Vous êtes sur la page 1sur 4

Method Statement for Installation of

Sanitary Wares and Fittings


By Designmep | October 15, 2016
0 Comment

Scope :
This Method Statement defines the procedures to be followed for the supply and Installations of
Sanitary Wares.
PURPOSE:
The Purpose of this method statement is to ensure that correct materials are installed and agreed
procedures are implemented during work execution.
REFERENCES

Project Specification

Mechanical equipment data sheets

Project drawings

DEFINITION
None

RESPONSIBILITIES

Project Manager will have the overall responsibility on the Project execution, quality
and safety. Also he will maintain the planning progress and coordination of works with
Main Contractor.

Site Mechanical Engineer will be responsible for the day to day activities on site,
materials, drawings, testing & commissioning an allocation of Departmental resources to
the work site.

Charge-hand will be directly responsible for the day to day jobs on site, for assigning
work to the technicians or any other workers assigned to his area.

QA/QC Department will be overseeing the quality requirements and quality control
measures for the project in coordination with the Project Mechanical Engineer as outlined
in the Quality Manual.

Safety Officer will be responsible for the Health and Safety aspects on site as per the
approved Safety Procedures.

METHOD OF WORK
Sanitary Ware Materials

Water Closets

Stainless steel sink

Wash basins

Kitchen Sinks

Sanitary Ware Accessories

Equipment/ Tools

Drilling Machine

Hand Tools (Cutting saw, spanner, pipe wrench, pliers, screw driver etc.)

Handling and Storage

Upon satisfactory receipt of material, the sanitary ware will be segregated according to
model, size and stored accordingly.

Sanitary wares will be stored on a flat surface in well ventilated and covered storage area.

Manufacturers instructions will be strictly followed as applicable.

Store keeper will be responsible for proper storage and maintenance of records as
required.

Installation of Sanitary Fittings/Wares


After completion of plumbing and drainage and completion of floor, wall tiles and room doors,
installation of sanitary wares will commence.
Fixing of Sanitary Fittings
Water Closet.

After getting the civil clearance, the concealed cistern will be assembled and mounted on
the wall as per approved manner as well as manufacturers recommendations.

Prior fixing any sanitary ware, it will be inspected for any damages and approved
material be used.

Fixing holes to be marked and position ascertained prior to drilling. There should not be
any redundant holes.

Cistern water inlet and flush outlet connection will be completed with suitable fittings
and same will be tested before closing the panel/ duct.

Drainage pipe (W.C. outlet/ branch) will be positioned properly to receive the W.C.
connector.

Cut out/opening for W.C. outlet, flush outlet, cistern knob/actuator are to be marked on
the panel and same to be cut as per requirement.

C pan will be mounted on the floor and location of the fixing points will be marked
(space will be provided to allow space for connectors).

Holes will be made on the floors for screwing.

Ensure that W.C. connector rubber seal is correctly located on rim of connector.

Lubricate W.C. spigot and rubber seal of connector.

Insert W.C. spigot into connector and push together.

Joint/cap to wall/ panel and floor sealed with waterproof sealant after commissioning the
system.

Wash Basin

After getting the civil clearance, the water supply and drainage arrangements will be
made clear and tidy.

As per manufacturers recommendation, use basin as a template to determine proper


counter.

For wooden or similar counter-top fixing clips will be used. For marble or similar
counter-top basin, it will be supported on timber framework.

After carefully placing the basin under the rim and joint/cap apply water proof sealant.

Mixer location (as per approved) will be marked on the counter and the same will be cut.

Then mixer will be fitted and water supply, drainage connection will be made.

Kitchen sink

Water supply and drainage arrangements will be made clear and tidy.

Counter with finish to be made perfect and properly levelled.

Install the kitchen sink in the exact position (as specified in the drawing).

Fix the sink mixer and connect with cold and hot water supply with angle valve.

Fix the waste with P-trap (with strainer) and connect to the drain pipe.

Seal the gap between kitchen sink and marble.

Safety
All appropriate safety personal protective equipment shall be worn by workmen such as Hard
Hat, cover all clothing, safety shoes, goggles and gloves whenever required.
Where works is high level, only approved scaffolding and safety belts can be used all personals
should use safety Harness.
Category: Plumbing Method Statements

Vous aimerez peut-être aussi