Vous êtes sur la page 1sur 33

Departmental of Civil

Engineering

Faculty selection/recruitment

INDEX
1.

Scheme of Examination

2.

Syllabus

3.

Academic Calendar

4.

Time Table

5.

Lecture Plan

6.

List of Experiments

7.

Tutorial Sheets

8.

Assignment Sheets

9.

Unit Test Question Papers

10. Mid Semester Question Papers


11. Mid Semester Result
12. Solution of Mid Semester Question Papers
13. University Question Papers
14. Course Material (Transparencies, PPT, Handouts etc.)
15. Material beyond syllabus

SCHEME

SYLLABUS

Academic
Calendar
Note: Attach photocopy of Calendar

Time Table

Lecture Plan
The format of lecture plan is attached in a separate sheet

List of
Experiment

Tutorial Sheets

SUBJECT NAME & CODE: THEORY OF STRUCTURE-I


SUBJECT CODE: CE-505
SESSION: 2016
UNIT NO.: 1
TUTORIAL SHEET NO.: 1

Q1 Explain the strain energy in linear elastic system


Q2 Explain the principal of virtual work
Q3 Find the defection at the tip of cantilever by using the principle of virtual
work

Q4A Beam AB of span 3m is fixed at both the end and carries a point load of
9KN at C distant 1m from A. The moment of inertia of the portion AC of
the beam is 2I and that of portion CB is I .Calculate the fixed end moment
and reaction by strain energy method
Q5) State the Maxwell reciprocal theorem

SUBJECT NAME & CODE: THEORY OF STRUCTURE-I


SUBJECT CODE : CE-505
SESSION: 2016
UNIT NO.: 2
TUTORIAL SHEET NO.: 2

Q1 Determine EI constant for general loading in three moment theorem


Q2 Derivation of clapeyrons theorem of three moment
Q3 A beam ABCD ,16m long is continuous over three span AB= 6M
,BC=5m,and CD=5m, the support being at the same level. There is a UDL of
20 KN/m over BC .on AB, there is point load of 80kN at 2m from a on CD,
there is a point load of 60KN at 3m from D. calculate the moments and
reactions at the supports
Q4) State Clapeyrons three moment theorem
Q5Analysis the portal frame by moment distribution method ,portal frame
ABCD ,is hinge at A, The end D is fixed and the joint B and C are rigid .the
column CD is subjected to a horizontal loading of 2 KN/m .A concentrated
load of 6KN act on BC at 1m from B and sketch its deflected shape

SUBJECT NAME & CODE: THEORY OF STRUCTURE-I


SUBJECT CODE : CE-505
SESSION: 2016
UNIT NO.: 3
TUTORIAL SHEET NO.: 3

Q1 Define the slope deflection method?


Q2 Define the assumption of side sway
Q3 A cantilever of length l carries a point load at the free end. Calculate the
slope and deflection at the free end.
Q4 Analyse the beam by SDM

Q5 Explain the frame without joint translation

SUBJECT NAME & CODE: THEORY OF STRUCTURE-I


SUBJECT CODE : CE-505
SESSION: 2016
UNIT NO.: 4
TUTORIAL SHEET NO.: 4

Q1a three hinge parabolic arch of 20 meters span and 4 meter central rise
carry a point load of 4Kn at 4 meter horizontally from left hand hinge
calculate the normal thrust and radial shear also calculate positive and
negative maximum beam
Q2 ) What is the function of cable in suspension cable bridges
Q3 Difference between two hinged and three hinged arch.
Q4 Explain the eddys theorem
Q5A light cable 18 meters long is supported at to end at same level the
support are 16 meters apart the cable supported the load of 8,10, and 12, N
dividing the 16 meters distance in 4 equal part fine the shape of the string
and tension in various portion

SUBJECT NAME & CODE: THEORY OF STRUCTURE-I


SUBJECT CODE : CE-505
SESSION: 2016
UNIT NO.: 5
TUTORIAL SHEET NO.: 5

Q1 Define the various loads on the beam.


Q2 Define absolute bending moment in a girder.
Q3 Explain the term I.L.D
Q4 The load system, shown in the figure moves from left to right on a girder
of span 10 m. Find the absolute maximum bending moment for the girder.

Q5) A beam ABC is supported A,B and C and has hinge at D distance 3 m.
AB= 7 meter and BC= 10 meter draw the influence line for O(1.) Reaction
at A,B, and C ( 2.) S.f at point just to the right of B( 3.) BM at the section 1
meter to the right of the B

Assignment

Assignment-2
Branch: CIVIL ENGINEERING
Semester: VTh
Subject: TOS-I

Sub. Code: CE-505

Q. Define the moment distribution method.


Q.2 What is relative stiffness .
Q.3 write the formula for fixe end condition any two
Q.4) what is distribution factor
Q.5 A Continuous beam ABC consists of spans AB &BC of lengths 6m &
8m having moment of inertia I and 2I respectively. The beam carries a
concentrated load of 120KN at the middle of the span AB & a point load of
90KNM at the middle of span BC. Determine the support moments &
reaction at supports by M.D.M. Draw S.F.D and B.M.D

Assignment-1
Branch:
Subject: TOS-I

Semester: VTh
Sub. Code: CE-505

Q.1 State the Maxwell reciprocal theorem


Q.2 Explain Bettis law
Q.3 State Castiglianos first and second theorem
Q.4 Find the defection at the tip of cantilever by using the principle of
virtual work

Q.5 Analysis the portal frame by strain energy method

Assignment-3
Branch:
Subject: TOS-I

Semester: VTh
Sub. Code: CE-505

Q.1) Determine EI constant for general loading in three moment theorem?


Q.2 Define the slope deflection method?
Q.3 Analyse the portal frame by SDM.

Q.4A beam ABCD ,16m long is continuous over three span AB= 6M
,BC=5m,and CD=5m, the support being at the same level. There is a UDL of
20 KN/m over BC .on AB, there is point load of 80kN at 2m from a on CD,
there is a point load of 60KN at 3m from D. calculate the moments and
reactions at the support
Q.5) what is shear displacement

Assignment-4
Branch:
Subject: TOS-I

Semester: VTh
Sub. Code: CE-505

Q.1) Define three hinge arch .


Q.2 define normal thrust and redial shear
Q.3 Explain the eddys theorem
Q.4 A three hinge parabolic arch of 20 meters span and 4 meter central rise
carry a point load of 4Kn at 4 meter horizontally from left hand hinge

calculate the normal thrust and radial shear also calculate positive and
negative maximum beam
Q.5A light cable 18 meters long is supported at to end at same level the
support are 16 meters apart the cable supported the load of 8,10, and 12, N
dividing the 16 meters distance in 4 equal part fine the shape of the string
and tension in various portion

Assignment-5
Branch:
Subject: TOS-I

Semester: VTh
Sub. Code: CE-505

Q.1 Define rolling load and where it should be applicable


Q.2 Define influence line of BM for floor beam.
Q.3 Write the short explanation of Pettit truss

Q.4 A beam ABC is supported A,B and C and has hinge at D distance 3 m.
AB= 7 meter and BC= 10 meter draw the influence line for O(1.) Reaction
at A,B, and C ( 2.) S.f at point just to the right of B( 3.) BM at the section 1
meter to the right of the B
Q.5 For the continuous beam ABC roller at support at A and C and hinge at
B draw the influence line for reaction A,B and C indicate the value of each
and every spend AB=2L and BC=L EI is constant?

UNIT TEST

UNIT TEST-I
Branch:
Semester: VTh
Subject: TOS-I

Sub. Code: CE-505

Max. Marks:

Time allotted:

NOTE: Attempt only four questions.

Q.1 Explain the strain energy in linear elastic system?


Q.2 Explain the principal of virtual work
Q.3 Find the defection at the tip of cantilever by using the principle of
virtual work

Q.4 State Castiglianos first and second theorem


Q.5 Analysis the portal frame by strain energy method

UNIT TEST-II
Branch:
Semester: VTh
Subject: TOS-I

Sub. Code: CE-505

Max. Marks:

Time allotted:

NOTE: Attempt only four questions.

Q.1 Define the sinking and rotational support


Q.2 Define the term STIFFNESS
Q.3 Analyse the frame by moment distribution method

Q.4 Derivation of clapeyrons theorem of three moment


Q.5A beam ABCD ,16m long is continuous over three span AB= 6M
,BC=5m,and CD=5m, the support being at the same level. There is a UDL of
20 KN/m over BC .on AB, there is point load of 80kN at 2m from a on CD,
there is a point load of 60KN at 3m from D. calculate the moments and
reactions at the supports

UNIT TEST-III
Branch:
Semester: VTh
Subject: TOS-I

Sub. Code: CE-505

Max. Marks:

Time allotted:

NOTE: Attempt only four questions.

Q.1 Define the slope deflection method


Q.2 A cantilever of length l carries a point load at the free end. Calculate the
slope and deflection at the free end.

Q.3 Analyse the beam by SDM.

Q.4 Analyse the portal frame by column analogy method

Q.5 Define analogus column .

UNIT TEST-IV
Branch:
Semester: VTh
Subject: TOS-I

Sub. Code: CE-505

Max. Marks:

Time allotted:

NOTE: Attempt only four questions.

Q.1 What is the function of cable in suspension cable bridges


Q.2 Define rib shortening in arches
Q.3 Analyse the three hinge segmental arch and also find the reaction at the
support
and maximum positive and negative bending moment. Draw the
SF and BM.

Q.4 Explain the eddys theorem.


Q.5 Define normal thrust and redial shear

UNIT TEST-V
Branch:
Semester: VTh
Subject: TOS-I

Sub. Code: CE-505

Max. Marks:

Time allotted:

NOTE: Attempt only four questions.

Q.1 Define the various loads on the beam


Q.2 Define absolute bending moment in a girder

Q.3 Find the shear force at section X for the loaded girder by the influence
line

Q.4 The load system, shown in the figure moves from left to right on a
girder of span 10 m. Find the absolute maximum bending moment for
the girder

Q.5 For the continuous beam ABC roller at support at A and C and hinge at
B draw the influence line for reaction A,B and C indicate the value of each
and every spend AB=2L and BC=L EI is constant?

Mid Semester
Test Question
Papers
(MS-I & MS-II)

Mid Semester Result


Enroll. No

Name

Mid Sem-I

Mid Sem-II

Solution of Mid
Semester
Question Papers

University
Question Papers

Course Material
Each Course File must contain
1. Minimum Ten transparencies of each unit
2. PPT photocopies
3. Notes

Material beyond
Syllabus
You can add notes / PPT / Transparencies etc. of material,
which is not in syllabus but very much related to
the syllabus to upgrade / enhance
knowledge of the student.

Vous aimerez peut-être aussi