Académique Documents
Professionnel Documents
Culture Documents
com/easy
Application guide
EASY lighting control
Light is OSRAM
EASY lighting control | Contents
Contents
Please note:
All information in this guide has been prepared with great
care. OSRAM, however, does not accept liability for
possible errors, changes and/or omissions. Please check
www.osram.com or contact your sales partner for an up-
dated copy of this guide. This technical application guide is
for information purposes only and aims to support you in
tackling the challenges and taking full advantage of all op-
portunities the technology has to offer. Please note that this
guide is based on own measurements, tests, specic pa-
rameters and assumptions. Individual applications may not
be covered and need different handling. Responsibility and
testing obligations remain with the luminaire manufacturer/
OEM/application planner.
2
EASY lighting control | System overview
Each device has 4 separately dimmable output channels1) In addition to the user interfaces, a PC software is available
and operates in various modes depending on the connect- to provide access to the control devices via a USB adapter
ed consumer: (EASY PC KIT). Each control device can thus be congured
4-channel white individually and each scene in each sequence can be ad-
Tunable White justed. The cross-fade and hold times within a sequence
RGB can also be changed.
RGB-W
3
EASY lighting control | System overview
EASY RMC
EASY IR DALI EASY SO
R
G
DALI
B
W
DMX
EASY SYS CP
EASY RC
4
EASY lighting control | Conference room
DALI DALI
DALI DALI
DALI DALI
DALI DALI
DALI DALI
DALI DALI
DALI DALI
DALI DALI
5
EASY lighting control | Conference room
L
N
K1
EASY
DALI bus
DA 1+ EASY SO
DA 1-
DA 2+
DA 2-
DA 3+ 1
DA 3- 2
DA 4+ ON 3
DA 4- 4
1 T1
EASY
2 T2
3 T3
4 EASY T4
Push-Button T5
Coupler T6
T7
ON T8
GND
ON 1
Sc
Sc 2
en
en
/O
e
FF
/D
e.g. H07VV-F5G1.5 mm
IM
DALI circuit 4
e.g. H07VV-F5G1.5 mm
DALI circuit 3
e.g. H07VV-F5G1.5 mm
DALI circuit 2
e.g. H07VV-F5G1.5 mm
DALI circuit 1
6
EASY lighting control | Colored counter illumination
If required, the personnel at the reception can always stop, The individual colors and the brightness of the proceeding
continue and also adjust the color change. sequence are set and stored with the jog wheel of the re-
mote control. The dynamic sequence is started or stopped
by pressing a button.
7
EASY lighting control | Colored counter illumination
L 24V (+) +
N CH1 (R-) R
OT EASY 80 G
Master CH2 (G-)
EASY CH3 (B-) B
EASY RC EASY CH4 (W-)
bus
bus GND (-)
L 24V (+) +
N CH1 (R-) R
OT EASY 80 G
SLAVE CH2 (G-)
CH3 (B-) B
EASY CH4 (W-)
bus GND (-)
L 24V (+) +
N CH1 (R-) R
OT EASY 80 G
SLAVE CH2 (G-)
CH3 (B-) B
EASY CH4 (W-)
bus GND (-)
L 24V (+) +
N CH1 (R-) R
OT EASY 80 G
SLAVE CH2 (G-)
CH3 (B-) B
EASY CH4 (W-)
bus GND (-)
L 24V (+) +
N CH1 (R-) R
OT EASY 80 G
SLAVE CH2 (G-)
CH3 (B-) B
EASY CH4 (W-)
bus GND (-)
8
EASY lighting control | Showroom with Tunable White
9
EASY lighting control | Showroom with Tunable White
2.700K
L 24V (+) L 24V (+)
N OT EASY 80 CH1 (R-) N OT EASY 80 CH1 (R-)
Master CH2 (G-) 6.500K SLAVE CH2 (G-)
CH3 (B-) 2.700K CH3 (B-)
EASY CH4 (W-) EASY CH4 (W-)
bus GND (-) bus GND (-)
6.500K
2.700K
EASY
2.700K
L 24V (+) L 24V (+)
N OT EASY 80 CH1 (R-) N OT EASY 80 CH1 (R-)
SLAVE CH2 (G-) 6.500K SLAVE CH2 (G-)
CH3 (B-) 2.700K CH3 (B-)
EASY CH4 (W-) EASY CH4 (W-)
bus GND (-) bus GND (-)
6.500K
2.700K
L 24V (+) L 24V (+)
N OT EASY 80 CH1 (R-) N OT EASY 80 CH1 (R-)
SLAVE CH2 (G-) 6.500K SLAVE CH2 (G-)
CH3 (B-) 2.700K CH3 (B-)
EASY CH4 (W-) EASY CH4 (W-)
bus GND (-) bus GND (-)
6.500K
2.700K
L 24V (+) L 24V (+)
N OT EASY 80 CH1 (R-) N OT EASY 80 CH1 (R-)
SLAVE CH2 (G-) 6.500K SLAVE CH2 (G-)
CH3 (B-) 2.700K CH3 (B-)
EASY CH4 (W-) EASY CH4 (W-)
bus GND (-) bus GND (-)
6.500K
2.700K
L 24V (+) L 24V (+)
N OT EASY 80 CH1 (R-) N OT EASY 80 CH1 (R-)
L + CH2 (G-) 6.500K CH2 (G-)
24V
SLAVE SLAVE
N - CH3 (B-) 2.700K CH3 (B-)
EASY CH4 (W-) EASY CH4 (W-)
OT6 bus GND (-) bus GND (-)
6.500K
The system is ready for operation. For an overview of the features of the individual compo-
nents, see chapter 8 Components. Further information
Color and brightness can be adjusted with the jog wheel at can be found at www.osram.com/easy.
all times.
10
EASY lighting control | Recreation room with biological light effect
DALI DALI
DALI DALI
DALI DALI
DALI DALI
Timer
5 am to 8 pm
Mon-Fri
GND
GND
T1
T2
T3
Push-Button T4
T5
T6
T7
T8
T1
T2
T3
Push-Button T4
T5
T6
T7
T8
Coupler
Coupler
Automatic
EASY
EASY
operation
1
2
3
4
1
2
3
4
ON
ON
L
N
K1
EASY
DALI bus
DA 1+ EASY SO
DA 1-
DA 2+
DA 2-
DA 3+ 1
DA 3- 2
DA 4+ ON 3
DA 4- 4
L
N
K1
EASY Downlights
DALI bus
DA 1+ EASY SO
DA 1-
DA 2+
DA 2-
DA 3+ 1
DA 3- 2 Warm white
DA 4+ ON 3
DA 4- 4
Manual
Warm white
operation
Cold white
N
Cold white
12
EASY lighting control | Recreation room with biological light effect
13
EASY lighting control | Shop lighting and RGB cove lighting
Salesroom
DALI DALI
DALI DALI DALI
DALI DALI
DALI DALI DALI
DALI DALI
DALI DALI DALI
DALI DALI
DALI DALI DALI
14
EASY lighting control | Shop lighting and RGB cove lighting
6.2 Functional description junction box). The light scene for shop lighting is set with
The lighting control is divided into two parts: one part as the PC software of the EASY PC KIT. After set-up, an ad-
general and object lighting system with static light scenes justment of the scene is possible at all times with the EASY
and one part as cove lighting system with a dynamic se- PC KIT. The cove lighting system is supplied by compact
quence. The control of the general and object lighting sys- control devices with integrated power supply and 4-chan-
tem is integrated into the electrical cabinet as a DIN-rail- nel dimmer. The control devices are placed close to the
mounted device and controls four DALI circuits. These four LED strips (to avoid long secondary cables and related
DALI circuits are wired separately from the control output EMI). The individual control devices are connected to each
right to the last luminaire. The lighting control is operated other via the EASY bus line. The sequence is set with the
with a push-button. In closed state, the scene Shop light- EASY PC KIT and the corresponding PC software. After
ing is recalled, in open state, all luminaires are switched set-up, the sequence can be adjusted at all times with the
off. The push-button is connected to the control system EASY PC KIT.
via a push-button coupler (behind the push-button in the
L 1 T1
EASY
N 2 T2
3 T3
4 EASY T4
K1 Push-Button T5
Sequence 1
EASY Coupler T6
DALI bus
DA 1+ EASY SO T7
DA 1- ON T8
DA 2+ GND
DA 2-
Sc
DA 3+ 1
en
e1
DA 3- 2
DA 4+ ON 3
DA 4- 4
DALI circuit 4
T1
T2
T3
T4
T5
T6
T7
T8
GND
Push-Button
DALI circuit 3
Coupler
EASY
DALI circuit 2
EASY
DALI circuit 1
1
2
3
4
ON
L 24V (+) +
N CH1 (R-) R
OT EASY 80 G
Master CH2 (G-)
CH3 (B-) B
EASY CH4 (W-)
bus GND (-)
L 24V (+) +
N CH1 (R-) R
OT EASY 80 G
SLAVE CH2 (G-)
CH3 (B-) B
EASY CH4 (W-)
bus GND (-)
L 24V (+) +
N CH1 (R-) R
OT EASY 80 G
SLAVE CH2 (G-)
CH3 (B-) B
EASY CH4 (W-)
bus GND (-)
15
EASY lighting control | Shop lighting and RGB cove lighting
16
EASY lighting control | Colored facade lighting
The color and brightness of each single light point are set
DMX DMX
by the simple and intuitive software. To generate the se-
DMX
quence, the hold and cross-fade times can be set sepa- DMX DMX
DMX DMX DMX
rately for each scene.
L
N
Pe
EASY EASY DMX 16x4
bus
EASY
DMX out
DMX in DMX in
Shield
Shield
-
bus
1 +
2 EASY DMX
-
3 ON ON L L
4 Shield N N
Pe Pe
Shield
Shield
+
-
-
+
DMX in DMX in
Shield
Shield
-
L L
N N
Pe Pe
Shield
Shield
+
-
Photocell
switch
1 T1
+
DMX in DMX in
Shield
Shield
-
2 EASY T2 Timer
3 T3
Push-Button T4 5 am to 8 pm
4 Coupler T5 L L
T6 N N
T7
ON T8 Pe Pe
Shield
Shield
GND
DMX out DMX out
+
+
-
17
EASY lighting control | Colored facade lighting
7.4 Commissioning
1. Connect the luminaires to the EASY DMX 16x4 SO
control device
Set the DMX addresses (automatically or manually via
DIP switch etc. depending on luminaire)
Connect the DMX luminaires according to DMX
standard
Connect the DMX cables to the control device
Connect the mains to the luminaires
2. Connect the push-button coupler to the control device
The control device has several EASY inputs. The push-
button coupler can be directly connected via the EASY
terminals.
Set the operating mode of the push-button coupler via
DIP switch (see wiring diagram)
ON
Connect a standard photocell switch and a timer with Each scene can be activated/deactivated
dry contact to the push-button coupler For each scene, different hold and cross-fade times
3. Connect the mains to the control device can be set (up to 24 h)
4. Set the sequence via the EASY PC KIT 5. Disconnect the EASY PC KIT
Connect the laptop with the EASY PC KIT via USB to
the EASY interface of the control device (dedicated port The system is ready for operation and the sequence
on the front of the device) will be activated via photocell switch and timer.
Start the software and read in the DMX luminaires (the
DMX luminaires are addressed)
Set the colors per scene for all devices at once
7.5 Applied control components
18
EASY lighting control | Components at a glance
8 Components at a glance
8.1 Control devices
4-channel PWM dimmer with integrated 24-V power Control device with 4 DALI broadcast channels for
supply 80 W and control device in one device light ceiling/luminaire integration
Suitable for 24-V constant-voltage LED modules 4 separately controllable DALI channels
The following operating modes can be selected: No DALI commissioning/addressing required, address-
RGB or RGB-W ing is carried out via wiring
Tunable White Up to 32 DALI ECGs can be connected, distributed
Individual control of the channels asymmetrically or symmetrically over the individual
A total of 80 W can be connected, distributed asymmet- channels
rically or symmetrically over the individual channels Total length of DALI line of up to 300 m across all
Up to 64 devices can be synchronized to control high channels
wattages (LED wattage of up to 5 kW) Up to 64 devices can be synchronized (theoretically, up
Including integrated cable clamp to 2 000 DALI ECGs)
Extremely easy and quick commissioning (ready out of Extremely easy and quick commissioning (ready out of
the box: sequence starts automatically when the device the box: sequence starts automatically when the device
is connected to the mains) is connected to the mains)
Dimensions: L x W x H: 245 x 47 x 44 mm Optional cable clamp available (LMS CI box)
Dimensions: L x W x H: 189 x 30 x 21 mm
Control device with 4 DALI broadcast channels for Control device for up to 16 individual DMX light points
electrical cabinet integration DMX control device with one output according to
DMX512-A standard
Same as DALI EASY III including the following additional Up to 32 DMX devices can be connected to a single
functions: control device
Designed as DIN-rail-mounted device Up to 16 DMX light points can be connected (one light
Controllable output relay (3 A) point consists of 14 addresses)
2 inputs for dry contacts Several DMX devices can be combined to one light
On/off/dimming of all channels point (same addresses)
Input for timer for recall of scenes/sequences 4 EASY DMX can be connected to each other and up to
Dimensions: L x W x H: 96 x 108 x 62 mm 64 different DMX light points can be controlled
The setting of the individual channels is carried out with
the EASY PC KIT and the corresponding easy-to-use
software
Dimensions: L x W x H: 96 x 102 x 62 mm
Push-button coupler with 8 inputs and 6 different Infrared remote control for single-channel and scene
operating modes control
For switching and dimming, central or single channels; Individual switching or dimming of channel 1 to 4
recall and storage of lighting scenes; start and stop of Up to 4 scenes can be stored and recalled
sequences One sequence can be recalled
Operating mode can be adjusted via DIP switch (no Speed and colors of the sequence can be adjusted
addressing of the coupler required) Including docking station for wall mounting
Suitable for integration into a junction box Dimensions: L x W x H: 120 x 57 x 26 mm
Can be combined with all standard switching programs
Dimensions: L x W x H: 245 x 47 x 44 mm
Brand: OSRAM
Type: EASY Hybrid Remote
EAN: 4008321421739
20
EASY lighting control | Components at a glance
8.3 Accessories
EASY IR CI EASY IR
Infrared receiver for ceiling integration Infrared receiver for device integration
Receiver for EASY RMC or EASY Hybrid Remote user Receiver for EASY RMC or EASY Hybrid Remote user
interfaces interfaces
Small diameter of d = 50 mm Suitable for luminaire integration
Direct connection to EASY control devices With connected cable 2.1 m and 4p4c connector
Including additional connection cable 2.1 m and Direct connection to EASY control devices
2 x 4p4c socket and 4-pole terminal Dimensions: L x W x H: 30 x 21 x 12 mm
Housing for surface mounting optionally available
(SENSOR KIT)
Dimensions: D x H: 50 x 21 mm
21
EASY lighting control | Components at a glance
Branching for EASY bus system Branching for EASY bus system
3-pole 4p4c socket, internal connection 2-pole 4p4c socket including 2 x 4-pole terminal with
Including 2 connection cables with 2.1 m each corresponding internal connection
Mounting with adhesive pad on bottom Connection of 4-wire cables with the EASY connector
Dimensions: L x W x H: 34 x 18 x 16 mm system
Including 2 connection cables with 2.1 m each
Mounting with adhesive pad on bottom
Dimensions: L x W x H: 40 x 20 x 16 mm
22
EASY lighting control | Components at a glance
LF05CA-RGB3-P LINEARlight Colormix Flex Protect LF05CA2-RGB3 LINEARlight Colormix Flex Protect
Flexibly splittable RGB LED strip with type of Flexibly splittable RGB LED strip
protection IP67 Alternatively available as 39-W module with a length of 6 m
Alternatively available as 39-W module with a length of 6 m and 1 080 lm. Additional feeders optionally available.
and 1 080 lm. Additional feeders optionally available. Suitable for cove lighting.
Suitable for cove lighting. For indoor areas
For indoor and outdoor areas 24-V RGB LED strip
24-V RGB LED strip Power: 72 W
Power: 72 W Length: 4 m
Length: 4 m Luminous ux: 1 880 lm
Luminous ux: 1 740 lm Beam angle: 120
Beam angle: 120 Lifetime: 50 000 h
Lifetime: 50 000 h Optimal control with OT EASY 80
Optimal control with OT EASY 80 Dimensions: L x W x H: 8 x 2.2 x 4 000 mm
Dimensions: L x W x H: 11 x 4.5 x 4 000 mm
Flexible chain consisting of six LED modules with Flexible chain consisting of six LED modules with
four warm white/cold white LEDs each (IPX5) four RGB-W LEDs each (IPX5)
Optimized for the backlighting of translucent foils (light Optimized for the backlighting of translucent foils (light
ceilings). Mounting accessories and heat sink optionally ceilings). Mounting accessories and heat sink optionally
available. available.
Voltage: 24 V direct current Voltage: 24 V direct current
Power: 24 W Power: 27 W
Length: max. 3 m (0.5 m between 2 modules) Length: max. 3 m (0.5 m between 2 modules)
Luminous ux: 1 770 lm Luminous ux: 1 198 lm
LED light color: Tunable White 2 700 K 6 500 K LED light color: Tunable White 2 700 K 6 500 K
Beam angle: 135 Beam angle: 135
Lifetime: 40 000 h Lifetime: 40 000 h
Optimal control with OT EASY 80 (3 DRAGONchain can Optimal control with OT EASY 80 (2 DRAGONchain can
be connected in parallel) be connected in parallel)
Dimensions: L x W x H: max. 3 000 x 39 x 6.4 mm Dimensions: L x W x H: max. 3 000 x 39 x 6.4 mm
Disclaimer
All information contained in this document has been col-
lected, analyzed and veried with great care by OSRAM.
However, OSRAM GmbH is not responsible for the correct-
ness and completeness of the information contained in this
document and OSRAM GmbH cannot be made liable for
any damage that occurs in connection with the use of and/
or reliance on the content of this document. The informa-
tion contained in this document reects the current state of
knowledge on the date of issue.
24
www.osram.com/easy
04/15 OSRAM S-GI MK EM Subject to change without notice. Errors and omissions excepted.
OSRAM GmbH
Head ofce:
Marcel-Breuer-Strasse 6
80807 Munich, Germany
Phone +49 89 6213-0
Fax +49 89 6213-2020
www.osram.com