Académique Documents
Professionnel Documents
Culture Documents
** ON A/C ALL
TASK 32-41-12-000-001-A
Removal of the NLG Wheel
WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
GEAR.
WARNING: ONLY REMOVE ONE WHEEL AND TIRE ASSEMBLY FROM THE NOSE LANDING GEAR AT
THE SAME TIME. IF YOU REMOVE THE TWO WHEEL AND TIRE ASSEMBLIES AT THE SAME
TIME, DAMAGE TO THE AIRCRAFT AND INJURY TO PERSONS CAN OCCUR.
C. Referenced Information
REFERENCE DESIGNATION
07-12-00-582-001-A Jacking of the Nose Landing Gear
32-00-00-481-001-A Installation of the Safety Devices on the Landing Gears
32-41-00-210-003-A Inspection/Check of the Tire Pressure
Nose Gear Wheel SHEET 1
A
1
2
3
4 A
2660GM
5 2659GM
A
6
11
10
5
4
3
2
9
8
7
N_MM_324112_4_AAM0_01_00
3. Job Set-up
Subtask 32-41-12-865-050-A
A. Open, safety and tag this(these) circuit breaker(s):
NOTE: If you must remove the wheel for access or inspections it is not necessary to deflate the tire
if:
- The tire is in correct condition.
- The tire pressure is in the Normal Operating Range. (Ref. AMM TASK 32-41-00-210-003)
If you have not these two conditions you must deflate the tire.
4. Procedure
(Ref. Fig. Nose Gear Wheel SHEET 1)
Subtask 32-41-12-010-051-A
A. Get access
(1) Remove the screws (7) and the washers (8).
(2) Remove the hubcap (6).
Subtask 32-41-12-020-050-A
B. Removal of the NLG wheel
(1) Remove and discard the two cotter pins (4) and the two nuts (3).
(2) Remove the washers (2) and the bolts (5).
(3) Remove and retain the casing (9).
(4) Remove the axle nut (10) with the ADAPTOR NLG (J47549) .
(5) Install the PROTECTOR NLG (J47548) .
TASK 32-41-12-400-001-A
Installation of the NLG Wheel
WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL
MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
GEAR.
B. Consumable Materials
REFERENCE DESIGNATION
(Material No. 03GBB1) Synthetic Oil base Grease-General Purpose Clay Thickened -
(Material No. 03GCB1) Synthetic Oil base Grease-Landing Gear Wheel Bearing Lithium
Thickened -
(Material No. 06LCG9) Non Hardening Jointing Putty-Medium Temp. Area - -
(Material No. 08BBB1) Non Aqueous Cleaner-- Petroleum Based -
D. Expendable Parts
E. Referenced Information
REFERENCE DESIGNATION
07-12-00-582-001-A Jacking of the Nose Landing Gear
12-14-32-614-001-A Nitrogen Filling of the Tires
32-00-00-081-001-A Removal of the Safety Devices from the Landing Gears
32-00-00-481-001-A Installation of the Safety Devices on the Landing Gears
32-41-00-210-003-A Inspection/Check of the Tire Pressure
32-41-00-910-001-A Tire Mixability Precautions
12-22-00-00 LUBRICATION - DESCRIPTION AND OPERATION
Nose Gear Wheel SHEET 1
3. Job Set-up
Subtask 32-41-12-865-051-A
A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
NOTE: If the wheel has a pressure-sensor seal cap, make sure that the seal cap is correctly installed and
safetied with a nut and a cotter pin.
NOTE: If the wheel has a Tire Pressure Indicating System (TPIS), the tie-bolt balance weight must be installed
180 degrees from the TPIS sensor holder.
Subtask 32-41-12-210-054-A
A. Tires of different type
(1) Obey the tire mixability precautions (Ref. AMM TASK 32-41-00-910-001) .
Subtask 32-41-12-420-053-A
B. Installation of the NLG Wheel
CAUTION: MAKE SURE THAT THE GREASE USED FOR THE AXLE SLEEVE IS THE SAME AS
THE GREASE USED FOR THE BEARINGS (CONE AND CAGE). IF YOU USE A DIFFER-
ENT GREASE, YOU CAN CAUSE DAMAGE TO THE BEARINGS.
NOTE: For lubricant grease specification and lubrication requirements, refer to (Ref. AMM D/
O 12-22-00-00) .
NOTE: You must make sure that the wheel does not turn when you loosen the axle nut.
(g) TORQUE the axle nut (10) to 10.8 m.daN (79.65 lbf.ft) with the ADAPTOR NLG (J47549) and,
at the same time, turn the wheel in the same direction.
(h) Tighten the axle nut (10).
CAUTION: MAKE SURE THAT YOU ALIGN THE NUT HOLE WITH THE SUBSEQUENT
AXLE HOLE (WITH THE SMALLEST POSSIBLE ROTATION ANGLE). IF YOU
1 Tighten the axle nut (10) until one hole is aligned with the first subsequent hole in the axle.
(i) Turn the wheel and make sure that the wheel is installed correctly.
(j) Install the casing (9).
(k) Installation of the bolts
CAUTION: MAKE SURE THAT YOU INSTALL THE BOLT AGAINST THE INNER SIDE OF
THE AXLE NUT, AND THE WASHERS AND NUTS AGAINST THE OUTER SIDE
OF THE AXLE NUT. IF YOU DO NOT, YOU CAN CAUSE DAMAGE TO THE
NOSE WHEEL.
1 Install the bolts (5), the washers (2) and the new IPC -CSN (32-21-13-12-070) nuts (3) or
IPC -CSN (32-21-13-22-070) nuts (3).
(l) TORQUE the nuts (3) to between 0.4 and 0.45 m.daN (35.40 and 39.82 lbf.in).
(m) Safety the nuts (3) with the new IPC -CSN (32-21-13-12-060) cotter pins (4) or IPC -CSN (32-
21-13-22-070) cotter pins (4).
Subtask 32-41-12-410-051-A
C. Close access
(1) Put the hubcap (6) in position.
(2) Apply a thin layer of Non Hardening Jointing Putty-Medium Temp. Area - - (Material No. 06LCG9) to
the screws (7).
(3) Install the screws (7) and the washers (8).
(4) TORQUE the screws (7) to between 0.4 and 0.51 m.daN (35.40 and 45.13 lbf.in).
NOTE: The hubcap attachment holes have screw-lock inserts. It is not necessary to install lockwire
on the screws (7).
Subtask 32-41-12-860-051-A
D. Aircraft Maintenance Configuration
(1) Inflate the tire to the unloaded pressure (Ref. AMM TASK 12-14-32-614-001) .
(2) Lower the aircraft on its wheels (Ref. AMM TASK 07-12-00-582-001) .
(3) Make sure that the pressure of the tire is correct (Ref. AMM TASK 32-41-00-210-003) .
Subtask 32-41-12-865-052-A
E. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
5. Close-up
Subtask 32-41-12-942-051-A
A. Removal of the Equipment
(1) Remove the safety devices from the landing gears (Ref. AMM TASK 32-00-00-081-001) .
(2) Make sure that the work area is clean and clear of tools and other items.
(3) Remove the warning notice(s).
TASK 32-41-12-000-002-A
Removal of the Axle Sleeve
REFERENCE DESIGNATION
32-41-12-000-001-A Removal of the NLG Wheel
Axle Sleeve SHEET 1
A
A
1
A 2660GM
2659GM
N_MM_324112_4_BAM0_01_00
3. Job Set-up
Subtask 32-41-12-010-050-A
A. Get access
(1) Remove the related landing gear wheel (Ref. AMM TASK 32-41-12-000-001) .
4. Procedure
(Ref. Fig. Axle Sleeve SHEET 1)
Subtask 32-41-12-020-051-A
A. Removal of the Axle Sleeve
(1) Remove the retaining ring (3).
(2) Remove the axle sleeve (2).
TASK 32-41-12-400-002-A
Installation of the Axle Sleeve
WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL
MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
REFERENCE DESIGNATION
(Material No. 03GBB1) Synthetic Oil base Grease-General Purpose Clay Thickened -
(Material No. 03GCB1) Synthetic Oil base Grease-Landing Gear Wheel Bearing Lithium
Thickened -
(Material No. 08BBB1) Non Aqueous Cleaner-- Petroleum Based -
B. Referenced Information
REFERENCE DESIGNATION
32-41-12-400-001-A Installation of the NLG Wheel
Axle Sleeve SHEET 1
3. Job Set-up
Subtask 32-41-12-640-052-A
A. Preparation for Installation
(1) Clean the axle (1) with Non Aqueous Cleaner-- Petroleum Based - (Material No. 08BBB1). Dry it with
filtered compressed air .
(2) Lightly lubricate the axle (1) and the axle protective sleeve (2) with Synthetic Oil base Grease-
General Purpose Clay Thickened - (Material No. 03GBB1) or as alternative Synthetic Oil base
Grease-Landing Gear Wheel Bearing Lithium Thickened - (Material No. 03GCB1).
4. Procedure
(Ref. Fig. Axle Sleeve SHEET 1)
Subtask 32-41-12-420-051-A
A. Installation of the Axle Sleeve
(1) Install the axle sleeve (2).
(2) Install the retaining ring (3).
5. Close-up
Subtask 32-41-12-410-050-A
A. Close access
(1) Install the related wheel (Ref. AMM TASK 32-41-12-400-001) .
(2) Make sure that the work area is clean and clear of tools and other items.
Figure 32-41-12-991-00100-00-A / SHEET 1/1 - Nose Gear Wheel
Figure 32-41-12-991-00200-00-A / SHEET 1/1 - Axle Sleeve
End of document