Académique Documents
Professionnel Documents
Culture Documents
(Revision B, 6/2015)
Original Instructions
Read this entire manual and all other publications pertaining to the work to be
performed before installing, operating, or servicing this equipment.
Practice all plant and safety instructions and precautions.
General
Precautions Failure to follow instructions can cause personal injury and/or property damage.
Revisions
This publication may have been revised or updated since this copy was produced.
To verify that you have the latest revision, check manual 26311 , Revision Status &
Distribution Restrictions of Woodward Technical Publications, on the publications
page of the Woodward website:
www.woodward.com/publications
The latest version of most publications is available on the publications page. If
your publication is not there, please contact your customer service representative
to get the latest copy.
Proper Use
Translated translation was made. Be sure to check manual 26311 , Revision Status &
Publications Distribution Restrictions of Woodward Technical Publications, to verify whether
this translation is up to date. Out-of-date translations are marked with . Always
compare with the original for technical specifications and for proper and safe
installation and operation procedures.
RevisionsChanges in this publication since the last revision are indicated by a black line
alongside the text.
Woodward reserves the right to update any portion of this publication at any time. Information provided by Woodward is
believed to be correct and reliable. However, no responsibility is assumed by Woodward unless otherwise expressly
undertaken.
Contents
ELECTROSTATIC DISCHARGE AWARENESS ................................................. 1
CHAPTER 1. GENERAL INFORMATION .......................................................... 2
Introduction ............................................................................................................. 2
Quick Start .............................................................................................................. 2
First Time Start Procedure ..................................................................................... 3
Normal Start Procedure .......................................................................................... 7
Electrostatic
Precautions
When replacing a PCB, keep the new PCB in the plastic antistatic
protective bag it comes in until you are ready to install it. Immediately
after removing the old PCB from the control cabinet, place it in the
antistatic protective bag.
Woodward
Chapter 1.
General Information
Introduction
This Power Generation Learning Module was created to help students learn the
basics of the following items:
Synchronizing
Quick Start
The student must have the following items:
The Power Generation Learning Module USB flash memory drive part
number 8447-1012
Woodward
2.
3.
4.
5.
Woodward
This procedure only needs to be performed once. The install will load two
software programs onto your computer. After the files are installed on your
computer, the normal start procedure can be followed.
Double click on the 9927-2187.exe file. This will load the NetSim Control
Executive software and the Toolkit software to your computer using a Power
System Setup Wizard. Microsoft .NET Framework version 4.0 or greater is
required for the NetSim Control Executive software to run. Please load the
Microsoft .NET Framework software, if required, from the Internet. Install the
software in the location specified by the install program.
The module can use the loopback IP address of 127.0.0.1 to run or your
local LAN (Local Area Network).
You dont have to be on a LAN (Local Area Network) network to run the module.
If your computer's operating system is Windows XP, follow these directions:
1. Type in 127.0.0.1 into the Host Name / Address.
2. Select Add.
3. Select Connect.
Woodward
8.
9.
In the "From the list below, select the type of hardware you are installing"
window, select "Network Adapters" from the list and click Next.
In the "Select Network Adapter" window, from the Manufacturer list, choose
Microsoft, then in the Network Adapter window, choose "Microsoft KM-TEST
Loopback Adapter", then click Next.
In the "The wizard is ready to install your hardware" window, click Next.
In the "Completing the Add Hardware Wizard" window, click Finish.
The ToolKit software should say Connected on TCP/IP in the lower left corner.
If your computer is connected to a LAN (Local Area Network), you can use your
computers IP Address for the host name above. To find the IP Address of your
computer, select run from your command window, type in cmd, and execute the
window. Type in the command; IPCONFIG. The IP Address should show up
under your Ethernet Network Adapter. For example, the Address should look
something like this: 192.168.79.1.
The first time you run the module it will ask you to select the Tool Device:
Select Device1.
If you dont see Device1 in the screen above, open up the NetSim Control
Executive software and select Options:
Woodward
Click on OK and close the NetSim Control Executive and the Toolkit. Start up the
simulation model again and follow the steps above. This time the Device1
should appear. If it doesnt show up, it is usually an IP Address issue.
The module should be running, and you are ready to start the learning module.
Woodward
1.
2.
As long as the IP address does not change, the module will connect.
For problems, please check with your IT department or contact Woodward at the
email address in Chapter 2.
This concludes the quick start guide. Please open the Learning Module Guide
(manual 26736) to proceed through the training.
Woodward
Chapter 2.
Product Support and Service Options
Product Support Options
If you are experiencing problems with the installation, or unsatisfactory
performance of a Woodward product, the following options are available:
1. Consult the troubleshooting guide in the manual.
2. Contact the OE Manufacturer or Packager of your system.
3. Contact the Woodward Business Partner serving your area.
4. Contact Woodward technical assistance via email
(PowergenHelpDesk@Woodward.com) with detailed information on the
product, application, and symptoms. Your email will be forwarded to an
appropriate expert on the product and application to respond by telephone
or return email.
5. If the issue cannot be resolved, you can select a further course of action to
pursue based on the available services listed in this chapter.
OEM or Packager Support: Many Woodward controls and control devices are
installed into the equipment system and programmed by an Original Equipment
Manufacturer (OEM) or Equipment Packager at their factory. In some cases, the
programming is password-protected by the OEM or packager, and they are the best
source for product service and support. Warranty service for Woodward products
shipped with an equipment system should also be handled through the OEM or
Packager. Please review your equipment system documentation for details.
Woodward Business Partner Support: Woodward works with and supports a
global network of independent business partners whose mission is to serve the
users of Woodward controls, as described here:
Replacement Parts
When ordering replacement parts for controls, include the following information:
Woodward
51474A.