Académique Documents
Professionnel Documents
Culture Documents
IND EX PAGE
Insulation technology in
instrument transformers.
BERROSTEGUIETA, JAIME
Electrotcnica Arteche Hnos., S.A.
Resumen Abstract
Se describen en primer lugar la tecnologa utilizada actual- The technology now used to construct insulation in high-vol-
mente en la construccin del aislamiento de los transfor- tage instrument transformers is described. New materials
madores de medida de alta tensin. Los nuevos materiales are discussed as alternatives in design and likely trends for
se comentan como alternativa de diseo y posible tenden- the future. Finally, various methods are described to assure
cia futura. Finalmente se describen diversos mtodos para manufacturing quality and the condition of transformers in
asegurar la calidad en la fabricacin y el estado de los service.
transformadores en servicio.
1. INTRODUCCIN 1. INTRODUCTION
Aunque el objetivo principal de un transformador de medida Although the main purpose of a instrument transformer (IT)
(TM) es transformar con precisin las magnitudes de ten- is to transform accurately voltage or current to standardized
sin o intensidad a valores normalizados, tanto en rgimen levels in both transient and established regimes, if it is con-
transitorio como establecido, si est conectado a una lnea nected to a high voltage line its electrical insulation function
de alta tensin su funcin de aislamiento elctrico adquie- is also highly important.
re gran importancia.
Tanto por su utilizacin como por el aislamiento empleado Medium voltage (3.6 - 72.5 kV) must be distinguished from
cabe diferenciar claramente la media tensin (3,6 a 72,5 high voltage (72.5 - 765 kV) in terms of use and the insu-
kV) de la alta tensin (72,5 a 765 kV), siendo esta ltima lation employed. The high voltage units are the main subject
el tema principal de este artculo. of this article.
1
Existen tres tipos de TM:
1) Transformadores de intensidad (TI) destinados a trans-
formar la intensidad de la lnea en la que estn conectados
en serie (fig. 1).
2) Transformadores de tensin, tanto inductivos (TTM)
como capacitivos (TTC), destinados a transformar la ten-
sin entre la lnea y tierra (fig. 2 y 3); y
3) Transformadores Combinados (TMC) formados por un TI
y un TTM (fig. 4). El aislamiento de los TI, TTM y TTC difiere
substancialmente entre s, por lo que se analizar separa-
damente.
2. DESCRIPCIN TCNICA
2. TECHNICAL DESCRIPTION
The appearance of epoxy type synthetic resins enabled the
same material to be used for the inside and outside insu-
Fig. 1. Transformador de intensidad lation of medium voltage, indoor ITs (fig. 5). Later, cycloa-
Current transformer
liphatic resins and materials such as butyl which behave
2
rior (fig. 6). No obstante en estos casos la lnea de fuga better against surface electric arcs and UV rays enabled the
debe ser superior a la utilizada en los aisladores de por- same technique to be used in designs for ITs for outside
celana debido a su carcter orgnico y consiguiente use (fig. 6). However in these cases the leakage path must
menor resistencia a los citados arcos elctricos. be greater than that used in porcelain insulators because
they are organic and therefore less resistant to the mentio-
Es posible combinar las ventajas de fabricacin del aisla- ned electric arcs.
miento slido con una elevada resistencia externa, median-
te un diseo como el de la figura 7, donde se combinan la The manufacturing advantages of solid insulation can be
resina epoxi con la porcelana en un TM de media tensin. combined with high outside strength in designs such as the
En este caso debe garantizarse la estanqueidad de la one in fig. 7, where epoxy resin is combined with porcelain
cmara entre ambos elementos para evitar que se hume- in a medium voltage IT. In this case the leak-tightness fo the
dezca y como consecuencia de ello se produzca un arco chamber between the two parts must be ensured to prevent
entre alta y baja tensin a travs de dicha cmara. moisture getting in and causing an electric arc between the
high and low voltage across the chamber.
A pesar de diversas experiencias en la utilizacin de estos
materiales en alta tensin, se ha comprobado que no son Various trials have been carried out with these materials in
aconsejables para tensiones superiores a 72 kV por lo que high voltage, but they have been found to be unsuitable for
se sigue empleando el papel-aceite como aislamiento voltages of more than 72 kV. Oil paper is therefore still used
interno, aunque es un procedimiento ms laborioso, y por- in internal insulation, in spite of the process being more
celana para el exterior. laborious, and porcelain for the outside.
3
In new designs the diameter of the porcelain parts has
been reduced, with which the flashover voltage is increa-
sed, especially in the case of heavy pollution. By reducing
the volume of oil the effects of any explosion and subse-
quent fire are also reduced. Cemented flanges allow for
much higher work coefficients in porcelain than clamps and
enable excellent mechanical characteristics to be obtained
in spite of the small diameter.
Fig. 5. Transformador de intensidad servicio interior When ITs are installed at altitudes of more than 1000 m
Indoor current transformer
above sea level, it must be taken into account that the
lower air density makes it less electrically rigid, and taller
porcelain units are needed to withstand the same volta-
ges. Since the internal insulation is not affected by this
problem it does not need to be oversized. If the outside
insulation is to be checked in a laboratory at normal altitude
a reinforced prototype must be built so that higher voltages
can be applied. This is expensive: an alternative is to test the
flashover tension of the insulator, since this is not affected
appreciably when the internal parts are fitted.
Las aletas suelen ser todas iguales o alternadas (fig. 8) con Fig. 7. Transformador de intensidad servicio exterior,
lneas de fuga de 2 cm/kV para contaminacin media y 3,1 resina + porcelana
para muy fuerte. La norma CEI 815 desarrolla en profundi- Outdoor, epoxy+porcelain, current transformer
dad este tema.
4
Unin
Union
Fig. 9. Porcelana pegada Fig. 10. T. I. tipo horquilla Fig. 11. T. I. tipo aguja Fig. 12. T. I. tipo intermedio
Bonded porcelain Hair pin type C.T. Needle type C.T. Intermediate type C.T.
Cuando los TM se instalan en zonas muy altas, p.e. supe- 2.2 Internal Insulation
rior a 1.000 m sobre el nivel del mar, es necesario tener en
cuenta que la menor densidad del aire disminuye su rigidez, A. Main Insulating Element
y como consecuencia hay que aumentar la altura de la por-
celana para que soporte las mismas tensiones. Como el This comprises the oil paper insulating assembly between
aislamiento interno no se ve afectado por este fenmeno, the high and low voltage electrodes or screens.
no es preciso sobredimensionarlo, pero en el caso de que-
rer verificar el aislamiento externo en un laboratorio situado In CTs this insulation can be on the primary, on the
a una altura normal hay que construir un prototipo reforza- secondary or partly on each. If it is on the primary it may
do para poder aplicar tensiones superiores correspondien- be hairpin type (fig. 10) with the primary having the appe-
tes. arance of an insulated cable, or needle type (fig. 11).
These are usually known as dead tank models, with
Como esta solucin es cara, otra alternativa es ensayar la those having the insulation on the secondary (fig. 1)
tensin de contorneo del aislador, ya que su comporta- being known as live tank models. Models with insula-
miento en este aspecto no se ve afectado sensiblemente tion shared between primary and secondary are seldom
al colocar los elementos internos. used (fig. 12).
2.2 Aislamiento interno Cascade type CTs (fig. 13) are a special case. Two CTs of
one of the types indicated above are connected in series,
A. Elemento aislante principal with each bearing half the voltage. This voltage sharing is
a function of the capacities of the transformers (500-
Est formado por el conjunto aislante papel-aceite situado 1000 pF) and may vary due to strays or leakage current
entre los electrodos o pantallas de alta y baja tensin. if there is heavy pollution.
En los TI este aislamiento puede situarse sobre el primario, Kraft and/or capacitor type paper is used. It is overlap-
sobre el secundario o parcialmente en cada uno de ellos. ped so that no easy paths are provided for electric arcs.
En el primer caso, a su vez, puede tratarse del tipo horqui- There should be no gaps, because after impregnation
lla (fig. 10) donde el primario tiene aspecto de cable aisla- they will contain only oil, with a dielectric constant which
do, y tipo aguja (fig. 11). Es usual denominar a estos mode- is half that of oil paper. This will lead to a big increase in
los, tipo "cuba a tierra" a diferencia de los que tienen el gradient in an area which is already electrically weak.
aislamiento sobre el secundario (fig. 1) llamados tipo
"cuba activa". Los modelos con aislamiento repartido entre MVTs can be made up of a single coil (fig. 2) or several coils
el primario y secundario son poco utilizados (fig. 12). on a single core (fig. 14) or on several cores (fig. 15).
5
Los transformadores tipo cascada en TI (fig. 13) constituyen
un caso especial. En base a uno de los tipos citados se
colocan en serie dos TI, soportando cada uno la mitad de
la tensin. Este reparto de tensiones es funcin de las
capacidades de los transformadores (500 a 1000 pF) y
puede variar debido a las capacidades parsitas o corrien-
tes de fuga en caso de fuerte polucin.
6
manera que el reparto de tensiones capacitivo e inducti- In CVTs insulation comprises flat capacitor units connec-
vo se mantiene a diferentes frecuencias. Adems, como ted in series, fitted inside the porcelain. Each unit is made
la distancia entre capas de hilo es reducida, los gradien- by winding two sheets of aluminium and various sheets of
tes de trabajo del aislante son muy superiores a los utili- paper on a cylindrical mandrel and then impregnating
zados en los TI, llegando incluso a la mitad los utilizados them with mineral oil (fig. 17). Polypropylene is also used
en los TTC. with a sheet of paper to improve the impregnation of the
whole assembly. With polypropylene the value of tg ! of
En los TTC el aislamiento est formado por unidades con-
the capacitor is reduced considerably. However, bearing in
densadoras planas (galletas) conectadas en serie colo-
cadas dentro de la porcelana. Cada galleta se fabrica mind that MTs age due to partial discharges and not ther-
arrollando sobre un mandril cilndrico dos lminas de alu- mal effects, the significance of the value of tg ! is relati-
minio y diversas lminas de papel que posteriormente se ve and is only comparable when the same materials are
impregnan con aceite mineral (fig. 17). Tambin se utili- used.
za polipropileno, con una lmina de papel para mejorar la
impregnacin del conjunto. Con el polipropileno el valor B. Transitional Area
de la tg ! del condensador se reduce notablemente. No
obstante, teniendo en cuenta que el envejecimiento de This is the gap between the high and low voltage elec-
los TM se produce por efecto de las descargas parciales trodes along the sur face of the main insulator in contact
y no por efecto trmico, el valor de tg ! tiene un signifi- with the oil. If this area is properly designed the flasho-
cado relativo, y solamente comparable cuando se utilizan ver voltage can be raised both inside the MT and in the
los mismos materiales. air.
Deflector aislado
Insulated screen
Bobina de A.T.
High voltage coil
Bobina de B.T.
Low voltage coil
Fig. 15. T. T. cascada Fig. 16. Bobina de T. T. Fig. 17. Paquete condensador
Cascade M.V.T. M.V.T. coil Capacitor stack
7
a) b)
c) d)
a) Colchn de Nitrgeno / Nitrogen cushion
b) Baln de gas / Gas balloon
c) Membrana de goma / Rubber membrane
d) Fuelle metlico / Metal bellows
Fig. 18. Deflectores Fig. 19. Pantallas condensadoras Fig. 20. Compensadores
Rounded screens Capacitor screens Compensators
Aunque es un elemento auxiliar en el TM, influye de mane- At present, all ITs are built with an oil volume compensator
ra decisiva en el comportamiento en servicio del sistema so that the oil is not in direct contact with the air. This main-
aislante. tains the high dielectric characteristics of the oil paper
assembly, obtained by careful manufacturing with vacuum
Antiguamente, los TM, como otros aparatos elctricos, drying at more than 0.02 Torr. for 5-15 days. In final elec-
tenan el aceite en contacto con la atmsfera por lo que trical testing these ITs have not partial discharges, and their
estaban saturados de gas y agua. En ciertos casos se uti- tg ! is lower than 0.5%.
lizaba un filtro de secado con silicagel, pero al estar situa-
do en la zona de alta tensin, en la prctica no se cam- There are many versions of compensator designs, but
biaban y al cabo de poco tiempo este dispositivo no era most are covered by the four shown in fig. 20.
efectivo. Este diseo es vlido hasta cierta tensin siem-
pre que se dimensione suficientemente el aislamiento, A. Nitrogen Cushion
pero en el caso de muy alta tensin, p.e. 420 kV, el valor
elevado de la tg ! de este aislamiento produce un calen- The oil is saturated with gas. The amount it contains is a func-
tamiento importante, que en un TI con gran espesor de tion of pressure and temperature. At low temperatures the
aislamiento y difcil refrigeracin provoca el envejeci- reduction in pressure causes bubbles to form in the oil. These
miento prematuro del transformador. rise to the top chamber, leading to partial discharges.
8
Actualmente todos los TM, se construyen con un compen- Experiments have shown that in gas saturated oil with pres-
sador del volumen de aceite de manera que ste no est sures of less than 0.8 bar absolute, the voltage at which par-
en contacto con el aire. As se mantienen las elevadas tial discharges appear drops drastically (fig. 21). To prevent
caractersticas dielctricas del conjunto papel-aceite obte- this, transformers are usually built with a slight overpressu-
nidas en una cuidada fabricacin mediante secado con re at ambient temperature (20oC). However the leak-tight-
vaco superiores a 0,02 Torr, durante un perodo de 5 a 15 ness of the seals must be ensured to prevent that over-
das. En los ensayos elctricos finales, estos TM resultan pressure from causing gas leaks under maximun heating
exentos de descargas parciales (DP) y con valores de tg ! conditions.
inferiores a 0,5%.
Another hazard of this design is the possibility that water
Aunque existen muchas variantes en el diseo del com- lying on the surface of the transformer in contact with the
pensador, se pueden resumir en 4 indicadas en la fig. 20. seal area may get inside if the seals do not work properly,
because at low temperatures there will be underpressure.
A. Colchn de nitrgeno
El aceite est saturado de gas, siendo la cantidad que B. Gas Balloon
contiene funcin de la presin y temperatura. Por ello, a
bajas temperaturas la disminucin de la presin provoca This is an improved variant of the above. The gas is not in
la formacin de burbujas en el seno del aceite, que van contact with the oil and the oil is therefore not saturated.
ascendiendo hacia la cmara superior. La consecuencia
elctrica de este fenmeno es la aparicin de DP. Oil pressure also varies with temperature here, with the
consequent risks should the seals fail.
Se ha comprobado experimentalmente que en aceite satu-
rado de gas, a presiones inferiores a 0,8 bares absolutos, C. Rubber Membrane
la tensin de aparicin de DP disminuye drsticamente (fig.
21). Para evitar este fenmeno, es usual que el transfor- In this case the oil pressure is constant due to the great
mador se construya con una ligera sobrepresin a tempe- elasticity of the membrane. If the correct material is used
ratura ambiente (20oC) pero hay que garantizar la calidad de the permeability of the compensator can be reduced and oil
las juntas para evitar que la sobrepresin en el caso de kept in good condition for years.
mximo calentamiento produzca fuga de gas.
D. Metal Bellows
Otro peligro de este diseo, es la posible entrada del
agua alojada en la superficie del transformador en con- This solution is similar to the previous one, but metal (e.g.
tacto con la zona de juntas, cuando stas no funcionan stainless steel) is used as the elastic element.
correctamente, ya que a bajas temperaturas se producir
una subpresin. If the compensator is built of welded plates the whole
B. Baln de gas assembly is highly elastic and no pressure is produced in
the oil when the volume varies. The welding is highly deli-
Constituye una variante mejorada del caso anterior, ya que cate and requires great care, because the steel involved is
el gas no est en contacto con el aceite y por lo tanto ste very thin.
no est saturado.
La presin del aceite vara tambin con la temperatura, U(KV)
con el consiguiente peligro en caso de fallo de juntas de 1. Sin N2 en contacto con
aceite (casos b, c y d)
estanqueidad.
1. Without N2 in contact
with oil (cases b, c, d)
C. Membrana de goma 1
2. Con cmara de N2 (caso a)
En este caso la presin del aceite es constante, debido
2. With N2 chamber (case a)
a la gran elasticidad de la membrana. 2
9
Si el compensador est formado por platos soldados, el
conjunto resulta muy elstico y no se produce presin en
el aceite al variar de volumen. La soldadura es muy delica-
da debido al reducido espesor del acero y debe controlarse
cuidadosamente.
3. NUEVOS AISLANTES
Un inconveniente de este aislante es que as como en las Fig. 22. T. I. aislado con gas SF6
subestaciones blindadas se realiza un control riguroso de la SF6 insulated C.T.
presin del gas, desconectando el sistema cuando sta baja,
en los TM resulta complicado utilizar mtodos similares.
In the case of bellows made by shaping (no welds in the
Los TT de las subestaciones blindadas se fabrican, gene- main body) pressure must be applied to make then chan-
ralmente aislados tambin con SF6, como se ve en la ge volume, which means that the oil does not work at
figura 23. El aislamiento entre capas puede ser papel constant pressure. On the other hand, compensators of
pero es necesario asegurar su correcto secado, ya que la this type can deteriorate if sudden changes of volume
presencia de humedad en atmsfera de SF6 y arcos elc- occur at low temperatures.
tricos produce compuestos corrosivos. Por esta razn es
habitual utilizar polipropileno como aislante, ya que no es 3. NEW INSULATING MATERIALS
higroscpico.
CT using SF6 gas as their main insulator have existed for
Como aislamiento externo, se han comenzado a utilizar many years, but new versions have recently come onto the
tubos de fibra de vidrio y resina con aletas de silicona. market.
Este diseo es menos frgil que la porcelana, pero de
momento la experiencia que existe no es grande, y es Fig. 22 shows a construction of this type, where oil paper
necesario garantizar la calidad de la zona de unin entre insulation and supplementary oil have been replaced by
las aletas y el tubo. SF6, resulting in a simple assembly. The design varies
10
Caso aparte, constituyen los TM electrnicos, en los que la slightly in other cases, e.g. an insulating support may be
conexin entre el lado de alta tensin y el de baja tensin placed between the primary and secondary to improve
puede ser algo tan simple como una fibra ptica. mechanical characteristics, or an intermediate screen may
be used to optimize the distribution of the field along the
4. CONTROL DE CALIDAD Y ENSAYOS insulator.
Existen normas sobre transformadores de medida (CEI This material is well known due to its use in GIS (gas insu-
60044-1, 60044-2, IEEE C57-13 etc.) en las que se indi- lated substation) substations. It usually runs at 3.5 - 4.5
can diversos ensayos de tipo y de rutina, en base a los bar absolute, since its dielectric characteristics improve
cules puede establecerse en cierto modo la calidad de considerably with increased pressure, but care must be
los aparatos. taken to prevent condensation from forming at low tempe-
ratures. This is important in ITs because they are installed
Sin embargo es necesario completar estos medios de con- outdoors, where they may have to contend with temperatu-
trol con otros que garanticen de la mejor manera posible res of - 25oC or even lower.
la calidad total de la fabricacin. La norma ISO 9000 sobre
Sistemas de Calidad establece, en funcin del nivel elegi- One problem with this insulation is that in ITs, it is highly
do, los procesos o aspectos a controlar en la fabricacin, complicated to use methods similar to those used in GIS
como son: Diseo, Documentos, Proveedores, Inspeccin substations, where gas pressure is checked carefully and
en Proceso, Registros, etc. the system is disconnected when the pressure is too low.
A continuacin comentaremos algunos ensayos finales The MVT in GIS substations are generally also insulated with
cuyas caractersticas estn en estudio, as como algunas SF6, as shown in fig. 23. The insulation between layers may
condiciones exigidas a los TM, pero no incluidas en nor- be paper, but if so proper drying must be ensured, as any
mas. moisture in an atmosphere of SF6 and electric arcs can pro-
duce corrosive compounds. For this reason polypropylene is
A. Ensayos dielctricos de rutina normally used as an insulator, as it does not absorb water.
Debido al esfuerzo que supone para el transformador, el As external isolation, tubes of fiber glass with silicone
ensayo de rigidez a frecuencia industrial, la tendencia es sheds have begun to be used. This design is less fragile
reducir su valor pero midiendo las DP a continuacin, sin than the porcelain, but there is not much experience of it,
bajar a cero la tensin. and it is necessary to guarantee the quality of the join bet-
ween sheds and tube.
11
En los TTC se est estudiando un ensayo de DP aplican- A. Routine Dielectric Testing
do ondas de maniobra superpuestas a la frecuencia
industrial. Since a rigidity test at industrial frequency puts a strain on
the transformer, there is a tendency to reduce the level but
B. Ensayos de vida measuring partial discharges immediately afterwards, wit-
hout reducing voltage to zero.
Como se ha indicado anteriormente en los TM no es normal
que se produzca un envejecimiento trmico. No obstante si B. Lifetime Testing
se estima conveniente puede aplicarse un ensayo de esta-
bilidad trmica. La medicin de tg ! despus de un ensayo As indicated above thermal aging does not usually take
de calentamiento no es suficiente para conocer este fen- place in ITs. However, if it is considered convenient a ther-
meno. mal stability test can be performed. Measuring tg ! after a
heating test is not sufficient to check this phenomenon.
El envejecimiento elctrico se produce por las DP, y por
ello, el ensayo acelerado debe basarse en las curvas ten- Electrical aging is caused by partial discharges, so accele-
sin-tiempo, de igual probabilidad a DP. Estas curvas son rated testing must be based on voltage/time curves with
de la forma the same probability of partial discharges. These curves
U=Ct -! have the following form:
-!
U=Ct
donde C y ! son constantes.
where C and ! are constants.
C. Transitorios de alta frecuencia
C. High-frequency Transients
Durante las maniobras de interruptores o seccionadores,
se producen oscilaciones de alta frecuencia (0,1 a 10 M When disconnectors or circuit breakers are used, high-fre-
Hz) con tensiones hasta 3 veces la nominal. Este tipo de quency oscillations (0.1 -10 MHz) are produced with volta-
ondas produce corrientes de corta duracin en las panta- ges up to 3 times the rated level. Waves of this type cause
llas de los TM de hasta 500 A provocando, a veces, el fallo short-duration currents in TM screens of up to 1000 A,
del transformador. sometimes causing the transformer to fail.
Para analizar el comportamiento de los TM ante este fen- To analyze the behaviour of ITs in respect of this pheno-
meno, la norma CEI expone un mtodo, que consiste en menom, IEC has a method in which at least 100 pulses
aplicar al menos 100 impulsos cortados en la cresta y ana- chopped at the crest are applied, and the comparision
lizar la evolucin de los gases disueltos. with the values of gas content before and after test is
analyzed.
Los incrementos de gases disueltos en el aceite estn en
discusin en los grupos de trabajo CEI. The increases in gases dissolved in the oil are being dis-
cussed in the CEI working groups
Cuando se produce la apertura de una lnea en vaco, la When a line is opened under no load, maximum voltage is
tensin es mxima y si no se descarga puede producirse obtained. If this is not discharged there may be an overvol-
una sobretensin en el reenganche. tage on reconnection.
Los TT son aparatos adecuados para descargar las lneas, MVTs are suitable for discharging lines, since their impe-
ya que su impedancia se reduce rpidamente al saturarse dance drops rapidly when the core is saturated with the
el ncleo con la corriente transitoria. No obstante, esta transient current. However, this high current causes ther-
elevada corriente produce esfuerzos trmicos y dinmicos mal and dynamic stresses in the winding, and can even
en el bobinado, llegando incluso a destruir el transforma- destroy the transformer if it is not prepared to support
dor si no est preparado para soportarlas. them.
Un caso similar se produce en los TT destinados a des- The same thing can happen to MVTs used to discharge
cargar bancos de condensadores. banks of capacitors.
12
E. Ferrorresonancia E. Ferro-resonance
Aunque este fenmeno no se produce con mucha fre- This phenomenom is not frequent, but it is highly dange-
cuencia, resulta muy peligroso ya que, generalmente, el rous, as the MVT is generally destroyed by overheating.
TT se destruye por calentamiento.
De acuerdo con las caractersticas del circuito, la ferro- Depending on the characteristics of the circuit, ferro-reso-
rresonancia puede ser serie o paralelo, pero esta ltima nance may be in series or parallel, though the latter only
slo aparece en lneas con neutro aislado, por lo que no occurs in lines with an insulated neutral and is therefore
es propia de la alta tensin. not found in high voltage situations.
En cuanto a la ferrorresonancia serie, adems del conoci- Apart from the well known case of CVT, ferro-resonance
do caso de los TTC, puede encontrarse en TT conectados in series can also be found in MVTs connected to a volta-
a una lnea en tensin a travs de los condensadores de ge line through distributing capacitors of a circuit breaker
reparto de un interruptor o a travs de la capacidad entre or through the capacity between lines when one is live and
lneas cuando una est en tensin y la otra no. the other is not.
Existen mtodos para suprimir este fenmeno como la uti- There are ways of avoiding this phenomenom, such as the
lizacin de un secundario auxiliar, conectado en tringulo use of an auxiliary secondary in an open delta connection
abierto sobre una resistencia. on a resistor.
El nmero de roturas que se producen en el transporte o The number of breakages in loading, transit and unloading
en la carga y descarga es importante. Adems, puede is important. Malfunctions may also be caused which are
producirse una avera no detectada que produce el fallo not detected and which cause the transformer to fail when
del transformador al poner en servicio. it is put into service.
Se ha comprobado, que el transporte en camin o ferro- It has been shown that truck and rail transportation is har-
carril es ms severo que en barco, y se han alcanzado der on equipment than sea transportation, with levels of
valores incluso superiores a 10 g. 10 g or even more being reached.
Por todo ello, se ve la necesidad de establecer valores It is therefore necessary to set maximum acceleration
mximos de manera que por un lado se diseen los emba- levels in accordance with which packaging can be desig-
lajes de forma que soporten estos valores y por otro se ned and which should not be exceeded during transporta-
garantice que el transporte no supera dichas aceleracio- tion. There are indicators available which can be built into
nes. Existen dispositivos indicadores, que podran incorpo- packaging to check this.
rarse en los embalajes para verificar este dato.
Otro fenmeno que puede destruir mecnicamente un TM ITs can also be mechanically destroyed by earthquakes,
es el terremoto. Los TM son aparatos esbeltos y frgiles, y since they are slim, fragile units. It must be taken into
deben calcularse adecuadamente si el lugar de instalacin account whether the installation site is likely to suffer
es propenso a sesmos. earth tremors.
Las especificaciones de diversas Compaas, establecen Various companies have drawn up specifications which
adecuadamente los criterios de diseo, as como los include design criteria and checking tests, and experience
ensayos de verificacin, y la experiencia ha demostrado has shown that ITs manufactured to their requirements
que TM fabricados de esta manera se han comportado can withstand heavy earthquakes
correctamente durante importantes terremotos.
En algunos casos, especialmente en muy alta tensin, In some cases, especially with very high voltages, shock
puede ser necesario utilizar amortiguadores. absorbers may need to be used.
13
Mediante el anlisis de gases disueltos en el aceite se By analyzing the gases dissolved in the oil the condition of
puede conocer el estado del transformador y las causas the transformer can be learned, along with the causes of
del deterioro. Normalmente se mide H2, CH4, C2H4 y any deterioration. Normally H2, CH4, C2H4 and C2H2 are
C2H2, pero en los TM los ms interesantes son el H2 que measured, though in ITs the most important are H2 (which
indica presencia de descargas parciales de pequea indicates the presence of low energy partial discharges)
energa y el C2H2 que indica descargas elctricas ms and C2H2 (which indicates larger electrical discharges).
importantes.
Este mtodo se ha utilizado mucho en transformadores This method is widely used in power transformers, but it
de potencia, pero en TM se ha comprobado que no pue- has been shown that the same criteria cannot be used for
den utilizarse los mismos criterios, ya que los resultados ITs, as the results depend largely on the type of construc-
dependen mucho del tipo de construccin. Actualmente tion. Research is being carried out into this matter, and it
se est investigando este tema y es de esperar que en is hoped that the phenomenom will be better known within
pocos aos se conozca mejor el fenmeno. a few years.
A ttulo orientativo, se indican los valores lmite de gases As a guideline, the limit levels for dissolved gases in ITs
disueltos en TM en la Norma IEC 60599 are indicated in the IEC 60599 standard.
Se estn realizando experiencias para facilitar este ensa- Experiments are being carried out to facilitate this test by
yo colocando detectores en los TM, e incluso se estudia placing detectors inside ITs, and the possibility of conti-
la posibilidad de un control en continuo. La razn es que nuous monitoring is also being studied. The reason
en un TM de muchos aos en servicio, puede producirse behind this is that ITs which have been in service for many
un envejecimiento muy rpido si aparecen DP. years can age very quickly if partial discharges appear.
El valor tg ! a 90oC del aceite es un indicativo de su con- The tg ! level of oil at 90oC indicates the degree of conta-
taminacin pero resulta difcil relacionarlo con el estado mination, but is hard to relate this to the condition of the
del aislamiento principal. Con valores superiores al 6% main insulation. With levels of more than approx. 6% the
aproximadamente puede estimarse que el aceite no est oil can be assumed to be in poor condition.
en buen estado.
La medida del contenido de agua en el aceite es impor- It is also important to measure the amount of water in the
tante, ya que el agua pasa del aceite al papel deterioran- oil, as water passes from the oil to the paper, thus dete-
do el aislamiento principal. De esta manera, aunque no riorating the main insulation. By analyzing the oil in this
ensayemos a tg ! todo el transformador, podemos esti- way we can, even without testing the whole transformer at
mar si se ha humedecido gracias al anlisis del aceite. tg !, estimate whether it has become wet.
La medida de fur furaldehido en el aceite para detectar el Furfuraldehide in oil is measured to detect aging due to
envejecimiento debido a fenmenos que no producen phenomena other than arcs. Though this is one of the
arcos, aunque es uno de los parmetros utilizados en parameters used in power transformers, it is not signifi-
transformadores de potencia, no es significativa en TM. cant in ITs.
Los ensayos de tg ! y DP del transformador, son un com- Partial discharge and tg ! tests on transformers area a
plemento adecuado para conocer el estado del aisla- suitable additional means of learning the condition of the
miento, pero en general, solamente puede realizarse en insulation, but in general they can only be performed in a
un laboratorio. laboratory.
Hay equipos por ttiles para medir tg ! a 10 kV, pero es There are portable units for measuring tg ! at 10 kV, but
un ensayo complicado porque hay que desconectar el the test is complicated becaused the ITs has to be dis-
TM de la lnea y limpiar el aislador ya que esta medida connected from the line and the insulator cleaned. The
vara mucho si no se realiza con cuidado. Para este measurements can vary greatly if this is not done care-
ensayo en TI, en conveniente que exista una toma ais- fully. On CTs it is advisable for an insulated connection
lada. point to be used for this test.
15
D. Otros mtodos D. Other methods
Mediante equipos de termovisin pueden detectarse defec- Thermovision equipment can be used to detect defects in
tos en conexiones primarias de TI, calentamiento excesivo the primary connections of CTs, excessive heating in CVTs,
en TTC, etc. Es un mtodo sencillo y muy sensible y las etc. This is a simple, highly sensitive method which is
experiencias recomiendan su utilizacin. recommended by experience.
Para detectar fallos de galletas en TTC se puede utilizar la To detect failures in condenser units of CVTs, open delta
tensin en tringulo abierto, ya que el fallo del condensa- voltage can be used, as capacitor failures normally occur
dor se produce normalmente de forma gradual. gradually.
Se han realizado tambin experiencias con mtodos ultra- Ultrasonic methods have also been tried to detect internal
snicos, para detectar descargas internas, pero de discharges, but for the moment the sensitivity levels attai-
momento no se ha logrado suficiente sensibilidad. ned are not sufficient.
6. CONCLUSIONES 6. CONCLUSIONS
El aislamiento clsico papel-aceite sigue siendo el normal- The classical oil paper insulation system is still normally
mente utilizado en los TM. Mejoras en la calidad de los used in ITs. Improvements in material quality and design
materiales y en los diseos, han permitido elevar notable- have enabled dielectric characteristics to be considerably
mente sus caractersticas dielctricas. improved.
Se estn utilizando nuevos materiales, especialmente gas New materials are being used, especially SF6 gas in ITs
SF6 en los TM para subestaciones blindadas y por exten- for GIS substations and by extension in normal uses.
sin en los normales.
The tests laid down in standards are considered insuffi-
Los ensayos citados en las normas, se estiman insufi- cient, and need to be supplemented to ensure correct
cientes y se precisa complementarlos para garantizar el transformer operation in service.
correcto funcionamiento del transformador en servicio.
Various ways exist of learning the condition of the insulation
Aunque existen diversos mtodos para conocer el estado de of a IT which has been in service for many years, though
aislamiento en TM con muchos aos en servicio, de momen- for the moment none is considered to be sufficiently relia-
to no se ha obtenido uno suficientemente fiable y sencillo. ble and simple.
Toma de Tg !
Capacitance
and tg ! TAP.
Fig. 26.
16
5. INSPECCIN Y CONTROL EN CAMPO 5. INSPECTION & CHECKING IN THE FIELD
Finalmente, al aplicar tensin, cualquier ruido extrao Finally, any unusual noise on powering up may be a sign
puede ser un indicativo del mal funcionamiento del trans- of transformer malfunction.
formador.
5.2 Control en Campo
A. Inspeccin visual
Es aconsejable un control visual de los transformadores de
forma peridica, p.e. trimestralmente, inspeccionando los
indicadores de nivel, etc., as como posibles fugas de acei-
te. Tambin como en el caso anterior, conviene verificar si
hay algn ruido extrao.
A. Visual inspection
B. Oil analysis
14