Académique Documents
Professionnel Documents
Culture Documents
2.
What will be the size of nozzle to shell weld for nozzle weld
configuration? Conforming to Fig.-j of UW-16. (Nom. Shell
thickness = 28 mm., Nom. Nozzle thickness = 16mm., weld
size t2= 12mm)
a.
b.
c.
d.
3.
44 mm
47 mm
48.5 mm
50 mm
8 mm
10 mm
12mm
14 mm
4.
5.
6.
1G
2G
4G
All of the positions
8.
5 min
15 min
10 min
6 min
7.
ASME
ASME
ASME
ASME
30
25
20
30
2T
2T
2T
4T
10.
mm
mm
mm
of above
12.
2.0
2.4
1.2
None
For vessel 2.5 inch thick, MDMT specified was 60F and material of
construction used was SA 515 gr 60, without impact testing.
The vessel failed later due to brittle failure. Maintainance
Department says SA 516 GR 60 should have been used. What is
your assessment?
a.
b.
c.
d.
11.
Full radiography
Spot radiography
May be a, or b depending on joint efficiency
Data is not adequate
Normally required
b.
c.
d.
13.
14.
16.
5 to 32 mm
0 to 16 mm
Any thickness
0 to 32 mm
15.
=
=
200 psi
675 F
M.O.C
=
Allow stress (Ambient) =
Allow stress (675F)
=
a.
b.
c.
d.
17.
6 OD pipe in 1G only
2 OD pipe in 1G only
Any diameter pipe in any position
Pipes smaller than 2 OD in 1G only
20.
19.
350 psig
260 psig
312 psig
None of above
18.
SA 537 Cl.1
18,000 psi
15,000 psi
Accept
Resistance must be reduced to 25 Ohms Maximum
Resistance must be increased to 25 Ohms minimum
Depends on opinion of electrical engineer.
=
=
=
=
0.42 inch.
3.2 in.
6.4 in. O. D.
0.42.
22.
36
40
32
200
For 2:1 Ellip. Head (ID=75 inches), the crown portion would lie
within similar circle of diameter:
a.
b.
c.
d.
24.
Change of P No.
Change of A No.
Change of F No.
Groove design
23.
60
30
54
48
1/8
1/16
3/16
25.
For a vertical with column int. dia. = 48'' and height (tan-tan)
=98 ft., the hydrostatic head for bottom dished head (2:1 Ellip.
type) will be:
a.
b.
c.
d.
26.
40.6 psi
42.4 psi
43.3 psi
None of above
Q. NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
ANSWER
A
C
A
C
C
D
A
C
B
A
A
D
D
A
A
C
A
C
B
A
D
C
A
C
C
C
REFERENCE
ASME V, SE 797, 8.5
ASME VIII, UW 16 (j) Notes
API 510, 5.7 (b)
ASME IX, Tables QW 451, QW 422 & QW - 423
ASME V, Table T-672
ASME IX, QW - 203
ASME V, Table T 276
ASME VIII, UW - 51
API 510, 6.4
ASME VIII, Fig. UCS - 66
API 510 and ASME VIII, Table UCS - 57
API 510, 7.2.10
ASME IX, Table QW 451.1
ASME V, T-652
API 510, 57 (e) and ASME VIII, UG-32 (f)
ASME VIII, UG - 99
General Knowledge
ASME IX, QW 452.3
API 572, 10.3.9
Pad OD = 2d and pad thickness shell thk is always ok
ASME IX, Table QW 256 and QW 402.1
API 510, 5.7 (e)
API 510, 5.7 (e)
ASME VIII, Appendix 8, 8.4
h = 100 ft.; head = 100 x 0.433 = 43.3 psi (BOK)
API 576, 6.2.15 & Fig. 40
10