Académique Documents
Professionnel Documents
Culture Documents
www.parsethylene-kish.com
Designation: D1785 12
This standard is issued under the fixed designation D1785; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon () indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
ki
e-
se
th
yl
en
1. Scope*
1.1 This specification covers poly(vinyl chloride) (PVC)
pipe made in Schedule 40, 80, and 120 sizes and pressure-rated
for water (see Appendix X1). Included are criteria for classifying PVC plastic pipe materials and PVC plastic pipe, a
system of nomenclature for PVC plastic pipe, and requirements
and test methods for materials, workmanship, dimensions,
sustained pressure, burst pressure, flattening, and extrusion
quality. Methods of marking are also given.
1.2 The products covered by this specification are intended
for use with the distribution of pressurized liquids only, which
are chemically compatible with the piping materials. Due to
inherent hazards associated with testing components and systems with compressed air or other compressed gases some
manufacturers do not allow pneumatic testing of their products.
Consult with specific product/component manufacturers for
their specific testing procedures prior to pneumatic testing.
ar
Provided by : www.spic.ir
w
w
.p
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.25 on Vinyl
Based Pipe.
Current edition approved April 1, 2012. Published May 2012. Originally
approved in 1960. Last previous edition approved in 2006 as D1785 06. DOI:
10.1520/D1785-12.
2. Referenced Documents
2.1 ASTM Standards:2
D618 Practice for Conditioning Plastics for Testing
D1598 Test Method for Time-to-Failure of Plastic Pipe
Under Constant Internal Pressure
D1599 Test Method for Resistance to Short-Time Hydraulic
Pressure of Plastic Pipe, Tubing, and Fittings
D1600 Terminology for Abbreviated Terms Relating to
Plastics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
Compounds and Chlorinated Poly(Vinyl Chloride)
(CPVC) Compounds
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2152 Test Method for Adequacy of Fusion of Extruded
Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by
Acetone Immersion
D2672 Specification for Joints for IPS PVC Pipe Using
Solvent Cement
D2837 Test Method for Obtaining Hydrostatic Design Basis
for Thermoplastic Pipe Materials or Pressure Design Basis
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standards Document Summary page on
the ASTM website.
--`,,,,```,,```,,,`,,,````,`,,-`-`,,`,,`,`,,`---
sh
.c
om
www.parsethylene-kish.com
D1785 12
sh
.c
om
ki
NOTE 6The PVC pipe intended for use in the transport of potable
water should be evaluated and certified as safe for this purpose by a testing
agency acceptable to the local health authority. The evaluation should be
in accordance with requirements for chemical extraction, taste, and odors
that are no less restrictive than those included in NSF Standard No. 14.
The seal or mark of the laboratory making the evaluation should be
included on the pipe. See pipe marking requirement for reclaimed water
systems.
ar
2S/P 5 ~D0/t! 1
.p
--`,,,,```,,```,,,`,,,````,`,,-`-`,,`,,`,`,,`---
se
th
yl
en
3. Terminology
3.1 Definitions: Definitions are in accordance with Terminology F412 and abbreviations are in accordance with
Terminology D1600, unless otherwise specified. The abbreviation for poly(vinyl chloride) plastic is PVC.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 hydrostatic design stressthe estimated maximum
tensile stress the material is capable of withstanding continuously with a high degree of certainty that failure of the pipe
will not occur. This stress is circumferential when internal
hydrostatic water pressure is applied.
3.2.2 pressure rating (PR)the estimated maximum water
pressure the pipe is capable of withstanding continuously with
a high degree of certainty that failure of the pipe will not occur.
3.2.3 relation between dimensions, design stress, and pressure ratingthe following expression, commonly known as
the ISO equation,5 is used in this specification to relate
dimensions, hydrostatic design stress, and pressure rating:
4. Classification
4.1 GeneralThis specification covers PVC pipe made to
and marked with one of six type/grade/design stress designations (see X1.2) in Schedule 40, 80, and 120 wall sizes.
4.2 Hydrostatic Design StressesThis specification covers pipe made from PVC plastics as defined by four hydrostatic
design stresses which have been developed on the basis of
long-term tests (Appendix X1).
e-
Provided by : www.spic.ir
w
w
where:
S = hydrostatic design stress, psi (or MPa),
P = pressure rating, psi (or MPa),
D0 = average outside diameter, in. (or mm), and
t
= minimum wall thickness, in. (or mm).
3.2.4 standard thermoplastic pipe materials designation
codethe pipe materials designation code shall consist of the
abbreviation PVC for the type of plastic, followed by the
ASTM type and grade in Arabic numerals and the design stress
in units of 100 psi (0.7 MPa) with any decimal figures dropped.
When the design stress code contains less than two figures, a
cipher shall be used before the number. Thus a complete
material code shall consist of three letters and four figures for
PVC plastic pipe materials (see Section 5).
3
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
dodssp.daps.dla.mil.
4
Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann
Arbor, MI 48113-0140, http://www.nsf.org.
5
ISO R161-1960, Pipes of Plastics Materials for the Transport of Fluids (Outside
Diameters and Nominal Pressures) Part 1, Metric Series.
6. Requirements
6.1 Dimensions and Tolerances:
6.1.1 Dimensions and tolerances shall be as shown in Table
1 and Table 2 when measured in accordance with Test Method
D2122. The tolerances for out-of-roundness shall apply only to
pipe prior to shipment.
6.2 Sustained PressureThe pipe shall not fail, balloon,
burst, or weep as defined in Test Method D1598, at the test
pressures given in Tables 3-5 when tested in accordance with
8.4.
6.2.1 Accelerated Regression TestThe accelerated regression test shall be used in place of both the sustained and burst
pressure tests, at the option of the manufacturer. The test shall
be conducted in accordance with 8.4.1. The pipe shall demonstrate a hydrostatic design basis projection at the 100 000-h
intercept that meets the hydrostatic design basis category
requirement (see Tables 3-5 and Test Method D2837) for the
PVC material used in its manufacture. (Example: PVC 1120
pipe must have a minimum 100 000-h projection of 3830 psi
(26.40 MPa) and 85 % lower confidence limit (LCL).
6.3 Burst PressureThe minimum burst pressures for PVC
plastic pipe shall be as given in Table 6, when determined in
accordance with Test Method D1599.
NOTE 7Times greater than 60 s may be needed to bring large size
specimens to burst pressure. The test is more difficult to pass using greater
pressurizing times.
www.parsethylene-kish.com
D1785 12
TABLE 1 Outside Diameters and Tolerances for PVC Plastic Pipe Schedules 40, 80, and 120, in. (mm)
Tolerances
Maximum Out-of-Roundness (maximum minus minimum
diameter)
Nominal Pipe Size
Outside Diameter
...
...
...
...
...
...
...
...
...
...
...
0.100 (2.54)
0.100 (2.54)
0.100 (2.54)
0.100 (2.54)
0.150 (3.81)
0.150 (3.81)
0.150 (3.81)
0.200 (5.08)
0.320 (8.13)
0.360 (9.14)
0.400 (10.2)
0.480 (12.2)
0.016 (0.41)
0.016 (0.41)
0.016 (0.41)
0.016 (0.41)
0.020 (0.51)
0.020 (0.51)
0.024 (0.61)
0.024 (0.61)
0.024 (0.61)
0.030 (0.76)
0.030 (0.76)
0.030 (0.76)
0.030 (0.76)
0.060 (1.52)
0.070 (1.78)
0.090 (2.29)
0.100 (2.54)
0.120 (3.05)
...
...
...
...
...
ki
60.004 (60.10)
60.004 (60.10)
60.004 (60.10)
60.004 (60.10)
60.004 (60.10)
60.005 (60.13)
60.005 (60.13)
60.006 (60.15)
60.006 (60.15)
60.007 (60.18)
60.008 (60.20)
60.008 (60.20)
60.009 (60.23)
60.010 (60.25)
60.011 (60.28)
60.015 (60.38)
60.015 (60.38)
60.015 (60.38)
60.015 (60.38)
60.019 (60.48)
60.019 (60.48)
60.023 (60.58)
60.031 (60.79)
e-
0.405 (10.29)
0.540 (13.72)
0.675 (17.14)
0.840 (21.34)
1.050 (26.67)
1.315 (33.40)
1.660 (42.16)
1.900 (48.26)
2.375 (60.32)
2.875 (73.02)
3.500 (88.90)
4.000 (101.60)
4.500 (114.30)
5.563 (141.30)
6.625 (168.28)
8.625 (219.08)
10.750 (273.05)
12.750 (323.85)
14.000 (355.60
16.000 (406.40)
18.000 (457.20)
20.000 (508.00)
24.000 (609.60)
yl
14
en
3 8
1 2
3 4
1
1 1 4
1 1 2
2
2 1 2
3
3 1 2
4
5
6
8
10
12
14
16
18
20
24
18
sh
.c
om
Average
Nominal Pipe
Size
Schedule 40
w
w
(+0.51)
(+0.51)
(+0.51)
(+0.51)
(+0.51)
(+0.51)
(+0.51)
(+0.51)
(+0.51)
(+0.61)
(+0.66)
(+0.68)
(+0.71)
(+0.79)
(+0.86)
(+0.99)
(+1.12)
(+1.24)
(+1.35)
(+1.52)
(+1.70)
(+1.80)
(+2.08)
Wall ThicknessA
Schedule 80
Schedule 120
Minimum
Tolerance
Minimum
Tolerance
0.095 (2.41)
0.119 (3.02)
0.126 (3.20)
0.147 (3.73)
0.154 (3.91)
0.179 (4.55)
0.191 (4.85)
0.200 (5.08)
0.218 (5.54)
0.276 (7.01)
0.300 (7.62)
0.318 (8.08)
0.337 (8.56)
0.375 (9.52)
0.432 (10.97)
0.500 (12.70)
0.593 (15.06)
0.687 (17.45)
0.750 (19.05)
0.843 (21.41)
0.937 (23.80)
1.031 (26.19)
1.218 (30.94)
+0.020 (+0.51)
+0.020 (+0.51)
+0.020 (+0.51)
+0.020 (+0.51)
+0.020 (+0.51)
+0.021 (+0.53)
+0.023 (+0.58)
+0.024 (+0.61)
+0.026 (+0.66)
+0.033 (+0.84)
+0.036 (+0.91)
+0.038 (+0.96)
+0.040 (+1.02)
+0.045 (+1.14)
+0.052 (+1.32)
+0.060 (+1.52)
+0.071 (+1.80)
+0.082 (+2.08)
+0.090 (+2.29)
+0.101 (+2.57)
+0.112 (+2.84)
+0.124 (+3.15)
+0.146 (+3.71)
...
...
...
0.170 (4.32)
0.170 (4.32)
0.200 (5.08)
0.215 (5.46)
0.225 (5.72)
0.250 (6.35)
0.300 (7.62)
0.350 (8.89)
0.350 (8.89)
0.437 (11.10)
0.500 (12.70)
0.562 (14.27)
0.718 (18.24)
0.843 (21.41)
1.000 (25.40)
...
...
...
...
...
...
...
...
+0.020 (+0.51)
+0.020 (+0.51)
+0.024 (+0.61)
+0.026 (+0.66)
+0.027 (+0.68)
+0.030 (+0.76)
+0.036 (+0.91)
+0.042 (+1.07)
+0.042 (+1.07)
+0.052 (+1.32)
+0.060 (+1.52)
+0.067 (+1.70)
+0.086 (+2.18)
+0.101 (+2.56)
+0.120 (+3.05)
...
...
...
...
...
A
The minimum is the lowest wall thickness of the pipe at any cross section. The maximum permitted wall thickness, at any cross section, is the minimum wall thickness
plus the stated tolerance. All tolerances are on the plus side of the minimum requirement.
B
These dimensions conform to nominal IPS dimensions, with the exception that Schedule 120 wall thickness for pipe sizes 12 to 312 in. (12.5 to 87.5 mm), inclusive,
are special PVC plastic pipe sizes.
--`,,,,```,,```,,,`,,,````,`,,-`-`,,`,,`,`,,`---
Provided by : www.spic.ir
+0.020
+0.020
+0.020
+0.020
+0.020
+0.020
+0.020
+0.020
+0.020
+0.024
+0.026
+0.027
+0.028
+0.031
+0.034
+0.039
+0.044
+0.049
+0.053
+0.060
+0.067
+0.071
+0.082
ar
0.068 (1.73)
0.088 (2.24)
0.091 (2.31)
0.109 (2.77)
0.113 (2.87)
0.133 (3.38)
0.140 (3.56)
0.145 (3.68)
0.154 (3.91)
0.203 (5.16)
0.216 (5.49)
0.226 (5.74)
0.237 (6.02)
0.258 (6.55)
0.280 (7.11)
0.322 (8.18)
0.365 (9.27)
0.406 (10.31)
0.437 (11.10)
0.500 (12.70)
0.562 (14.27)
0.593 (15.06)
0.687 (17.45)
.p
14
38
12
34
1
114
112
2
212
3
312
4
5
6
8
10
12
14
16
18
20
24
18
Tolerance
se
Minimum
th
TABLE 2 Wall Thicknesses and Tolerances for PVC Plastic Pipe, Schedules 40, 80, and 120,A,B in. (mm)
6.5 Extrusion QualityThe pipe shall not flake or disintegrate when tested in accordance with Test Method D2152.
www.parsethylene-kish.com
D1785 12
TABLE 3 Sustained Pressure Test Conditions for Water at 73F
(23C) for PVC Plastic Pipe, Schedule 40
1690
1640
1310
1250
1010
950
770
690
580
640
590
500
470
410
370
330
300
280
270
270
270
260
250
1360
1310
1050
1000
810
760
620
560
470
510
440
400
370
330
300
260
240
220
220
220
220
210
200
psi
w
Provided by : www.spic.ir
yl
6.41
6.21
4.96
4.76
3.79
3.59
2.90
2.62
2.21
2.41
2.07
1.93
1.79
1.52
1.38
1.24
1.10
1.03
1.05
1.05
1.05
0.98
0.98
th
7.79
7.52
6.00
5.79
4.69
4.34
3.59
3.17
2.69
2.96
2.55
2.34
2.14
1.86
1.72
1.52
1.38
1.24
1.26
1.26
1.26
1.19
1.19
The fiber stresses used to derive these test pressures are as follows:
PVC1120
PVC1220
PVC2120
PVC2116
PVC2112
PVC2110
psi
4200
4200
4200
3360
2800
2300
MPa
29.0
29.0
29.0
23.2
19.3
15.9
1 4
3 8
1 2
3 4
1
114
112
2
212
3
312
4
5
6
8
10
12
14
16
18
20
24
2060
1900
1540
1430
1160
1060
870
790
680
710
630
580
540
490
470
410
390
380
380
370
370
370
360
1 2
3 4
1
114
112
2
212
3
312
4
5
6
8
10
12
14
16
18
20
24
18
14
38
PVC2112
PVC2110
psi
18
in.
ar
9.38
9.03
7.24
6.89
5.58
5.24
4.27
3.86
3.24
3.52
3.03
2.76
2.55
2.28
2.07
1.79
1.65
1.52
1.54
1.54
1.54
1.47
1.40
w
w
38
.p
11.65
11.31
9.03
8.62
6.96
6.55
5.31
4.76
4.00
4.41
4.07
3.45
3.24
2.83
2.55
2.28
2.07
1.93
1.89
1.89
1.89
1.82
1.75
14
930
900
720
690
550
520
420
380
320
350
300
280
260
220
200
180
160
150
150
150
150
140
140
MPa
18
2570
2370
1930
1780
1440
1320
1090
990
850
890
790
730
680
610
590
520
490
480
470
470
460
460
450
in.
1130
1090
870
840
680
630
520
460
390
430
370
340
310
270
250
220
200
180
180
180
180
170
170
se
in.
PVC2116
e-
1 4
3 8
1 2
3 4
1
114
112
2
212
3
312
4
5
6
8
10
12
14
16
18
20
24
18
1 2
3 4
1
114
112
2
212
3
312
4
5
6
8
10
12
14
16
18
20
24
PVC2110
PVC1120
PVC1220
PVC2120
en
in.
PVC2112
1720
1580
1290
1190
960
880
730
660
570
590
520
480
450
400
390
340
330
320
320
310
310
300
300
1410
1300
1060
980
790
720
600
540
460
490
430
400
370
330
320
280
270
260
260
260
250
250
250
11.86
10.90
8.89
8.20
6.62
6.07
5.03
4.55
3.93
4.07
3.59
3.31
3.10
2.76
2.69
2.34
2.28
2.21
2.24
2.17
2.17
2.10
2.10
9.72
8.96
7.31
6.76
5.45
4.96
4.14
3.72
3.17
3.38
2.96
2.76
2.55
2.28
2.21
1.93
1.86
1.79
1.82
1.82
1.75
1.75
1.75
sh
.c
om
PVC1120
PVC1220
PVC2120
ki
Nominal
Pipe
Size
MPa
17.72
16.34
13.31
12.27
9.93
9.10
7.52
6.83
5.86
6.14
5.45
5.03
4.69
4.21
4.07
3.59
3.38
3.31
3.29
3.29
3.22
3.22
3.15
14.21
13.10
10.62
9.86
8.00
7.31
6.00
4.96
4.69
4.90
4.34
4.00
3.72
3.38
3.24
2.83
2.69
2.62
2.66
2.59
2.59
2.59
2.52
The fiber stresses used to derive these test pressures are as follows:
PVC1120
PVC1220
PVC2120
PVC2116
PVC2112
PVC2110
psi
4200
4200
4200
3360
2800
2300
MPa
29.0
29.0
29.0
23.2
19.3
15.9
8. Test Methods
8.1 ConditioningCondition the test specimens at 73.4 6
3.6F (23 6 2C) and 50 6 10 % relative humidity for not less
www.parsethylene-kish.com
D1785 12
TABLE 5 Sustained Pressure Test Conditions for Water at 73F (23C) for PVC Plastic Pipe, Schedule 120
Pressure Required for TestA
Nominal Pipe
Size
PVC1120
PVC1220
PVC2120
PVC2116
2130
1620
1510
1250
1130
990
980
930
810
900
830
780
760
770
710
1710
1300
1200
1000
900
790
780
750
640
720
660
620
610
620
570
14.69
11.17
10.41
8.62
7.79
6.83
6.76
6.41
5.58
6.21
5.72
5.38
5.24
5.31
4.90
11.79
8.96
8.27
6.89
6.21
5.45
5.38
5.17
4.41
4.96
4.55
4.27
4.21
4.27
3.93
1170
890
830
680
620
540
540
510
440
490
450
430
420
420
390
e-
en
yl
th
9.79
7.45
6.89
5.72
5.17
4.55
4.48
4.27
3.72
4.14
3.79
3.59
3.52
3.52
3.31
8.07
6.14
5.72
4.69
4.27
3.72
3.72
3.52
3.03
3.38
3.10
2.96
2.90
2.90
2.69
ar
.p
PVC1120
PVC1220
PVC2120
PVC2116
PVC2112
PVC2110
se
The fiber stresses used to derive these test pressures are as follows:
w
w
psi
4200
4200
4200
3360
2800
2300
MPa
29.0
29.0
29.0
23.2
19.3
15.9
--`,,,,```,,```,,,`,,,````,`,,-`-`,,`,,`,`,,`---
MPa
3 4
1
1 1 4
1 1 2
2
2 1 2
3
3 1 2
4
5
6
8
10
12
12
ki
in.
Provided by : www.spic.ir
1420
1080
1000
830
750
660
650
620
540
600
550
520
510
510
480
psi
3 4
1
114
112
2
2 1 2
3
3 1 2
4
5
6
8
10
12
12
PVC2110
sh
.c
om
in.
PVC2112
www.parsethylene-kish.com
D1785 12
TABLE 6 Burst Pressure Requirements for Water at 73F (23C) for PVC Plastic Pipe, Schedules 40, 80, and 120
Min Burst PressuresA
Schedule 40
Schedule 80
PVC1120
PVC1220
PVC2120
PVC2112
PVC2116
PVC2110
PVC1120
PVC1220
PVC2120
2580
2490
1990
1910
1540
1440
1180
1060
890
970
840
770
710
620
560
500
450
420
410
410
410
390
380
2020
1950
1560
1490
1210
1130
920
830
690
760
660
600
560
390
440
390
350
330
320
320
320
310
300
3920
3620
2940
2720
2200
2020
1660
1510
1290
1360
1200
1110
1040
930
890
790
750
730
720
710
700
700
680
17.79
17.17
13.72
13.17
10.62
9.93
8.14
7.31
6.14
6.69
5.79
5.31
4.90
4.27
3.86
3.45
3.10
2.90
2.87
2.87
2.87
2.73
2.66
13.93
13.45
10.76
10.27
8.34
7.79
6.34
5.72
4.76
5.24
4.55
4.14
3.86
2.69
3.03
2.69
2.41
2.28
2.24
2.24
2.24
2.17
2.10
Provided by : www.spic.ir
th
se
ar
w
w
3060
2830
2300
2120
1720
1580
1300
1180
1010
1060
940
860
810
720
700
620
580
570
570
560
550
540
530
...
...
...
3250
2470
2300
1900
1720
1510
1490
1420
1230
1380
1260
1190
1160
1170
1090
...
...
...
...
...
...
...
...
2540
1930
1790
1490
1340
1180
1170
1110
960
1080
990
930
910
920
850
...
...
...
...
...
21.10
19.52
15.86
14.62
11.86
10.89
8.96
8.14
6.96
7.31
6.48
5.93
5.58
4.96
4.83
4.27
4.00
3.93
3.99
3.92
3.85
3.78
3.71
...
...
...
22.41
17.03
15.86
13.10
11.86
10.41
10.27
9.79
8.48
9.51
8.69
8.20
8.00
8.07
7.52
...
...
...
...
...
...
...
...
17.52
13.31
12.34
10.27
9.24
8.14
8.07
7.65
6.62
7.45
6.83
6.41
6.27
6.34
5.86
...
...
...
...
...
ki
eMPa
.p
14
38
12
34
1
1 1 4
1 1 2
2
212
3
312
4
5
6
8
10
12
14
16
18
20
24
27.03
24.96
20.27
18.76
15.17
13.93
11.45
10.41
8.89
9.38
8.27
7.65
7.17
6.41
6.14
5.45
5.17
5.03
5.04
4.97
4.90
4.90
4.76
yl
in.
18
PVC2112
PVC2116
PVC2110
psi
en
14
38
12
34
1
1 1 4
112
2
212
3
312
4
5
6
8
10
12
14
16
18
20
24
18
PVC1120
PVC1220
PVC2120
sh
.c
om
in.
Schedule 120
PVC2112
PVC2116
PVC2110
The fiber stresses used to derive these test pressures are as follows:
PVC1120
PVC1220
PVC2120
PVC2116
PVC2112
PVC2110
psi
6400
6400
6400
5000
5000
5000
MPa
44.1
44.1
44.1
34.5
34.5
34.5
--`,,,,```,,```,,,`,,,````,`,,-`-`,,`,,`,`,,`---
www.parsethylene-kish.com
D1785 12
sh
.c
om
en
ki
e-
th
yl
12. Keywords
12.1 pressure pipe; PVC pipe; Schedule 40 pipe; Schedule
80 pipe; Schedule 120 pipe
se
SUPPLEMENTARY REQUIREMENTS
ar
This requirement applies whenever a regulatory authority or user calls for product to be used to
convey or to be in contact with potable water.
w
w
.p
Provided by : www.spic.ir
--`,,,,```,,```,,,`,,,````,`,,-`-`,,`,,`,`,,`---
This requirement applies only to pipe to be used in systems that have not established other provisions for identification.
www.parsethylene-kish.com
D1785 12
GOVERNMENT/MILITARY PROCUREMENT
These requirements apply only to federal/military procurement, not domestic sales or transfers.
NOTE S3.1The inclusion of U.S. Government procurement requirements should not be construed as an indication that the U.S. Government
uses or endorses the products described in this specification.
en
e-
sh
.c
om
S2. Responsibility for InspectionUnless otherwise specified in the contract or purchase order, the producer is responsible for the performance of all inspection and test requirements specified herein. The producer may use his own or any
other suitable facilities for the performance of the inspection
and test requirements specified herein, unless the purchaser
disapproves. The purchaser shall have the right to perform any
of the inspections and tests set forth in this specification where
such inspections are deemed necessary to ensure that material
conforms to prescribed requirements.
ki
APPENDIX
yl
(Nonmandatory Information)
th
ar
se
X1.4 The pipe is rated for use with water at 73F (23C) at
the maximum internal pressures shown in Tables X1.1-X1.3.
Lower pressure ratings than those calculated in accordance
with 3.2.3 may be recommended, at the option of the pipe
manufacturer, in which case the SDR shall be included in the
marking. Experience of the industry indicates that PVC plastic
pipe meeting the requirements of this specification gives
satisfactory service under normal conditions for a long period
at these pressure ratings. The sustained pressure requirements
are related to these ratings through the slopes of the strengthtime plots of these materials in pipe form.
w
w
.p
Provided by : www.spic.ir
--`,,,,```,,```,,,`,,,````,`,,-`-`,,`,,`,`,,`---
www.parsethylene-kish.com
D1785 12
TABLE X1.1 Water Pressure Ratings at 73F (23C) for Schedule 40 PVC Plastic Pipe
Pressure RatingsA
Nominal
Pipe
Size
PVC1120
PVC1220
PVC2120
PVC2116
810
780
620
600
480
450
370
330
280
300
260
240
220
190
180
160
140
130
130
130
130
120
120
650
620
500
480
390
360
290
260
220
240
210
190
180
160
140
120
110
110
100
100
100
100
90
400
390
310
300
240
220
180
170
140
150
130
120
110
100
90
80
70
70
60
60
60
60
60
3.45
3.38
2.69
2.55
2.07
1.93
1.59
1.45
1.17
1.31
1.10
1.03
0.97
0.83
0.76
0.69
0.62
0.55
0.56
0.56
0.56
0.56
0.49
2.76
2.69
2.14
2.07
1.65
1.52
1.24
1.17
0.97
1.03
0.90
0.83
0.76
0.69
0.62
0.55
0.48
0.48
0.42
0.42
0.42
0.42
0.42
ki
e-
en
MPa
th
5.58
5.38
4.27
4.14
3.31
3.10
2.55
2.28
1.93
2.07
1.79
1.65
1.52
1.31
1.24
1.10
0.97
0.90
0.91
0.91
0.91
0.84
0.84
w
w
.p
ar
se
18
4.48
4.27
3.45
3.31
2.69
2.48
2.04
1.79
1.52
1.65
1.45
1.31
1.24
1.10
0.97
0.83
0.76
0.76
0.70
0.70
0.70
0.70
0.63
yl
in.
--`,,,,```,,```,,,`,,,````,`,,-`-`,,`,,`,`,,`---
500
490
390
370
300
280
230
210
170
190
160
150
140
120
110
100
90
80
80
80
80
80
70
psi
1 4
3 8
1 2
3 4
1
1 1 4
1 1 2
2
2 1 2
3
3 1 2
4
5
6
8
10
12
14
16
18
20
24
18
1 4
3 8
1 2
3 4
1
1 1 4
1 1 2
2
2 1 2
3
3 1 2
4
5
6
8
10
12
14
16
18
20
24
PVC2110B
sh
.c
om
in.
PVC2112B
Provided by : www.spic.ir
A
These pressure ratings apply only to unthreaded pipe. The industry does not recommend threading PVC plastic pipe in Schedule 40 dimensions in nominal pipe sizes
6 in. (150 mm) and smaller.
B
See Appendix X1 for code designation.
www.parsethylene-kish.com
D1785 12
TABLE X1.2 Water Pressure Ratings at 73F (23C) for Schedule 80 PVC Plastic Pipe
psi
PVC1120,
PVC1220,
PVC2120
PVC2116
PVC2112
PVC2110
Threaded
Unthreaded
Threaded
Unthreaded
Threaded
Unthreaded
Threaded
1 4
3 8
1 2
3 4
1
1 1 4
1
1 2
2
2 1 2
3
3 1 2
4
5
6
8
10
12
14
16
18
20
24
1230
1130
920
850
690
630
520
470
400
420
370
350
320
290
280
250
230
230
220
220
220
220
210
610
570
460
420
340
320
260
240
200
210
190
170
160
140
140
120
120
110
...
...
...
...
...
980
900
730
680
550
500
420
380
320
340
300
280
260
230
220
200
190
180
180
180
180
170
170
490
450
370
340
280
250
210
190
160
170
150
140
130
120
110
100
90
90
...
...
...
...
...
770
710
570
530
430
390
320
290
250
260
230
220
200
180
170
150
150
140
140
140
140
140
130
380
350
290
260
210
200
160
150
130
130
120
110
100
90
90
80
70
70
...
...
...
...
...
610
570
460
420
340
320
260
240
200
210
190
170
160
140
140
120
120
110
110
110
110
110
110
310
280
230
210
170
160
130
120
100
110
90
90
80
70
70
60
60
60
...
...
...
...
...
1 4
3 8
1 2
3 4
1
114
112
2
212
3
312
4
5
6
8
10
12
14
16
18
20
24
8.48
7.79
6.34
5.86
4.76
4.34
3.59
3.24
2.76
2.90
2.55
2.41
2.21
2.00
1.93
1.72
1.59
1.59
1.54
1.54
1.54
1.54
1.47
4.21
3.93
3.17
2.90
2.34
2.21
1.79
1.65
1.38
1.45
1.31
1.17
1.10
0.97
0.97
0.83
0.83
0.76
...
...
...
...
...
6.76
6.21
5.03
4.69
3.79
3.45
2.90
2.62
2.21
2.34
2.07
1.93
1.79
1.59
1.52
1.38
1.31
1.24
1.26
1.26
1.26
1.19
1.19
2.62
2.41
2.00
1.79
1.45
1.38
1.10
1.03
0.90
0.90
0.83
0.76
0.69
0.62
0.62
0.55
0.48
0.48
...
...
...
...
...
4.21
3.93
3.17
2.90
2.34
2.21
1.79
1.65
1.38
1.45
1.31
1.17
1.10
0.97
0.97
0.83
0.83
0.76
0.77
0.77
0.77
0.77
0.77
2.14
1.93
1.59
1.45
1.17
1.10
0.90
0.83
0.69
0.76
0.62
0.62
0.55
0.48
0.48
0.41
0.41
0.41
...
...
...
...
...
en
e-
ki
sh
.c
om
Unthreaded
18
MPa
Provided by : www.spic.ir
w
Copyright ASTM International
yl
3.38
3.10
2.55
2.34
1.93
1.72
1.45
1.31
1.10
1.17
1.03
0.97
0.90
0.83
0.76
0.69
0.62
0.62
...
...
...
...
...
th
se
ar
w
w
.p
18
5.31
4.90
3.93
3.65
2.96
2.69
2.21
2.0
1.72
1.79
1.59
1.52
1.38
1.24
1.17
1.03
1.03
0.97
0.98
0.98
0.98
0.98
0.91
--`,,,,```,,```,,,`,,,````,`,,-`-`,,`,,`,`,,`---
Nominal
Pipe
Size,
in.
www.parsethylene-kish.com
D1785 12
TABLE X1.3 Water Pressure Ratings at 73F (23C) for Schedule 120 PVC Plastic Pipe
psi
Unthreaded
Threaded
PVC2116
Unthreaded
PVC2112
Threaded
3 4
1
114
112
2
212
3
312
4
5
6
8
10
12
1010
770
720
600
540
470
470
440
380
430
400
370
380
370
340
510
390
360
300
270
240
230
220
190
220
200
190
180
180
170
810
620
570
480
430
380
370
360
310
340
320
300
290
290
270
410
310
290
240
210
190
190
180
150
170
160
150
140
140
140
3 4
1
114
112
2
212
3
312
4
5
6
8
10
12
6.96
5.31
4.96
4.14
3.72
3.24
3.24
3.03
2.62
2.96
2.76
2.55
2.62
2.55
2.34
3.52
2.69
2.48
2.07
1.86
1.65
1.59
1.52
1.31
1.52
1.38
1.31
1.24
1.24
1.17
5.58
4.27
3.93
3.31
2.96
2.62
2.55
2.48
2.14
2.34
2.21
2.07
2.00
2.00
1.86
2.83
2.14
2.00
1.65
1.45
1.31
1.31
1.24
1.03
1.17
1.10
1.03
0.97
0.97
0.97
12
Unthreaded
630
480
450
370
340
290
290
280
240
270
250
230
230
230
210
Threaded
510
390
360
300
270
240
230
220
190
220
200
190
180
180
170
250
190
180
150
130
120
120
110
100
110
100
90
90
90
80
3.52
2.69
2.48
2.07
1.86
1.65
1.59
1.52
1.31
1.52
1.38
1.31
1.24
1.24
1.17
1.72
1.31
1.24
1.03
0.90
0.83
0.83
0.76
0.69
0.76
0.69
0.62
0.62
0.62
0.55
e-
4.34
3.31
3.10
2.55
2.34
2.00
2.00
1.93
1.65
1.86
1.72
1.59
1.59
1.59
1.45
en
yl
Unthreaded
2.21
1.65
1.52
1.31
1.17
1.03
1.03
0.97
0.83
0.90
0.83
0.83
0.76
0.76
0.76
se
th
Threaded
320
240
220
190
170
150
150
140
120
130
120
120
110
110
110
MPa
12
PVC2110
sh
.c
om
PVC1120, PVC1220,
PVC2120
ki
Nominal
Pipe
Size,
in.
ar
SUMMARY OF CHANGES
.p
Committee F17 has identified the location of selected changes to this standard since the last issue (F178506)
that may impact the use of this standard.
w
w
Provided by : www.spic.ir
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/
COPYRIGHT/).
--`,,,,```,,```,,,`,,,````,`,,-`-`,,`,,`,`,,`---