Académique Documents
Professionnel Documents
Culture Documents
D E S I G N
G U I D E
INTRODUCTION
Duff-Norton has been manufacturing linear actuation products
since 1883. We have earned a reputation for reliable, high quality products meeting the industrial lifting and positioning needs
of our customers worldwide. Duff-Norton has been ISO 9001
registered since 1994.
NOTE
Duff-Norton has made every effort to ensure that the information contained in the
publication is accurate and reliable. Determining the suitability of our products for
specific applications is the users responsibility.
WARNING
The equipment shown in this catalog is intended for industrial use only and should
not be used to lift, support, or otherwise transport people unless you have written
statement from Duff-Norton, which authorizes the specific actuator used in your
applications as suitable for moving people.
TABLE OF CONTENTS
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Actuator Selection Guide . . . . . . . . . . . . . . . . . . . . . . . 10-12
Application Analysis Forms . . . . . . . . . . . . . . . . . . . . . 13-14
Imperial Machine Screw Actuators
Features and specifications . . . . . . . . . . . . . . . . . . . . 15-17
Dimensional drawings . . . . . . . . . . . . . . . . . . . . . . . 18-36
Stainless Steel Actuators
Features, Model Numbers, Performance Specification . . . . . . 37-39
Dimensional Drawings. . . . . . . . . . . . . . . . . . . . . . . 40-42
Anti-Backlash Actuators
Features, Model Numbers, Performance Specification . . . . . . 43-46
Dimensional Drawings. . . . . . . . . . . . . . . . . . . . . . . . . 47
Anode Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-49
Micro-Miniature Actuators . . . . . . . . . . . . . . . . . . . . . . . 50
Imperial Ball Screw Actuators
Features, Model Numbers, Performance Specification . . . . . . 51-53
Dimensional Drawings. . . . . . . . . . . . . . . . . . . . . . . 54-71
Continuous Duty Actuators
Features, Model Numbers, Performance Specification . . . . . . 72-74
Dimensional Drawings. . . . . . . . . . . . . . . . . . . . . . . 75-77
Metric Machine Screw Actuators
Features, Model Numbers, Performance Specification . . . . . . 78-80
Dimensional Drawings. . . . . . . . . . . . . . . . . . . . . . . 81-89
Metric Anti-Backlash Actuators
Features, Model Numbers, Performance Specification . . . . . . . . 90
Dimensional Drawings. . . . . . . . . . . . . . . . . . . . . . . . . 91
Engineering Guide
Frequently Asked Questions. . . . . . . . . . . . . . . . . . . . 92-96
Flange Bolt Information . . . . . . . . . . . . . . . . . . . . . . . . 97
Overhung Load Ratings . . . . . . . . . . . . . . . . . . . . . . . . 98
Lateral Movement Ratings. . . . . . . . . . . . . . . . . . . . . . . 99
Worm Shaft Rotation Chart . . . . . . . . . . . . . . . . . . . . . . 100
Screw Column Strength . . . . . . . . . . . . . . . . . . . . . 101-104
Ball Screw and Nut Life Rating. . . . . . . . . . . . . . . . . . . . 105
Power Actuator Gear Reducer Driven
Features, Model Numbers, Performance Specification . . . . . 106-112
Dimensional Drawings / Positions. . . . . . . . . . . . . . . . 113-114
Power Actuator C-Face Driven
Features, Model Numbers, Performance Specification . . . . . . . 116
Dimensional Drawings. . . . . . . . . . . . . . . . . . . . . . . . 117
B-Face Adaptors. . . . . . . . . . . . . . . . . . . . . . . . . 118-119
Power Actuator HandWheels
Features, Model Numbers, Performance Specification . . . . . . . 120
Actuator Controls
Control Panels . . . . . . . . . . . . . . . . . . . . . . . . . . 121-123
Rotary Limit Switches. . . . . . . . . . . . . . . . . . . . . . 124-126
Potentiometer/Transducer. . . . . . . . . . . . . . . . . . . . . . 127
Digital Position Indicator (Potentiometer) . . . . . . . . . . . . . . . 128
Encoder - Worm Shaft. . . . . . . . . . . . . . . . . . . . . . . . 129
Encoder - Ring Kit . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Digital Position Indicator (Encoders). . . . . . . . . . . . . . . . . 131
Magnetostrictive Position Sensor . . . . . . . . . . . . . . . . . . 132
Rotary Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Power Transmission Components
System Arrangements, Component Selection Guide . . . . . . 134-136
Miter Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . 137-139
Couplings (Chain, Jaw, Gear) . . . . . . . . . . . . . . . . . . 140-141
Connecting Shafts. . . . . . . . . . . . . . . . . . . . . . . . 142-143
Pillow Blocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Flange Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Bellows Boots . . . . . . . . . . . . . . . . . . . . . . . . . . 146-147
Inverted machine screw actuators. . . . . . . . . . . . . . . . . . 148
Terms of sale. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
3
WHATS NEW
New and Improved
B series actuators Duff Norton has re-engineered several existing models keeping both customer preferences
and performance improvements in mind. In most cases, new drop in equivalents are now available. In a few
cases minor dimensional differences exist, but do so with performance improvements in mind.
Please see pages: 18, 19, 24, 54 for more information.
Expanded actuator worm / gear ratio options - throughout our standard machine screw, stainless steel, and
anti-backlash offerings; we now have expanded our gear set options to make it easier for our customers to
achieve their desired performance parameters without involving secondary gearing.
Please see pages 17, 39, 45 for more information.
Metric G series actuators Duff Norton now offers a comprehensive line up of european style metric actuators
from 5kN to 500kN capacities. The G series offering includes both standard and anti-backlash models. These
have become quite popular globally, and have the
added benefit of dropping into the same spot as
our traditional imperial actuators with minimal design adjustments.
See pages 78-91.
IEC Motor adapters designed for our G series
actuators, these include many of the most common
IEC motor sizes.
See pages 118-119.
Upgraded controls capabilities.
See pages 121-122.
Upgraded Magnetostrictive Position Sensing
capabilities.
See page 132.
APPLICATIONS
Packaged Solutions, Countless Applications
Duff-Norton mechanical actuators, screw jacks and power transmission products are the best packaged solution
for your linear actuation needs. With capacities ranging from 500 lb. to 250 tons, no one offers a broader range of
solutions for your application needs. This extensive selection is designed to meet the requirements of the most challenging applications. Benefiting from the latest in advanced design techniques, manufacturing methods, and over
100 years experience, Duff-Norton Mechanical Actuators last longer and run smoother with little maintenance and no
headaches. If you have a linear actuation application, Duff-Norton has the packaged solution for you.
SELECTION GUIDE
1. Define the applications operating parameters:
Total load
Load per actuator (if more than one is required)
Desired lifting speed
Upright Translating
Inverted translating
Upright Rotating
Inverted Rotating
SELECTION GUIDE
6. Verify the actuator selection:
Double check your applications travel requirements, and the actuators ratio. Verify the actuators capacity and
speed. Also, determine which of the following actuator end fittings best suits your applications requirements.
Top Plate
Clevis End
Threaded End
Please see pages 92-105 for more detailed engineering information such as:
Flange bolt information Overhung loads Lateral movement ratings Screw column strengths
Note
Please refer to our Column Strength Charts (pages 101-104) if the lifting screw is loaded in compression. It
may be necessary to select a larger actuator if the maximum recommended screw length, regardless of load, or
maximum load has been exceeded.
Note
As duty cycles are intermittent, there is an inverse relationship regarding an actuators maximum duty cycle and
the load being moved. Please consult our application engineers for assistance in determining the most appropriate actuator.
WARNING
P.O. Box 7010 Charlotte, NC 28241-7010 Ph: 800-477-5002 Fax: 704-588-1994 duffnorton@cmworks.com
Company:
Address:
Phone Number:
Fax Number:
Contact:
Email Address:
1. Type of application:
2. How many actuator units are needed?
3. Stroke (Raise) / Unit:
in.
Yes
8. Operating Cycles:
No
Yes
lbs.
No
per hour
in.
in./min.
(inches per cycle x cycles per hour x hours per day x days per years x years of service required)
in. / lbs.
hours per day
9. Life expectancy:
12. Drive:
Yes
No
Motor-driven
(1, 2, 3, 4)
LH Side
LH Side
(1, 2, 3, 4)
RH Side
(1, 2, 3, 4)
LH Side
(1, 2, 3, 4)
RH Side
* (On select models this is required to allow for proper lubrication of the gearbox.
Choose the option that most closely matches the actual installed position.)
Guided
Unguided
15. Conditions:
Vibration
Impact
Compression
Wet
Corrosive
Tension
Explosion Proof
Other
In-plant
Resale
Lift people
Total
Per System
P.O. Box 7010 Charlotte, NC 28241-7010 Ph: 800-477-5002 Fax: 704-588-1994 duffnorton@cmworks.com
Company:
Address:
Phone Number:
Fax Number:
Contact:
Email Address:
1. Comments:
2. If the environment is explosive or hostile, where will the operator be located?
3. Motor Enclosure:
Open Drip Proof
Totally Enclosed
Wash Down
4. Controls Enclosure:
NEMA 1
NEMA 12/13
NEMA 4
NEMA 4X NEMA 3R
5. Motor Mounting:
Separate
C-Face
Right Angle
In Line
Other
6. Additional Gearing:
None
In Line
Right Angle Integra
Ratio
7. Orientation (description):
8. Controls Mounting:
Wall
Floor
Free Standing
Pedestal
Console
Other
9. Control Requirements:
Volts
Phase
Hz
10. Operation:
Variable Speed
Constant Speed
Multiple Speed
Inch/Jog
Maintained
Position
Velocity
Torque
11. Features:
Soft Start; Acceleration Rate
in/min2
Soft Start/Stop; Acceleration Rate
in/min2
Soft Start/Stop; Acceleration Rate
in/min2
Indicators (specify):
Alarms (specify):
Communication (specify):
Limit Switches (specify voltage & mounting position if mounted on actuator worm shaft extension):
Accuracy for positioning (in.):
Number of positions:
Velocity Regulation:
Duty Cycle (from above):
Acceleration and Deceleration rates (from above):
Line Shaft Accuracy:
Load Conditions (from above):
Duff-Norton Actuators most appropriate for this application:
Controls Needed:
Remote Control
Top Plate
Lifting Screw
Shell Cap
Load Bearings
Worm Gear
Worm
Housing
Coverpipe
Anti-backlash (optional)
FL - TKM - 9002 - 6 - 1R
Model Prefix
R - Reducer
F - C-face Adapter
H - Hand Wheel
L - Limit Switch
E - Encoder
J - Rotary Counter
Travel
Series:
Machine Screw
(90xx, 18xx, 70xx, 25xx)
Special MS
(100xx, 20xx, 80xx, 35xx)
Capacities:
Upright model suffixes end with the
capacity number. Inverted model
suffixes lower the capacity number
by one digit. Rotating model suffixes
raise the capacity number by one
digit.
Model Suffix
B - Boot
L - Single End Worm Ext. Left
R - Single End Worm Ext. Right
1 - Optional Ratio #1
2 - Optional Ratio #2
X - Supplied without cover pipe
M - Base Model
Travel
Key Accessories
B - Boot
E - Encoder
F - C-face Adapter
H - Hand Wheel
J - Rotary Counter
L - Limit Switch
R - Reducer
Screw End
C - Clevis End Screw
CC - Double Clevis Ends
M - Top Plate Screw
P - Plain End Screw
T - Threaded End Screw
Base Model
None - Upright Translating
D - Inverted Rotating
K - Keyed, anti-rotation
U - Upright Rotating
V - Inverted Translating
Model Suffix
L - Single End Worm Extension Left
N - Numeric Gear Ratio 100 turns/inch
R - Single End Worm Extension Right
X - Supplied without Cover Pipe
1 - Alternate Gear Ratio #1
2 - Alternate Gear Ratio #2
1/2
10
15
20
25
35
50
75
100
150
72.0
72.0
108.0
108.0
108.0
108.0
107.5
107.5
14.4
21.9
21.9
21.9
21.9
21.9
22.2
22.4
12.2
36
Capacity (Tons)
Pitch (Std.&Opt.)
Pitch (Numeric)
20
21-23
24
25
26
27
28
29
30
31-32
33
34
35
3/4
1 1/2
2 1/4
2 1/2
3 3/4
4 1/2
0.250
0.125
0.200
0.250
0.250
0.375
0.500
0.500
0.500
0.666
0.666
0.666
0.666
0.750
1.000
1.000
0.320
0.250
0.250
0.250
0.250
0.320
0.320
ACME
ACME
ACME
ACME
ACME
ACME
ACME
ACME
ACME
ACME Mod. Sq. Mod. Sq. Mod. Sq. Mod. Sq. Mod. Sq.
Std.
5:1
5:1
5:1
6:1
6:1
6:1
8:1
8:1
8:1
12:1
12:1
50:1
Optional No. 1
20:1
24:1
24:1
24:1
24:1
24:1
24:1
32:1
32:1
32:1
32:1
36:1
36:1
Optional No. 2
12:1
12:1
12:1
Numeric Ratio
20:1
25:1
25:1
25:1
25:1
25:1
25:1
32:1
32:1
32:1
Std.
20
40
25
24
24
16
16
16
16
16
16
16
16
16
12
50
Optional No. 1
100
96
96
64
48
48
48
48
48
48
48
48
36
Optional No. 2
48
48
32
Numeric Ratio
100
100
100
100
100
100
100
100
100
100
Std.
10
20
20
30
40
50
100
150
200
250
200
Optional No. 1
10
20
20
30
40
50
100
150
200
250
Optional No. 2
10
Numeric Ratio
10
20
20
30
40
50
100
Std.
1/3
1/3
1/2
15
15
25
25
35
Optional No. 1
1/4
1/2
3/4
3/4
1 1/2
1 1/2
1 1/2
2 1/2
2 1/2
11
11
Optional No. 2
3/4
1 1/4
Numeric Ratio
1/4
1/2
1/2
3/4
1 1/2
1 1/2
1 1/2
2 1/2
2 1/2
Std.
13
21
55
120
165
450
750
1430
1811
2220
4000
7500
12000
16000
28110
20000
Optional No. 1
25
50
75
185
400
820
1035
1401
2400
4200
6601
8600
15500
Optional No. 2
75
105
275
Numeric Ratio
25
48
72
175
370
640
925
1500
2411
4040
30.6
18.9
23.1
22.1
24.2
22.1
26.5
20.9
22.0
22.4
17.4
13.3
12.4
12.4
14.2
8.0
Optional No. 1
12.7
13.3
13.3
13.4
16.6
12.1
12.8
11.8
9.7
7.9
7.5
7.7
8.6
Optional No. 2
17.7
19.0
18.1
Numeric Ratio
12.7
13.3
13.2
9.1
8.6
7.5
6.9
5.3
4.6
3.9
40
70
175
460
670
1750
4700
7580
10625
14000
26500
47110
73000
118200
216000
423300
Numeric Ratio
175
460
670
1599
4077
6645
9369
11474
18561
30970
1616
1000
573
1051
766
560
420
220
174
227
126
126
79
98
56
110
Optional No. 1
630
630
631
278
236
115
91
112
66
90
57
81
45
Optional No. 2
630
751
458
Numeric Ratio
630
657
437
270
256
148
102
105
65
94
Std.
Max Load at Full Horsepower and
1750 rpm (lb)
19
5/8
ACME
Std.
Max Worm Speed at Full Load (rpm)
18
5/8
Type
Std.
Efficiency Rating (%)
250
455
527
520
2332
2521
3047
4386
3406
3370
5691
4220
5949
4939
8865
7003
26780
Optional No. 1
400
1156
1888
1064
1791
1276
956
1839
1193
2831
1537
4670
2875
Optional No. 2
1258
2402
2339
Numeric Ratio
400
1210
1162
1031
1944
1646
1074
1714
1187
2946
17
17
35
52
66
93
160
240
410
650
1200
1350
2700
0.1
0.1
0.3
0.3
0.3
0.9
1.4
1.5
2.6
2.5
3.7
5.5
6.5
9.0
12.6
23.0
*For loads from 25% to 100% of actuator capacity, torque requirements are approximately proportional to the load.
** Speed is a function of how the actuator is driven. Please see the indicated pages for more information.
Note: All actuator units can be supplied with standard raises up to 24 inches. Special raises up to 20 feet are available upon request. Closed
height dimensions may increase for actuators supplied with bellows boots. See pages 146-147.
1 18
23
132
3
4
Keyway
.375
15
16
1
8
118
11
3/8-24UNF
16
3
4
11
32
(x 5/16 thick)
3 41
2 83
4 closed
Upright: B9225T
1
116
5
16
9
32
112
241
3/8-24UNF
3
4
Base of Actuator
5/8
Stroke plus 1
3
4
2
Closed
Inverted: B9225TV
13
16
Upright 4
Inverted 2
Top Plate
SK2800-1-29A
2 83
Stroke plus 1
241
.437
3/8-24UNF
1
2
Base of Actuator
5
16
3
4
3
8
9
16
141
5
8
7
8
3
8
2 38
Stroke plus 4 41
Upright 416
Inverted 2 18
Clevis End
B9225-11A
.49
Both Ends
.437
138
3
4
3
8
5
16
3
8
Both Ends
2 38
1
1 16
9
16 5
18
15
116
2 43
Stroke plus 6
9
16
3
8
5
8
Stroke plus 2 41
1000 lb Capacity
4 12
1 18
3
4 Keyway
.375
1 23
32
1
1 16
3/8-24UNF
15
16
1
8
1 18
3
4
11
32
(x 5/16" thick)
1
34
2 38
4 Closed
Upright: B9250T
1
1 16
5
16
9
32
112
241
3/8-24UNF
3
4
Base of Actuator
5/8
Stroke plus 1
3
4
3
28
Stroke plus 1
Inverted: B9250TV
13
16
Top Plate
SK2800-1-29A
Upright 4
Inverted 2
1
24
.437
3/8-24UNF
1
2
Base of Actuator
5
16
3
4
3
8
9
16
141
5
8
3
8
7
8
Stroke plus 4-1/4
3
28
Upright 416
Inverted 2 18
Clevis End
B9225-11A
.49
Both Ends
3
4
3
8
.437
138
5
16
Both Ends
3
8
1
1 16
9
16 5
18
15
116
2 43
Stroke plus 6
3
28
9
16
3
8
5
8
Stroke plus 2-1/4
1.750+.005
1.702
+.000
-.001
+.003
-.000
3/
1 21/32 DIA.
1/2
FOUR HOLES
13/32 DRILL
EQUALLY SPACED
ON A 3 DIA. B.C.
2 1/2
7
3
L.H. EXT.
4 1/4 DIA.
1 1/8
1 1/8
.500 DIA.
BOTH EXTENSIONS
3 1/2
7/16
4 1/16
RAISE - 1/4
5 1/4 CLOSED
Upright: M-7002
13/32 DIA.
1 3/4
3 1/2
7/16
Inverted
3/4-10 UNC-2A THREAD
6 CLOSED
1 DIA.
EQUAL TO RAISE
3 3/4
1 3/4 CLOSED
Inverted: M-7001
1 1/8
FOUR HOLES
13/32" DRILL
EQUALLY SPACED
ON A 2 3/8 DIA. B.C.
2 1/2 CLOSED
1 1/2 DIA.
5/8 DIA.
+.000
-.002
Threaded End
3/4
3 1/4 DIA.
1 1/8
Base of Actuator
1 DIA.
4 1/4 DIA.
Upright
1 21/32 DIA.
1/2
1 1/2
RAISE + 2 3/8
4 1/16
3/4
5/8
3 3/4
RAISE + 2 3/8
1 18
13
32
3 x 3 x
16 32
6 14
1.755
1.745
1
2
1 Keyway Type
5
8
1 21
32
18UNF-2A Thread
1.705
1.702
5 14
7
8
2.42 1.93"
5 14
3 18
3 34
Stroke + 78
Upright: B9003T
4 18
5
8
121
32
5 14 Upright
18UNF-2A Thread
2 18 Inverted
7
8
2 18
13
4 14
1
12
7
16
Base of Actuator
32
1.00
3 4
Base of Actuator
1 12
2 12
.625
Clevis End
SK9003-18A
138
5
16
3 34
Both Ends
1
1 16
2 43
Stroke plus 6
5
16
3
4
Stroke +3 38
Doubleraise
Clevis:
B9225CC
Maximum allowable
in compression
14 - rating
3000
lbs
maximum
raise
at
rated
load in compression 9
Maximum Allowable Raise in Compression 7 - Rating 500 lbs.
3 34
1
Stroke +316
3
4
15
116
5
8
3
4
5
8
3
4
9
16 5
18
4 Holes
9
32
on
2.75 Circle
2
Upright
Inverted
1 12
3
8
Inverted: B9003TV
.625
1
616
3 11
16
.49
Both Ends
3 34
15
18
Top Plate
SK9003-6A
Stroke + 78
5 Ton Capacity
15 Ton Capacity
25 Ton Capacity
Upright: M-9050
4 1/2 Diameter x .666 Lead Lifting Screw
Upright
Inverted
Threaded End
Inverted
Upright
Inverted: M-9049
Clevis End
Upright
Double Clevis: CCM-9050
Maximum Allowable raise in Compression 93 - Rating 94,000 lbs.
Maximum Raise at rated load in compression is 90
75 Ton Capacity
Guide Bushing
Carbon Steel
Load Bearings
Bronze
Worm Gear
Worm
Housing
316 S.S.
FL - TSM - 9002 - 6 - 1R
Model Prefix
Travel
R - Reducer
F - C-face Adapter
H - Hand Wheel
L - Limit Switch
E - Encoder
J - Rotary Counter
Series:
Machine Screw
(90xx, 18xx, 70xx, 25xx)
Special MS
(100xx, 20xx, 80xx, 35xx)
(1800 series base configurations
are available only on 2 and 50
Ton models)
Capacities:
Upright model suffixes end with
the capacity number.
Inverted model suffixes lower the
capacity number by one digit.
Rotating model suffixes raise the
capacity number by one digit.
D - Inverted Rotating
U - Upright Rotating
SM - Base Model
Model Suffix
B - Boot
L - Single End Worm Ext. Left
R - Single End Worm Ext. Right
1 - Optional Ratio #1
2 - Optional Ratio #2
X - Supplied without cover pipe
10
15
20
25
35
50
100
0.67
1.66
3.33
5.00
6.66
8.33
11.66
16.66
33.33
1 1/2
0.375
0.250
ACME
6:1
24:1
12:1
25:1
17
67
33
100
10
10
10
10
4
3/4
2
3/4
450
185
275
175
150
66
95
57
22.1
13.4
18.1
9.1
21.1
12.0
16.8
8.0
1750
1599
581
460
35
0.9
2
0.500
0.250
ACME
8:1
24:1
25:1
17
50
100
20
20
20
5
1 1/2
1 1/2
750
400
370
253
141
67
26.5
16.6
8.6
25.1
15.0
7.5
4700
4077
1565
551
52
1.4
2 1/4
0.500
0.250
ACME
8:1
24:1
25:1
17
50
100
20
20
20
5
1 1/2
1 1/2
1430
820
640
471
276
109
20.9
12.1
7.5
20.3
11.5
5.8
7580
6645
2527
959
66
1.5
2 1/2
0.500
0.250
ACME
8:1
24:1
25:1
17
50
100
30
30
30
5
1 1/2
1 1/2
2050
1170
925
676
394
144
22.0
12.8
6.9
18.8
10.7
5.4
10625
9369
3538
1199
93
2.6
3
0.666
0.320
ACME
10 2/3:1
32:1
32:1
16
48
100
40
40
40
8
2 1/2
2 1/2
2700
1700
1500
926
593
336
22.4
11.8
5.3
17.9
9.3
4.5
14000
11474
4665
2328
160
2.5
3 3/4
0.666
0.320
ACME
10 2/3:1
32:1
32:1
16
48
100
50
50
50
8
2 1/2
2 1/2
4000
2400
2411
1366
833
350
17.4
9.7
4.6
17.0
9.3
4.5
26500
18561
8828
2358
240
3.7
4 1/2
0.666
0.320
Mod. Sq.
10 2/3:1
32:1
32:1
16
48
100
100
100
100
15
6
6
7500
4200
4040
2566
1466
619
13.3
7.9
3.9
12.9
7.5
3.6
47110
30970
15697
4087
410
5.5
6
0.750
Mod. Sq.
12:1
36:1
16
48
Lifting Screw
Performance Specifications
Diameter (in)
1
Pitch (Std. & Opt.) 0.250
Pitch (Numeric)
Type
ACME
Std.
6:1
Optional No. 1
24:1
Optional No. 2
12:1
Numeric
25:1
Std.
25
Optional No. 1
100
Optional No. 2
50
Numeric
100
Std.
5
Optional No. 1
5
Optional No. 2
5
Numeric
5
Std.
2
Optional No. 1
1/2
Optional No. 2
3/4
Numeric
1/2
Std.
120
Optional No. 1
50
Optional No. 2
75
Numeric
48
Std.
42
Optional No. 1
19
Optional No. 2
27
Numeric
25
Std.
22.1
Optional No. 1
13.3
Optional No. 2
17.7
Numeric
13.3
Std.
20.3
Optional No. 1
10.9
Optional No. 2
15.5
Numeric
10.9
Std. & Opt.
460
Numeric
460
Std. & Opt.
153
Numeric
211
17
0.3
200
200
200
25
11
11
16000
8600
5466
3000
12.4
7.7
12.1
7.4
118200
39396
1200
9.0
*For loads from 25% to 100% of actuator capacity, torque requirements are approximately proportional to the load.
Note: Contact Duff-Norton Customer Service for motorized performance.
17 - 4 PH
Worm Cap.
(Tons)
2 (1800 Series)
2 (9000 Series)
5
10
15
20
25
35
50 (1800 Series)
100
316 SS
Worm Capacity (Tons)
Sustaining
Operating
2
2
5
10
15
20
25
35
50
100
.67
.67
1.66
3.33
5.00
6.66
8.33
11.66
16.66
33.33
Product Specifications
5.50
5.50
7.50
7.75
8.00
10.25
11.75
12.50
13.50
24.00
4.56
4.56
5.88
5.62
6.31
7.13
9.75
9.56
11.38
18.50
1.66
1.66
2.38
2.88
2.88
3.50
4.50
4.50
5.63
7.00
4.25
4.25
4.50
5.75
5.75
5.75
8.50
10.50
11.25
14.00
.50
.50
.60
.94
.94
.94
.94
1.31
1.25
2.94
(+/-.005)
Travel
Travel
Travel
Travel + 3/8
Travel + 9/16
Travel + 1/2
Travel + 1/4
Travel + 1/4
Travel + 5/8
Travel + 1/2
.50
.50
.50
.50
.63
.75
1.00
1.25
1.25
1.50
1.750
1.750
2.250
2.250
2.750
3.250
4.000
4.000
4.750
6.000
3.00
1.56
2.25
2.88
3.00
3.00
3.75
3.75
8.00
10.00
6.00
3.13
4.50
5.75
6.00
6.00
7.50
7.50
16.00
20.00
1.00
1.93
2.25
2.00
2.50
3.00
3.75
4.50
3.00
5.75
(+.000/-.002)
.500
.500
.749
1.000
1.000
1.000
1.375
1.375
1.500
1.750
2.00
5.25
6.50
7.00
7.50
8.75
11.00
12.50
6.00
16.26
3.50
2.06
3.00
3.75
3.88
4.13
5.13
5.13
9.88
12.25
7.00
4.13
6.00
7.50
7.75
8.25
10.25
10.25
19.75
24.50
1.75
2.42
3.00
2.88
3.38
4.13
5.13
6.00
4.88
8.00
3.50
6.25
8.00
8.75
9.25
11.00
13.75
15.50
9.75
20.75
3.50
3.50
4.50
5.50
5.50
5.50
7.00
7.00
11.00
11.50
7.00
7.00
9.00
11.00
11.00
11.00
14.00
14.00
22.00
23.00
1.12
1.12
1.50
1.80
1.80
1.50
2.30
2.10
4.40
3.40
.41
.41
.69
.81
.81
.81
1.06
1.62
1.38
1.88
3.00
3.00
3.00
4.13
4.13
4.13
6.00
7.75
8.75
11.00
.41
.41
.69
.81
.81
1.12
1.38
1.62
1.88
1.88
.75
.88
1.19
1.31
1.38
1.75
2.13
2.63
3.25
3.50
.5
.38
.75
.88
.88
1.13
1.38
1.38
1.88
2.25
Keyseat
Lifting Screw
(Dia./Pitch)
1.702 +.003/-.000
1.702 +.003/-.000
2.188 +.002/-.000
2.598 +.003/-.000
2.598 +.003/-.000
2.598 +.003/-.000
3.750 +.006/-.000
3.750 +.006/-.000
5.313 +.003/-.000
7.500 +.003/-.000
1.00 x .250
1.00 x .250
1.50 x .375
2.00 x .500
2.25 x .500
2.50 x .500
3.00 x .666
3.75 x .666
4.50 x .666
6.00 x .750
Dimensions
A**
B**
F**
G**
2 Ton SMS
5 Ton SMS
10 Ton SMS
15 Ton SMS
20 Ton SMS
25 Ton SMS
35 Ton SMS
50 Ton SMS
100 Ton SMS
5 1/4
7
7 1/2
8 1/2
10
12
13
15
24
1 3/4
2 1/2
3
3
3 1/2
4
5
5 1/2
9
3/4
1
1 1/4
1 1/4
1 1/2
1 3/4
2
2 1/2
3
13/32
21/32
25/32
29/32
1 1/32
1 9/32
1 17/32
1 21/32
2 17/32
3/4
1
1 1/4
1 1/2
1 3/4
2 1/4
2 1/2
3 1/4
4 1/4
6
8
9 1/4
10 1/4
12 1/2
14 1/2
15 1/2
18
25
2 1/2
2 1/2
4 1/4
4 1/4
5
5 3/4
7
8
12
1 1/8
1 1/8
1 5/8
2
2 1/4
3 1/4
3 3/4
4 1/4
5
Dimensions
J
3/4"-10UNC-2A
1"-8UNC-2A
1 1/2"-6UNC-2A
1 3/4"-5UNC-2A
2"-4 1/2UNC-2A
2 1/2"4-UNC-2A
3 1/4"-4UNC-2A
4"4UNC-2A
1 1/2"-12UNC-2A
N**
P**
1
1 1/2
2
2 1/4
2 1/2
3
3 3/4
4 1/2
6
5 1/4
7 1/2
7 3/4
8 1/2
10 1/4
11 3/4
12 1/2
13 1/2
24
1 3/4
2 1/2
2 3/4
2 3/4
3
3
4
3 1/2
12
4 1/4
4 1/2
5 3/4
5 3/4
5 3/4
8 1/2
10 1/2
11 1/4
14
7/16
5/8
15/16
15/16
15/16
15/16
1 5/16
1 1/4
2 15/16
4
4
4
4
4
4
4
4
6
**Closed dimensions may increase for actuator units supplied with bellows boots. Consult Customer Service.
Note: Lifting screws listed above are not keyed, and i.c. must be held to prevent rotation.
Keyed lifting screws and keyed anti-backlash models also available. Consult Customer Service.
13/32
3
11/16
3
13/16
4 1/8
13/16
4 1/8
13/16
4 1/8
1 1/16
6
1 5/8
7 3/4
1 3/8
8 3/4
1 7/8
11
ANTI-BACKLASH ACTUATORS
1/4 to 250 Tons
ANTI-BACKLASH ACTUATORS
Model Numbering System
FL - TKM - 9402 - 6 - 1R
Model Prefix
R - Reducer
F - C-face Adapter
H - Hand Wheel
L - Limit Switch
E - Encoder
J - Rotary Counter
Travel
Series:
Anti-Backlash
(94xx, 48xx, 74xx, 4501)
Special AB
(104xx, 58xx, 84xx, 5501)
Capacities:
Upright model suffixes end with the
capacity number.
Inverted model suffixes lower the
capacity number by one digit. Rotating model suffixes raise the capacity
number by one digit.
Model Suffix
B - Boot
L - Single End Worm Ext. Left
R - Single End Worm Ext. Right
1 - Optional Ratio #1
2 - Optional Ratio #2
X - Supplied without cover pipe
Travel
Key Accessories
B - Boot
E - Encoder
F - C-face Adapter
H - Hand Wheel
J - Rotary Counter
L - Limit Switch
R - Reducer
Screw End
C - Clevis End Screw
CC - Double Clevis Ends
M - Top Plate Screw
P - Plain End Screw
T - Threaded End Screw
Base Model
None - Upright Translating
D - Inverted Rotating
K - Keyed, anti-rotation
U - Upright Rotating
V - Inverted Translating
Model Suffix
L - Single End Worm Extension Left
N - Numeric Gear Ratio 100 turns/inch
R - Single End Worm Extension Right
X - Supplied without Cover Pipe
1 - Alternate Gear Ratio #1
2 - Alternate Gear Ratio #2
Models for actuators with specialized features will have a serialized suffix such as B9225T-0001.
www.duffnorton.com Ph: (800) 477-5002 Fax: (704) 588-1994
44
ANTI-BACKLASH ACTUATORS
1/4
1/2
10
15
18
1/2
0.250
ACME
5:1
20
1/3
19
5/8
0.125
ACME
5:1
40
1/3
20
3/4
0.200
ACME
5:1
20:1
20:1
25
100
100
5
5
5
1/2
1/4
72.0
14.4
21-23
1
0.250
ACME
6:1
24:1
12:1
25:1
24
96
48
100
5
5
5
5
2
1/2
3/4
72.0
21.9
24
1
0.250
ACME
6:1
24:1
12:1
25:1
24
96
48
100
5
5
5
5
2
3/4
1 1/4
108.0
21.9
25
1 1/2
0.375
0.250
ACME
6:1
24:1
12:1
25:1
16
64
32
100
10
10
10
10
4
3/4
2
108.0
21.9
26
2
0.500
0.250
ACME
8:1
24:1
25:1
16
48
100
20
20
20
5
1 1/2
108.0
21.9
27
2 1/4
0.500
0.250
ACME
8:1
24:1
25:1
16
48
100
20
20
20
5
1 1/2
108.0
107.5
107.5
21.9
22.2
22.4
12.2
28
29
30
31-32
33
34
35
36
2 1/2
3
3 3/4
4 1/2
5
6
7
9
0.500
0.666
0.666
0.666
0.666
0.750
1.000
1.000
0.250
0.320
.320
.320
ACME ACME ACME Mod. Sq. Mod. Sq. Mod. Sq. Mod. Sq. Mod. Sq.
8:1 10 2/3:1 10 2/3:1 10 2/3:1 10 2/3:1
12:1
12:1
50:1
24:1
32:1
32:1
32:1
32:1
36:1
36:1
20
25
35
50
75
100
150
250
13
21
1/4
55
25
1/2
120
50
75
1/2
165
75
105
3/4
450
185
275
1 1/2
750
400
30.6
18.9
25
23.1
12.7
48
22.1
13.3
17.7
72
24.2
13.3
19.0
175
22.1
13.4
18.1
40
1616
70
1000
12.7
175
175
573
630
630
13.3
460
460
1051
630
630
657
13.2
670
670
766
631
751
437
455
2
0.1
527
2
0.1
520
400
400
5
0.3
2332
1156
1258
1210
17
0.3
2521
1888
2402
1162
17
0.3
25:1
16
48
32:1
16
48
32:1
16
48
32:1
16
48
16
48
16
48
12
36
50
100
30
30
100
40
40
100
50
50
100
100
100
150
150
200
200
250
250
200
30
5
1 1/2
40
8
2 1/2
50
8
2 1/2
100
15
6
15
6
25
11
25
11
35
1 1/2
1430
820
1 1/2
1811
1035
2 1/2
2220
1401
2 1/2
4000
2400
6
7500
4200
12000
6601
16000
8600
28110
15500
20000
370
26.5
16.6
640
20.9
12.1
925
22.0
12.8
1500
22.4
11.8
2411
17.4
9.7
4040
13.3
7.9
12.4
7.5
12.4
7.7
14.2
8.6
8.0
9.1
1750
1599
560
278
458
270
8.6
4700
4077
420
236
256
7.5
7580
6645
220
115
148
6.9
10625
9369
174
91
5.3
14000
11474
227
112
4.6
26500
18561
126
66
3.9
47110
30970
126
90
73000
79
57
118200
98
81
216000
56
45
423300
110
102
105
65
94
3047
1064
2339
1031
35
0.9
4386
1791
1944
52
1.4
3406
1276
1646
66
1.5
3370
956
5691
1839
4220
1193
5949
2831
4939
1537
8865
4670
7003
2875
26780
1074
93
2.6
1714
160
2.5
1187
240
3.7
2946
410
5.5
650
6.5
1200
9.0
1350
12.6
2700
23.0
All actuator units can be supplied with standard raises up to 24 inches. Special raises up to 20 feet are available upon request. Closed height
dimensions may increase for actuators supplied with bellows boots. See page 146-147.
Diameter (in)
Pitch (Std. & Opt.)
Pitch (Numeric)
Type
Std.
Optional No. 1
Optional No. 2
Numeric
Std.
Optional No. 1
Optional No. 2
Numeric
Std.
Optional No. 1
Optional No. 2
Numeric
Std.
Optional No. 1
Optional No. 2
Numeric
Std.
Optional No. 1
Optional No. 2
Numeric
Std.
Optional No. 1
Optional No. 2
Numeric
Std.
Optional No. 1
Optional No. 2
Numeric
Std.
Optional No. 1
Optional No. 2
Numeric
Std. & Opt.
Numeric
Std. & Opt.
Numeric
10
20
25
35
50
100
0.67
1.66
3.33
5.00
6.66
8.33
11.66
16.66
33.33
1
0.250
ACME
6:1
24:1
12:1
25:1
25
100
50
100
5
5
5
5
2
1/2
3/4
1/2
120
50
75
1 1/2
0.375
0.250
ACME
6:1
24:1
12:1
25:1
17
67
33
100
10
10
10
10
4
3/4
2
3/4
450
185
275
2
0.500
0.250
ACME
8:1
24:1
25:1
17
50
100
20
20
20
5
1 1/2
1 1/2
750
400
2 1/4
0.500
0.250
ACME
8:1
24:1
25:1
17
50
100
20
20
20
5
1 1/2
1 1/2
1430
820
15
2 1/2
0.500
0.250
ACME
8:1
24:1
25:1
17
50
100
30
30
30
5
1 1/2
1 1/2
2050
1170
3
0.666
0.320
ACME
10 2/3:1
32:1
32:1
16
48
100
40
40
40
8
2 1/2
2 1/2
2700
1700
3 3/4
0.666
0.320
ACME
10 2/3:1
32:1
32:1
16
48
100
50
50
50
8
2 1/2
2 1/2
4000
2400
4 1/2
0.666
0.320
Mod. Sq.
10 2/3:1
32:1
32:1
16
48
100
100
100
100
15
6
6
7500
4200
6
0.750
Mod. Sq.
12:1
36:1
16
48
48
42
19
175
150
66
370
253
141
640
471
276
925
676
394
1500
926
593
2411
1366
833
4040
2566
1466
5466
3000
27
25
22.1
13.3
17.7
13.3
20.3
10.9
15.5
10.9
460
460
153
211
17
0.3
95
57
22.1
13.4
18.1
9.1
21.1
12.0
16.8
8.0
1750
1599
581
460
35
0.9
67
26.5
16.6
8.6
25.1
15.0
7.5
4700
4077
1565
551
52
1.4
109
20.9
12.1
7.5
20.3
11.5
5.8
7580
6645
2527
959
66
1.5
144
22.0
12.8
6.9
18.8
10.7
5.4
10625
9369
3538
1199
93
2.6
336
22.4
11.8
5.3
17.9
9.3
4.5
14000
11474
4665
2328
160
2.5
350
17.4
9.7
4.6
17.0
9.3
4.5
26500
18561
8828
2358
240
3.7
619
13.3
7.9
3.9
12.9
7.5
3.6
47110
30970
15697
4087
410
5.5
12.4
7.7
12.1
7.4
118200
39396
1200
9.0
200
200
200
25
11
11
16000
8600
*For loads from 25% to 100% of actuator capacity, torque requirements are approximately proportional to the load.
Note: Contact Duff-Norton Customer Service for motorized performance.
ANTI-BACKLASH ACTUATORS
How it Works
Tension
Load
www.duffnorton.com Ph: (800) 477-5002 Fax: (704) 588-1994
46
Compression
Load
ANTI-BACKLASH ACTUATORS
Upright
Upright
Upright
Inverted
Inverted
Capacity
A Dia.
D Dia.
(Tons)
(in)
(in)
(in)
(in)
(in)
(in)
1.66
1.66
2.25
2.25
2.75
3.38
3.63
4.00
5.50
6.50
7.00
2.38
3.84
3.88
4.34
5.44
5.75
6.13
7.75
9.69
9.44
11.75
1.25
1.50
2.25
2.25
2.75
3.38
3.63
4.00
5.50
6.50
7.00
.81
.38
.63
.63
.88
1.13
1.25
1.00
1.25
1.25
3.00
2.88
3.38
3.88
4.34
5.44
5.75
6.13
7.75
9.69
9.44
11.75
Pipe Length
.75
1.25
1.25
1.75
2.00
2.00
1.50
2.25
2.38
3.00
Inverted
Anode Jacks
Inverted Translating
Style Anode Jack
Anode Jacks
Elasticone Cover
Optional
ns
In addition to these jacks, Duff-Norton can also supply anode-jacking arrangements, which include the motor, reducer, shafting and couplings for your complete system requirements.
Oversized Clevis,
Knurled Ring, &
Cover Pipe
Special Corrosion
Resistant Paint
Connecting Link,
Clevis Pinned
Screw, & Lifting Nut
Specifications
revolution counter.
Micro-Minature Actuator
Rated
Screw
Turns of Worm
No Load
Lifting Torque
Worm Gear
Model No.
Capacity
Dia.
B9225MM-xxx
B9225MMS-xxx
1000 lbs.
1000 lbs.
.625
.625
Shell Cap
Torque
at Full Load
Ratio
Weight
and Housing
500
500
2 In.-Lbs.
2 In.-Lbs.
18 In.-Lbs.
18 In.-Lbs.
20:1
20:1
2 Lbs.
3 Lbs.
Aluminum
Stainless Steel
Note: The load bearings inside stainless steel actuators are not stainless steel.
Specifications
7 16 "
.375
3
1
3
4
" Thd.
7
28 "
3"
-24UNF
8
Clear Plastic
Cover
5
16 "
38 "
28 "
24 "
.94
AGD Grp.2
Dial Indicator
(not included)
.625
11
32
"
1.00
3.25
4
Lifting Screw
Shell Cap
Ball Nut
Housing
Worm Gear
Load Bearings
Worm
Coverpipe
Protects lifting
screw threads.
Stop Disc
www.duffnorton.com
www.duffnorton.com
Ph: (800) 477-5002
Ph: (800)
Fax:477-5002
(704) 588-1994
Fax: (704) 588-1994 PDF:
51
7
FL - TKM - 9802 - 6 - 1R
Model Prefix
R - Reducer
F - C-face Adapter
L - Limit Switch
E - Encoder
J - Rotary Counter
Travel
Series:
Capacities:
Upright model suffixes end with the
capacity number.
Inverted model suffixes lower the
capacity number by one digit. Rotating model suffixes raise the capacity
number by one digit.
B - Boot
L - Single End Worm Ext. Left
R - Single End Worm Ext. Right
1 - Optional Ratio #1
2 - Optional Ratio #2
X - Supplied without cover pipe
Model Suffix
M - Base Model
Travel
Key Accessories
B - Boot
E - Encoder
F - C-face Adapter
H - Hand Wheel
J - Rotary Counter
L - Limit Switch
R - Reducer
Screw End
C - Clevis End Screw
CC - Double Clevis Ends
M - Top Plate Screw
P - Plain End Screw
T - Threaded End Screw
Base Model
None - Upright Translating
D - Inverted Rotating
K - Keyed, anti-rotation
U - Upright Rotating
V - Inverted Translating
Model Suffix
L - Single End Worm Extension Left
N - Numeric Gear Ratio 100 turns/inch
R - Single End Worm Extension Right
X - Supplied without Cover Pipe
1 - Alternate Gear Ratio #1
2 - Alternate Gear Ratio #2
Models for actuators with specialized features will have a serialized suffix such as B9225T-0001.
www.duffnorton.com Ph: (800) 477-5002 Fax: (704) 588-1994
52
Performance Specifications
Capacity
(Tons)
1/2
52
5/8
0.200
5:1
20:1
25
100
0.5
0.5
1/3
1/6
10.5
5.0
9.5
4.0
67.0
39.8
2.8
0.1
1
0.5
35
2001
2101
1150
1223
2
(HL)
287.5 72.0
118.5
57.5
14.4
23.7
53
54-59 54-59 60-61
3/4
1
1
1 11/64
0.200 1.000 0.250 0.413
5:1
6:1
6:1
6:1
20:1
24:1
24:1
24:1
12:1
12:1
12:1
25
6
24
14.526
100
24
96
58.106
12
48
29.053
2
10
3
5
2
10
3
5
10
3
5
1/2
2
2
2
1/4
1/2
1/2
1/2
3/4
3/4
3/4
22
180
50
110
11
80
25
50
110
30
68
21
160
45
100
10
70
20
45
100
25
60
60.6
66.3
58.9
65.7
31.8
37.9
33.2
36.5
53.0
53.1
54.8
5
20
20
21
0.3
0.3
0.3
0.4
1
2
2
7
0.5
0.5
0.5
0.5
1
1
2
70
700
175
440
1432
700
2521
1146
1432
394
1261
630
430
1576
695
1601 1459 5875
3830
1556
458
2729
1734
680
3557
2096
5
(HL)
10
(HL)
10
20
(HL)
6
12.667
8
16.889
8
24 50.667
24 50.667
24
12 25.334
20
10
20
15
50
20
10
20
15
50
20
10
4
4
5
5
5
3/4
3/4 1 1/2 1 1/2 1 1/2
2
2
500
220
800
350
1375
206
90
400
175
625
300
145
410
180
700
300
1270
183
80
290
150
570
270
125
64.7
69.8
56.8
62.8
62.7
36.2
39.3
45.7
41.9
46.5
49.1
50.3
40
40
50
50
115
0.9
0.9
0.9
0.9
1.5
8
8
24
11
24
0.5
0.5
0.5
0.5
2
2
2
1800
850
3500 1700 7000
504
1146
394
900
229
229
525
236
540
151
420
869
20
25
50
108.0 81.0
21.6
20.1
33.4
66
67
68-69
2 1/4
3
4
0.500 0.660 1.000
8:1 10 2/3:1 10 2/3:1
24:1
32:1
32:1
16
16.16 10.67
48
48.48
32
40
40
90
40
40
90
5
8
15
1 1/2 2 1/2
6
700
925
2700
325
475
1500
650
825
2200
300
425
1200
61.2
59.7
67.8
44.2
38.6
41.4
115
235
520
1.5
2.9
5.0
24
24
92
2
2
33
Note: Hold Back Torque is reatraining torque at the worm shaft to keep load from running down.
Lifting torques are proportional to load, down to 25% of rated load.
Note: See page 105 for Ball Screw and Nut Life Expectancy.
All actuator units can be supplied with standard raises up to 24 inches. Special raises up to 20 feet are available upon request. Closed height
dimensions may increase for actuators supplied with bellows boots. See page 146-147.
1 18
3
4
Keyway
1
8
1 23
32
15
16
3/8-24UNF
1
116
.375
3
4
1 18
11
32
x 5/16
thick
5
16
3 13
16
5 Closed
3 14
Stroke + 1
Upright: B9863T
9
32
112
2 14
3 13
16
Stroke + 1
3
4
1 Closed
Inverted: B9863TV
R.80
Over tube
3/8-24UNF
13
16
2 58
.437
3/8-24UNF
1
2
5
8
5
16
3
4
3
8
9
16
17
32
1.21
3
Stroke + 54
238
141
.49
Both Ends
3
4
3
8
9
16
5
16
Both Ends
1
116
3
416
Stroke + 1-5/16
3
8
3
9 8
16
3
Stroke + 34
2 38
Stroke + 7-1/4
1 Ton Capacity
Upright: M-28750
3/4 Diameter x .200 Lead Lifting Screw
Inverted: M-28749
L.H. EXT.
R.H. EXT.
1 1/8
1.705
1.702
.500
DIA. TYP.
.498
1 1/8
1/8 X 1/16 X 1
KEYWAY TYP.
3
2 1/2
3/4-16UNF-2A
THREAD
1 21/32 DIA.
1 1/8
7
6
1.755
1.745
CLOCKWISE ROTATION
RAISES LOAD
5 5/8
7 1/2 CLOSED
3/4 + RAISE
Upright: M-78021
3/8 R TYP.
1/2
4 HOLES
13/32 DIA.
7/8 DIA. SPOTFACE
1 3/4
3 1/2
1 21/32 DIA.
1 1/2 DIA.
4 HOLES
17/64 DIA.
ON 2 3/4 B.C.
7/16
3/4-16UNF-2B
THREAD
DIA.
.750 DIA.
.748
+.008
-.000
1 1/2 SQ.
1 3/16
5/8
3 1/32
1 1/2 DIA.
1/2
1 3/8
CLOSED
Inverted: M-78011
13/32 DIA.
4 HOLES
5 5/8
1 1/8
3 11/16 + RAISE
3 1/4 DIA.
4 1/4 DIA.
3/4 +RAISE
3 3/4
4 1/16
3/4
1 1/2
3
5/8
3 5/8 + RAISE
1 1/8
L.H. EXT.
R.H. EXT.
1 1/8
1.705
1.702
.500
.498 DIA. TYP.
3
2 1/2
1/8 X 1/16 X 1
KEYWAY TYP.
3/4-16UNF-2A
THREAD
1 21/32 DIA.
1 1/8
1 1/8
5 5/8
3/8 R TYP.
4 HOLES
13/32 DIA.
7/8 DIA. SPOTFACE
1 3/4
3 1/2
Upright: M-7802
1 21/32 DIA.
1 1/8
3/4 +RAISE
1 1/2 DIA.
4 1/4 DIA.
3 B.C.
4 HOLES
17/64 DIA.
ON 2 3/4 B.C.
7/16
.750 DIA.
.748
3/4-16UNF-2B
THREAD
1/2 +.008
-.000 DIA.
1 1/2 SQ.
1 3/16
5 5/8
5/8
2 3/8
1 1/2 DIA.
1 3/8
CLOSED
Inverted: M-7801
13/32 DIA.
4 HOLES
3/4 + RAISE
7 1/2
CLOSED
1
2
1/2
1 1/8
3 1/16 + RAISE
3 1/4 DIA.
7
6
1.755
1.745
CLOCKWISE ROTATION
RAISES LOAD
3 3/4
4 1/16
3/4
1 1/2
3
5/8
3 1/16 + RAISE
1 1/8
1.750 +.005
3-1/2
1-21/32 DIA.
1-1/8
1-1/8
3/4-16 UNF-2A
THREAD
CLOCKWISE ROTATION
RAISES LOAD
3/16 WIDE X 3/32 DEEP X
1.0 LONG KEYWAY BOTH
EXTENSIONS
+.000
6-1/4
1.702
5-1/4
+.003
-.000
1-1/8
7-1/4
R.H.
EXT.
L.H.
EXT.
1/2
RAISE + 3/4
9-1/4
Upright: M-98003
1.93
2.42
3-1/8
FOUR HOLES
13/32 DRILL
.88 DIA. SPOTFACE
2-1/16
3/8 R.
4-1/8
1-21/32
DIA.
1-9/16
RAISE + 1-3/4
7-1/4
Inverted: M-98002
1-3/8
CLOSED
FOUR HOLES
25/64 DRILL
EQUALLY SPACED
ON A 3-7/16 DIA. B.C.
+.000
-.002
DIA.
2.125 DIA.
.750
4.20 DIA.
1-1/8
1.386R MAX
OVER RETURN
TUBES
.832
3.395
RAISE + 3-3/4
4-1/16
4-1/2
SK2800-1-2A
SK2800-4-2A
SK2800-1-5A
SK2800-4-5A
5 Ton Capacity
SK2800-1-5A
SK2800-2-5A
SK2800-1-10A
SK2800-4-10A
10 Ton Capacity
SK2800-1-10A
SK2800-4-10A
SK2800-1-20A
SK2800-4-20A
25 Ton Capacity
SK2800-1-25A
SK2800-4-25A
4.44
3-1/4 - 12 UN-2A
1.500 +- .000
.002 TYP
R.H. EXT.
L.H. EXT.
21.75
9.88
R1.88
6.00
10.25
5-9/16 DIA.
2-3/4
5.313
1.875 HOLE
3.25 SPOTFACE
(TYP 4 PLACES)
1-1/4
2-3/4 +
RAISE
21-3/8
25-3/8 CLOSED
Upright: M-9860
5-9/16
DIA.
3-3/4
+ RAISE
21-3/8
3-5/8
Inverted: M-9859
3.756R MAX
OVER RETURN
TUBES
5.880
DIA.
9-3/4
DIA.
6 HOLES
1-1/32 DIA.
ON 8 B.C.
3.250
3.248
5-9/16
DIA.
2.020
12-5/8
1-1/8
3/4
10-7/8
RAISE + 15
3-1/4
3.756R MAX
OVER RETURN
TUBES
2-1/2
11
15 + RAISE
3-1/4
Predictable life.
Continuous operation.
Oil lubricated.
Ball Screw
12 models available.
Capacity 3,500 to 27,000 lbs.
Available with C-Face motor adaptors and
speed reducers.
Oil Seals
Load Bearings
Pipe Plugs
O Ring Seal
Worm Gear
Worm Bearings
and Oil Seals
Each end of worm.
Worm
Cover Pipe
Housing - Aluminum
FL - TKM - 7515 - 6 - 1R
Model Prefix
Travel
R - Reducer
F - C-face Adapter
L - Limit Switch
E - Encoder
J - Rotary Counter
Series:
Capacities:
Model Suffix
B - Boot
L - Single End Worm Ext. Left
R - Single End Worm Ext. Right
1 - Optional Ratio #1
2 - Optional Ratio #2
X - Supplied without cover pipe
25 configured models available. Upright or inverted translating screw, rotating screw available and double clevis.
Maximum load capacities range from 3,500 to 27,000 pounds.
Rated load capacities (load at which actuator life is 1,000 hours) range from 2,000 to 13,000 lbs.
High mechanical efficiency - The units mechanical efficiency (as high as 70%) is due to the heat-treated ball bearing screw
and mating nut, hardened and ground alloy steel worm, wear resistant bronze worm gear and oil bath lubrication.
High thermal efficiency - The continuous duty cycle actuator units have high thermal efficiency (100% on-time at rated
loads and at least 33% on-time at maximum loads)
High speed - Designed to run at a worm speed of 1750 rpm fully loaded. Higher speeds possible with less than capacity
loads. Screw speed up to 120 inches per minute.
Positive action - High reliability; needs no pumps, hoses or valves. Can be synchronized for multiple usage.
Less power required - Efficient design needs less power for given thrust; cuts power requirements.
Worm gearing meets AGMA Standards.
Sand-cast aluminum housings for added heat dissipation.
Available with C-Face motor adaptors and reducers.
Duff-Norton 7500 Series high duty cycle actuators are specifically designed for continuous operation within certain
load limitations (see Maximum Allowable Duty Cycle chart below). The precision worm gear set operates in an oil
bath that improves thermal efficiency.
Max. Capacity
75% Max.
Capacity
7511
7515
7522
100%
33%
33%
100%
67%
67%
Rated
Capacity
100%
100%
100%
Note: Duty cycles are based on 100F temperature rise above ambient not to
exceed 200F using Duff-Nortons standard oil.
Model No.
Max. Speed Cface Driven (in/min)** (pg. 114)
Max. Speed Reducer Driven (in/min)** (pg. 110)
Max. Load Capacity (lbs.)
Rated Load Capacity (lbs. - 1000 hours life)
Lifting Screw (Dia. x Lead)
Worm Gear Ratio
Turns of Worm for 1" Raise
Horsepower per Actuator (Max. @ 1750 RPM)
Key Torque (in-lb)
Starting Torque (in-lb @ Max. Load)
Running Torque (in-lb @ Max. Load)
Hold Back Torque* (lb-ft at Max. Load)
Actuator Efficiency Rating (Percentage)
Weight with Base Raise of 6" (lbs.)
Weight for Each Additional 1" Raise (lbs.)
7511
7515
75151 (HL)
7522
75221 (HL)
118.5
23.0
3,500
2,000
1.17 x .413
6:1
14.526
2
260
75
60
4
63.91
19
.4
102.0
20.0
12,000
5,200
1.50 x .474
8:1
16.889
5
1000
200
170
9
66.52
43
.9
215.5
43.0
5,500
3,200
1.5 x 1.00
8:1
8.000
5
975
450
392
9
64.36
43
.9
81.0
16.0
27,000
13,000
2.25 x .500
10 2/3:1
21.333
10
2400
420
350
12
57.55
95
1.5
215.5
32.0
13,500
12,000
2.25 x 1.0
10 2/3:1
10.667
10
2400
825
685
12
57.55
95
1.5
*Note: Hold Back Torque is resisting torque at the worm shaft to keep load from running down.
All actuator units can be supplied with standard raises up to 24 inches. Special raises up to 20 feet are available upon request. Standard inverted
keyed models do not have a cover pipe (except for the 1-Ton and 75-Ton models). Closed height dimensions may increase for actuators supplied
with bellows boots. See page 146-147.
Note: See page 105 for ball screw and nut life expectancy
Dimensional Specifications
Model
Dimensions (inches)
No.
7511
Upright
7515 or
75151 8 3/4
Upright
7522 or
75221 13 3/4
Upright
7510
Inverted
7514 or
75141 8 3/4
Inverted
7521 or
75211 13 3/4
Inverted
C D
F G H
+.000
+/-.001
3/4
1.12 8.6 4.3
-.002 1/2 R
1.703
16UNF -2A
.500
+.003
+.000
1
2 7/8
2
7
-.000 1.68 11 5.5
-.002 7/8 R
14UNS -2A
2.598
1.000
+.005
+.000
1 3/4
5 1/8 3 3/4 11 -.000 2.38 14 7.0
-.002 1 3/8 R
12UN -2A
3.750
1.000
+.000
+/-.001
3/4
2 3/4 2.20 6
1.12 8.6 4.3
-.002 1/2 R
1.703
16UNF -2A
.500
+.003
+.000
1
2 7/8
2
7
-.000 1.68 11 5.5
-.002 7/8 R
14UNS -2A
2.598
1.000
+.005
+.000
1 3/4
5 1/8 3 3/4 11 -.000 2.38 14 7.0
-.002 1 3/8 R
12UN -2A
3.750
1.000
2 3/4 2.20
Q*
+/-.06
1 1/8 1 21/32
8.4
Y Z
U**
7 O.D. X
4 I.D.
3 /4
1.5
4 1/2 13/32
+/-.06
10.4
5 3/4 11/16
+/-.1
11.2
+/-.1
9.2
1 1/8
2 3/8
7 O.D. X
4 3/4 I.D.
+/-.1
16.6
+/-.1
13.2
2 1/4
3 1/2
9.8 O.D.
X
6.8 I.D.
1
1/2
+/-.06
7 O.D. X
1 1/8 1 21/32
8.4
4 I.D.
3 /4
4 1/2 13/32
+/-.06
10.4
5 3/4 11/16
+/-.1
11.2
+/-.1
9.2
1 1/8
2 3/8
7 O.D. X
4 3/4 I.D.
+/-.1
16.6
+/-.1
13.2
2 1/4
3 1/2
9.8 O.D.
X
6.8 I.D.
1
1/2
*Closed height
Dimension includes diameter of ball screw with indicated lead for right-hand single thread.
**Bellows boot (optional)
Hub Dia. for boot attachment
***Keyway for Model 7511 is 1/8 x 5/64 x 15/16 LG.
NOTE: When ordering, specify load and duty cycle. Keyway for Model 7515 & 7522 is 1/4 x 1/8 x 1 1/2
Dimensional Specifications
No.
UM7512
Upright
Dimensions (inches)
A
7
2 3/4 2.20
2 3/4 2.20
+.000 +.000
+/-.001
1.12 8.6 4.3 -.002 -.002 1/2 R
6
1.703
.750 .500
UM7516
or
8 3/4 2 7/8
2
7
UM75161
Upright
UM7523
or
13 3/4 5 1/8 3 3/4 11
UM75231
Upright
DM7512
Inverted
DM7516
or
8 3/4 2 7/8
2
7
DM75161
Inverted
DM7523
or
13 3/4 5 1/8 3 3/4 11
DM75231
Inverted
U
3.395
4.33 Std
4.937 or 3.65
HL
+.000 +.000
5.5 -.002 -.002 7/8 R
1.000 1.000
+.005
-.000 2.38 14
3.750
+/+.000 +.000
6.706 Std
+/-.1
+/-.005 2.250 Dia.
7.0 -.002 -.002 1 3/8 R 3 3/4 5 1/8 10 1/4 7 1/2 13/16
.10 2 1/4 5.375 or 6.739 1 1/2
7 3/4
3.7500 .500 Lead
1.750 1.000
1.582
HL
+.000 +.000
+/-.001
1.12 8.6 4.3 -.002 -.002 1/2 R
1.703
.750 .500
+/-.1
.895
5 3/4
+/-.1
.832 1.13 4.250
5 1/4
+/-.1
.895
5 3/4
3.395
4.33 Std
4.937 or 3.65
HL
+.000 +.000
5.5 -.002 -.002 7/8 R
1.000 1.000
+.005
-.000 2.38 14
3.750
+.000 +.000
6.706 Std
+/+/-.1
+/-.005 2.250 Dia.
7.0 -.002 -.002 1 3/8 R 3 3/4 5 1/8 10 1/4 7 1/2 13/16
.10 2 1/4 5.375 or 6.739 1 1/2
7 3/4
3.7500 .500 Lead
1.750 1.000
1.582
HL
Dimension includes diameter of ball screw with indicated lead for right-hand
single thead **Keyway for Model UM-7512 is 1/8 x 5/64 x 15/16 LG.
Keyway for Models UM-7516 & UM-7523 is 1/4 x 1/8 x 1 1/2.
NOTE: When ordering, specify load and duty cycle.
8.0
3 /4
+.003
-.000 1.68 11
2.598
+.003
-.000 1.68 11
2.598
Dimensional Specifications
8.0
+/-.1
2 1/4 2 3/4 5 1/2 4 1/2 13/32
.832 1.13 4.250
5 1/4
Model
Dimensions (inches)
No.
A*
D*
J*
7511
10 3/8
1 1/8
3/4"-16-UNF-2A
11 1/2
3/4
1/2" +.008/-.000
10 7/16
7515
11 1/4
1 1/8
1"-14-UNS-2A
13
1 1/4
1 1/4
3/4" +.010/-.000
11 1/4
7522
16 5/8
2 1/4
1 3/4"-12-UN-2A
19 1/8
1 3/4
1 3/4
1 1/4" +.010/-.000
9 13/16
16 5/8
Model
Dimensions (inches)
No.
T*
U*
V*
7511
7/16
1 3/16
13 /32
4 1/4
1 1/2
2 1/4
3 1/8
2 1/16
7515
5/8
1 1/4
11/16
3 1/2
1 3/4
2 7/8
3 3/4
2 1/16
7522
2 5/16
13/16
2 5/8
4 3/4
3 3/8
5 7/8
3 7/16
*Closed dimensions may increase for actuator units supplied with bellows boots. Call Factory.
Note: Lifting screws listed above are not yet keyed. Must be held to prevent rotation.
Travel
Series:
50kN - 200kN
Machine Screw (90xx)
Special MS (100xx)
5kN - 25kN
Machine Screw (2625, 2501, 9002)
Special MS (3625, 3501, 10002)
Capacities:
50kN - 200kN:
Upright model suffixes end with
the capacity number.
Inverted model suffixes lower the
capacity number by one digit.
Rotating model suffixes raise the
capacity number by one digit.
5kN -25kN:
Upright model suffixes lower the
capacity number by one digit.
Rotating model suffixes raise the
capacity number by one digit.
Model Suffix
B - Boot
L - Single End Worm Ext. Left
R - Single End Worm Ext. Right
1 - Optional Ratio #1
2 - Optional Ratio #2
X - Supplied without cover pipe,
but with guide bushing.
Guide Bushings
Product Specifications
5
Diameter (mm)
Lead (mm)
Type
Std.
Optional No. 1
Optional No. 2
Std.
Optional No. 1
Optional No. 2
Std.
Optional No. 1
Optional No. 2
Std.
Optional No. 1
Optional No. 2
Std.
Optional No. 1
Optional No. 2
Std.
Optional No. 1
Optional No. 2
10
25
50
100
150
200
300
500
16
20
30
38
52
58
65
95
115
3
5
6
9
12
12
12
16
16
Metric
Metric
Metric
Metric
Metric
Metric
Metric
Metric
Metric
Trapezoidal Trapezoidal Trapezoidal Trapezoidal Trapezoidal Trapezoidal Trapezoidal Trapezoidal Trapezoidal
5:1
5:1
6:1
6:1
8:1
8:1
8:1
10 2/3:1
10 2/3:1
20:1
24:1
24:1
24:1
24:1
24:1
32:1
32:1
12:1
12:1
0.60
1.00
1.00
1.50
1.50
1.50
1.50
1.50
1.50
0.25
0.25
0.38
0.50
0.50
0.50
0.50
0.50
0.50
0.75
0.23
0.56
0.56
1.13
2.26
2.26
3.39
5.65
11.3
0.56
0.56
1.13
2.26
2.26
3.39
5.65
11.3
0.56
1.13
0.25
0.37
1.49
2.98
3.73
3.73
3.73
6.00
11.2
0.19
0.37
0.56
1.12
1.12
1.12
1.86
4.50
0.56
1.49
2.83
7.53
20.10
56.78
117.1
189.2
275.4
505.7
915.5
3.69
9.34
27.06
63.2
101.4
147.7
305.3
520.5
12.80
36.65
16.9
21.1
19.8
21.0
20.4
18.9
17.3
14.2
13.0
10.8
10.7
11.0
12.6
11.8
10.8
7.8
7.6
15.5
16.3
1.04
2.27
7.71
15.88
23.59
29.94
42.18
100
173
0.04
0.13
0.13
0.40
0.63
0.67
1.16
1.65
2.46
8.48
22.80
76.61
213.37
579.94
943.98
1374.01
2954.25
5749.55
844
469
708
501
304
188
129
113
117
491
378
198
169
105
72
58
83
418
388
2.73
2.69
11.84
16.62
19.42
17.90
15.57
20.32
34.54
2.21
5.34
4.93
8.40
7.74
5.52
6.61
18.01
6.39
12.22
*For loads from 25% to 100% of actuator capacity, torque requirements are approximately proportional to the load. Raises, measured in increments of 25mm, are available up to 6.1 meters, depending on lifting screw diameter and available bar stock length.
Note: Contact customer service for motorized performance.
5 kN Capacity
10 h8 - 0.022
31.4
0.10
0.03
26.7
M10x1.5-6g
3 N9 x 1.8 x 18L
20
=Stroke+9
Tr16x3
15
10
60.5
95 Closed Ht.
Upright: G2625
R29
85
26 0.08
102
M10x1.5-6g
26.7
20
Tr16x3
40 Closed Ht.
=Stroke+9
21
Inverted: G2624
10
60.5
45 B.C.
Base of Actuator
25
4 Holes
9 on
42 Circle
26 0.08
25
10
16
Tr16x3
10 - 00.05
65
95 Upright
Top Plate
G2625-6
25
40 Inverted
60
Travel + 44
60.5
10
56
30
15
25
Base of Actuator
23.81 +-
26 0.08
R.H. Ext.
Clockwise Rotation
Raises Load
120
10
15
115 Upright
60 Inverted
Clevis End
G2625-11
60.5
10
Travel + 44
150
R.H. Ext.
Clockwise
Rotation
Raises Load
35
0
14 h8 - 0.027
44
Tr20x5
M12x1.75-6g
10
33
31.75 + 0.13
0
5 x 3 x 25L
= Stroke
24
88
11
24
Upright: G2501
R36
100
127
400.08
10
44
33
Tr20x5
M12x1.75-6g
24
125 Upright
=Stroke
45 Inverted
80
30
10
55
88
Inverted: G2500
Base of Actuator
11
88
4 Holes
11 on
57 Circle
24
12 k6 ++0.012
0.001
Top Plate
G2501-6
16
35
12
Tr20x5
12
18
30
36
63
Clevis End
G2501-11
Inverted
Travel + 44
82
80
Base of Actuator
20
400.08
10
35
Upright
Travel + 44
145 Upright
65 Inverted
45 Closed Ht.
25 kN Capacity
90
45
13.5
31
13
5x5 key
48.3
M20x2.5
159
43.23
135
62
30
25
50
Stroke + 5
97
145
80
Upright: G9002
105
48.3
30
55
145 Upright
Stroke + 5
55 Inverted
100
40
12
70
Inverted: G9001
Base of Actuator
13.5
97
4 Holes
13.5 on
65 Circle
40
15
20 h9
31.5
40
Top Plate
G9002-6
89
25
Stroke + 64.5
170 Upright
80 Inverted
.16
20 h9
38.1
Base of Actuator
30
99
23
46
79.5
Clevis End
G9002-11
25
9
Stroke + 74
97
38
60
115
18
16
M24x3
60.3
6x6 Key
170
203
55.58
32
76
57.5
35
3 shim
136
Stroke - 2
185
115
Upright: G9005
153
M24x3
60.3
35
185 Upright
65 Inverted
Stroke - 20
18
50
85
65
Inverted: G9004
Base of Actuator
120
136
4 Holes
18 on
85 Circle
65
20
25 h9
114.3
16
55
36.5
Top Plate
G9005-6
30
141
Stroke + 77
210 Upright
90 Inverted
35
20
30
60
25 h9
Base of Actuator
50.8
30
91.5
Clevis End
G9005-11
136
21
84
Stroke + 101
100 kN Capacity
60
140
22
46.8
25h8
227
M36 x 4
180
40
75.5
16
73
65.99
40
52.5
3mm Shim
131
Stroke + 4
200
145
Upright: G9010
191
40
200 Upright
80 Inverted
Stroke + 4
22
131
80
Inverted: G9009
65
110
20
42
Base of Actuator
150
4 Holes
22 on
76.2
120 Circle
25.4
73
35h9
76.2
Top Plate
G9010-6
152.4
50
Stroke + 100
146.5
24
245 Upright
125 Inverted
40
22
65
66
120
Clevis End
G9010-11
Base of Actuator
33
35 h9
50
131.4
30
Stroke + 130
M40X3 THREAD
140
46
70
46
25 h8
240
88
73
R.H.
EXT.
L.H.
EXT.
195
65
66
50
37 typ
R22
248
75
150
26 HOLE
43 SPOTFACE
(4 PLACES)
98
197
16
140
STROKE
Upright: G9015
160
70
23
52
STROKE
75
248 UPRIGHT
108 INVERTED
73
165
STROKE + 102
40
80
310 UPRIGHT
140 INVERTED
140
160
25
BASE OF ACTUATOR
75
40
73
25
140
20
STROKE + 102
86
25
90
30
Clevis End
G9015-11
22 HOLE
(4 PLACES ON
125 B.C.)
40
52
143
108
Inverted: G9014
Top Plate
G9015-6
25
50
140
52
200 kN Capacity
CCW ROTATION EXTENDS
LIFTING SCREW
8x7x40 KEY (TYP)
300
48
85
M48X5 THREAD
150
48
28 h8 TYP
89
281
215
105.5
L.H.
EXT.
R.H
EXT.
66
75
R29 TYP
211
55
26 HOLE
(4 PLACES)
75
150
105.5
265
21
184
STROKE -1
Upright: G9020
BASE OF ACTUATOR
75
170
95
Inverted: G9019
26 HOLE
(4 PLACES ON
135 B.C.)
25
25
58
75
265 UPRIGHT
95 INVERTED
89
Top Plate
G9020-6
45
90
185
65
24
40
80
BASE OF ACTUATOR
75
143
184
195
STROKE + 100
30
25
50
184
89
45
310 UPRIGHT
140 INVERTED
24
Clevis End
G9020-11
184
25
STROKE + 100
65
105
10x8X50 KEY
295
364
Clockwise rotation
extends screw.
M72x4
95.25
LH
EXT.
RH
EXT.
114
35h8
105
140
65
325
39
R34
190
35
227
Stroke + 15
Upright: G9030
260
65
33 Hole
(4 places on 170 B.C.)
BASE OF ACTUATOR
240
Stroke + 14
110
227
115
Inverted: G9029
26 Hole
(6 places on 175 B.C.)
230
125
30
114
75
67
325 UPRIGHT
115 INVERTED
Top Plate
G9030-6
35
140
85
45
Stroke + 180
227
235
40
BASE OF ACTUATOR
110
80
60
120
75
114
167
365 Upright
155 Inverted
39
Clevis End
G9030-11
227
Stroke + 180
25
85
500 kN Capacity
460
120
68
Clockwise rotation
extends screw
12x8x56 KEY
435
M100x4
525
40h8
135
141
90
225
175
390
51
27
276
Stroke + 12
Upright: G9050
200
300
280
150
35
92
90
215 B.C.)
BASE OF ACTUATOR
32.5 Hole
(4 Places on
Stroke + 12
276
26 Hole
(6 places on 200 B.C.)
254
152
90
392 UPRIGHT
152 INVERTED
Top Plate
G9050-6
141
100
152
62
51
276
Stroke + 475
BASE OF ACTUATOR
442 UPRIGHT
167 INVERTED
152
110
75
150
150
Inverted: G9049
141
90
100
217
36
62
Clevis End
G9050-11
276
Raise + 235
G - Base Model
Series:
50kN - 200kN
Anti-backlash (94xx)
Special AB (100xx)
Travel
25kN
Anti-backlash (9002)
Special AB (10002)
Capacities:
50kN - 200kN:
Upright model suffixes end with the
capacity number.
Inverted model suffixes lower the capacity number by one digit.
Rotating model suffixes raise the capacity number by one digit.
Model Suffix
B - Boot
L - Single End Worm Ext. Left
R - Single End Worm Ext. Right
1 - Optional Ratio #1
2 - Optional Ratio #2
X - Supplied without cover pipe,
but with guide bushing.
25kN:
Upright model suffix ends as shown.
Inverted model suffix lower the capacity number by one digit. Rotating model
suffixes raise the capacity number by
one digit.
D - Inverted Rotating
U - Upright Rotating
Product Specifications
5
Diameter (mm)
Lead (mm)
Type
Std.
Optional No. 1
Optional No. 2
Std.
Optional No. 1
Optional No. 2
Std.
Optional No. 1
Optional No. 2
Std.
Optional No. 1
Optional No. 2
Std.
Optional No. 1
Optional No. 2
Std.
Optional No. 1
Optional No. 2
10
25
50
100
150
200
300
500
16
20
30
38
52
58
65
95
115
3
5
6
9
12
12
12
16
16
Metric
Metric
Metric
Metric
Metric
Metric
Metric
Metric
Metric
Trapezoidal Trapezoidal Trapezoidal Trapezoidal Trapezoidal Trapezoidal Trapezoidal Trapezoidal Trapezoidal
5:1
5:1
6:1
6:1
8:1
8:1
8:1
10 2/3:1
10 2/3:1
20:1
24:1
24:1
24:1
24:1
24:1
32:1
32:1
12:1
12:1
0.60
1.00
1.00
1.50
1.50
1.50
1.50
1.50
1.50
0.25
0.25
0.38
0.50
0.50
0.50
0.50
0.50
0.50
0.75
0.23
0.56
0.56
1.13
2.26
2.26
3.39
5.65
11.3
0.56
0.56
1.13
2.26
2.26
3.39
5.65
11.3
0.56
1.13
0.25
0.37
1.49
2.98
3.73
3.73
3.73
6.00
11.2
0.19
0.37
0.56
1.12
1.12
1.12
1.86
4.50
0.56
1.49
2.83
7.53
20.10
56.78
117.1
189.2
275.4
505.7
915.5
3.69
9.34
27.06
63.2
101.4
147.7
305.3
520.5
12.80
36.65
16.9
21.1
19.8
21.0
20.4
18.9
17.3
14.2
13.0
10.8
10.7
11.0
12.6
11.8
10.8
7.8
7.6
15.5
16.3
1.04
2.27
7.71
15.88
23.59
29.94
42.18
100
173
0.04
0.13
0.13
0.40
0.63
0.67
1.16
1.65
2.46
8.48
22.80
76.61
213.37
579.94
943.98
1374.01
2954.25
5749.55
844
469
708
501
304
188
129
113
117
491
378
198
169
105
72
58
83
418
388
2.73
2.69
11.84
16.62
19.42
17.90
15.57
20.32
34.54
2.21
5.34
4.93
8.40
7.74
5.52
6.61
18.01
6.39
12.22
*For loads from 25% to 100% of actuator capacity, torque requirements are approximately proportional to the load.
Raises, measured in increments of 25mm, are available up to 6.1 meters, depending on lifting screw diameter and available bar stock length.
Note: Contact customer service for motorized performance.
Upright Actuators
Inverted Actuators
A Dia
(mm)
B
(mm)
C
(mm)
D Dia
(mm)
E
(mm)
F
(mm)
42.0
42.0
57.2
69.8
85.9
92.2
101.6
165.0
178.0
Pipe Length
Pipe Length
31.8
44.5
50.8
50.8
38.1
60.4
76.2
64.0
97.5
98.5
138.0
146.0
156.0
197.0
227.0
276.0
31.8
31.8
31.8
69.8
85.9
92.2
101.6
165.0
178.0
20.6
9.5
20.6
22.4
28.7
31.8
25.4
31.7
76.2
73.0
85.9
98.5
138.0
146.0
156.0
197.0
227.0
276.0
4. Can the Duff-Norton actuator operate at high speeds?
The input horsepower to these actuators should not exceed the hp rating shown in the specifications table. Maximum RPM should not exceed
1800. We cannot accept responsibility for the overheating and rapid wear that may occur should these limits be exceeded. Horsepower increases
in direct proportion to the speed, and the motor size will be out of proportion to the actuator model design rating should the speed become excessively high. When selecting the maximum permissible speed for an actuating arrangement, always check to see that the hp rating of the actuator
model is not exceeded
17. Can the actuator unit be used within rigid structures or presses?
We recommend that the actuator selected have a greater capacity than the rated capacity of the press or of the load capacity of the structure.
We also recommend that a torque limiting clutch or similar device be used to prevent overloading of the actuator unit. Unless these precautions
are taken, it is possible to overload the actuator unit without realizing it, because it is difficult to determine just what load is being imposed on
the actuator unit.
21. Can bellows boots be supplied for an actuator model with inverted screw?
Yes, but allowance must be made in the length of the lifting screw for both the closed height of the boot and structure thickness. Since we can
make no provision for attaching a boot on the underside of your structure, we suggest that a circular plate similar to the lifting screw top plate
be welded or bolted to the bottom of your structure supporting the actuator unit, thereby making it possible to use a standard bellows boot. (See
pages 146-147.)
22. Can stop discs, stop pins or stop nuts be used on the actuator unit?
Stop disc, pins or nuts can be recommended on the actuator unit that is hand operated. For motor driven units, the full capacity of the actuator
unit or even a greater force (depending on the power of the motor) can be applied against the stop, thereby jamming so tightly it must be disassembled in order to free it. It is suggested that external stops be used where possible. Under ideal conditions where a slip clutch or torque limiting device is used, a stop pin or stop nut may be used - but the Duff-Norton Company should be consulted. The stop disc used on the bottom of
the lifting screw in our ball screw units are not power stops. These are used to ensure that the lifting screw will not run out of the ball nut during
shipping and handling, thereby permitting loss of the recirculating balls.
26. Will the actuator unit drift after the motor is switched off?
Yes, unless a brake of sufficient capacity is used to prevent it. The amount of drift will depend upon the load on the actuator unit and the inertia of
the rotor in the motor. Most Machine Screw models require approximately one-half as much torque to lower the load as it does to raise the load.
For the machine screw actuator unit with no load, the amount of drift will depend upon the size and speed of the motor. For example, a 1750
RPM motor directly connected to an actuator unit (without a load) will give on the average 2- 3 drift; a 500 RPM gear motor will give about
1/9 as much drift. Note that the drift varies as the square of the velocity (RPM). The drift of the actuator unit screw can be controlled by using a
magnetic brake on the motor.
27. Is the torque of a rotating screw actuator unit the same as a standard unit?
The lifting torque, as well as the efficiency and side thrust ratings, are the same for a rotating screw unit. It is understood, however, that the same
pitch and screw diameter are used in each actuator unit, as well as the same worm gear ratio. This comment also applies to the inverted actuator
unit and those with threaded or clevis-style ends.
28. Is the worm gear actuator unit suitable for high temperature operation?
The actuator is normally suitable for operation at ambient temperatures of up to 200F using standard greases and seals. Operation above 200F
will require special lubricants. For temperatures above 300F the life of even special lubricants is limited in direct proportion to increase in
temperature and duration of exposure to such temperatures. At 400F and above, the oil in the grease will vaporize and grease will carbonize and
solidify. Applications of this type should be avoided. For temperatures above 250F advise Duff-Norton of full particulars of the duration of such
temperatures. In some cases, it may be necessary to furnish unlubricated units, then the customer will supply the lubricant of his own choice.
We suggest that a lubricant manufacturer be consulted for type of grease and lubrication schedule. As a general rule, the actuator unit should be
shielded to keep ambient temperatures to 200F or less.
Seals for temperatures above 250F are very expensive. Instead, we would substitute bronze bushings for seals in these cases. If bellows boots
are used, special materials will be required for temperatures above 200F
32. How do you compute the raise per minute with a given worm shaft speed?
When the worm shaft speed is known, the distance the load can be raised per minute can be determined with this formula:
Raise per minute =
or Travel per Worm Turn (mm) x RPM of Worm Shaft (Worm turns for 1 raise are shown in actuator specifications on pages 17, 39, 45, 50, 53 and
74).
33. How do you calculate the RPM of worm shaft necessary to achieve a given rate of raise?
If the application calls for a certain raise per minute, the worm shaft speed which will give the rate of raise can be calculated as follows (or see
tables on pages 108 thru 112).
Worm shaft RPM =
34. How is the Duff - Norton rotary limit switch mounted on an actuator unit?
It is suggested that the actuator unit be purchased with the limit switch factory mounted. The rotary limit switch can be field mounted by following
the instructions found in this book under Rotary Limit Switch. In most cases, the switch is mounted to the worm using the worm flange retainer
bolts. This switch cannot be directly mounted on 1/4 to 1-Ton actuator models.
35. How is the maximum raise determined when using the limit switch?
Maximum raise is determined by the ratio of the switch used and the turns for one inch raise of the actuator unit. The limit switch ratios available
are 10:1, 20:1 and 40:1. Refer to the charts on pages 124-125 or on the inside cover of the limit switch, and use the following formula.
Max. Raise of Actuator Unit (inches) = Max. Input Revolutions of Limit Switch Turns of Actuator Unit Worm for 1 raise
36. How is the rotary limit switch adjusted for position stop?
The Duff-Norton rotary limit switch is infinitesimally adjustable by moving the adjustable nuts of the worm driven screw.
37. Can a multiple actuator unit arrangement be set up to visually indicate position of the lifting screw at any given point?
Yes, in several ways. However, it is suggested you consult the Duff-Norton Company for recommendations based on your particular application.
www.duffnorton.com Ph: (800) 477-5002 Fax: (704) 588-1994
96
ENGINEERING GUIDE
Flange Bolt Information
Refer to respective catalog dimensional drawings for orientation on flange bolts in relation to the horizontal CL for
4-hole pattern and 30 to horizontal CL for 6-hole pattern.
Worm Flange
B.C. Diameter
1/4 Ton
NA
Bolt Information
No Flange Bolts
1/2 Ton
NA
No Flange Bolts
1 Ton
NA
No Flange Bolts
2 Ton
1 11/16"
3 Ton BS
1 11/16"
3 Ton MS
2 3/32"
5 Ton
2 3/8"
10 Ton
3"
15 Ton
2 3/4"
20 Ton
3 1/2"
25 Ton
4 1/8"
35 Ton
4 1/4"
50 Ton
5 1/4"
75 Ton
5 3/4"
100 Ton
6 1/4"
150 Ton
6 1/4"
250 Ton
8 1/4"
ENGINEERING GUIDE
Overhung Load Capacity of Actuator Worm Shaft (lbs.)
Note:
Actuator
Overhung Load
1/4 Ton MS
50
1/2 Ton MS
45
1/2 Ton BS
45
1 Ton MS & BS
55
2 Ton MS & BS
30
3 Ton MS
60
3 Ton BS
120
5 Ton MS&BS
105
10 Ton MS & BS
305
15 Ton MS
390
20 Ton MS & BS
325
25 Ton MS & BS
735
35 Ton MS
665
50 Ton MS & BS
350
75 Ton MS
630
100 Ton MS
650
150 Ton MS
350
250 Ton MS
1310
ENGINEERING GUIDE
Lateral Movement Ratings
Machine Screw Actuators Loads and Raises
Raise
(In.)
1/4
Ton
1/2
Ton
1
Ton
2
Ton
3
Ton
5
Ton
10
Ton
15
Ton
20
Ton
25
Ton
35
Ton
50
Ton
75
Ton
100
Ton
150
Ton
250
Ton
3
6
9
12
15
18
21
24
.040
.085
.090
.115
.140
.165
.190
.215
.050
.075
.105
.135
.165
.195
.225
.255
.020
.030
.040
.050
.060
.070
.080
.090
.020
.035
.055
.070
.090
.100
.120
.135
.020
.035
.055
.070
.090
.100
.120
.130
.030
.050
.070
.090
.110
.1030
.150
.170
.025
.040
.055
.070
.085
.100
.115
.135
.030
.045
.065
.080
.100
.120
.133
.150
.025
.040
.050
.070
.080
.095
.105
.125
.035
.060
.085
.105
.130
.155
.175
.200
.040
.050
.060
.070
.080
.090
.100
.110
.060
.090
.120
.150
.180
.215
.245
.275
.050
.060
.070
.080
.090
.100
.110
.120
.050
.060
.070
.080
.090
.100
.110
.120
.050
.060
.070
.080
.090
.100
.110
.120
.090
.100
.110
.120
.130
.140
.150
.160
Notes:
1. Does not allow for possible deflection due to side thrust.
2. Lateral movements are for information only. For best results, we suggest guides where possible.
3. The above movements apply to machine screw actuator models only and not to the ball screw series.
Permitting lateral movement on the ball screw under load will exert side thrust on the ball screw and ball
nut, and will be detrimental to ball screw and ball screw nut life. Ball screw applications should be guided to
ensure a minimum of lateral movement.
Counter-Clockwise Rotation of
Worm Raises Load
Counter-Clockwise Rotation of
Worm Raises Load
ENGINEERING GUIDE
Load Screw Column Strength Specifications
Machine Screw
Capacity
1/4 Ton MS
1/2 Ton MS
1 Ton MS
2 Ton MS
3 Ton MS
5 Ton MS
10 Ton MS
15 Ton MS
20 Ton MS
25 Ton MS
35 Ton MS
50 Ton MS
75 Ton MS
100 Ton MS
150 Ton MS
250 Ton MS
Ball Screw
Fixed Guided
24
30
33
45
45
64
85
100
116
154
207
256
273
320
386
492
Max. Pin-to-Pin
Length
Pinned Ends
19
24
26
36
36
51
68
80
93
123
166
205
219
256
309
393
Capacity
1/2 Ton BS
1 Ton BS
2 Ton BS
3 Ton BS
5 Ton BS
10 Ton BS
20 Ton BS
25 Ton BS
50 Ton BS
Fixed Guided
30
41
51
54
71
71
116
155
211
Continuous Duty
Capacity
7511 CD
7515 CD
7522 CD
Max. Pin-to-Pin
Length
Pinned Ends
24
33
41
44
57
57
93
124
169
Max. Pin-to-Pin
Length
Pinned Ends
44
57
93
Upright Actuators
U
P
R
I
G
H
T
L
L
I
N
V
E
R
T
E
D
Pinned Ends
Inverted Actuators
Screw Length - Screw lengths for strength curves are defined as shown.
Note: Screw length can be converted to actuator raise or actuator raise can be converted to screw length by use of appropriate dimensional diagrams in the design guide for standard actuator models or special dimensions and dimensional diagrams for
special actuator models.
Caution: Actual loads on any actuator should never exceed catalog load rating for that actuator.
Safety Factor - The loads on the vertical axis for the strength curves are theoretical buckling loads as predicted by
the Euler column formula in sloping portions and twice rated actuator loads in the horizontal portions. See AISC or
other applicable codes for selecting appropriate safety factors.
www.duffnorton.com Ph: (800) 477-5002 Fax: (704) 588-1994
100
ENGINEERING GUIDE
Load Screw Column Strength Specifications
Pinned Ends
Example - Select a standard upright clevis end machine screw actuator for a 14,000 lb. unguided load
and a 25 in. raise. For first approximation assume
screw length equal raise.
1. Select safety factor. For example 1.92 from AISC
specifications.
2. Multiply 14,000 lb. load by 1.92 safety factor to
obtain 26,880 lb. failure load.
3. Locate 26,880 lb. load on vertical axis.
4. Locate 25 in. screw length on upper horizontal
axis scale.
5. Project horizontally right from 26,880 lb. load
and vertically up from 25 in. screw length.
6. Select 9015 actuator since its strength curve
is above the intersection, the 14,000 lb. load is
less than the 30,000 lb. rated load and the 25
in. screw length is less than the 41 in. maximum
permissible screw length.
Recheck actuator selection using true screw length.
Convert 25 in. actuator raise to true screw length.
8.50 in.
ENGINEERING GUIDE
Screw Column Strength Chart
Screw Column Strength Chart
For Inch Machine Screw Actuators to 15 Ton Capacity
1,000,000
100,000
15 ton
10,000
10 ton
5 ton
2 & 3 ton
1 ton
1/2 ton
1,000
1/4 ton
100
0
10
15
20
25
30
35
40
45
10
20
30
40
50
60
70
80
90
100
0
15
30
45
60
75
90
105
10,000,000
1,000,000
250 ton
150 ton
100 ton
100,000
75 ton
50 ton
35 ton
t
25 ton
20 ton
t
10,000
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
20
40
60
80
100
120
140
160
180
200
220
240
260
280
300
320
340
360
380
32
52
72
92
112
132
30
60
90
120
150
180
210
240
270
300
330
360
390
420
450
480
39
69
99
129
159
ENGINEERING GUIDE
Screw Column Strength Chart
Screw Column Strength Chart
For Inch Stainless Steel Actuators
1,000,000
100 ton
100,000
50 ton
35 ton
25 ton
15 ton
10 ton
10,000
20 ton
5 ton
2 ton
1,000
100
0
10
20
30
40
50
60
70
80
90
100
110
120
10
20
30
40
50
60
70
80
90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260
PIN TO PIN LENGTH (in) PINNED ENDS
15
30
45
60
75
90
105 120 135 150 165 180 195 210 225 240 255 270 285 300 315
SCREW LENGTH (in) FIXED-GUIDED
100,000
50 ton
25 ton
20 ton
10,000
5 & 10 ton
1 ton
3 ton
2 ton
1/2 ton
1,000
100
0
10
20
30
40
50
60
70
80
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
15
30
45
60
75
90
105
120
135
150
165
180
195
210
ENGINEERING GUIDE
Screw Column Strength Chart
100,000
7522
10,000
7515
7511
1,000
100
0
10
15
20
25
30
35
40
45
10
20
30
40
50
60
70
80
90
10
20
30
40
50
60
70
80
90
100
110
1,000
200 kN
100
150 kN
100 kN
50
25 kN
10 kN
5 kN
10
0
100
200
300
400
500
600
700
800
900
1000
1100
200
400
600
800
1000
1200
1400
1600
1800
2000
2200
2400
200
400
600
800
1000
1200
1400
1600
1800
2000
2200
2400
2600
2800
3000
1200
ENGINEERING GUIDE
Ball Screw and Nut Life Rating
Predicting screw and nut life lets you forecast necessary replacement, saving time and money. It also permits
selection of the most economical screw size.
Use caution when installing the ball screw. The life expectancy listed below may be greatly reduced if ball screws
are subjected to misalignment, shock loads, side thrust, environmental contamination or lack of lubrication and
maintenance.
It is possible to estimate the minimum life of the Duff-Norton ball screw and nut only. Because of the many variable
operating conditions, we can not predict the life of the worm and gear set in the ball screw actuators.
*5 ton and 10 ton models use the same screw and nut.
Capacity (Tons)
1/2
1
2
2 - High Lead
3
5
5 - High Lead
10
10 High Lead
20
25
50
100% of
75% of
50% of
Model
0.75
0.5
0.25
0.1
Full Load
470,000
110,000
65,000
150,000
210,000
1,000,000
440,000
130,000
50,000
150,000
700,000
630,000
Full Load
1,100,000
250,000
150,000
360,000
650,000
2,400,000
1,000,000
300,000
130,000
360,000
1,600,000
1,500,000
Full Load
3,700,000
860,000
520,000
1,200,000
2,200,000
8,100,000
3,500,000
1,000,000
430,000
1,200,000
5,600,000
5,000,000
No.
7511
7515
7522
Max. Allow. Duty
Cycle @ 1750
RPM Input
Max. Cap.
1.10
.44
.64
Max. Cap.
2.70
1.00
1.50
Max. Cap.
9.50
3.70
5.50
Max. Cap.
60.00
34.00
50.00
Max. Cap.
150.00
110.00
130.00
33%
67%
100%
100%
100%
Note: Duty Cycles are based on a 100F temp. rise not to exceed 200F using
Duff-Nortons standard oil.
*Life expectancies listed are L10 values - values where 10% of screw can,
statistically, be expected to fail.
"B"
"A"
.822
.812
1.104
1.104
1.587
1.981
1.718
1.981
1.718
2.561
3.349
4.029
Radius
.797
.875
1.194
1.194
1.386
1.690
1.720
1.690
1.720
2.272
3.076
3.756
"C"
1.000 Sq.
1.250 Sq.
1.500 Sq.
1.500 Sq.
2.125 Dia.
2.625 Dia.
2.625 Dia.
2.625 Dia.
2.625 Dia.
3.375 Dia.
4.751 Dia.
5.990 Dia.
POWERED ACTUATORS
All actuators require an external power source. Whether
this power source be an electric motor or hand wheel
Duff-Norton has the required component.
Customers who choose to power their actuators with an
electric motor may do so by connecting the motor to the
actuator via a C-face adapter, right angle gear reducer,
or by remotely connecting the motor and actuator worm
shaft with a coupling and connecting shaft.
Some customers opt to manually power their actuators.
In those cases hand wheels are usually the preferred
drive component.
POWERED ACTUATORS
How to size a Motorized Gear Reducer
Determine whether machine screw or ball screw actuators are to be used. Determine if it is a single actuator
application, or multiple actuators, shaft driven from a common motorized reducer.
For a single actuator:
1. Determine actuator load.
2. Refer to the tables on pages 108-112. Select an actuator model with adequate nominal load rating. Ratings
larger than actual load may be required due to column strength, life requirements, etc.
3. Select a reducer ratio to provide a suitable lifting speed.
4. Go along that line of the table to find a load capacity equal to or greater than applied load. Note the motor
horsepower from the top of the column.
Note: Ratings in the shaded area of the chart exceed the safe load rating of a single actuator and are shown for designing multiple actuator
systems. In no case should an actuator be used at a higher load or input horsepower than shown in the actuator specification charts on pages 17,
39, 45, 50, 53 and 74.
POWERED ACTUATORS
Machine Screw Actuators - Performance Specifications
The gear reducers shown in this section are sized with adequate power ratings to allow a single actuator to be
used at its full load or horsepower rating. For multiple actuator applications, the reducers shown may not provide
adequate power to operate several actuators at full rating. Oversized reducers are available. Contact Duff-Norton
Customer Service for multiple actuator applications if the total capacity is greater than shown.
Lifting
Speed
(in/min)
14.4
9.6
7.2
4.8
3.6
2.9
2.4
1.8
14.4
9.6
7.2
4.8
3.6
2.9
2.4
1.8
21.9
14.5
10.9
7.3
5.5
4.4
3.6
2.7
21.9
14.5
10.9
7.3
5.5
4.4
3.6
2.7
21.9
14.5
10.9
7.3
5.5
4.4
3.6
2.7
21.9
14.5
10.9
7.3
5.5
4.4
3.6
2.7
5800
8330
10900
14900
8700
12500
11600
3700
5350
7000
9700
12430
15000
16200
18000
4480
6600
8580
12090
15520
18800
20600
25500
3570
5240
6900
9750
12640
15500
16200
21300
3320
4870
6410
9060
11700
14400
15100
19800
5550
8020
10500
14500
18000
7400
10700
14000
18000
11100
16090
Note: Model 50
reducer requires
140 Frame motor for
3HP application
6720
10000
12860
18100
23300
28200
30900
37700
5350
7860
10340
14600
18960
23300
24200
31900
4980
7300
9600
13600
17550
21600
22650
29700
8960
13200
17150
24180
31000
37600
37700
13400
19800
25730
36200
22400
33700
7140
10480
13800
19500
25300
31000
32300
42600
6640
9740
12800
18100
23400
28800
30200
39600
10700
15700
20700
29250
37900
46400
17850
26200
34500
46400
26750
39300
9960
14600
19200
27200
35100
43200
43200
16600
24300
32000
45000
24900
36500
43200
POWERED ACTUATORS
Machine Screw Actuators - Performance Specifications
Actuator Actuator
Model
Ratio
25 Ton MS
35 Ton MS
50 Ton MS
10.33:1
10.33:1
10.33:1
Lifting
Reducer Reducer Speed
Model
Ratio
(in/min)
4.85
22.2
5.46
19.7
5.92
18.2
6.78
15.9
7.73
13.9
8.71
12.4
9.78
11.0
11.02
9.8
12.64
8.5
14.08
7.7
92672
16.08
6.7
18.08
6.0
20.37
5.3
23.28
4.6
26.55
4.1
29.91
3.6
34.17
3.2
37.32
2.9
42.04
2.6
48.03
2.2
51.86
2.1
4.81
22.4
5.43
19.9
6.11
17.6
6.41
16.8
7.60
14.2
8.55
12.6
9.63
11.2
10.88
9.9
12.43
8.7
13.91
7.8
92772
15.60
6.9
17.83
6.0
19.73
5.5
22.22
4.9
25.39
4.2
28.44
3.8
32.04
3.4
36.61
2.9
40.77
2.6
45.93
2.3
52.48
2.1
8.83
12.2
9.39
11.5
10.21
10.6
11.40
9.5
13.40
8.0
15.66
6.9
18.20
5.9
9042
20.32
5.3
23.89
4.5
27.91
3.9
31.70
3.4
34.39
3.1
40.54
2.7
47.67
2.3
55.69
1.9
26500
30000
34400
36500
26900
30650
34450
1.5 - 90S
27900
31800
35700
39800
44900
50000
30600
35200
40400
46000
51700
2 - 90L
12300
13700
15400
17800
19800
22600
N.A.
N.A.
N.A.
37000
42400
47600
53000
59800
66700
13800
15800
17600
19800
22750
N.A.
N.A.
N.A.
36180
40800
47000
53900
61300
68900
3 - 100L
17900
20200
22600
25800
29000
33000
37200
41600
48000
54700
61400
70000
20800
23600
26400
29800
34100
37600
42400
48700
54200
61300
70400
81300
5 - 100L
20000
22900
26200
29500
33000
37200
42900
47500
54500
61400
68600
78800
20300
24100
27160
30600
34700
39400
44000
49600
56900
62700
70700
81000
90400
102200
117400
84000
97700
116000
135000
22900
25860
29100
30500
36200
40740
45900
52000
59100
66130
74500
85300
94000
106000
121700
48800
56800
66300
74200
86400
101000
114000
126000
146000
175000
203000
42800
45400
49400
55300
65100
75800
88500
99000
115000
135000
153000
168000
195000
63400
67400
73300
82000
96300
112000
130000
145000
170000
200000
84500
89900
97700
109000
128000
150000
173000
193000
227000
POWERED ACTUATORS
Ball Screw Actuators - Performance Specifications
Lifting
Actuator Actuator Reducer Reducer Speed
Model
Ratio
Model
Ratio (in/min)
5
14.4
7.5
9.6
10
7.2
15
4.8
2 Ton BS
6:1
31
20
3.6
25
2.9
30
2.4
40
1.8
5
57.5
7.5
38.3
2 Ton BS
6:1
31
10
28.8
High Lead
15
19.2
20
14.4
5
23.7
7.5
15.8
10
11.9
15
7.9
3 Ton BS
6:1
31
20
5.9
25
4.7
30
4.0
40
3.0
5
27.2
7.5
18.2
10
13.6
15
9.1
5 Ton BS
6:1
50
20
6.8
25
5.5
30
4.5
40
3.4
5
57.4
5 Ton BS
6:1
50
7.5
38.4
High Lead
10
28.7
5
20.4
7.5
13.6
10
10.2
15
6.8
10 Ton BS
8:1
63
20
5.1
25
4.1
30
3.4
40
2.6
5
43.0
10 Ton BS
8:1
63
7.5
28.7
High Lead
10
21.5
5
21.6
7.5
14.4
10
10.8
15
7.2
20 Ton BS
8:1
75
20
5.4
25
4.3
30
3.6
40
2.7
20 Ton BS
5
43.1
8:1
75
High Lead
7.5
28.7
1/3 - 56C
4650
6680
8500
11500
14400
17000
17700
21400
1300
1880
2400
3200
4000
3100
4500
5700
7700
9650
11500
12000
14400
3000
4400
5740
7950
10200
12300
13300
16400
1330
1930
2520
3680
5400
7000
9900
12750
15400
16900
20950
1575
2300
2990
3400
5040
6650
9400
12100
15100
15600
20500
1/2 - 56C
6970
10000
12750
17300
21600
3/4 - 56C
10460
15000
19000
1 - 56C
13950
1960
2800
3600
4800
6000
4700
6750
8620
11600
14600
2940
4200
5390
3900
5600
7000
10100
12900
9400
13500
6800
9900
12900
17900
23000
27700
29900
36900
3000
4350
5670
8300
12200
15800
22300
28700
34700
38000
47100
3550
5220
6800
7700
11300
14900
21100
27400
34100
35000
46200
3850
3850
9100
13200
17200
23900
30600
37000
39900
13600
19800
25800
35800
18200
27300*
26400
34500
*Note: Model 50 reducer
requires 140 Frame motor
for 3HP application.
4000
5800
7560
11000
16200
21100
29800
38200
46300
50750
62800
4730
6960
9060
10300
15100
19900
28200
36500
45500
46700
61600
5150
5150
6000
8700
11300
16500
24300
31700
44700
57400
69500
76000
8000
11600
15100
22100
32500
42300
59500
76500
12000*
17400*
33100
48700
63400
89000
55200
81000
7100
10400
13600
15500
22700
29900
42300
54800
68200
70000
92400
7750
7750
9470
13900
18100
20600
30300
39900
56400
73100
91000
93400
123000
10300
10300
14200
20800
27200
30900
45400
59800
84500
109600
23600
34800
4550
6600
8600
11950
15300
18500
19900
24600
2000
2900
3780
5500
8100
10570
14900
19100
23100
25400
31400
2370
3480
4530
5150
7570
9970
14100
18200
22750
23400
30800
2575
2575
15450
15450
51500
75700
99700
140900
77300
113000
25750
25750
38650
38650
POWERED ACTUATORS
Ball Screw Actuators - Performance Specifications
Actuator
Model
Actuator
Ratio
Reducer
Model
25 Ton BS
10.33:1
92372
50 Ton BS
10.33:1
92672
Reducer
Ratio
5.30
5.97
6.49
7.32
8.29
9.47
10.84
11.39
13.01
14.65
17.06
19.21
21.95
24.33
27.41
31.32
33.80
38.62
43.52
49.73
55.00
4.85
5.46
5.92
6.78
7.73
8.71
9.78
11.02
12.64
14.08
16.08
18.08
20.37
23.28
26.55
29.91
34.17
37.32
42.04
48.03
51.86
Lifting
Speed
(in/min)
20.1
17.9
16.4
14.6
12.9
11.3
9.8
9.4
8.2
7.3
6.3
5.6
4.9
4.4
3.9
3.4
3.2
2.8
2.5
2.1
1.9
33.4
29.6
27.3
23.9
20.9
18.6
16.5
14.7
12.8
11.5
10.1
9.0
7.9
7.0
6.1
5.4
4.7
4.3
3.8
3.4
3.1
.50 - 71L
37500
42300
47700
54700
61700
.75 - 80S
40800
46100
52000
56300
64900
73400
84000
Charts show available ratios and motors for closecoupled, IEC frame motors. Gear reducers with
flange for NEMA C-face motor also available.
Fitting of C-face motor will increase length of
reducer-motor combination.
65200
73600
84500
89700
68400
78000
87700
97700
110000
122700
30200
33800
37800
43800
48700
55500
N.A.
N.A.
N.A.
90900
104000
117000
130000
147000
163700
43800
49500
55500
63500
71200
81300
91300
102000
118000
134000
151000
172000
5 - 100L
59000
66000
71800
81000
91700
105000
120000
126000
49000
56300
64300
72400
81300
91300
105400
116700
134000
150000
168500
193500
7.5 -132S
60000
67600
73200
84000
96000
108000
121500
136700
156900
175000
POWERED ACTUATORS
Continuous Duty Actuators - Performance Specifications
Actuator
Model
Actuator
Ratio
6:1
Reducer
Model
31
8:1
63
8:1
63
10.67:1
75
10.67:1
75
7511
(3500lbs
Max)
7515
(12000
lbs max)
75151
High Lead
(5500lb)
7522 (27000
lbs Max)
75221
High Lead
(13500lb)
Reducer
Ratio
5
7.5
10
15
20
5
7.5
10
15
20
5
7.5
10
5
7.5
10
15
20
5
7.5
10
Lifting
Speed
(in/min)
14.4
9.6
7.2
4.8
3.6
20.4
13.6
10.2
6.8
5.1
43.0
28.7
21.5
27.2
18.2
13.6
9.1
6.8
57.4
38.4
28.7
Does your application require mounting the limit switch or encoder on the reducer to allow another component to
be mounted to the actuators other side? No problem! Call our Customer Service team for assistance.
POWERED ACTUATORS
Motorized Actuator - Dimensions
A
Actuator
Capacity
Reducer
Model
(tons)
2
3
31
40
50
10
63
15
75
20
75
25
92672
35
92772
50
9042
Motor
Frame
56C
56C
140TC
56C
140TC
56C
140TC
180TC
56-140TC
180TC
56-140TC
180TC
80
90-100
132
80
90-100
132
100-160
(in)
6.75
6.75
6.75
6.25
6.25
7.59
7.59
7.59
7.40
7.40
7.68
7.68
7.40
7.40
7.40
11.49
11.49
11.49
11.64
(in)
1.22
1.57
1.57
1.97
1.97
2.48
2.48
2.48
2.95
2.95
2.95
2.95
2.68
2.68
2.68
2.87
2.87
2.87
1.42 Below
(in)
.17 Above
.22 Below
.22 Below
.11 Below
.11 Below
.59 Below
.59 Below
.59 Below
.40 Below
.40 Below
.14 Below
.14 Below
.40 Above
.40 Above
.40 Above
.92 Below
.92 Below
.92 Below
3.80 Below
(in)
4.14
4.17
4.64
4.26
4.73
4.85
5.32
6.45
6.09
6.96
6.09
6.96
7.08
7.63
7.95
7.95
8.50
9.09
9.72
Motor
HP
0.25
0.33
0.50
0.75
1
1.5
2
3
5
7.5
10
0.25
0.33
0.50
0.75
1
1.5
2
3
5
7.5
10
15
20
Motor without
Brake
Frame
56C
56C
56C
56C
56C
140TC
140TC
180TC
180TC
210TC
210TC
63L
71S
71L
80S
80L
90S
90L
100L
100L
132S
132M
160M
160L
E (in)
7.50
7.50
8.00
8.75
9.25
9.75
10.75
11.37
11.87
16.50
22.87
7.56
8.43
8.43
9.29
9.29
10.87
10.87
12.05
12.05
12.83
16.41
18.83
18.83
F (in)
7.16
7.16
7.16
7.16
7.16
7.16
7.16
9.22
9.22
10.81
10.81
5.12
5.71
5.71
6.50
6.50
7.20
7.20
7.91
7.91
8.98
10.47
12.60
12.60
F (in)
7.16
7.16
7.16
7.16
7.16
7.16
7.16
9.22
9.22
10.81
10.81
5.12
5.71
5.71
6.50
6.50
7.20
7.20
7.91
7.91
8.98
10.47
12.60
12.60
NOTES:
1. Motors in shaded portion of table are close-coupled, IEC frame, standard on 25 to 50 ton actuators with reducers.
NEMA C-face motors can be fitted to 25-50 ton units, with some increase in length. IEC frame motors can also be fitted to all other
reducers, to reduce motor envelope size.
2. Dimensions for NEMA C-face motors are typical for 1725 rpm, 3-phase, TEFC motors. Dimensions may vary somewhat depending on
manufacturer.
POWERED ACTUATORS
Reducer Positions 2-20 Tons
L1
L3
L2
R1
L4
R3
R2
R4
L2
L3
L1
L4
R2
R1
R3
R4
POWERED ACTUATORS
Actuator Motors
Duff-Norton can competitively supply motors for any application from suppliers such as Baldor, Nord, US Electric,
Leeson, and more.
Motors can be directly mounted to most Duff-Norton actuators using C-face adapters, directly mounted via speed
reducers, or remotely mounted with shafting and couplings. IEC, servo, hydraulic, and air motors can also be supplied upon request.
POWERED ACTUATORS
C-Face Motor Driven
Motor Frame Sizes
Motor RPM
Motor HP
1/2
3/4
1
1 1/2
2
3
5
1725
56C
56C, 143C
56C, 143C
56C, 143C
56C, 143C
182C
182C
1140
56C
56C, 143C
56C, 143C
182C
184C
Performance Specifications
7511
7515
75151 HL
7522
Worm
Gear
Ratio
6:1
12:1
24:1
25:1
6:1
12:1
24:1
25:1
6:1
12:1
24:1
25:1
8:1
24:1
25:1
8:1
24:1
25:1
8:1
24:1
25:1
10 2/3:1
32:1
32:1
10 2/3:1
32:1
32:1
6:1
24:1
12:1
6:1
24:1
12:1
6:1
24:1
12:1
6:1
24:1
12:1
6:1
24:1
12:1
8:1
24:1
8:1
24:1
8:1
24:1
8:1
24:1
10 2/3:1
32:1
6:1
8:1
8:1
10 2/3:1
75221 HL
10 2/3:1
Actuator
Capacity
2 Ton MS
3 Ton MS
5 Ton MS
10 Ton MS
15 Ton MS
20 Ton MS
25 Ton MS
35 Ton MS
2 Ton BS
2 Ton BS
High Lead
3 Ton BS
5 Ton BS
5 Ton BS
High Lead
10 Ton BS
10 Ton BS
High Lead
20 Ton BS
20 Ton BS
High Lead
25 Ton BS
106.9
1/2
1/2
3/4
3/4
1725
450
740
1150
1200
480
780
1110
1160
300
450
480
1270
2720
2220
180
450
320
740
1730
1230
380
1000
590
170
370
650
500
-
1140
770
1260
1970
2060
830
1320
1890
1980
390
640
980
1040
190
370
400
150
260
340
2050
4390
3580
400
980
680
1260
2950
2110
810
2140
1270
140
380
250
720
1520
180
370
1100
1080
90
-
1725
760
1250
2040
820
1320
1880
1970
380
640
970
1030
190
360
400
140
260
330
2040
3550
400
680
1250
2090
810
2120
1260
140
370
250
710
1500
170
360
1100
1070
80
-
1140
1240
2040
3320
1340
2140
3060
3200
690
1160
1750
1860
560
1090
1180
440
770
1000
240
420
480
3210
720
1220
2040
3400
1460
3840
2270
430
1110
740
1530
3210
530
1090
40
100
40
80
1780
1940
260
50
70
70
540
1725
2330
2510
1400
2340
1420
1100
940
730
1170
1090
390
650
760
5870
1450
3830
2950
4590
1080
1850
3450
1330
2000
660
1800
3680
3350
3910
660
2270
1140
3600
3880
2240
3720
2420
1880
1760
1570
2520
2350
1030
1740
2050
8990
2320
5920
4690
7300
1840
3160
5700
2270
4250
1770
3870
7890
5180
6230
1130
4870
1725
2220
2410
1870
1750
1560
1020
4660
1830
5600
2250
4200
1750
3840
6190
1120
4830
1725
4380
3400
3370
3210
2300
10000
4100
8600
3920
7910
10740
2040
9950
380
1020
1010
2260
POWERED ACTUATORS
C-Face Motor Driven
Dimensions
Capacity
10 Ton MS & BS
15 Ton MS
20 Ton MS & BS
25 Ton MS & BS
35 Ton MS
7511
7515
7522
(+.001/-.000)
56C
143TC,145TC
56C
143TC,145TC
56C
143TC,145TC
182TC, 184TC
56C
143TC,145TC
182TC, 184TC
56C
143TC,145TC
182TC, 184TC
56C
143TC,145TC
182TC, 184TC
56C
143TC,145TC
182TC, 184TC
56C
143TC,145TC
182TC, 184TC
56C
143TC,145TC
56C
143TC,145TC
182TC, 184TC
56C
143TC,145TC
182TC, 184TC
.625
.875
.625
.875
.625
.875
1.125
.625
.875
1.125
.625
.875
1.125
.625
.875
1.125
.625
.625
1.125
.625
.875
1.125
.625
.875
.625
.875
1.125
.625
.875
1.125
6.75
6.75
6.75
6.75
6.75
6.75
9.00
6.75
6.75
9.00
6.75
6.75
9.00
6.75
6.75
9.00
6.75
6.75
9.00
6.75
6.75
9.00
6.75
6.75
6.75
6.75
9.00
6.75
6.75
9.00
6.16
6.16
6.17
6.17
7.12
7.12
7.95
8.13
8.13
8.97
8.13
8.13
8.97
8.13
8.13
8.97
8.88
8.88
9.63
8.78
8.78
9.63
6.98
6.98
8.06
8.06
8.90
9.62
9.62
10.46
.50
.50
.50
.50
.62
.62
1.45
.65
.65
1.47
.70
.70
1.54
.65
.65
1.49
.74
.74
1.49
.65
.65
1.49
.50
.50
.65
.65
1.47
.65
.65
1.49
POWERED ACTUATORS
IEC Motor Driven - B-Face Motor Adaptor
B
A
F
C+D
Dimensions
Capacity
25kN - G9002
50kN - G9005
100kN - G9010
150kN - G9015
200kN - G9020
300kN - G9030
A
Flange
O.D.
B
Flange
Length**
C
Mounting
Holes B.C.
D
Mounting
Holes Dia.
E
Mounting
Hole Depth
F
Counter
Bore Dia.
G9002 - 63B14
G9002 - 71B14
G9002 - 80B14
G9002 - 90B14
G9005 - 71B5
G9005 - 80B5
G9005 - 90B5
G9005 - 100B14
G9005 - 112B14
G9010 - 80B5
G9010 - 90B5
G9010 - 100B14*
G9010 - 112B14*
G9015 - 80B5
G9015 - 90B5
G9015 - 100B14*
G9015 - 112B14*
G9020 - 80B5
G9020 - 90B5
G9020 - 100B14*
G9020 - 112B14*
G9030 - 80B5
G9030 - 90B5
G9030 - 100B14*
G9030 - 112B14*
90
105
120
140
160
200
200
160
160
200
200
190
190
200
200
190
190
200
200
190
190
200
200
190
190
126
133
143
153
178
178
178
181
181
203
203
213
213
203
203
213
213
213
213
223
223
257
257
267
267
75
85
100
115
130
165
165
130
130
165
165
130
130
165
165
130
130
165
165
130
130
165
165
130
130
6
7
7
9
M8 Tap
M10 Tap
M10 Tap
9
9
M10 Tap
M10 Tap
9
9
M10 Tap
M10 Tap
9
9
M10 Tap
M10 Tap
9
9
M10 Tap
M10 Tap
9
9
12.7
12.7
12.7
12.7
12.4
12.4
12.4
15.7
15.7
12.2
12.2
10.0
10.0
12.2
12.2
10.0
10.0
20.1
20.1
10.0
10.0
20.1
20.1
10.0
10.0
60
70
80
95
110
130
130
110
110
130
130
110
110
130
130
110
110
130
130
110
110
130
130
110
110
Note: All dimensions are shown in millimeters. All couplings are purchased separately from the motor flange kit.
*Use an adapter plate mounted to the G9010-80B5, G9015-80B5, G9020-80B5 and G9030-80B5 Flanges respectively.*
*Adapter plates should be mounted to the motor, and then to the motor flange*
**Mounts to the jacks casting, and replaces the worm cover**
POWERED ACTUATORS
IEC Motor Driven - B-Face Motor Adaptor
Please provide the following information when ordering:
Motor horsepower
Actuator model
Motor frame size
Worm gear ratio
Left or right motor adaptor position
With or without anti-backlash feature
Other special requirements
(machine screw actuators)
Speed
(mm/min)
Actuator
Capacity
25 kN
50 kN
100 kN
150 kN
200 kN
300 kN
0.12
0.18
0.25
0.37
0.55
0.75
1.10
1.50
2.20
3.70
1450
1450
1450
1450
1450
5600
3420
7340
2330
4390
2140
4050
1130
2140
8550
5490
11780
4340
8170
3990
7540
2830
5340
11920
7860
16860
6630
6110
4770
12000
10640
9810
8160
19240
17730
15420
950
1590
2530
4230
5300
11220
MOTOR RPM @ 50 Hz
RPM
Worm Gear
Ratio
1450
1450
1450
1450
1450
1450
6:1
12:1
24:1
6:1
12:1
24:1
8:1
24:1
8:1
24:1
8:1
24:1
1450
725
362.5
2175
1087.5
543.75
2175
725
2175
725
2175
725
290
650
470
800
1780
1270
1380
3090
2210
460
990
720
2400
5340
3830
1170
2510
1830
3910
8710
2230
4800
3500
1180
2230
1090
2060
170
320
10 2/3:1
32:1
2175
725
Ratings with N.A. in their cells have either exceeded the B-face flange frame size, or the single screw jack kilo-watt rating. In no case should any
screw jack be loaded or have a power supply beyond its rating or damage will likely result.
Speed
(mm/min)
Actuator
Capacity
25 kN
50 kN
100 kN
150 kN
200 kN
300 kN
0.12
0.18
0.25
0.37
0.55
0.75
1.10
1.50
2.20
3.70
1700
1700
1700
1700
1700
4670
2760
5940
1700
3200
1560
2950
600
1140
7180
4530
9730
3410
6430
3140
5920
2050
3860
10060
6550
14060
5360
4940
3700
10080
8790
8100
6590
17650
16120
14860
12780
310
520
1660
4020
9070
2770
MOTOR RPM @ 60 Hz
RPM
Worm Gear
Ratio
1700
1700
1700
1700
1700
1700
6:1
12:1
24:1
6:1
12:1
24:1
8:1
24:1
8:1
24:1
8:1
24:1
1700
850
425
2550
1275
637.5
2550
850
2550
850
2550
850
140
320
230
570
1280
920
1080
2400
1720
240
520
380
1940
4320
3100
850
1820
1330
3230
7200
1760
3770
2750
720
1360
660
1250
10 2/3:1
32:1
2550
850
Ratings with N.A. in their cells have either exceeded the B-face flange frame size, or the single screw jack kilo-watt rating. In no case should any
screw jack be loaded or have a power supply beyond its rating or damage will likely result.
CAUTION: When direct coupling a motor to an actuator, it is necessary to match motor horsepower to actuator load. Lifting speeds and
maximum actuator load capacities for actuators with various motor horsepowers are shown in the tables above. It is important that motors do not
exceed the maximum horsepowers shown.
CAUTION: Standard ratio machine screw actuators are not always self locking and require motors with brakes. Optional ratio machine screw
actuators are usually self-locking and do not require brakes. However, if self-locking is absolutely necessary, a motor brake or other restraining
device should be considered.
119
POWERED ACTUATORS
Actuator Hand Wheels
The Duff-Norton hand wheel is for actuator customers who may require precise positioning, or may have loads
which do not require motorized power to adjust.
Note: Hand wheels are not recommended for use with ball
screw actuators as they contain no braking system. Also,
for models with 12:1 ratios and lower, an additional locking mechanism to prevent backdriving is recommended.
The table below presents dimensional information for all Duff-Norton Hand Wheels. To properly select the best
hand wheel for your application, please review the provided information, or contact our customer service team.
Model #
Capacity
HW04-.375
1/4 & 1/2 Ton MS & BS
HW06-.375
1/4 & 1/2 Ton MS & BS
HW04-.500
1 & 2 Ton MS & BS
HW06-.500
1 & 2 Ton MS & BS
HW04-.625
3 Ton MS & BS
HW06-.625
3 Ton MS & BS
HW06-.750
5 Ton MS & BS
HW08-.750
5 Ton MS & BS
HW10-.750
5 Ton MS & BS
HW08-1.00
10-20 Ton MS & BS
HW10-1.00
10-20 Ton MS & BS
HW12-1.00
10-20 Ton MS & BS
*From the end of the handle to the end of the hub*
Dia.
4"
6"
4"
6"
4"
6"
6"
8"
10"
8"
10"
12"
Width*
3 3/8"
4"
3 3/8"
4"
3 3/8"
4"
4"
6 3/16"
5 3/4"
6 3/16"
5 3/4"
6 1/2"
Bore
Size
0.375
0.375
0.500
0.500
0.625
0.625
0.750
0.750
0.750
1.000
1.000
1.000
Keyway
Size
1/8 x 1/16 x 1
1/8 x 1/16 x 1
1/8 x 1/16 x 1
1/8 x 1/16 x 1
3/16 x 3/32 x 1
3/16 x 3/32 x 1
3/16 x 3/32 x 1 1/4
3/16 x 3/32 x 1 1/4
3/16 x 3/32 x 1 1/4
1/4 x 1/8 x 1 1/2
1/4 x 1/8 x 1 1/2
1/4 x 1/8 x 1 1/2
ACTUATOR CONTROLS
Duff-Norton, the market leader in Screw Jack technology has been supplying customers worldwide with lifting devices for over 125 years and with customized control systems to enable precision movement for over 17 years.
ACTUATOR CONTROLS
Features & Benefits
Duff-Norton designs and manufactures a wide range of electronic logic control systems that are optimized for linear
motion control and general automation applications. Duff-Norton can provide you with a complete turnkey solution to
meet all your custom solution requirements. Our control panels are installed by our factory trained technical personnel
therefore there is no need for customers to spend time fidgeting with wires or adding components.
Duff-Norton control panels can be designed around 3 hp to 200 hp systems with ratings from 200 V to 575 V
Benefits
Standard Feature
Standard Benefits
Software:
PLC Panels
Position synchronization
Position control
ACTUATOR CONTROLS
Duff-Norton Offers Turnkey Solutions for Applications in the Following Markets
Motion Solutions
Duff-Norton is a designer and manufacturer of complete turnkey
solutions for a variety of industries such as aluminum, steel, agriculture, construction, communications, energy, food & beverage
and industrial machinery. If you want to tilt an object fixed at on
end, lift, lower, roll, slide, open or close and object or if you have an
application that requires periodic adjustment, Duff-Norton can use
linear actuators and electrical cylinders to design a custom solution
thats tailored to your specific needs.
ACTUATOR CONTROLS
Rotary Limit Switches
Screw
Traveling Nuts
Nut Guide
Precision
Input Shaft
Gear
Available in two control voltage ratings: 250 or 480, and in three gear ratios.
Can be used in applications where there is a need to control equipment that rotates and/or reverses.
Sturdy and compact. Constructed of corrosion-resistant materials, with housing of black anodized aluminum. Meets
NEMA-4 water tightness requirements.
Simple to adjust. Two switches, one for up/stop and one for down/stop, are activated by the adjustable limit-switch nuts
which travel laterally when the internal screw is rotated through gear reduction.
Operating temperature range -20 to + 150F.
Lifetime lubricated.
Can be mounted on right or left extension of actuator worm shaft in any of four quadrants.
Optional 4-position limit switch available. Consult factory for dimensions.
To ensure that limit switch has sufficient travel capability for the actuator unit, use the following formula:
Maximum raise of actuator model in inches =
Note: For water-tight connection, use a weather-tight connector and sealant around threads. Limit switches will be damaged if overtraveled.
For shipping purposes, the 1/2 NPT hole is closed with a plastic plug which is not water tight.
ACTUATOR CONTROLS
Rotary Limit Switches
AC
DC
250
Max. Amps
AC
DC
15
125
480
.50
15
250
.25
Max.
Max.
Max. Allow-
Notch
Worm Rev.
1095
2190
4380
750
1500
3000
Rise
1095/TPI
2190/TPI
4380/TPI
750/TPI
1500/TPI
3000/TPI
able Drift
24/TPI
48/TPI
96/TPI
29/TPI
57/TPI
115/TPI
Adjustment
1/TPI
2/TPI
4/TPI
1/TPI
2/TPI
4/TPI
Switch Position
ACTUATOR CONTROLS
Rotary Limit Switches
Limit Switch Field Installation Dimensions
Mounting
Worm
Dimensions
6 3/4
6 3/4
7 3/4
8 3/4
8 3/4
10 1/4
14 1/4
15 1/4
14 3/4
14 3/4
Shaft Dia.
.500
.500
.750
1.000
1.000
1.375
1.500
1.750
1.750
1.875
ACTUATOR CONTROLS
Potentiometer / Transducer
The Duff-Norton SKA6205 Series Position Feedback Potentiometer/Transducer is designed to mount on the end of
any SKA6000T limit switch. Its active component is a precision potentiometer which may be used as voltage divider
to provide a feedback voltage that is proportional to actuator position.
Max. Turns
Potentiometer
Worm Shaft
30
50
60
100
200
400
Potentiometer
Limit Switch
ACTUATOR CONTROLS
Digital Position Indicator for Duff-Norton Potentiometers
The Duff-Norton model SK6300-4K Digital Position Indicator processes a feedback signal from a the SKA6205
series potentiometers to provide position readout with user selectable scaling factor. By running the actuator to two
positions in its stroke and keying in the desired readout at each point, the indicator automatically scales the input
signal to provide linear readout over the full travel of the actuator.
The SK6300-4K has a universal, 85-250 VAC power input and generates a regulated 24 VDC excitation signal to the
potentiometer. The SK6300-4K operates seamlessly with any potentiometer equipped Duff-Norton actuator.
ACTUATOR CONTROLS
Worm Shaft Encoder
The Duff-Norton Digital Encoder and Digital Display is a more advanced way to
determine an actuators position.
A digital encoder can be used to provide an extremely precise position signal to
devices such as the Duff-Norton SK10006-35 digital display or 3rd party PLCs.
Duff-Norton uses two styles of incremental encoders, with the type used depending on the layout of the actuator. When one end of the actuator worm shaft
is accessible, a Hollow Bore style of encoder is used, mounted on the worm.
When the worm is not accessible, and the actuator is using a flange-mounted
motor, a Ring Kit style encoder can be fitted on the drive motor.
Function
Com
+VDC
A
Black
White
Brown
Red
ACTUATOR CONTROLS
Ring Kit Encoder
The Ring Kit Encoder counts motor revolutions and is mounted between the C-face motor and motor mounting
flange. This mounting allows the actuator worm opposite the motor to be available for mounting a limit switch or
driving another actuator. With 60 pulses per motor revolution, the ring kit offers a high pulse count relative to actuator
travel. A small junction box with NPT opening is attached to the ring, allowing easy, protected electrical connections.
Available for all sizes of NEMA C flanges used on Duff-Norton actuators. Additional output types available. Contact
Duff-Norton Application Engineering for specifics.
Specifications
Sensor Type........................... Bidirectional shaft speed sensor
Pulse Per Revolution............. 60 cycles each channel
Supply Voltage...................... +12 Volts DC +/-5%
Supply Current...................... 60 mA typical (115 mA maximum)
Output Drive Capability......... 250 mA per channel continuous
Maximum Load...................... 50 ohms per channel
ACTUATOR CONTROLS
Programmable Digital Position Indicator for Duff-Norton Encoders
Displays position of actuator lifting screws in increments of up to .001, depending on PPR (Accuracy is relative to
ratio and backlash. Please consult factory for details).
The Duff-Norton SK10006-35 Digital Position Indicator provides a high degree of accuracy and versatility when incorporated in machine or ball screw
actuator systems. Operating as a revolution counter,
it is ideal for use in a wide range of precision positioning applications to indicate inches or millimeters
of lifting screw travel. Two built-in relays act as limit
switches for travel limit control. Start-up/shut-off,
audio/visual warning, multiple actuator system sequencing or the initiation of subsequent operations
may also be controlled.
Electrical connections are made at the rear of the
unit to UL recognized terminal strips. Clamp-type
pressure plate terminals accept AWG-14 wire without lugs.
Five digit input scaling with 0.0000 to +/- 5.0000, programmable decimal point location and lead zero blanking.
Two adjustable up/down output limits with 0 to +/- 999999.
Non-volatile E2-PROM Memory retains all programmed information and count value in event of power interruption.
Input power requirement is 115/230 VAC, 50/60 Hz.
Can be provided with optional 4 - 20 mA current loop to provide capability of 2-way digital communication.
On-line self-test permits complete check of all functions and reset capability allows reset to zero from front panel.
Compact, die cast NEMA 4 rated front panel has six digit LED display with 0.56 high characters and negative sign (-).
Display convertible to English, metric or other units of measurement.
Field Programmable front panel functions may be locked out to prevent unauthorized adjustment.
For use in precision positioning applications with Duff-Norton 2 ton and larger machine or ball screw actuators.
ACTUATOR CONTROLS
Magnetostrictive Position Sensor
Duff-Norton offers Magnetostrictive Position Sensors for machine and ball screw actuators. These sensors offer
analog or digital outputs, and can be used for accurate position indication or with a PLC in a closed loop control
system. Magnetostrictive position sensors are non-contacting, resulting in longer life than other linear transducers or
potentiometers.
Due to the fact that the magnet senses actual screw displacement, position indication is absolute and unaffected by
gearset backlash.
Specifications
Supply Voltage +15 to 26 VDC
Non-Linearity 05% of Full Scale or to .002 in.
( 0.05 mm) whichever is greater
Repeatability 0.001% of Full Scale. or
0.0001 in. (0.002 mm) whichever
is greater
Hysteresis 0.0008 in. (0.076 mm) max.
Measuring Range U.S. Customary: 1 to 60 in. (0.1
in. increments) Metric: 50 to 1500
mm (5 mm increments)
ACTUATOR CONTROLS
Rotary Counters
The Duff-Norton Rotary Counter is for actuator customers who are looking for a more economical and easy way to
determine an actuators position. Our counters have been designed to match our most common actuator ratios. An
operator viewing the reading in the display window will know his actuators exact position because the counters
display shows stroke to the nearest 1000ths of an inch up to 99 inches of travel. Custom numeric displays are also
available.
Turns of Worm
Clockwise rotation
For 1" Raise
RC16R
16
RC24R
24
RC32R
32
RC48R
48
RC64R
64
RC96R
96
RC100R
100
Counter clockwise rotation
16
RC16L
24
RC24L
32
RC32L
48
RC48L
64
RC64L
96
RC96L
100
RC100L
Optional 1
10-100 Ton
5 Ton
2-3 Ton
Optional 2
Approx.
Numeric
2-25 Ton
Width
2"
2"
2"
2"
2"
2"
2"
2-25 Ton
2"
2"
2"
2"
2"
2"
2"
5 Ton
2-3 Ton
5-100 Tons
2-3 Ton
10-100 Ton
5 Ton
2-3 Ton
5 Ton
2-3 Ton
Note: counter models with either 24 or 96 turns will be short .002 per inch. For those models,
instead of a 1.000 reading, one would have a .998 reading.
70
30
40
6 h9
47
27
37
75
56
9
44
Model #
SK8001-6
BU10-.625
BU10-.750
BU10-1.00
Bore Size
.500"
.625"
.750"
1.00"
Capacity
2 Ton MS
3 Ton MS
5 Ton MS
10 - 20 Ton MS
1.
3.
2.
4.
Coupling Part #
MS 1/4 Ton
MS 1/2 Ton
MS 1 Ton
MS 2 Ton
MS 3 Ton
MS 5 Ton
MS 10 Ton
MS 15 Ton
MS 20 Ton
MS 25 Ton
MS 35 Ton
MS 50 Ton
SK2555-29
SK2555-29
SK2402J
SK2402J
CP03-500500
CP05-750750
CP20-10001000
CP20-10001000
CP20-10001000
CP35-13751375
CP35-13751375
CP50-15001500
Connecting
Shaft Part #
Pillow Block
Part #
AB 1/4 Ton
AB 1/2 Ton
AB 1 Ton
AB 2 Ton
AB 3 Ton
AB 5 Ton
AB 10 Ton
AB 15 Ton
AB 20 Ton
AB 25 Ton
AB 35 Ton
AB 50 Ton
Coupling Part #
Description
SK2555-29
SK2555-29
SK2402J
SK2402J
CP03-500500
CP05-750750
CP20-10001000
CP20-10001000
CP20-10001000
CP35-13751375
CP35-13751375
CP50-15001500
Shaft Part #
BS 1/2 Ton
BS 1 Ton
BS 2 Ton
BS 2 Ton*
BS 3 Ton
BS 5 Ton
BS 5 Ton*
BS 10 Ton
BS 10 Ton*
BS 20 Ton
BS 20 Ton*
BS 25 Ton
BS 50 Ton
*High Lead Option*
Coupling Part #
Description
SK2555-29
SK2402J
SK2402J
SK2402J
CP03-500500
CP05-750750
CP05-750750
CP20-10001000
CP20-10001000
CP20-10001000
CP20-10001000
CP35-13751375
CP50-15001500
Mitre Box
Part #
Mitre Box
Description
3 way
3 way
3 way
3 way
3 way
3 way
3 way
3 way
3 way
3 way
3 way
MB-19G
MB-19G
MB-20G
MB-20G
MB-20G
MB-22G
4 way
4 way
4 way
4 way
4 way
4 way
Part #
Mitre Box
Part #
Mitre Box
Description
Mitre Box
Part #
Mitre Box
Description
3 way
3 way
3 way
3 way
3 way
3 way
3 way
3 way
3 way
3 way
3 way
MB-19G
MB-19G
MB-20G
MB-20G
MB-20G
MB-22G
4 way
4 way
4 way
4 way
4 way
4 way
Mitre Box
Description
Mitre Box
Part #
Mitre Box
Description
3 way
3 way
3 way
3 way
3 way
3 way
3 way
3 way
3 way
3 way
3 way
3 way
MB-19G
MB-19G
MB-19G
MB-19G
MB-20G
MB-20G
MB-22G
4 way
4 way
4 way
4 way
4 way
4 way
4 way
SH50
PB50
MB-4
SH63
PB63
MB-4
SH100
PB100
MB-7
SH100
PB100
MB-16
SH100
PB100
MB-16
SH150
PB150
MB-19
SH163
PB168
MB-19
SH200
PB200
MB-20
SH225
PB225
MB-20
SH225
PB244?
MB-20
SH250
MB-22
**Please contact our customer service team**
Ball
Screw Power Transmission
Components
Bore Size &
Actuator
Connecting
Model
Mitre Box
Description
SH50
PB50
MB-4
SH63
PB63
MB-4
SH75
PB75
MB-7
SH100
PB100
MB-16
SH100
PB100
MB-16
SH150
PB150
MB-19
SH163
PB168
MB-19
SH200
PB200
MB-20
SH200
PB200
MB-20
SH225
PB225
MB-20
SH250
MB-22
**Please contact our customer service team**
Anti-Backlash
Power Transmission
Components
Bore Size &
Actuator
Connecting
Pillow Block
Model
Mitre Box
Part #
Shaft Part #
Pillow Block
Part #
Mitre Box
Part #
SH50
PB50
MB-4
SH63
PB63
MB-4
SH100
PB100
MB-16
SH100
PB100
MB-16
SH100
PB100
MB-16
SH125
PB125
MB-19
SH150
PB150
MB-19
SH125
PB125
MB-19
SH163
PB168
MB-19
SH163
PB168
MB-20
SH200
PB200
MB-20
SH163
PB168
MB-22
**Please contact our customer service team**
NOTE
All selections are based on the actuators worm input torque at full load. As the application and load changes,
the power transmission components best suited for the application may change as well. In particular, connecting shaft sizes could change depending on the shaft length required, which may also result in changes to the
pillow blocks and couplings.
www.duffnorton.com Ph: (800) 477-5002 Fax: (704) 588-1994
135
Coupling Part #
SK2402J
CP03-500500
CP05-750750
CP20-10001000
CP20-10001000
CP20-10001000
CP35-13751375
CP35-13751375
CP50-15001500
1/2"Bore - Jaw
1/2" Bore - Chain
3/4" Bore - Chain
1" Bore - Chain
1" Bore - Chain
1" Bore - Chain
1 3/8" Bore - Chain
1 3/8" Bore - Chain
1 1/2" Bore - Chain
Connecting
Shaft Part #
Mitre Box
Part #
SH100
PB100
SH100
PB100
SH150
PB150
SH150
PB150
SH175
PB175
SH175
PB175
SH225
PB225
SH225
PB225
**Please contact our customer service team**
Mitre Box
Description
Mitre Box
Part #
Mitre Box
Description
MB-7
MB-16
MB-16
MB-19
MB-20
MB-20
MB-19
MB-22
3 way
3 way
3 way
3 way
3 way
3 way
3 way
3 way
MB-19G
MB-20G
MB-20G
MB-19G
MB-22G
4 way
4 way
4 way
4 way
4 way
Coupling Part #
Connecting
Shaft Part #
Mitre Box
Part #
Mitre Box
Description
Mitre Box
Part #
Mitre Box
Description
CD 7511
CD7515
CD 75151*
CD 7522
CD 75221*
*High Lead Option*
SK2402J
CP20-10001000
CP20-10001000
CP20-10001000
CP20-10001000
SH100
SH100
SH100
SH125
SH150
PB100
PB100
PB100
PB125
PB150
MB-7
MB-16
MB-16
MB-19
MB-19
3 way
3 way
3 way
3 way
3 way
MB-19G
MB-19G
4 way
4 way
NOTE
All selections are based on the actuators worm input torque at full load. As the application and load changes,
the power transmission components best suited for the application may change as well. In particular, connecting shaft sizes could change depending on the shaft length required, which may also result in changes to the
pillow blocks and couplings.
Type
3 Way
3 Way
3 Way
3 Way
4 Way
3 Way
4 Way
3 Way
4 Way
Shaft Diameter
.375"
.75"
.625"
1.0"
1.0"
1.25"
1.25"
1.375"
1.375"
Our mitre boxes feature a compact design, which eliminates the need for an extended hub. With this design feature the bevel gear is supported by tapered roller bearings on both sides. The result is a higher horsepower rating,
increased service-life, improved lubrication, and more flexible mounting compared to other brands.
Torque
MB-16
344
0.625
1.219
1.688
4.875
0.187
3.188
1.594
7.250
3.625
Model
Torque
MB-4
MB-8
23
97
0.375
0.750
0.625
1.375
0.781
1.563
1.313
3.000
1.313
3.000
1.375
3.000
2.750
6.000
2.156
4.563
FLAT
3/16
2.938
6.563
0.219
0.375
2.156
5.000
1.250
3.000
0.875
2.250
1.188
3.000
0.188
0.375
Model
Torque
MB-19 (G)
MB-20 (G)
MB-22 (G)
1400
3000
5000
1.000
1.250
1.375
1.396
1.840
2.170
2.000
2.500
2.938
4.250
4.500
6.000
2.125
2.250
3.000
4.250
4.500
6.000
2.125
2.250
3.000
7.000
8.000
10.625
2.750
2.875
4.125
5.500
6.500
8.250
5/16
3/8-16
-13
-13
4.125
5.625
7.500
2.062
2.813
3.750
11.000
13.000
16.500
5.500
6.500
8.250
Model
Torque
MB-16
344
0.625
1.219
1.688
4.875
0.187
3.188
1.594
7.250
3.625
Torque
MB-4
MB-8
23
97
0.375
0.750
0.625
1.375
O
0.781
1.563
1.313
3.000
1.313
3.000
1.375
3.000
2.750
6.000
2.156
4.563
FLAT
3/16
P
Model
Torque
MB-19 (G)
MB-20 (G)
MB-22 (G)
1400
3000
5000
1.000
1.250
1.375
1.396
1.840
2.170
2.000
2.500
2.938
4.250
4.500
6.000
2.125
2.250
3.000
4.250
4.500
6.000
2.125
2.250
3.000
B
K
1 1/8
H
7.000
2.750
8.000
1 3/8 2.875
10.625 4.125
3/8 SLOT
J
TYP.
(3) K
2.938
6.563
0.219
0.375
2.156
5.000
1.250
3.000
0.875
2.250
1.188
3.000
0.188
0.375
5.500
6.500
8.250
5/16
3/8-16
-13
-13
4.125
5.625
7.500
2.062
2.813
3.750
6.56
J
1 3/8
1 3/8
3 1/8
2 7/8
11.000 5.500
13.000 6.500
1 9/16
16.500 8.250
O
P
I
Model
N
Torque
MB-16
344
0.625
1.219
MModel
MB-4
MB-8
H
D
1.688
4.875
0.187
3.188
1.594
7.250
3.625
E FF .
L ENGTH
Torque
23
97
0.375
0.750
0.625
1.375
0.781
1.563
1.313
3.000
1.313
3.000
1.375
3.000
2.750
6.000
2.156
4.563
FLAT
3/16
2.938 K 0.219
6.563
0.375
2.156
5.000
1.250
3.000
C
N
L
0.875
2.250
B
J
1.188
3.000
0.188
0.375
Model
Torque
MB-19 (G)
MB-20 (G)
MB-22 (G)
1400
3000
5000
1.000
1.250
1.375
1.396
1.840
2.170
2.000
2.500
2.938
4.250
4.500
6.000
2.125
2.250
3.000
4.250
4.500
6.000
2.125
2.250
3.000
7.000
8.000
10.625
2.750
2.875
4.125
5.500
6.500
8.250
5/16
3/8-16
-13
-13
4.125
5.625
7.500
2.062
2.813
3.750
11.000
13.000
16.500
5.500
6.500
8.250
Chain Couplings:
Integrate well with Duff-Norton mid and larger capacity actuators
High torque capacities
Standard ANSI dimensions, straight bore diameters
Common bore diameters may be custom ordered
Special bore diameters may be custom ordered
Long service lives
Easy fit onto the actuators worm shaft
Allows for incremental system adjustments
Standard Maximum
Bore***
Bore
.500"
.875"
.625"
.875"
.750"
1.25"
1.000"
1.687"
1.375"
2.000"
1.500"
2.437"
Coupling
Key Broach
Dimensions
.125" x .63"
.125" x .63"
.1875" x .093"
.25" x .125"
.313" x .156"
.375" x .1875"
A*
4.00"
4.00"
4.00"
5.13"
5.13"
6.38"
B
2.53"
2.53"
2.53"
3.25"
3.75"
4.23"
C
1.41"
1.41"
1.41"
2.50"
2.97"
3.50"
D
1.13"
1.13"
1.13"
1.44"
1.69"
1.88"
E
.28"
.28"
.28"
.38"
.38"
.47"
Act. Torque
@ Load**
132
181
495
2255
4400
8250
Coupling
Torque
1354
1354
1354
4614
5969
10899
Cover
Misalignment (Max)
Parallel
Angular
.015
1/2 deg.
.015
1/2 deg.
.015
1/2 deg.
.015
1/2 deg.
.015
1/2 deg.
.015
1/2 deg.
Jaw Couplings:
Integrate well with Duff-Norton smaller capacity actuators
Do not require lubrication
Our Hytrel spiders provide 2 times the torque
capability vs. a standard urethane or BUNA spider
Easy fit onto the actuators worm shaft
Standard
Bore***
.375"
.375"
.626"
Maximum
Bore
.875"
.875"
.875"
Key Broach
Dimensions
None
.125" x .63"
.1875" x .0938"
A*
1 5/64
1 3/4
1 3/4
B
7/16
15/32
15/32
C
15/32
1/2
1/2
D
5/8
13/16
13/16
E
1 5/64
1 3/4
1 3/4
F
1 23/32
2 1/8
2 1/8
Coupling
Torque
50
250
250
Misalignment (Max)
Parallel
Angular
.015
1/2 deg.
.015
1/2 deg.
.015
1/2 deg.
Part #
Standard Maximum Key Broach
Flex Hub Rigid Hub Bore*** Bore*** Dimensions
A*
SK2405H
SK2404H
.0751
1.25
.1875" x .0938" 3 5/16
SK2410H
SK2409H
1.001
1.25
.25" x .125"
3 5/16
SK2425H
SK2424H
1.376
1.625
.313" x .156"
3 3/4
SK2450H
SK2449H
1.501
1.625
.375" x .1875" 3 3/4
SK2499H
SK2498H
1.751
2.125
.50" x .25"
4 3/4
B
2
2
2 17/32
2 17/32
2 9/16
C
D
E
1/8 1 1/2
2
1/8 1 1/2
2
1/8 1 13/16 2 3/8
1/8 1 13/16 2 3/8
1/8 2 1/16 3 1/4
F
H
3 1/8 2 1/8
3 1/8 2 1/8
3 3/4 2 21/32
3 3/4 2 21/32
4 1/4 2 11/16
SH50
5
1/2
0.500
0.499
1/8
1.25
SH63
5
5/8
0.625
0.624
3/16
1.25
SH75
5
3/4
0.750
0.749
3/16
1.25
SH100
5
1
1.000
0.999
1/4
1.25
SH125
6
1 1/4
1.250
1.249
1/4
1.5
SH150
7
1 1/2
1.500
1.499
3/8
1.75
SH163
7
1 5/8
1.625
1.624
3/8
1.75
SH175
7
1 3/4
1.750
1.749
3/8
2
Note: Minimum shaft length may vary depending on the specified coupling.
SH200
8
2
2.000
1.999
1/2
2
SH225
10
2 1/4
2.250
2.247
1/2
2.5
SH250
10
2 1/2
2.500
2.497
5/8
2.5
Typical
Shaft
Torque
(Inch/Lbs.)
20
40
50
80
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
1250
1500
1750
2000
2250
2500
3000
3250
3500
4000
4500
5000
6000
7000
Nominal
Shaft
Diameter*
(Inches)
0.51
0.73
0.81
0.87
0.92
1.01
1.09
1.15
1.21
1.25
1.30
1.34
1.37
1.44
1.49
1.54
1.59
1.63
1.72
1.80
1.92
1.94
2.00
2.05
2.15
2.19
2.23
2.31
2.38
2.44
2.55
2.65
Maximum**
Distance
Between
Supports
(Inches)
54.60
61.30
65.50
68.80
71.40
76.30
80.10
83.10
85.70
87.90
89.90
91.70
93.30
96.20
98.70
100.90
102.90
104.70
108.70
112.00
114.90
117.50
119.80
122.00
125.70
127.40
129.00
131.90
134.50
136.90
141.10
144.80
36
1802
2143
2372
2548
2695
2982
3204
3388
3546
3686
3811
3925
4029
4217
4383
4532
4667
4792
5067
5303
5511
5698
5869
6025
6306
6434
6554
6776
6979
7165
7499
7794
48
1014
1205
1334
1433
1516
1677
1802
1906
1995
2073
2144
2208
2266
2372
2465
2549
2625
2695
2250
2983
3100
3205
3301
3389
3547
3619
3687
3812
3926
4030
4218
4384
60
649
771
854
917
970
1074
1154
1220
1277
1327
1372
1413
1451
1518
1578
1631
1680
1725
1824
1909
1984
2051
2113
2169
2270
2316
2359
2440
2512
2579
2700
2806
72
450
536
593
637
674
746
801
847
887
921
953
981
1007
1054
1096
1133
1167
1198
1267
1326
1378
1425
1467
1506
1577
1608
1639
1694
1745
1791
1875
1949
120
162
193
213
229
243
268
288
305
319
332
343
353
363
380
394
408
420
431
456
477
496
513
528
542
568
579
590
610
628
645
675
701
132
134
159
176
190
200
222
238
252
264
274
283
292
300
314
326
337
347
356
377
394
410
424
437
448
469
479
487
504
519
533
558
580
144
113
134
148
159
168
186
200
212
222
230
238
245
252
264
274
283
292
299
317
331
344
356
367
377
394
402
410
424
436
448
469
487
156
96
114
126
136
143
159
171
180
189
196
203
209
215
225
233
241
249
255
270
282
293
303
313
321
336
343
349
361
372
382
399
415
Note: Shaded area exceeds maximum distance between supports. Additional support is required.
* Shaft diameter is based on 0.08 degrees twist per foot of length.
** Maximum distance between supports is based on a maximum allowable deflection of 0.01 inches per foot of length.
*** Maximum allowable RPMs is based on 80% of critical shaft speed.
Chain Coupling
Pillow Block
Shaft
Part #
PB50C
PB63C
PB75C
PB100C
PB125C
PB150C
PB168C
PB175C
PB200C
PB225C*
*Cast iron housing*
Diameter
1/2
5/8
3/4
1
1 1/4
1 1/2
1 11/16
1 3/4
2
2 1/4
A
1 1/16
1 1/16
1 1/4
1 5/16
1 13/16
1 15/16
2 1/16
2 1/16
2 7/16
2 11/16
B
2 1/8
2 1/8
2 1/2
2 5/8
3 19/32
3 27/32
4 1/8
4 1/8
4 27/32
5 11/32
C
.969
.969
1.142
1.339
1.843
2.063
2.260
2.260
2.705
2.949
D
2 1/4
2 1/4
2 5/8
2 25/32
3 27/32
4 3/16
4 17/32
4 17/32
5 5/16
5 13/16
E Min. E Max.
3 3/8
3 5/8
3 3/8
3 5/8
3 3/4
3 31/32
4
4 1/4
4 13/16 5 3/16
5 5/16 5 11/16
5 9/16 5 15/16
5 9/16 5 15/16
6 7/8
7 3/8
7 9/32 7 15/16
F
4 3/4
4 3/4
5 1/32
5 1/2
6 9/16
7 1/8
7 7/16
7 7/16
9 1/8
9 1/2
G
1 3/8
1 3/8
1 1/2
1 9/16
1 7/8
2 1/16
2 1/8
2 1/8
2 3/8
2 17/32
H
33/64
33/64
35/64
19/32
45/64
3/4
25/32
25/32
29/32
63/64
J
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
5/8
5/8
L
1 5/16
1 5/16
1 15/32
1 9/16
1 15/16
2 7/32
2 1/4
2 1/4
2 1/2
2 25/32
M
.626
.626
.720
.776
1.00
1.189
1.189
1.189
1.315
1.528
S
1.079
1.079
1.220
1.339
1.689
1.937
1.937
1.937
2.189
2.114
Wt. Lbs.
1.2
1.2
1.9
2.4
3.8
4.8
5.4
5.4
8.7
10.9
For more Flange Block information please see the table below
Flange Block
Rotating Screw
Actuator
Part #
FB50C
FB63C
FB75C
FB87C
FB100C
FB125C
FB150C
FB175C
FB225C*
*Cast iron housing*
Rotating Actuator
MS and BS up to 1 Ton
2 Ton MS
2 and 3 Ton BS
3 Ton MS
5 Ton MS, 5-10Ton BS
10 Ton MS
15 Ton MS
20 Ton MS & BS
25 Ton BS
Shaft Size
1/2
5/8
3/4
7/8
1
1 1/4
1 1/2
1 3/4
2 1/4
B
3
3
3 3/8
3 21/32
3 21/32
4 9/16
5 3/32
5 5/16
6 29/32
B.C.
3
3
3 5/8
3 57/64
3 57/64
5 1/8
5 43/64
5 27/32
7 31/32
C
.969
.969
1.142
1.339
1.339
1.843
2.063
2.260
2.949
D
2 3/32
2 3/32
2 3/8
2 3/4
2 3/4
3 9/16
4 1/32
4 1/4
5 5/16
E
2 1/8
2 1/8
2 1/2
2 3/4
2 3/4
3 5/8
4
4 1/8
5 5/8
H
7/16
7/16
19/32
19/32
19/32
11/16
11/16
23/32
23/32
J
3/8
3/8
3/8
7/16
7/16
1/2
1/2
1/2
5/8
L
1 7/32
1 7/32
1 15/32
1 17/32
1 17/32
1 27/32
2 1/8
2 1/8
2 43/64
M
31/32
31/32
1 5/32
1 3/16
1 3/16
1 3/8
1 17/32
1 9/16
1 57/64
S
1.079
1.079
1.220
1.399
1.399
1.689
1.937
1.937
2.114
Wt.Lbs.
1.0
1.0
1.5
1.9
1.9
4.4
5.6
6.0
11.9
Protects the lifting screw from: dust, dirt, moisture, and corrosive contaminants.
Helps maintain the proper lubrication.
Can be provided for all actuator screw end types and configurations.
Standard bellows boots are made of neoprene coated nylon with sewn construction.
Special bellows boots can be provided with a variety of materials for applications involving high temperatures, highly
corrosive atmospheres, and other special conditions.
Bellows boots can also be provided from molded materials, with internal or external guides to prevent sagging, and
with zippers for easy installation or removal.
Actuator Capacity
Actuator Capacity
Shell Cap Diameter
Shell Cap
"A"Diameter "A"
1/2 Ton BS 1/2 Ton BS
2 1/4
2 1/4
1 Ton BS
1 Ton BS
2 3/4
2 3/4
2 Ton BS
2 Ton BS
3 1/2
3 1/2
3 Ton BS
3 Ton BS
3 1/2
3 1/2
5 Ton BS
5 Ton BS
5 3/8
5 3/8
10 Ton BS 10 Ton BS
4 1/2
4 1/2
20 Ton BS 20 Ton BS
7
7
25 Ton MS 25 Ton MS
8 7/8
8 7/8
50 Ton MS 50 Ton MS
9 1/2
9 1/2
Closed Height When Optional Bellows Boots are Required on Standard Upright Actuators
Boot
O.D.
1/4 Ton MS
1/2 Ton MS
1 Ton MS
2 Ton MS
3 Ton MS
5 Ton MS
10 Ton MS
15 Ton MS
20 Ton MS
25 Ton MS
35 Ton MS
50 Ton MS
75 Ton MS
100 Ton MS
150 Ton MS
250 Ton MS
4 1/4"
4 1/4"
6"
7 3/4"
7 3/4"
7 3/4"
9"
9"
9"
10 3/4"
11"
14 1/2"
16 1/2"
11 1/4"
12 1/4"
16"
Raise up to 12"
A
B
C
4
4
4 1/4
4
4
4 1/2
4 1/2
5
5 3/8
5 1/4 6 1/2 7 1/4
5 3/4 6 1/2 6 1/2
7
7
8
7 1/4 8 1/2 9 3/4
8
8 1/2 9 3/4
9 1/4
10 11 1/2
11
12 13 3/4
12
13
15
13
15 17 1/2
17 1/2 19 21 1/2
24
24
25
24
24
25
30
13
16 18 1/2
17 1/2 19 21 1/2
24
24
25
24
24
25
30
4 1/4
5 1/2
5 3/4
6 5/8
7
7 1/4
8
9 1/4
11
12
13
17 1/2
24
24
30
4 5/8
5 3/4
7 1/2
7
8 1/2
9 1/2
10
11
13 1/4
13
16
19
24
24
4 1/2
6 1/4
8 1/4
7
9 1/2
10 3/4
11 1/4
12 1/2
15
15
18 1/2
21 1/2
25
25
5 3/4
6 5/8
8
8 1/2
9
10 1/2
12
12
14
17 1/2
24
24
30 1/2
7 1/2
7 7/8
8 1/2
9 1/2
10
12
13 1/4
13 3/4
16
19
24
24
8 1/4
8
9 1/2
10 3/4
11 1/4
13 1/2
15
15 3/4
18 1/2
21 1/2
25
25
6 1/4
7 7/8
8
8 1/2
9
10 1/2
12
12
14
17 1/2
24 1/2
24 1/2
30 1/2
8 1/2
7 7/8
10
9 1/2
10
12
14 1/2
13 3/4
17
19
24 1/2
24 3/8
9 1/4
8
11
10 3/4
11 1/4
13 1/2
16 1/4
15 3/4
19 1/2
21 1/2
25 1/2
25 3/8
9
9 1/2
11
11 1/2
13
12 7/8
15
18 1/2
25
25
31 1/2
10
10 1/2
12
13
15 3/4
14 3/4
18
20
25 1/2
25 1/8
11
11 3/4
12 1/4
14 1/2
17 1/2
16 3/4
20 1/2
20 1/2
26 1/2
26 1/8
11 1/2
12
13 1/2
15
14 3/4
17
20 1/2
27
27
32
12 1/2
13
15
16 3/4
16 1/2
19
22
27 1/2
26 5/8
13 3/4
14 1/4
16 1/2
18 1/2
18 1/2
21 1/2
24 1/2
28 1/2
27 5/8
Boot
O.D.
1/2 Ton BS
1 Ton BS
2 Ton BS
3 Ton BS
5 Ton BS
10 Ton BS
20 Ton BS
25 Ton BS
50 Ton BS
4 1/2"
4 1/4"
6 5/8"
6 5/8"
7 1/2"
7"
9"
11"
12"
Raise up to 12"
A
B
C
61/4
7 1/2
9 1/4
10 3/4
10 3/8
16 1/2
19 3/4
25 3/8
6 7/8
7 1/2
9 1/4
10 3/4
10 3/8
16 1/2
19 3/4
25 3/8
7 1/2
7 1/2
9 1/4
10 3/4
10 3/8
16 1/2
19 3/4
25 3/8
8 1/2
10 1/4
12 1/2
11 5/8
16 1/2
19 3/4
25 3/8
10 1/4
12 1/2
11 5/8
16 1/2
21 1/4
26 3/8
11 1/4
13 3/4
12 7/8
18 1/2
21 1/4
26 3/8
20 1/2
22 3/4
27 3/8
21 1/2
24 1/4
28 3/8
Raise up to 6"
A
B
C
2
2 3/8
2
2
2 5/8
2/18
2 1/6
3
2 5/8
2 3/8
4 3/8
3 5/8
2 3/8
3
2 3/4
3 3/16
4 3/16
3 3/16
3 1/4
5 3/4
4 1/2
3 1/4
5 1/4
4
3 1/4
5 9/16
4 1/16
3 3/8
6 3/4
5
4 1/2
7 1/2
5 1/2
4 7/8
9 5/16 6 13/16
2 3/8
6 7/8
4 7/8
7 11/16 8 11/16 7 11/16
7 11/16 8 11/16 7 11/16
2 1/8
3 1/4
2 3/4
2 11/16
3 5/8
3 1/4
2 7/8
5 3/8
4 5/8
2 7/8
4
3 3/4
3 3/16 5 11/16 4 11/16
3 1/4
5 3/4
4 1/2
3 1/4
6 3/4
5 1/2
3 1/4
6 9/16
5 1/16
3 3/8
6 3/4
5
4 1/2
7 1/2
5 1/2
4 7/8
10 5/16 7 13/16
2 3/4
7 1/2
5 1/2
7 11/16 8 11/16 7 11/16
7 11/16 8 11/16 7 11/16
3 1/16
4
3
3
5 3/8
4 5/8
3
4
3 3/4
3 1/2
5 11/16 4 11/16
3 9/16
7
5 3/4
3 9/16
6 3/4
5 1/2
3 1/4
6 9/16
5 1/16
3 3/8
7 3/4
6
4 1/2
7 1/2
5 1/2
4 7/8
10 5/16 7 13/16
3 3/8
7 7/8
5 7/8
7 11/16 8 11/16 7 11/16
7 11/16 8 11/16 7 11/16
Note:
a. If A = X1 is less than 5 1/2, X=5 1/2
b. If B = X1 is less than 9 1/2, X=9 1/2
c. If C = X1 is less than 7, X=7
* If A + X1 and B + X1 are less than 12, X=12. If greater than 12, use the dimensions shown.
**If C + X1 is less than 9, X=9. If greater than 9, use dimensions shown.
Raise up to 6"
B
C
2
2 1/4
4 3/16
4 3/16
4 3/16
4 3/4
6 3/4
5 1/2
7 1/4
2
2 1/8
4 5/8
4 5/8
5 1/8
5 1/8
8
6 3/4
7 1/4
2 3/4
2 7/8
5 1/4
5 1/4
6 1/8
6 1/8
9 3/4
9 1/2
10 7/8
2 3/8
3
4 3/16
4 3/16
4 5/8
4 3/4
6 3/4
5 1/2
7 1/4
2 3/8
2 7/8
4 5/8
4 5/8
5 1/8
5 1/8
8
6 3/4
7 1/4
3 1/4
3 5/8
5 1/4
5 1/4
6 1/8
6 1/8
9 3/4
9 1/2
10 7/8
2 3/4
3 3/4
4 3/16
4 3/16
4 5/8
4 3/4
6 3/4
5 1/2
7 1/4
2 3/4
3 5/8
4 5/8
4 5/8
5 1/8
5 1/8
8
6 3/4
7 1/4
3 3/4
4 3/8
5 1/4
5 1/4
6 1/8
6 1/8
9 3/4
9 1/2
10 7/8
3 1/4
4 3/8
4 3/16
4 3/16
4 5/8
4 3/4
6 3/4
5 1/2
7 1/4
3 1/4
4 1/4
4 5/8
4 5/8
5 1/8
5 1/8
8
6 3/4
7 1/4
4 1/4
5
5 1/4
5 1/4
6 1/8
6 1/8
9 3/4
9 1/2
10 7/8
LIFETIME WARRANTY
Lifetime Warranty
Subject to the conditions stated herein, Duff-Norton will repair or replace, at its option, to
the original purchaser without charge, any parts proved to Duff-Nortons satisfaction to have
been defective in material or workmanship. Duff-Norton will not repair or replace any parts
that become inoperative because of normal repair or modification, improper installation,
eccentric loading, overloading, chemical or abrasive action, excessive heat, or other abuse.
Equipment and accessories not to Duff-Nortons manufacture are warranted only to the extent that they are warranted by the manufacturer, and only if the claimed defect arose during
normal use, applications and service.
EXCEPT AS STATED HEREIN, DUFF-NORTON MAKES NO OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
WARNING
The equipment shown in this catalog is intended for industrial use only and should not be used to lift, support,
or otherwise transport people unless you have written statement from the Duff-Norton Company which authorizes the specific actuator unit as used in your applications suitable for moving people.
All sales by Seller are made pursuant to the following terms. No other or additional terms or conditions are or will be accepted.
ACCEPTANCE OF ORDERS All orders, whether placed directly or through an agent, and all subsequent amendments thereto, are subject to a final approval and acceptance by Sellers main office.
LIMITATION OF WARRANTIES, REMEDIES AND DAMAGES
THE WARRANTY STATED BELOW IS GIVEN IN PLACE OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE. NO PROMISE OR AFFIRMATION OF FACT MADE BY ANY AGENT OR REPRESENTATIVE OF SELLER SHALL CONSTITUTE A WARRANTY BY SELLER OR GIVE RISE TO ANY LIABILITY OR OBLIGATION.
Seller warrants that on the date of its delivery to carrier the goods are free from defects in workmanship and materials.
SELLERS SOLE OBLIGATION IN THE EVENT OF BREACH OF WARRANTY OR CONTRACT OR FOR NEGLIGENCE OR OTHERWISE WITH RESPECT TO GOODS SOLD SHALL BE EXCLUSIVELY LIMITED TO REPAIR OR
REPLACEMENT, F.O.B. SELLERS POINT OF SHIPMENT, OF ANY PARTS WHICH SELLER DETERMINES TO HAVE BEEN DEFECTIVE or if Seller determines that such repair or replacement is not feasible, to a refund of
the purchase price upon return of the goods to Seller.
Any action against Seller for breach of warranty, negligence or otherwise must be commenced within one year after such cause of action accrues.
NO CLAIM AGAINST SELLER FOR ANY DEFECT IN THE GOODS SHALL BE VALID OR ENFORCEABLE UNLESS BUYERS WRITTEN NOTICE THEREOF IS RECEIVED BY SELLER WITHIN ONE YEAR FROM THE DATE OF
SHIPMENT.
Seller shall not be liable for any damage, injury or loss arising out of the use of the goods if, prior to such damage, injury or loss, such goods are (1) damaged or misused following Sellers delivery to carrier;
(2) not maintained, inspected, or used in compliance with applicable law and Sellers written instructions and recommendations; or (3) installed, repaired, altered or modified without compliance with such
law, instructions or recommendations.
UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES AS THOSE TERMS ARE DEFINED IN SECTION 2-715 OF THE UNIFORM COMMERCIAL CODE.
TERMS OF PAYMENT Unless otherwise stated herein, payment of each invoice is required within thirty (30) days after date of shipment. Any balance unpaid after the required payment date shall be subject to a service charge
of 1% per month from such date.
PRICE ADJUSTMENTS Amendments made by the Buyer to orders already placed shall, without formal notice to the Buyer, be subject to extra charges. If the estimated shipping date for the goods is more than sixty (60) days after
date of order, the price of the goods are subject to increase by Seller.
TAXES Any sales, use, excise, and other taxes applicable to this transaction and the goods and/or services furnished by Seller are not included in the price and shall be paid by Buyer when due. If Seller pays any
such taxes, Buyer shall reimburse Seller upon demand.
INDEMNIFICATION AND SAFE OPERATION Buyer shall comply with and require its employees to comply with directions set forth in instructions and manuals furnished by Seller and shall use and require its employees to follow such instructions and
manuals and to use reasonable care in the use and maintenance of the goods. Buyer shall not remove or permit anyone to remove any warning or instruction signs on the goods. In the event of personal injury
or damage to property or business arising from the use of the goods, Buyer shall, within forty-eight (48) hours thereafter, give Seller written notice of such injury or damage. Buyer shall cooperate with Seller in
investigating any such injury or damage and in the defense of any claims arising therefrom.
If Buyer fails to comply with this section or if any injury or damage is caused, in whole or in part, by Buyers failure to comply with applicable federal or state safety requirements, Buyer shall indemnify and
hold Seller harmless against any claims, loss or expense for injury or damage arising from the use of the goods.
GOVERNING LAW This agreement shall be governed by and construed under the laws of the State of New York.
DELIVERY AND DELAYS Unless otherwise specified herein, deliveries shall be F.O.B. Sellers point of shipment and risk of loss shall pass to Buyer upon Sellers delivery to carrier. All shipping dates are approximate and Seller shall
not be liable for loss or damage because of delays occasioned by labor disputes, damage to facilities, or failure of suppliers or subcontractors to meet scheduled deliveries or any other cause beyond Sellers
reasonable control or making its performance commercially impracticable.
Not withstanding other provisions hereof, if shipment is delayed at Buyers request, the goods shall be deemed to be stored at Buyers risk and expense and Seller may thereupon bill Buyer for the full price
and storage costs. Buyer shall pay such bill within 30 days after mailing thereof.
BUYERS INSPECTION UPON RECEIPT OF SHIPMENT Buyer shall inspect the goods as soon as received. If any loss or damage is discovered, Buyer must notify both the carrier and Seller at once. Seller will cooperate with Buyer in filing claims with the carrier.
CHANGES AND CANCELLATION Seller reserves the right to change or cancel any order whenever circumstances require allocation of production or delivery or Seller deems change or cancellation to be necessary to comply with applicable
laws, ordinances, regulations, directives or administrative actions. Seller reserves the right to make changes in materials or design which it determines appropriate for the goods.
SECURITY INTEREST AND REPOSSESSION Until full payment has been made therefor, Seller shall have a security interest in goods shipped to Buyer and the goods shall remain personal property. Upon request Buyer shall execute and deliver to
Seller security agreements and financing statements further evidencing Sellers security interest. Buyer authorizes Seller to file a financing statement or statements relating to the goods, without Buyers
signature thereon, as Seller may deem appropriate and appoints Seller as Buyers attorney-in-fact for the limited purpose of executing (without requiring Seller to do so) financing statements in Buyers name
and performing other acts which Seller deems appropriate to perfect and continue its security interest and to protect and preserve the goods.
In the event Buyer defaults in making any payment due Seller, Seller in addition to any other rights or remedies provided by law, shall have the right, with or without legal process, to enter the place where
said goods are located and to repossess the goods in accordance with the Uniform Commercial Code.
ASSURANCES Shipment by Seller shall at all times be subject to the prior approval of its credit personnel and Seller may, at any time, decline to make shipment except upon receipt of prior payment or upon other terms
and conditions or security satisfactory to such personnel.
PATENTS Except as to goods manufactured according to design supplied by Buyer, Seller will defend and hold Buyer free and harmless in a suit or proceeding brought against Buyer insofar as it is based on a claim
that use of the goods by Buyer constitutes an infringement of any existing U.S. Patents, provided, however, that Buyer gives Seller prompt written notice of such suit or proceeding; permits Seller, through
its counsel, to defend and/or settle the same; and gives Seller all necessary information, assistance and authority to enable Seller so to do. If Buyers use of the goods is held to constitute infringement and
further use is enjoined, Seller shall, at its option, either (i) procure for Buyer the right to continue using the goods; or (ii) replace the goods with non-infringing goods; or (iii) modify the goods to non-infringing
goods. The foregoing states Sellers entire liability for patent infringement and shall not be construed to render Seller liable for damages based on product output.
MISCELLANEOUS This instrument constitutes the entire agreement between Seller and Buyer, superseding all previous understandings and writings regarding this transaction. Any amendment or modification of this Agreement shall be void unless in writing and signed by Seller.
No delay or omission by Seller in exercising any right or remedy hereunder shall be a waiver thereof or of any other right or remedy, and no single or partial exercise thereof shall preclude any other or
further exercise thereof or the exercise of any other right or remedy. All rights and remedies of Seller are cumulative.
Sales made pursuant to this Agreement shall be governed by the Uniform Commercial Code as the same may from time to time be construed and in effect in the state wherein Seller has its main office.
ARBITRATION All disputes that may arise between the parties regarding the interpretation of the contract and the legal effect of the contract shall, to the exclusion of any court of law, be arbitrated and determined in accordance with the latest Commercial Arbitration Rules of the American Arbitration Association. The arbitration proceeding shall be held in the city in that state where the principal office of the Seller is located.
The parties recognize and consent to the above mentioned arbitration associations jurisdiction over each and every one of them.
USTS rev. 2/98
OTHER PRODUCTS
SuperCylinders
Linear Actuators
Rotary Unions
Linear Actuators
Electric Cylinders
Rotary Unions
www.duffnorton.com
ff-Norton
90
67
IS
Du
01
100
00
MACAT-2
7.5M ML 3/13