Académique Documents
Professionnel Documents
Culture Documents
Agrokid 220
->ZKDS2102V0MD20001
Agrokid 220
->ZKDS2902V0MD20001
Agrokid 230
->ZKDS2202V0MD20001
Agrokid 230
->ZKDS3002V0MD20001
Workshop manual
CONTENTS
0 - Introduction
0.1 - Introduction 0-2
0.1.1 - Safety notes 0-2
0.1.2 - General safety rules 0-2
0.1.3 - Safety precautions for removal and refitting operations 0-3
0.1.4 - Lifting instructions 0-4
0.1.5 - Tightening torques 0-5
0.1.6 - Threadlockers, adhesives, sealants and lubricants 0-8
0.1.7 - Conversion factors 0-10
10 - Technical characteristics
10.1 - Transmission 10-2
10.1.1 - Transmission 10-2
10.1.2 - Rear PTO and Mid PTO 10-8
10.2 - Rear axle 10-13
10.2.1 - Brakes and rear axle assembly 10-13
10.3 - Front axle 10-14
10.3.1 - Front axle 10-14
10.4 - Hydraulic system 10-17
10.4.1 - Gear pump 10-17
10.4.2 - Differential lock control assembly 10-18
10.4.3 - Steering circuit 10-20
10.4.4 - Power steering valve 10-22
10.4.5 - Remote control valve 10-23
30 - Method of intervention
30.1 - B0 - Engine 30-2
30.1.1 - PREPARATION FOR DISASSEMBLY 30-2
30.1.2 - Engine - Separation from the transmission 30-3
30.1.3 - Engine 30-10
30.1.4 - Compression test 30-11
30.1.5 - engine block, crankshaft, pistons and sump 30-13
30.1.6 - Inspection of the engine monobloc 30-23
30.1.7 - Inspection of the crankshaft 30-23
30.1.8 - Fan - alternator drivebelt 30-26
30.1.9 - A/C fan - compressor drivebelt 30-29
30.1.10 - Crankshaft pulley 30-32
30.1.11 - Flywheel bearing 30-33
30.1.12 - Timing gears and flywheel 30-33
30.1.13 - Inspection of the flywheel and ring gear 30-44
30.1.14 - Inspection of the pistons, piston rings and gudgeon pins 30-45
30.1.15 - Inspection of the connecting rods 30-47
30.1.16 - Inspection of the camshaft 30-48
III
CONTENTS
30.1.17 - Inspection of the camshaft 30-49
30.1.18 - Inspection of the idler gear 30-50
30.1.19 - Inspection of the valves, valve guides and valve seats 30-50
30.1.20 - Valve clearances 30-53
30.1.21 - Inspection of the rocker arms and rocker shaft 30-55
30.1.22 - Cylinder head and valve train components 30-55
30.1.23 - Inspection of the cylinder head 30-62
30.1.24 - Inspection of the valve springs 30-62
30.1.25 - Inspection of the valve pushrods 30-62
30.1.26 - Renewal of the jets 30-62
30.1.27 - Lubrication System 30-63
30.1.28 - Inspection of the lubrication system 30-65
30.1.29 - Fuel System 30-66
30.1.30 - Inspection and adjustment of the fuel system 30-69
30.1.31 - Inspection of the fuel lift pump 30-71
30.1.32 - Injection pump 30-71
30.1.33 - Inspection of the fuel injection pump camshaft 30-78
30.1.34 - Inspection of the fuel injection pump camshaft 30-79
30.1.35 - Fuel injection nozzle 30-80
30.1.36 - Maintenance of the injector nozzles 30-82
30.1.37 - Governor 30-83
30.1.38 - Cooling system 30-85
30.1.39 - Inspection of the cooling system 30-87
30.1.40 - Engine air intake pipe 30-89
30.1.41 - Intake and exhaust systems 30-90
30.1.42 - Inspection of the air intake and exhaust system 30-91
30.2 - C0 - Engine accessories 30-93
30.2.1 - Engine cooling system radiator 30-93
30.2.2 - Expansion tank 30-96
30.2.3 - Fan 30-97
30.2.4 - Air cleaner assembly 30-98
30.2.5 - Fuel filter 30-99
30.2.6 - Fuel tank - Fuel tank float switch 30-99
30.2.7 - Auxiliary fuel tank 30-103
30.2.8 - Engine stop keyswitch 30-104
30.2.9 - Exhaust pipe - tractor with cab 30-106
30.2.10 - Engine stop keyswitch 30-107
30.2.11 - Alternator 30-109
30.2.12 - Alternator 30-112
30.2.13 - Starter motor 30-116
30.2.14 - Starter motor 30-118
30.2.15 - Disassembly of the starter motor 30-120
30.3 - D0 - Transmission 30-127
30.3.1 - Clutch plate 30-127
30.3.2 - Checking clutch plate wear 30-128
30.3.3 - Clutch release bearing 30-128
30.3.4 - Clutch release forks 30-129
30.3.5 - Clutch housing 30-131
IV
CONTENTS
30.3.6 - Disassembly of the gearbox input shaft 30-135
30.3.7 - Disassembly of the main shaft 30-137
30.3.8 - Disassembly of the secondary shaft 30-138
30.3.9 - Gearbox and shuttle assembly - complete unit 30-141
30.3.10 - Gearbox and shuttle assembly - complete unit 30-142
30.3.11 - Range gearbox and differential assembly - complete unit 30-146
30.3.12 - Gearbox input shaft - oil seal renewal 30-148
30.3.13 - Bevel gear pair 30-149
30.3.14 - Disassembly of 4WD output shaft and groundspeed PTO 30-153
30.3.15 - Creeper - synchronizer renewal 30-155
30.3.16 - PTO output shaft. 30-157
30.3.17 - Disassembly of the PTO output shaft. 30-158
30.3.18 - Removal of the PTO output shaft 30-158
30.3.19 - Parking brake 30-160
30.3.20 - Adjustment of the bevel gear pair 30-162
30.4 - E0 - Rear axle 30-166
30.4.1 - Left-hand rear axle 30-166
30.4.2 - Disassembly of LH/RH rear axle 30-168
30.4.3 - Rear differential 30-172
30.4.4 - Disassembly of the rear differential 30-175
30.4.5 - Rear axle brake discs 30-176
30.5 - F0 - Front axle 30-178
30.5.1 - Front support 30-178
30.5.2 - Front axle - complete assembly 30-182
30.5.3 - Steering cylinders 30-184
30.5.4 - Steering cylinders disassembly 30-186
30.5.5 - Steering knuckle housing and axle shaft 30-188
30.5.6 - Disassembly of the bevel gear pair 30-190
30.5.7 - Propeller shaft - Front axle drive shaft 30-198
30.5.8 - Planetary reduction gear 30-199
30.5.9 - Disassembly of the planetary reduction gear 30-200
30.6 - G0 - Bodywork - Cab - Platform 30-205
30.6.1 - Cab 30-205
30.6.2 - Hood and side panels 30-212
30.6.3 - Cab access steps 30-216
30.6.4 - Adjustable front fenders 30-217
30.6.5 - Cab door lock - tie-rod 30-217
30.6.6 - Instrument panel 30-219
30.6.7 - Left-hand rear cab pillar - screenwash reservoir 30-220
30.6.8 - Right-hand console 30-221
30.6.9 - Left-hand console 30-222
30.6.10 - Instrument panel 30-223
30.6.11 - Centre console 30-224
30.6.12 - RH rear cab pillar trim 30-225
30.6.13 - A/C system air intake filters 30-225
30.6.14 - Cab roof 30-226
30.6.15 - Seat 30-230
30.6.16 - Air conditioning system - Standard roof version 30-231
V
CONTENTS
30.6.17 - Air conditioning compressor 30-233
30.6.18 - Condenser 30-235
30.6.19 - Receiver-dryer 30-236
30.6.20 - Evaporator assembly 30-237
30.6.21 - Air conditioner fan 30-238
30.6.22 - Bistable pressure switch for compressor clutch engagement/disengagement 30-239
30.6.23 - Steering wheel 30-240
30.6.24 - Adjustment of the lift control valve levers 30-241
30.6.25 - Remote valve control levers 30-243
30.7 - H0 - Hydraulic system 30-244
30.7.1 - Pump for hydraulic lift and auxiliary services and power steering system 30-244
30.7.2 - Transmission oil filter assembly 30-245
30.7.3 - Power steering valve - Complete assembly 30-246
30.7.4 - Power steering disassembly 30-248
30.7.5 - Pressure relief valve - lift control valve 30-260
30.7.6 - Lift locking shut-off valve 30-261
30.7.7 - Remote control valve 30-262
30.7.8 - Remote control valve 30-262
30.7.9 - Control rods 30-264
30.7.10 - Double/single acting conversion valve 30-265
30.8 - L0 - Electrical system 30-267
30.8.1 - Battery 30-267
30.8.2 - Fuse and relay assembly 30-268
30.8.3 - Electrostatic unit 30-269
30.8.4 - Parking brake switch 30-270
30.8.5 - Adjustment of the parking brake switch 30-271
30.8.6 - Brake lights switches 30-272
30.8.7 - Adjustment of the brake light switches 30-273
30.8.8 - Steering column switch 30-273
30.8.9 - Control buttons - RH console 30-273
30.9 - M0 - Front PTO 30-276
30.9.1 - Pump - clutch assembly - brake 30-276
30.9.2 - PTO output shaft 30-279
30.9.3 - Solenoid valve 30-281
30.10 - N0 - Front lift 30-283
30.10.1 - Front lift - version with front PTO - 30-283
30.10.2 - Cylinder 30-285
30.11 - R0 - Rear lift 30-287
30.11.1 - Rear lift - complete assembly 30-287
30.11.2 - Rear lift - complete assembly 30-289
30.11.3 - Adjustment of the rear lift 30-294
30.11.4 - Lift cylinders 30-296
30.11.5 - Lift cylinders 30-297
30.11.6 - Renewal of the rear lift bush 30-298
30.11.7 - Lift arms 30-299
30.11.8 - Hydraulic lift control valve 30-301
30.11.9 - Disassembly of the lift control valve 30-302
VI
CONTENTS
30.11.10 - Three-point linkage with mechanical adjustment 30-307
30.12 - S0 - Wheels 30-309
30.12.1 - Front wheels 30-309
30.12.2 - Rear wheels 30-309
30.13 - V0 - Ballast - towing hitches 30-310
30.13.1 - Support and towing hitch 30-310
40 - Wiring diagrams
40.1 - Introduction 40-2
40.1.1 - Structure of the unit 40-2
40.1.2 - Wiring and components index 40-6
40.1.3 - Introduction 40-6
40.1.4 - Basic electronics for mechanics (1/2) 40-9
40.1.5 - Basic electronics for mechanics (2/2) 40-11
40.1.6 - Electrical and electronic components (1/2) 40-18
40.1.7 - Electrical and electronic components (2/2) 40-26
40.2 - Components 40-31
40.2.1 - Components 40-31
40.3 - Systems 40-35
40.3.1 - Earthing points 40-35
40.3.2 - Starting 40-37
40.3.3 - Control unit - Fan 40-39
40.3.4 - Steering column lights switch 40-40
40.3.5 - Instrument panel 40-43
40.3.6 - Cab 40-45
40.3.7 - Aereo cab 40-48
40.3.8 - PTO 40-51
40.3.9 - Front axle differential lock 40-53
40.3.10 - Brakes 40-55
40.4 - Wiring harnesses 40-57
40.4.1 - Wiring harnesses 40-57
40.4.2 - Positions of front wiring connectors 40-58
40.4.3 - Front PTO wiring - 0.014.2645.4 40-61
40.4.4 - Positions of front PTO wiring connectors. 40-61
40.4.5 - Front lights wiring - 0.014.7599.4 40-63
40.4.6 - Positions of front light wiring connectors 40-64
40.4.7 - Compressor wiring - 0.014.7601.4 40-65
40.4.8 - Positions of compressor wiring connectors 40-65
40.4.9 - Front wiring with cab 40-66
40.4.10 - Positions of front wiring connectors with cab 40-68
40.4.11 - Central wiring - 0.012.6949.4 40-71
40.4.12 - Positions of central wiring connectors 40-75
40.4.13 - Solenoid valve wiring - 0.014.1482.4 40-80
40.4.14 - Positions of solenoid valve wiring connectors 40-81
40.4.15 - Rear wiring - 0.013.1452.4/10 40-82
40.4.16 - Positions of rear wiring connectors 40-84
40.4.17 - Remote valve wiring - 0.012.6955.4 40-86
VII
CONTENTS
40.4.18 - Rear lights wiring - 0.014.7602.4 40-86
40.4.19 - Positions of rear light wiring connectors 40-87
40.4.20 - Aereo cab wiring - 0.014.7593.4 40-89
40.4.21 - Positions of aereo-cab wiring connectors 40-91
40.4.22 - Cab power supply - 0.014.7594.4 40-92
40.4.23 - Positions of cab power supply wiring connectors 40-93
40.4.24 - Air conditioning system - 0.014.7596.4 40-94
40.4.25 - Position of air conditioner wiring connectors 40-95
40.4.26 - Cab earth wiring - 0.015.0031.4 40-96
40.4.27 - Positions of cab earth wiring connectors 40-97
40.4.28 - Worklights-number plate light- flashing light - 0.014.7595.4 40-98
40.4.29 - Positions of worklight, number plate and flashing light wiring connectors 40-99
40.4.30 - Flashing light wiring - 0.014.7591.4 40-101
40.4.31 - Positions of flashing light wiring connectors 40-101
40.4.32 - Windscreen wipers - 0.014.7598.4 40-102
40.4.33 - Positions of windscreen wiper wiring connectors 40-103
40.4.34 - Radio wiring - 0.014.7600.4 40-104
40.4.35 - Positions of radio-loudspeaker wiring connectors 40-105
VIII
0 - Introduction
0-1
Introduction
0.1 - Introduction
The purpose of this workshop manual is to provide instruction for repair technicians and a practical guide to improving the quality
of repairs. This manual enables repair technicians to acquire a thorough knowledge of the machine, indicating the correct methods
for fault diagnosis, for working in safety and for accurate dimensional checks and visual inspections. The instructions also indicate
the products to use, the tightening torques and the adjustment data. The technical material contained in this manual is reserved to
Authorised Dealers and Service Centres who will be duly informed of any technical changes to the machines in question through the
issue of documents regarding modifications, updates and supplements for optional equipment. All technicians and their colleagues
are expressly forbidden from reproducing any part of this manual in any form or from communicating the contents to third parties
without the express written permission of the Manufacturer, who remains the sole owner of this document with all rights reserved in
accordance with applicable laws.
0.1.1 - Safety notes
To ensure that machines entrusted to Authorised Service Centres for repair or overhaul continue to function correctly, it is very impor-
tant that all repair work is carried out in the prescribed manner. The procedures for checks and repairs indicated in this manual are
safe and effective. Some of the operations described require the use of special tools and equipment; these tools have been specifally
designed for the intended purpose and may be ordered directly from the Manufacturers. DO NOT USE MAKESHIFT TOOLS; not
only is there a risk of personal injury, but such tools are rarely suited to the purpose for which they are used. In potentially hazardous
situations, always give priority to personal safety and take the necessary actions to eliminate the danger
0.1.2 - General safety rules
l Even if you have a thorough knowledge of the machine as regards its components, operation and controls, always take spe-
cial care when carrying out the following operations; Remember that the machine you are working on is in need of repair or
overhaul and consequently may not always behave as expected.
l Before starting work, clean the tractor thoroughly to remove all mud, dust and road dirt. Also clean the cab to remove all traces
of oil, snow and ice from the access steps and grab rails.
l When climbing up to or down from the cab, always ensure you maintain three points of contact at a time (foot or handholds)
in order to keep your balance and prevent accidental falls.
l Always take special care when carrying out fault diagnosis operations; these operations often require two persons, who must
never stand in front of the wheels when the engine is running.
l When carrying out checks and repairs, wear close-fitting clothing, safety goggles and protective gloves that are suitable for
the task (cleaning, draining fluids, repairs). When working near moving parts, long hair should be gathered up and tied back
safely under a cap to prevent the risk of entanglement and severe injury.
l Do not allow anyone who is not directly involved in the work to come near the tractor; ensure that they remain at a safe dis-
tance.
l Keep well clear of moving parts; when the engine is running, some moving parts are not easily visible and therefore present a
risk of entanglement, even if protected by safety guards.
l Ensure that the area is well ventilated before starting the engine in order to avoid the formation of dangerous concentrations
of toxic gases; always connect suitable fume extraction equipment to the exhaust pipe.
l Do not start the engine with the safety guards removed under any circumstances; all repair and adjustment operations must
be carried out with the engine stopped.
l Do not top up fuel, oil or coolant levels when the engine is running.
l Never smoke and ensure there are no naked flames nearby when topping up fuel or oil. Always remove the battery from the
machine before recharging.
l Before checking or removing the battery, stop the engine and remove the key from the starter switch.
l Remove the battery and recharge in a well-ventilated area where the temperature exceeds 0C.
l When checking or recharging the battery, do not smoke or allow naked flames in the vicinity as the hydrogen gas given off by
the battery is highly explosive.
l The liquid (electrolyte) contained in the battery is very harmful if it comes into contact with the skin and the eyes; for this rea-
son, always wear gloves and safety goggles with side shields when checking or topping up the battery. Should any electrolyte
accidentally come into contact with your skin, wash the affected areas immediately with plenty of fresh water; if electrolyte
comes into contact with your clothing, this should be removed as soon as possible. In case of accidental ingestion of electro-
lyte, drink copious amounts of water, milk or vegetable oil and take antacids such as magnesium, bicarbonate, etc. and seek
medical attention immediately.
l Before working on the electrical systems, always disconnect the battery terminals.
0-2
Introduction
DANGER
Always disconnect the negative lead (--) before the positive lead (+); when re-connecting the battery on completion of
the work, first connect the positive terminal (+) and then the negative (--).
l Before carrying out any arc welding (permitted only on implements attached to the machine) always disconnect the battery
terminals and unplug all the connectors of the electronic control units and the alternator.
l When topping up lubricants, always wear suitable protective gloves.
l Do not wear clothing contaminated by engine or hydraulic oil; prolonged contact with the skin can be harmful and may cause
allergic reactions.
l Used engine oil and hydraulic oil must be disposed of properly; recover used lubricants and dispose of them in accordance
with the applicable regulations.
l Before carrying out any work on the hydraulic or pneumatic systems, discharge all residual pressure from the circuits.
l Before carrying out any work on the hydraulic system or engine, allow the oil and engine coolant to cool down.
l When removing and refitting certain assemblies, it will be necessary to support the tractor; use stands, jacks or blocks capable
of supporting the weight and arrange them in a triangular pattern to prevent the machine from overturning.
l To lift heavy components, use a hoist or crane. Check that wire ropes, chains or fibre slings are not worn and that hooks are
not damaged.
l Always use lifting equipment of suitable capacity for the weight of the components to be removed. Ensure lifting equipment is
attached correctly.
l When lifting or supporting an assembly or component, manoeuvre the parts slowly and carefully to avoid swinging movements
or collision with other components.
l Never work on components suspended from a hoist or crane.
l When removing the retaining bolts of a component that could fall, always leave two opposing bolts in place for safety; before
removing these last two bolts, attach the component to suitable lifting equipment or position support blocks.
l Any oil or fuel spilled during removal or dismantling operations should be cleaned up as soon as possible to prevent the risk
of slipping and fire.
l When refitting electrical wiring looms and wires, ensure that they are properly secured with their original retaining straps or
brackets to prevent the possibility of damage caused by vibration.
l Never insert your fingers or hands to check the alignment between fixing holes in components; always use a suitable dowel
of soft material.
l When refitting assemblies or components, always use the specified tightening torques; the tightening torques indicated in the
paragraphs regarding assembly/refitting operations have been determined through experimentation and must be scrupulously
adhered to.
l When refitting parts that are subject to vibration or that rotate at high speed, take particular care when carrying out final instal-
lation checks.
0-3
Introduction
Precautions for refitting operations
l Tighten nuts and screws to the specified tightening torques.
l When refitting flexible pipes and cables, take care not to twist or tangle them.
l Always fit new seals, O-rings, split pins and safety stop rings; make sure that the ends of the cotter pins are separated and
bent back so that the pin cannot be withdrawn from the hole.
l Ensure that circlips are correctly installed in their seatings.
l When applying threadlocking compound, first clean the part to remove all oil and grease, then cover the thread evenly apply-
ing a few drops of the compound.
l When applying sealant, first clean the surface removing all traces of oil and grease and check for dirt or indentations, then
apply the sealant evenly making sure that it forms a continuous film around any fixing holes.
l Clean all parts, removing dirt, oxidisation, carbon deposits, burrs and indentations.
l Coat all moving parts with a thin film of engine oil.
l When reconnecting electrical wiring connectors, first remove all traces of oil, dust and water from the inside of the connector
and then push the two halves together firmly; connectors with locking tabs should be pushed together until the tab engages
the keeper.
l Bolt down flanged fittings evenly, tightening the screws gradually in a crosswise pattern.
Precautions to be taken on completion of removal/refitting operations
l If coolant has been drained from the engine, refit the drain plug and pour in new coolant to the correct level. Start the engine
to circulate the coolant and then check the level again and top up.
l After removing hydraulic components, top up the hydraulic oil to the specified level. Start the engine to circulate the oil in the
hydraulic circuits and then recheck the level and top up as necessary.
l After having removed a variable displacement pump, connect the drain pipe and fill the pump casing with oil through the filler
hole provided.
l Grease stub axle housings, cylinder pivot mountings and drive shafts thoroughly after assembly.
l The lifting hook should be attached to the central part of the rope or sling; if the hook is attached near the ends of the rope/
sling, this could cause the load to slip during lifting.
l Never lift a heavy load using a single rope; always use two or more symmetrically arranged ropes.
0-4
Introduction
DANGER
Suspension of a load from a single rope could cause the load to start rotating and consequently cause the rope
strands to untwist or the load to slip; this could lead to serious injury.
l Never lift a heavy load when the two legs of the ropes form a wide angle. the permitted load (kg) decreases in inverse propor-
tion to the angle of suspension; the table below indicates how the permitted load varies according to the angle of suspension
for two 10 mm ropes each with a load capacity of 1000 kg.
Fig. 1
The tightening torques indicated below refer to screws and nuts assembled without lubrication and, where applicable, with anaerobic
threadlocking compound. the values apply to tightening on steel or cast iron components; for soft materials such as aluminium, cop-
per, plastic, sheet metal or panels, the indicated tightening torques must be reduced by 50%.
Table 2
BOLT SIZE BOLT CLASS
8.8 10.9 12.9
Nm lb.ft. Nm lb.ft. Nm lb.ft.
M6x1 8.0 8.8 5.9 6.5 11.8 13.0 8.7 9.6 13.8 15.2 10.2 11.2
M8x1.25 19.4 21.4 14.3 15.8 28.5 31.5 21.0 23.2 33.3 36.9 24.5 27.2
M10x1.5 38.4 42.4 28.3 31.2 56.4 62.4 41.6 46.0 67.4 74.4 49.7 54.8
M12x1.75 66.5 73.5 49.0 54.2 96.9 107 71.4 78.9 115 128 84.8 94.3
M14x2 106 117 78.1 86.2 156 172 115.0 126.8 184 204 135.6 150.3
M16x2 164 182 120.9 134.1 241 267 117.6 196.8 282 312 207.8 229.9
M18x2.5 228 252 168.0 185.7 334 370 246.2 272.7 391 432 288.2 318.4
M20x2.5 321 355 236.6 261.6 472 522 347.9 384.7 553 611 407.6 450.3
M22x2.5 441 487 325.0 358.9 647 715 476.8 527.0 751 830 553.5 611.7
M24x3 553 611 407.6 450.3 812 898 598.4 661.8 950 1050 700.2 773.9
M27x3 816 902 601.4 664.8 1198 1324 882.9 975.8 1419 1569 1045.8 1156.4
0-5
Introduction
FINE M8x1 20.8 23.0 15.3 17.0 30.6 33.8 22.6 24.9 35.8 39.6 26.4 29.2
M10x1.25 40.6 44.8 29.9 33.0 59.7 65.9 44.0 48.6 71.2 78.6 52.5 57.9
M12x1.25 72.2 79.8 53.2 58.8 106 118 78.1 87.0 126 140 92.9 103.2
M12x1.5 69.4 76.7 51.1 56.5 102 112 75.2 82.5 121 134 89.2 98.8
M14x1.5 114 126 84.0 92.9 168 186 123.8 137.1 199 220 146.7 162.1
M16x1.5 175 194 129 143 257 285 189.4 210.0 301 333 221.8 245.4
M18x1.5 256 282 188.7 207.8 375 415 276.4 305.9 439 485 323.5 357.4
M20x1.5 355 393 261.6 289.6 523 578 385.5 426.0 611 676 450.3 498.2
M22x1.5 482 532 355.2 392.1 708 782 521.8 576.3 821 908 605.1 669.2
M24x2 602 666 443.7 490.8 884 978 651.5 720.8 1035 1143 762.8 842.4
Fittings
The tightening torques indicated below refer to fittings assembled on any material.
Table 3
MET- Straight end fittings T end fittings L end fittings 90 end fittings
RIC
Thread size Wrench Torque Nm Wrench Torque Nm Wrench Torque Nm Wrench Torque Nm
10% 10% 10% 10%
M10x1.25 17 14 14 14 14 14 14 14
19 14 17 14 17 14
M12x1.25 19 30 17 30 17 30 17 30
M14x1.5 19 40 19 40 19 40 19 40
M16x1.5 22 48 22 48 22 48 22 48
M18x1.5 24 58 24 58 24 58 24 58
M20x1.5 27 65 27 65 27 65 27 65
M22x1.5 30 73 30 73 30 73 30 73
M26x1.5 36 95 36 95 36 95 36 95
M27x2 36 100 36 100 36 100 36 100
M33x2 41 160 41 160 41 160 41 160
M42x2 50 250 50 250 50 250 50 250
M48x2 60 305 60 305 60 305 60 305
G 1/8 17 13 14 13 14 13 14 13
19 13
G 1/4 19 37 19 37 19 37 19 37
22 37
G 3/8 24 53 24 53 24 53 24 53
G 1/2 27 73 27 73 27 73 27 73
30 73
G 3/4 36 100 36 100 36 100 36 100
G 1 41 160 41 160 41 160 41 160
46 160
G 1 1/4 50 250 50 250 50 250 50 250
G 1 1/2 60 305 60 305 60 305 60 305
Plugs
Table 4
Hex plugs Threaded plugs with hex socket head
0-6
Introduction
MET- M6x1 10 10
RIC M8x1 13 12
M10x1 13 14 5 14
M10x1.25 13 14
M10x1.5 13 14
M12x1.25 17 30
M12x1.5 17 30 6 30
M12x1.75 17 30
M14x1.5 19 40 6 40
M14x2 19 40
M16x1.5 22 48 8 48
M16x2 22 48
M18x1.5 17 58 10 58
M18x2.5 17 58
M20x1.5 19 65
M22x1.5 12 73
M24x1.5 22 80 12 80
M24x2 22 80
M27x2 22 100
M28x1.5 17 110
M30x1.5 22 130
M32x1.5 19 150
M35x1.5 22 180
M40x1.5 24 225
G 1/8 14 13
G 1/4 19 37
G 3/8 22 53
G 1/2 19 73
G 5/8 22 85
G 3/4 22 100
G 1 22 160
Fittings with seal at 37
Table 5
0-7
Introduction
Fittings for pipes with banjo union
These tightening torques refer to tightening the fitting with new copper sealing washers.
Table 6
Unions for one-way fittings Unions for three-way fittings Unions for four-way fittings
0-8
Introduction
DEGREASERS Loctite 703 Product used for degreasing and cleaning parts prior to applica-
AND ACTIVATORS tion of Loctite anaerobic products; after drying, promotes uniform
curing of threadlockers
Loctite 747 Product used specifically for treatment of passive metals prior to
use of slow-cure anaerobic threadlockers (series 5 and 6). Can
also be used to increase cure speed at low temperatures or in ap-
plications where there are large gaps between the parts.
SEALANTS (for Loctite 510 Colour: red Super-rapid anaerobic sealant for sealing between rigid metal
faces and fittings) faces; can eliminate the need for conventional gaskets as it can
fill gaps up to 0.4 mm. Does not shrink and therefore fasteners
do not need re-tightening to specified torque values after curing.
Loctite 542 Colour: Brown Anaerobic product used as a liquid sealant for threaded fittings
up to 3/4 gas; rapid curing and parts may be disassembled with
ordinary tools.
Loctite 554 Colour: red Anaerobic sealant and locking compound used for sealing cool-
ing and industrial fluid circuits. Slow curing, also suitable for use
on non-ferrous alloys
Loctite 572 Colour: White Anaerobic sealant and locking compound used for sealing pipes
and threaded fittings up to 2 in diameter. Very slow curing on
most metal surfaces.
Loctite 573 Colour: green Thixotropic anaerobic product used for sealing joints between
metal faces. Ensures total contact between surfaces with maxi-
mum tolerance of 0.10 mm, filling microvoids caused by flatness
errors. Very slow curing on most metal surfaces and requires
prior application of an activator.
Loctite 576 Colour: brown Anaerobic product used as a liquid thread sealant for large diam-
eter threaded fittings (up to 2). Very slow curing; also suitable for
non-ferrous alloys and parts requiring subsequent removal.
INSTANT ADHE- Loctite 401 Colour: colourless Cyanoacrylate instant adhesive suitable for bonding a wide range
SIVES of acidic and porous materials including, ceramics, wood, rub-
ber and plastic (excluding polyolefin). Curing takes place in a few
seconds as an effect of the condensed humidity present on the
surfaces to be bonded, and is independent of environmental con-
ditions.
Loctite 495 Colour: colourless Cyanoacrylate instant adhesive suitable for bonding a rubber,
plastics and metal in any combination.
SEALANTS SILI- Silastic 738 (Dow Corning) Colour: milky One-part silicone adhesive/sealant, non dhrinking, ready for use.
CONE white Cures on exposure to air to form a rubbery solid and obviates the
need for conventional seals on flexible joints, filling gaps greater
than 1 mm.
Dirko Transparent Colour: transparent One-part silicone adhesive/sealant, shrinking, ready for use.
Cures rapidly when exposed to humidity in the air to form a rub-
bery solid; resistant to high temperatures.
SEALANTS POL- Betaseal HV3 (Gurit Essex) Colour: black Polyurethane prepolymer based adhesive/sealant, high viscosity,
URETHANE suitable for permanent, high-strength flexible bonding. Slow cur-
ing, used for bonding glass to frames, wire mesh, metal plates,
etc. surfaces must be degreased with primer.
0-9
Introduction
RETAINING COM- Loctite 601 Colour: fluorescent green Anaerobic, fast-curing, high-strength adhesive. Suitable for seal-
POUNDS ing and retaining cylindrical assemblies with gap clearances of
up to 0.10 mm; used for retaining rotors, gears, bearings, pulleys,
bushes etc. on shafts.
Loctite 638 Colour: fluorescent green Anaerobic structural adhesive, quick-curing, very high strength;
suitable for bonding cylindrical parts in non-ferrous alloys.
Loctite 648 Colour: fluorescent green Anaerobic structural adhesive, quick-curing, high-strength; suit-
able for bonding cylindrical parts, permanent retention of thread-
ed parts, sealing of refrigeration systems, retention of bearings,
etc. Alternative to Loctite 601 in high-temperature applications.
Loctite 986/AVX Colour: Fluorescent red Anaerobic sealant/retaining compound for metal cylindrical parts.
Slow-curing, high-strength, heat-resistant and resistant to chemi-
cal attack. Parts must be first treated with an activator.
LUBRICANTS Grease (NLGI 2 EP ASTM D217: 265/295) Multi-purpose Lithium grease used for lubrication of seals, to pre-
vent oxidization and to facilitate assembly operations.
Molikote (Dow Corning) Anti-wear compound, contains Molybdenum bisulphate, used
neat or diluted with engine oil for assembly of main engine bear-
ings.
Vaseline Neutral pH compound used to protect battery terminals against
oxidization and corrosion.
Engine oil 10W - 30 Used to dilute Molikote anti-wear lubricant during assembly of
main engine bearings.
0-10
Introduction
m x 1.197 = Sq.yard
cm x 0.061 = Cu.in.
m x 0.035 = Cu.ft
m x 1.311 = Cu.yard
litres x 0.220 = Imp.gall.
litres x 0.264 = US gall.
litres x 1.762 = pint
litres x 0.880 = quart
,/min x 0.2642 = US.gpm
kg x 35.25 = oz.
kg x 2.203 = lb.
kgm x 7.233 = lb.ft.
kg/m x 0.056 = lb.in.
kg/cm x 14.22 = psi
kg/, x 10.00 = lb./Imp.gal.
kg/, x 8.333 = lb./US.gal.
kg/m x 0.062 = lb./cu.ft.
Nm x 0.737 = lb.ft.
bar x 14.503 = psi
0-11
Introduction
0-12
10 - Technical
characteristics
10-1
Technical characteristics
10.1 - Transmission
10.1.1 - Transmission
Introduction
l The tractor in this series are equipped with a 4-speed transmission with forward/reverse shuttle and three speed ranges. The
main gearbox and the forward/reverse shuttle are synchronised, while the 3-speed range gearbox is not synchronised.
l The rear transmission casing also houses the drive train for the rear PTO, which is supplied in a single version (540-1000-ground-
speed). The rear PTO is of the mechanical type with non-synchronised gears. The PTO can also be supplied with a mid-
mounted output shaft that is only enabled when the 1000 rpm PTO speed is selected.
10-2
Technical characteristics
Fig. 4 - 1st gear, forward drive and high range (H) selected
10-3
Technical characteristics
Fig. 5 - 1st gear, reverse drive and low range (L) selected
Fig. 6 - 3rd gear, forward drive and medium range (M) selected
10-4
Technical characteristics
Clutch housing
10-5
Technical characteristics
Gearbox and shuttle assembly
10-6
Technical characteristics
4WD - Range gears assembly
10-7
Technical characteristics
Pinion and differential assembly
10-8
Technical characteristics
540 PTO
10-9
Technical characteristics
540-750 PTO
10-10
Technical characteristics
540-750 PTO and Mid PTO dt1
10-11
Technical characteristics
540-750 PTO and Mid PTO dt2
10-12
Technical characteristics
10.2 - Rear axle
10.2.1 - Brakes and rear axle assembly
10-13
Technical characteristics
10.3 - Front axle
10.3.1 - Front axle
Characteristics and components
10-14
Technical characteristics
Steering cylinder
10-15
Technical characteristics
10-16
Technical characteristics
10.4 - Hydraulic system
10.4.1 - Gear pump
10-17
Technical characteristics
10.4.2 - Differential lock control assembly
10-18
Technical characteristics
10-19
Technical characteristics
Fig. 22 - Function
Operation
l The pressurised oil from the power steering reaches chamber P and chamberA through passage B. If there is no demand from
the actuators, the oil stays in chamber P where the pressure starts to increase. When the force exerted on the spool (1) by
the oil pressure in chamber A exceeds the force of the spring (2), the spool shifts downwards, thereby connecting chamber
P with chamber L and regulating the pressure in chamber P1 to 12 bar. Surplus oil is thus directed through chamber L to the
gearbox/shuttle assembly where it is used for lubrication
l If the solenoid valve (3) is not energised, the oil stops in chamber P1 and chamber U is connected to chamber T and the oil
is returned to tank.
l If the solenoid valve (3) is energised, (as shown in the drawing), chamber P1 is connected to chamber U and oil is sent to the
control piston of the front differential lock.
10-20
Technical characteristics
Function
The steering circuit sends oil to the power steering, which in turn, according to the request from the operator, sends oil pressure to
the steering circuit.
Fig. 23 - Function
Operation
Gear pump (1) draws in oil (through filter (2)) from the transmission casing and sends it to the power steering (3). The excess oil not
used by the power steering (3) is sent to the differential lock control (5) and used to operate the front axle differential lock piston (6)
and for lubrication of the gearbox and shuttle assembly (7). When the operator turns the steering wheel, part of the oil supplied from
the pump (1) is sent to the the steering cylinder (4) which steers the tractor.
10-21
Technical characteristics
10.4.4 - Power steering valve
10-22
Technical characteristics
10.4.5 - Remote control valve
10-23
Technical characteristics
10-24
Technical characteristics
Hydraulic lift control valve
10-25
Technical characteristics
10-26
Technical characteristics
Fig. 29 - Function
Operation
l The lift is in neutral position when the the oil pressure from pump (1) reaches line A. As all the passages are closed, the pres-
sure increases and when the force exerted on the enabling valve (2) overcomes that of the spring (3), the valve (2) shifts to the
right to allow oil to flow in line B and on to the gearbox/shuttle assembly where it is used for lubrication (4). To prevent sudden
changes in pressure, a pressure control valve (5) is installed on line B, to limit the lubrication oil pressure.
10-27
Technical characteristics
necting line F with line I (drain), thereby allowing the pressure to reduce in line F.
10-28
Technical characteristics
(10) with line F. Consequently the pressure in chamber M is decreased and the force exerted on the piston (8) by the
pressure in chamber N pushes the valve (10) to right, thereby connecting line P with line F and allowing the oil to flow
and the lift to be be lowered. Valve (11) is used to regulate the rate of drop; when moved downwards, it limits the flow
of oil between port T and line P.
10-29
Technical characteristics
10-30
Technical characteristics
Fig. 33 - Raising
10-31
Technical characteristics
10-32
20 - Calibrations and
electronic diagnosis
20-1
Calibrations and electronic
diagnosis
20.1 - Diagnostic tool screens
20.1.1 - Baruffaldi electromagnetic clutch
Baruffaldi electromagnetic clutch control unit
Introduction
This control unit is an integral part of the system used to reduce the noise level of the tractors. The main characteristics of the control
unit are:
l Automatic operating mode
l Coolant temperature control
l Air temperature control
l Coolant thermostat
Description
The Baruffaldi system is comprised of the following elements:
l Electromagnetic clutch
l Sensor to measure ambient temperature sensor inside the control unit
l Coolant temperature sensor
l Coolant thermostat
l Connection to alarm warning light on instrument
l Electronic control unit
l Wiring
The electronic control unit uses the following inputs/outputs to control the electromagnetic clutch:
l Analogue input for coolant temperature sensor signal
l Digital input for coolant thermostat signal
l Digital input for alarm 4 enabling signal
l An output for control of the electromagnetic clutch
l 1 output for control of the alarm warning light
Below is the electrical control diagram of the electronic control unit 2.8519.035.0.
20-2
Calibrations and electronic
diagnosis
Fig. 34
20-3
Calibrations and electronic
diagnosis
Fig. 35
20-4
Calibrations and electronic
diagnosis
Operation
The operation of the control unit is based mainly on two temperature sensors. The air temperature sensor reading is used to deter-
mine which coolant temperature threshold to apply.
Below is the operating flow chart.
Fig. 36
l E Off = electromagnetic clutch off
l E On = electromagnetic clutch on
l Po = power on
l Se = summer thresholds
l Si = winter thresholds
20-5
Calibrations and electronic
diagnosis
l S Off = warning light off
l S On = warning light on
l Ta = air temperature
l T On = thermostat on
l Tw = coolant temperature
l Twl = threshold off
l Twh = threshold on
The following graph shows the threshold values used by the control unit.
Fig. 37
l T1 = coolant temperature
l T2 = ambient temperature
l T3 = winter temperature for non-intervention of control unit
l T4 = winter temperature for intervention of control unit
l T5 = summer temperature for non-intervention of control unit
l T6 = summer temperature for intervention of control unit
l T7 = low ambient temperature
l T8 = high ambient temperature
The thermostat ensures safety in the event of a malfunction of the coolant tempearture sensor. If the thermostat is tripped both the
electromagnetic clutch and the alarm warning light will be activated. If the electromagnetic clutch is activated due to the coolant tem-
perature being above the threshold value, then the alarm warning light is not activated. In this application the oil temperature sensor
is not used. As an option, the air temperature sensor located inside the control unit can be used to check that the unit is operating
within its limits. If the temperature exceeds 80C, an alarm is signalled (see diagnostics). The option can be enabled by connecting
pin 9 (DIAG) to 12V.
Tolerance limits
Below are described the maximum tolerance limits calculated for the temperature sensors used.
l Air temperature sensor
The sensor in question is an NTC decvice installed inside the control unit. The NTC sensor has a specific tolerance of 2% while the
pull-up resistor has a specific tolerance of 1%. The sum of the tolerances makes for a maximum error of 3%, which in terms of
the temperatures in consideration, is equivalent to a maximum error of 0.5C.
l Coolant temperature sensor
20-6
Calibrations and electronic
diagnosis
This sensor, which is installed on the engine, has a maximum error of 1C . The pull-up resistance in the control unit has a specific
tolerance of 1%. The following table indicates the minimum and maximum threshold values in accordance with the tolerance limits
obtained with an 8 bit converter (2.8519.035.0).
Table 14
Nominal thresholds (C) Minimum thresholds (C) Maximum thresholds (C)
82 81 83
87 85 88
90 89 92
95 93 96
The temperatures detected by the control unit will always between contained within the minimum and maximum threshold values
according to tolerance trends. It is necessary to add 1C to these thresholds due to the error of the microprocessors analogue/digital
converter. Consequently the maximum possible error is 3C.
The use of a microprocessor with 10-bit converter will improve sensor tolerance limits, bringing them to within -1.5C +1C. The
following table indicates the minimum and maximum threshold values in accordance with the tolerance limits obtained with an 10 bit
converter (2.8519.056.0).
Table 15
Nominal thresholds (C) Minimum thresholds (C) Maximum thresholds (C)
82 80.5 83
87 86 88
90 89 91
95 94 96
The error caused by the converter increases the total by 0.5C, bringing the maximum error to -2C +1.5C.
Diagnostics
The control unit monitors the coolant temperature sensor connection and its own operating temperature. If a fault is detected in the
coolant temperature sensor, the control unit activates the electromagnetic clutch.
The following table lists the various fault conditions that generate alarms.
Table 16
Error code Notes Possible cause of the fault
2 Coolant temperature >130C or short to Short to earth of sensor/control unit con-
earth nection - Sensor faulty - Control unit faulty
3 Coolant temperature <-30C or sensor not Sensor/control unit connection open - Sen-
connected sor/earth connection open - Sensor faulty
- Control unit faulty
4 Control unit temperature >80C Temperature in engine compartment high -
Control unit faulty
IMPORTANT
Alarm 4 is normally disabled, and therefore must be enabled in order to be operational (see Operation).
The condition is considered a fault if it lasts for at least 0.5 seconds. If the cause of the alarm is removed the alarm code will no
longer be displayed.
Faults are signalled by flashing codes on the indicator light. The code comprises a sequence of flashes identifying the type of fault,
with a duration of 0.2 seconds repeated continuously every 1.2 seconds. Below is an example display of alarm code 2.
20-7
Calibrations and electronic
diagnosis
Fig. 38
20-8
Calibrations and electronic
diagnosis
The ECU implements the correct system management strategy in relation to this state.
Reverse input
This input is used to activate an intermittent audible warning signal, with a duty cycle of 0.5 seconds ON and 0.6 seconds OFF,
indicating that reverse is selected.
This input is activated with a 12V signal, and the relative function is only enabled with the ignition ON.
Indicator lamp output
This output is used to indicate the state of the handbrake in relation to the ignition switch state and the seat sensor state.
System function
The ECU is powered directly by the battery and is always on, in two possible modes:
l key OFF mode,
l key ON mode.
WARNING
In both modes, the handbrake released state is indicated by a continuous audible warning signal and by the indicator
lamp flashing with a duty cycle of 0.5 seconds ON and 0.5 seconds OFF.
WARNING
If the handbrake released audible warning signal and indicator lamp are active when changing from key OFF to key
ON state and vice versa, both signals continue without interruption unless the conditions necessary for activation no
longer exist in the new ignition switch state.
Key OFF
In this ignition switch state, the ECU monitors the handbrake state only.
The ECU monitors the following two conditions:
l Transitions between key ON / key OFF,
l Transitions between handbrake active/deactivated.
In this mode, the ECU implements low power consumption strategies to keep maximum current absorption within 2mA.
Transition from key ON -> key OFF
When the ECU detects a transition in the state of the ignition switch from ON to OFF, it queries the state of the handbrake and,
if the handbrake is not engaged, indicates this condition with an audible warning signal [buzzer] and a visual warning [warning lamp
output] for 10 seconds. The warning signals are stopped if the handbrake is applied.
Key OFF mode
When the machine is switched off, the ECU monitors the state of the handbrake only, and activates the audible/visual warning signals
for 10 seconds whenever there is a transition in the handbrake state from active to deactivated. The warning signals are stopped if
the handbrake is applied.
Key ON
In this ignition switch state, the ECU monitors all input signals. The main function of the ECU in this mode is to verify whether the
operator is seated in relation to the handbrake state.
When the ECU detects that the handbrake is released without the operator seated, it activates the audible [buzzer] and visual [war-
ning lamp] warning signals for as long as the conditions persists - specifically, until the handbrake is applied or the operator sits in
the seat.
The state of the operator seated signal is verified every 200 mS.
The operator not seated state is recognised after a period of 2 seconds.
The handbrake state is always recognised with a latency of 0.5 seconds.
Reverse input management
If the reverse input is activated, the ECU activates the buzzer with priority over any other internal request.
The ECU restores normal buzzer management one second after the signal is deactivated.
If the reverse signal is activated while the audible/visual handbrake released signals are active, the handbrake released warning
sound is stopped and superseded by the reverse warning, while the visual handbrake released warning continues.
The recognition time for the ON/OFF signal is 0.1 seconds.
20-9
Calibrations and electronic
diagnosis
Sensor type selection input management
The ECU identifies the state of this input to determine the type of sensor connected and manage the relative signal correctly.
If the input is OPEN, an analogue sensor is used, whereas if the input is connected to +12V, a digital sensor is used [see previous
chapter].
This input is monitored continuously with a recognition time of 0.2 seconds.
When the ECU is powered up for the first time, it will not be functional until the type of seat sensor connected has been recognised.
Seat sensor management
The ECU uses the seat sensor signal to verify whether or not the operator is seated. The ECU monitors voltages for both digital and
analogue sensors.
** Digital sensor diagnosis
The ECU recognises an operator seated state if the voltage is 1.0V.
A voltage of 4.0V indicates that the operator is not seated.
Any voltage between these two values is considered a fault and generates an intermittent audible alarm signal consisting of 5 pulses
with a duty cycle of 0.2 seconds ON / 0.2 seconds OFF repeated at 1 second intervals. The audible warning signal remains active
until the fault is rectified.
** Analogue sensor diagnosis
When an analogue sensor is used, if a voltage other than those associated for the operator seated and operator not seated states is
measured, the ECU uses the buzzer to indicate the respective diagnostic code as follows:
l Short circuit to ground [Vin < 0.5v] = 3 pulses of 0.2 seconds ON/ 0.2 seconds OFF + 1 second pause.
l Short circuit to +12V or sensor not connected [Vin > 4.5v]: 2 pulses of 0.2 seconds ON / 0.2 seconds OFF + 1 second
pause.
l Values not within valid range: 4 pulses of 0.2 seconds ON / 0.2 seconds OFF 1 second pause.
The diagnostic signal is stopped as soon as the seat sensor signal returns within valid ranges.
ECU powered up for first time
When the ECU is connected to the battery for the first time, irrespective of the states of any of the inputs, it produces the following
audible signal sequence:
l 0.5 seconds ON
At the end of the sequence, the ECU starts functioning in normal operating mode, in relation to the states of the inputs.
The diagnostic signal is stopped as soon as the seat sensor signal returns within valid ranges.
20-10
Calibrations and electronic
diagnosis
Functional diagram
K30
1
SELECT 4 Hand Brake
(!) Connect to K15 for digital sensor (!) Light
6
Key K15
7
8
Analogic
2
seat sensor
GND
20-11
Calibrations and electronic
diagnosis
20-12
30 - Method of intervention
30-1
Method of intervention
30.1 - B0 - Engine
30.1.1 - PREPARATION FOR DISASSEMBLY
Precautions
This section outlines basic precautions recommended by Mitsubishi that should always be observed.
Disassembly
1. Always use tools that are in good condition and be sure you understand how to use them before performing any job.
2. Use an overhaul stand or a work bench, where necessary. Also, use bins to keep engine parts in order of removal.
3. Parts must be restored to their respective components from which they were removed at disassembly. This means that all
parts must be set aside separately in groups, each marked for its component, so that the same combination or set can be
reproduced at assembly.
4. Pay attention to marks on assemblies, components and parts for their positions or directions. Apply marks, if necessary, to
aid assembly.
5. Carefully check each part or component for any sign of faulty condition during removal or cleaning. Clues as to how well part
is functioning are more easily revealed during removal or cleaning operations.
6. When lifting or carrying a part too heavy or too awkward for one person to handle, enlist the help of another person and, if
necessary, use a jack or other lifting equipment.
Assembly
l Wash all parts, except for oil seals, O-rings, rubber sheets, etc., with cleaning solvent and dry them with compressed air.
l Always use tools that are in good condition and be sure you understand how to use them before performing any job.
l Use only good quality lubricants. Be sure to apply oil, grease or sealant to parts as specified.
l Be sure to use a torque wrench to tighten parts for which torques are specified.
l Each time the engine is re-assembled, new gaskets and O-rings must be installed.
Draining engine oil
1. DANGER
Hot oil and components can cause serious personal injury.
Do not allow hot oil or components to come into contact with
skin.
To drain the oil, remove the drain plug from the oil sump.
Table 18
Draining coolant
1. Loose the drain plug on the right side of the engine block and allow the
coolant to drain.
Table 19
Fig. 41
30-2
Method of intervention
30.1.2 - Engine - Separation from the transmission
Removal
1. DANGER
Disconnect the lead from the battery negative terminal (-) and apply the parking brake.
Fig. 42
3. Drain off all the oil from the transmission.
Disconnect front differential lock pipe (2) and the two power steering pipes
(3).
Fig. 43
4. Disconnect the front PTO lube pipe (4) on the left-hand side.
Fig. 44
5. On both sides, remove silent block retaining nuts (5), remove the two lateral
fixing screws and remove footplates (6).
Fig. 45
30-3
Method of intervention
6. Remove cable support bracket (6) and disconnect throttle cables (7).
Fig. 46
7. On both sides, remove fixing screws (8) and remove tank frame (9).
Fig. 47
8. Loosen alternator drivebelt adjustment screw (10).
Fig. 48
9. Remove alternator drivebelt (11).
Fig. 49
30-4
Method of intervention
10. Disconnect the two alternator wiring connectors (12).
Fig. 50
11. Disconnect the outer cable (13) of the positive terminal of the starter motor.
Fig. 51
12. Remove retaining nut (14) and remove starter motor protection (15).
Fig. 52
13. Disconnect the cable (16) connected to the positive terminal of the starter
motor.
Fig. 53
30-5
Method of intervention
14. Remove nut (17) to release the inner cable from positive terminal (18).
Fig. 54
15. On the left-hand side, remove retaining nut (19) of the bracket of the cli-
mate control pipe bracket.
Fig. 55
16. Disconnect the two oil supply pipes (20) of the hydraulic services pump and
of the rear lift hydraulic pump.
m Remember to plug the ends of the pipes.
Fig. 56
17. Remove the two screws (21) and remove bracket (22) supporting the power
steering pipes.
Fig. 57
30-6
Method of intervention
18. Disconnect front wiring harness (23).
Fig. 58
19. Disconnect glowplug feed wire (24).
Fig. 59
20. Disconnect the two throttle cables (25).
Fig. 60
21. Loosen hose clamp (26) and disconnect fuel suction pipe (27) from the
pump.
m Remember to plug the end of the pipe.
Fig. 61
30-7
Method of intervention
22. Release front PTO wiring (28) from the retaining clips.
Fig. 62
23. Disconnect the two front PTO oil pipes (29).
Fig. 63
24. Disconnect front differential lock control pipe (30).
Fig. 64
25. Disconnect the two pipes (31) of the mid-mounted hydraulic couplers.
Fig. 65
30-8
Method of intervention
26. On th left-hand side, unscrew nut (32), remove fixing screws (33) and re-
move climate control pipe bracket (34).
m Recover the spacer and washers.
Fig. 66
27. Remove the two retaining screws (35), disconnect pipe (36) from front lift
valve and from the strap securing it to the bracket, then remove mid-mount-
ed hydraulic couplers (37) along with the support bracket.
Fig. 67
28. Position a stand (38) under the engine.
Fig. 68
29. Remove the seven screws (39) on the engine-clutch housing connection
flange.
Fig. 69
30-9
Method of intervention
30. Separate engine (40) from the transmission.
Fig. 70
Refitting
1. Refitting is the reverse of removal.
30.1.3 - Engine
Removal
1. DANGER
Disconnect the lead from the battery negative terminal (-)
and apply the parking brake.
Place one stand under the gearbox and one under the engine (1).
Fig. 71
2. Attach two hooks (2) to the lifting brackets provided on the engine.
Fig. 72
3. Attach a hoist to the engine and take the strain with the lifting ropes.
Fig. 73
30-10
Method of intervention
4. Remove the seven screws (3) securing the engine to clutch housing.
Fig. 74
5. Remove complete engine assembly (4).
Fig. 75
Refitting
1. Refitting is the reverse of removal.
Fig. 76
30-11
Method of intervention
Test
1. Move the control lever to the position to shut off the fuel supply. Remove all
the glow plugs from the engine. Install the compression test gauge on the
cylinder on which the compression pressure is to be measured. Turn the
engine over with the starter motor and read the pressure on the gauge at
the point the gauge needle stops.
m If the gauge reading is below the limit, proceed with engine overhaul.
m Test the compression on all the cylinders.
m The compression pressure varies with the engine rpm. For this rea-
son it is necessary to check engine rpm when testing cylinder com-
pression. Fig. 77
Table 20
30-12
Method of intervention
30.1.5 - engine block, crankshaft, pistons and sump
Fig. 79
30-13
Method of intervention
2. Removal of the gauze oil filter
Loosen the nut securing the gauze filter and remove the filter.
Fig. 80
3. Measuring thrust clearance for connecting rod big end.
Install the connecting rod to its cranking and tighten the cap nuts to the
specified torque. Measure the thrust clearance with a feeler gauge. If the
clearance exceeds the limit, replace the connecting rod.
Table 21
Fig. 82
5. Removal of the piston.
Turn the crankshaft to bring the piston to top dead centre. Push the piston
and connecting rod away from the crankshaft with the handle of a hammer
or similar tool until the piston rings are clear of the cylinder, then remove the
piston and connecting rod. Repeat the above operations for the remaining
pistons.
Fig. 83
30-14
Method of intervention
6. Measuring crankshaft end float.
Position a dial gauge in contact with the end of the crankshaft and measure
the end float. If the end float exceeds the limit, replace No. 3 flanged bear-
ing.
Table 22
Fig. 85
8. Removal of the crankshaft
Remove the crankshaft.
m Take care not to damage the bearings.
m Mark the main bearing shells so they can be refitted to their original
positions.
Fig. 86
9. Separating the piston from connecting rod.
Separate the piston from the connecting rod using the specific gudgeon
pin tool.
Fig. 87
30-15
Method of intervention
10. Insert the push rod of the tool into the small-end bearing bore in the piston
and, using an arbor press, drive out the gudgeon pin. Use the same gud-
geon pin tool to refit the connecting rod to the piston.
1 - Gudgeon pin.
2 - Arrow mark.
3 - Piston.
4 - Tool
5 - Connecting rod.
6 - Identification mark.
7 - Tool holder.
Fig. 88
11. m Do not attempt to drive out the gudgeon pin by hitting it. A gudgeon
pin which can only be removed using a greater force should be re-
newed.
Fig. 89
Inspection
30-16
Method of intervention
Fig. 91
2. Refitting the crankshaft.
Clean the crankshaft with cleaning solvent and blow dry with compressed
air. Attach a hoist to the crankshaft and hold it in a horizontal position. Care-
fully lower the crankshaft in position in the engine block. Lightly lubricate
the crankshaft journals with engine oil.
Fig. 92
30-17
Method of intervention
3. Refitting the main bearing caps.
Coat the mating surfaces of the rear main bearing cap and the engine block
with Three Bond 1212. Locate the main bearing caps. Make sure the num-
ber (arrow) on the main bearing cap is pointing towards the front of the
engine. Tighten down the main bearing cap bolts by hand.
Fig. 93
4. m Install the front and rear bearing caps so their end faces are even
with the end faces of the engine block.
Tighten the main bearing cap bolts gradually to the specified torque.
Table 23
Fig. 94
5. Make sure the crankshaft rotates freely without binding or catching. Mea-
sure the crankshaft end float. If the end float is incorrect, loosen the main
bearing cap bolts and then tighten them again.
Fig. 95
6. Refitting the the side seals.
Coat the side seals with Three Bond 1212. Insert the side seals between
the engine block and the front and rear main bearing caps and push in them
by hand as far as possible, with their rounded side toward the outside of
the engine block.
A - Side seals.
B - Rounded side.
Fig. 96
30-18
Method of intervention
7. Using a flat plate, push the seals into position, taking care not to bend them.
Fig. 97
8. Refitting the piston to the connecting rod.
Place the gudgeon pin tool (31A91-00100) in a hydraulic press. Position the
connecting rod on the tool and lubricate the small-end bore with engine oil.
Fig. 98
9. Position the piston on the connecting rod, making sure the identification
mark on the connecting rod is on the same side as the arrow on the piston
crown. Locate the gudgeon pin.
Fig. 99
10. Insert the end of the tool into the small-end bore in the piston and install the
gudgeon pin with the press.
m Observe the gauge of the press when installing the gudgeon pin. If
the force of the press exceeds 50 kgf (110 1bf) [490 N], stop install-
ing the pin and check that the bores in the piston and connecting rod
are properly aligned.
Fig. 100
30-19
Method of intervention
11. After assembling the piston and connecting rod, make sure the connecting
rod moves freely.
Fig. 101
12. Refitting the piston rings.
Using a piston ring pliers, install the piston rings on the piston.
m The piston rings must be installed with the side marked T toward
the top of the piston.
A - Top marking.
1 - Top compression ring.
2 - Second compression ring.
3 - Oil control ring.
Fig. 102
13. m The oil control ring must be installed with the ring gap positioned
180 to the expander spring joint.
A - Expander spring joint.
B - Oil control ring end gap.
Fig. 103
14. Refitting the piston-connecting rod assembly
Lubricate the piston and piston rings with engine oil. Position the piston
rings gaps so they are staggered from a direction parallel to, or transverse
to, the gudgeon pin. Install the big-end shell bearing (upper) in the connect-
ing rod, making sure the rear tab of the bearing engages the notch in the
connecting rod.
Turn the crankshaft until the crankpin for the piston and connecting rod to
be installed is at top dead centre. Hold the piston and connecting rod with
FRONT mark (arrow) on the the piston crown pointing towards the front
(timing cover side) of the engine.
1 - Oil control ring.
Fig. 104
2 - Front of engine.
3 - Top compression ring.
4 - Second compression 2 and oil control ring expander spring joint.
30-20
Method of intervention
15. Using a piston guide (commercially available), insert the piston and con-
necting rod in the cylinder from the top of the engine block.
m Do not hit the piston with a mallet to install the piston and connecting
rod. This will put force on the piston and connecting rod and cause
damage to the piston rings and crankpin.
Fig. 105
16. Refitting the big-end bearing cap.
Push the piston into position until the big end of the connecting rod is lo-
cates on the crankpin, then rotate the crankshaft through 180 while si-
multaneously pressing down on the piston crown. Install the lower big-end
bearing shell in the big-end bearing cap, making sure the tab on the rear of
the bearing shell engages the notch in the bearing cap. Finally, fit the big-
end the bearing cap on the connecting rod.
m Check that the identification number on the bearing cap matches the
number on the connecting rod.
m Check that the identification number on the bearing cap matches the
Fig. 106
number on the connecting rod.
A - Notches.
B - Cylinder number.
17. Tighten the big-end bearing cap nuts gradually to the specified torque.
Table 24
Check the thrust clearance for the connecting rod big end.
Fig. 107
18. Refitting gauze oil filter.
Lay the engine block with the underside (sump) facing upwards. Position
the gauze oil filter.
m The gauze oil filter must be positioned so that remains below the oil
level and clear of the sump.
Fig. 108
30-21
Method of intervention
19. Refitting the oil sump.
Clean the mating surfaces of the sump and engine block and coat them
with Three Bond 1207C.
Fig. 109
20. m Squeeze out a 4 mm (0.2 in.) bead bar of sealant (Three Bond) from
the tube and apply to the flange of the oil sump as shown.
Fig. 110
21. To obtain a 4 mm (0.2 in.) bead of sealant, cut the nozzle of the tube (A) as
shown in the figure.
Fig. 111
22. Tighten the bolts securing the sump to the engine block in a crisscross pat-
tern to the specified torque.
Table 25
30-22
Method of intervention
30.1.6 - Inspection of the engine monobloc
Check
1. Measure the bore at the top, middle and bottom points on axes A and B with
a cylinder bore gauge as shown in the figure.
m If the measured values are outside the specified limit, hone the cyl-
inder bores for oversize pistons.
Table 26
Fig. 115
30-23
Method of intervention
2. Measure the diameter of the crankpin as shown in the figure to obtain the
clearance between the crankpin and big-end bearing.
Table 29
m If the clearance still exceeds the limit, grind the crankpin to 0.25 mm
(0.0098 in.), 0.50 mm (0.0197 in.) or 0.75 mm (0.0295 in.) undersize
and use an undersize big-end bearing.
3. Table 30
Fig. 118
30-24
Method of intervention
5. Measure the diameter of the main bearing journal as shown in the figure (A)
to find the clearance between the journal and main bearing.
m If the clearance exceeds the limit, install a new bearing and check
the clearance again.
m If the clearance still exceeds the limit, grind the journal to 0.25 mm
(0.0098 in.), 0.50 mm (0.0197 in.) or 0.75 mm (0.0295 in.) undersize
and use an undersize main bearing.
Table 32
Fig. 121
30-25
Method of intervention
8. Remove the gear from the crankshaft using a gear puller.
m Do not remove the gear unless the gear or crankshaft is defective.
Fig. 122
9. Locate the Woodruff key in its seat in the crankshaft, then locate the gear,
aligning the slot with the key as shown in the figure (A).
Fig. 123
Fig. 124
3. Loosen lower screw (2) of alternator support.
4. Remove drivebelt (3).
Fig. 125
30-26
Method of intervention
Refitting - version without front PTO
Refitting is the reverse of removal.
Removal - version with front PTO
1. DANGER
Disconnect the lead from the battery negative terminal (-).
Fig. 126
3. Remove lower screw (2) of alternator support.
Fig. 127
4. Remove grub screw (4) securing the shaft.
Fig. 128
5. Remove the three flange fixing screws (5).
Fig. 129
30-27
Method of intervention
6. Move flange (6) forwards to create the necessary space to remove the
drivebelt.
Fig. 130
7. Remove drivebelt (3).
Fig. 131
Fig. 132
30-28
Method of intervention
3. Tension the drivebelt to obtain deflection of 10 to 12 mm at the mid-point of
the belt run between the crankshaft pulley and alternator (7).
m Re-adjust the tension after 50 operating hours if a new drivebelt is
fitted.
Fig. 133
Fig. 134
3. Remove drivebelt (2).
Fig. 135
30-29
Method of intervention
2. Remove grub screw (3) securing the shaft.
Fig. 136
3. Remove the three flange fixing screws (4).
Fig. 137
4. Move flange (5) forwards to create the necessary space to remove the
drivebelt.
Fig. 138
5. Loosen tensioner locknut (1).
Fig. 139
30-30
Method of intervention
6. Remove drivebelt (2).
Fig. 140
Fig. 141
3. Tension the drivebelt to obtain deflection of 10 to 12 mm at the mid-point of
the belt run between the crankshaft pulley and A/C compressor (6).
Fig. 142
30-31
Method of intervention
30.1.10 - Crankshaft pulley
Removal
1. Remove crankshaft pulley nut (1).
Fig. 143
2. Remove the alternator-fan drivebelt (2) and A/C drivebelt (3).
m Remove the crankshaft pulley nut before removing the alternator-
fan drivebelt and the A/C drivebelt as the tension of the drivebelts
helps oppose rotation of the crankshaft.
Fig. 144
3. Remove crankshaft pulley (3).
Fig. 145
30-32
Method of intervention
Refitting
Refitting is the reverse of removal.
30.1.11 - Flywheel bearing
Removal
1. Locate punch (1) on flywheel bearing (2).
Fig. 146
2. Tap the punch with a hammer to drive bearing (2) out of the flywheel.
Fig. 147
Refitting
Refitting is the reverse of removal.
30.1.12 - Timing gears and flywheel
30-33
Method of intervention
Fig. 149
30-34
Method of intervention
2. DANGER
When removing the flywheel, wear heavy gloves to avoid
hand injury.
Insert a safety rod (M12 x 1.25) in the threaded hole in the flywheel from
which the screw was removed, then remove the remaining screws.
Grasp the flywheel in both hands and pull it off the crankshaft. Joggling the
flywheel back and forth will facilitate removal.
Fig. 150
3. Removal of the rear plate.
The rear plate is held in position with a locating dowel. Remove the plate,
keeping it as square as possible to the engine block.
Fig. 151
4. Removal of the oil seal carrier.
Remove the screws that hold the oil seal carrier in position. Remove the oil
seal carrier from the engine block with a screwdriver or the like.
m Take care not to damage the oil seal.
Fig. 152
5. Removal of the tappets.
Remove the tappets from the engine block using a valve pushrod.
m If the camshaft is removed before the tappets, the tappets will fall
into the sump.
Fig. 153
30-35
Method of intervention
6. Removal of the speedometer drive gear.
Remove, in order, the locking plate and the speedometer drive gear.
m Unless the speedometer drive gear is removed, the camshaft can-
not be removed.
Fig. 154
7. Removal of the crankshaft pulley.
DANGER
When removing the crankshaft pulley, be aware that the rod
used to prevent the crankshaft from turning may suddenly
slip, so be ready to stop applying force to the crankshaft
pulley nut immediately in order to prevent possible injury.
Screw two safety studs (M12 x 1.25) into the threaded holes in the rear end
of the crankshaft. Insert a third rod between the studs to hold the crankshaft
against rotation, then remove the crankshaft pulley.
Fig. 155
8. Removal of the timing cover.
Remove the retaining screws and remove the timing cover.
m The front plate is fixed to the inside the timing cover with screws.
Do not attempt to remove this plate along with the timing cover by
tapping.
Fig. 156
30-36
Method of intervention
9. Measuring timing gear backlash.
Measure the backlash between the individual gears, making a note of the
values so they can checked on subsequent refitting. Replace the gears if
the backlash exceeds the prescribed limit.
Table 35
Fig. 158
11. Removal of the camshaft.
Remove the screws securing the thrust plate, then withdraw the camshaft
from the engine block.
m Take care not to damage the lobes or the bearing journals when
removing the camshaft.
Fig. 159
30-37
Method of intervention
12. Removal of the fuel injection pump camshaft.
Remove the stop screw.
Fig. 160
13. Tap the rear end of the camshaft gently with a copper bar in order to drive
it out from the front end of the engine block.
Fig. 161
14. Removal of the gears.
m Remove the gears only if necessary.
To remove the gears from the camshaft and fuel injection pump camshaft, use an arbor press.
15. Removal of the oil pump.
Remove the screws securing the oil pump to the engine block and remove
the pump.
Fig. 162
16. Removal of the front plate.
Remove the four screws securing the front plate. Tap the plate lightly with a
rubber mallet to separate the gasket.
Fig. 163
30-38
Method of intervention
Inspection
Fig. 165
30-39
Method of intervention
2. Refitting the oil pump.
Make sure the gasket is correctly located on the oil pump. Locate the oil
pump on the engine block. Install the three screws and tighten them evenly.
Make sure the oil pump gear rotates freely.
Fig. 166
3. Turning over the engine.
Install two screws (M12 x 1.25) in the flywheel screw holes in the crank-
shaft. Insert a bar between the screws and turn the crankshaft to bring No.
1 piston to the top dead centre, as shown in the figure.
Fig. 167
4. Refitting the fuel injection pump camshaft
Locate the camshaft (complete with bearing and gear) in the engine block.
Tap the gear with a rubber mallet to seat the bearing; check that the cam-
shaft rotates freely, then tighten the stop screw.
Fig. 168
5. Refitting the camshaft.
Lubricate the lobes and bearing journals with engine oil; Locate the cam-
shaft (complete with gear) in the engine block.
m Take care not to damage the lobes or the bearing journals when
inserting the camshaft.
Fig. 169
30-40
Method of intervention
6. Tighten the screws securing the thrust plate to the specified torque.
Table 36
Make sure the camshaft rotates freely and check the camshaft end float.
Fig. 170
7. Refitting the idler gear.
Lubricate the idler gear with engine oil. Locate the idler gear in position with
the 3, 2 and 11 marks aligned respectively with the 33 mark on the
fuel injection pump camshaft gear, the 22 mark on the camshaft gear and
the 1 mark on the crankshaft gear.
m Check the gear backlash.
Fig. 171
8. Refitting the timing cover.
Coat the gasket with adhesive and locate it on the front plate. Lubricate the
oil seal lip with engine oil. Tighten the screws securing the timing cover.
Fig. 172
9. Tightening the crankshaft pulley nut.
Fit two screws (M12 x 1.25) in the flywheel screw holes in the crankshaft
and counterhold the crankshaft. Tighten the crankshaft pulley nut to the
specified torque.
Table 37
m Ensure that the screws and bar used to counterhold the crankshaft Fig. 173
are strong enough.
30-41
Method of intervention
10. Refitting the PTO gear.
Locate the PTO gear in the timing cover, with the side without the lubrica-
tion hole facing the rear end of the engine.
Fig. 174
11. Refitting the speedometer drive gear.
Install the O-ring in the groove in the drive gear sleeve. Locate the speed-
ometer drive gear in the engine block while rotating the gear or the cam-
shaft.
Fig. 175
12. Refitting the tappets.
Lubricate the tappets with engine oil (A) and locate in the engine block.
Fig. 176
13. Refitting the oil seal carrier.
Locate a gasket on the oil seal carrier; Lubricate the oil seal lip with engine
oil and locate the oil seal in the engine block.
Fig. 177
30-42
Method of intervention
14. Refitting the rear plate.
Locate a new gasket on the rear plate. Locate the rear plate on the engine
block, aligning the holes with the locating dowels. Tighten the screws se-
curing the rear plate to the specified torque.
Table 38
m To facilitate installation of the rear plate, install the starter motor on Fig. 178
the plate before fitting the plate to the engine block.
15. Refitting the flywheel.
Insert a stud (M12 x 1.25) in the rear end of the crankshaft. Locate the
flywheel, aligning it with the stud; insert three of the four screws in the
flywheel and tighten them by hand. Remove the stud, then fit and hand-
tighten the remaining flywheel screw.
Fig. 179
16. Have an assistant hold the crankshaft pulley with a wrench to prevent the
flywheel from rotating; then tighten the four flywheel screws to the specified
torque.
Table 39
DANGER
Fig. 180
When working with other persons, use appropriate signals
to avoid possible accidents or injuries.
30-43
Method of intervention
30.1.13 - Inspection of the flywheel and ring gear
Inspection
1. Place the flywheel on the flat plate. Set a dial gauge at one side of the fric-
tion (clutch contact) face and move it over to the opposite side of the face
as shown in the figure to find the flatness error.
m If the flatness error exceeds the limit, grind the face.
Table 40
Fig. 181
2. Examine the ring gear.
m Renew the ring gear it if its teeth are abnormally worn or chipped,
Heat the ring gear evenly with an oxyacetylene torch. Tap the ring gear all
the way around with a rod and a hammer, as shown in the figure, to remove
it from the flywheel.
Heat the new ring gear up to a temperature of 150C (302F) using a piston
heater and install it to the flywheel with its unchamfered side foremost.
Fig. 182
30-44
Method of intervention
30.1.14 - Inspection of the pistons, piston rings and gudgeon pins
Inspection
1. Using a micrometer, measure the diameter of the piston at its skirt in a di-
rection perpendicular to the gudgeon pin (1), as shown in the figure.
m If the diameter exceeds the specified limit, renew the piston.
Select a new piston so that the difference between average weight of all
pistons in one engine does not exceed the standard.
Table 41
30-45
Method of intervention
3. Put the piston ring in a gauge or in the bore in a new engine block and mea-
sure the gap between the ends of the ring with a feeler gauge as shown in
the figure.
m If the end gap exceeds the limit, renew all the rings.
Inside diameter of gauge.
Standards:
78 (from 0 to 0.03) mm; 3.07 (from 0 to 0.0012) in
0.25 (from 0 to 0.03) mm; 0.0098 (from 0 to 0.0012) in
oversize: 78.25 (from 0 to 0.03) mm; 3.08 (from 0 to 0.0012) in
0.50 (from 0 to 0.03) mm; 0.0197 (from 0 to 0.0012) in
oversize: 78.50 (from 0 to 0.03) mm; 3.09 (from 0 to 0.0012) in Fig. 185
m Put the piston ring in the gauge or cylinder square with the piston.
Table 43
30-46
Method of intervention
30.1.15 - Inspection of the connecting rods
Inspection
1. Check the connecting rod for bending or twisting.
Measure dimension (C) and dimension (L).
m If (C) exceeds 0.05 mm (0.0020 in.) per 100 mm (3.94 in.) of L
straighten the connecting rod with a press.
1.1. Gudgeon pin
1.1. Bend
1.1. Twist
m Units: mm (in)
Table 45 Fig. 187
Fig. 188
30-47
Method of intervention
4. To check the straightness of the connecting rod fitted to the piston, put the
connecting rod and piston on the surface plate as shown in the figure, insert
a round bar of diameter equal to that of the crankpin into the big end bore
and measure (A) and (B) with a dial gauge. Subtract (A) from (B) to obtain
curvature (C).
Fig. 189
Item Standard
Clearance between camshaft jour- 0.15 mm (0.0059 in)
nal and bearing
Fig. 190
2. Measuring the bore of the camshaft bearing]
m To renew the camshaft bearings, use the special bearing installation
tool.
Fig. 191
3. Remove the sump. Using the remover end of the tool, force the bearing
out of the engine block. Crush and remove the bearing from the block.
3.1. Front end of engine block
3.2. Camshaft bearing
3.3. Bearing installer
Fig. 192
30-48
Method of intervention
4. Install a new bearing, aligning the oil holes with those of the oil gallery.
4.1. Oil holes
4.2. Notch in bearing
4.3. End of bearing
Fig. 193
5. Measure the cam lobe height and base circle as shown in the figure. Sub-
tract the base circle from the lobe height to find the cam lift. If the cam lift
exceeds the specified limit, renew the camshaft.
Table 48
Fig. 194
Fig. 195
2. Measure the diameter of the tappet and of the corresponding bore in the
engine block to find the clearance.
m If the clearance exceeds the specified limit, replace the tappet.
Table 49
Item Standard
Clearance between tappet and en- 0.15 mm (0.0059 in)
gine block
Fig. 196
30-49
Method of intervention
30.1.18 - Inspection of the idler gear
Inspection
1. Measure the bore in the idler gear for the shaft and the diameter of the shaft
to find the clearance.
m If the clearance exceeds the specified limit, replace either the gear
or the shaft, whichever is most worn.
Table 50
Fig. 198
30-50
Method of intervention
2. Valve guides wear more rapidly at their ends than at any other part.
Using a bore gauge (A), measure the inside diameter of the valve guides at
both ends to find the clearance between valve stem and valve guide,
m If the clearance exceeds the specified limit, renew the valve guide or
valve, whichever is most worn.
Table 52
Fig. 201
4. Insert a new valve (3) in the guide (1); make sure the valve slides in the
guide freely.
After renewing the valve guide (1), check the contact between the valve (3)
and its seat (4)
Put a small amount of Prussian blue or read lead on the valve face (5).
Hold valve (3) with a valve lapping tool (6) and press it against seat (4) to
check the contact.
Fig. 202
30-51
Method of intervention
5. The width of contact (7) must be uniform all the way around both the seat
and the valve (C).
m If the contact is incorrect (D), reface the valve and seat.
Fig. 203
6. m If the valve margin (8) exceeds the specified limit, renew the valve
(3).
m If the valve sinkage (9) exceeds the specified limit, recondition the
valve seat or renew the cylinder head assembly
Table 53
Fig. 205
8. Check the clearance between the valve (3) and valve guide (1) before
refacing the valve seat (4).
m Renew the valve guide (1) if necessary.
Finish the valve seat (4) using a finishing tool or a valve seat grinder (E).
Fig. 206
30-52
Method of intervention
9. Check the valve face angle (F) and valve seat width (G).
Table 55
Fig. 207
10. Be sure to lap the valves (3) in their seats after refacing or renewal of the
valves or valve seats (4).
Put a small amount of lapping compound on the valve face.
m Do not put lapping compound on the valve stem.
m Use a 120 - 150 grit lapping compound (H) for initial lapping and a
compound finer than 200 grit for finish lapping.
m Mixing the compound with a small amount of engine oil will help
distribute the compound on the valve face uniformly.
Using a lapping tool, hold the valve (3) in its seat (4) and rotate it only a part
of a turn, then raise the valve off its sealing surface to reposition it. Press Fig. 208
the valve against the sealing surface and rotate through another part turn.
Repeat this operation until the compound wears and loses its cutting prop-
erty.
Wash the valve (3) and valve seat (4) with dry cleaning solvent.
Apply engine oil to the valve (3) and lap it in the seat (4).
Check the valve face contact (7).
A - Front of engine
Fig. 209
30-53
Method of intervention
2. Find TDC on the compression stroke for No. 1 piston using the following
procedure:
- rotate the crankshaft to bring the TDC mark on the crankshaft pulley into
alignment with the mark on the timing cover;
- with No. 1 piston at TDC on the compression stroke, the rocker arms
should not move when the crankshaft is turned approximately 20 in both
directions;
- if the rocker arms move, No. 1 piston is at top dead center on the intake
or exhaust stroke; in this case, rotate the crankshaft through 360 in the
normal direction of engine rotation. No. 1 piston is now at top dead centre
on the compression stroke.
Fig. 210
Loosen the lock nut of the adjusting screw. With a feeler gauge inserted
between the rocker arm and valve cap, adjust the valve clearance by turn-
ing the adjusting screw.
Table 57
Item Standard
Valve clearances (intake and ex- 0.25 mm (0.0098 in)
haust valves)
A - TDC (top dead center) mark for pistons No. 1 and No. 4
B - Mark on timing cover.
C - Injection timing mark.
D - TDC mark for pistons No. 2 and No. 3.
3. Hold the adjusting screw and tighten the lock nut. After adjusting the valve
clearance on the valves for No. 1 cylinder, rotate crankshaft 180 in the
direction of engine rotation and adjust the valve clearance on the valves for
the remainder of the cylinders in firing order (injection sequence).
Table 58
30-54
Method of intervention
30.1.21 - Inspection of the rocker arms and rocker shaft
Inspection
1. Measure the inside diameter of the bore in the rocker arm for the rocker
shaft and the diameter of the rocker shaft to find the clearance between
the arm and shaft.
m If the clearance is on the limit, renew the rocker arm.
m If it exceeds the limit, renew both the rocker arm and the shaft.
Table 59
30-55
Method of intervention
Fig. 214
30-56
Method of intervention
2. Disassembly of the rocker shaft assembly.
Mark each rocker arm with its relative location on the rocker shaft.
Fig. 215
3. Removal of the cylinder head screws.
Loosen the cylinder head screws gradually in stages in the sequence
shown.
m If any parts of the cylinder head are faulty, check the tightness of the
cylinder head screws with a torque wrench before loosening them.
Fig. 216
4. Removal of the cylinder head assembly.
Using a hoist, lift the cylinder head straight up and off the engine.
m If the gasket is stuck fast and the cylinder head cannot be separated
from the cylinder block, tap around the side of the cylinder head with
a rubber mallet
Fig. 217
5. Removal of the valves and valve springs.
Compress the valve spring with a valve lifter and remove the collet, the
spring retainer, the spring and the valve.
m The valves, spring retainers, springs and collets must be set aside
separately in groups, each labelled with the cylinder number, to en-
sure subsequent installation in the original position.
Fig. 218
30-57
Method of intervention
6. Removal of the valve stem seals.
Remove the valve stem seals.
m Do not reuse the valve stem seals.
Fig. 219
Inspection
30-58
Method of intervention
Refitting
1. Cleaning the lower face of the cylinder head.
Scrape the old gasket from the lower face of the cylinder head.
m After scraping off the gasket, remove all residue using an oilstone
smeared with engine oil and thoroughly clean the face.
Fig. 221
2. Installing the valve stem seal.
Using a box wrench, locate the valve stem seal in the valve guide. After
installation, make sure the seal is in its correct position.
m Incorrect installation of the seal can cause a failure to seal against
the downward flow of oil along the stem.
Fig. 222
3. Refitting the valve spring.
Install the valve spring with the white enamelled end (A) uppermost.
Fig. 223
4. Refitting the valve assembly.
Compress the valve spring with a valve lifter and install the assembly on
the valve tip.
m Do not compress the valve spring excessively, otherwise the valve
spring retainer could impact and damage the valve stem seal.
Fig. 224
30-59
Method of intervention
5. Refitting the cylinder head gasket.
Thoroughly clean the top face of the engine block and the pistons, then
insert the two guide screws (A) in the relative holes in the engine block.
m Guide screws: M10 x 1.25
Locate a new cylinder head gasket on the engine block, making sure the
guide screws are all aligned with their respective holes in the gasket (A).
m Do not use any gasket adhesive or other substances on the top face
of the engine block.
Fig. 225
6. Refitting the cylinder head.
Locate the cylinder head on the engine block, making sure the guide
screws are all aligned with the corresponding holes in the cylinder head (A).
Fig. 226
7. Tightening the cylinder head screws.
Remove the guide screws and fit the screws that secure the cylinder head
to the engine block, then gradually tighten the screws in a number of stages
and in numeric order to the specified torque.
Table 60
Fig. 227
8. Refitting the pushrods.
Insert the pushrod in the relative bore in cylinder head, making sure that
the spherical end of the pushrod correctly engages the recess in the tappet.
Fig. 228
30-60
Method of intervention
9. Refitting the rocker shaft assembly.
Install the rocker arms, pedestals and springs on the rocker shaft. Tighten
screws (A) to secure the rocker pedestals to the shaft.
m Check that the rocker arms move freely,
Fig. 229
10. Refitting the rocker shaft assembly.
Locate the valve caps on the tips of the valve stems, then locate the rocker
shaft assembly on the cylinder head. Finally, tighten the rocker shaft as-
sembly retaining screws to the specified torque.
Table 61
Fig. 230
11. Adjusting the valve clearances.
Adjust the valve clearances to the specified values.
Fig. 231
12. Refitting the rocker cover.
Make sure the gasket is fitted to the rocker cover, then tighten the rocker
cover screws to the specified torque.
Table 62
Fig. 232
30-61
Method of intervention
30.1.23 - Inspection of the cylinder head
Checking the gasket face of the cylinder head for warpage
1. Using an accurate straight edge and a feeler gauge, check the gasket face
for warpage in three positions lengthwise, two crosswise and two widthwise
as shown in the figure.
m In the case of warpage in excess of the specified limit, regrind the
gasket face of the cylinder head using a grinder for flat surfaces.
Table 63
Item Limit
Bend (dial gauge reading) of push- 0.3 mm (0.012 in) maximum
rod
Fig. 235
30-62
Method of intervention
Renewal
1. m Renew the jets only if cracked or defective.
To unseat jet (1), insert a 6 mm (0.24 in.) diameter rod (2) through the glow-
plug bore in the cylinder head.
Fig. 236
2. To install new jet (3), locate it in the cylinder head with its tangential orifice
aligned with the centre of the main chamber and tap it gently with a rubber
mallet.
Fig. 237
Fig. 238
2. Removal of the pressure relief valve.
Remove the pressure relief valve from the engine block.
Fig. 239
30-63
Method of intervention
3. Removal of the oil pressure switch.
Remove the oil pressure switch with the specific box wrench.
Fig. 240
Refitting
1. Refitting the pressure relief valve.
Locate the relief valve in the engine block and tighten it to the specified
torque.
Table 66
Fig. 241
2. Refitting the oil filter.
Lightly oil the seal with engine oil and screw on the new filter by hand until
the seal is in contact with the base, then tighten to the specified torque.
Fig. 242
3. Refitting the oil pressure switch.
Apply threadlocker to the thread (A) of the oil pressure switch, then install
the pressure switch using the specific wrench.
m Apply threadlocker to the threads only.
m Do not over-tighten the oil pressure switch.
Fig. 243
30-64
Method of intervention
30.1.28 - Inspection of the lubrication system
Inspection
1. Oil pump.
Visually check the pump for rough rotation or other defects.
m Replace the pump assembly if defective.
Fig. 244
2. Oil pressure switch.
Test for electrical continuity between the terminal and body using an ohm-
meter, as shown in the figure.
m If there is no electrical continuity, the switch must be renewed.
Fig. 245
3. Insert a small diameter rod into the oil hole in the switch and lightly push it
in to test for electrical continuity, as shown in the figure.
m If there is no electrical continuity, renew the pressure switch.
Apply air pressure of 0.5 kgf/cm (7 psi) [49 kPa] to the switch through the
oil hole and test for continuity.
mIf there is no electrical continuity, renew the pressure switch.
Check for air leaks.
m The presence of air leaks indicates that the membrane is broken, in
which case the pressure switch must be renewed.
Fig. 246
4. Pressure relief valve.
Check the valve seat contact. Check the spring for damage. Measure the
oil pressure at which the relief valve opens (the oil pressure with engine
running at the rated rpm). The engine oil pressure test outlet is located on
the right side of engine.
m If the pressure is not correct, remove the cap nut and either increase
or reduce the shim thickness accordingly.
Table 67
Relief valve opening pressure 3.5 0.5 kgf/cm (50 7 psi) [343+
Fig. 247
49 kPa]
1 - Cap nut.
2 - Shims.
30-65
Method of intervention
30.1.29 - Fuel System
Disassembly
1. Removal of the fuel injection pipes.
Disconnect the fuel injection pipes and fuel leak-off pipe from the fuel injec-
tion pump and nozzles.
m Put plugs or caps on the openings of the injection pump and nozzle
connectors.
Fig. 248
2. Removal of the fuel injection nozzles.
Loosen the fuel injection nozzles with a wrench. Remove the nozzles and
seals from the cylinder head.
m Remove the seals from the cylinder head with a screwdriver or simi-
lar tool. Discard any defective seals.
Fig. 249
3. Removal of the governor assembly.
Remove the control rod cover; remove the control spring using pliers, and
disconnect the control rod from the injection pump, then remove the gov-
ernor assembly.
Fig. 250
4. Removal of the governor flyweights.
Remove the sliding sleeve, the sliding sleeve shaft and remove the gover-
nor flyweights.
Fig. 251
30-66
Method of intervention
5. Removal of the fuel injection pump.
Remove the control rod cover and remove the control rod spring using pli-
ers; disconnect the control rod from the injection pump.
Fig. 252
6. Remove the injection pump.
m Make a note of the thickness of the shims for subsequent installa-
tion.
Fig. 253
Refitting
1. Refitting the fuel injection nozzles.
Fit the seal to the nozzle (A). Locate the nozzle assembly in the cylinder
head and tighten it to the specified torque.
Table 68
Fig. 254
2. Refitting the fuel injection pump
Locate the pump on the engine block and tighten the screws securing the
pump to the specified torque.
Fig. 255
30-67
Method of intervention
3. Refitting the flyweight assembly.
Locate the flyweight assembly on the rear end of the fuel injection pump
camshaft and tighten the sliding sleeve shaft to the specified torque.
Table 69
Fig. 256
4. Refitting the sliding sleeve.
Install the sliding sleeve on the sliding sleeve shaft and make sure the
sIeeve moves freely.
Fig. 257
5. Refitting the governor assembly.
Locate the governor assembly while simultaneously installing the control
rod and spring in the injection pump; attach the control rod to the pin of the
control rack and secure it with the spring, then locate the control rod cover.
Fig. 258
6. Refitting the fuel injection system pipes.
Locate the fuel leak-off line and connect it to the fuel injection nozzles; then
locate the fuel injection pipes and connect them to the fuel injection pump.
Install the clamps.
Fig. 259
30-68
Method of intervention
30.1.30 - Inspection and adjustment of the fuel system
Maintenance
Preparation
1. Close the fuel filter valve. Disconnect the fuel injection pipe from the cylin-
der head and from the injection pump. Remove the delivery valve holder
from the injection pump. Remove the delivery valve and spring from the
holder. Refit the delivery valve holder to the injection pump only. Connect
the pipe to the injection pump. Hold the speed control lever in the low revs
position.
Fig. 260
Inspection
1. Fuel system.
Open the fuel filter valve. Turn the starter switch key to ON position.
m Fuel will flow from the injection pipe at high pressure when the start-
er switch key is turned to the ON position if the engine is equipped
with an electric lift pump. Direct the fuel flow into a container.
Fig. 261
2. Slowly turn the crankshaft clockwise, while watching the free end of the
injection pipe. The instant the fuel stops flowing represents the fuel injec-
tion timing.
m Rotate the crankshaft in reverse direction just a little and repeat the
operation described above again to recheck the injection timing.
Fig. 262
3. The fuel injection timing is correct if the timing mark on the crankshaft pulley
is aligned with the mark on the timing cover when fuel stops flowing from
the injection pipe.
Table 70
A - TDC (top dead center) mark for pistons No. 1 and No. 4
B - Timing mark on timing cover.
C - IT (injection timing) mark.
D - TDC mark for pistons No. 2 and No. 3.
Fig. 263
30-69
Method of intervention
4. Alternative method.
In the fuel flow method, the delivery valve has to be removed. As a result,
there is a good chance for dirt particles to get inside the fuel injection pump.
In this alternate method, however, it is not necessary to remove the delivery
valve.
Disconnect No. 1 fuel injection pipe at the fuel injection nozzle (cylinder
head). Prime the fuel lift pump. Slowly turn the crankshaft clockwise until
the point where fuel flows freely from the open end of the injection pipe and
then check the position of the timing mark relative to the mark on the timing
cover. The timing is retarded by approximately 1. Take this retard angle of
1 into account when adjusting the shims.
Fig. 264
Adjustment
1. If the fuel injection timing is incorrect, alter the thickness of shims under the
fuel injection pump. An increase or decrease in shim thickness of 0.1 mm
(0.004 in.) will result in a 1 change in the timing. Increase the thickness of
the shims to retard the timing or decrease it to advance the timing.
Table 71
Fig. 266
30-70
Method of intervention
30.1.31 - Inspection of the fuel lift pump
Inspection
1. Examine the exterior of the pump for defects and test its performance.
mDo not attempt to disassemble the pump.
Plunger-type fuel lift pump.
Fig. 267
2. Diaphragm-type fuel lift pump.
Fig. 268
Table 72
30-71
Method of intervention
Disassembly
30-72
Method of intervention
10. Control rack
11. Delivery valve holder
12. O-ring
13. Delivery valve spring
14. Delivery valve gasket
15. Delivery valve
16. Plunger barrel
17. Pump housing
Removal of the tappets
1. Hold the injection pump in a vice with the tappet side (3) facing upwards.
Using a screwdriver, separate the lock plate from the tappet guide pin.
Rotate the tappet guide pin 180 to release it.
Fig. 270
2. Remove tappet guide pin (1) with long-nose pliers while pushing down on
tappet (3), then remove the tappet.
Repeat the above procedure to remove all the remaining tappets.
m The tappet may be expelled from its bore when the tappet guide pin
is removed. Hold the tappet to prevent it from falling Hold the tappet
to prevent it from falling.
Fig. 271
Fig. 272
30-73
Method of intervention
Removal of the delivery valves
1. Turn the injection pump upside down and hold it in a vice.
Remove delivery valve holder (11), then remove the spring and the gasket.
Fig. 273
2. Remove the delivery valve (15) with pliers.
Repeat the above procedure to remove all the remaining delivery valves.
m The delivery valves are delicate components. Keep them as clean
as possible.
Fig. 274
Fig. 275
2. m When renewing the plungers and barrels or delivery valves, do not
loosen the adjusting plates (A) between the pumping elements.
m After renewing components, the injection pump delivery must be
measured. Use the specific tester to measure the injection pump
delivery.
m Keep disassembled injection pump parts in clean diesel fuel.
Fig. 276
30-74
Method of intervention
Inspection
30-75
Method of intervention
Assembly
To assemble, follow the disassembly steps in reverse order.
Use the following procedure:
30-76
Method of intervention
Refitting the barrels
1. Locate each barrel (16), aligning the groove with locating dowel (A) and
inserting it squarely into its bore.
m If the groove in the barrel is not aligned with the locating dowel, the
O -ring will not seat correctly (it will still be visible) after the delivery
valve holder has been installed.
Fig. 279
Fig. 280
Fig. 281
2. Locate plungers (6) in their respective barrels.
m Make sure the notch in the plunger is pointing toward the adjustment
plate.
Fig. 282
30-77
Method of intervention
Refitting the tappets
1. Move the control rack back and forth while pushing down on each tappet
(3) to align the slot in the tappet with the hole in the housing for the tappet
guide pin. Locate lock plates (2) and tappet guide pins (1).
m Every time the fuel injection pump is disassembled, new lock plates
must installed.
Fig. 283
Fig. 284
Post-assembly inspection
1. Immediately after reassembling the fuel injection pump, check that the con-
trol rack moves freely without any binding or catching.
If the control rack fails to move freely, the possible causes are Pumping
element(s) sticking; Foreign particles lodged between control rack and
sleeves; Over-tightening of delivery valve holder(s).
Disassemble and check the injection pump to locate the cause of the prob-
lem.
After reassembly of the fuel injection pump, check the injection timing.
Fig. 285
Fig. 285
30-78
Method of intervention
30.1.34 - Inspection of the fuel injection pump camshaft
Test
1. Measure the lobe height and base circle as shown in the figure. Subtract
the base circle from the lobe height to find the cam lift. If the cam lift ex-
ceeds the prescribed limit, renew the camshaft.
Table 74
Fig. 285
30-79
Method of intervention
30.1.35 - Fuel injection nozzle
Disassembly
30-80
Method of intervention
Inspection
1. DANGER
Wear safety goggles when testing the nozzles. Fuel spray-
ing out from the nozzles under high pressure can perforate
the skin and cause serious lesions. Never direct the nozzle
towards yourself or other persons, always point it in the di-
rection of the collector.
Injection pressure (valve opening pressure) test.
Install the injection nozzle on the tester. Operate the tester handle slowly at
a speed of one stroke per second to make gradually increase the pressure
to the point where the valve in the injection nozzle starts to open.
Read the maximum pressure reading at the instant fluid flows from the tip. Fig. 287
2. If the injection pressure is incorrect, disassemble the nozzle and change
the thickness of washer (6).
m Injection pressure (valve opening pressure) Standard : 140 kgf/cm
(1991 psi) [13729 kPa].
m An increase or decrease in the washer thickness of 0.1 mm (0.004
in.) will result in a change in the injection pressure of 10 kgf/cm (142
psi) [981 kPa]. 10 washers are available in thicknesses from 1.25
mm (0.0492 in.) to 1.70 mm (0.0669 in.) in increments of 0.05 mm
(0.0020 in).
Fig. 288
3. Nozzle hole restriction test.
Observe the pattern of the spray as it leaves the nozzle: the fuel spray
should be straight (A). Any variation in the spray pattern is an indication of
a fault in the nozzle (B).
Operate the tester handle at a speed of one stroke per second to check that
the spray profile is straight.
Fig. 289
30-81
Method of intervention
4. Washing and renewing the nozzles.
Loosen lock nut (1), and remove tip (2) from the injection nozzle; wash
needle valve (C) and body (D) in clean diesel fuel. After washing, replace
the needle valve in the body with clean diesel fuel.
m When removing the tip from the injection nozzle, be careful not to
damage it.
m Keep the needle valves together with their respective bodies. Do not
use needle valves with bodies of a different type.
After cleaning tip (2), install it in the nozzle and tighten lock nut (1) to the
specified torque.
Fig. 290
m Tightening torque: 3.75 0.25 kgf x m (27 1.8 Ibf x ft) [36.8 2.5
N x m].
If the injection nozzle is still faulty after the tip has been washed, renew tip
(2).
m Do not touch the sliding surface of the needle valve.
m When installing the new nozzle tip, remove the synthetic resin film
from the tip and slide the needle valve in the body with clean diesel
fuel to wash off all traces of the protective film.
Assembly
1. To assemble, follow the disassembly steps in reverse order.
Fig. 291
30-82
Method of intervention
30.1.37 - Governor
Disassembly
30-83
Method of intervention
Assembly
1. Locate levers (3), (7), (9) and (11).
Install the O-ring on governor shaft (6).
Locate shaft (6) in governor housing (12), and install levers (3), (7), (9) and
(11) on the shaft.
Fig. 293
2. Install grooved pin (5) and spring pin (4) using a hammer.
Locate tie-rod (2) and spring (1).
Fig. 294
3. Remove the tie-rod cover
Move speed control lever (3) to the high idle position and hold it there.
Move tie-rod (2) in the direction of the arrow to the point where a slight
resistance is encountered.
m In this position, tie-rod (2) does exert force on governor spring (10).
m Torque spring assembly (A) is to be installed and adjusted after hav-
ing first adjusted the low idle speed and high idle speed, with the
engine not running.
Fig. 295
4. Rotate torque spring assembly (A), while slightly moving tie-rod (2) until the
reference mark on control rack (B) is aligned with the mark on the pump
body (C).
With these reference marks aligned, secure torque spring assembly (A) in
position by tightening nut (D).
Install sealing cap (E) over the torque spring assembly (A) and stake the
cap in position.
Fig. 296
30-84
Method of intervention
30.1.38 - Cooling system
Disassembly
1. Removal of the cooling fan.
While holding the fan with one hand, remove the four fan retaining screws
and then remove the fan and the spacers.
m Keep the spacers with the fan for subsequent refitting.
Fig. 297
2. Removal of the thermostat housing.
Remove the assembly containing thermostat.
Fig. 298
3. Removal of the water pump assembly.
Remove the water pump assembly.
Fig. 299
Refitting
1. Refitting the water pump.
Locate the water pump on the engine block.
m Renew the water pump flange gasket on reassembly.
Fig. 300
30-85
Method of intervention
2. Refitting the thermostat.
Locate the thermostat in the thermostat housing, then locate the thermostat
assembly on the cylinder head.
m Renew the thermostat housing gasket on reassembly.
Fig. 301
3. Refitting the cooling fan.
Locate the spacers in the fan as shown in the figure; locate the pulley on
the water pump, then locate the fan/spacer assembly on the pulley.
Fig. 302
4. Refitting the thermoswitch connected to the preheating control unit.
Apply Three Bond 1104 to the threads of the thermoswitch and thermostat
unit (A). Locate the thermoswitch and thermostat unit and tighten it to the
specified torque.
Table 76
Fig. 303
30-86
Method of intervention
30.1.39 - Inspection of the cooling system
Inspection points
Fig. 305
30-87
Method of intervention
2. Standard thermostat.
DANGER
Contact with the water in the radiator can cause severe
burns.
Hang the thermostat in a pan of water as shown in the figure. The thermo-
stat must be below the surface of the water and it must not touch the sides
of the pan. Heat the water uniformly in the pan and read the temperature at
which the thermostat valve starts opening and the temperature at which the
valve lift (distance) is 8 mm (0.3 in).
Table 77 Fig. 306
Hang the thermoswitch in a pan of oil with its temperature sensor below the
surface of oil and measure the resistance while heating the oil as shown
in the figure.
Table 78
Hang the preheating control unit in the pan of antifreeze with its tempera-
ture sensing end below the surface of antifreeze and measure the resis-
tance while gradually heating the antifreeze as shown in the figure.
Table 79
30-88
Method of intervention
30.1.40 - Engine air intake pipe
Removal
1. Disconnect filter clogging sensor (1).
Fig. 309
2. Remove retaining clamp (2).
Fig. 310
3. Disconnect the air intake pipe from turbocharger (3).
Fig. 311
4. Remove intake pipe (4).
Fig. 312
30-89
Method of intervention
Refitting
1. Refitting is the reverse of removal.
Fig. 313
2. Removal of the air intake manifold.
Remove the air intake manifold from the cylinder head.
Fig. 314
Refitting
1. Refitting the air intake manifold.
Tighten the screws securing the air intake manifold (1) to the specified
torque.
m Use a new gasket (2).
Table 80
Fig. 315
2. Refitting the exhaust manifold.
Tighten the screws securing exhaust manifold (1) to the specified torque.
m Use a new gasket (2).
Table 81
Fig. 316
30-90
Method of intervention
30.1.42 - Inspection of the air intake and exhaust system
Inspection
30-91
Method of intervention
Item Standards
Warpage of manifold 0.15 mm (0.0059 in)
Fig. 319
30-92
Method of intervention
30.2 - C0 - Engine accessories
30.2.1 - Engine cooling system radiator
Removal
1. Open radiator cap (1) to allow the coolant to flow and then open drain valve
(2).
Fig. 320
2. Remove the clamp securing coolant recovery hose (3).
Fig. 321
3. Remove the four upper screws and two lateral screws (4) and remove RH
fan guard (5).
Fig. 322
4. Remove the three retaining screws (6) and remove LH fan guard (7).
Fig. 323
30-93
Method of intervention
5. Remove the three retaining screws (8) of the top hose shroud.
Fig. 324
6. Loosen clamp (9) to disconnect top hose (10).
Fig. 325
7. Remove screw (11) securing the radiator to the engine mounting.
Fig. 326
8. Remove the six hex socket screws (12) securing the fan cowling.
Fig. 327
30-94
Method of intervention
9. Remove the two lower radiator retaining screws (13) on either side.
m Recover the silent blocks for subsequent refitting.
Fig. 328
10. Tilt the radiator forwards and loosen clamp (14) to disconnect the bottom
hose.
Fig. 329
11. Tilt the radiator forwards and loosen clamp (15) to disconnect the water
drain hose.
Fig. 330
12. Remove radiator (16).
Fig. 331
30-95
Method of intervention
Refitting
1. Refitting is the reverse of removal.
m On refitting, make sure that the silent blocks are installed in the correct positions.
Fig. 332
2. Remove RH fixing screw (2) and clamp (3).
Fig. 333
3. Remove expansion tank (4).
Fig. 334
Refitting
1. Refitting is the reverse of removal.
30-96
Method of intervention
30.2.3 - Fan
Removal
1. Remove the three fixing screws (1).
Fig. 335
2. Remove the centre nut (2) of the fan by turning it clockwise (LH thread),
while holding the back of the fan against rotation.
m Use a pneumatic hammer nut runner.
m Apply pressure in brief spurts to avoid damaging the nut.
Fig. 336
3. Remove fan (3).
Fig. 337
Refitting
1. Refitting is the reverse of removal.
m Centre nut: Loctite 510.
30-97
Method of intervention
30.2.4 - Air cleaner assembly
Removal
1. Loosen retaining clamp (1).
Fig. 338
2. Remove upper collar (2).
Fig. 339
3. Remove air cleaner assembly (3).
Fig. 340
30-98
Method of intervention
Refitting
Refitting is the reverse of removal.
30.2.5 - Fuel filter
Disassembly
1. Normally, the fuel filter is not to be disassembled. It is recommended that
only the element is removed for cleaning or renewal.
When installing the valve lever after washing, coat the lever O-ring with
silicone oil and the washer with grease.
1 - Nut
2 - Bowl
3 - O-ring
4 - Element
5 - Lever plate
6 - Washer
7 - Valve lever
Fig. 341
8 - O-ring
9 - Seal
10 - Valve seat
11 - Filter head
A - Do not remove
B - Coat with silicone oil
C - Coat with grease
D - Wash in diesel fuel every 100 hours of service
Replace every 500 hours of service
E - Check for water and sediment.
Fig. 342
2. Remove the upper panel by moving shroud (4).
Fig. 343
30-99
Method of intervention
3. Disconnect float switch wiring connector (5).
Fig. 344
4. Remove the float switch and recover O-ring (6).
Fig. 345
Refitting
Refitting is the reverse of removal.
Fuel tank
Removal
1. Remove steering wheel adjuster knob (7).
m Recover the copper pellet.
Fig. 346
2. Remove upper panel (4) and fuel tank filler cap (3), if the fuel tank float
switch has not already been removed.
Fig. 347
30-100
Method of intervention
3. Remove relay (8) and preheating control unit (9) from the fuel tank.
Fig. 348
4. Loosen clip (10) and remove preheating control unit wiring (11).
Fig. 349
5. Disconnect direction indicator relay (12).
Fig. 350
6. Remove retaining screws (14) and remove side panel (13) on either side.
Fig. 351
30-101
Method of intervention
7. Remove the lateral fuel tank retaining screws (15) on both sides.
Fig. 352
8. Disconnect fuel recovery pipe (16).
Fig. 353
9. Remove the three screws (18) and remove upper heat shield (17).
Fig. 354
10. Raise fuel tank (19).
m Note the position of the pipe connecting the main fuel tank to auxil-
iary tank (20).
Fig. 355
30-102
Method of intervention
11. Remove the main fuel tank.
m Take care not to lose the spacers and the damper located on the two
guides (21) of the fuel tank subframe.
Fig. 356
Refitting
Refitting is the reverse of removal.
30.2.7 - Auxiliary fuel tank
Removal
1. First drain the main fuel tank and then the auxiliary tank.
m Do not remove the drain plug of the auxiliary tank without having first removed the drain plug of the main tank.
Fig. 357
3. Disconnect fuel gauge wiring connector (2).
Fig. 358
4. Remove the auxiliary electrical connector support bracket (3) from the tank.
Fig. 359
30-103
Method of intervention
5. Remove connection pipe (4) to the main fuel tank.
Fig. 360
6. Loosen clamp (5) and disconnect fuel pickup pipe (6).
Fig. 361
7. Remove the auxiliary fuel tank.
Refitting
1. Refitting is the reverse of removal.
Fig. 362
30-104
Method of intervention
Glow plug timer specifications
1. The following table contains the standard technical data for the glow plug timer.
Table 84
Model QGS
Type Quick heating
Voltage rating 12 Vdc
Operating voltage range 7 to 15 V
Operating temperature range from -30 C to +70 C (from -22 F to +158 F)
Storage temperature range from -40 C to +80 C (from -40 F to +176 F)
Glow plug activation time 6.2 0.7 seconds
Glow plug relay specifications
1. The following table contains the standard technical data for the glow plug
relay.
Table 85
Model G71SP
Voltage rating 12 Vdc
Continuous rating 1 minute
Coil resistance 13 Ohm
Inductance 24 mH (at 1 kHz)
Operating temperature range from -40 C to +100 C (From -40 F
to +212 F)
Fig. 363
Item Standard
Resistor 0.55 Ohm
Fig. 364
30-105
Method of intervention
30.2.9 - Exhaust pipe - tractor with cab
Removal
1. Disconnect the exhaust pipe from silencer (1).
Fig. 365
2. Remove hex socket screw (2).
Fig. 366
3. Remove exhaust pipe (3).
Fig. 367
30-106
Method of intervention
Refitting
1. Refitting is the reverse of removal.
Fig. 368
30-107
Method of intervention
Refitting the engine stop solenoid
1. Remove the control rod cover. Apply thread sealant (Three Bond 1212) to
the threads of the engine stop solenoid.
m Apply sealant to the entire length of thread to be screwed into the
governor housing.
Temporarily install the engine stop solenoid and the relative nut in the gov-
ernor housing; then move the injection pump control rack to the injection
shutoff position
Insert the engine stop solenoid in the governor housing while pushing the
plunger towards the control rack to bring the shaft in contact with the control
rod. At this point, clearance C should be 0 mm. (the plunger will be rotated
as a result of the engine stop solenoid being screwed in). Fig. 370
Back off the engine stop solenoid by 30 - 45 (the clearance between the
control rack and plunger will be 0.15 to 0.20 mm (0.6059 to 0.0079 in.), then
tighten the nut to the specified torque. Start the engine and make sure the
engine stops when the plunger reaches the end of its stroke.
1 - Tightening torque: 4.5 0.5 kgf x m(32.5 3.6 lbf x ft) [44 N x m].
2 - Threads to be coated with thread sealant.
3 - Shaft.
4 - Plunger.
5 - From 0.15 mm to 0.20 mm (from 0.0059 to 0.0079 in).
m Do not allow thread sealant to contact (A) and do not allow cleaning
solvent to enter the solenoid through aperture (B).
2. Install the rubber cap in position with the arrow pointing upwards (with the
side with the water drain hole down) as shown in the figure.
m Do not allow cleaning solvent to come into contact with any part of
the solenoid.
1 - Rubber cap.
2 - Water drain hole.
Fig. 371
30-108
Method of intervention
Inspection after installation.
1. Start the engine and make sure the engine stops when the starter switch key is turned to OFF position. Start the engine and
make sure the engine stops when the oil pressure switch terminal is shorted to the switch body.
30.2.11 - Alternator
Inspection, precautions and checks
1. Inspection before removal.
The correct diagnosis of the charging system requires a careful inspection
with the alternator on the engine to determine whether or not it is necessary
to remove the alternator from the engine for further inspection.
The following chart, in which two troubles are listed with four possible
causes of each, will help locate the cause of the trouble.
Table 88
30-109
Method of intervention
3. Checking the voltage setting.
Connect the alternator to a 12 volt battery with an ammeter, a voltmeter and
a switch, as shown in the figure.
The voltmeter reading should be zero (0) when the starter switch is in OFF
position, and below the battery voltage level when the switch is in the ON
position. In this condition the engine does not start.
With one ammeter lead short-circuited, start the engine.
Check the voltmeter reading when the ammeter reading is below five am-
peres and the engine is running at 1800 rpm or 2500 rpm with no electrical
loads. The voltage setting varies with alternator temperature. Generally, the
higher the alternator temperature, the lower the voltage setting.
Fig. 374
Table 89
Item Standard
Voltage setting (at 20C [68F]) 14.7 V 0.3 V
1 - Ammeter.
2 - Switch.
3 - Voltmeter.
4 - Battery (12 volts).
4. Testing output characteristics.
Disconnect the earth lead from the negative terminal of the battery. Con-
nect one ammeter lead to the B terminal of the alternator and the other lead
to the positive terminal of the battery. Connect one voltmeter lead to the
B terminal and the other lead to earth; then connect the earth (negative)
lead of the battery. Start the engine and switch on all the electrical loads.
Increase the engine revs and measure the maximum output current at the
specified alternator speed, when the voltmeter reading is 13.5 volts.
Table 90
1 - Ammeter.
2 - Battery charging warning light.
3 - Switch.
4 - Battery.
30-110
Method of intervention
Disassembly
1. Disconnect the battery leads, disconnect the lead from terminal B of the
alternator, then disconnect the wiring connector from the alternator.
Loosen the mounting screws, move the alternator towards the engine and
remove the drivebelt.
Remove the alternator.
Fig. 376
Refitting
1. Locate the alternator. Fit the adjustment screw to hold the alternator in
position.
Locate the drivebelt on the pulley. Move the alternator away from the en-
gine to tension the drivebelt.
Tighten the screws.
Fig. 377
2. Fit the adjuster screw to hold the alternator in position.
Table 91
A - Apply a force of 10 kgf (22 1bf) [98 N] midway between the crankshaft
pulley and the alternator pulley.
B - Adjustment screw.
Fig. 378
30-111
Method of intervention
30.2.12 - Alternator
Disassembly
Fig. 380
30-112
Method of intervention
2. Removal of the pulley.
Hold the rotor assembly in a vice by using thick cloth as padding, as shown
in the figure. Remove the nut securing the pulley, and remove the pulley
and spacer. Remove the rotor assembly from the centre support bracket.
Fig. 381
3. Removal of the stator core and rectifier.
Unsolder the leads from the rectifier and remove the stator core.
m Unsolder the leads as quickly as possible to avoid damaging the
diodes in the rectifier.
Remove the screws that hold the rectifier in position and remove the recti-
fier.
1- Unsolder.
2 - Rectifier.
Fig. 382
Inspection
30-113
Method of intervention
Inspection procedure
1. Diodes.
Test the resistance between the diode and heat sink. Using an ohmmeter,
first touch the diode with the positive (+) probe, then with the negative ( )
probe. If the resistance is infinite in both cases, the diode circuit is open. If
it is nearly zero in both cases, the diode is shorted. Repeat this test on all
the remaining diodes.
m If any of the diodes are open or shorted, renew the rectifier.
Fig. 384
2. Field coil.
Test for continuity between the slip rings as shown in the figure.
m No continuity shows there is an open circuit in the field coil. Renew
the field coil.
Fig. 385
3. Test for electrical continuity between the slip ring and shaft (or core), as
shown in the figure.
m The absence of continuity indicates there is a earthed circuit in the
field coil. Renew the field coil.
Fig. 386
4. Stator core.
Test for continuity between the leads, as shown in the figure.
m The absence of continuity indicates there is an open circuit in the
stator core. Renew the stator core.
Fig. 387
30-114
Method of intervention
5. Test for continuity between each wire and the stator core, as shown in the
figure.
m The absence of continuity indicates there is a earthed circuit in the
stator core. Renew the stator core.
Fig. 388
6. Brushes.
Renew the brushes if they are worn down to or beyond the wear limit.
A - Wear limit.
Fig. 389
7. To remove the brushes from the brush holder for replacement, unsolder the
wires from the brushes, then remove the brushes and springs.
1 - Unsolder.
2 - Brush holder.
Fig. 390
8. Fit the new brushes in the brush holder and solder the wires to the brushes.
Fig. 391
30-115
Method of intervention
Assembly
1. To assemble, reverse the disassembly steps and use the following proce-
dure:
the rear bearing has a groove for slip ring. Install the slip ring in this groove,
making sure the tab locates the deepest part of the groove.
to install a new rear bearing, position it with the grooved side facing the slip
rings of the rotor;
before installing the bearing in the rear bracket, heat the bracket;
before installing the rotor in the rear bracket, insert a bent wire tool into the
hole in the rear bracket to lift the brushes clear of the slip rings. Remove the
tool after the rotor has been installed in position.
1 - Bent wire tool.
2 - Brushes.
3 - Rear bracket.
Fig. 392
Fig. 393
3. Remove nut (2) securing the cover of the electromagnet.
Fig. 394
30-116
Method of intervention
4. Withdraw starter control contact (3).
Fig. 395
5. Disconnect second power lead (4).
See para. 30.7.2 - Transmission oil filte... - page 30-244
Fig. 396
6. Remove the two starter motor retaining screws (5).
Fig. 397
7. Remove starter motor (6).
Fig. 398
30-117
Method of intervention
Refitting
1. Refitting is the reverse of removal.
Item Standard
Model M2T56272 M2T50381
Nominal output, V - kW 12 - 2.0 12 - 1.6
No-load characteristics Voltage at the terminals, V 11 11.5
Current draw, A 130 maximum 100 maximum
Speed (rpm) 3850 minimum 3000 minimum
30-118
Method of intervention
4. Solenoid
Disconnect the wiring connector from the M terminal of the solenoid. Con-
nect the solenoid to a 12 volt battery with a switch, as shown in the figure,
to test the pull-in coil. Close the switch to see if the pinion shifts.
m If the pinion fails to shift, the solenoid is faulty.
m Due to the amount of current being passed through the solenoid
series winding, this test must be performed within 10 seconds.
1 - Battery (12 volt).
2 - Connector disconnected.
Fig. 401
5. Connect the solenoid to a 12 volt battery with a switch, as shown in the
figure, to test the hold-in coil. Close the switch and pull the pinion away
from the commutator end by hand. Release the pinion to see if it remains
stationary.
m If the pinion returns, the solenoid is faulty.
m Due to the amount of current being passed through the solenoid
series winding, this test must be performed within 10 seconds.
1 - Battery (12 volt).
2 - Connector disconnected.
Fig. 402
6. Connect the solenoid to a 12 volt battery with a switch, as shown in the
figure, to test the pinion return. Close the switch and pull the pinion away
from the commutator end by hand. Release the pinion to see if it returns
immediately when released.
m If the pinion fails to return, the solenoid is faulty.
m Due to the amount of current being passed through the solenoid
series winding, this test must be performed within 10 seconds.
1 - Battery (12 volt).
2 - Connector disconnected.
Fig. 403
7. Removal.
Disconnect the battery leads. Disconnect the negative ( ) lead first. Dis-
connect lead (1) from the starter motor. Loosen the two retaining screws (2)
and remove the starter motor (3).
Fig. 404
30-119
Method of intervention
Refitting
1. Refitting is the reverse of removal.
ning.
30-120
Method of intervention
2. Ball.
The ball at the end of the armature serves as a thrust bearing. When the
armature is removed, the ball may remain attached to the end with grease.
m Take care not to lose the ball.
Fig. 406
Test
Armature
1. Coil shortcircuit test.
Position the armature on a shortcircuit tester (growler). Hold an iron bar
parallel to the armature and slowly turn the latter by hand.
m If the iron bar vibrates or is attracted towards the armature, this
means the armature coil is short circuiting and must be renewed.
Fig. 407
2. Coil earth test.
Test for continuity between the commutator and the shaft (or core).
m If there is continuity, this means that the coil is connected to earth
and the armature must be renewed.
Fig. 408
3. Commutator test.
Measure the commutator run-out using a dial gauge.
Table 93
Limit
Commutator run-out 0.1 mm (0.004 in)
m If the run-out exceeds the indicated tolerance limit, lightly skim the
commutator on a lathe so that the outside diameter is within the
specifications.
Fig. 409
m If the surface of the commutator is rough or has steps worn into it,
smooth using fine grade glasspaper (# 300 500).
30-121
Method of intervention
4. Measure the outside diameter of the commutator.
Table 94
Fig. 410
5. Measure the depth of the slots between the commutator segments.
Table 95
Limit
Commutator run-out 0.1 mm (0.004 in)
m If the depth is less that the specified tolerance limit, recut the slots to
depth of 0.4 0.6 mm. (0.016-0.024 inches).
Fig. 411
Field coil
1. Field coil interruption test.
Test for continuity between the terminal conductor and each of the brushes.
m If there is no continuity, this means the field coil circuit is interrupted.
In this case the yoke must be renewed.
Fig. 412
2. Coil earth test.
Test for continuity between the yoke and each of the brushes. If there is
continuity, this means the coil is connected to earth and must be checked
to see if the insulation is defective.
m Renew the yoke assembly if it cannot be repaired.
Fig. 413
30-122
Method of intervention
Brushes and brush gear
1. Brushes worn.
Measure the length of the brushes. If the length is below the specified toler-
ance limit, renew the brush.
Table 96
m If the brush is worn unevenly or has rough contact face, repair using
fine grade glasspaper (#300-500).
Fig. 414
2. Brush spring force.
Whenever a new brush is fitted, it is necessary to test the force of the
spring. Pull the spring brush with a strain gauge and read the load value at
the point where the spring becomes detached from the brush.
Table 97
m Renew the spring if the force is less than the specified limit. Fig. 415
Fig. 416
30-123
Method of intervention
Overrunning clutch
1. Check that the pinion shaft runs smoothly when turned clockwise (normal
direction of rotation) and that it locks up when turned anticlockwise.
m If the pinion shaft does not function correctly, renew the overrunning
clutch.
Fig. 417
30-124
Method of intervention
Checking and adjustment of the pinion clearance
1. Connect the starter motor to the battery as shown in the figure. The pinion
will move outwards and rotate slowly. Then remove the connector of termi-
nal M to stop the starter motor.
Fig. 419
2. Push the pinion shaft gently towards the armature and measure the axial
movement, which corresponds to the pinion clearance.
If the pinion clearance is not within the prescribed tolerance limits of 0.5-
2.0 mm (0.02 0.08 in.), adjust by increasing or decreasing the number of
gaskets on the field magnet (adding gaskets reduces the pinion clearance).
It may be necessary to renew the lever in order to obtain the correct pinion
clearance.
Table 98
Limit
Pinion clearance 0.5 mm - 2.0 mm (0.02 in - 0.08 in) Fig. 420
m Do not excite the field magnet for more than 10 seconds to avoid
overheating.
No-load test
1. When the pinion clearance has been correctly adjusted, connect an am-
meter and a voltmeter between the starter motor and the battery as shown
in the figure, then check the no-load characteristics of the starter motor.
Table 99
m Use the thickest possible cables. Tighten all the terminals securely.
Fig. 421
1. Ammeter.
2. Switch.
3. Starter motor.
4. Voltmeter.
5. Battery.
30-125
Method of intervention
Field magnet
1. Carry out the following continuity tests. If the field magnet fails any of these
tests, it should be renewed.
Check for interruptions in the coil circuit. There should be continuity be-
tween terminals S and M and between terminal S and earth (casing).
Check for poor contacts. There should be not be continuity between termi-
nals B and M.
Fig. 422
30-126
Method of intervention
30.3 - D0 - Transmission
30.3.1 - Clutch plate
Removal
1. Insert a suitable dowel (1) in the centre hole of the clutch assembly, then
attach the clutch assembly to a hoist (2).
Fig. 423
2. Remove the six screws (3).
m Loosen the six screws (3) gradually in stages a criss-cross se-
quence.
Fig. 424
3. Remove complete clutch assembly (4).
Fig. 425
4. Remove clutch plate (5)
Fig. 426
Refitting
Refitting is the reverse of removal.
30-127
Method of intervention
30.3.2 - Checking clutch plate wear
1. Check that the thickness of clutch plate (1) is within the prescribed toler-
ance limits and there is no sign of burning.
Clutch plate thickness:
- standard measurement: 10 0.3 mm
- limit measurement: 7.5 mm
Fig. 427
Fig. 428
2. Remove screws (3) securing the clutch release forks, then remove the
clutch release bearing assembly (4).
Fig. 429
3. Using a suitable drift, separate main clutch release bearing (5) from sleeve
(6).
Fig. 430
30-128
Method of intervention
4. Using a suitable drift, remove ring (7) from bearing (8) and bearing (8) from
sleeve (9).
Fig. 431
5. Remove the two thrust pins (10) from each of the two release forks.
m Check that the pins are not excessively worn or deformed and re-
new them if necessary.
Fig. 432
Refitting
1. Refitting is the reverse of removal.
m Grease the sleeve support.
Fit release bearing assembly (4) and locate fork pins (10) in their respective
housings on the sleeves.
Push sleeves (6) and (9) as far as they will go towards the transmission,
then, using a suitable installation tool, fit release bearing (8).
m Grease sleeves (6) and (9).
Fig. 433
Fig. 434
30-129
Method of intervention
2. Withdraw pin (2) and relative fork (3).
m Note which way round fork (3) is installed.
Fig. 435
3. Remove lock pin (4) securing the tie-rod of the main clutch release fork.
Fig. 436
4. Withdraw pin (5) and relative fork (6).
m Note which way round fork (6) is installed.
Fig. 437
5. Looking at the clutch housing from the front end, main clutch release fork
(6) is the smaller of the two forks and is located to the rear of PTO clutch
release fork (3).
Fig. 438
30-130
Method of intervention
Refitting
Refitting is the reverse of removal.
30.3.5 - Clutch housing
Removal
1. Remove sound-absorbing panels (1).
Fig. 439
2. Remove the brake tie-rod cotter pins (2) on both sides.
Fig. 440
3. Remove the four screws (3) and remove footplate support brackets (4).
Fig. 441
4. Disconnect rear wiring harness (5).
Fig. 442
30-131
Method of intervention
5. Disconnect oil supply pipe (6) to the rear lift.
Fig. 443
6. Remove retaining screw (7), cotter pin (8) and remove gearshift linkage (9).
m Mark the relative positions of gear lever (10) and the gearshift link-
age.
m Recover the bush.
Fig. 444
7. Remove the two screws (11) and remove the support complete with shuttle
lever (12).
Fig. 445
8. Remove cotter pin (13) and remove shuttle tie-rod (14).
Fig. 446
30-132
Method of intervention
9. Remove the two cotter pins (15) and PTO tie-rod (16).
Fig. 447
10. Remove the two screws (17) and remove main gear lever (18).
Fig. 448
11. Remove the two cotter pins (19) and remove gearshift tie-rod (20).
Fig. 449
12. Unscrew fork retaining screw (21) but leave the fork in position.
Fig. 450
30-133
Method of intervention
13. Disconnect the PTO/gearbox lubrication pipe (22).
Fig. 451
14. Attach clutch housing (23) to a hoist.
Fig. 452
15. Remove the four screws (24) and lift the clutch housing clear so as to with-
draw the fork.
Fig. 453
16. Remove clutch housing (25).
Fig. 454
30-134
Method of intervention
Refitting
1. Refitting is the reverse of removal.
To avoid damaging the rod oil seals, remove support (26) but remember to
refit it before installing the fork.
Remember to install fork (27) before definitively joining the two transmis-
sion casings.
Fig. 455
Fig. 457
30-135
Method of intervention
3. Remove forward driving gear (3), then remove circlip (4).
Fig. 458
4. Remove synchronizer (5).
Fig. 459
5. Remove circlip (6) and remove reverse driving gear (7).
Fig. 460
6. Only if necessary:
Remove inner race (8) of roller cage (9), the remove circlip (10) and remove
roller cage (9).
Fig. 461
30-136
Method of intervention
Assembly
1. To assemble, follow the disassembly steps in reverse order.
Fig. 463
Assembly
1. To assemble, follow the disassembly steps in reverse order.
30-137
Method of intervention
30.3.8 - Disassembly of the secondary shaft
Fig. 465
2. Remove 1st speed driven gear (2), then remove driver ring (3) from gear
(2).
Fig. 466
30-138
Method of intervention
3. Remove needle roller bearing (4) and remove circlip (5).
Fig. 467
4. Remove synchronizer (6) and friction ring (7).
Fig. 468
5. Remove circlip (8) and 2nd speed driven gear (9).
Fig. 469
6. Remove thrust plate (10) and remove circlip (11).
m Note which way round thrust plate (10) is installed.
Fig. 470
7. Remove the thrust plate (12) and the 3rd speed driven gear (13).
m Note which way round the thrust plate (12) is installed.
Fig. 471
30-139
Method of intervention
8. Remove circlip (14) and remove synchronizer (15) complete with driver ring
(16).
Fig. 472
9. Remove driver ring (17) and remove circlip (18).
Fig. 473
10. Remove 4th speed driven gear (19) and remove circlip (20).
Fig. 474
11. Remove spacer (21); then remove roller cage (22).
Fig. 475
12. Position output shaft (23) under a press and remove bearing (24).
Fig. 476
30-140
Method of intervention
Assembly
1. To assemble, follow the disassembly steps in reverse order.
2. Separate the clutch housing from the transmission and remove union (1).
m Renew the copper washers on reassembly.
Fig. 477
3. Remove the two screws (2) and remove bracket (3), then remove pivot pin
(4) and rotate 4WD control lever (5).
Fig. 478
4. Remove screws (6), attach the gearbox/shuttle (7) assembly to a hoist and
remove it.
Fig. 479
5. Remove the two seals (8) of the range gear selector rod and the PTO
speed selector rod.
m Remove all traces of paint from the selector rods to prevent damage
to the seals during reassembly.
Fig. 480
30-141
Method of intervention
Refitting
Refitting is the reverse of removal.
Carry out the following procedures:
Procedure 3
l Apply a continuous bead of sealant to the contact surfaces of the transmis-
sion casing and the gearbox/shuttle assembly.
l Surfaces: Loctite 510
Fig. 481
Procedure 3
l Install the gearbox/shuttle assembly and secure it with screws (6).
l If the clutch housing is not to be installed immediately, fit the spacers A
on the clutch housing studs and secure them in position with nuts to ensure
perfect adhesion between the mating surfaces.
Fig. 482
Procedure 4
l Using the installation tool T3, fit previously removed seals (8).
Fig. 483
Fig. 484
30-142
Method of intervention
3. Remove screws (4) and plate (5), then remove pin (6), springs (7) and balls
(8).
Fig. 485
4. Remove cover (9).
Fig. 486
5. Drill cover (10) and remove it using a slide hammer puller.
m Clean all traces of old sealant from the cover seating.
m Renew the cover on reassembly.
Fig. 487
6. Remove circlips (11) and (12) securing the main shaft and secondary shaft.
Fig. 488
7. Remove oil seal (13) and remove circlip (14).
Fig. 489
30-143
Method of intervention
8. Remove circlip (15) and spacer (16).
Fig. 490
9. Using a copper bar and a soft-faced mallet, simultaneously drive out the
input, primary and secondary shafts, tapping each in turn alternately.
Fig. 491
10. Remove the three circlips (17) and withdraw bearings (18).
Fig. 492
11. Remove the five oil seals (19).
Fig. 493
30-144
Method of intervention
Assembly
To assemble, follow the disassembly steps in reverse order.
Carry out the following procedures:
Procedure 3
l Apply a bead of sealant to the transmission casing.
l Transmission casing: Loctite 510
Fig. 494
Procedure 4
l Apply a bead of sealant to the seating of cover (10).
l Cover: Loctite 601
l Locate the cover and secure in position by tapping it in the centre.
Fig. 495
Procedure 8
l Insert all the shafts and forks simultaneously and, using a soft-faced mallet,
tap each shaft in succession to gradually drive them up against the bear-
ings in the gearbox casing.
Fig. 496
Procedure 8
l Adjust the position of the gear selector forks so that they positioned central-
ly relative to the synchronizer ring and secure them by tightening nuts (20).
l Nuts: Loctite 270
l Nuts: 90 to 105 Nm (66 to 77lb.ft.)
l Fit the nuts so that the flat sides face the forks.
Fig. 497
30-145
Method of intervention
Procedure 10
l Take care that the friction ring (21) of the 1st speed synchronizer does not
move out of position.
l Do not install the oil seals at this stage.
Fig. 498
30-146
Method of intervention
Removal
1. Remove screw (1) and remove washer (2).
Fig. 500
2. Move circlip (3) towards the rear of the transmission and drive shaft (4)
towards the front using a copper punch.
Fig. 501
3. Remove bearing (5) and remove shaft (4) complete with gear (6), circlip (3)
and bearing (7).
m Note which way round gear (6) is installed.
Fig. 502
4. Slide bearing (7) off shaft (4).
Fig. 503
30-147
Method of intervention
Refitting
Refitting is the reverse of removal.
l Apply Loctite to screw (1).
l Screw: Loctite 242
Fig. 504
2. Remove bearing holder sleeve (2).
Fig. 505
3. Remove circlip (3) securing the gearbox input shaft bearing.
Fig. 506
4. Withdraw shaft (4) from the rear end of the gearbox.
Fig. 507
30-148
Method of intervention
5. Remove oil seal (5).
m The oil seal must always be renewed using installer (6) whenever it
is removed.
Fig. 508
Refitting
Refitting is the reverse of removal.
30.3.13 - Bevel gear pair
30-149
Method of intervention
Removal
1. Remove screw (1) and remove spring (2) and ball (3).
Fig. 510
2. Remove nuts (4), remove fork (5) and rod (6).
Fig. 511
3. Remove bearing (8) on the opposite side to crown wheel (9) from differ-
ential housing (7). Then remove screws (10) and remove crown wheel (9)
complete with bearing (11).
Fig. 512
4. Remove the outer races of bearings (8) and (11) from differential supports
(12) and (13), while leaving in position the relative shims (14) and (15).
Fig. 513
5. Using a C spanner and a soft metal bar inserted between the driven gear
and the transmission casing, fully loosen nut (16).
m Renew nut (16) on reassembly.
Fig. 514
30-150
Method of intervention
6. Remove circlip (17).
Fig. 515
7. Move 4WD driving gear (18) towards the front of the transmission and re-
move key (19); then remove pinion (20).
Fig. 516
8. Remove the outer race of pinion bearing (21) and spacers (22) from the
transmission casing.
m Recover the spacers.
Fig. 517
9. Using a press, remove the remaining components of bearing (21) from pin-
ion (20).
Fig. 518
30-151
Method of intervention
Preparation for refitting
1. Mount new crown wheel (9) on differential housing (7) and secure it with
screws (10).
m Screws: 75 4 Nm (55 3 lb ft)
Fig. 519
2. Using a suitable drift, install the inner races of bearings (8) and (11).
Fig. 520
3. Remove shims to the value of 0.2 mm from each of the two shim packs (14)
and (15) of differential supports (12) and (13) and refit them in their respec-
tive supports along with the outer races of bearings (11) and (8).
m If it is not possible to identify the shim packs of the two sides, form
two shim packs: one 1.3 mm thick for the crown wheel side and the
other 1.8 mm thick for the opposite side.
Fig. 521
Refitting
1. Before refitting, see the various bevel gear pair adjustment procedures:
See para. 30.3.20 - Adjustment of the beve... - page 30-162
Fig. 522
30-152
Method of intervention
2. Insert ball (3), spring (2) and tighten screw (1).
m Renew the copper washers.
Fig. 523
3. Adjust the position of fork (5) so that the selector gear is positioned cen-
trally relative to the corresponding gear when the selector rod is in the L
range position. Tighten nuts (4) to secure in position.
m Nuts: 50 to 105 Nm (37 77.4 lb ft)
m Nuts: Loctite 270
Fig. 524
Fig. 525
2. Using a soft metal bar as a punch, drive out shaft (3) complete with the
bearing and remove sleeve (4) from the transmission casing; then remove
bearing (5) from shaft (3).
Fig. 526
30-153
Method of intervention
3. Remove circlip (6) and remove 4WD driven gear (8) and spacer (7).
Fig. 527
4. Remove circlip (9) and move shaft (10) towards the rear of the transmission
casing. Remove circlip (11) and withdraw the complete shaft assembly (10)
towards the front of the transmission.
Fig. 528
5. Remove circlip (12) and gear (13), then remove bearing (14).
Fig. 529
6. Remove bearing (15).
Fig. 530
30-154
Method of intervention
Assembly
1. To assemble, follow the disassembly steps in reverse order.
m Lubricate the lips of oil seal (2).
m Oil seal: transmission oil.
Fig. 531
Fig. 532
2. Remove front part of synchronizer (2).
Fig. 533
3. Remove circlip (3) securing the synchronizer.
Fig. 534
30-155
Method of intervention
4. Remove set screw (4), then remove the selector fork-synchronizer assem-
bly (5) and bronze crown (6).
Fig. 535
5. Remove cover (7 ) and remove the spring and ball (8) from the relative gear
selector rod.
Fig. 536
6. Remove creeper interlock plunger (9) after removing the relative plug.
Fig. 537
7. Remove circlip (10) securing the synchronizer gear.
Fig. 538
30-156
Method of intervention
8. Loosen the nut and locknut of selector fork (11), so that the fork may be
shifted forwards to allow removal of the synchronizer gear.
Fig. 539
9. Renew synchronizer (12).
Fig. 540
Refitting
1. Refitting is the reverse of removal.
m During reassembly, take care to install the selector fork the right way round, positioning it centrally relative to the syn-
chronizer ring.
m Nut and locknut: Loctite 243 threadlocker.
Fig. 541
2. Using a suitable drift, drive out shaft (3).
Fig. 542
30-157
Method of intervention
3. Remove roller cage (4).
Fig. 543
Refitting
Refitting is the reverse of removal.
30.3.17 - Disassembly of the PTO output shaft.
Disassembly
1. Remove circlip (2) from shaft (1) and remove bearing (3).
Fig. 544
Assembly
To assemble, follow the disassembly steps in reverse order. Carry out the following procedures:
30.3.18 - Removal of the PTO output shaft
Removal
1. Remove screw (1) and remove spring (2) and ball (3).
Fig. 545
2. Remove nuts (4) and remove fork (5).
Fig. 546
30-158
Method of intervention
3. Remove oil seal (6) and remove circlip (7).
Fig. 547
4. Move circlip (8) towards the front of the transmission. Using a suitable tool,
partially withdraw PTO shaft (9).
Fig. 548
5. Finally remove circlip (8) and remove PTO shaft (9).
m In some cases bearing (10) may remain on shaft (9). Remove it us-
ing gear (11).
m Recover shims (12), spacer (13) and gear (14).
Fig. 549
6. Remove bearing (15) from PTO shaft (9).
Fig. 550
30-159
Method of intervention
Refitting
1. To assemble, follow the disassembly steps in reverse order.
m If PTO shaft (9), bearings (10) and (15) or transmission casing (16)
are to be renewed, form a shim pack to be installed between PTO
shaft (9) and the front bearing (10) to obtain play of 0.05 to 0.15 mm.
Fig. 551
2. Adjust the position of the PTO speed selector fork so that, when selector
rod (17) is in the 1000 rpm position, selector gear (11) is positioned cen-
trally relative to the gear (18).
m Tighten nuts (4) to secure in position.
m Nuts: Loctite 270
m Nuts: 90 to 105 Nm (6677 lb.ft.)
m Fit the nuts so that the flat sides face the forks.
Fig. 552
Fig. 553
30-160
Method of intervention
2. Release the inner parking brake cable from clip (3).
Fig. 554
3. Remove the four retaining screws (6) and remove parking brake lever (7).
Fig. 555
4. Withdraw cotter pin (8).
Fig. 556
5. Remove the pin securing the cable to lever (9) and relative circlip (10).
Fig. 557
30-161
Method of intervention
6. Disconnect the parking brake cable from lever (11).
Fig. 558
Refitting
1. Refitting is the reverse of removal.
m After connecting the control cable, check that the parking brake lever has three notches of free play.
Fig. 559
2. Position a dial gauge with magnetic stand A on the differential support (2)
of the crown wheel side and set it to zero on the head of the differential,
while using a lever to force the differential towards the opposite side to the
crown wheel.
Fig. 560
3. Force the differential towards the crown wheel side and measure the end
float. Add 0.1 mm to the measured end float to determine the thickness of
the shims to be installed under the bearing (4) on the opposite side to the
crown wheel.
m Repeat the measurement procedure a number of times.
Fig. 561
30-162
Method of intervention
4. Remove flange (3) on the opposite to the crown wheel and install a shim
pack (5) of the thickness calculated in the previous step. Refit differential
support (3) to the transmission casing.
Fig. 562
5. Wind a cord around the 122 mm section of the differential housing and,
using a spring dynamometer T5 (code 5.9030.529.0), measure the rolling
resistance torque of differential (1) to check the correct preloading of the
differential bearings.
m Force required to maintain steady rotation: 2.5 to 4.0 kg
Fig. 563
Fig. 564
2. Install pinion (6) complete with the bearing in the transmission casing and
drive it into its seating.
mMake a note of the value E stamped on a tooth of pinion (6) (in this
example + 0.3 mm).
Temporarily fit 4WD gear (7) and nut (8).
m Tighten the nut to eliminate bearing play.
Fig. 565
3. Install differential (1) complete with supports (2) and (3), and then fix the
supports.
m While tightening the screws, check that there is clearance between
the differential and pinion (6). If the differential is tight up against the
pinion, adjust the two shim packs by reducing the shim thickness on
the crown wheel side and increasing the thickness on the opposite
side.
Fig. 566
30-163
Method of intervention
4. Use a feeler gauge to measure the distance D between the end face of
pinion (20) and the 122 mm section of the differential housing (in this
example 2.95 mm).
Calculate the value R by adding value E stamped on the tooth of pinion
(20) to the theoretical value of 2.00 mm.
If E is positive, as in the example shown in figure, add it to the theoretical
value of 2.00 mm.
R = 2.00 + E
i.e.
R = 2.00 + 0.30 = 2.30 Fig. 567
If E is negative, subtract it from the theoretical value of 2.00 mm.
R = 2.00 - E
i.e
R = 2.00 - 0.30 = 1.70
If the measured value D differs from the calculated value R, calculate the
difference between D and R.
The resulting value S is the shim thickness to be installed under the bear-
ing of pinion (6).
Formula: S = D - R
which in our example gives: S = 2.95 2.30 = 0.65 mm
5. Remove differential (1) and pinion (6) complete with the bearing. Fit the
calculated shim pack S (10) on bearing (9) and install in the transmission
casing.
m Fit 4WD driving gear (7), nut (8) and the driven range gear (11) on
pinion shaft (6).
Fig. 568
6. Secure bearing (9) in position with circlip (12) selected from the available
sizes.
Select the circlip by applying the following formula:
Circlip thickness = A
Fixed dimension = R
Shim thickness = S
A=RS
which in our example gives: A = 3.50 0.65 = 2.85 mm
A 2.80 mm thick circlip is therefore required.
Fig. 569
7. Insert key (13) and, using wrench T6 (code 5.9030.964.0), tighten nut (8).
m Nut: 14020 Nm (10314.7 lb.ft.)
m Nut: Loctite 270
Fig. 570
30-164
Method of intervention
8. Stake nut (8) at three points.
Fig. 571
Fig. 572
2. Position a dial gauge B on a magnetic stand with the contact point per-
pendicular to the side of a tooth on the external diameter of the crown
wheel. Preload the gauge by approx. 3 mm and measure the backlash Z
between the pinion and crown wheel by turning crown wheel (15) in both
directions.
m Normal backlash: 0.10 to 0.15 mm
m Take four measurements 90 apart and calculate the average.
Fig. 573
3. If the backlash Z is less than 0.10 mm, transfer shims from pack S1
(crown wheel side) to pack S2 (opposite side to the crown wheel). If the
backlash Z is greater than 0.15 mm, transfer shims from shim pack S1
(crown wheel side) to shim pack S2 (opposite side to crown wheel).
m The sum total thickness of shim packs S1 and S2 should not be
altered from the value determined by testing the rolling resistance
of the differential.
Recheck backlash Z and, if necessary, continue to adjust the shims until
the backlash is within the specified tolerance limits.
Fig. 574
4. Finally tighten down screws (14) securing differential supports (2) and (3).
m Screws: 211 Nm (15.50.7 lb.ft.)
m Screws: Loctite 242
30-165
Method of intervention
30.4 - E0 - Rear axle
30.4.1 - Left-hand rear axle
Removal
1. DANGER
Disconnect the lead from the battery negative terminal (-) and apply the parking brake.
2. Loosen clamps (1) and disconnect sleeve (2) from one of the pipes (3).
Fig. 575
3. Remove nuts (4) and disconnect plate (5) from the transmission.
Move the stand (A) positioned under the rear axle under the bar (B).
Fig. 576
4. Remove the platform.
Remove the four screws (6) and remove platform support (7) and rear
safety roll-bar.
Fig. 577
5. Remove the two screws (8), nut (9) and remove oil suction pipe (10).
m Recover gasket (11).
Fig. 578
30-166
Method of intervention
6. Remove all the nuts (12), remove bracket (13) and spring (14), then remove
parking brake cable retaining plate (15).
Fig. 579
7. Attach rear axle (16) to a hoist and take up the slack in the lifting slings/
ropes, then remove axle assembly (16).
Fig. 580
Refitting
Refitting is the reverse of removal.
l Adjust the brake pedals and the parking brake lever.
Carry out the following procedures:
Procedures 6-7
l Mating faces: Loctite 510
Fig. 581
Procedure 6
l Screws and nuts: 40.5 to 44.8 Nm (30 33 lb.ft.)
Procedure 5
l Bleed the air from the braking system.
l Fill the transmission with the required quantity of oil
30-167
Method of intervention
30.4.2 - Disassembly of LH/RH rear axle
Fig. 583
2. Using a puller, remove hub (2).
Fig. 584
30-168
Method of intervention
3. Remove bearing (3) and ring (4) complete with oil seal (5).
Fig. 585
4. Remove oil seal (5) from ring (4).
m Renew oil seal (5) on reassembly.
m Note which way round oil seal (5) is installed.
Fig. 586
5. Withdraw gear (7) from axle housing (6).
Fig. 587
6. Remove circlip (8) and remove bearing (9).
Fig. 588
7. Remove circlip (10) and withdraw complete shaft (11).
m To withdraw the shaft, pull it towards you while tapping it with a soft-
faced mallet.
Fig. 589
30-169
Method of intervention
8. Remove circlip (12) and withdraw bearing (13).
Fig. 590
9. Remove circlip (14), spacer (15) and remove bearing (16).
Fig. 591
Assembly
1. Using a press, install bearing (16) on shaft (11), then fit spacer (15) and
secure with circlip (14).
Fig. 592
2. Install bearing (3) in axle housing (6) then fit oil seal (5) to ring (4).
m Take care to install the oil seal the right way round.
Fig. 593
3. Position complete ring assembly (4) in the axle housing and, using a suit-
able tool, drive it into its seating.
m Fill the grooves in ring (4) with sealant.
m Ring grooves: Silastic
m Lubricate the lips of the oil seal.
m Oil seal: Oil
Fig. 594
30-170
Method of intervention
4. Fit shaft (11) in axle housing(6) and secure it in position with circlip (10).
Fig. 595
5. Install bearing (9) and secure it in position with circlip (8).
Fig. 596
6. Install gear (7) in axle housing (6).
Fig. 597
7. Position axle housing (6) under a press and install hub (2), driving it up
against bearing (9).
m To facilitate installation, place spacers A to a thickness of 20 mm
between the surface of the press and gear (7) to prevent hub (6)
getting stuck in the gear.
Fig. 598
8. Using a suitable drift, install bearing (13) and secure in position with circlip
(12).
Fig. 599
30-171
Method of intervention
9. Tighten nut (1).
m Nut: 340-420 Nm (250.5309.5 lb.ft.)
m To facilitate tightening of the nut, insert a spring pin in the teeth of
gear (7) and rotate the input shaft until it locks up.
m Remove the spring pin.
Fig. 600
10. Stake nut (1) in correspondence with the slot in hub (2).
Fig. 601
30-172
Method of intervention
Fig. 603
30-173
Method of intervention
2. Remove differential lock engagement sleeve (3) and shoe (4).
Fig. 604
3. Remove screws (5) and remove RH differential support (6).
m Do not use automatic screwdrivers as this could damage the hex
heads of the screws.
m Support the differential during removal of the support.
m Mark the RH support to avoid confusion on reassembly.
Fig. 605
4. Remove differential assembly (7).
Fig. 606
30-174
Method of intervention
Refitting
1. Refitting is the reverse of removal.
m Screws: 21 1 Nm (15.5 0.7 lb ft)
Fig. 607
2. Remove thrust washer (3) and side gear (4).
Fig. 608
3. Withdraw spring pin (5).
Fig. 609
4. Withdraw the pin (6), planet pinions (7), thrust washers (8) and the second
side gear (9) with its thrust washer (10).
Fig. 610
30-175
Method of intervention
Assembly
1. To assemble, follow the disassembly steps in reverse order.
m Screws: 75 4 Nm (55 3 lb ft)
m Thrust washers: transmission oil
Fig. 611
2. m Insert the spring pin (5) so that the end lies approx. 1 mm below
the the face of the differential housing to which the crown wheel is
mounted.
m Thrust washers: transmission oil
Fig. 612
Fig. 613
2. Remove plain steel disc (2) and friction disc (3).
m Note which way round plain steel disc (2) is installed.
Fig. 614
30-176
Method of intervention
3. Loosen off fully brake operating tie-rod (4) and remove nut (5) and spring
(6).
Fig. 615
4. Remove braking device (7) and the last friction disc (8).
Fig. 616
Only if necessary
1. Remove boot (9) and replace it with a new one.
Fig. 617
Refitting
1. Refitting is the reverse of removal.
m Adjust travel of brake pedals.
30-177
Method of intervention
30.5 - F0 - Front axle
30.5.1 - Front support
Removal
1. Disconnect the pipes to the front hydraulic service couplers (1).
Fig. 618
2. Disconnect differential lock pipe (2) and the two power steering pipes (3).
Fig. 619
3. Position a stand under gearbox (4).
Fig. 620
4. Remove radiator bracket screws (5) on both sides.
Fig. 621
30-178
Method of intervention
5. Disconnect the lower connection pipe of front lift control valve (6).
Fig. 622
6. Remove the two metal straps (7) and move the pipe to one side.
Fig. 623
7. Remove metal strap (8) on the RH side.
Fig. 624
8. Disconnect oil supply pipe (9) from the holding valve and oil return pipe (10)
from the PTO clutch.
Fig. 625
30-179
Method of intervention
9. Disconnect front PTO lubrication pipe (11) on the LH side.
Fig. 626
10. Remove on the RH side the two screws and the two nuts (12) connecting
the front engine support.
Fig. 627
11. Remove on the RH side the three screws and two nuts (13) connecting the
front engine support.
Fig. 628
12. On the RH side, disconnect PTO wiring harnesses (14).
Fig. 629
30-180
Method of intervention
13. Remove PTO solenoids (15).
m Recover the three O-rings.
Fig. 630
14. Fit two eyebolts to radiator bracket (16).
Fig. 631
15. Attach the front support to an overhead crane and remove front support
complete with axle (17).
m Proceed with caution to avoid damaging the PTO solenoid valve.
Fig. 632
30-181
Method of intervention
Refitting
1. Refitting is the reverse of removal.
m Take care to connect the PTO engagement connector to the first solenoid and the PTO brake connector to the second
solenoid.
2. Remove the two screws (1) securing the clamps, remove the five screws
(2) and remove the 4WD shaft shield (3).
Fig. 633
3. Disconnect steering pipes (4).
m Plug the pipes to prevent the ingress of dirt.
Fig. 634
4. Disconnect front differential lock control pipe (5).
m Plug the pipe to prevent the ingress of dirt.
Fig. 635
5. Unseat circlip (6) and withdraw pin (7).
Fig. 636
30-182
Method of intervention
6. Move sleeve (9) towards pinion (8) in order to release 4WD shaft (10).
Repeat the above procedure for the front sleeve.
m Take care not to get sleeve (9) stuck on the pinion teeth (8).
Fig. 637
7. Remove screws (11) and remove 4WD shaft (10) complete with centre sup-
port (12).
Fig. 638
8. Raise the front end of the tractor and position a stand A under the sump,
then remove the front wheels (13).
Fig. 639
9. Position a jack under the front axle; remove nuts (14) and washers (15) and
remove axle (16).
Fig. 640
30-183
Method of intervention
Refitting
1. Refitting is the reverse of removal.
m Fill the front axle with oil of the specified type and quantity.
Fig. 642
30-184
Method of intervention
2. Remove split pin (3) and loosen nut (4).
m Fit new split pins on reassembly.
Fig. 643
3. Using a soft mallet and nut (4) as a driving tool, disconnect pin (5) from
steering knuckle housing (6), then remove nut (4) and remove pin (5) from
the steering knuckle housing.
m Repeat the above operations to remove the pin on the opposite side.
Fig. 644
4. Remove the two unions (7).
m Renew the copper washers on reassembly.
Fig. 645
5. Using a hot air blower, heat one side of the piston to approx. 65 C and
removing steering arm (8).
Fig. 646
6. On both sides remove the two screws (9), remove end fitting (10), then
withdraw piston (11) complete with end fitting (12).
Fig. 647
30-185
Method of intervention
Refitting
1. Refitting is the reverse of removal.
m Take care to position ring (A) and ring (B) as shown in the figure.
m Nut (4): 25 Nm (18.4 lb ft)
m Steering arms (8): 131 - 145 Nm (96.5 - 107 lb ft).
m Steering arms (8): Loctite 242.
Fig. 648
Fig. 650
30-186
Method of intervention
2. Remove spacers (3), the shims (4) and the steering cylinder (5) from axle
housing (2).
Fig. 651
3. Remove O-ring (6), seal (7) and dust seal (8) from the end caps (9).
m Check the condition of O-ring (6) and renew it if necessary.
m Note which way round seal (7) is installed.
m Renew seal (7) and dust seal (8) on reassembly.
Fig. 652
4. Remove seal (11) and guide ring (12) from piston (10).
Fig. 653
30-187
Method of intervention
Assembly
1. To assemble, follow the disassembly steps in reverse order.
Wide version.
On both ends of the steering cylinder, install piston (10), spacer (3) and end
cap (9) and tighten screws (13).
m Note which way round seal (7) is installed.
m Renew seal (7) and dust seal (8) on reassembly.
m Surfaces (S): Silastic.
Fig. 654
2. Narrow version.
On both ends of the steering cylinder, install piston (10), spacer (3) and end
cap (9) and tighten screws (13).
m Note which way round seal (7) is installed.
m Renew seal (7) and dust seal (8) on reassembly.
m Surfaces (S): Silastic.
Fig. 655
Fig. 656
2. Position a jack under the front axle and remove nuts (1) and the two wash-
ers (2); apply a lever between front support (3) and front and rear axle sup-
ports (4) and remove the complete axle.
Fig. 657
30-188
Method of intervention
3. Remove axle shafts (5).
Fig. 658
4. Remove screw (6) and unions (7) and remove steering control pipes (8).
Fig. 659
5. Remove rear axle support (9) and spacer (10), then remove union (11) and
differential lock pipe (12).
m Renew the copper washers on reassembly.
Fig. 660
6. Remove screws (13) and remove the complete differential assembly (14).
m Check the condition of the O-ring (15). Renew it if distorted or dam-
aged.
Fig. 661
30-189
Method of intervention
Refitting
1. Refitting is the reverse of removal.
Fig. 663
30-190
Method of intervention
2. Detach spring (4) from fork (5) and remove sleeve (6) and shoes (7).
Fig. 664
3. Drive out spring pin (8) and remove, in order: washer (9), pin (10), complete
with washer (11), spring (12), fork (13) and spacer (14).
m Note which way round spring (12) is installed.
Fig. 665
4. Force out the differential lock piston (15) using a low pressure compressed
air jet.
m Carefully check the condition of O-ring (16); renew it distorted or
damaged.
Fig. 666
5. Remove circlip (17) on the crown wheel side and recover shims (18).
m Make a note of the total thickness of shim pack (18).
Fig. 667
6. Remove circlip (19) from the opposite side to the crown wheel and recover
shims (20).
m Make a note of the total thickness of shim pack (20).
Fig. 668
30-191
Method of intervention
7. Withdraw bearings (21) and (22) and remove the complete differential as-
sembly (23).
Fig. 669
8. Remove screws (24) and remove crown wheel (25).
Fig. 670
9. Remove the sun gear (28) and thrust washer (27) from differential housing
(26).
Fig. 671
10. Drive out spring pin (29) sufficiently to release pin (30) and withdraw pin
(30); then withdraw planet pinions (31) and relative washers (32).
Fig. 672
11. Remove side gear (33) and thrust washer (34) from differential housing
(26).
Fig. 673
30-192
Method of intervention
12. Using wrench (T), remove nut (35).
mRenew the nut on reassembly.
Remove spacer (36).
m Recover O-ring (37).
Fig. 674
13. Remove oil seal (38) and withdraw pinion (39).
m Renew the oil seal on reassembly.
Fig. 675
14. Remove the inner race of bearing (41) from differential support (40) and
withdraw the inner race of the bearing (42) from pinion shaft (39).
Fig. 676
15. Withdraw the outer races of bearings (41) and (42) from the differential
support (40).
m Recover shims (43) installed under the outer race of bearing (42).
Fig. 677
30-193
Method of intervention
Assembly
1. Install bearing (42) without shims (43) in differential support (40), and use a
depth gauge (A) to measure dimension X.
m To facilitate the measurement, use a pin (B) or a calibrated plate.
Fig. 678
2. Calculate the distance D of the axis of rotation of the differential from the
face of bearing (42) using the following formula:
D = X + B radius of crown wheel bearing (R)
Example:
- dimension X = 128.9 mm
- pin diameter B = 8.00
- radius of crown wheel bearing = 40.0 mm
D = 128.9 + 8.00 40.0 = 76.9 mm
Fig. 679
3. Note the dimension E stamped on the tooth tip. Remove outer race of
bearing (42) and differential support bearings (21) and (22); form a shim
pack S using the following formula:
S = D theoretical value E
where:
S =shim pack thickness
D = distance calculated in point 2.
theoretical value = 76.00
E = value stamped on tooth
Example 1 (positive E value): D = 76.90 mm E = 0.30 mm theoretical Fig. 680
value = 76.00 S = 76.90 76.00 0.30 = 0.60 mm Example 2 (negative E
value): D = 76.90 mm E = 0.30 mm theoretical value = 76.00 S = 76.90
76.00 + 0.30 = 1.20 mm
4. Install in differential support (40) shim pack (43), the outer race of bearing
(42) and the outer race of bearing (41).
Fig. 681
30-194
Method of intervention
5. Insert pinion (39) complete with the inner races of bearing (42) and bearing
(41).
Fig. 682
6. Fit O-ring (37) and spacer (36).
Fig. 683
7. Using tool (T), screw in nut (35) to seat the bearings, then back off by about
1/4 turn.
m Nut: Loctite 270
While tightening the nut, rotate pinion (39) in both directions and tap it light-
ly to help seat the bearings.
m Tighten nut (35) gradually until all pinion end float is eliminated, but
without preloading the bearings.
Fig. 684
8. Position thrust washer (34) and the side gear (33) in differential housing
(26).
m Washer: transmission oil
Fig. 685
9. Position planet pinions (31) with their thrust washers (32).
m Thrust washers: transmission oil
Insert pin (30) and secure it in position with spring pin (29).
m Insert the spring pin so that the end lies approx. 0.5 mm below the
face of the differential housing to which the crown wheel is mounted.
Fig. 686
30-195
Method of intervention
10. Locate side gear (28) and its thrust washer (27).
m Washer: transmission oil
Fit crown wheel (25) and tighten screws (24).
Fig. 687
11. Position the complete differential assembly (23) in support (40) and fit bear-
ing (22) on the opposite side to the crown wheel.
Fig. 688
12. Form shim pack (20) on the opposite side to the crown wheel by adding 0.2
mm to the thickness measured during disassembly.
Example:
measured thickness = 1.5 mm
new shim pack = 1.7 mm
Fit new shim pack (20) and secure with circlip (19).
Fig. 689
13. Fit crown wheel side bearing (21) in its seat in the differential housing.
m Check that both bearings are fully seated in the differential housing.
Fig. 690
14. Position a dial gauge F on a magnetic stand as shown with the contact
point perpendicular to the outer side of a tooth on the crown wheel. Preload
the gauge by approx. 2 mm and measure the backlash Z between the
pinion and crown wheel by turning differential (23) back and forth in both
directions.
m Check that bearing (22) on the opposite side to the crown wheel is
seated against the circlip.
m Normal backlash Z: 0.14 to 0.19 mm
m Take four measurements 90 apart and calculate the average.
Fig. 691
30-196
Method of intervention
15. Temporarily fit circlip (17) and, with a feeler gauge, measure the clearance
between circlip (17) and bearing (21) to determine the thickness of the shim
pack (18) to be installed under the circlip on the crown wheel side.
m Shim pack (18) should be thick enough to eliminate the end float of
differential (23).
Fit shim pack (18) and secure it with circlip (17).
Fig. 692
16. Insert differential lock piston (25) in differential support (40).
m O-ring: transmission oil
Fig. 693
17. Install the following components in the differential support in the order giv-
en: spacer (14), fork (13), spring (12), pin (10), washer (9) and secure with
spring pin (8).
m Take care to install spring (12) the right way round.
Fig. 694
18. Insert shoes (7) in fork (13) and insert the end of spring (12) in hole (A),
then fit sleeve (6).
Fig. 695
19. Using a suitable tool, fit oil seal (38) on differential support (40) and install
O-ring (3).
m O-ring: grease
Fig. 696
30-197
Method of intervention
30.5.7 - Propeller shaft - Front axle drive shaft
Removal
1. Remove the two front screws (1) and central screw (2) securing the cover.
Fig. 697
2. Remove the two rear screws (3) and remove cover (4).
Fig. 698
3. Unseat circlip (5) and drive out spring pin (6) from the front and rear ends
of the shaft.
Fig. 699
4. Move the sleeve towards pinion (7) and remove front axle drive shaft (8).
m Take care not to get the sleeve stuck on the pinion teeth.
Fig. 700
30-198
Method of intervention
Refitting
1. Refitting is the reverse of removal.
Fig. 701
2. Remove split pin (3) and loosen nut (4).
m Fit new split pins on reassembly.
Fig. 702
3. Using a soft faced mallet and nut (4) as a drift, detach pin (5) from steering
knuckle housing (6); remove nut (4) and remove pin (5) from the steering
knuckle housing. Remove screws (7) and finally remove complete plan-
etary reduction gear assembly (8).
Fig. 703
Refitting
1. Refitting is the reverse of removal.
Fill the front axle with oil of the specified type and quantity.
m Front axle: max. 4.8 l (1.3 gall).
30-199
Method of intervention
30.5.9 - Disassembly of the planetary reduction gear
Fig. 705
2. Check the condition of O-ring (2) and renew it if necessary.
Fig. 706
30-200
Method of intervention
3. Remove bearing (3) and remove crown wheel (4).
Fig. 707
4. Remove ring halves (5) and remove flange (6).
Fig. 708
5. Remove circlip (7) and withdraw bearing (8).
Fig. 709
6. Remove oil seal (9).
m Note which way round the oil seal is installed.
Fig. 710
7. Remove cover (10), remove circlip (11) and spacer (12).
Fig. 711
30-201
Method of intervention
8. Remove from stub axle housing (13) bearing (14) complete with gear (15)
and shaft (16); remove circlip (17).
m Mark gear (15) to avoid confusion on reassembly.
Fig. 712
9. Using a soft metal punch and a mallet, separate steering joint support (18)
from stub axle housing (13).
Fig. 713
10. Using a soft metal punch and a mallet, drive bearing (19) from stub axle
housing (13).
Fig. 714
11. Using a lever, prise out oil seal (20) then remove spacer (21) and bearing
(22).
Fig. 715
12. Remove O-ring (23) from steering joint support (18).
m Check the condition of the O-ring and renew it if distorted or dam-
aged.
Fig. 716
30-202
Method of intervention
13. Remove from steering joint support (18) bearings (24) and (25) complete
with gears (26) and (27).
Fig. 717
14. Separate bearings (14), (24) and (25) from the respective gears (15), (26)
and (27) , then recover spacers (28) from gear (27).
Fig. 718
Assembly
1. Fit gear (27) without shims (28) on bearing (25) and fit gears (15) and (26)
on the corresponding bearings (14) and (24).
Fig. 719
2. Fit complete gear assembly (26) and carefully drive it into its seating in
steering joint support (18); then fit gear (27) previously assembled without
the shims and seat it against gear (26).
Fig. 720
3. Using a depth gauge (A), measure distance (B) between the face of steer-
ing joint support (18) and the outer race of bearing (25). Calculate the thick-
ness of the spacers S to be inserted by applying the following formula: S
= B 0.3 mm.
Fig. 721
30-203
Method of intervention
4. Form shim pack (28) with thickness equal to calculated value S 0.04
mm; then install shim pack (28) under gear (27).
Fig. 722
5. Install bearing (22) and spacer (21) in stub axle housing (13).
Fig. 723
6. Using service tool T8, install oil seal (20) in stub axle housing (13).
m Before installing the oil seal, carefully clean and degrease the seat
of the seal in the stub axle housing and on the steering joint support.
m Do not lubricate the oil seal seat.
Fig. 724
7. After carrying out the above steps, reassemble following the disassembly
procedure in reverse order.
m Lubricate O-ring seal (2).
m O-ring: grease.
m Moisten surfaces S of the steering joint support with ethyl alcohol
to facilitate installation of the oil seal.
m Lubricate O-ring (23).
m O-ring: grease. Fig. 725
30-204
Method of intervention
30.6 - G0 - Bodywork - Cab - Platform
30.6.1 - Cab
Removal
1. Remove accelerator pedal (1).
Fig. 726
2. Remove the knob of 4WD lever (2).
Fig. 727
3. Remove the knob of creeper gear lever (3).
Fig. 728
4. Remove the two screws (4) securing the floor mat moulding.
Fig. 729
30-205
Method of intervention
5. Remove floor mat (5).
Fig. 730
6. Remove A/C valve assembly cover (6) secure with two screws on the LH
side.
Fig. 731
7. Remove the four screws (7) and remove oil filter bracket (8).
Fig. 732
8. Loosen clamp (9) and remove cab heating water pipe (10).
Fig. 733
30-206
Method of intervention
9. Disconnect A/C pipe (11) on LH side.
Fig. 734
10. Disconnect starter motor lead (12).
Fig. 735
11. Disconnect the two wiring connectors (13) on the LH side and remove cab
wiring fuses (14).
Fig. 736
12. Disconnect the parking brake cable by removing the cotter pin, pin (15) and
loosening the clamp securing gaiter (16) to release the outer cable.
Fig. 737
30-207
Method of intervention
13. Release the parking brake cable from metal strap (17).
Fig. 738
14. Disconnect the two wiring harnesses (18) for the rear lights.
m Do not remove the connector for the rear trailer lights from the brack-
et.
Fig. 739
15. Disconnect the two tie-rods of rear remote valves (19).
Fig. 740
16. Disconnect the two lift control tie-rods (20).
Fig. 741
30-208
Method of intervention
17. Remove lower cover (21) secured with two screws and side panels (22)
secured with four screws.
Fig. 742
18. Remove on both sides the four screws (23) securing the inside of the cab
to the footplate.
Fig. 743
19. Disconnect earth lead (24) under the cab.
Fig. 744
20. On both sides remove the two screws (25) to release the cab from the metal
guards.
Fig. 745
30-209
Method of intervention
21. Remove the two rear silent blocks (26).
Fig. 746
22. Disconnect the pipe from the A/C valve (27) on the RH side.
Fig. 747
23. Remove the three retaining screws and remove A/C pipe cover (28).
Fig. 748
24. Loosen clamp (29) and disconnect heater pipe (30).
Fig. 749
30-210
Method of intervention
25. Sling the top of the cab to a hoist and raise it about by 10 cm.
Fig. 750
26. On the LH side disconnect parking brake warning light connector (31) and
on the RH side disconnect front PTO pushbutton wiring connector (32).
Fig. 751
27. Raise the cab slowly and carefully remove it from the tractor.
m Help separate the lower part of the cab from the tractor with little
jolts.
Fig. 752
30-211
Method of intervention
Refitting
1. Refitting is the reverse of removal.
Fig. 753
2. Disconnect air cleaner clogging sensor (1).
Fig. 754
3. Disconnect LH and RH side light connectors (2) and (3).
Fig. 755
4. Disconnect the three-wire connector of LF front worklight (4) and the four-
wire connector of RH front worklight and horn (5).
Fig. 756
30-212
Method of intervention
5. Remove gas spring (6).
DANGER
Support the hood by hand during this operation to prevent it
from falling when the gas spring is removed.
Fig. 757
6. Remove the two screws and washers (7) on the RH and LH sides to release
the hood.
Fig. 758
7. Slide the hood forwards to remove it from the tractor.
Fig. 759
30-213
Method of intervention
Refitting
Refitting is the reverse of removal.
Engine hood support bracket
Removal
1. Remove the two upper front screws (8).
Fig. 760
2. Remove the four centre screws (9).
Fig. 761
3. Remove the two upper screws (10).
Fig. 762
4. Remove the two front screws (11).
Fig. 763
30-214
Method of intervention
5. Remove bracket (12).
Fig. 764
Refitting
1. Refitting is the reverse of removal.
Refit the two centre screws by positioning in the correct sequence: screw
(9), washer (13), asbestos washer (14), washer (13), bracket (12), asbes-
tos washer (14).
Fig. 765
2. Refit the two front screws by positioning in the correct sequence: screw
(11), washer (13), asbestos washer (14), washer (13), bracket (12), washer
(13), asbestos washer (14).
Fig. 766
Lower hood
Removal
1. Remove the battery.
2. T.H36.21.L0.01.00.00.01
3. Remove the two side screws (15) on both sides.
Fig. 767
30-215
Method of intervention
4. Remove lower hood (16).
Fig. 768
Refitting
1. Refitting is the reverse of removal.
Fig. 769
2. Remove nut (2).
m Recover the nut, washers, stud, pipe and other components.
Fig. 770
3. Remove the two hex socket screws (3) located on the underside of the
steps.
DANGER
Support the auxiliary fuel tank to prevent it from falling.
Fig. 771
4. Remove the steps assembly, leaving the auxiliary fuel tank attached to the tractor.
30-216
Method of intervention
Refitting
1. Refitting is the reverse of removal.
Fig. 772
2. Remove fenders (2).
Fig. 773
Refitting
1. Refitting is the reverse of removal.
Fig. 774
30-217
Method of intervention
2. Remove the two screws, disconnect the internal tie-rod (2) and remove
door lock (3).
Fig. 775
3. Remove one screw, disconnect tie-rod (4) and remove the manual door
opening control (5).
Fig. 776
4. Remove tie-rod (6).
Fig. 777
5. Remove two screws (7) and nut (8).
Fig. 778
30-218
Method of intervention
6. Remove the external lock complete with handle (9).
Fig. 779
Refitting
1. Refitting is the reverse of removal.
Fig. 780
2. Disconnect the five instrument wiring connectors (2).
Fig. 781
3. Remove instrument panel (3).
Fig. 782
30-219
Method of intervention
Refitting
1. Refitting is the reverse of removal.
Fig. 783
2. Remove pillar trim knob (2).
Fig. 784
3. Disconnect front and rear wiring connectors (3) and front and rear water
pipes (4).
Fig. 785
4. Remove pillar trim - screenwash reservoir (5).
Fig. 786
30-220
Method of intervention
Refitting
1. Refitting is the reverse of removal.
Fig. 787
2. Remove screw (4) and remove gear lever (5).
Fig. 788
3. Remove the two screws (6) and remove RH side panel (7).
Fig. 789
Refitting
1. Refitting is the reverse of removal.
30-221
Method of intervention
30.6.9 - Left-hand console
Removal
1. Remove screw (1) and remove knob (2) of the rear PTO control lever.
m Remove inner part (3) by rotating counterclockwise.
Fig. 790
2. Remove screw (4) and remove shuttle control lever (5).
Fig. 791
3. Remove the two screws (6) and remove LH side panel (7).
Fig. 792
30-222
Method of intervention
Refitting
1. Refitting is the reverse of removal.
Fig. 793
2. Unscrew lock nut (2).
Fig. 794
3. Withdraw metal outer sleeve (3) from the support slot.
Fig. 795
4. Unseat metal cable (4).
Fig. 796
30-223
Method of intervention
5. Disconnect wiring connector (5) and remove dashboard (6).
Fig. 797
Refitting
1. Refitting is the reverse of removal.
Fig. 798
2. Remove the four screws (2) and then remove centre console (3).
Fig. 799
Refitting
1. Refitting is the reverse of removal.
30-224
Method of intervention
30.6.12 - RH rear cab pillar trim
Removal
1. Remove retaining knob (1) of the cab pillar trim.
Fig. 800
2. Remove pillar trim (2).
Fig. 801
Refitting
1. Refitting is the reverse of removal.
Fig. 802
30-225
Method of intervention
2. Remove filter (3).
Fig. 803
Refitting
Refitting is the reverse of removal.
30.6.14 - Cab roof
Removal
1. Discharge the refrigerant from the A/C system.
Disconnect pipe (1) from the condenser.
Fig. 804
2. Unscrew the two retaining screws and remove pipe cover (2).
Fig. 805
3. Remove the two retaining screws for each and remove covers (3) on both
sides.
Fig. 806
30-226
Method of intervention
4. Remove the six screws and remove upper panel (4).
Fig. 807
5. Remove the six retaining screws and remove cab roof lining (5) from rear
of cab.
Fig. 808
6. Remove the three retaining screws and remove fuse assembly support (6).
Fig. 809
7. Disconnect rear wiper wiring connector (7).
Fig. 810
30-227
Method of intervention
8. Remove coolant pipes (8) on both sides.
Fig. 811
9. Remove evaporator condensate drain pipes (9) on both sides.
Fig. 812
10. Remove expansion valve pipe (10).
Fig. 813
11. Disconnect windscreen wiper wiring connector (11).
Fig. 814
30-228
Method of intervention
12. Disconnect the three earth leads (12).
Fig. 815
13. Remove the four roof retaining screws (13) located in the four corners of
the cab roof.
Fig. 816
14. Remove the cab roof (14).
Fig. 817
30-229
Method of intervention
Refitting
1. Refitting is the reverse of removal.
30.6.15 - Seat
Removal
1. Remove the four fixing screws (1).
Fig. 818
2. Remove seat (2).
Fig. 819
Refitting
1. Refitting is the reverse of removal.
30-230
Method of intervention
30.6.16 - Air conditioning system - Standard roof version
30-231
Method of intervention
l Minimum safety pressure: 2.45 bar Maximum safety pressure: 28 bars
Refrigerant type: R134a
Refrigerant quantity: 1100 g
Total quantity of moisture-free oil added at 1st charging: 200 g
Oil type: SUN-OIL COMPANY SP20
Operation
The compressor (1) is driven from the crankshaft via a drivebelt and pulley with an electromagnetic clutch (1a), which is controlled by
a switch on the control panel. The system is protected by a safety pressure switch, which performs the following functions:
l Inhibits engagement of the electromagnetic clutch (1a) when the system pressure falls below 2.45 bar as a result of incom-
plete charging or refrigerant leakage.
Disengages the clutch (1a) and thereby stops the compressor when the pressure exceeds the permitted maximum of 28 bar
(406 psi) (generally as a result of overheating).
A further contact controls the operation of fan (10) of condenser (2) in order to maintain normal operating pressure within the range
of 11 to 15 bar. The refrigerant (in vapour form) is drawn in by the compressor where it is compressed. This compression causes the
temperature of the vapour to rise; the refrigerant flows to the condenser (2) where its heat is radiated to the air flow generated by
the cooling fans (10). The refrigerant vapour is thus cooled to the point where it condenses to high-pressure liquid. On leaving the
condenser, the liquefied refrigerant flows to the receiver-drier (3) which performs three functions: to filter out any impurities, absorb
any moisture in the circuit, and finally, act as a storage reservoir. The liquid refrigerant is then transferred to the evaporator (6) through
the expansion valve (5), which meters the flow of refrigerant into the evaporator to ensure optimum evaporation. In the evaporator,
the refrigerant expands to the critical evaporation point with an ambient temperature of around -- 8C (17.6F). The temperature of
the air flow over the evaporator (6) generated by the fans (8) is significantly higher than -- 8C (17.6F), and therefore it gives up its
heat to the refrigerant, causing it to boil and evaporate. On leaving evaporator (6), the refrigerant returns to compressor (1) to repeat
the cycle. The removal of heat from the ambient air flowing over the evaporator causes the moisture in the air to condense, and the
air is thus dehumidified; the moisture condenses on the fins of the evaporator, where, if it is not maintained at temperature above 0C
(32F), it will freeze and impair the efficiency of the evaporator. The task of maintaining the evaporator at a temperature above 0C
(32F) (and within the optimum temperature for efficient heat exchange), is performed by an electronic temperature sensor (7); this
sensor disengages the clutch (1a) of the compressor (1) when the temperature falls to the lower limit and engages the clutch (1a)
when the evaporator temperature reaches the upper limit. The condensate that forms on the evaporator fins (6) contains dust, pollen
and other airborne particulates; continuous condensation thus has the effect of purifying the air, and the droplets of condensate are
conveyed out of the vehicle via two ducts. A fixed quantity of moisture-free oil is added to the circuit in order to lubricate all the mecha-
nical components of the system; a certain percentage of this oil continuously circulates in the form of an oil mist, thereby lubricating
the compressor (pistons and bearings) and the expansion valve.
Discharging, flushing and recharging
1. DANGER
Before discharging, flushing and recharging the air conditioning system, check the system for leaks using a
leak detector.
2. In order to carry out the system servicing operations you will require a dedicated A/C servicing station capable of performing
the following tasks:
m Aspiration of the refrigerant fluid.
m Creation of a high vacuum to purge the system of contaminants.
m Filtration of the recovered refrigerant.
m Separation of the antifreeze and lubricating oil from the liquid refrigerant and determination of its quantity by weight.
m Recharging system with the exactly the same amounts of refrigerant and oil as those recovered.
m Measuring the system high side pressure and low side pressure.
2. Connect the service machine to high pressure service valve (1) and follow the specific instructions for the service machine to
discharge the system.
3. Disconnect the system component to be renewed or overhauled immediately after the service machine stops; plug the open
ends of the system pipes as quickly as possible.
30-232
Method of intervention
Flushing and recharging the system
1. Before each recharging, the system must be purged of all air, moisture and contaminants (oxides, deposits). This entails
creating a high vacuum within the system to evaporate any moisture present. The vapour, when extracted, draws with it any
contaminants present in the system.
m For the flushing and recharging operations, the service station must be connected to the high (1) and low (2) pressure
service valves.
DANGER
Maximum vacuum must be maintained for at least 10 minutes.
2. After flushing, the moisture-free oil recovered during the discharging operation must be returned into the system, followed by
the refrigerant.
m Quantity of refrigerant (R134a): 1100 g Oil quantity: the quantity recovered.
DANGER
If the system must be discharged and flushed in order to renew a system component, the quantity of oil in the
replaced component must be measured and the same amount of new oil must added as that recovered with
the refrigerant.
DANGER
For details of the oil and refrigerant recharging procedure, refer to the instructions supplied with the service
machine.
Fig. 821
2. Undo locknut (3) and loosen the tensioner so as to remove the drivebelt.
Fig. 822
30-233
Method of intervention
3. Disconnect compressor wiring connector (4).
Fig. 823
4. Remove the screw from clamp (5) securing the front and rear pipes.
Fig. 824
5. Remove the two retaining screws in order to remove front pipe (6) and
remove the retaining screw to remove rear pipe (7).
Fig. 825
6. Remove the two upper screws (8) and the two lower screws (9), moving the
compressor away from the support bracket.
Fig. 826
30-234
Method of intervention
7. Remove compressor (10).
Fig. 827
Refitting
1. Refitting is the reverse of removal.
30.6.18 - Condenser
Removal
1. Discharge the refrigerant from the A/C system.
Disconnect the condenser from pipes (1).
Fig. 828
2. Remove the two LH and RH screws (2).
Fig. 829
3. Remove condenser (3).
Fig. 830
30-235
Method of intervention
Refitting
1. Refitting is the reverse of removal.
30.6.19 - Receiver-dryer
Removal
1. Disconnect the two pressure switch wiring connectors (1).
Fig. 831
2. Disconnect pipe (2) connected to the expansion valve.
Fig. 832
3. Remove filter bracket (3).
Fig. 833
4. Disconnect pipe (4) connected to the condenser.
Fig. 834
30-236
Method of intervention
5. Remove filter (5).
Fig. 835
Refitting
1. Refitting is the reverse of removal.
Fig. 836
2. Remove the two expansion valve pipes (2).
Fig. 837
3. Remove on both sides screws (3) securing the evaporator assembly.
Fig. 838
30-237
Method of intervention
4. Remove yellow relay (4) from its seat.
Fig. 839
5. Remove complete evaporator assembly (5).
Fig. 840
Refitting
1. Refitting is the reverse of removal.
Fig. 841
2. Disconnect fan wiring connector (2) and remove relative bracket (3).
Fig. 842
30-238
Method of intervention
3. Remove the four retaining screws and remove fan assembly (4).
Fig. 843
Refitting
Refitting is the reverse of removal.
30.6.22 - Bistable pressure switch for compressor clutch engagement/disengagement
Removal
1. m It is not necessary to drain the system as it is equipped with a spe-
cific check valve (1).
Fig. 844
2. Disconnect the two pressure switch wiring connectors (2).
Fig. 845
3. Remove pressure switch (3).
Fig. 846
30-239
Method of intervention
Refitting
Refitting is the reverse of removal.
30.6.23 - Steering wheel
Removal
1. Remove cover (1).
Fig. 847
2. Unscrew centre nut (2).
Fig. 848
3. Remove steering wheel (3).
Fig. 849
Refitting
1. Refitting is the reverse of removal.
30-240
Method of intervention
30.6.24 - Adjustment of the lift control valve levers
Position control lever
Adjustment
1. Move position control lever (1) to MAX position (2).
Fig. 850
2. Loosen nut (3).
Fig. 851
3. Adjust end fitting (4) to bring screw (5) into contact with stop (6), then tight-
en nut (3).
Fig. 852
30-241
Method of intervention
Draft control lever
Adjustment
1. Move position control lever (1) to CONTR position (7).
Fig. 853
2. Loosen nut (8) and adjust end fitting (9).
Fig. 854
3. Move draft control lever (10) to position 4 (11).
Fig. 855
4. Once the lift has been raised, tighten nut (8).
Fig. 856
Balance check
1. With position control lever (1) in the CONTR position (7) and draft control lever (10) in position 4 (11), check that the linkage
is raised when the test implement is pulled upwards and is lowered when the test implement is pulled downwards.
m Test implement: 200 kg counterweight.
30-242
Method of intervention
30.6.25 - Remote valve control levers
Removal
1. Remove control lever pin (1).
Fig. 857
2. Disconnect the two tie-rods (2) of the rear remote valve control linkage.
Fig. 858
3. Remove control levers (3).
Fig. 859
Refitting
1. Refitting is the reverse of removal.
30-243
Method of intervention
30.7 - H0 - Hydraulic system
30.7.1 - Pump for hydraulic lift and auxiliary services and power steering system
Removal
1. DANGER
Disconnect the lead from the battery negative terminal (-).
Fig. 860
3. Remove the two screws (2) the remove the pumps assembly (3).
Fig. 861
Refitting
1. Refitting is the reverse of removal.
m Renew gasket (4) after every removal.
Fig. 862
30-244
Method of intervention
30.7.2 - Transmission oil filter assembly
Removal
1. Loosen the two hose clamps (1) and collect the transmission oil.
Fig. 863
2. Remove the two screws (2) securing the oil filter.
Fig. 864
3. Disconnect the wiring connector (3) of the filter clogging sensor.
Fig. 865
4. Remove oil filter (4) together with suction pipe.
Fig. 866
30-245
Method of intervention
Refitting
Refitting is the reverse of removal.
l After refitting the filter, fill the transmission with 30 litres of oil.
2. Remove the two screws (1), remove cover (2) and disconnect the two
steering control pipes (3).
m Plug the pipes to prevent the ingress of contaminants.
Fig. 867
3. Disconnect supply pipe (4) to the power steering valve and fully loosen nut
(5) but do not remove it.
Fig. 868
4. Remove screw (6) to release pipe (7) from the controls support and discon-
nect return pipe (8).
Fig. 869
5. Undo the two unions (9).
m Renew the copper washers on reassembly.
Fig. 870
30-246
Method of intervention
6. Remove the four screws (10), remove steering tube (11) and remove the
power steering valve (12).
Fig. 871
Refitting
1. Refitting is the reverse of removal.
m After refitting all the components, start the engine and bleed the air from the steering circuit.
30-247
Method of intervention
30.7.4 - Power steering disassembly
26 15
24 18 13
25
25b
27 25a
28 19
29 21
20
22
16
17a
17b
12
10
17
23a
23b
23 23a
8 5a
7 6
11
9
2
5 1
30-248
Method of intervention
Disassembly
1. Unscrew and remove screws (1) and (3) and washers (2) securing cover (4)
(6 screws plus one special screw). 3
1 2
F0009470
Fig. 873
2. Remove cover (4) by sliding it off sideways.
4
F0009480
Fig. 874
3. Lift rotary spool unit (5) complete with O-rings (6) and spacer (7).
5
6 7
F0009490
Fig. 875
4. Remove drive shaft (8).
F0009500
Fig. 876
5. Remove distributor plate (9).
F0009510
Fig. 877
30-249
Method of intervention
6. Remove relief valve stop bush (10).
10
F0009520
Fig. 878
7. Remove O-ring (11).
11
F0009530
Fig. 879
8. Remove ball (12) of the check valve and pins (13) and balls (15) of the
suction valves.
15
12 13
F0009541
Fig. 880
9. Checking through the central hole of the spool, position spool-bush as-
sembly cross pin (16) horizontally. Push assembly (17) and the bearing
assembly out of power steering housing (18).
17
18
F0009550
Fig. 881
10. Remove outer ring (19), inner ring (20) and roller bearing (21) from the
spool; remove also ring (22).
m It may occur that inner ring (20) (thin) remains in the steering valve
22 20
housing; ensure that it is actually removed.
21
19
F0009560
Fig. 882
30-250
Method of intervention
11. Remove cross pin (16), bush (17b) and spool (17a).
m Use special cover screw (3).
17b
3 16
17a
F0009570
Fig. 883
12. Slowly withdraw spool (17a) from bush (17b).
17b
17a
F0009580
Fig. 884
13. Press neutral position springs (23) and remove them from spool (17a).
23
17a
F0009590
Fig. 885
14. Remove dust seal (24) and composite seal (25) (O-ring + seal).
25
24
F0129940
Fig. 886
15. Remove plug (26) and its seal.
26
F0129930
Fig. 887
30-251
Method of intervention
16. Remove pressure relief adjuster screw (27).
27
F0129950
Fig. 888
17. Turn over the steering valve housing and remove spring (28) and relief
valve (29).
IMPORTANT 29
The seat of the relief valve is a force fit in the housing and
28
cannot be removed.
F0009681
Fig. 889
Installation
1. IMPORTANT
Prior to reassembly, lubricate all components with gearbox
23b
oil. 23a
Insert the two flat washers (23a) in the seat and centre them relative to
the diameter of spool (17a). Insert the four curved washers (23b) in pairs
23b 23a 17a
between the two flat washers (23a) and push them fully home.
F0009690
Fig. 890
2. Align spring assembly (23).
23
F0009700
Fig. 891
3. Insert spool (17a) in bush (17b).
IMPORTANT 17b
Check that the position between the bush and the spool is 17a
as described in stage 1.
F0009580
Fig. 891
30-252
Method of intervention
4. Simultaneously push springs (23) and spool (17a) until the springs are
seated in the slots in bush (17b). 23
17a
17b
F0009710
Fig. 892
5. Align springs (23) and make sure they are positioned centrally in relation to
the diameter of bush (17b). 23
17b
F0009720
Fig. 893
6. Install ring (22) on its seat on bush (17b).
IMPORTANT
22
Ring (22) must be free to rotate without interfering with
springs (23).
17b
F0009730
Fig. 894
7. Insert cross pin (16).
16
F0009740
Fig. 895
8. Install the thrust bearing components in the order indicated in point 9.
20
22 21 F0009751
Fig. 896
30-253
Method of intervention
9. Thrust bearing assembly.
20
m 17a - Spool
17b - Bush 21
21- Needle roller bearing 22
20 - Inner ring
22 - Outer ring
17
DANGER
17
The outer ring must be installed with chamfer X facing the
shoulder of the spool.
Fig. 897
10. Position steering valve housing (18) so the hole is horizontal. Insert into the
bush/spool assembly bore the guide of special tool T9 (P/N. 5.9030.480.0).
Fig. 898
11. Lubricate oil seal (25a) and O-ring (25b) and fit them on the push rod of tool
T9 (P/N. 5.9030.480.0).
Fig. 899
12. Fit tool T9 (P/N. 5.9030.480.0). and insert it in the guide previously inserted
in the steering valve bore.
Fig. 899
13. Push seal (25) into its seat in steering valve housing (18) while rotating it
to ease it into position.
18
F0009790
Fig. 900
30-254
Method of intervention
14. Withdraw tool T9 (P/N 5.9030.480.0). from valve housing (18) and removal
also the guide, leaving the tool push rod in the housing.
Fig. 901
15. Insert bush/spool assembly (17) in steering valve bore (18). Rotate the
valve slightly while inserting it to ease it into position.
17
IMPORTANT
Keep the cross pin horizontal while inserting the assembly.
18
F0009810
Fig. 902
16. Push in assembly (17) until fully seated so that it forces out the tool push
rod left in the housing in step 14. 18
17
F0009820
Fig. 903
17. Rotate steering valve housing (18) until the centre hole is vertical. Insert
ball (12) of the relief valve in the hole indicated by the arrow. 12
18
F0009830
Fig. 904
18. Screw valve retaining bush (10) into the bore of the relief valve.
IMPORTANT
10
The top of the retaining bush should be set below the face of
steering valve housing (18).
18
F0009521
Fig. 905
30-255
Method of intervention
19. Insert the two balls (15) in the holes indicated by the arrows.
15
F0010310
Fig. 906
20. Insert elements (13) in the same holes.
13
F0009841
Fig. 907
21. Lubricate O-ring (11) and fit it in its seat.
11
m O-ring: Gearbox oil
F0009850
Fig. 908
22. Locate distributor plate (9) so that its holes are aligned with the holes in
9
steering valve housing (18).
18
F0009860
Fig. 909
23. Insert drive shaft (8) in the hole so that it engages the cross pin; check
that the engagement with the cross pin is parallel to the steering column
mounting face.
8
F0009870
Fig. 910
30-256
Method of intervention
24. Position the drive shaft so that it is vertical and hold it in this position using
a suitable tool.
F0009880
Fig. 911
25. Lubricate the two O-rings (6) and fit them in the two grooves in rotary spool
unit (5). Fit rotary spool unit (5) to drive shaft (8). 6
F0009890
Fig. 912
26. DANGER
Install rotor (5a) on drive shaft (8) so that the valley between
two lobes is aligned with the groove in the end of the drive
shaft. Then turn outer ring (5b) to align the fixing holes. 8
5a
F0009900
Fig. 913
27. Install spacer (7).
7
F0009910
Fig. 914
28. Fit cover (4).
4
F0009920
Fig. 915
30-257
Method of intervention
29. Insert special screw (3) complete with washer (2) in the hole indicated in
the photo.
3
F0009930
Fig. 916
30. Insert the six screws (1) complete with washers (2). Tighten screws (1) and
(3) in a crosswise sequence to a torque of 306 Nm (22.14.4 lb.ft.). 3
1 2
F0009471
Fig. 917
31. Fit valve (29).
29
F0129960
Fig. 918
32. Fit spring (28).
28
F0129970
Fig. 919
33. Fit pressure adjustment screw (27).
27
F0129950
Fig. 919
30-258
Method of intervention
34. Fit plug (26) complete with seal.
m Plug: 5010 Nm (36.87.4 lb.ft.)
26
F0129930
Fig. 919
35. Locate dust seal (24) in steering valve housing (18).
24
18
F0009970
Fig. 920
36. Install dust seal (24) in the steering valve housing using a suitable drift and
a soft faced mallet.
F0009980
Fig. 921
37. Close off the oil ports with plastic plugs to prevent impurities getting in.
IMPORTANT
Fit the plugs by hand pressure alone; do not hammer.
F0009990
Fig. 922
38. On completion of the assembly operation, test the operating pressure of the relief valve and calibrate as necessary.
30-259
Method of intervention
30.7.5 - Pressure relief valve - lift control valve
Removal
1. Unscrew plug (1).
Fig. 923
2. Withdraw spring (2), gasket and washer (3).
Fig. 924
3. Withdraw pressure relief valve (4) and spool (5).
Fig. 925
Refitting
1. Refitting is the reverse of removal.
m Renew the gasket on reassembly
Fig. 926
30-260
Method of intervention
Calibration
1. Interpose one or more shims (6) between the spring and the plug to in-
crease the spring preload and thereby return the operating pressure in the
circuit to 30 bar.
Fig. 927
Fig. 928
2. Remove valve (2).
Fig. 929
Refitting
1. Refitting is the reverse of removal.
m Renew copper gasket (3) on reassembly.
Fig. 930
30-261
Method of intervention
30.7.7 - Remote control valve
Removal
1. Undo the two unions (1) and remove pipe (2).
m Renew the washers on reassembly
Fig. 931
2. Remove the four screws (3) and remove remote control valve assembly (4).
m Check the condition of the O-rings and renew them if necessary.
Fig. 932
Refitting
1. Refitting is the reverse of removal.
m Holes for remote control valve retaining screws: Loctite 510.
m O-rings: apply grease to hold them in position.
Fig. 933
Fig. 934
30-262
Method of intervention
2. Remove screws (2) and remove plate (3).
Fig. 935
3. Remove the spool of control valve n 1 (4) and the spool of control valve
n 2 (5).
Fig. 936
4. Remove plug (6) and remove the spring and ball (7).
Fig. 937
5. Remove screw (8) and disassemble the spool return device.
Fig. 938
6. Remove screw (9) then remove disc (10), spring (11) and disc (12).
Fig. 939
30-263
Method of intervention
Assembly
1. To assemble, follow the disassembly steps in reverse order.
Fig. 940
2. Remove the two Woodruff keys (4), then remove Woodruff key (5), ring (6)
and O-ring (7).
Fig. 941
3. Withdraw the two rods (8) and (9) then remove O-ring (10).
Fig. 942
Assembly
1. To assemble, follow the disassembly steps in reverse order.
m Grease the rods and the O-rings.
30-264
Method of intervention
30.7.10 - Double/single acting conversion valve
Removal
1. Remove complete valve (1).
m Renew the copper washers on reassembly.
Fig. 943
2. Remove ball (2) using a magnet and remove spring (3).
Fig. 944
3. Remove circlip (4) and separate nut (5) from pin (1).
Fig. 945
4. Remove O-ring (6).
m Renew O-ring (6) on reassembly.
Fig. 946
30-265
Method of intervention
Refitting
1. Refitting is the reverse of removal.
Fig. 947
30-266
Method of intervention
30.8 - L0 - Electrical system
30.8.1 - Battery
Removal
1. DANGER
Disconnect the lead from the battery negative terminal (-).
Fig. 948
3. Remove battery holder (2).
Fig. 949
4. Detach fan control unit (3) an move it out of the way of the battery.
Fig. 950
5. Remove positive terminal cover (4) and loosen clamp screw (5) securing
positive lead (6).
Fig. 951
30-267
Method of intervention
6. Remove battery (7) raising the front and withdrawing it a forward direction.
Fig. 952
Refitting
Refitting is the reverse of removal.
30.8.2 - Fuse and relay assembly
Removal
1. Remove on both sides the retaining screws (two per cover) and side cov-
ers (1).
Fig. 953
2. Remove the six retaining screws and remove upper panel (2).
Fig. 954
3. Remove the six retaining screws and remove cab roof lining (3) from the
rear of the cab.
Fig. 955
30-268
Method of intervention
4. Remove the three screws and remove fuse unit support (4).
Fig. 956
5. Remove the two screws (5) and remove relay support bracket (6).
Fig. 957
Refitting
1. Refitting is the reverse of removal.
Fig. 958
2. Remove the three retaining screws (2).
Fig. 959
30-269
Method of intervention
3. Disconnect wiring connector (3).
Fig. 960
4. Remove electrostatic unit (4).
Fig. 961
Refitting
1. Refitting is the reverse of removal.
Fig. 962
2. Remove the two retaining screws (3).
Fig. 963
30-270
Method of intervention
3. Disconnect wiring connector (4).
Fig. 964
4. Remove switch (5).
Fig. 965
Refitting
1. Refitting is the reverse of removal.
Fig. 966
30-271
Method of intervention
30.8.6 - Brake lights switches
Removal
1. Remove the two screws securing the switch (1).
Fig. 967
2. Disconnect wiring connector (2).
Fig. 968
3. Remove switch (3).
Fig. 969
30-272
Method of intervention
Refitting
1. Refitting is the reverse of removal.
Fig. 970
Fig. 971
2. Remove steering column switch unit (2).
Fig. 972
Refitting
1. Refitting is the reverse of removal.
30-273
Method of intervention
Removal
1. Remove the two rear lift control knobs (1) and the two remote valve control
knobs (2).
Fig. 973
2. Remove the three retaining screws (3) under the RH fender.
Fig. 974
3. Remove the two internal screws (4) securing the console.
Fig. 975
4. Move the console aside and disconnect front PTO wiring connector (5).
Fig. 976
30-274
Method of intervention
5. Remove console (6).
Fig. 977
Refitting
1. Refitting is the reverse of removal.
30-275
Method of intervention
30.9 - M0 - Front PTO
30.9.1 - Pump - clutch assembly - brake
Removal
1. Remove the eight fixing screws (1) of the upper cover of the front PTO.
Fig. 978
2. Remove cover (2).
m Check the condition of the gasket (3) inside the cover.
Fig. 979
3. Loosen the plug on the underside of the sump (4) to allow the oil to drain
out of the PTO.
Fig. 980
4. Remove side plug (5).
m Recover the washer and seal (6).
Fig. 981
30-276
Method of intervention
5. Remove oil filter (7).
Fig. 982
6. Remove the three retaining screws (8) of the front bearing cover.
Fig. 983
7. Remove cover (9).
m Recover the O-ring.
Fig. 984
8. Remove the three retaining screws (10) of the oil pump.
Fig. 985
30-277
Method of intervention
9. Remove flange (11) connecting the shaft to the crankshaft pulley.
Fig. 986
10. Remove shaft (12) from the front end.
Fig. 987
11. Remove the second PTO drive shaft (13) from the front end .
Fig. 988
12. Remove the clutch-brake and oil transfer pump assembly (14).
m Recover bearing (15).
Fig. 989
30-278
Method of intervention
Refitting
1. Refitting is the reverse of removal.
Fig. 990
2. Remove the three retaining screws (2) of the PTO input shaft flange.
Fig. 991
3. Remove the two hydraulic hose clamps (3).
Fig. 992
4. Remove the two lower screws (4) and four front screws (5) of the front lift
support.
Fig. 993
30-279
Method of intervention
5. Remove front lift support (6).
Fig. 994
6. Remove PTO oil sump (7).
Fig. 995
7. Remove oil seal (8).
m To remove the oil seal, make a hole in it and use a slide hammer
puller.
Fig. 996
8. Remove circlip (9).
Fig. 997
30-280
Method of intervention
9. Remove PTO output shaft (10) with gear (11) and bearing (12).
Fig. 998
Refitting
1. Refitting is the reverse of removal.
Fig. 999
2. Remove solenoid retaining nut (2).
m Make a note of the correct installation sequence of the solenoids
and the four O-rings.
Fig. 1000
3. Remove nut (3).
Fig. 1001
30-281
Method of intervention
4. Withdraw solenoid valve (4).
m Check the condition of the mesh filter (5) on the solenoid valve.
Fig. 1002
Refitting
1. Refitting is the reverse of removal.
30-282
Method of intervention
30.10 - N0 - Front lift
30.10.1 - Front lift - version with front PTO -
Removal
1. Remove the two cotter pins (1) and the two relative pivot pins (2).
Fig. 1003
2. Remove the two front lift arms (3).
Fig. 1004
3. Remove the two hydraulic service couplers (4) with their copper washers
and circlips (5).
m Renew the copper washers on reassembly.
Fig. 1005
4. Disconnect cylinder supply pipe (6).
m Renew the copper washer on reassembly.
Fig. 1006
30-283
Method of intervention
5. Remove on both sides the two screws (7) securing the front lift assembly on
the underside of the support.
Fig. 1007
6. Remove the four screws (8) securing the front part of the front lift assembly.
Fig. 1008
7. Remove front lift assembly (9).
Fig. 1009
30-284
Method of intervention
Refitting
1. Refitting is the reverse of removal.
30.10.2 - Cylinder
Removal
1. Remove split pin (1).
Fig. 1010
2. Remove cylinder retaining pin (2).
Fig. 1011
3. Remove circlip (3).
Fig. 1012
4. Remove pin (4) and cylinder (5).
Fig. 1013
30-285
Method of intervention
Refitting
1. Refitting is the reverse of removal.
30-286
Method of intervention
30.11 - R0 - Rear lift
30.11.1 - Rear lift - complete assembly
Removal
1. Disconnect front lift supply pipes (1).
Fig. 1014
2. Disconnect the four pipes (2) of the rear hydraulic service couplers.
Fig. 1015
3. Remove the two pipe retaining brackets (3).
Fig. 1016
4. Remove the two centre screws (4) and remove service coupler support
frame (5).
Fig. 1017
30-287
Method of intervention
5. Remove screw (6) securing the holding valve to the lift cover.
Fig. 1018
6. Remove the two locking pins (7) and two pivot pins (8) from the link arms.
Fig. 1019
7. Remove the nine screws (9) securing the lift assembly to the transmission.
Fig. 1020
8. Remove complete lift assembly (10).
Fig. 1021
30-288
Method of intervention
Refitting
1. Refitting is the reverse of removal.
m Fixing screws (9): 40 2 Nm.
Fig. 1022
2. Turn the lift assembly over, remove the three screws (3) and loosen screw
(4).
Fig. 1023
3. Turn the lift assembly over again, remove the screw (4) previously left in
place and remove cylinder assembly (5).
Fig. 1024
Refitting
1. Refitting is the reverse of removal.
m Cylinder fixing holes: Loctite 510.
Fig. 1025
30-289
Method of intervention
Lift cylinders
Disassembly
1. Remove lift safety valve (6).
m Renew the copper washers on reassembly.
Fig. 1026
2. Using a bar made of soft material, withdraw piston (7) from cylinder (5).
Fig. 1027
3. Remove seal (8) from piston (7).
m Note which way round seal (8) is installed.
Fig. 1028
Assembly
1. To assemble, follow the disassembly steps in reverse order.
m Check that seal (8) is the right way round.
m Seal and cylinder: transmission oil.
Fig. 1029
30-290
Method of intervention
Lift arms
Removal
1. Detach springs (9) from levers (10).
Fig. 1030
2. Remove cotter pin (11) and remove pivot pin (12).
m Always renew the cotter pin on reassembly.
Fig. 1031
3. On both sides, remove circlip (13), remove lift arm (14) and then remove
thrust washer (15).
Fig. 1032
4. Loosen nut (16) and remove set screw (17).
m Note the position of cam (18).
Fig. 1033
5. Loosen nut (19) and remove set screw (20).
Fig. 1034
30-291
Method of intervention
6. Withdraw shaft (21) towards the side opposite controls (22).
m Renew the oil seal on the opposite side to the controls on reas-
sembly.
m Note which way round the oil seal is installed.
m Note that the widest part of plate (23) faces upwards.
Fig. 1035
7. Remove oil seal (24) from the controls side.
m Note which way round the oil seal is installed.
Fig. 1036
8. Check that bushes (25) are not worn out-of-round and renew them if neces-
sary.
Fig. 1037
30-292
Method of intervention
Refitting
1. Refitting is the reverse of removal.
m Check that all components are installed the right way round.
2. Screw in fully and then, while holding it in position, secure with the nut.
m Grub screw: Loctite 242
3. Screw fully into its seating on the shaft and then unscrew it by half a turn. Hold in position and secure with the nut.
m Grub screw: Loctite 242
Bush
Renewal
1. Position the lift cover under a press and, using a suitable tool, remove bush
(26).
Fig. 1038
2. Fit the new bush (26) in the lift cover, taking care to align it with the hole
Fig. 1039
3. Fit the bush with the split rotated 45 relative to the rear of the lift cover
Fig. 1040
30-293
Method of intervention
30.11.3 - Adjustment of the rear lift
Internal adjustment
Safety stop
1. Move cylinder (1) to bring lever (2) up to stop (3).
Fig. 1041
2. Adjust screw (4) to obtain a clearance of 2 0.5 mm (5).
Fig. 1042
3. Tighten nut (6).
m Screw (A): Loctite 242.
Fig. 1043
30-294
Method of intervention
External adjustment
Maximum lift height
1. Move position control lever (7) to MAX position (8).
Fig. 1044
2. Move draft control lever (9) to position 12 (10).
Fig. 1045
3. Move RH lever (11) to bring the notch on the lever into alignment (12) with
the notch on the hub of the casing (13).
Fig. 1046
4. Adjust screw (14) to bring it up against stop (15) then tighten nut (16).
Fig. 1047
30-295
Method of intervention
Adjustment of the sensor tie-rod
Adjustment
1. Install the various components of the sensor tie-rod as shown in the figure.
Fig. 1048
2. Adjust the length (17) to 92.4 0.2 mm.
Fig. 1049
Fig. 1050
2. Turn the lift assembly over, remove the three screws (3) and loosen screw
(4).
Fig. 1051
30-296
Method of intervention
3. Turn the lift assembly over again, remove the screw (4) previously left in
place and remove cylinder assembly (5).
Fig. 1052
Refitting
1. Refitting is the reverse of removal.
m Cylinder fixing holes: Loctite 510.
Fig. 1053
Fig. 1054
2. Using a bar made of soft material, drive piston (3) out from cylinder (2).
Fig. 1055
30-297
Method of intervention
3. Remove seal (4) from piston (3).
m Note which way round seal (4) is installed.
Fig. 1056
Assembly
1. To assemble, follow the disassembly steps in reverse order.
m Check that seal (4) is installed the right way round.
m Seal and cylinder: transmission oil.
Fig. 1057
Fig. 1058
2. Install new bush (1) making sure that it is inserted flush with the bore in the
lift cover.
Fig. 1059
30-298
Method of intervention
3. Fit the bush with the split rotated 45 relative to the rear (A) of the lift cover.
Fig. 1060
Fig. 1061
2. Remove cotter pin (3) and remove pivot pin (4).
m Always renew the cotter pin on reassembly.
Fig. 1062
3. On both sides, remove circlip (5), remove lift arm (6) and then remove
thrust washer (7).
Fig. 1063
30-299
Method of intervention
4. Loosen nut (8) and remove set screw (9).
m Note the position of cam (10).
Fig. 1064
5. Loosen nut (11) and remove set screw (12).
Fig. 1065
6. Withdraw shaft (13) towards the side opposite controls (14).
m Renew the oil seal on the opposite side to the controls on reas-
sembly.
m Note which way round the oil seal is installed.
m Note that the widest part of plate (15) faces upwards.
Fig. 1066
7. Remove oil seal (16) from the controls side.
m Note which way round the oil seal is installed.
Fig. 1067
8. Check that the bushes (17) are not worn out-of-round and renew them if
necessary.
Fig. 1068
30-300
Method of intervention
Refitting
1. Refitting is the reverse of removal.
m Check that all components are installed the right way round.
2. Screw in fully and then, while holding it in position, secure with the nut.
m Grub screw: Loctite 242
3. Screw fully into its seating on the shaft and then unscrew it by half a turn. Hold in position and secure with the nut.
m Grub screw: Loctite 242
Fig. 1069
3. Undo the two unions (3) and remove pipe (4).
Fig. 1070
4. Detach springs (5) from levers (6).
Fig. 1071
30-301
Method of intervention
5. Remove cotter pin (7) and remove pivot pin (8).
m Renew the cotter pin on reassembly.
Fig. 1072
6. Remove screws (9) and remove control valve (10).
Fig. 1073
Refitting
1. Refitting is the reverse of removal.
m For control valve fixing screw holes: Use Loctite 510.
m Hydraulic travel limit control lever: Check adjustment.
Fig. 1074
Fig. 1075
30-302
Method of intervention
2. Remove screw (3) and separate control valve bodies (4) and (5).
Fig. 1076
3. Remove spring (6) and spacer (7) from valve body (4).
Fig. 1077
4. Remove circlip (8), washer (9) and spring (10).
m Gradually relieve the load exerted by spring (10).
Fig. 1078
5. Withdraw valve (11).
Fig. 1079
6. Remove plug (12) and remove valve (13), pin (14) and spring (15).
m Renew the copper washers on reassembly.
Fig. 1080
30-303
Method of intervention
7. Withdraw piston (16) from the valve body (4).
Fig. 1081
8. Remove the four O-rings (17) from valve body (4).
Fig. 1082
9. Withdraw spool (18) from valve body (5) and remove piston (19) and spring
(20).
Fig. 1083
10. Remove plug (21) and withdraw spring (22), spacer (23) and valve (24).
m Renew the copper washers on reassembly.
Fig. 1084
11. Remove spring (25) and rod (26).
Fig. 1085
30-304
Method of intervention
12. Remove plug (27) and remove spring (28) and valve (29).
m Renew the copper washers on reassembly.
Fig. 1086
13. Remove valve (30).
m Renew the copper washers on reassembly.
Fig. 1087
Assembly
1. Assemble by reversing the disassembly sequence.
2. Check that valve (13) is installed the right way round.
Check that valve (13) slides freely in its seat.
Fig. 1088
3. Check that piston (16) is installed the right way round.
Fig. 1089
30-305
Method of intervention
4. Check that spool (18) slides freely without sticking.
Check that piston (19) slides freely in its seat.
Fig. 1090
5. Check that valve (24) slides freely.
Make sure that the assembly sequence is correct.
Fig. 1091
6. Check that rod (26) is installed the right way round.
Fig. 1092
7. While holding ball (A) in valve (29) tight up against rod (26), that the stand-
out of rod (26) relative to the face of valve body (5) is within the prescribed
tolerance limits: 15.8 0.05 mm (B).
Fig. 1093
30-306
Method of intervention
30.11.10 - Three-point linkage with mechanical adjustment
Removal
1. Remove the two screws (1) and remove rear PTO output shaft shield (2).
Fig. 1094
2. Remove the two pins (3) and towing hitch support pins (4).
Fig. 1095
3. Remove rear towing hitch (5).
Fig. 1096
4. Remove the six screws (6) and remove the two brackets (7) for lateral ad-
justment of the towing hitch.
Fig. 1097
30-307
Method of intervention
Refitting
1. Refitting is the reverse of removal.
30-308
Method of intervention
30.12 - S0 - Wheels
30.12.1 - Front wheels
Removal
1. DANGER
Remove the key from the starter switch and apply the parking brake.
2. Raise the tractor and position two stands A under the front axle.
Remove all the screws (1) except one, which should be left in position for
safety.
Remove the wheel. Repeat the above operations for the other wheel.
Fig. 1098
Refitting
1. Refitting is the reverse of removal.
m Wheel screws: 169 Nm (124.5 lb.ft.)
Fig. 1099
2. Position a stand B under the rear axle housing and lower the jack until the
axle housing is resting on the stand.
Check that the stand is in exactly the correct position and then remove the
trolley jack.
Repeat the above operations to remove the other wheel.
Fig. 1100
Refitting
1. Refitting is the reverse of removal.
m Nuts: 169 Nm (124.5 lb.ft.)
30-309
Method of intervention
30.13 - V0 - Ballast - towing hitches
30.13.1 - Support and towing hitch
Removal
1. Remove the two locking pins (1).
Fig. 1101
2. Remove the two pins (2).
Fig. 1102
3. Removing towing hitch support and guard (3).
Fig. 1103
Refitting
1. Refitting is the reverse of removal.
30-310
40 - Wiring diagrams
40-1
Wiring diagrams
40.1 - Introduction
40.1.1 - Structure of the unit
For easier consultation, this unit has been divided into the following chapters:
l introduction
m Contains a brief description of the terminology used, the procedures to follow for troubleshooting and repairs, and the
l Components
m Contains the layouts of the connectors used in the electrical system, descriptions of the components installed on the
tractor,the technical data necessary for functional testing and the pinouts of the electronic control units.
l Systems
m Contains the electrical diagrams of the tractors systems.
l Wiring looms
m Contains the layouts, the wiring diagrams and the positioning of connectors on the tractor.
Fig. 1104
How to consult the table
The quickest way to determine the cause of a malfunction of a component (e.g. the starter motor) is to check all the components in
the system in which the component is incorporated. In this example, the problem is a malfunction of the starter motor, which fails to
start the engine.
l Find the starter motor in heading Index by part description and identify the system in which the component is incorporated.
The system is indicated in the System column and in this case is 2 (figure A).
40-2
Wiring diagrams
l Consult heading Starting (figure B), where all system components are shown in the electrical diagram; these components
are accompanied by numbers that correspond to the key on the same page.
l Check all the components in the system, starting for example with switch 1.
l In heading Index by part description (figure A) find the item Start switch and check in the column Technical Descrn to see
if there is a technical description of the component (in this case it appears at no. 42 in the heading component technical data)
(figure C). Take note also of the name of the connector to which the component is connected (in this case X4).
Only if the position of the component is not known
Only if the position of the component is not known:
l In heading Connector index (figure D) find the name of the connector to which the component is connected (in this case
X4) and note down the wiring loom in which it is incorporated (in this case 0.012.5957.4) and the type of connector (in this
case 19).
l Find the wiring loom in chapter Plans, wiring diagrams, connector positions using the index at the beginning of the chapter.
l Find the name of the connector in the photos attached to the electrical diagrams and establish its position on the tractor using
the drawing (figure E)
l Using the data contained in the paragraph Component technical data (figure C) in position no. 42, check the operation of
the switch.
DANGER
In the electrical diagrams (figure F) are indicated the names of the connectors and the descriptions that are used in
all the tables of chapter 2.
DANGER
If the pinout of the connector is not known, look in paragraph Connector layouts (figure G) for the number found in
the column Type of paragraph Connector index.
introduction
This section of the workshop manual is intended as a practical guide to troubleshooting the tractors electrical and electronic systems.
The following pages provide the technician with all the necessary information regarding the tractors systems and components. Due
to the possible time difference between the introduction of technical modifications (in line with our policy of continuous product im-
provement) and the corresponding amendment of our printed documentation, we are obliged to state that the data contained in this
document are subject to modification and as such are not binding.
Definition of components and symbols
To prevent any misunderstanding or ambiguity, listed below are definitions for some of the key terms used in this unit.
Table 100
TERM DESCRIPTION
Connector Element used to connect two components (e.g. wiring-switch, wiring-wiring)
Transmission oil Electrical component that converts the temperature of a medium (air, water, oil, etc.) into a voltage
or resistance
Main clutch Electrical component that converts the pressure of a medium (air, water, etc.) into a voltage or
resistance
Accelerator pedal Electrical component that converts the angular or linear position of an object into a voltage
Pressure switch Switch that changes state (opens or closes a contact) according to the operating pressure in the
circuit in which it is installed
Thermostat Switch that changes state (opens or closes a contact) according to the temperature of the medium
in which it is immersed.
Lights switch Mechanical component that opens or closes one or more electrical contacts.
HML control Valve operated by applying electrical current to a coil (or solenoid)
Chapter Components shows the wiring diagrams for certain switches and buttons. The following symbols are used for ease of
interpretation:
Table 101
SYMBOL DESCRIPTION
Contact between pins CLOSED (stable switch position)
40-3
Wiring diagrams
SYMBOL DESCRIPTION
Contact between pins CLOSED (unstable switch position)
Indicator LED
Indicator lamp
Diode
General rules
The inspection, maintenance, troubleshooting and repair operations are essential to ensure that the tractor continues to operate
correctly over time and to prevent malfunctions and breakdowns. The scope of this paragraph is to describe repair procedures and
to help improve the quality of repairs.
Modification of the tractors electrical/electronic circuits
The manufacturer prohibits any modification or alteration of the electrical wiring for the connection of any non-approved electrical
applicances or components. In particular, if it is discovered that the electrical system or a component has been modified without au-
thorisation, the Manufacturer will accept no liability for any damage to the vehicle and the vehicle warranty will be invalidated.
Main wiring faults
Bad contact between connectors
l The main causes of poor contact between connectors are incorrect insertion of the male into the female connector, deforma-
tion of one or both connectiors, and corrosion or oxidisation of the pin contact surfaces.
Defective pin soldering or crimping
l The pins of the male and female connectors make good contact in the crimped or soldered area, but the wires are subjected
to excessive tension, leading to breakage of the insulation or the wire itself and a poor connection.
Disconnecting wiring
l If components are disconnected by pulling on the wires, or if components are removed with the wires still connected, or if the
wiring is subject to a heavy impact this could damage the connections at the pins, breaking strands of wire.
Penetration of water inside connectors
l The connectors are designed to prevent penetration of liquids (water, oil etc.); however, it is possible that when the tractor is
cleaned using high-pressure water or steam, water could penetrate or condense in the connectors. As the connectors
are designed to prevent liquid penetration, any water that does get in will not be able to drain out, and thus may cause short-
circuits across the pins. For this reason it is good practice to dry the connectors with a low pressure jet of compressed air after
washing the tractor.
Oil or dirt on connectors
l If the connectors or pin contact surfaces show signs of oil or grease contamination, this will prevent the passage of current
(oil and grease are electrical insulators) creating a poor contact. Clean the connectors thoroughly using a dry cloth or a low
pressure jet of compressed air and use specific products (deoxidising sprays, etc.) to degrease the contacts.
Important
Take care not to bend the pins when cleaning them. Use dry oil-free compressed air.
40-4
Wiring diagrams
clip then pull the connector apart. After disconnecting connectors, seal them in waterproof material to prevent contamination of the
contacts with dirt or moisture.
Connecting the connectors. Check the condition of the connectors:
l Make sure the pin contact surfaces are free of water, dirt or oil.
l Check that the connectors are not deformed and that the pins are not corroded or oxidised.
l Check that the connector casings are not damaged or split.
l If a connector is contaminated with oil or grease, or if moisture has penetrated the casing, clean it thoroughly.
l If a connector is damaged, deformed or broken, replace it with a new one.
When connecting connectors, make sure they are properly aligned before applying force. For connectors with clips, insert the two
halves until they clip together.
Cleaning and drying wiring
l When wiring is dirty or contaminated with oil or grease, clean it with a dry cloth, or, if necessary, with water or steam. If the
wiring must be cleaned with water, avoid directing the water or steam jet on the connectors; if water penetrates the connector,
clean it thoroughly.
l Check that the connector is not short circuited due to the presence of water by testing for continuity across the pins.
l After checking that the connector is good condition, degrease the contacts using a deoxidising product.
Renewal of damaged electrical components.
l When replacing electrical components (fuses, relays, etc.), use only original parts supplied by the manufacturer.
l When replacing fuses, check that the new fuse conforms to DIN 72581 or ISO 8820 standards and in particular:
m fuse F1 (100A) DIN 72581/2
m bayonet fuse (F2, F3, etc.) DIN 72581/3C
m fuse F51 (100A) and F52 (200A) ISO 8820.
l The fitting of replacement fuses that do not comply with these standards will invalidate the warranty with immediate effect and
release the manufacturer from any liability.
l When replacing relays, make sure that the new relay conforms to the standards marked on the original relay.
Diagnostic instruments
For the correct diagnosis of any faults in the tractors electrical system, the following instruments are required:
l Digital multimeter with the following minimum characteristics:
m AC VOLT 0-600
m DC VOLT 0-600
m OHM 0-32M
m AC AMP 0-10
m DC AMP 0-10
40-5
Wiring diagrams
40.1.2 - Wiring and components index
List of wiring harnesses
Table 103
Description Code Wiring diagram Connector posi-
tions
Aereo cab 0.014.7593.4 40-89 40-90
Front 0.012.6951.4 40-57 40-58
Front with cab 0.015.0032.4 40-66 40-68
Cab power supply 0.014.7594.4 40-92 40-93
Compressor wiring 0.014.7601.4 40-65 40-65
Remote valve wiring 0.012.6955.4 40-86 -
Solenoid valve wiring 0.014.1482.4 40-80 40-81
Rear lights wiring 0.014.7602.4 40-86 40-87
Flashing light wiring 0.014.7597.4 40-100 40-101
Cab earth wiring 0.015.0031.4 40-96 40-96
Radio wiring 0.014.7600.4 40-104 40-104
Central wiring 0.012.6949.4 40-71 40-74
Front lights .014.7599.4 40-62 40-63
Rear 0.013.1452.4/10 40-82 40-84
Index by part description
Table 104
Component description Component code Connector System
Check panel 2.8339.230.0 A18 40-71
2.8339.230.40 A20 40-71
Sol. valve control unit 2.8519.035.4 U1 40-80
Steering column switch 0.013.3337.3 A25 40-71
Ex rotating beacon wire 0.013.9053.2 N1 40-100
RH light 2.8039.293.0 P2 40-62
2.8039.293.0 P3 40-62
LH light 2.8039.294.0 P5 40-62
P6 40-62
Front lights 2.8039.230.0 Z5 40-66
Z8 40-66
Worklights d. 80 2.8039.001.0 G14 40-89
Rear lights 2.8059.230.0 (LH) S2 40-86
S3 40-86
S4 40-86
2.8059.240.0 (RH) S6 40-86
S7 40-86
S8 40-86
Receiver-dryer 0.008.9604.0 M3 40-94
M4 40-94
Flasher 0.009.6758.4/10 A26 40-71
Bosch emergency pushbutton 2.7659.110.0 A7 40-71
PTO switch 2.7659.262.0 V4 40-61
Windscreen wiper timer relay 2.8639.008.0 G9 40-89
Windscreen wiper 2.9019.200.0 G19 40-89
Rear wiper 2.9019.190.0 L4 40-98
Air conditioning fan 0.010.0618.4 M5 40-94
40.1.3 - Introduction
For easier consultation, this unit has been divided into the following chapters:
l Introduction
m Contains a brief description of the terminology used, the procedures to follow for troubleshooting and repairs, and the
40-6
Wiring diagrams
l Systems
m Contains the wiring diagrams of the tractors systems.
l Wiring harnesses
m Contains the layouts, the wiring diagrams and the positions of connectors on the tractor.
Introduction
This section of the workshop manual is intended as a practical guide to fault diagnosis of the tractors electrical and electronic
systems. The following pages provide the technician with all the necessary information regarding the tractors systems and compo-
nents. Due to the possible time difference between the introduction of technical modifications (in line with our policy of continuous
product improvement) and the corresponding amendment of our printed documentation, the data contained in this document are
subject to modification and as such are not binding.
Definition of components and symbols
To prevent any misunderstanding or ambiguity, definitions for some of the key terms used in this unit are listed below.
Table 105
TERM DESCRIPTION
Connector Element used to connect two components (e.g. wiring-switch, wiring-wiring)
Temperature sensor Electrical component that converts the temperature of a medium (air, water, oil, etc.) into a voltage
or resistance
Pressure sensor Electrical component that converts the pressure of a medium (air, water, etc.) into a voltage or
resistance
Position sensor Electrical component that converts an angular or linear position into a voltage
Pressure switch Switch that changes state (opens or closes a contact) according to the operating pressure in the
circuit in which it is installed
Thermostat Switch that changes state (opens or closes a contact) according to the temperature of the medium
(air, water, etc.) in which it is immersed.
Switch Mechanical component that opens or closes one or more electrical contacts.
Solenoid valve Valve operated by applying electrical current to a coil (or solenoid)
Chapter Components shows the wiring diagrams for certain switches and buttons. The following symbols are used for ease of
interpretation:
Contact between pins CLOSED (stable switch position)
Indicator LED
Indicator light
Diode
General rules
The inspection, maintenance, fault diagnosis and repair operations are essential to ensure that the tractor continues to operate cor-
rectly over time and to prevent malfunctions and breakdowns. This paragraph describes repair procedures and aims to help improve
the quality of repairs.
Modification of the tractors electrical/electronic circuits
The manufacturer prohibits any modification or alteration of the electrical wiring for the connection of any non-approved electrical
appliances or components. In particular, if the electrical system or a component is altered without the Manufacturers authorisation,
the Manufacturer will accept no liability for any damage to the vehicle and the vehicle warranty will be invalidated.
40-7
Wiring diagrams
Main wiring faults
Bad contact between connectors
l The main causes of poor contact between connectors are incorrect insertion of the male into the female connector, deforma-
tion of one or both connectors, and corrosion or oxidisation of the pin contact surfaces.
Defective pin soldering or crimping
l The pins of the male and female connectors make good contact in the crimped or soldered area, but the wires are subjected
to excessive strain, leading to breakage of the insulation and a poor connection or breakage of the wire.
Disconnecting wiring
l If connectors are disconnected by pulling on the cables, or if components are removed with the wires still connected, or if the
wiring is subject to impact by a heavy object this could damage the soldering or crimping of wires on the pins and some wires
may break.
Penetration of water inside connectors
l The connectors are designed to prevent penetration of liquids (water, oil etc.); however, when cleaning the tractor with pres-
sure washers or steam washers water could penetrate or condense in the connectors. As the connectors are designed to
prevent liquid penetration, any water that does get in will be unable to drain out, and thus may cause short circuits across the
pins. It is therefore good practice to dry the connectors with a low pressure jet of compressed air after washing the tractor.
Oil or dirt on connectors
l If the connectors or pin contact surfaces show signs of oil or grease contamination, this will prevent the passage of current
(oil and grease are electrical insulators) creating a poor contact. Clean the connectors thoroughly using a dry cloth or a low
pressure jet of compressed air and use specific products (deoxidising sprays, etc.) to degrease the contacts.
Important
Take care not to bend the pins when cleaning them. Use dry oil-free compressed air.
40-8
Wiring diagrams
l The fitting of replacement fuses that do not comply with these standards will invalidate the warranty with immediate effect and
release the manufacturer from all liability.
l When replacing relays, make sure that the new relay conforms to the standards marked on the original relay.
Diagnostic instruments
For the correct diagnosis of any faults in the tractors electrical system, the following instruments are required:
l Digital multimeter with the following minimum characteristics:
m AC VOLT 0-600
m DC VOLT 0-600
m OHM 0-32M
m AC AMP 0-10
m DC AMP 0-10
40-9
Wiring diagrams
l Conductors,
l Insulators,
l Semiconductors
We therefore need to know what happens electrically inside the material.
All matter is composed of tiny particles called atoms.
The atom can be likened to a planetary system which has at its core a nucleus, comprised of protons and neutrons, around which
rotate the electrons in different orbits, or shells.
Fig. 1105
Under certain conditions, electrons can move from one atom to another.
If the number of electrons in an atom is the same as the number of protons, the atom is neutral (it has no charge).
If the number of electrons exceeds the number of protons, the atom is negatively charged, while if it loses electrons it will become
positively charged.
Atomic structure of matter
The atom is the smallest particle of a simple element that can combine with other
atoms to form molecules.
Fig. 1106
40-10
Wiring diagrams
The composition of the nucleus and the number of electrons present in an atom
determine which element it belongs to.
Fig. 1107
Fig. 1108
Electrical charges of the same sign (1) repel each other while charges of opposite
signs (2) attract.
Fig. 1109
40-11
Wiring diagrams
The concept of voltage or potential difference is illustrated by the example shown
here.
l The levels in A and B are equal if the valve is open.
Fig. 1110
Fig. 1111
When the valve is opened, water flows from A to B until the point where the two
pressures are equalised.
The same happens with electrical current:
l to obtain current flow, there has to be potential difference at one of the
conductor (caused by the presence of electrical charge).
Fig. 1112
Resistance
The water model can also be used to explain the concept of electrical resistance. If water encounters obstacles when flowing through
a pipe the the flow rate will slow or the direction of flow will change .
The same applies to electrical current; obstacles of an electrical nature reduce the flow of electrons. Every material offers some de-
gree resistance to the flow of electrons; the level of this resistance will depend on its atomic structure and its dimensions. Obstacles
in a water course will slow down or change the direction of the water flow.
Electrical resistance can be compared to a restriction in the conductor or scaling
on the inside of a water pipe.
Fig. 1113
40-12
Wiring diagrams
The electrical resistance of a material can be defined as the opposition it presents to the flow of electrons and varies according to the
nature of the material and its dimensions.
Electrical continuity
Staying with the water analogy, lets examine how to obtain a continuous flow of water in a circuit. 424For the flow to be continuous,
the water must be returned to basin 1.
In this hydraulic circuit, the function of the pump (2) is to return the water to basin
or tank (1).
Fig. 1114
Similarly, for current to flow continuously in an electrical circuit, the electrons must return from the positively charged terminal to the
negatively charged terminal, in order to maintain a potential difference between the two terminals. This is the job of the electrical
power source.
Electrical power supply
An electrical power source can be defined as a system capable of separating and initiating the motion of a number of electrons.
A battery, for example, has two metal terminals, one positive and one negative.
Inside the battery, a chemical process causes free electrons to flow to the negative terminal to create a negative charge and a corre-
sponding positive charge to build at the positive terminal.
This process will continue inside the battery until the actions which caused it are balanced by the forces of attraction between the
electrons and the positive charges.
If the electrons could flow to the positive terminal, the initial neutral status could be restored, but as there is internal connection betwe-
en the two terminals, this can only be achieved if there is an external connection between B and A.
We can therefore state that a difference in potential, or voltage, has been created between the two terminals A and B.
If we now connect an external load between B and A, the electrons concentrated at terminal A (+) will starting moving towards terminal
B, thereby pushing along the free electrons present in the connecting conductor.
An electrical current is thus created, (which by convention is deemed as flowing from A to B), and this current will continue to flow as
long as there remains a difference in potential between the two terminals.
Schematic representation of a electrical power source
A = Positive terminal
B = Negative terminal
G = Generator
Fig. 1115
40-13
Wiring diagrams
Electromotive force (e.m.f.)
Taking a simple electrical circuit , lets see what happens to the voltage at the terminals of the power source when the circuit is closed
(in this example, the power source is a battery, but the same result would be obtained with a different source of power, such as an
alternator).
Simple circuit with switch I open: no current flow.
The same situation occurs if we replace the battery with an alternator in rotation.
A voltage (e.g. 12V) is present at the terminals of the power source, which can be
measured with a voltmeter. This no-load voltage is known as the electromotive
force.
R = resistance of a load.
Fig. 1116
Simple circuit with switch I closed. The battery powers the resistance R. A volt-
age drop occurs between the terminals of the power source, caused by the circula-
tion of current in the source itself, which has its own internal resistance.
Vd = r A
r = internal resistance of the power source in series with the other elements of the
circuit
A = current flowing through the circuit
Fig. 1117
40-14
Wiring diagrams
The alternating current wave form illustrated in the graph is called sinusoidal.
T = 1 period
A = Amplitude
B = Positive voltage
C = Negative voltage
Fig. 1118
The number of cycles per second is the FREQUENCY and is expressed in Hertz and denoted with the letter f.
f=1T
T=1f
An AC current with a frequency of 50 Hertz therefore has a period of 1 50 = 0.02 seconds.
Electrical values: Current and Voltage
CURRENT Symbol A
Value: Amount of electrical charge that passes through a conductor in a given unit of time.
Units: amperes.
Instrument: ammeter.
Connection to circuit: In series.
Basic electrical circuit incorporating a voltmeter and an ammeter.
Resistance is present in the conductors (R), in the loads (Ri1) and in the power
source (Ri2).
The inclusion of an ammeter (unlike a voltmeter) requires a modification to the
circuit, in that the circuit must be opened at some point by cutting a conductor and
the instrument must be then connected between the open ends of the conductor.
Fig. 1119
Fig. 1120
VOLTAGE Symbol V
Voltage: Difference in potential; (emf); force that causes electrons to flow
Units: Volts
Measuring instrument: Voltmeter.
Connection to circuit: in parallel.
40-15
Wiring diagrams
Resistance
In an electrical circuit, voltage and current are both dependent on RESISTANCE, i.e. the opposition to the flow of electrons in a
material.
We have already mentioned how the motion of electrons occurs as a result of forces produced by the collision of these minute par-
ticles.
This phenomenon generates heat and is this reason why materials heat up when current passes through them.
The greater the current (the greater the number of electrons in motion) the more heat is produced.
As the temperature increases, the movement of the electrons also increases, and the electrons find it more difficult to move under
the influence of the voltage.
In some materials, this resistance is minimal; these materials are good conductors of current (conductors: copper, aluminium, silver,
etc.). In others, the resistance is so high that it is difficult for electrons to move (insulators: mica, porcelain, glass, paper, etc.)
In addition to the nature of the material, resistance is also affected by its dimensions:
l LENGTH: the greater the length of the conductor the greater the number of collisions between atoms and free electrons.
l CROSS-SECTIONAL AREA; the greater the cross-sectional area, the greater the number of free electrons. Resistance is
inversely proportional to cross-sectional area.
l TEMPERATURE, the motion of atoms and consequently the probability of collision with free atoms increases proportionally
with the temperature, thus increasing also the resistance.
The electrical circuits on the tractor are generally comprised of wire conductors with a cross-sectional area that is negligible in com-
parison with their length.
40-16
Wiring diagrams
The resistance of different materials - Resistivity
It has been determined experimentally that the resistance of a wire conductor is given by:
R = p ( l S ) = ohms
in which:
p = (Greek letter pronounced rho) is a proportional coefficient that varies according to the nature of the material and is known as
resistivity or specific resistance.
l = length, expressed in metres
S = sectional area, expressed in mm
This formula can also be written:
p=(RS)l
so we can state that the unit of measurement of resistivity (p) represents a resistance of 1 ohm of a conductor of the material in que-
stion, with a length 1 metre, and sectional area of 1 mm, at a temperature of 0C.
While for conductors resistivity is measured in ohms per mm/m, for insulators it is almost always expressed in mega ohms/mm,
which is the resistance in millions of ohms of a cube with a side length of 1 m.
Variation of resistance with temperature (temperature coefficient)
For most metals, resistivity increases with the temperature (positive temperature coefficient); this is why when talking about resistivity
there must always be a reference to temperature.
There are exceptions to this rule, such as, for example, chromium and carbon, in which resistivity decreases with the temperature
(negative temperature coefficient) and some alloys in which resistivity does not vary, which have temperature coefficient of 0.
This increase or decrease in the resistance per degree of temperature and per ohm of resistance is termed the temperature coeffi-
cient , and is denoted with the Greek letter a (alpha).
If the initial resistance is R0, at a temperature t0 (ambient temperature), and the temperature difference is t = t1 - t0, the variation in
resistance will be:
Rta
and the final resistance is:
Rt = R0 + R0 t a
Rt = R0 (1 + a t0)
This formula is of great practical importance as it allows us to calculate the final temperature of a coil or resistor using the resistance
variation method.
The temperature coefficient is used (positive or negative) to characterise thermistors (PTC = Positive Temperature Coefficient and
NTC = Negative Temperature Coefficient)
The interdependence of electrical values
In an electrical circuit, the relationship between current, voltage and resistance is given by the formula:
V=IxR
Volts = ohms x amps
If any of these values is unknown, it can be calculated, providing the other two values are known, simply by applying one of the
following formulae:
R=VI
I=VR
V=IxR
Power
The power developed or dissipated is given by the formula:
Power = Voltage x Current
Watt (W) = Volts x Amps
In mechanical engineering, power is still commonly expressed in terms of horsepower: hp
The relationship between horsepower and Watts is given in the following equation:
1 hp = 736 W = 0.736 kW
1 kW = 1.36 hp
40-17
Wiring diagrams
Dissipated power, in electrical terms, is power transformed into heat and is given by:
Power = Voltage x Current = Resistance x Current x Current
given that:
W=VI
V=RI
then:
W = R I I = R I
Multiples and submultiples of electrical values
Table 107
Multiples and submultiples of units of measurement
Prefix Multiply by Divide by
Name Symbol
mega- M 1,000,000 -
kilo- k 1000 -
hecto- h 100 -
deca- da 10 -
deci- D - 10
centi- S - 100
milli- M - 1.000
micro- - 1,000,000
nano- N - 1,000,000,000
pico- P - 1,000,000,000,000
40-18
Wiring diagrams
Fixed resistors
How to determine the ohmic value of a resistor
In wirewound resistors, the value is printed with decimal point (or comma) and the
omega symbol.
If the value of the resistor is 10.5 ohms, the marking will be: 10.5 ohms
sometimes the letter R is used in place of the decimal separator (point or comma):
10 R5
On resistors with values measured in thousand of ohms, the printed value will
include the letter k, which stands for thousand (1000): 10.5 kohms (10,500 ohms)
Fig. 1122
Fig. 1123
Fig. 1124
Fig. 1125
40-19
Wiring diagrams
Preventing arcing between the resistor and sliding contact.
The figure shows a way to prevent the arcing between the resistor and the sliding
contact that may occur in the case of poor contact.
This connection allows some of the current to flow through the full length of the
resistor. The voltage drop between the sliding contact and the resistor is less than
V1, thus reducing the possibility of arcing.
The resistor of the rheostat can be sized so that the resistance can be varied in
both a linear and a non-linear way.
Fig. 1126
Voltage divider
Voltage dividers with fixed resistors or potentiometers are used whenever circuits require electrical power below the standard volta-
ges available on the tractor (12 Volts with engine off and 14.5 Volts with engine running).
Voltage dividers are found in the voltage regulator of the alternator and in the electronic control units.
Thermistors (Thermally Sensitive Resistors)
These are semiconductor resistors in which the resistance decreases as the temperature rises, ranging from just a few ohms at 0 C
to tens of thousands of ohms at 100 C; they are used to detect changes in temperature.
They may be either self-heating, if the heat is produced by the current flowing through them, or externally heated, if sensitive to the
temperature of the environment or the component on which they are mounted.
There are two types: PTC (Positive Temperature Coefficient) and NTC (Negative Temperature Coefficient)
With PTC thermistors, resistance increases with the temperature, while with the NTC type, resistance decreases as the temperature
rises.
NTC types are available with resistance values ranging from just a few ohms to several hundred kohms.
Operating characteristics of NTC thermistors
Fig. 1127
Fig. 1128
40-20
Wiring diagrams
Capacitor
This component consists of a pair of conductors, generally in the form of flat plates, separated by an insulator (dielectric). Its function
to store electrical charge from a power supply.
This charge can then be given as and when required.
Symbol
Fig. 1129
Fig. 1130
The amount of electrical charge that a capacitor can store is referred to as its capacitance (C), and is measured in farads (F). In
practice, however, the farad is too large for general use so the following units are used instead:
mF = millifarad = 1/1,000 F
F = microfarad = 1/1,000,000 F
nF = nanofarad = 1/1,000,000,000 F
On closing the switch, the electrons start moving but their flow is impeded by the dielectric. Electrons will therefore accumulate in the
plate connected to the negative terminal (-) of the generator, causing negative charge to build up. In the meantime the positive plate
loses electrons, thereby becoming positively charged. A potential difference is thus created across the plates of the capacitor, and
this increases until it equals the potential difference of the generator.
The capacitance of the capacitor is therefore proportional to the applied voltage and to the surface area of the plates and is inversely
proportional to the distance d between the plates. It also depends on the type of dielectric used.
The process described above is known as charging the capacitor, and is complete when the capacitor is fully charged. If a resistor
or a load of another type is connected to the capacitor, the latter discharges as electrons flow in opposite direction and the potential
difference between the plates decreases to zero.
Diodes
A diode can be defined simply as a junction between two semiconductors, one made of P-type material and the other made of N-type
material.
40-21
Wiring diagrams
A diode is a junction between two semiconductors, one made of P type material
and the other made of N type material.
Fig. 1131
The contact between the two semiconductors in different situations of electrical charge forms a barrier to electrical current flow at
the junction.
This barrier prevents the current from flowing through the diode.
Fig. 1132
Fig. 1133
Fig. 1134
The situation at the junction between the two semiconductors changes when a voltage is applied across the anode and cathode; the
diode is polarised, as shown in the figure.
When a voltage is applied to the diode, it polarises in the two ways indicated.
40-22
Wiring diagrams
(A) = Direct polarisation (forward biasing)
( - ) = Cathode
( + ) = Anode
Fig. 1135
Fig. 1136
With forward biasing (positive connected to the anode and negative to the cathode) the resistance to current flow is significantly
reduced and the diode allows current to flow, providing that the applied voltage exceeds the threshold value, i.e. the voltage required
to initiate the process by which the barrier is reduced.
If the polarity of the diode is reversed, there is no electron flow except for the very weak current that crosses the junction. If the rever-
se voltage applied to the diode exceeds a certain value (thousand of Volts) the reverse current flowing through the diode will increase
rapidly to the point where the junction is damaged.
The function of the diode is therefore to allow current flow in one direction only, from the anode (+) to the cathode ( - ).
It this way it acts as an electrical one-way valve.
Forward biased diode allows current flow.
The lamp illuminates,
Fig. 1137
40-23
Wiring diagrams
Reverse biased diode blocks current flow.
The lamp does not illuminate.
Fig. 1138
Fig. 1139
Zener diode
We have already mentioned how diodes do not tolerate reverse voltage, as when this reaches a certain level, the reverse current flow
will increase significantly to the point where the diode itself is damaged.
The Zener diode is specifically designed to allow a certain amount of reverse current flow without damage to the junction.
It is also possible to make this reverse current flow occurs at a certain reverse voltage, known as zener voltage.
A zener diode can therefore be defined as semiconductor with a special PN junction with controlled reverse bias properties.
If forward biased, the Zener diode behaves just like a normal diode, while if reverse biased, it prevents current flow until the voltage
reaches the critical level, which is defined as the Zener point.
At this point the current increases rapidly.
40-24
Wiring diagrams
Fig. 1140
The behaviour of the Zener diode can thus be compared to that of a pressure relief valve in a hydraulic circuit.
a) current and water flow
b) no current or water flow,
c) the water flows when it overcomes the opposing force of the valve spring. Likewise, the current flows when the voltage reaches
the zener point.
LED (light emitting diode)
A LED is a special diode with two terminals; it allows current flow in one direction only and emits light when low-voltage current pas-
ses through it.
The polarity of the terminals is very important, and the cathode is marked to facilitate identification.
The light emitted is monochromatic; the colours red, yellow, green and orange are available.
Operating characteristics of a LED and its symbol.
Fig. 1141
40-25
Wiring diagrams
LED
1. Light beam emitted
2. Diode
3. Transparent plastic cap
4. PIN terminals
Fig. 1142
LEDs are often used for signal lamps as their power consumption is very low, they require only low levels of reverse current and they
are impact resistant.
A typical application is as an indicator lamp, which, unlike a conventional bulb, can be flashed on and off repeatedly without failing.
They are also used to display segmented symbols and alphanumeric digits.
40.1.7 - Electrical and electronic components (2/2)
Transistors
A transistor is semiconductor which has three junctions.
It can be distinguished from a diode by its three leads, whereas a diode only has two.
40-26
Wiring diagrams
When voltage is applied across terminals (E) and (C), no current flows through
the transistor.
Fig. 1144
If a weak voltage is applied simultaneously to the base terminal, the transistor becomes a conductor and current flows between the
emitter and collector.
When voltage is also applied to the base terminal, the transistor allows current
flow.
Fig. 1145
When the voltage applied to the base terminal is modified, the current flow between the emitter and collector will also vary proportio-
nally. From this behaviour are derived the two main characteristics of the transistor:
1. Current does not flow through the transistor if the circuit between the emitter and collector is interrupted, i.e. no voltage ap-
plied.
2. The current flowing through the transistor is directly proportional to current that flows through the emitter-base circuit, within
the operating limits of the transistor. This means that the base current (the current that flows between the emitter and base) is
proportional to the collector current (the current flow between the emitter and the collector) and therefore the latter increases.
Given these two characteristics, a transistor can function as a switch (by removing the voltage at the base) or as an amplifier.
With a transistor, a weak current flowing from the emitter E to the base B (PNP transistor) or from the base to the emitter (NPN
transistor), can be used to control a strong current flow from the emitter to the collector (PNP) or from the collector to emitter (NPN).
This is the most useful characteristic of the transistor, which can be summarised in the equation:
a = ( Ic ) ( Ib )
This parameter, however, varies according to the collector current and voltage, as well as the temperature of the transistor.
The difference between NPN-type and PNP-type transistors lies solely in the direction of the current flow. The operating limits of
transistors are:
l the maximum collector current,
l maximum voltage from collector to emitter.
40-27
Wiring diagrams
Fig. 1147
Typical connection of a transistor. The resistor R limits the current and protects the transistor.
40-28
Wiring diagrams
Fig. 1148
Typical connection of a transistor. The resistor R limits the current and protects the transistor.
Fig. 1149
The transistor as a current amplifier
Use of a transistor as a switch or relay
Thanks to their amplifying properties, transistors can be used in place of relays (electromagnetic switches) as they can perform the
same function, but with the advantage that they use static components rather than moving parts.
The figure shows two electrical circuits, one controlled by a relay and the other by a transistor.
In the relay circuit, when the switch is closed in the relay control circuit, the contacts close the main circuit (drawn with the thick black
line); i.e. a relatively small current (0.2 A) can be used to control a much larger working current (8A).
The transistor circuit works in exactly the same way. When the switch in the control circuit is closed, the current flows from the positive
pole of the battery through the emitter; the base terminal of the transistor is polarised and the transistor allows current flow (EC) thus
allowing current to flow in the main circuit.
40-29
Wiring diagrams
Fig. 1150
Circuit diagrams show use of an electromagnetic relay (B) and use of a transistor as a relay (A). U = Load in main circuit.
40-30
Wiring diagrams
40.2 - Components
40.2.1 - Components
This chapter contains:
l Components table: technical and functional description of the components
l Pinouts of the electronic control units
Component technical data
Table 109
Description Code Characteristics Connector
Bosch emergency pushbutton 2.7659.110.0 - A7
Check panel 2.8339.230.0 - A18
2.8339.230.4 A20
Steering column switch 0.013.3337.3 - A25
Flasher 0.009.6758.4/10 - A26
Windscreen wiper timer relay 2.8639.008.0 G9
Fig. 1151
Worklights d.80 2.8039.001.0 G14
Fig. 1152
Windscreen wiper 2.9019.200.0 G19
Fig. 1153
40-31
Wiring diagrams
Description Code Characteristics Connector
Rear wiper 2.9019.200.0 L4
Fig. 1154
Receiver-dryer 0.008.9604.0 - M3
M4
Air conditioning fan 0.010.0618.4 - M5
Ex rotating beacon wire 0.013.9053.2 N1
Fig. 1155
RH light 2.8039.293.0 - P2
2.8039.293.0 P3
LH light 2.8039.294.0 - P5
2.8039.294.0 P6
Rear lights 2.8059.230.0 - S2
(LH) S3
S4
Rear lights 2.8059.240.0 - S6
(RH) S7
S8
40-32
Wiring diagrams
Description Code Characteristics Connector
Fan control unit 2.8519.035.4 U1
Fig. 1156
PTO switch 2.7659.262.0 V4
Fig. 1157
Front lights 2.8039.230.0 - Z5
Z8
40-33
Wiring diagrams
PIN VOLTS SYMBOL DESCRIPTION
9 - L7A Handbrake on warning light (red)
10 - L8A Conv. oil pressure warning light (red)
11 - L9A Alarm warning light (red)
12 +12V + Positive (+12V)
Instrument panel (CODE 2.8339.230.0/70) - A19
Table 112
PIN VOLTS SYMBOL DESCRIPTION
1 +12V + Positive (+12V)
2 - - N.C.
3 - - N.C.
4 - S ILC instrument signal
5 - +L Lighting (+lights)
6 - GND Earth
Instrument panel (CODE 2.8339.230.0/70) - A20
Table 113
PIN VOLTS SYMBOL DESCRIPTION
1 - GND Earth
2 - L1B Differential lock indicator light (amber)
3 - L2B Front wheel drive engaged (yellow)
4 - L3B Low fuel warning light (yellow)
5 - L4B Trailer brakes alarm warning light (red)
6 - L5B Direction indicators warning light (green)
7 - L6B Trailer direction indicators warning light (green)
8 - L7B Sidelights warning light (green)
9 - L8B Full beam headlights warning light (blue)
10 - L9B PTO clutch indicator light (red)
11 - L1B N.C.
12 +12V + Positive (+12V)
Instrument panel (CODE 2.8339.230.0/70) - A21
Table 114
PIN VOLTS SYMBOL DESCRIPTION
1 - GND Earth
2 - +L Lighting (+lights)
3 - S2 TA instrument signal
4 +12V +12 Positive (+12V)
5 - +24 N.C.
Instrument panel (CODE 28993.230.0/70) - A22
Table 115
PIN VOLTS SYMBOL DESCRIPTION
1 - GND Earth
2 - +L Lighting (+lights)
3 - 5 Temperature gauge signal
4 - - N.C,
5 - - N.C.
6 +12V + Positive (+12V)
40-34
Wiring diagrams
40.3 - Systems
40.3.1 - Earthing points
Radar earthing points
40-35
Wiring diagrams
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
U8 C2
Fig. 1167
40-36
Wiring diagrams
40.3.2 - Starting
40-37
Wiring diagrams
40-38
Wiring diagrams
40.3.3 - Control unit - Fan
Fig. 1169
Key
l U1 Control unit
l U2 Fan
l U3 Indicator light
l U4 Temperature
l U5 Temp
l U6 Female connector terminal
l U7 Male connector terminal
l U8 Earth
l Z13 Fuel lift pump
l Z15 Engine coolant temperature sensor for warning light
Wiring and connectors list
l 0.014.1482.4 - Fan wiring
m See para. 40.4.13 - Solenoid valve wiring ... - page 40-80
m See para. 40.4.14 - Positions of solenoid ... - page 40-81
40-39
Wiring diagrams
40.3.4 - Steering column lights switch
40-40
Wiring diagrams
40-41
Wiring diagrams
40-42
Wiring diagrams
l 0.013.1452.4/10 - Rear wiring
m See para. 40.4.15 - Rear wiring - 0.013.14... - page 40-82
m See para. 40.4.16 - Positions of rear wiri... - page 40-84
40-43
Wiring diagrams
40-44
Wiring diagrams
Wiring and connectors list
l 0.012.6949.4 - Central wiring
m See para. 40.4.11 - Central wiring - 0.012... - page 40-71
m See para. 40.4.12 - Positions of central w... - page 40-74
40.3.6 - Cab
40-45
Wiring diagrams
40-46
Wiring diagrams
40-47
Wiring diagrams
l 0.014.7596.4 - Air conditioning system wiring
m See para. 40.4.24 - Air conditioning syste... - page 40-94
m See para. 40.4.25 - Position of air condit... - page 40-94
40-48
Wiring diagrams
40-49
Wiring diagrams
Wiring and connectors list
l 0.014.7593.4 -Aereo-cab wiring
m See para. 40.4.20 - Aereo cab wiring - 0.0... - page 40-89
m See para. 40.4.21 - Positions of aereo-cab... - page 40-90
40-50
Wiring diagrams
40.3.8 - PTO
40-51
Wiring diagrams
l A36 To rear wiring
l A40 Starter motor
l C1 To central wiring
l C2 Earth
l C11 PTO speed indicator light switch switch
l C12 PTO speed indicator light switch switch
l D1 To central wiring
l D2 To PTO wiring
l D3 Flow control switch
l D4 To platform wiring
l V1 To central wiring
l V2 PTO brake
l V3 PTO
l V4 PTO switch
Wiring and connectors list
l 0.012.6949.4 - Central wiring
m See para. 40.4.11 - Central wiring - 0.012... - page 40-71
m See para. 40.4.12 - Positions of central w... - page 40-74
40-52
Wiring diagrams
40.3.9 - Front axle differential lock
40-53
Wiring diagrams
40-54
Wiring diagrams
40.3.10 - Brakes
40-55
Wiring diagrams
l S1 To rear wiring
l S2 To LH rear lights
l S5 To rear wiring
l S6 To RH rear lights
Wiring and connectors list
l 0.012.6949.4 - Central wiring
m See para. 40.4.11 - Central wiring - 0.012... - page 40-71
m See para. 40.4.12 - Positions of central w... - page 40-74
40-56
Wiring diagrams
40.4 - Wiring harnesses
40.4.1 - Wiring harnesses
40-57
Wiring diagrams
40-58
Wiring diagrams
View of wiring
40-59
Wiring diagrams
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
Z5 Z6
40-40 40-40
Z7
40-40
40-60
Wiring diagrams
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
Z15 -
40-39
40-43
Fig. 1191
40-61
Wiring diagrams
Connector positions
Table 118
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
V1 V2
40-43 40-50
40-50 V3
40-50
Fig. 1195
40-62
Wiring diagrams
40.4.5 - Front lights wiring - 0.014.7599.4
40-63
Wiring diagrams
40.4.6 - Positions of front light wiring connectors
View of wiring
40-64
Wiring diagrams
40.4.7 - Compressor wiring - 0.014.7601.4
40-65
Wiring diagrams
Connector positions
Table 120
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
R1 R2
40-66
Wiring diagrams
40-67
Wiring diagrams
40-68
Wiring diagrams
View of wiring
40-69
Wiring diagrams
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
Z5 Z6
40-40 40-40
Z7
40-40
40-70
Wiring diagrams
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
Z15 -
40-39
40-43
Fig. 1218
40-71
Wiring diagrams
40-72
Wiring diagrams
40-73
Wiring diagrams
40-74
Wiring diagrams
40.4.12 - Positions of central wiring connectors
View of wiring
40-75
Wiring diagrams
Connector positions
Table 122
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
A1 A3
40-37 40-37
40-52 40-52
40-40 40-40
40-76
Wiring diagrams
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
A10 A11
40-52 40-50
40-50 40-52
40-37 40-43
40-43 40-43
40-77
Wiring diagrams
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
A18 A23
40-37 40-37
40-40 40-43
40-43 40-52
40-50
40-52
40-55
A19
40-37
40-40
40-43
40-52
40-50
40-55
A20 Fig. 1234 Fig. 1235
40-37
40-40
40-43
40-50
40-52
A21
40-37
40-40
40-43
40-52
A22 -
A24 A25
40-37 40-40
40-37
40-43
40-52
40-78
Wiring diagrams
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
A30 A31
40-37 40-37
40-40 40-40
40-52 40-43
40-52
40-79
Wiring diagrams
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
A39 A41
40-37 40-43
A40
40-37
40-50
40-80
Wiring diagrams
40.4.14 - Positions of solenoid valve wiring connectors
View of wiring
40-81
Wiring diagrams
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
U4 U5
40-39 40-39
40-82
Wiring diagrams
Fig. 1259
40-83
Wiring diagrams
40.4.16 - Positions of rear wiring connectors
View of wiring
40-84
Wiring diagrams
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
C3 C4
40-52 40-55
Fig. 1264
Fig. 1263
C5 C6
40-40 40-40
40-55
C7
40-40
40-55
C8
C9
40-40
40-85
Wiring diagrams
40.4.17 - Remote valve wiring - 0.012.6955.4
40-86
Wiring diagrams
40.4.19 - Positions of rear light wiring connectors
View of wiring
40-87
Wiring diagrams
View of wiring
40-88
Wiring diagrams
40.4.20 - Aereo cab wiring - 0.014.7593.4
40-89
Wiring diagrams
40-90
Wiring diagrams
40.4.21 - Positions of aereo-cab wiring connectors
View of wiring
40-91
Wiring diagrams
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
G14 G8
40-45 40-48
40-48 G9
G15 40-48
40-45 G10
40-48 40-48
40-45
G11
40-48
40-45
G12
40-48
G13
40-48
Fig. 1279 G16 Fig. 1280
40-45
40-48
G17
40-48
G18
40-48
40-92
Wiring diagrams
40.4.23 - Positions of cab power supply wiring connectors
View of wiring
40-93
Wiring diagrams
40.4.24 - Air conditioning system - 0.014.7596.4
40-94
Wiring diagrams
40.4.25 - Position of air conditioner wiring connectors
View of wiring
40-95
Wiring diagrams
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
M3 M5
40-48 40-45
M4
40-45
40-96
Wiring diagrams
40.4.27 - Positions of cab earth wiring connectors
View of wiring
40-97
Wiring diagrams
40.4.28 - Worklights-number plate light- flashing light - 0.014.7595.4
40-98
Wiring diagrams
Fig. 1297 - Positions of worklight, number plate and flashing light wiring connectors
0.014.7595.4
l See para. 40.4.28 - Worklights-number plat... - page 40-98
40-99
Wiring diagrams
Connector positions
Table 130
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
L1 L2
40-45 40-40
40-48 40-45
T3
40-45
40-100
Wiring diagrams
40.4.30 - Flashing light wiring - 0.014.7591.4
40-101
Wiring diagrams
Connector positions
Table 131
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
N1
40-45
N2
N3
Fig. 1306
40-102
Wiring diagrams
40.4.33 - Positions of windscreen wiper wiring connectors
View of wiring
40-103
Wiring diagrams
40.4.34 - Radio wiring - 0.014.7600.4
40-104
Wiring diagrams
40.4.35 - Positions of radio-loudspeaker wiring connectors
View of wiring
40-105
Wiring diagrams
Connector positions
Table 133
Connec- Connector positions Connec- Connector positions
tor/Sys- tor/Sys-
tem tem
Q1 Q3
40-45 40-45
Q2
40-45
Fig. 1315
40-106
INDEX
A
A/C fan - compressor drivebelt 30-29
A/C system air intake filters 30-225
Adjustable front fenders 30-217
Adjustment of the bevel gear pair 30-162
Adjustment of the brake light switches 30-273
Adjustment of the lift control valve levers 30-240
Adjustment of the parking brake switch 30-271
Adjustment of the rear lift 30-293
Aereo cab 40-48
Aereo cab wiring - 0.014.7593.4 40-89
Air cleaner assembly 30-97
Air conditioner fan 30-238
Air conditioning compressor 30-233
Air conditioning system - 0.014.7596.4 40-94
Air conditioning system - Standard roof version 30-230
Alternator 30-109, 30-111
Auxiliary fuel tank 30-103
B
B0 - Engine 30-2
Baruffaldi electromagnetic clutch 20-2
Basic electronics for mechanics (1/2) 40-9
Basic electronics for mechanics (2/2) 40-11
Battery 30-267
Bevel gear pair 30-149
Bistable pressure switch for compressor clutch engagement/disengagement 30-239
Brake lights switches 30-271
Brakes 40-55
Brakes and rear axle assembly 10-13
C
C0 - Engine accessories 30-93
Cab 30-205, 40-45
Cab access steps 30-216
Cab door lock - tie-rod 30-217
Cab earth wiring - 0.015.0031.4 40-96
Cab power supply - 0.014.7594.4 40-92
Cab roof 30-226
Central wiring - 0.012.6949.4 40-71
Centre console 30-224
Checking clutch plate wear 30-128
Clutch housing 30-131
Clutch plate 30-127
Clutch release bearing 30-128
Clutch release forks 30-129
Components 40-31, 40-31
Compression test 30-11
Compressor wiring - 0.014.7601.4 40-65
Condenser 30-235
Control buttons - RH console 30-273
Control rods 30-264
Control unit - Fan 40-39
Conversion factors 0-10
Cooling system 30-85
Crankshaft pulley 30-31
Creeper - synchronizer renewal 30-155
Cylinder 30-285
Cylinder head and valve train components 30-55
D
D0 - Transmission 30-127
Diagnostic tool screens 20-2
Differential lock control assembly 10-17
I
INDEX
Disassembly of 4WD output shaft and groundspeed PTO 30-153
Disassembly of LH/RH rear axle 30-167
Disassembly of the bevel gear pair 30-190
Disassembly of the gearbox input shaft 30-135
Disassembly of the lift control valve 30-302
Disassembly of the main shaft 30-137
Disassembly of the planetary reduction gear 30-199
Disassembly of the PTO output shaft. 30-158
Disassembly of the rear differential 30-175
Disassembly of the secondary shaft 30-137
Disassembly of the starter motor 30-120
Double/single acting conversion valve 30-264
E
E0 - Rear axle 30-166
Earthing points 40-35
Electrical and electronic components (1/2) 40-18
Electrical and electronic components (2/2) 40-26
Electrostatic unit 30-269
Engine 30-10
Engine - Separation from the transmission 30-3
Engine air intake pipe 30-89
e
engine block, crankshaft, pistons and sump 30-13
E
Engine cooling system radiator 30-93
Engine stop keyswitch 30-104, 30-107
Evaporator assembly 30-237
Exhaust pipe - tractor with cab 30-105
Expansion tank 30-96
F
F0 - Front axle 30-178
Fan 30-97
Fan - alternator drivebelt 30-26
Flashing light wiring - 0.014.7591.4 40-100
Flywheel bearing 30-33
Front axle 10-14, 10-14
Front axle - complete assembly 30-182
Front axle differential lock 40-52
Front lift - version with front PTO - 30-283
Front lights wiring - 0.014.7599.4 40-62
Front PTO wiring - 0.014.2645.4 40-61
Front support 30-178
Front wheels 30-309
Front wiring with cab 40-66
Fuel filter 30-99
Fuel injection nozzle 30-79
Fuel System 30-66
Fuel tank - Fuel tank float switch 30-99
Fuse and relay assembly 30-268
G
G0 - Bodywork - Cab - Platform 30-205
Gear pump 10-17
Gearbox and shuttle assembly - complete unit 30-141, 30-142
Gearbox input shaft - oil seal renewal 30-148
General safety rules 0-2
Governor 30-82
II
INDEX
H
H0 - Hydraulic system 30-244
Hood and side panels 30-212
Hydraulic lift control valve 30-301
Hydraulic system 10-17
I
Injection pump 30-71
Inspection and adjustment of the fuel system 30-69
Inspection of the air intake and exhaust system 30-91
Inspection of the camshaft 30-48, 30-49
Inspection of the connecting rods 30-47
Inspection of the cooling system 30-87
Inspection of the crankshaft 30-23
Inspection of the cylinder head 30-62
Inspection of the engine monobloc 30-23
Inspection of the flywheel and ring gear 30-44
Inspection of the fuel injection pump camshaft 30-78, 30-79
Inspection of the fuel lift pump 30-70
Inspection of the idler gear 30-50
Inspection of the lubrication system 30-65
Inspection of the pistons, piston rings and gudgeon pins 30-44
Inspection of the rocker arms and rocker shaft 30-55
Inspection of the valve pushrods 30-62
Inspection of the valve springs 30-62
Inspection of the valves, valve guides and valve seats 30-50
Instrument panel 30-219, 30-223, 40-43
Intake and exhaust systems 30-90
Introduction 0-2, 40-2, 40-6
L
L0 - Electrical system 30-267
Left-hand console 30-221
Left-hand rear axle 30-166
Left-hand rear cab pillar - screenwash reservoir 30-220
Lift arms 30-299
Lift cylinders 30-296, 30-297
Lift locking shut-off valve 30-261
Lifting instructions 0-4
Lubrication System 30-63
M
M0 - Front PTO 30-276
Maintenance of the injector nozzles 30-82
N
N0 - Front lift 30-283
O
Operator seated sensor ECU (p/n 2.8519.106.0) 20-8
P
Parking brake 30-160
Parking brake switch 30-270
III
INDEX
Planetary reduction gear 30-199
Position of air conditioner wiring connectors 40-94
Positions of aereo-cab wiring connectors 40-90
Positions of cab earth wiring connectors 40-96
Positions of cab power supply wiring connectors 40-93
Positions of central wiring connectors 40-74
Positions of compressor wiring connectors 40-65
Positions of flashing light wiring connectors 40-101
Positions of front light wiring connectors 40-63
Positions of front PTO wiring connectors. 40-61
Positions of front wiring connectors 40-58
Positions of front wiring connectors with cab 40-68
Positions of radio-loudspeaker wiring connectors 40-104
Positions of rear light wiring connectors 40-87
Positions of rear wiring connectors 40-84
Positions of solenoid valve wiring connectors 40-81
Positions of windscreen wiper wiring connectors 40-102
Positions of worklight, number plate and flashing light wiring connectors 40-99
Power steering disassembly 30-247
Power steering valve 10-22
Power steering valve - Complete assembly 30-246
PREPARATION FOR DISASSEMBLY 30-2
Pressure relief valve - lift control valve 30-260
Propeller shaft - Front axle drive shaft 30-198
PTO 40-50
PTO output shaft 30-279
PTO output shaft. 30-157
Pump - clutch assembly - brake 30-276
Pump for hydraulic lift and auxiliary services and power steering system 30-244
R
R0 - Rear lift 30-287
Radio wiring - 0.014.7600.4 40-104
Range gearbox and differential assembly - complete unit 30-146
Rear axle 10-13
Rear axle brake discs 30-176
Rear differential 30-172
Rear lift - complete assembly 30-287, 30-289
Rear lights wiring - 0.014.7602.4 40-86
Rear PTO and Mid PTO 10-8
Rear wheels 30-309
Rear wiring - 0.013.1452.4/10 40-82
Receiver-dryer 30-236
Remote control valve 10-22, 30-262, 30-262
Remote valve control levers 30-243
Remote valve wiring - 0.012.6955.4 40-86
Removal of the PTO output shaft 30-158
Renewal of the jets 30-62
Renewal of the rear lift bush 30-298
RH rear cab pillar trim 30-224
Right-hand console 30-221
S
S0 - Wheels 30-309
Safety notes 0-2
Safety precautions for removal and refitting operations 0-3
Seat 30-230
Solenoid valve 30-281
Solenoid valve wiring - 0.014.1482.4 40-80
Starter motor 30-116, 30-118
Starting 40-37
Steering circuit 10-20
Steering column lights switch 40-40
Steering column switch 30-273
Steering cylinders 30-184
Steering cylinders disassembly 30-186
Steering knuckle housing and axle shaft 30-188
Steering wheel 30-240
Structure of the unit 40-2
Support and towing hitch 30-310
Systems 40-35
IV
INDEX
T
Threadlockers, adhesives, sealants and lubricants 0-8
Three-point linkage with mechanical adjustment 30-307
Tightening torques 0-5
Timing gears and flywheel 30-33
Transmission 10-2, 10-2
Transmission oil filter assembly 30-244
V
V0 - Ballast - towing hitches 30-310
Valve clearances 30-53
W
Windscreen wipers - 0.014.7598.4 40-102
Wiring and components index 40-6
Wiring harnesses 40-57, 40-57
Worklights-number plate light- flashing light - 0.014.7595.4 40-98
V
MODIFICATIONS SINCE LAST VERSION
Operator seated sensor ECU (p/n 2.8519.106.0) 20-8
VI
*307.W.0430.en.6.02*
04/2015
SAME DEUTZ-FAHR ITALIA S.p.A.
Viale F. Cassani, 15 - 24047 Treviglio (BG) Italy
T + 39.0363.4211 F + 39.0363.421638
www.samedeutz-fahr.com
Deutz-Fahr is a trademark
www.deutz-fahr.com