Académique Documents
Professionnel Documents
Culture Documents
21 {0}
Connection: C1
Type: Base Plate
1: Pinned base plate
Units: SI metric
Design code: ANSI/AISC 360 (ASD)
Column: Mark=C1 Section=W15X8X.5X.5
Grade=A36
d =
381 mm
Root rad. =
3 mm
Fyf =
248 MPa
b =
203 mm
Area =
9669
Fyw =
248 MPa
tf =
12.7 mm
Sx = 1186898
Fu =
400 MPa
tw =
12.7 mm
Zx = 1321010
.Section shear strength . . . . .
479.4 kN
A360 (G2-1) .Section tension strength . . . . 1437.1 kN
A360-(D2-1)
.Section compression strength . . 1437.1 kN
A360 E7
Base plate:
420x240x16
Gr./Fy/Fu=A36/24/400MPa
Welds:
10 FW/414MPa all around column.
Bolts:
4 x M20 A307/N anchor bolts.
Bolt hole dia. . . . . . . . . .
40 mm
No. bolt rows = 2
No. bolt cols. = 2
Spacing of outer bolts, sg = 160 in XX direction.
Spacing of outer bolts, sp = 240 in YY direction.
Embedment length = 300, no hook.
Shear capacity of bolts NOT considered.
No shear key.
Foundation:
Foundation strength, f'c . . . .
21.0 MPa
Grout thickness . . . . . . . . .
25 mm
Rectangular, D . . . . . . . . .
450 mm
B . . . . . . . . .
300 mm
Min. bolt edge distance . . . . .
70 mm
Depth . . . . . . . . . . . . . .
1000 mm
Foundation is reinforced - reinforcement not checked.
Coefficient of friction . . . . .
0.40
MINIMUM ACTION CHECK
(Minima are based on section capacity, not member capacity.)
Specified minimum design actions:
Shear
40.0 kN
Tension
0% of Ns/ ( 1437.1) =
0.0 kN
Compression
0% of Nc/ ( 1437.1) =
0.0 kN
NOTE: Input design actions are not automatically increased if they are less than
the specified minimum actions. Minimum actions may be set in any load case.
This check warns if any design action is less than the specified minimum
for all load cases.
WARNING: Design shear force is less than specified minimum.
INPUT DESIGN
Axial, P .
Shear, Vx .
Shear, Vy .
ACTIONS
. . . . . . . . . . .
. . . . . . . . . . .
. . . . . . . . . . .
-112.2 kN
0.0 kN
0.0 kN
(comp.)
Strength ratio
Required strength
ASD strength
Reference
COMPRESSION ANALYSIS
CHECK 1 - Bearing on Concrete:
Base plate area, A1 . . . . . . . 1.0080E+05 mm2
Geometrically similar area, A2 . 1.1571E+05 mm2
Concrete confinement ratio . . .
1.07
ACI318 10.17.1
Design bearing stress . . . . . .
7.7 MPa
Concrete foundation strength, Nc/ . . . .
771.1
Pass SDG1 p.14
CHECK 2 - Steel Base Plate Bending:
For I section...
a1 . . . . . . . . . . . . . .
29
a2 . . . . . . . . . . . . . .
39
a4 . . . . . . . . . . . . . .
70
a5 . . . . . . . . . . . . . .
584
k . . . . . . . . . . . . . . .
2.28
X . . . . . . . . . . . . . . .
0.11
lambda . . . . . . . . . . . .
0.381
alpha0 . . . . . . . . . . . .
38.72
Modified Thornton plate strength, Ns/ .
Pass ASI DG7 p.32
Min. thickness, tmin . . . . . .
8
SCM13 p.14-6
Pc
112.2
6.88
Pc
112.2
11.4
mm
mm
mm
mm
1279.1
mm