Académique Documents
Professionnel Documents
Culture Documents
VBA24001-R.3783.A
logo_Q0770
VBA24001
081219_Gdesign_ito
REPAIR MANUAL
Disassembly ................................................................................................................................................................................ D2
1. External section ............................................................................................................................................................... D2
Bottom cover .................................................................................................................................................................. D2
Removal of back cover .................................................................................................................................................. D4
2. Back cover ........................................................................................................................................................................ D6
Sponge/Button/FPC/Speaker....................................................................................................................................... D8
SD cover unit ............................................................................................................................................................... D10
SD cover........................................................................................................................................................................ D11
TFT monitor unit ....................................................................................................................................................... D12
3. Front cover ..................................................................................................................................................................... D18
Pop-up of Flash unit (SB) ........................................................................................................................................... D18
Front cover ................................................................................................................................................................... D18
4. Top cover ........................................................................................................................................................................ D19
TOGO PCB unit .......................................................................................................................................................... D19
Removal of top cover................................................................................................................................................... D20
SB upper cover............................................................................................................................................................ D21
Assembly/Adjustment ............................................................................................................................................................... A1
1. Front body ....................................................................................................................................................................... A1
Mirror unit .................................................................................................................................................................... A1
Aperture lever section ................................................................................................................................................... A2
Spring hooking position ................................................................................................................................................ A2
F-min SW section........................................................................................................................................................... A3
Release button unit ....................................................................................................................................................... A3
plate ............................................................................................................................................................................... A4
Inside finder LCD unit ................................................................................................................................................. A4
Wiring ......................................................................................................................................................................................... E1
Inspection standards.................................................................................................................................................................. R1
Tools ............................................................................................................................................................................................ T1
- D5000 -
INC
VBA24001-R.3783.A
! WARNING
There are high voltege parts inside. Be careful of this electric shock,
when you remove the cover.
Caution:
In disassembly/(re)assembly, be sure to use conductive mat (J5033) and wrist strap (J5033-5), in
order to protect electric parts from static electricity.
Before disassembling, be sure to remove batteries or AC power cord.
In disassembling, be sure to memorize the processing state of wires and FPC, screws to be fixed and
their types, etc.
The low-pass filter of the image PCB/base plate is easily damaged. Handle it very carefully.
Caution:
When "Separation of Front body from Rear body", "Disassembly of Image sensor unit"
and "Disassembly of Bayonet" are performed, be sure to carry out "RESET AF-DEFOCUS
COMPENSATION" of the D5000 adjustment software after assembly.
- D1 D5000 -
INC
VBA24001-R.3783.A
Disassembly
1. External section
Bottom cover
Open and tilt the battery cover unit (#B151) at approx. 35 angle, then pull it out at the angle.
Open the power cable cover.
Take out the four screws (#735) and five screws (#671).
Remove the bottom cover (#25).
Approx. 35
#671
#25
#735
Power cable cover
#735
- D2 D5000 -
INC
VBA24001-R.3783.A
! WARNING
There are high voltege parts inside. Be careful of this electric shock,
when you remove the cover.
2K /5W
- D3 D5000 -
INC
VBA24001-R.3783.A
#618
#697 #690
#740
- D4 D5000 -
INC
VBA24001-R.3783.A
Remove the cover by lifting it at the grip side first, and then the whole.
Disconnect the FPC and harness (of the rear cover) from the connectors of the TOGO PCB UNIT(#B2001).
#71
- D5 D5000 -
INC
VBA24001-R.3783.A
2. Back cover
Peel off the tape (#705).
#705
#741
#446 #445
- D6 D5000 -
INC
VBA24001-R.3783.A
Take out the two screws (#682).
Remove the TFT monitor unit from the back cover.
When removing this, be careful not to catch the harness.)
#682
- D7 D5000 -
INC
VBA24001-R.3783.A
Sponge/Button/FPC/Speaker
#478
#424
#425
#426
#427 #421
#471
#472 #422
#475
#474
#1047
#683
#412
#418
#B1019 #419
#413
#683
#707
#415
#729
- D8 D5000 -
INC
VBA24001-R.3783.A
Peel off the tape (#477).
Peel off the tape (#706).
Remove the superglue from the SD access lamp window (#408), and remove [#408].
#706
#477
#408
Adhesive: Superglue
#473
#469
#470
#476
- D9 D5000 -
INC
VBA24001-R.3783.A
SD cover unit
#B443
#448
- D10 D5000 -
INC
VBA24001-R.3783.A
SD cover
Take out the two screws, and remove the SD-cover click spring.
Pull out the shaft, and remove the SD-cover torsion spring. (Be careful NOT to lose the spring.)
Remove the plate from the SD cover (#443).
Shaft
Plate
#443
- D11 D5000 -
INC
VBA24001-R.3783.A
TFT monitor unit
Remove the TFT window (#402), and peel off the TFT window double-sticking tape (#403).
Remove the sensor magnet (#490) from the TFT monitor unit (#B2049).
Remove the magnet spacer (#494) from the sensor magnet (#490).
#402
#403 #490
#494
#B2049
- D12 D5000 -
INC
VBA24001-R.3783.A
Take out the screw (#671).
Release the two inside hooks of the hinge bottom cover (#438), and remove the hinge top cover (#437).
(Caution : must be exercised that each part do not get scratched or dented. If it does, use a new one.)
#671
#438
#437
Position [#B454] as below, and take out the two screws (#673) and two screws (#674).
#673
#B454
#674
- D13 D5000 -
INC
VBA24001-R.3783.A
Release the three hooks, and remove the TFT top cover (#434).
[When removing this, be careful NOT to lose the lock-plate spring (#432) and lock knob (#431).]
(Caution : must be exercised that each part does not get scratched or dented. If it does, use a new one.)
Back
#434
#432
#431
- D14 D5000 -
INC
VBA24001-R.3783.A
Take out the screw (#677).
Remove the hinge bottom cover (#438).
(Caution must be exercised that the part does not get scratched or dented. If it does, use a new one.)
#438
#677
[Orange/Blue/Black/Red]
#B454
- D15 D5000 -
INC
VBA24001-R.3783.A
#1058
#B454
#406
- D16 D5000 -
INC
VBA24001-R.3783.A
Remove the TFT monitor unit (#B1049).
#B1049
- D17 D5000 -
INC
VBA24001-R.3783.A
3. Front cover
Pop-up of Flash unit (SB)
Cut the lumirror sheet, etc, into the below size, and inset it in the clearance of the top cover pop-up
section. Then, slide it in the direction of the arrow and raise (pop-up) the flash unit.
Approx. 2cm
Approx. 4cm
Front cover
Take out the four screws (#610) and the one screw (#626).
Remove the front cover unit (#B24).
#610
#610
#466
#626
#B24
#465
- D18 D5000 -
INC
VBA24001-R.3783.A
4. Top cover
TOGO PCB unit
Disconnect the seven FPCs, and remove the harness from the connector.
Unsolder the wires in the upper right [Red], upper left [Black/Red] and lower right [Blue/Red] corner of
the PCB.
Take out the five screws (#663).
[Black/Red]
[Red]
#663 #663
#663
Lift the one side of the PCB as below, and disconnect the connector of the back.
Remove the TOGO PCB unit (#B2001).
#B2001
Turn up
- D19 D5000 -
INC
VBA24001-R.3783.A
Removal of top cover
Remove the solders of the wires [Green/Gray/Blue/Orange] from the SB PCB unit (#B2006).
Remove the solder of the wire [Black] from the DC/DC PCB (#B2002).
[Green/Gray/Blue/Orange]
[Black]
#B2002
#607
#638
#737 2
#B271
Lowering this lever will facilitate
the removal of [#B271].
- D20 D5000 -
INC
VBA24001-R.3783.A
SB upper cover
Push the SB lock lever in the direction of the arrow, and raise (pop-up) the built-in SB (flash unit).
SB lock lever
#632
House the SB lower control unit (#B302), and remove the SB upper cover (#301).
#301
- D21 D5000 -
INC
VBA24001-R.3783.A
SB lower control unit
Take out the screw (#650), and release the wires from the bosses.
Unsolder the wires [Red/Blue/Green/Black] of the top cover FPC unit (#B1012).
[Red/Blue/Green/Black]
#B1012
#650
Boss
Boss
- D22 D5000 -
INC
VBA24001-R.3783.A
While pushing the rotate shaft (#306), take out the screw (#733) and remove the spring (#305).
Remove [#306].
Remove the SB rotating collar (#308), while releasing its two hooks.
Remove the SB lower control unit (#B302).
#733
#305
#B302
AU
TO
#306
#308
#311
AU
TO
- D23 D5000 -
INC
VBA24001-R.3783.A
SB release base unit
Remove the solders of the wires [Red/Black] from the top cover FPC unit (#B1012).
Release the wires [Red/Black] from the guides.
Take out the two screws (#609), and remove the SB release base unit (#B2455).
Guide
#B2455
[Red/Black]
#609
#B1012
#327
#608
[uncoated/Black]
#B325
- D24 D5000 -
INC
VBA24001-R.3783.A
Power SW FPC unit
#635
#B1011
Remove the rubber SW (#382), the + - /aperture button (#381) and the info button (#384).
Take out the two screws (#605).
Remove the on-off SW brush (#348), on-off click spring (#347), and on-off dial (#B345).
AU
TO
#B345
#384
#347
#381
#348
#382
#605 2
- D25 D5000 -
INC
VBA24001-R.3783.A
C/D unit
#635
Top cover FPC unit
Remove the five solder bridges.
Unsolder the wire [Black] that is connected to the DC/DC PCB.
Take out the two screws (#635), and remove the top cover FPC unit (#B1012).
[Black]
#635 #B1012
- D26 D5000 -
INC
VBA24001-R.3783.A
Mode dial unit / AF/AE-L button / Delete button / AF-assist lamp window
Take out the screw (#640).
Remove the contact brush (#372), click spring (#373), and mode dial unit (#B371).
Remove the retainer ring (#387), and remove the AF/AE-L button (#386).
Remove the delete button rubber SW (#423), and delete button (#428).
Remove the super X, and detach the AF-assist lamp window (#326).
AU
TO
#B371
#386
#428
#423
#387
#373
#372 #326
Adhesive: Super X
#318
#316
#B317
#322
#654 4
- D27 D5000 -
INC
VBA24001-R.3783.A
5. Image sensor
SZ-DC/DC PCB unit
Disconnect the connection-FPC (#1026) from the [Yellow/Black]
connector.
Unsolder the wires [Yellow/Black].
#B2003
Take out the two screws (#670) and the one ne
screw (#687).
Remove the SZ-DC/DC PCB unit (#B2003).
#1026
#687
#670
#631 #B2051
[Green/Purple]
- D28 D5000 -
INC
VBA24001-R.3783.A
6. Separation of Front body from Rear Body
Bottom base unit
Take out the five screws (#616).
Take out the three screws (#691).
#616
#691
#691
#B66
- D29 D5000 -
INC
VBA24001-R.3783.A
Unsolder the wires [Black/Blue], which are connected from the penta unit.
Unsolder the wires [Black/Red], which are connected from the SQ PCB unit.
[Black/Blue]
[Black/Red]
#624
- D30 D5000 -
INC
VBA24001-R.3783.A
- D31 D5000 -
INC
VBA24001-R.3783.A
7. Rear body
Microphone
Remove the microphone (#1046).
#1046
Main condenser
Unsolder the wires [Red/Black].
Take out the two screws (#615).
Remove the SB condenser unit (#B1048).
Remove the condenser (#1048) and two pieces of the double-stick tape (#141) from the condenser holder.
[Red/Black]
#B1048
#615
Condensor holder
#1048
#141
- D32 D5000 -
INC
VBA24001-R.3783.A
SB PCB unit
#B2006
#687
#B82
Rear body unit
Boss [Red/Black]
#B82
- D33 D5000 -
INC
VBA24001-R.3783.A
DC/DC PCB unit
[Black/Red/Blue]
#665
- D34 D5000 -
INC
VBA24001-R.3783.A
Battery box
#159
#615
#607
#607
#160
#157
#141
#B1044
- D35 D5000 -
INC
VBA24001-R.3783.A
Eyelet unit, etc
#147
#145
#735
#65
#694
#147
#145
#957
#143
#143
TA-0026(6x11)
#694 TA-0026(6x11)
#143
#139
#904
#906
- D36 D5000 -
INC
VBA24001-R.3783.A
8. Front body
Shutter
Remove the sponge (#757).
#757
#635
#149
- D37 D5000 -
INC
VBA24001-R.3783.A
Meterring FPC unit
Take out the screw (#607), and remove the retainer plate (#293).
Disconnect the FPC from the connector.
Take out the three screws (#607), and remove the metering FPC unit 1 (#B11013).
(Caution: Do NOT touch the red-marked screws during disassembly, because they are for adjustments.)
#293
#607
#607
#B11013
#638
#B261
- D38 D5000 -
INC
VBA24001-R.3783.A
Penta unit
#635
#201 #202
- D39 D5000 -
INC
VBA24001-R.3783.A
SI unit
Turn the gear in the direction of the arrow, and lower the mirror.
Take out the two screws (#610), and remove the mirror setting unit (#B120).
#B120
#610
#709
#B2050
- D40 D5000 -
INC
VBA24001-R.3783.A
Take out the two screws (#635).
Remove SI retainer unit (#B277).
#B277
#635
Remove the two SI light guides (#335).
Disconnect the FPC from the connector.
Take out the two screws (#606).
Peel off the tape (#709).
Remove the SI LED FPC unit (#1017).
#335
#709 #606
#1017
- D41 D5000 -
INC
VBA24001-R.3783.A
Relay PCB unit
#670
[Yellow/Black]
With the FPC of the lens contact unit (#B2113) being turned up, take out the screw (#670).
Remove the Relay PCB unit (#1007).
#670
#1007
Boss
- D42 D5000 -
INC
VBA24001-R.3783.A
Removal of bayonet
Take out the five screws (#648) and the one screw (#660).
Remove the bayonet (#111).
Remove the lug plate (#137).
Remove the three bayonet springs (#112).
#137
#648 #112
#660
#607
#642
- D43 D5000 -
INC
VBA24001-R.3783.A
Peel off the synchro-mode/SB pop-up SW area, and turn up the FPC.
Remove the lens contact unit (#B2113).
- D44 D5000 -
INC
VBA24001-R.3783.A
SQ base unit
[Orange/Black]
#B242
#638
- D45 D5000 -
INC
VBA24001-R.3783.A
AF sensor unit
Take out the three screws (#162) with hex key ( 1.5mm).
The AF sensor unit (#B2163) and three springs (#161) will come off.
#B2163
#162 3
B2
2
#161 3
#683 2
#276
#B1021
#332 #758
#37
#38
- D46 D5000 -
INC
VBA24001-R.3783.A
plate
#299
#B115
#119
#B116
- D47 D5000 -
INC
VBA24001-R.3783.A
F-min SW section
#607
#135 #645
#134
#131 Orange:SQ FPC
#136
Black:SQ FPC
#133
#236
- D48 D5000 -
INC
VBA24001-R.3783.A
Remove each part/component.
#B2231
#240
#238
#239
#199 2
#236
#190
#205
#191
#206
#643
#203
- D49 D5000 -
INC
VBA24001-R.3783.A
Assembly/Adjustment Caution: For the tapes or sponges which are not described in
"Assembly" section, refer to the repair parts list.
1. Front body
Mirror unit
#B2231
#240
#239
Be careful NOT to bend this.
#238
#199 2
#236
With the mirror being raised, insert the pins and apply the adhesive (Super X) to each pin.
#236
- A1 D5000 -
INC
VBA24001-R.3783.A
Aperture lever section
#190
#205 #191
#206
#643
#203
Grease:LEN317A
#206
Grease:LEN317A
#205
- A2 D5000 -
INC
VBA24001-R.3783.A
F-min SW section
#607
#645
#135
#134
Orange:SQ FPC
#136 #131
Black:SQ FPC
#133
Grease:LEN317A
#B115
#119
#B116
Boss hole
- A3 D5000 -
INC
VBA24001-R.3783.A
plate
#299
#B1021
#332 #758
[#276/#332] attaching
[#276 and #332] position
attaching position [#758] attaching position
#38 #37
Attaching position
#758
[#332] must be attached to the mold.
- A4 D5000 -
INC
VBA24001-R.3783.A
AF sensor unit
Attach the three springs (#161).
Place the AF sensor unit (#B2163)
Turn the three screws (#162) lightly all the way with hex key ( 1.5mm), and then give each 1.5-turn
counterclockwise.
#B2163
#162 3
B2
2
#161 3
SQ PCB unit
Move the aperture lever of the SQ PCB unit (#B242) in the direction of the arrow, and check that it is
movable freely.
If not, turn the red-indicated gear in "Fig. 1" in the direction of the arrow, and make it movable.
Move the (red-circled) roller section all the way to the end.
#B242
Roller section
- A5 D5000 -
INC
VBA24001-R.3783.A
Operate the mirror-up lever (#203), which is assembled in [#B22RP] in the direction of the arrow, and set
to be "mirror-down" as below.
While inserting the head of the aperture lever of the SQ PCB unit (#B242) into the gap of [#B22RP], mount
by fitting with the boss.
#B22RP
#203
#B242
[Orange/Black]
#638
Pass through
behind FPC
- A6 D5000 -
INC
VBA24001-R.3783.A
Lens contact unit
While turning up the FPC, mount the lens contact unit (#B2113).
#B2113
Boss
#642
- A7 D5000 -
INC
VBA24001-R.3783.A
#607
Mounting of bayonet
Mount the lug plate (#137).
Attach the three bayonet springs (#112).
Mount the bayonet mount (#111).
Tighten the five screws (#648) and the one screw (#660) in the below numeric order from to .
#137
#112 #648
#660
Grease:LEN317A
Grease:LEN317A
- A8 D5000 -
INC
VBA24001-R.3783.A
Height adjustment of Aperture lever
Measure the height of the aperture lever with the tool (J18004).
Standard: 3.3 - 3.6mm
In case the result does not meet the standard, bend the aperture
lever section for adjustment.
Be careful NOT to bend the inside of the lever.
Aperture lever
- A9 D5000 -
INC
VBA24001-R.3783.A
Relay-PCB unit
With the FPC of the lens contact unit (#B2113) being turned up, mount the relay-PCB (#1007) by fitting
with the bosses.
Tighten the screw (#670).
Boss
#670
#1007
Boss
(#1030 back)
[#905/#750] attaching position
#670
[Yellow/Black] #905
#750
- A10 D5000 -
INC
VBA24001-R.3783.A
SI unit
Mount the SI LED FPC unit (#1017).
Attach the tape (#709).
Tighten the two screws (#606).
Connect the FPC to the connector.
Mount the two SI light guides (#335). #1017
#335
#709 #606
- A11 D5000 -
INC
VBA24001-R.3783.A
Attachment position for Finder field frame
Attach the tape (#295) to the SI retainer unit (#B277).
Attach the two sponges (#793) to the finder field frame 2 (#283), and then mount on the SI retainer unit
(#B277).
#295
#B277
Boss
#283
#793
#B277
#635
- A12 D5000 -
INC
VBA24001-R.3783.A
Pass the FPC of the SI unit (#B2050) through -framed area of the retainer plate (#339), and mount it.
Engage the hook.
#B2050 #339
-framed area
Connect the FPC to the connector, and attach the tape (#709).
#709
Mount the mirror setting unit (#B120), and tighten the two screws (#610).
#B120
#610
- A13 D5000 -
INC
VBA24001-R.3783.A
Penta unit
#B4
#635
#201 #202
- A14 D5000 -
INC
VBA24001-R.3783.A
Mount the eyepiece barrel unit (#B261) by fitting with the boss, and tighten the two screws (#638).
#638
Mount the AE FPC unit (#B11013) by fitting with the boss, and tighten the three screws (#607).
Connect the FPC to the connector.
Mount the plate (#293) by fitting with the boss, and tighten the screw (#607).
(Caution: Do NOT touch the red-marked screws during assembly, because they are for adjustments.)
#607
#B11013
#293
#607
- A15 D5000 -
INC
VBA24001-R.3783.A
! WARNING
NEVER look directly at the laser beam which is reflected
by the mirror of cameras/inspection tools.
Position of operator and where the laser beam must not be looked directly.
Operator
Chart area
Chart
- A16 D5000 -
INC
VBA24001-R.3783.A
49
Tilted mirror
Reference Line
Remove the finder screen. Replace it with the D5000.45 deg. angle main-mirror tool (J15436).
Camera: D300
- A17 D5000 -
INC
VBA24001-R.3783.A
Check whether the results meet the standard. If not, make the adjustment.
Standard value
Main mirror
Left-right deviation 0 2
Up-down deviation 4
Device
Press the lock/release button to detach the body from the mount-face.
- A18 D5000 -
INC
VBA24001-R.3783.A
2. Positioning of Sub-mirror
The sub-mirror angle of this model is 51 degree angle. However, because the mirror tool for this angle is
not set as RP, regard the position which is 105.2 mm lower than the 54 degree-angle index position as the
51 degree-angle one, and make a necessary check.
70mm
3mm
3mm
59
Tilted mirror
49
Tilted mirror
230mm
47.75
105.2 Tilted mirror
Tilted mirror
51
45
Flat mirror
Regard this index position as a reference,
and make a measurement.
Reference Line
Set the 54-angle measurement-use mirror, which is prepared as single part (J19132D), by placing it
horizontally, as if sandwiched in between the two adjustment boards.
Slide the height display (of the measurement-use mirror) forward, and turn the screw to secure it.
Screw
Slide forward.
Sandwich in
Measurement-use mirror
Standard position
Rough indication: Height of
measurement-use mirror of D5000
Screw
J19132H
MAIN/SUB MIRROR ANGLE INSPECTION TOOL-USE CHART
Camera release guard
Radiate the laser beam. Confirm that the laser reflected image is positioned at the scale of the set angle.
If the reflected image is out of alignment, adjust it by turning the adjustable screw X (horizontally) or Y
(vertically) with the laser beam being radiated.
59 Adjustable screw: X
Tilted mirror
54 Adjustable screw: Y
Tilted mirror
47.75
Flat mirror
49
Tilted mirror
Tilted mirror
51
45
Flat mirror
Camera-release guard
Standard position
- A21 D5000 -
Reference Line
INC
VBA24001-R.3783.A
Angle measurement of Sub-mirror
Attach the camera body to the mount-face, and operate the mirror a few times.
Position the camera in the direction of the arrow.
J19132H
MAIN/SUB MIRROR ANGLE INSPECTION TOOL-USE CHART
Camera: D300
With the mirror being raised, move the (measurement-use) mirror stage to the stop position.
Confirm that the camera-release guard is kept raised horizontally at the stop position, then lower the mirror.
59
Tilted mirror
54
Tilted mirror
47.75
Flat mirror
49
Camera-release guard Tilted mirror
Turn the (mirror height) adjusting micrometer and get the position where the laser reflected image does not
move. At this position, check the angle of the sub-mirror.(The 51 degree-angle index position is 105.2 mm
47.75
lower than the 54 degree-angle index position.) Tilted mirror
- A22 D5000 -
INC
VBA24001-R.3783.A
Sub-mirror
Measurement-use mirror
Avoid contact
Reference position
- A23 D5000 -
INC
VBA24001-R.3783.A
Check whether the results meet the standard. If not, make the adjustment.
Standard value
Sub mirror
Left-right deviation -
Up-down deviation 0 7
Device
After completing the inspection and adjustment, with the mirror being raised, return the mirror stage to the
standard position.
Confirm that the camera-release guard is kept lowered, and lower the mirror.
Detach the camera body from the mount-face.
- A24 D5000 -
INC
VBA24001-R.3783.A
Shutter
Turn the red gear in the direction of the arrow, and raise the mirror.
Mount the shutter (#31).
Tighten the two screws (#635).
Make the solder bridges.
Attach the sponge (#149).
#31
#635
#149
Attach the sponge (#757) to the gap between the shutter (#31) and the front body unit (#B22RP).
#757 #758
- A25 D5000 -
INC
VBA24001-R.3783.A
2. Rear body
Eyelet unit, etc [#147] attaching position [#147] attaching position
Joint line Joint line
#147
#145
#735
#65
Oil barrier:OS-30MEL Oil barrier:OS-30MEL
#694
#147
#145
#957
#143
#143
TA-0026 (6x11)
#904
#906
Attaching position
Back
- A26 D5000 -
INC
VBA24001-R.3783.A
Battery box
#607
#607 #160
#157 Dipping
Grease: CFD-409Z
#156
Insert the
head into the
hole.
#141
#B1044
- A27 D5000 -
INC
VBA24001-R.3783.A
#159
#615
- A28 D5000 -
INC
VBA24001-R.3783.A
DC/DC PCB unit
Mount the DC/DC PCB unit (#B2002) and tighten the two screws (#665).
Connect the FPC.
Solder the battery-contact wires [Black/Red/Blue].
[Black/Red/Blue]
#665
#B2002
- A29 D5000 -
INC
VBA24001-R.3783.A
SB PCB unit
Mount the SB PCB shield plate unit (#B82).
Put the SB PCB unit (#B2006) in between [#B82] and the rear body unit. (Put the wires inside the shield.)
Tighten the screw (#687).
Attach the connection-FPC (#1029) by fitting with the boss.
Arrange the wires [Red/Black], which are connected from the DC/DC PCB unit (#B2002), as below, and
solder them.
#B82
#B2006
#B82
Rear body unit
#B2002
#687
Boss
[Red/Black]
#1029
- A30 D5000 -
INC
VBA24001-R.3783.A
Main condenser
Attach the two pieces of the double-stick tape (#141) to the condenser holder, and adhere the condenser.
Mount the SB condenser unit (#B1048) by fitting with the boss.
Tighten the two screws (#615).
Solder the wires [Red/Black], which are connected from the SB PCB unit (#B2006).
Condenser holder
#1048
#141
#B1048
[Red/Black]
#615
Microphone
Attach the microphone (#1046).
#1046
- A31 D5000 -
INC
VBA24001-R.3783.A
3. Assembly of front body into rear body
Put mirror down, and assemble the front body into the rear body being careful of wires and FPCs).
#624
- A32 D5000 -
INC
VBA24001-R.3783.A
Bottom base unit
Mount the bottom base unit (#B66) (being careful NEITHER to be caught by the PCB NOR to pinch the
wires as below).
Tighten the five screws (#616) and three screws (#691) in the numeric order from to .
#B66
#616
#691
#691
- A33 D5000 -
INC
VBA24001-R.3783.A
Inspection and Adjustment of Body back
J18001-1
(1) Mount the tool (J18001-1) on the surface plate as above, then set the dial gauge to "0".
(2) From "0" position of (1), turn the index circle in the direction of the arrow so that the needle is on 12 (0.12mm)
position.
(3) Measure the body back based on "0" position of the index circle.
0 0.015 mm Revision
If the value is "00.05 mm / Parallelism: 0.015mm or less", it is within standard.
e.g.
0.00 mm 2.12 mm
ZERO/ABS ON/OFF ZERO/ABS ON/OFF
J18001-1
Surface
plate Surface
plate
(1) Mount the tool (J18001-1) on the surface plate as above, then turn the digital gauge ON and press [ZERO/
ABS] button so that the value becomes "0".
(2) Measure the body back based on "0" position
(3)
Subtract "
2.12mm
" from the measured value. If the value is "00.05 mm / Parallelism: 0.015mm or less",
0 0.015 mm Revision
it is within standard.
"2.12mm" is a difference, resulting from subtracting [the height (46.67mm) of the body back tool
(J18001-1)] from [D5000 standard value (48.79mm)].
Changed page 3 - A34 D5000 - June. 22. 2009
INC
VBA24001-R.3783.A
Measure six places from the bayonet face to the image PCB attaching face.
Measure the six places from the bayonet face to the image
PCB attaching face.
mark: to be measured
Standard: 48.790.05mm / Parallelism: 0.015mm or less
48.79 0.015mm Revision
Note: For some bodies, the washer(s) is/are already put on the attaching face of the image sensor, or
already the lumirror sheet attached on the side. The details are as follows:
Mark indication
Location
Marking Marking
Attaching position
- A36 D5000 -
INC
VBA24001-R.3783.A
Solder the wire [Black] which is connected from the ground.
Solder the wire [Blue] which is connected from the lens contact.
Solder the wires [Black/Red] which are connected from the SQ PCB unit.
[Black]
[Blue]
[Black/Red]
- A37 D5000 -
INC
VBA24001-R.3783.A
4. Image sensor
Sponge
Mount the image sensor unit (#B2051), and tighten the three screws (#631).
Solder the wires [Green/Purple].
Caution: Some bodies have already the washer put on the surface where the image sensor unit is mounted
or already the lumirror sheet attached on the side.
In the latter case (lumirror sheet attached), remove the super X, which is applied to the side (see below
" " area), and then remove the image sensor unit.
#631 #B2051
[Green/Purple]
- A38 D5000 -
INC
VBA24001-R.3783.A
SZ-DC/DC PCB unit
Mount the SZ-DC/DC PCB unit (#B2003), and tighten [Yellow/Black]
the two screws (#670) and the one screw (#687).
Connect the connection-FPC (#1026) to the connector.
#B2003
Solder the wires [Yellow/Black].
#1026
#687
#670
- A39 D5000 -
INC
VBA24001-R.3783.A
5. Top cover
Hot shoe
Attach the backing plate (#322), shoe spring (#318), hot shoe (#316), and hot shoe mold unit (#B317).
Tighten the four screws (#654) in the numeric order from to .
#318
#316
#B317
#322
#654 4
Mount the AF-assist lamp window (#326), and apply the super X.
Attach the AF/AE-L button (#386) and secure it with the retainer ring (#387).
#326
#387
Adhesive: Super X
- A40 D5000 -
INC
VBA24001-R.3783.A
Mode dial unit & Delete-button-rubber SW
Attach the mode dial unit (#B371), click spring (#373), and contact brush (#372).
Tighten the screw (#640).
Attach the delete button (#428) and delete-button-rubber SW (#423).
#428
#423
#373
#372
#640 Grease: LEN317A
Top cover FPC unit
Mount the top cover FPC unit (#B1012) by fitting with the bosses.
#B1012
Boss
- A41 D5000 -
INC
VBA24001-R.3783.A
Solder the wire [Black], which is connected to DC/DC PCB, and arrange the wire in the groove.
Tighten the two screws (#635) in the numeric order from to . (When mounting [#B1012], fit in the
AF/AE-L button firmly.)
Make the five solder bridges.
[Black]
Grease: PL-22SEL
#635
OK
NG: Not Good
C/D unit
Mount the C/D unit (#B367) in the direction for positioning.
Tighten the two screws (#635) in the numeric order from to .
Make the three solder bridges.
#B367
#635
- A42 D5000 -
INC
VBA24001-R.3783.A
Release button unit / each button, etc
Mount the on-off dial (#B345) set to ON position, and attach the on-off click spring (#347), and on-off
SW brush (#348).
Tighten the two screws (#605).
Mount the info button (#384), the + -/aperture button (#381), and the ribber SW (#382).
AU AU
TO
TO
#B345
#384
#347 Back Grease: LEN317A
#381
#348
#382
#605 2
Mount the power SW FPC unit (#B1011) by fitting with the bosses.
Tighten the three screws (#635) in the numeric order from to .
Connect the FPC.
#B1011
Grease: PL-22SEL
#635
- A43 D5000 -
INC
VBA24001-R.3783.A
AF-assist lamp unit
Mount the -assist lamp unit (#B325) by fitting with the boss, and tighten the screw (#608).
Solder the wire [Black/uncoated].
Attach the flocked sheet (#327), which is for dust-proof.
#327
Attaching position
Boss position
#608
[Black/uncoated]
#B325
SB release base unit
Mount the SB release base unit (#B2455) by fitting with the boss.
Tighten the two screws (#609) in the numeric order from to .
Arrange the wires [Red/Black] along the guide, and solder them on the top cover FPC unit (#B1012).
Guide
#B2455
[Red/Black]
#609
- A44 D5000 -
INC
VBA24001-R.3783.A
SB lower control unit
Attach the two rubbers (#311) by aligning each position.
#311
AU
TO
Mount the SB lower case unit (#B302), while holding and the both sides and pulling outward as below.
Grease: CFD-409Z
Grease: CFD-409Z
Grease: CFD-409Z
Grease: CFD-409Z
#B302
- A45 D5000 -
INC
VBA24001-R.3783.A
Attach the SB rotating collar (#308), and engage the hooks.
Attach the SB case rotate shaft (#306). While holding it, tighten the screw (#733).
Attach [#306] by
holding it.
AU
TO
Dipping
Grease: CFD-409Z
#306
#308
Attach the spring (#305) by aligning with the groove, and engage the hook.
#305
- A46 D5000 -
INC
VBA24001-R.3783.A
Insert the eight wires as below, beginning with the thick one.
[Red/Blue/Green/Black]
#650
- A47 D5000 -
INC
VBA24001-R.3783.A
SB upper cover
House the SB lower control unit (#B302), and mount the SB upper cover (#301).
#301
Push the SB lock lever in the direction of the arrow, and raise (pop-up) the SB unit.
#632
- A48 D5000 -
INC
VBA24001-R.3783.A
Top cover
When the AE-CCD positioning adjustment is made, solder only the four wires, which are connected from the top cover, on the SB PCB. Without
assembling the eyepiece mold unit (#B271), make a temporary assembly of the top cover, and proceed with the assembly up to Page A51.
Mount the eyepiece mold unit (#B271). (After this mounting, raise the diopter adjustment lever to secure
[#B271] firmly.)
Mount the top cover.
Tighten the screw (#638).
Tighten the screw (#607).
Tighten the two screws (#737).
#B271
#607
#737
#638
[Green/Gray/Blue/Orange]
[Black]
- A49 D5000 -
INC
VBA24001-R.3783.A
TOGO PCB unit
Turn up the TOGO PCB unit (#B2001), and connect the harness to the connector on the back of [#B2001].
Mount [#B2001] by fitting with the bosses.
#B2001
Tighten the five screws (#663).
Solder the wires [Black/Red] and wires [Blue/Red].
Connect the seven FPCs and the harness to the connectors.
[Black/Red]
[Red]
#663
#663
#663
- A50 D5000 -
INC
VBA24001-R.3783.A
Inspection and adjustment of AE CCD positioning
! WARNING
There are high voltege parts inside. Be careful of this electric shock,
when you remove the cover.
Under the environment where the AE-CCD positioning is adjusted, use the reference body and confirm
results.
In case the measured value is out of standard, check whether there is no deviation of the focus area
positioning.
In case the measured value is out of standard, change the environment of measurements. (e.g. setting place/
direction, room brightness, etc)
Procedure
Solder only the four wires, which are connected from the top cover, on the SB PCB. Make a temporary
assembly of the top cover and bottom cover.
Mount "AF50/1.4D" on the camera, and fix them on the tripod horizontally.
Connect the camera and PC via USB cable (UC-E6).
Supply power via the AC adapter (EH-5a) and power connector (EP-5).
Be careful NOT to cause a short-circuit at uncovered portions.
Attach the AE-CCD positioning tool (J63108) in the color viewer (J63070), and turn power ON.
Keep the 0.7-m distance between the front face of the AE-CCD positioning tool and the reference surface of
the camera. Rotate the focus ring to set to "0.7 m".
Start up the inspection and adjustment software for D5000 (J65135), and select "Inspection and Adjustment
for AE CCD POSITION" then "Set Camera for AE CCD POSITION", in order to indicate the focus areas.
Looking through the viewfinder, move the camera so that the focus areas coincide with the holes of the AE-
CCD positioning tool as below.
Set the camera and AE-CCD positioning tool horizontally.
Select "Inspection and Adjustment for AE CCD POSITION".
Cover the camera with a black cloth, etc, when measured.
Turn the three adjustment screws all the way lightly, and then give each 2.5 turns counterclockwise. Follow
the instructions on PC and adjust the position of the AE-CCD.
After completing the adjustment, secure the three adjustment screws with screw lock.
AE-CCD positioning
Attaching surface of the
tool (J63108
imaging-PCB
AF 50/1.4D
Approx 0.7 m
- A51 D5000 -
INC
VBA24001-R.3783.A
Reference screw
X direction
Loosen
Y direction Y
Y direction
Tighten Adjustment
screw Do NOT apply to the screw
hole.
Remove the bottom cover. From the both terminals of the main condenser, discharge electricity.
2K /5W
- A52 D5000 -
INC
VBA24001-R.3783.A
6. Front cover
Take out the four screws (#610) and the one screw (#626).
Remove the front cover unit (#B24).
#610
#610
#466
#626 #B24
#465
In case this adjustment result is out of standard, raise the SB section and make adjustments by turning
the adjustment dial with hex key.
Standard: 0.1-0.4mm
Adjustment dial
- A53 D5000 -
INC
VBA24001-R.3783.A
7. Back cover
TFT monitor unit
Attach the two sponges (#404) and two sponges (#405) by aligning with the groove of the TFT bottom
cover (#435), in the numeric order from to .
Correcting
sponge
#1049
- A54 D5000 -
INC
VBA24001-R.3783.A
While passing the FPC through, mount the plate (#406).
Connect the FPC.
#406
Pass the harness (#1058) through the hole of the hinge unit (#B454).
#1058
#B454
- A55 D5000 -
INC
VBA24001-R.3783.A
Mount the hinge unit (#B454) by aligning with the groove.
Connect the harness to the connector.
Solder the wires [Orange/Blue/Black/Red].
Arrange the wires as below.
[Orange/Blue/Black/Red]
#B454
- A56 D5000 -
INC
VBA24001-R.3783.A
Mount the hinge bottom cover (#438) by tting with the bosses.
(Caution: If [#438] has scratches/dents, etc, use a new one.
Tighten the screw (#677).
#438
#677
Arrange along the wall. Put the wires [Red/Black] in the slit.
Marking
- A57 D5000 -
INC
VBA24001-R.3783.A
Attach the lock plate spring (#432) by fitting in the grooves.
Attach the lock knob (#431) by fitting in the groove.
#432
#431
#434
- A58 D5000 -
INC
VBA24001-R.3783.A
Position the hinge unit (#B454) as below, and tighten the two screws (#673) and two screws (#674) in the
numeric order from to .
#673
#B454
#674
Mount the hinge top cover (#437), and tighten the screw (#671).
(Caution: If there are scratches/dents, etc, use a new one.
#671
#437
- A59 D5000 -
INC
VBA24001-R.3783.A
#402
#403 #490
#494
- A60 D5000 -
INC
VBA24001-R.3783.A
Back cover
Attach the double-stick tapes (#470 and #476).
Attach the rear rubber (#469).
Attach the two rubbers (#473).
#473
#469
#470
#476
Mount the SD access lamp window (#408), and apply the superglue .
Attach the tape (#706) as below.
Attach the tape (#477) to the boss area.
#706
#477
#408
Adhesive: Superglue
- A61 D5000 -
INC
VBA24001-R.3783.A
Sponge/button/FPC/Speaker
Oil barrier:OS-30MEL
#478
Oil barrier:OS-30MEL
#424
#425
#426
#421
#427
#471
#472 #422
#475
#474
#1047
#683
#412
#418
#419
#B1019
#413
#683
#707
#415
#729
#707
- A62 D5000 -
INC
VBA24001-R.3783.A
Insert the harness of the TFT monitor unit into the hole of the back cover, and attach the hinge sections by
fitting with the bosses. (Inserting the harness side first will facilitate the assembly of the hinge section.
Tighten the two screws (#682).
#682
Hinge section
Hinge section
Boss
Boss
Boss Boss
- A63 D5000 -
INC
VBA24001-R.3783.A
Mount the hinge rear cover A (#445) and hinge rear cover B (#446).
Tighten the two screws (#741).
#741
#446 #445
#705
- A64 D5000 -
INC
VBA24001-R.3783.A
SD cover
Plate
#443
Shaft
Screw
Boss
- A65 D5000 -
INC
VBA24001-R.3783.A
SD cover unit
#448
While inserting the tip of the spring of the SD cover unit (#B443) into the round hole of the back cover
(#401), mount [#B443] by fitting with the bosses.
Tighten the two screws (#684).
#684
#B443
Boss
- A66 D5000 -
INC
VBA24001-R.3783.A
#71
Connect the FPC and harness of the back cover to the connectors of the TOGO PCB (#2001).
Put the grip-side first, and then mount the whole back cover.
- A67 D5000 -
INC
VBA24001-R.3783.A
8. External appearance
Tighten the two screws (#740), two screws (#697), two screws (#690), and two screws (#618) in the
numeric order. #740
#697 #690
#618
- A68 D5000 -
INC
VBA24001-R.3783.A
Accuracy inspection and adjustment (Camera body excl. imaging) NEW TOOL
EP-5
As long as the above hardware requirements are met, any PC such as desktop or laptop, etc is available.
File
D5000.exe Application execution file
NkdPTP.dll Library file: USB communication application extension file for Windows XP
NkdPTPDi.dll Library file: USB communication application extension file for Windows 2000
PTPControl Driver file storing folder for PTP: for Windows 2000
D5000IA.ini File for storing setting conditions of adjustment software
- A70 D5000 -
INC
VBA24001-R.3783.A
Procedure for installation
Because this is the self-extracting file, decompress the file before installing, and follow the next procedure.
1. Create a folder for installation under any drive and name. C: DeskTopLauncher\D-SLR\D5000
- A71 D5000 -
INC
VBA24001-R.3783.A
4. When the decompression of file is finished, the file (D5000.exe) is created.
Start-up of Program
1. When "D5000 EXE" is started, the following window will appear. So type in the user key.
(ref. TIE07023-1)
Caution:
Once the user key is typed, from the next time, the adjustment screen will appear from the beginning.
- A72 D5000 -
INC
VBA24001-R.3783.A
3 Click "OK". Program will start.
4. To display in Japanese, select the radio button of "Japanese" in "Language" at the lower right corner of the
screen. However, the screen will not be displayed correctly by English OS.
5 To end the program, click "Close ( " button at the top right hand corner of the screen or click "Quit".
When the camera body (excluding imaging) is inspected and adjusted, the USB connection will be reset in
the process of writing the data into the camera. Therefore, the following message will appear but does not
affect the adjustment. Click "Cancel", and proceed with the next.
D5000
- A73 D5000 -
INC
VBA24001-R.3783.A
Procedure for installing USB driver
If this program is used by the USB interface, installing the USB driver is necessary.
But if the OS is "Windows XP", the driver is already preloaded so it is not necessary to install it.
(3) Select "Search for a better drive than the one your device is using now. (Recommended)", and click "Next".
(4) Click "Reference" of "Specify a location" and select the directory where the driver was copied, such as
"C: D5000PTP". Then click "Next".
C:\D5000\PTPC
- A74 D5000 -
INC
VBA24001-R.3783.A
(5) Confirm that the driver is located at the right place, and click "Next".
C:\D5000\PTPC\NKCTLPTP.INF
- A75 D5000 -
INC
VBA24001-R.3783.A
Necessary adjustments when parts are replaced
1
SZ-DC/DC PCB
unit
1. When only TOGO PCB unit is replaced, be sure to update the MAIN&RISC firmware before writing the fixed
values.
- A76 D5000 -
INC
VBA24001-R.3783.A
Firmware update
A Main
B Risc
L L Lens version(This is used for
"Distortion control of image
editing function of D5000.")
Press the OK button of the camera and turn the camera off.
- A77 D5000 -
INC
VBA24001-R.3783.A
2. Update MAIN firmware
Insert the SD card containing the firmware (D5000_Axxxxxx.BIN) into the camera.
Turn the camera on.
Press the MENU button and select "Firmware version" in the setup menu.
The current firmware version will be displayed. Highlight "Update" and press the multi-selector to right.
The firmware update screen will be displayed. Highlight "Yes" and press the OK button of the camera to
begin the update.
- A78 D5000 -
INC
VBA24001-R.3783.A
- A79 D5000 -
INC
VBA24001-R.3783.A
3. Update RISC firmware
Insert the SD card containing the firmware (D5000_Bxxxx.bin) into the camera.
Turn the camera on.
Press the "MENU" button and select "Firmware version" in the setup menu.
The current firmware version will be displayed. Highlight "Update" and press the multi-selector to right.
The firmware update screen will be displayed. Highlight "Yes" and press the OK button of the camera to
begin the update.
- A80 D5000 -
INC
VBA24001-R.3783.A
- A81 D5000 -
INC
VBA24001-R.3783.A
4. Update both MAIN and RISC firmware versions simultaneously.
Insert the SD card containing the firmware (D5000_Axxxxxx_Bxxxx.bin) into the camera.
Turn the camera on.
Press the "MENU" button and select "Firmware version" in the setup menu.
The current firmware version will be displayed. Highlight "Update" and press the multi-selector to right.
All deletion
L
The firmware update screen will be displayed. Highlight "Yes" and press the OK button of the camera to
begin the update.
All deletion
AE-CCD positioning inspection/adjustment (For device and details, refer to Page A51.USB communi-
Device J18267
J19123
J19123 J18267
- A84 D5000 -
INC
VBA24001-R.3783.A
Aperture accuracy inspectionUSB communication
Caution: Whenever the SQ PCB is replaced, or the TOGO PCB is replaced, make this adjustment.
Device
J19123 J18267
EP-5
Cut out the power connection section of EP-5 and use it.
- A85 D5000 -
INC
VBA24001-R.3783.A
AF inspection and adjustment
Caution: When this adjustment software is used for the first time, prepare three D5000 cameras, and measure by
"Writing of AF adj. lens offset value" on the main menu.
Device
J19123 J18230
- A86 D5000 -
INC
VBA24001-R.3783.A
LARK adjustment (incl. CCD output adjustment) USB communication Adjustment time:approx.20sec .
Device
AF ADJUSTING TOOL Z ADJUSTMENT LENS (FOR 1m) ILLUMINATION BOX FOR AF ADJUSTMENT
J15407
Device
- A87 D5000 -
INC
VBA24001-R.3783.A
FLASH ROM
EEPROM system area
system area High frequency of rewriting
(Low frequency of data)
rewriting data)
Just writing the back-up data into camera does not mean the completion of adjustments.
- A88 D5000 -
INC
VBA24001-R.3783.A
- A89 D5000 -
INC
VBA24001-R.3783.A
Bottom cover
Mount the bottom cover (#25).
Open the power cable cover (#72), and tighten the four screws (#735) and five screws (#671) in the
numeric order.
Tilt the battery cover unit (#B151) at approx. 35 angle, and mount it at the angle.
Grease:MZ-800SEL #671
#25
#735
#72
#735
#B151
Approx.35
- A90 D5000 -
INC
VBA24001-R.3783.A
Shooting-image Adjustment
1. Summary
When the D5000 shooting image-related and listed parts on Page A92 are replaced, be sure to make this
adjustment by the shooting image adjustment software for D5000 (J65136).
Use the D90 reference body beforehand, and get the reference value. Getting reference value will create the
reference data "D5000BSD.DAT" automatically.
Make all of the adjustment items in numeric order. They are programmed to perform continuously, so when one
item is completed, the software automatically moves on to the next item.
If the adjustment is interrupted by "NG", the adjustment item can be restarted halfway from the "NG" item, and
the adjustment of items which ended with "OK" have been completed.
- A91 D5000 -
INC
VBA24001-R.3783.A
3. Hardware requirements
OS Windows2000, WindowsXP, Windows VISTA
Japanese or English OS
PC CPUPentium or more
Memory256MB or more
USB1.1 or 2.0
Screen size: 1024768 pixels or more
4. How to set up
Create "C:\DeskTopLauncher\D-SLR\D5000IMGIMG" folder is created in the hard disc of PC, so copy
"PD5000IMG.EXE". This file is an self-extracting file, so decompress it in the created folder.
Be sure to copy the above file in the same directory. Note that the adjustment can not be made except in the
above folder.
DC/DC
PCB unit
Metering
FPC unit
TOGO
PCB unit
2
SZ-DC/
DC PCB
unit
Relay PCB
unit
Image
sensor unit
TFT
monitor
unit
Rating
plate
1. When TOGO-PCB is adjusted, the fixed values are written automatically.
2. When only TOGO PCB unit is replaced, be sure to update the MAIN&RISC firmware before writing the fixed values.
3. In other cases than replacements of the parts, if users point out the problems, perform the image sensor cleaning
operations/inspections.
Gr/Gb compensation adjustment (R/G/B filter) (Line crawl adjustment) Adjustment time:approx. 30 sec.
Device
J63070 J61185 J63085
ND FILTER 4X
FILTER SP3 FILTER SP2
Device
J18191
ND FILTER 8X
- A93 D5000 -
INC
VBA24001-R.3783.A
Sensitivity ratio adjustment (with brightness box) Adjustment time:approx. 40 sec.
Device J61185
J19123
J18191
ND FILTER 8X
Device
BODY CAP
- A94 D5000 -
INC
VBA24001-R.3783.A
TFT adjustment
Flickering, color and luminance of TFT are adjusted.
Whenever the TOGO-PCB or TFT monitor are replaced, be sure to perform "WRITING THE TFT FIXED
VALUE."
Hue adjustment
Usually default value is set and adjustment is not necessary.
If some problem is found with hue by visual check, adjust and correct it by "+/-" button.
Brightness adjustment
Usually default value is set and adjustment is not necessary.
If some problem is found with brightness by visual check, adjust and correct it by "+/-" button.
It is necessary to calculate the reference values in order to prevent the color temperature fluctuation caused by
the shutter tester or color viewer's changes over time from affecting the results of the shooting image adjust-
ment. By using the reference body, calculate the reference values once in about every 3 months, when either of
the fluorescent of the color viewer or tool lens (F5.6) or ND filter (ND8X/ND4X) is replaced.
- A95 D5000 -
INC
VBA24001-R.3783.A
Initial settings (Factory default settings)
This restores factory default settings. Select the language and video mode. Because this setting of RP TOGO-
PCB is blank, be sure to set the initial default setting when the TOGO-PCB is replaced.
Confirm data
Saving/restoring of the system fixed values, image register, TFT register.
The functions of saving/restoring each data is for sending backup data to Service Planning for analysis, if some
problem occurs.
- A96 D5000 -
INC
VBA24001-R.3783.A
Infinity focus inspection & adjustment
Replace the finder screen with the infinity focus check screen (J15435), and use the reference lens (J18010)
and read the value. In case it is out of standard, increase or decrease washers (#344 selected from A to B) for
adjustments. * Supply the power (Battery or AC adapter) for checking.
Caution: When [J15435] is put in to replace the finder screen, put it with the J number seal downword.
J18010
Reference line "0" position of tool lens
Standard: From +0.06 to -0.06mm 1 scale 0.01mm
#344A 1K603-506 Screen washerA0.10mm
#344B 1K603-507 Screen washerB0.20
Device
J19001 J15435 J18010
- A97 D5000 -
INC
VBA24001-R.3783.A
Measurement of Consumption current value
When this camera is used for measuring the consumption current value, connect the power connector (EP-5) and
install wiring as follows for the measurement.
7.8V 0.3
EP-5
Cut out the power connection section of EP-5 and use it.
Inspection standards
Test item Standard Test condition
Main SWOFF 170 A or less ref. above.
NONE of operational buttons are pushed. AF-S DX ED 18-55/3.5-5.6G
Main SWON (Half-release timer OFF) 160 A or less EV12
Main SWON (Half-release timer ON) 180 m A or less
Caution
When the consumption current value is measured, backup battery must be fully charged.
It takes approx 3 days to fully charge the battery.
- A98 D5000 -
INC
VBA24001-R.3783.A
Cleaning between Penta unit and SI-LCD
#6102
Release the claw of the screen box retaining plate, and put the SI unit straight down to the position as
shown in the figure.
Do NOT pull down with force because the FPC is connected.
SI unit
SI-FPC
SI unit
Caution:
When the above cleaning is carried out, After the assembly, inspect the focusing of the viewfinder.
- A99 D5000 -
INC
Operation check of cleaning image sensor VBA24001-R.3783.A
1. Preparation
Device
J61232
AC ADAPTER
3- OUTPUT STABILIZED OSCILLOSCOPE CONNECTOR EP-5
CURRENT DETECTOR POWER SUPPLY
POWER SUPPLY
2. Connection
Oscilloscope
Camera
EC-43
INPUT DC
V/DIV 100mv/div
TIME/DIV 500ms/div
TRIGGER MODE AUTO
TRIGGER SOURCE CH1
TRIGGER TYPE EDGE
TRIGGER LEVEL 0.400V
CH POSITION -4.00div
PROBE 1:1
FILTER (Smooth) ON
FILTER (Bandwidth) FULL
- A100 D5000 -
INC
VBA24001-R.3783.A
SETTING OF OSCILLOSCOPE
SELECT button
1) Turn the power ( ) ON.
2) Press the INITIALIZE ( ) button, then press SELECT button (INITIAL EXEC) to initialize the settings.
3) All the green lamps ("CH1" - "CH4" ) will be turned on. Then, press the buttons ("CH2" - "CH4" ) one
by one to turn them off , so as to light up only the "CH1" green lamp.
Press the following each button. According to the indications appearing on the screen, set appropriately:
4) Press the red-boxed V/DIV ( ) button, then rotate the jog dial ( ) to set it to "20V".
5) Press the TRIGGER LEVEL/SOURCE ( ) button, then press the SELECT button to set "SOURCE" to
"CH1", and rotate the jog dial ( ) to set "LEVEL" to "0.4V".
6) Press the TRIGGER TYPE ( ) button, then press the SELECT button to set it to "EDGE".
7) Rotate the TIME/DIV dial ( ) and set it to "500ms/div".
8) Press the red-boxed INPUT ( ) button, then press the SELECT button to set it to "DC", while to set "probe"
to "1:1".
9) Press the red-boxed V/DIV ( ) button again, then rotate the jog dial ( ) to set it to "100mV"
10) Press the FILTER ( ) button, then press the SELECT button to set "Bandwidth" to "FULL", while set
"Smooth" to "On".
11) Press the POSITION ( ) button, then rotate the jog dial ( ) to set "CH POSITION" to "-4.00div".
- A101 D5000 -
INC
VBA24001-R.3783.A
4. Judgment
Turn the camera ON (without the SD card).
Turn the MENU button.
Select "Cleaning image sensor" on the setup menu, and perform it. (Set "Clean at startup/shutdown" to
OFF.
Press the START/STOP ( ) button of the oscilloscope to immobilize the screen, and check the waveform.
[For make judgements easier, press the POSITION buttons ( or ) of "HORIZONTAL" or "VERTICAL",
then rotate the jog dial ( ) so as to move the waveform to the position where it can be clearly seen.]
Compare the judgment standard of D5000 (ref. the below chart).
In case judgements are difficult just checking the waveform, send the data to service planning.
- A102 D5000 -
INC
VBA24001-R.3783.A
Hinge SW inspection
- A103 D5000 -
INC
VBA24001-R.3783.A
Main/sub mirror angle inspection tool - use chart
J19132H Deletion
MAIN/SUB MIRROR ANGLE INSPECTION TOOL-USE CHART
Caution:
when this PDF is printed out,
set the zoom in/out setting
of the printer to none .
Otherwise, the printed size will be changed.
49
Tilted mirror
119.1
47.75
Reference point Tilted mirror
75.4
Tilted mirror
Reference width=10 51
45
One square10 Flat mirror 41
Reference Line
Wiring
- E1 D5000 -
INC
VBA24001-R.3783.A
Mounting Drawing
- E2 D5000 -
INC
VBA24001-R.3783.A
TOGO
TOGO PCB UNIT
- E3 D5000 -
INC
VBA24001-R.3783.A
DC/DC
DC/DC PCB UNIT
FUSE
1S460-012
Phenomenon when FUSE has blown out.
Camera can NOT be powered by AC adapter.
- E4 D5000 -
INC
VBA24001-R.3783.A
SZ-DC/DC
SZ-DC/DC PCB UNIT
- E5 D5000 -
INC
VBA24001-R.3783.A
- E6 D5000 -
INC
VBA24001-R.3783.A
- E7 D5000 -
INC
VBA24001-R.3783.A
SB
SB PCB UNIT RELAY PCB UNIT
- E8 D5000 -
INC
VBA24001-R.3783.A
SW FPC FPC
POWER SW FPC UNIT TOP COVER FPC UNIT
- E9 D5000 -
INC
VBA24001-R.3783.A
FPC AF
METERING FPC UNIT AF SENSOR UNIT
- E10 D5000 -
INC
VBA24001-R.3783.A
SQ SI LED FPC
SQ BASE UNIT SI LED FPC UNIT
- E11 D5000 -
INC
VBA24001-R.3783.A
SW FPC
LENS CONTACT UNIT REAR SW FPC UNIT
- E12 D5000 -
INC
VBA24001-R.3783.A
Inspection standards
Items Judgment standard Remarks
External view
Step Btwn top cover & apron: 0.2 mm or less Visual check
(height difference) Other parts: 0.3 mm or less Digital micrometer
Moving parts: 0.5 mm or less
Gap Btwn Top cover & Apron, I/F cover , back cover : 0.2 mm or less
Visual check
Btwn Bottom cover & Apron, I/F cover : 0.2 mm or less
Thickness gauge
SB case & Top cover; SB case & Apron (when built-in flash unit is
housed) : 0.3 mm or less
Other parts: 0.3 mm or less
Moving parts: 0.5 mm or less
Size / Force
Shutter release button Protrusion: 1.1 0.2 mm Digital micrometer
Halfway pressing force: 0.980.49 N (100 50gf) Tension gauge
Halfway pressing stroke: 0.5 0.25 mm
Releasing force: 2.550.69 N (260 70gf)
Releasing stroke: 0.70.25
Extra stroke after releasing button: 0.6 mm or more
Difference btwn Half-releasing and Full pressing force:
0.5N or more (51 gf/gram-force or more
Aperture lever
3.4 height: 3.4 +0.2/-0.1 mm
3.4 height gauge
Main mirror
45 angle: Up-down 10'
Collimator
Right-left 30'
Main mirror tool
Distortion: 8' or less
Visual check
Clearance for up-mirror in mirror box: None
Feeling in hand
Sub-mirror
51 up-down angle: collimator-measured value: 020'
Sub-mirror tool
Distortion: 8 or less
Infinity focus
100m
Collimator
Focus lens
- R1 D5000 -
INC
VBA24001-R.3783.A
Shutter accuracy
Speed accuracy Speed at more than 1/2000 : 0.55EV Shutter speed tester
"1/2000" sec 0.35 EV
From "(1/2000)" to 30 sec.: 0.25 EV
Shutter curtain speed Both front and rear curtains (up-down 16.4 mm or less):
approx. 3.7 ms
- R2 D5000 -
INC
VBA24001-R.3783.A
Field of viewfinder In height and width: "96%" +3% / -2% a tilt of indication
(frame coverage) line (parallel to the
bottom) from the
Parallax Up-down: 0.5 mm or less bottom line of the
(Difference of center Right-left: 0.5 mm or less
frame.
from the shot image/
.
sensor)
- R3 D5000 -
INC
VBA24001-R.3783.A
Items Judgment standard Remarks
Fully-charged battery
Bulb battery life When special Li-ion is used :2 and half hours or more
Clock
- R4 D5000 -
INC
VBA24001-R.3783.A
- R5 D5000 -
INC
VBA24001-R.3783.A
A : 20.2527.0mm
A': 40.554.0mm (excluding "A"
(The size in height and width is measured by aligning
the center of the monitor.)
- R6 D5000 -
INC
VBA24001-R.3783.A
Tools
NEW TOOL
Tool No. Name of tool Others
J15259
AF ADJUSTING TOOL
J15280
LENS HOLDER
J15264
ILLUMINATION BOX FOR AF ADJUSTMENT OUT OF STOCK
J15407
FOR D300 D3 D700 D3X
MULTI CAM 2000 AF CHART
J15409
FOR D2SERIES, D40
CHART BOARD
J18001-1
BODY BACK FOCUS GAUGE
J18004
Aperture lever positioning gauge
J18010
INFINITY STANDARD LENS 50/1.8 OUT OF STOCK
J18358
1
ND FILTER 4X IT USES BY TWO PIECES.
J18191
1
ND FILTER 8X IT USES BY TWO PIECES.
J18230
FOR F5, F100, F90,
YAW PITCH ADJUSTMENT TOOL F90X,D-SLR
J18266
FOR F5, F100, D-SLR
Z ADJUSTMENT LENS (FOR 1m)
- T1 D5000 -
INC
VBA24001-R.3783.A
NEW TOOL
Tool No. Name of tool Others
J18267
LENS AF50/1.4D
J15436
REFLECTION MIRROR
J15435
INFINITY FOCUS ADJUSTMENT SCREEN
J61223
FOR D-SLR
LIGHTING LOUPE
J19001
COLLIMATOR F=600mm
J19004-1
DIAL INDICATOR AND STAND
J18360
FOR C-DSC (L15,L11 etc)
Standard reector 1.5M 1.5M
J19123
KYORITSU ELECTRIC EF-8000
SHUTTER TESTER EF-1(CE)
USABLE
J19132
FOR D3,ETC
MAIN/SUB MIRROR ANGLE INSPECTION TOOL
J61185
FOR D-SLR
D1 STANDARD LENS
J65135
ADJ. SOFT FOR CAMERA
J65136
ADJ. SOFT FOR CAMERA
- T2 D5000 -
INC
VBA24001-R.3783.A
NEW TOOL
Tool No. Name of tool Others
J61235
D90 TOOL BODY
J63068
LUMINANCE METER BM-3000
J63070
COLOR VIEWER
J63085
FOR D2H,D70,D70s,D50,
FILTER SP1 D200,D80,D40,D40x
J63086
FOR D2H,D70,D70s,D50,
FILTER SP2 D200,D80,D40,D40x
J63087
FOR D2H,D70,D70s,D50,
FILTER SP3 D200,D80,D40,D40x
J63108
AE/CCD USE CHART BOARD FOR D90
-
AC ADAPTER CONNECTOR EP-5 RJ IS NOT AVAILABLE
EYEPIECE CAP RJ IS NOT AVAILABLE
BODY CAP RJ IS NOT AVAILABLE
- T3 D5000 -
INC
VBA24001-R.3783.A
NEW TOOL
Tool No. Name of tool Others
C-8008B
CEMEDAIN 8008(BLACK)
EDB0011
SCREW LOCK 1401C
LEN317A
GREASE LEN317A
OS-30MEL
DRY SURF OS-30MEL (OIL BARRIER) OS-30MF IS AVAILABLE
QUICK DRYING GLUE RJ IS NOT AVAILABLE
PERSONAL COMPUTER RJ IS NOT AVAILABLE
10 5 )
POWER SUPPLY(10V 5A)
RJ IS NOT AVAILABLE
FLASH METER RJ IS NOT AVAILABLE
HEX. KEY WRENCH ( 1.5mm) RJ IS NOT AVAILABLE
LENS AF28/2.8D RJ IS NOT AVAILABLE
AF70-300/4-5.6D or AF-SVR70-300/4.5-5.6
LENS AF70-300/4-5.6D or LENS AF-SVR70-300/4.5-5.6
RJ IS NOT AVAILABLE
LENS AF70-200/4-5.6D or LENS AF-SVR70-200/4-5.6
6
USB CABLE UC-E6 RJ IS NOT AVAILABLE
AC ADAPTER EH-5 RJ IS NOT AVAILABLE
- T4 D5000 -
INC
VBA24001-R.3783.A
NEW TOOL
Tool No. Name of tool Others
OSCILLOSCOPE RJ IS NOT AVAILABLE
3
3-OUTPUT STABILIZED POWER SUPPLY
RJ IS NOT AVAILABLE
J61232
CURRENT DETECTOR FOR D700,ETC
J19132D
54
MEASUREMENT USE MIRROR 54 SINGLE PART SETTING
J19135H J19132H
A104
PDF
Deletion 59
Tilted mirror 163.6
54
Tilted mirror 150.5
47.75
Flat mirror 137.1
49
Tilted mirror
119.1
MAIN/SUB MIRROR ANGLE INSPECTION TOOL-USE CHART Print out and use the chart of
47.75
Tilted mirror 75.4 Page A104.
Revision
Tilted mirror
10 51
45
1 10
41
Flat mirror
2
Changed page 2 - T5 D5000 - June. 22. 2009
INC
Screw sheet VBA24001-R.3783 .A
PARTS NAME Bottom cover Back cover Back cover Sponge/Button/FPC/Speaker SD cover unit
DISASSEMBLY D2 D4 D6 D7 D8 D10
TYPE OF SCREW #735 #671 #608 #697 #690 #740 #741 #682 #683 #729 #683 #684
QUANTITY 4 5 2 2 2 2 2 2 3 1 4 2
PARTS NAME TFT monitor unit Front cover unit TOGO PCB unit Top cover unit SB upper cover
DISASSEMBLY D13 D15 D18 D19 D20 D21
TYPE OF SCREW #671 #673 #674 #677 #610 #626 #663 #638 #607 #737 #632
QUANTITY 1 2 2 1 4 1 5 1 1 2 2
PARTS NAME SB lower control unit SB release base unit AF-assist lamp unit Power SW FPC unit On-off dial C/D unit Top cover FPC unit Mode dial unit Hot shoe SZ-DC/DC PCB unit
DISASSEMBLY D22 D23 D24 D24 D25 D25 D26 D26 D27 D27 D28
TYPE OF SCREW #650 #733 #609 #608 #635 #605 #635 #635 #640 #654 #670 #687
QUANTITY 1 1 2 1 3 2 2 2 1 4 2 1
ASSEMBLY A47 A46 A44 A44 A43 A43 A42 A42 A41 A40 A39
PARTS NAME Image sensor unit Bottom base unit Front body into Rear body Main condenser SB PCB unit DC/DC PCB unit Battery chamber Eyelet unit,etc
DISASSEMBLY D28 D29 D30 D32 D33 D34 D35 D36
TYPE OF SCREW #631 #616 #691 #624 #615 #687 #665 #615 #607 #607 #735 #694
QUANTITY 3 5 3 4 2 1 2 4 1 3 1 4
ASSEMBLY A38 A33 A32 A31 A30 A29 A28 A27 A26
- S1D5000 -
INC
VBA24001-R.3783 .A
PARTS NAME Shutter Metering FPC unit Eyepiece barrel unit Penta unit SI unit Relay PCB unit Bayonet mount Lens contact unit
DISASSEMBLY D37 D38 D38 D39 D40 D41 D41 D42 D43 D43
TYPE OF SCREW #635 #607 #638 #635 #610 #635 #606 #670 #648 #660 #607 #642
QUANTITY 2 4 2 2 2 2 2 2 5 1 2 2
PARTS NAME SQ base unit AF sensor unit Inside finder LCD unit Lens release button unit F-min SW section Remove each part
DISASSEMBLY D45 D46 D46 D47 D48 D49
TYPE OF SCREW #638 #162 #683 #621 #607 #645 #643
QUANTITY 3 3 2 3 1 1 1
ASSEMBLY A6 A5 A4 A3 A3 A2
PARTS NAME
DISASSEMBLY
TYPE OF SCREW
QUANTITY
ASSEMBLY
PARTS NAME
DISASSEMBLY
TYPE OF SCREW
QUANTITY
ASSEMBLY
- S2D5000 -