptive RACH
Multiband
Direct Retry
Based on UE
Location
Service Steering
and Load
Sharing in
CELL_FACH
State
Issue 01 (2013-04-28)
76
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
Whether the
license function
switch for Load
Based Dynamic
Adjustment of
PCPICH is
enabled. 3.
ADAPTIVE_R
ACH_SWITCH
(License Switch
for Adaptive
RACH): Celllevel license
switch for the
adaptive RACH
feature. When
this switch is
turned on, the
adaptive RACH
is activated.
When this
switch is turned
off, this feature
is deactivated. 4.
CAMPING_ST
RATEGY_SWI
TCH(Switch for
Camp Policy
Switching in
Heavy Traffic):
Whether to
enable the
camping policy
switching
function when
traffic is heavy.
This is a license
switch for the
function. When
the switch is
turned on, the
camping policy
switching
function is
enabled if traffic
is heavy in the
entire network.
Then, the target
Issue 01 (2013-04-28)
77
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
cell is no longer
a preferred
camping cell for
the UE in
question, but a
random
camping cell. 5.
FACH_POOL_
SWITCH:
Function switch
for the FACH
Pool feature.
When this
switch is turned
on, the FACH
Pool feature is
activated and the
P2F-triggered
redirection
algorithm is also
activated. Note
that P2F
indicates a
CELL_PCH/
URA_PCH-toCELL_FACH
state transition.
6.
FACH_TRAFF
_STEER_AND
_LOAD_SHAR
E_SWITCH:
Function switch
for the Service
Steering and
Load Sharing in
CELL_FACH
State feature.
When this
switch is turned
on, this feature is
activated. This
feature
incorporates the
P2F-triggered
redirection
algorithm for
real-time
Issue 01 (2013-04-28)
78
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
services, the
P2F-triggered
redirection
algorithm for
non-real-time
services, and the
algorithm of
P2F-triggered
redirection in
case of P2D
failures for realtime services.
GUI Value
Range:BASED_
UE_LOC_DRD
_SWITCH,
LOAD_BASED
_PCPICH_PW
R_ADJ,
ADAPTIVE_R
ACH_SWITCH
,
CAMPING_ST
RATEGY_SWI
TCH,
FACH_POOL_
SWITCH,
FACH_TRAFF
_STEER_AND
_LOAD_SHAR
E_SWITCH
Unit:None
Actual Value
Range:BASED_
UE_LOC_DRD
_SWITCH,
LOAD_BASED
_PCPICH_PW
R_ADJ,
ADAPTIVE_R
ACH_SWITCH
,
CAMPING_ST
RATEGY_SWI
TCH,
FACH_POOL_
SWITCH,
Issue 01 (2013-04-28)
79
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
FACH_TRAFF
_STEER_AND
_LOAD_SHAR
E_SWITCH
Default
Value:BASED_
UE_LOC_DRD
_SWITCH:
0,LOAD_BASE
D_PCPICH_P
WR_ADJ:
0,ADAPTIVE_
RACH_SWITC
H:
0,CAMPING_S
TRATEGY_S
WITCH:
0,FACH_POOL
_SWITCH:
0,FACH_TRAF
F_STEER_AN
D_LOAD_SHA
RE_SWITCH:0
Issue 01 (2013-04-28)
80
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
7 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
FuncSwitch2
BSC6910
ADD
UCELLLICEN
SE
WRFD-151203
Camping
Strategy Switch
for Mass Event
Meaning:
1.BASED_UE_
LOC_DRD_SW
ITCH: Whether
the function of
UE locationbased multifrequency-band
DRD is
available. When
the conditions of
path loss are
met, cell edge
UEs in a highfrequency-band
cell perform the
DRD procedure
towards a lowfrequency-band
cell, or cell
center UEs in a
low-frequencyband cell
perform the
DRD procedure
towards a highfrequency-band
cell. The
function of UE
location-based
multifrequency-band
DRD takes
effect only when
this parameter is
turned on and
the
"BasedUELocD
RDSwitch"
parameter in the
"SET UDRD" or
"ADD
UCELLDRD"
command is also
turned on. 2.
LOAD_BASED
_PCPICH_PW
R_ADJ:
MOD
UCELLLICEN
SE
WRFD-150236
WRFD-151201
WRFD-150232
WRFD-150246
Load Based
Dynamic
Adjustment of
PCPICH
Adaptive RACH
Multiband
Direct Retry
Based on UE
Location
Service Steering
and Load
Sharing in
CELL_FACH
State
Issue 01 (2013-04-28)
81
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
Whether the
license function
switch for Load
Based Dynamic
Adjustment of
PCPICH is
enabled. 3.
ADAPTIVE_R
ACH_SWITCH
(License Switch
for Adaptive
RACH): Celllevel license
switch for the
adaptive RACH
feature. When
this switch is
turned on, the
adaptive RACH
is activated.
When this
switch is turned
off, this feature
is deactivated. 4.
CAMPING_ST
RATEGY_SWI
TCH(Switch for
Camp Policy
Switching in
Heavy Traffic):
Whether to
enable the
camping policy
switching
function when
traffic is heavy.
This is a license
switch for the
function. When
the switch is
turned on, the
camping policy
switching
function is
enabled if traffic
is heavy in the
entire network.
Then, the target
Issue 01 (2013-04-28)
82
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
cell is no longer
a preferred
camping cell for
the UE in
question, but a
random
camping cell. 5.
FACH_POOL_
SWITCH:
Function switch
for the FACH
Pool feature.
When this
switch is turned
on, the FACH
Pool feature is
activated and the
P2F-triggered
redirection
algorithm is also
activated. Note
that P2F
indicates a
CELL_PCH/
URA_PCH-toCELL_FACH
state transition.
6.
FACH_TRAFF
_STEER_AND
_LOAD_SHAR
E_SWITCH:
Function switch
for the Service
Steering and
Load Sharing in
CELL_FACH
State feature.
When this
switch is turned
on, this feature is
activated. This
feature
incorporates the
P2F-triggered
redirection
algorithm for
real-time
Issue 01 (2013-04-28)
83
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
services, the
P2F-triggered
redirection
algorithm for
non-real-time
services, and the
algorithm of
P2F-triggered
redirection in
case of P2D
failures for realtime services.
GUI Value
Range:BASED_
UE_LOC_DRD
_SWITCH,
LOAD_BASED
_PCPICH_PW
R_ADJ,
ADAPTIVE_R
ACH_SWITCH
,
CAMPING_ST
RATEGY_SWI
TCH,
FACH_POOL_
SWITCH,
FACH_TRAFF
_STEER_AND
_LOAD_SHAR
E_SWITCH
Unit:None
Actual Value
Range:BASED_
UE_LOC_DRD
_SWITCH,
LOAD_BASED
_PCPICH_PW
R_ADJ,
ADAPTIVE_R
ACH_SWITCH
,
CAMPING_ST
RATEGY_SWI
TCH,
FACH_POOL_
SWITCH,
Issue 01 (2013-04-28)
84
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
Parameter ID
NE
MML
Command
7 Parameters
Feature ID
Feature Name
Description
FACH_TRAFF
_STEER_AND
_LOAD_SHAR
E_SWITCH
Default
Value:BASED_
UE_LOC_DRD
_SWITCH:
0,LOAD_BASE
D_PCPICH_P
WR_ADJ:
0,ADAPTIVE_
RACH_SWITC
H:
0,CAMPING_S
TRATEGY_S
WITCH:
0,FACH_POOL
_SWITCH:
0,FACH_TRAF
F_STEER_AN
D_LOAD_SHA
RE_SWITCH:0
Issue 01 (2013-04-28)
85
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
8 Counters
Counters
Issue 01 (2013-04-28)
86
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
9 Glossary
Glossary
Issue 01 (2013-04-28)
87
WCDMA RAN
Load Based Dynamic Adjustment of PCPICH Feature
Parameter Description
10
10 Reference Documents
Reference Documents
1.
2.
3.
Issue 01 (2013-04-28)
88