Académique Documents
Professionnel Documents
Culture Documents
MAINTENANCE MANUAL
ACCELEROMETER - REMOVAL/INSTALLATION
EFFECTIVITY: ALL
1.
General
A.
B.
There are two accelerometers on each engine, one installed on the first bearing house (front
accelerometer - Z1BRG) and another on the fan frame compressor case (rear accelerometer ZFFCC).
C.
This section gives the procedure to deactivate/activate the Number 1 Bearing (front - Z1BRG)
accelerometer.
D.
DESCRIPTION
77-31-03-000-801-A
77-31-03-400-801-A
77-31-03-000-802-A
77-31-03-400-802-A
77-31-03-040-801-A
77-31-03-440-801-A
E.
EFFECTIVITY
ALL
ALL
ALL
ALL
ON ACFT WITH ENGINE FADEC SOFTWARE VERSION
10EV5.40 AND ON
ON ACFT WITH ENGINE FADEC SOFTWARE VERSION
10EV5.40 AND ON
The abbreviations and acronyms used in this section are given in the sequence below:
ABBREVIATION
DESCRIPTION
AC
Alternating Current
CMC
ECP
FADEC
GEAE
LH
Left-Hand
MCDU
MFD
Multi-Function Display
RH
Right-Hand
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
General
Page 1 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
(Continued)
ABBREVIATION
DESCRIPTION
SSPC
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
General
Page 2 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
TASK 77-31-03-000-801-A
EFFECTIVITY: ALL
2.
General
(1)
(2)
(3)
The front accelerometers are in the engine zones 416 and 426.
(4)
There is no access to the front accelerometer when the engine is installed. To remove the
front accelerometer, it is necessary to remove the engine. Refer to AMM MPP 71-00-01/401.
(5)
B.
C.
D.
References
REFERENCE
DESIGNATION
Powerplant - Removal
LOCATION
REFERENCE
416
Engine - LH Powerplant
426
Engine - RH Powerplant
Job Set-Up
WARNING: MAKE SURE THAT THE AIRCRAFT IS IN A SAFE CONDITION BEFORE YOU DO THE
MAINTENANCE PROCEDURES. THIS IS TO PREVENT INJURY TO PERSONS AND/
OR DAMAGE TO THE EQUIPMENT.
SUBTASK 867-005-A
(1)
Do the procedure to make the aircraft safe for maintenance (AMM TASK
20-00-00-910-801-A/200).
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
000-801-A/400
Page 3 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
(2)
Do the procedure to make the aircraft safe for maintenance of the powerplant (AMM
TASK 71-00-00-910-801-A/200).
SUBTASK 010-007-A
(3)
E.
SUBTASK 020-003-A
CAUTION: DO NOT TOUCH THE ELECTRICAL PINS OF THE CONNECTORS. DAMAGE CAN
OCCUR TO THE INTERNAL ESDS COMPONENTS.
(1)
Remove the number 1 bearing accelerometer. Refer to the latest revision of GEAE
CF34-10E Engine Manual (EMM TASK 72-00-22-020-801/300).
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
000-801-A/400
Page 4 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
TASK 77-31-03-400-801-A
EFFECTIVITY: ALL
3.
General
(1)
(2)
(3)
(4)
There is no access to the front accelerometer when the engine is installed. To install the
front accelerometer, it is necessary to remove the engine. Refer to AMM MPP 71-00-01/401.
(5)
B.
C.
D.
References
REFERENCE
DESIGNATION
Powerplant - Installation
LOCATION
REFERENCE
416
Engine - LH Powerplant
426
Engine - RH Powerplant
Job Set-Up
SUBTASK 867-002-A
(1)
E.
Make sure that the aircraft is in the same configuration as it was at the end of the
removal task (AMM TASK 77-31-03-000-801-A/400).
SUBTASK 420-003-A
CAUTION: DO NOT TOUCH THE ELECTRICAL PINS OF THE CONNECTORS. DAMAGE CAN
OCCUR TO THE INTERNAL ESDS COMPONENTS.
(1)
Install the number 1 bearing accelerometer. Refer to the latest revision of GEAE
CF34-10E Engine Manual (EMM TASK 72-00-22-420-801/400).
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
400-801-A/400
Page 5 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
F.
Job Close-Up
SUBTASK 867-006-A
CAUTION: EXAMINE ALL THE WORK AREAS TO MAKE SURE THAT YOU REMOVED
ALL TOOLS AND EQUIPMENT AFTER YOU COMPLETED THE WORK. IF
YOU DO NOT OBEY THIS PROCEDURE, DAMAGE TO THE AIRCRAFT CAN
OCCUR.
(1)
Remove all tools, equipment and unwanted materials from the work area.
SUBTASK 040-002-A
(2)
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
400-801-A/400
Page 6 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
TASK 77-31-03-000-802-A
EFFECTIVITY: ALL
4.
General
(1)
(2)
(3)
The rear accelerometers are in the engine zones 416 and 426.
(4)
This task refers to the EMM TASK 77-00-00-800-821/200 which contains the procedures to
remove, clean, inspect and install the rear accelerometer. Do only the procedures related to
the removal of FFCC differential accelerometer.
(5)
B.
C.
References
REFERENCE
DESIGNATION
LOCATION
REFERENCE
416
Engine - LH Powerplant
426
Engine - RH Powerplant
147AL
199AL
414AR
424AR
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
000-802-A/400
Page 7 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
D.
E.
F.
DESIGNATION
Commercially available
DESIGNATION
LOCATION
BUS
LOCATION TIP
MCDU
PAGE
CB
E1 REVERSER
LICC
DC BUS 1
SSPC
E1 START VLV
SPDA2
DC ESS BUS
SPDA2-M4
1
ENGINE
CB
E2 REVERSER
RICC
DC BUS 2
SSPC
E2 START VLV
SPDA2
DC ESS BUS
SPDA2-M5
2
ENGINE
Job Set-Up
WARNING: MAKE SURE THAT THE AIRCRAFT IS IN A SAFE CONDITION BEFORE YOU DO THE
MAINTENANCE PROCEDURES. THIS IS TO PREVENT INJURY TO PERSONS AND/
OR DAMAGE TO THE EQUIPMENT.
SUBTASK 867-007-A
(1)
Do the procedure to make the aircraft safe for maintenance (AMM TASK
20-00-00-910-801-A/200).
(2)
Do the procedure to make the aircraft safe for maintenance of the powerplant (AMM
TASK 71-00-00-910-801-A/200).
SUBTASK 861-004-A
(3)
Connect the external AC power supply to the aircraft (AMM TASK 24-42-02-860-801A/200).
SUBTASK 860-004-A
(4)
Make sure that the SLAT/FLAP lever is in the zero-degree position and put a DO NOT
OPERATE tag on it.
SUBTASK 866-004-A
(5)
(6)
On the control pedestal, put a DO NOT OPERATE tag on the POWERPLANT control
panel.
SUBTASK 862-008-A
(7)
For the LH engine, on the MCDU (AMM SDS 34-61-00/1), use the sequence in
parentheses to open this SSPC:
(8)
For the RH engine, on the MCDU (AMM SDS 34-61-00/1), use the sequence in
parentheses to open this SSPC:
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
000-802-A/400
Page 8 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
SUBTASK 010-009-A
(9)
(b)
SUBTASK 862-009-A
(10) For the LH engine, open this circuit breaker and put a circuit breaker ring and tag
(inoperative - do not operate) on it:
(11) For the RH engine, open this circuit breaker and put a circuit breaker ring and tag
(inoperative - do not operate) on it:
SUBTASK 010-010-A
(12) Open the thrust reverser (AMM TASK 78-30-01-910-801-A/200):
G.
(a)
(b)
Accelerometer - Removal
SUBTASK 020-005-A
WARNING: BE CAREFUL WHEN YOU DO WORK ON ENGINE PARTS IMMEDIATELY AFTER
THE ENGINE STOPS. ENGINE PARTS CAN BE HOT. DO NOT TOUCH HOT
ENGINE PARTS WITHOUT GLOVES BECAUSE THESE PARTS CAN CAUSE
INJURY.
CAUTION: DO NOT TOUCH THE ELECTRICAL PINS OF THE CONNECTORS. DAMAGE CAN
OCCUR TO THE INTERNAL ESDS COMPONENTS.
(1)
Remove the FFCC differential accelerometer. Refer to the latest revision of GEAE
CF34-10E Engine Manual (EMM TASK 77-00-00-800-821/200).
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
000-802-A/400
Page 9 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
TASK 77-31-03-400-802-A
EFFECTIVITY: ALL
5.
General
(1)
(2)
(3)
The rear accelerometers are in the engine zones 416 and 426.
(4)
This task refers to the EMM TASK 77-00-00-800-821/200 which contains the procedures to
remove, clean, inspect and install the rear accelerometer. Do only the procedures related to
the installation of FFCC differential accelerometer.
(5)
B.
C.
References
REFERENCE
DESIGNATION
ENGINE ON WING
LOCATION
REFERENCE
416
Engine - LH Powerplant
426
Engine - RH Powerplant
147AL
199AL
414AR
424AR
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
400-802-A/400
Page 10 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
D.
E.
F.
DESIGNATION
Commercially available
DESIGNATION
LOCATION
BUS
LOCATION TIP
MCDU
PAGE
CB
E1 REVERSER
LICC
DC BUS 1
SSPC
E1 START VLV
SPDA2
DC ESS BUS
SPDA2-M4
1
ENGINE
CB
E2 REVERSER
RICC
DC BUS 2
SSPC
E2 START VLV
SPDA2
DC ESS BUS
SPDA2-M5
2
ENGINE
Job Set-Up
SUBTASK 867-008-A
(1)
G.
Make sure that the aircraft is in the same configuration as it was at the end of the
removal task (AMM TASK 77-31-03-000-801-A/400).
Accelerometer - Installation
SUBTASK 420-005-A
CAUTION: DO NOT TOUCH THE ELECTRICAL PINS OF THE CONNECTORS. DAMAGE CAN
OCCUR TO THE INTERNAL ESDS COMPONENTS.
(1)
H.
Install the FFCC differential accelerometer. Refer to the latest revision of GEAE
CF34-10E Engine Manual (EMM TASK 77-00-00-800-821/200).
Job Close-Up
SUBTASK 867-009-A
(1)
Remove all tools, equipment and unwanted materials from the work area.
SUBTASK 410-007-A
(2)
(b)
SUBTASK 862-010-A
(3)
For the LH engine, remove the circuit breaker ring and tag (inoperative - do not
operate) from this circuit breaker and close it:
(4)
For the RH engine, remove the circuit breaker ring and tag (inoperative - do not
operate) from this circuit breaker and close it:
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
400-802-A/400
Page 11 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
SUBTASK 410-009-A
(5)
(b)
SUBTASK 862-011-A
(6)
For the LH engine, on the MCDU (AMM SDS 34-61-00/1), use the sequence in
parentheses to close this SSPC:
(7)
For the RH engine, on the MCDU (AMM SDS 34-61-00/1), use the sequence in
parentheses to close this SSPC:
SUBTASK 866-005-A
(8)
On the control pedestal, remove the DO NOT OPERATE tag from the POWERPLANT
control panel.
(9)
SUBTASK 860-005-A
(10) Remove the DO NOT OPERATE tag from the SLAT/FLAP lever.
SUBTASK 700-005-A
(11) Do the necessary tests after the replacement or repair of the accelerometer (EMM
TASK 72-00-00-700-805/1300).
SUBTASK 861-005-A
(12) Disconnect the external AC power supply from the aircraft (AMM TASK
24-42-02-860-802-A/200).
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
400-802-A/400
Page 12 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
TASK 77-31-03-040-801-A
General
(1)
This task gives the procedure to deactivate the front accelerometer (number 1 bearing
accelerometer).
(2)
(3)
B.
C.
D.
References
REFERENCE
DESIGNATION
ENGINE ON WING
LOCATION
REFERENCE
412AR
413AL
422AR
423AL
DESIGNATION
Commercially available
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
040-801-A/400
Page 13 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
E.
F.
MCDU
PAGE
TYPE
DESIGNATION
LOCATION
BUS
SSPC
E1 START VLV
SPDA2
DC ESS BUS
SPDA2-M4
1
ENGINE
SSPC
E2 START VLV
SPDA2
DC ESS BUS
SPDA2-M5
2
ENGINE
CB
FADEC 1A
LHCBP
DC ESS BUS
ENGINE
1
CB
FADEC 1B
RHCBP
DC ESS BUS
ENGINE
2
CB
FADEC 2A
LHCBP
DC ESS BUS
ENGINE
1
CB
FADEC 2B
RHCBP
DC ESS BUS
ENGINE
2
Job Set-Up
SUBTASK 860-006-A
WARNING: MAKE SURE THAT THE AIRCRAFT IS IN A SAFE CONDITION BEFORE
YOU DO THE MAINTENANCE PROCEDURES. THIS IS TO PREVENT
INJURY TO PERSONS AND/OR DAMAGE TO THE EQUIPMENT.
(1)
Do the procedure to make the aircraft safe for maintenance (AMM TASK
20-00-00-910-801-A/200).
Do the procedure to make the aircraft safe for maintenance of the powerplant (AMM
TASK 71-00-00-910-801-A/200).
SUBTASK 861-006-A
(3)
Connect the external AC power supply to the aircraft (AMM TASK 24-42-02-860-801A/200).
SUBTASK 862-012-A
(4)
For the LH engine, on the MCDU (AMM SDS 34-61-00/1), use the sequence in
parentheses to open this SSPC:
(5)
For the RH engine, on the MCDU (AMM SDS 34-61-00/1), use the sequence in
parentheses to open this SSPC:
SUBTASK 010-012-A
(6)
Embraer 190 - AMM 4223
For the LH engine, open these fan cowls (AMM TASK 71-11-00-910-801-A/200):
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
040-801-A/400
Page 14 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
(7)
G.
413AL
412AR
For the RH engine, open these fan cowls (AMM TASK 71-11-00-910-801-A/200):
423AL
422AR
SUBTASK 040-003-A
(1)
(2)
For the LH engine, open these circuit breakers and put a circuit breaker ring and tag
(inoperative - do not operate) on each one of them:
For the RH engine, open these circuit breakers and put a circuit breaker ring and tag
(inoperative - do not operate) on each one of them:
(3)
Do a check of current ECP and reprogram the ECP. Set the No. 1 Bearing
Accelerometer parameter to "Disable" (EMM TASK 72-00-00-030-803/300).
(4)
For the LH engine, make sure that these circuit breakers are closed:
(5)
For the RH engine, make sure that these circuit breakers are closed:
(6)
Get access to the Engine Maintenance Page on the MFD (AMM SDS 77-41-00/1).
(7)
Make sure that the ECONOMIC DISPATCH message and the fault code 6019 are
shown to the applicable engine.
NOTE:
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
040-801-A/400
Page 15 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
H.
Job Close-Up
SUBTASK 410-010-A
(1)
(2)
For the LH engine, close these fan cowls (AMM TASK 71-11-00-910-801-A/200):
413AL
412AR
For the RH engine, close these fan cowls (AMM TASK 71-11-00-910-801-A/200):
423AL
422AR
SUBTASK 862-013-A
(3)
For the LH engine, on the MCDU (AMM SDS 34-61-00/1), use the sequence in
parentheses to close this SSPC:
(4)
For the RH engine, on the MCDU (AMM SDS 34-61-00/1), use the sequence in
parentheses to close this SSPC:
SUBTASK 700-006-A
(5)
Do the necessary tests after the replacement or repair of the accelerometer (EMM
TASK 72-00-00-700-805/1300).
SUBTASK 861-007-A
(6)
Disconnect the external AC power supply from the aircraft (AMM TASK
24-42-02-860-802-A/200).
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
040-801-A/400
Page 16 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
TASK 77-31-03-440-801-A
General
(1)
This task gives the procedure to reactivate the front accelerometer (number 1 bearing
accelerometer).
(2)
(3)
B.
C.
D.
References
REFERENCE
DESIGNATION
ENGINE ON WING
LOCATION
REFERENCE
412AR
413AL
422AR
423AL
DESIGNATION
Commercially available
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
440-801-A/400
Page 17 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
E.
F.
MCDU
PAGE
TYPE
DESIGNATION
LOCATION
BUS
SSPC
E1 START VLV
SPDA2
DC ESS BUS
SPDA2-M4
1
ENGINE
SSPC
E2 START VLV
SPDA2
DC ESS BUS
SPDA2-M5
2
ENGINE
CB
FADEC 1A
LHCBP
DC ESS BUS
ENGINE
1
CB
FADEC 1B
RHCBP
DC ESS BUS
ENGINE
2
CB
FADEC 2A
LHCBP
DC ESS BUS
ENGINE
1
CB
FADEC 2B
RHCBP
DC ESS BUS
ENGINE
2
Job Set-Up
SUBTASK 860-007-A
WARNING: MAKE SURE THAT THE AIRCRAFT IS IN A SAFE CONDITION BEFORE
YOU DO THE MAINTENANCE PROCEDURES. THIS IS TO PREVENT
INJURY TO PERSONS AND/OR DAMAGE TO THE EQUIPMENT.
(1)
Do the procedure to make the aircraft safe for maintenance (AMM TASK
20-00-00-910-801-A/200).
Do the procedure to make the aircraft safe for maintenance of the powerplant (AMM
TASK 71-00-00-910-801-A/200).
SUBTASK 861-008-A
(3)
Connect the external AC power supply to the aircraft (AMM TASK 24-42-02-860-801A/200).
SUBTASK 862-014-A
(4)
For the LH engine, on the MCDU (AMM SDS 34-61-00/1), use the sequence in
parentheses to open this SSPC:
(5)
For the RH engine, on the MCDU (AMM SDS 34-61-00/1), use the sequence in
parentheses to open this SSPC:
SUBTASK 010-013-A
(6)
Embraer 190 - AMM 4223
For the LH engine, open these fan cowls (AMM TASK 71-11-00-910-801-A/200):
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
440-801-A/400
Page 18 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
(7)
G.
413AL
412AR
For the RH engine, open these fan cowls (AMM TASK 71-11-00-910-801-A/200):
423AL
422AR
SUBTASK 040-004-A
(1)
(2)
For the RH engine, open these circuit breakers and put a circuit breaker ring and tag
(inoperative - do not operate) on each one of them:
(3)
Do a check of current ECP and reprogram the ECP. Set the No. 1 Bearing
Accelerometer parameter to "Enable" (EMM TASK 72-00-00-030-803/300).
(4)
For the LH engine, make sure that these circuit breakers are closed:
(5)
H.
For the LH engine, open these circuit breakers and put a circuit breaker ring and tag
(inoperative - do not operate) on each one of them:
For the RH engine, make sure that these circuit breakers are closed:
(6)
Get access to the Engine Maintenance Page on the MFD (AMM SDS 77-41-00/1).
(7)
Make sure that the fault code 6019 is not shown at the applicable engine FADEC.
NOTE:
Job Close-Up
SUBTASK 410-011-A
(1)
For the LH engine, close these fan cowls (AMM TASK 71-11-00-910-801-A/200):
413AL
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
440-801-A/400
Page 19 of 20
Rev 8 - Nov 21/12
AIRCRAFT
MAINTENANCE MANUAL
(2)
412AR
For the RH engine, close these fan cowls (AMM TASK 71-11-00-910-801-A/200):
423AL
422AR
SUBTASK 862-015-A
(3)
For the LH engine, on the MCDU (AMM SDS 34-61-00/1), use the sequence in
parentheses to close this SSPC:
(4)
For the RH engine, on the MCDU (AMM SDS 34-61-00/1), use the sequence in
parentheses to close this SSPC:
SUBTASK 700-007-A
(5)
Do the necessary tests after the replacement or repair of the accelerometer (EMM
TASK 72-00-00-700-805/1300).
SUBTASK 861-009-A
(6)
Disconnect the external AC power supply from the aircraft (AMM TASK
24-42-02-860-802-A/200).
77-31-03
Copyright by Embraer S.A. All rights reserved See title page for details.
440-801-A/400
Page 20 of 20
Rev 8 - Nov 21/12