Académique Documents
Professionnel Documents
Culture Documents
Alcatel Virtual Network Card for Lower Layers is a software component used by Alcatel Lower Layers Manager
to manage TCP/IP packets through the serial port:
Windows NT 4.0
Installation
To install the Alcatel Virtual Network Card for Lower Layers select the Adapters tab in the Network Control Panel applet.
Click the Add... button in the Adapter tab of the Network Control Panel applet.
Click the Have Disk... button in the Select Network Adapter dialog box.
In the Insert Disk dialog box, type the source path of the driver files copied during installation phase (e.g. C:\WinNT\System32\Drivers\LLmanNIC; type "echo %systemroot%" from a
Command Prompt window to discover the right location of the WinNT folder) and click OK.
Select the LLmanNIC lower Layer Driver Alcatel driver and click OK in the Select OEM Option dialog box.
Configuration
To configure the Alcatel Virtual Network Card for Lower Layers use both the Bindings and the Protocols tabs in the Network Control Panel applet.
Select the bindings of Alcatel Virtual Network Card for Lower Layers in the Bindings tab of the Network Control Panel applet.
Disable any unneeded component.
Selecting the Protocols tab of the Network Control Panel applet, the either a message box or a dialog box may appear.
Click the Yes to save changes.
Select the TCP/IP Protocol and click the Properties button.
Configure the IP Address and the Subnet Mask for the Alcatel Virtual Network Card for Lower Layers and push OK.
Click Close in the Protocols tab of the Network Control Panel applet.
The new configuration of Alcatel Virtual Network Card for Lower Layers will be used at the next restart of the computer.
Windows 2000
Installation
To install the Alcatel Virtual Network Card for Lower Layers run the Add/Remove Hardware Wizard from the Control Panel.
Click the Next button in the Welcome to the Add/Remove Hardware Wizard dialog box.
Select the Add/Troubleshoot a device option and click the Next button in the Choose a Hardware Task dialog box.
When the Choose a Hardware Device dialog box appears select Add a New device and click the Next button.
In the Find New Hardware dialog box select the No, I want to select the Hardware from a list option and click the Next button.
In the Hardware Type dialog box select the Network adapters option and click the Next button.
Click the Have Disk... button in the Select Network Adapter dialog box.
In the Install From Disk dialog box, type the source path of the driver files copied during installation phase (e.g. C:\WinNT\System32\Drivers\LLmanNIC; type "echo %systemroot%" from a
Command Propt window to discover the right location of the WinNT folder) and click OK.
Select the Alcatel Virtual Network Card for Lower Layers and click Next in the Select Network Adapter dialog box.
Click Next in the Start Hardware Installation dialog box.
When the Digital Signature Not Found dialog box appears click Yes.
Click Finish in the Completing the Add/Remove Hardware Wizard dialog box.
Configuration
To configure the Alcatel Virtual Network Card for Lower Layers run the Network and Dial-up connections applet from the Control Panel.
Open the network connection using the Alcatel Virtual Network Card for Lower Layers from the Network and Dial-up connections applet.
Uncheck any unneeded component in the Properties dialog box. Check and select the Internet Protocol (TCP/IP) component and click Properties.
Configure the IP Address and the Subnet Mask and push OK.
Alcatel Virtual Network Card for Lower Layers is now configured.
LAN Aziendale
2. Configurare indirizzo IP
dellapparato GNE e abilitarne
larea OSPF. (SOLO PER IL GNE)
Configuration
Comm/Routing
Interface Configuration
Ethernet Configuration
( Abilitare OSPF )
IP Gateway:
151.98.28.1
SubNetMask: 255.255.254.0
NM
138.10.10.182
DCN
root> netstat rn
138.10.10.161
OSPF
OSPF Area :
182.10.10.0
SubNetMask: 255.255.255.0
ISA Board #2
NE
ISA Board #1
EC
ISA Board #2
ISA Board #1
GNE
EC