Académique Documents
Professionnel Documents
Culture Documents
KDC-BT265U KMR-D365BT
KDC-X300
CD-RECEIVER
INSTRUCTION MANUAL
AMPLI-TUNER LECTEUR DE CD
MODE DEMPLOI
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM
MANUAL DE INSTRUCCIONES
US Residents Only
Register Online
Register your Kenwood product at www.Kenwoodusa.com
2015 JVC KENWOOD Corporation B5A-0878-10 (KN)
Note de IC (Industrie Canada) Under Industry Canada regulations, this radio transmitter may only operate using an
Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry
radio exempts de licence. Canada. To reduce potential radio interference to other users, the antenna type and its gain
Lexploitation est autorise aux deux conditions suivantes: should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more
(1) lappareil ne doit pas produire de brouillage, et than that necessary for successful communication.
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le
brouillage est susceptible den compromettre le fonctionnement. ATTENTION
Lexpression IC: avant le numro dhomologation/ enregistrement signifie seulement Cet quipement est conforme aux limites dexposition aux rayonnements nonces
que les specifications techniques dIndustrie Canada ont t respectes. pour un environnement non contrl et respecte les rgles dexposition aux frquences
radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui
est considre conforme sans valuation de lexposition maximale autorise. Cependant,
Para cumplimiento de la COFETEL: cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre
La operacin de este equipo est sujeta a las siguientes dos condiciones: le dispositif rayonnant et le corps ( lexception des extrmits : mains, poignets, pieds et
(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y chevilles).
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda
causar su operacin no deseada Conformment la rglementation dIndustrie Canada, le prsent metteur radio peut
fonctionner avec une antenne dun type et dun gain maximal (ou infrieur) approuv
Contains Bluetooth Module FCC ID: ZWY8811X pour lmetteur par Industrie Canada. Dans le but de rduire les risques de brouillage
IC ID: 12033A-8811X radiolectrique lintention des autres utilisateurs, il faut choisir le type dantenne et son
gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas
lintensit ncessaire ltablissement dune communication satisfaisante.
ii
iii
Article 10 Protection of Copyright The above copyright notice and this permission notice shall be included in all copies
1. The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the or substantial portions of the Software.
Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User.
2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
intellectual property rights. IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
Article 11 Export Restriction OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
1. It is prohibited to export the Licensed Software and any related documents outside the country of the User ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
(including transmission thereof outside the country of the User via Internet of other communication tools). OTHER DEALINGS IN THE SOFTWARE.
2. The User shall understand that the Licensed Software shall be subject to the export restrictions adopted by the
country of User and any other countries.
3. The User shall agree that the software will be subject to any and all applicable international and domestic laws
(including the export control regulation of the country of User and any other countries, and any restrictions
concerning the end-users, the use by end-users and importing countries to be provided by the country of User and
any other countries, and any other governmental authorities).
Article 12 Miscellaneous
1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions shall continue in
force.
2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of this Agreement
shall be provided or settled upon good-faith consultation between the Licensor and the User.
3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and any dispute
arising from, and relating to the rights and obligations under, this Agreement shall be submitted to the exclusive
jurisdiction of the Tokyo District Court for its first instance.
iv
/
/ Pull out the
: insulation sheet
Lights up when when using for
Bluetooth the first time.
connection is
established.
( 15) : Can be remotely controlled with an
optionally purchased remote control.
Detach button / / : : Remote control functions are not
Flashes when the unit enters searching status. available.
Attach Detach How to reset How to replace the battery
Press the switch twice
within 5seconds after
detaching the faceplate.
ENGLISH 5
ENGLISH 7
ENGLISH 9
Preparation:
Direct Music Search (using RC-406)
Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then
1 Press DIRECT. create an account and log in to Pandora.
2 Press the number buttons to enter a track/file Select [ON] for [PANDORA SRC]. ( 5)
number.
3 Press to search for music. Start listening
To cancel, press or DIRECT. 1 Open the Pandora application on your device.
Not available if Random Play is selected. 2 Connect your device to the USB input terminal.
Not applicable for iPod and ANDROID.
USB input terminal
Other settings
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select an item (see KCA-iP102 / KCA-iP103 (optional accessory)*1 or
the following table), then press the knob. accessory cable of the iPod/iPhone*2
3 Repeat step 2 until the desired item is selected
or activated. 3 Press repeatedly to select PANDORA.
4 Press and hold to exit. Broadcast starts automatically.
To return to the previous setting item, press .
To On the faceplate On the remote control
Default: XX Playback / pause Press . Press .
USB Skip a track Press T. Press .
MUSIC DRIVE DRIVE CHANGE:The next drive ([DRIVE 1] Thumbs up or thumbs down*3 Press J/K. Press / .
to [DRIVE 4]) is selected automatically and
playback starts. *1 KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
Repeat steps 1 to 3 to select the following *2 Do not leave the cable inside the car when not using.
drives. *3 If thumbs down is selected, the current track is skipped.
SKIP SEARCH 0.5%/ 1%/ 5%/ 10%: While listening to iPod Create and save a new station
or ANDROID, selects the skip search ratio over 1 Press .
the total files. 2 Turn the volume knob to select [NEW STATION], then press the knob.
3 Turn the volume knob to select [FROM TRACK] or [FROM ARTIST], then press the knob.
A new station is created based on the current song or artist.
4 Press and hold one of the number buttons (1to5) to store.
To select a stored station, press one of the number buttons (1to5).
10
Preparation:
Search for a registered station
Install the latest version of iHeartAuto application on your device (iPhone/ iPod
1 Press . touch), then create an account and log in to iHeartRadio.
2 Turn the volume knob to select an item, then press the knob. Select [ON] for [IHEART SRC]. ( 5)
[SORT BY DATE]:According to the registered date
[SORT BY A-Z]:Alphabetical order Start listening
3 Turn the volume knob to select the desired station, then press 1 Open the iHeartAuto application on your device.
the knob. 2 Connect your device to the USB input terminal.
To cancel, press and hold .
(or using RC-406) USB input terminal
Press J / K to search for a station, then press .
ENGLISH 11
Only SiriusXM brings you more of what you love to listen to, all in one place. Get over 140
Search and store a station
channels, including commercial-free music plus the best sports, news, talk, comedy and
1 Press . entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription
2 Turn the volume knob to select a category, are required. For more information, visit www.siriusxm.com.
then press the knob.
3 Turn the volume knob to select the desired Preparation:
station, then press the knob. 1 Connect the optional SiriusXM Vehicle Tuner (commercially available).
When a city list appears, you can search cities
in alphabetical order by turning the volume Antenna
knob quickly.
To cancel, press and hold .
Start listening
1 Press repeatedly to select SIRIUSXM.
2 Press repeatedly to select a band.
3 Press .
lights up.
4 Turn the volume knob to select a category, then press the knob.
If ALL CHANNELS is selected, all the available channels will be shown.
12
5 Turn the volume knob to select a channel, then press the knob. When replay keymode is selected...
(or)
To On the faceplate
Press S / T to search for a channel manually.
Pressing and holding S / T changes the channel rapidly. Playback / pause Press .
If a locked channel or a mature channel is selected, a pass code input Select a track Press S/T.
screen appears. Enter the pass code to receive the channel. ( 14) Rewind / Fast-forward Press and hold S/T.
Go to Live Press 1.
To change the tuning method for S/T: Press .
Each time you press , the tuning method switches between
CHANNEL (manually search for a channel) and PRESET (searches for a
preset channel of the selected band). SmartFavorites and TuneStart
User stored channels are recognized as SmartFavorite channels*. The
SiriusXM Vehicle Tuner automatically buffers the broadcast content in the
SiriusXM Keymode background.
Press and hold to change the keymode (channel or replay). SmartFavorites feature is available with SXV200 or later SiriusXM
(Default: Channel keymode) Vehicle Tuner.
lights up when replay keymode is selected. * SXV300 (and later) SiriusXM Vehicle Tuner can use all 18 stored channels as SmartFavorites.
The SXV200 SiriusXM Vehicle Tuner can use 6 stored channels from the current band as
When channel keymode is selected... SmartFavoites.
To On the faceplate When you select a SmartFavorite channel, you can rewind and replay up
to 30minutes of any of the missed news, talk, sports or music content.
Select a channel Press S/T. Playback starts from the beginning of the song if [TUNE START] is set to
Change a channel Press and hold S/T. [ON] ( 14) for most music channels stored as a SmartFavorite.
rapidly Press one of the number buttons (1 to 6) to select a stored channel.
Store a channel of the Press and hold one of the number buttons
current band (1to6).
Select a stored channel Press one of the number buttons (1to6).
of the current band
ENGLISH 13
Default: XX
TuneScan
You can get a short preview of the songs that you have missed CHANNEL LOCK To unlock settings:
on each of your SmartFavorite music channels or currently 1 Turn the volume knob to select a number.
tuned music channel. 2 Press S / T to move to the entry position.
3 Repeat steps 1 and 2 to enter the current pass code.
Press and hold to start scanning the first 6 seconds
(Initial pass code is 0000.)
of the recorded music contents.
4 Press the volume knob to confirm.
To listen to the current song, press the volume knob to stop
scanning. The unit continues playing the current song. CODE SET 1 Turn the volume knob to select a number.
To select the previous/next song, press S/T. 2 Press S / T to move to the entry position.
To cancel scanning, press and hold the volume knob. 3 Repeat steps 1 and 2 to enter a new 4-digit pass code.
Playback returns to the channel before you entered 4 Press the volume knob to confirm.
TuneScan. 5 Repeat steps 1 to 4 to reconfirm the pass code.
Make a note of the new pass code to enter channel lock settings for next time.
SiriusXM settings LOCK SETTING MATURE CH:Selects the SiriusXM-defined lock setting.; USER DEFINED:Selects
the individual channels the user wants to lock.; OFF:Cancels.
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select [SIRIUS XM], then press the CHANNEL EDIT*1 1 Turn the volume knob to select a category, then press the knob.
knob. 2 Turn the volume knob to select a channel you want to lock, then press the
3 Turn the volume knob to select an item (see the following knob.
table), then press the knob. L appears in front of the channel number.
4 Repeat step 3 until the desired item is selected/activated 3 Press and hold to exit.
or follow the instructions stated on the selected item. CHANNEL CLEAR*1 YES:Clears all the locked channels.; NO:Cancels.
5 Press and hold to exit.
TUNE START*2 ON:All qualified music channels in the SmartFavorite will start playback from the
To return to the previous setting item, press . beginning of the song.; OFF:Cancels.
SIGNAL LEVEL NO SIGNAL/ WEAK/ GOOD/ STRONG:Shows the strength of the current received
signal.
BUFFER USAGE 0%100%(0):Shows the memory usage for Replay buffer.
SXM RESET YES:Resets stored channel and lock setting to default.; NO:Cancels.
*1 Displayed only when [USER DEFINED] is selected.
*2 Available only if the connected SiriusXM Vehicle Tuner is SXV200 or later that supports SmartFavorites.
14
Auto Pairing
When you connect iPhone/ iPod touch/ Android device to the USB input terminal, pairing request
(via Bluetooth) is automatically activated.
Adjust the Press the volume knob to pair once you have confirmed the device name.
microphone angle
Secure using cord clamps (not Automatic pairing request is activated only if:
supplied) if necessary. Bluetooth function of the connected devcie is turned on.
[AUTO PAIRING] is set to [ON]. ( 19)
* For , connect to the microphone input KENWOOD MUSIC PLAY application is installed on the Android device ( 8) and [BROWSE MODE] is
terminal. ( 31) selected ( 9).
ENGLISH 15
16
ENGLISH 17
PHONE BOOK (Applicable only if the phone supports PBAP) Make a call using voice recognition
1 Turn the volume knob quickly to enter alphabet search mode (if the 1 Press and hold to activate the voice recognition of the
phonebook contains many contacts). connected phone.
The first menu (ABCDEFGHIJK) appears. 2 Speak the name of the contact you want to call or the voice
To go to the other menu (LMNOPQRSTUV or WXYZ1 ), press J / K.
* command to control the phone functions.
To select the desired first letter, turn the volume knob or press Supported Voice Recognition features vary for each phone. Refer to
S / T, then press the knob. the instruction manual of the connected phone for details.
Select 1 to search with numbers and select to search with
* This unit also supports the intelligent personal assistant function of
symbols. iPhone.
2 Turn the volume knob to select a name, then press the knob.
3 Turn the volume knob to select a phone number, then press the knob to
call. Settings in memory
The phonebook of the connected phone is automatically transferred to the
Store a contact in memory
unit when pairing.
Contacts are categorized as: HOME, OFFICE, MOBILE, OTHER, GENERAL or You can store up to 6 contacts into the number buttons (1 to 6).
HM (home), OF (office), MO (mobile), OT (other), GE (general) 1 Press to enter Bluetooth mode.
This unit can display only non-accent letters. (Accent letters such as is 2 Turn the volume knob to select [CALL HISTORY], [PHONE BOOK], or
showns as U.) [NUMBER DIAL], then press the knob.
3 Turn the volume knob to select a contact or enter a phone
NUMBER DIAL 1 Turn the volume knob to select a number (0 to 9) or character ( , #, +). number.
2 Press S / T to move the entry position. If a contact is selected, press the volume knob to show the phone
Repeat steps 1 and 2 until you finish entering the phone number. number.
3 Press the volume knob to call. 4 Press and hold one of the number buttons (1 to 6).
(or using RC-406) STORED appears when the contact is stored.
1 Press the number buttons (0 to 9) to enter the phone number. To erase a contact from the preset memory, select [NUMBER DIAL] in
2 Press to call. step 2 and store a blank number.
VOICE Speak the name of the contact you want to call or the voice command to
control the phone functions. Make a call from memory
( Make a call using voice recognition) 1 Press to enter Bluetooth mode.
BATT LOW/ MID/ FULL*:Shows the strength of the battery. 2 Press one of the number buttons (1 to 6).
3 Press the volume knob to call.
NO SIGNAL/ LOW/ MID/ MAX*:Shows the strength of the current received signal. NO MEMORY appears if there is no contacts stored.
* Functionality depends on the type of the phone used.
18
ENGLISH 19
20
ENGLISH 21
22
General
3 Turn the volume knob to adjust the level (0 9), then press the Sound cannot be heard. Clean the connectors. ( 26)
knob. The unit does not turn on.
DIMMER Dim the display illumination (and button illumination*1). Information shown on the
ON:Dimmer is turned on.; OFF:Cancels. display is incorrect.
DIMMER TIME:Set the dimmer on and off time. The unit does not work at all. Reset the unit. ( 3)
1 Turn the volume knob to adjust the [ON] time, then press the knob.
2 Turn the volume knob to adjust the [OFF] time, then press the knob. (For ) Setting/deleting the remote control ID is unsuccessful.
(Default: [ON]: 6:00 PM; [OFF]: 6:00 AM) SET ERROR / DEL ERROR Turn the power off, then turn on the power and perform
the operation again. ( 5)
BRIGHTNESS (For / / )
1 Select a zone. ( 22) Radio reception is poor. Connect the antenna firmly.
Radio
2 0 31: Select your preferred brightness level for display Static noise while listening
illumination and button illumination. to the radio.
(For / ) Disc cannot be ejected. Press and hold M to forcibly eject the disc. Be careful not
0 31: Select your preferred brightness level for display illumination to drop the disc when it is ejected. If this does not solve
and button illumination. the problem, reset the unit. ( 3)
CD / USB / iPod
TEXT SCROLL AUTO/ ONCE:Select whether to scroll the display information Noise is generated. Skip to another track or change the disc.
automatically, or scroll only once.; OFF:Cancels. Tracks do not play back as you Playback order is determined when files are recorded.
*1 For / / . intended them to play.
*2 Preset colors: RED1/ RED2/ RED3/ PURPLE1/ PURPLE2/ PURPLE3/ PURPLE4/
READING keeps flashing. Do not use too many hierarchical levels or folders.
BLUE1/ BLUE2/ BLUE3/ SKYBLUE1/ SKYBLUE2/ LIGHTBLUE/ AQUA1/ AQUA2/
GREEN1/ GREEN2/ GREEN3/ YELLOWGREEN1/ YELLOWGREEN2/ YELLOW/ Elapsed playing time is not This is caused by how the tracks are recorded.
ORANGE1/ ORANGE2/ ORANGERED correct.
ENGLISH 23
ANDROID
NO DEVICE or Switch off the developer options on the Android device.
NA FILE Make sure the disc contains supported audio files. ( 27)
READING keeps Reconnect the Android device.
NO DISC Insert a playable disc into the loading slot. flashing. If this does not solve the problem, the connected
Android device does not support [BROWSE MODE].
CD / USB / iPod
TOC ERROR Make sure the disc is clean and inserted properly.
( 27)
PLEASE EJECT Reset the unit. If this does not solve the problem, consult
your nearest service center. Playback is intermittent Turn off the power saving mode on the Android device.
or sound skips.
READ ERROR Copy the files and folders onto the USB device again. If this
ANDROID ERROR / Reconnect the Android device.
does not solve the problem, reset the USB device or use
NADEVICE Restart the Android device.
another USB device.
NO DEVICE Connect a USB device, and change the source to USB again. ADDERROR New station creation is unsuccessful.
COPY PRO A copy-protected file is played. CHECKDEVICE Check the Pandora application on your device.
NA DEVICE Connect a supported USB device, and check the connections. NOSKIPS The skip limit has been reached.
NO MUSIC Connect a USB device that contains playable audio files. NOSTATIONS No stations are found.
iPod ERROR Reconnect the iPod. Pandora STATIONLIMIT The number of registered stations has reached its limit.
Reset the iPod. Retry after deleting unnecessary stations from your device.
Sound cannot be heard Reconnect the Android device. CONNECT ERROR Communication is unstable.
during playback. If in [HAND MODE], launch any media player application RATING ERROR Registration of thumbs up/thumbs down has failed due to
Sound output only on the Android device and start playback. insufficient network connectivity.
ANDROID
from the Android If in [HAND MODE], relaunch the current media player
THUMBS N/A Registration of thumbs up/thumbs down is not allowed.
device. application or use another media player application.
Restart the Android device. LICENSE ERROR You try to access from a country which Pandora is not
If this does not solve the problem, the connected Android deliverable.
device is unable to route the audio signal to unit. ( 27)
24
be selected. the web version of iHeartRADIO, custom stations become detected. Reset the unit. ( 3)
unavailable. Make sure you have entered the same PIN code to both
Bluetooth pairing
NOT CONNECTED Link to the application is impossible. cannot be made. the unit and Bluetooth device.
Delete pairing information from both the unit and the
CHLOCKED LOCK CODE? The selected channel is locked. Enter the correct pass
Bluetooth device, then perform pairing again. ( 15)
code to unlock. ( 14)
Echo or noise is heard Adjust the microphone units position. ( 15)
CHANUNSUB The selected channel is unsubscribed. Call
during a phone Check the [ECHO CANCEL] setting. ( 17)
1-866-635-2349 in the U.S.A. or 1-877-438-9677 in
conversation.
Canada to subscribe. ( 12)
Phone sound quality Reduce the distance between the unit and the Bluetooth
CHUNAVAIL The selected channel is unavailable. Visit
is poor. device.
www.siriusxm.com for more information about the
Move the car to a place where you can get a better signal
SiriusXM channel lineup.
Bluetooth
reception.
CHECKANTENNA Check that the antenna and its connection are in good
SiriusXM Radio
Voice calling method is Use voice calling method in a more quiet environment.
condition.
not successful. Reduce the distance from the microphone when you
CHECKTUNER Make sure the SiriusXM Vehicle Tuner is connected to speak the name.
the unit. Make sure the same voice as the registered voice tag is
NOSIGNAL Make sure the antenna is mounted outside the vehicle. used.
Sound is being Reduce the distance between the unit and the Bluetooth
SUBSCRIPTION UPDATED Your subscription is updated. Press the volume knob to
PRESS ENTER TO continue. interrupted or skipped audio player.
during playback of a Turn off, then turn on the unit and try to connect again.
CONTINUE.
Bluetooth audio player. Other Bluetooth devices might be trying to connect to the
CODE ERROR Make sure you have entered the correct pass code. unit.
( 14)
The connected Bluetooth Check whether the connected Bluetooth audio player
NO CONTENT There is insufficient content to start TuneScan. audio player cannot be supports Audio/Video Remote Control Profile (AVRCP).
SCAN CANCEL TuneScan has been aborted. controlled. (Refer to the instructions of your audio player.)
Disconnect and connect the Bluetooth player again.
ENGLISH 25
More information
Visit also the following website <www.kenwood.com/cs/ce/> for:
Latest firmware updates and latest compatible item list
Android application KENWOOD MUSIC PLAY
Any other latest information
General
This unit can only play the following CDs:
Detailed information and notes about the playable audio files are stated in an online manual
on the following website: www.kenwood.com/cs/ce/audiofile/
26
ENGLISH 27
Source name / / /
STANDBY Source name (Date/Clock)*1 Source name (*2) Clock (back to the beginning)
TUNER Frequency (Date/Clock)*1 Frequency (*2) Clock (back to the beginning)
(For FM Radio Broadcast Data System stations only) (For FM Radio Broadcast Data System stations / FM Radio Data System
Station name (Date/Clock)*1 Radio text (Date/Clock)*1 Radio text+ (R.TEXT+) stations only)
Title (Artist) Title (Date/Clock)*1 Frequency (Date/Clock)*1 (back to the beginning) Station name (*2) Radio text Radio text+ Title/Artist Frequency Clock
(back to the beginning)
CD or USB (For CD-DA) (For CD-DA)
Track title (Artist) Track title (Disc name) Track title (Date/Clock)*1 Playing time Disc name/Artist (*2) Track title/Artist Playing time Clock
(Date/Clock)*1 (back to the beginning) (back to the beginning)
(For MP3/WMA/AAC/WAV/FLAC files) (For MP3/WMA/AAC/WAV/FLAC files)
Track title (Artist) Track title (Album title) Track title (Date/Clock)*1 File name (Folder Track title/Artist (*2) Album title/artist Folder name File name Playing
name) File name (Date/Clock)*1 Playing time (Date/Clock)*1 (back to the beginning) time Clock (back to the beginning)
IPOD or Track title (Artist) Track title (Album name) Track title (Date/Clock)*1 Playing time Track title/Artist (*2) Album title/Artist Playing time Clock
ANDROID (Date/Clock)*1 (back to the beginning) (back to the beginning)
PANDORA Station name (Date/Clock)*1 Shared / Radio station (Date/Clock)*1 Track title (Artist) Station name (*2) Shared/Radio station Track title Artist
Track title (Album title) Track title (Date/Clock)*1 Playing time (Date/Clock)*1 Album title Playing time Clock (back to the beginning)
(back to the beginning)
IHEARTRADIO Station name (Date/Clock)*1 Track title (Artist) Track title (Date/Clock)*1 Station name (*2) Track title/Artist Clock (back to the beginning)
(back to the beginning)
SIRIUS XM Channel number (Status) Channel name (Status) Artist name (Status) Song title
(Status) Content information (Status) Category name (Status) Clock (Status)
(back to the beginning)
BT AUDIO Track title (Artist) Track title (Album name) Track title (Date/Clock)*1 Playing time Track title/Artist (*2) Album title/Artist Playing time Clock
(Date/Clock)*1 (back to the beginning) (back to the beginning)
AUX Source name (Date/Clock)*1 Source name (*2) Clock (back to the beginning)
*1 Battery and signal strength of the Bluetooth device will be shown if [BATT/SIGNAL] is set to [AUTO]. ( 17)
*2 Only for : Turn off the display information.
28
When connecting to an
external amplifier, connect
Rear/ front/ subwoofer output Rear/ subwoofer output
its ground wire to the cars (B) Trim plate
chassis to avoid damaging
the unit.
Antenna terminal Fuse (10A)
White
To front speaker (left) White/Black If no connections are made, do not let the wire come out from the tab.
Gray (D) Wiring harness
Brown To connect the Kenwood navigation
To front speaker (right) Gray/Black
(Mute control wire) system, refer your navigation manual
Green
To rear speaker (left) Green/Black
Purple
To rear speaker (right) Purple/Black (E) Extraction key
Blue/White To the power control terminal when using
Ignition switch
the optional power amplifier or to the
Car fuse box (Power control wire/
antenna control terminal in the vehicle
Red Antenna control wire)
(Ignition wire) (F) Screws (supplied for
Yellow Light blue/yellow )
To the steering wheel remote control
Car fuse box (Battery wire) (Steering remote adapter
Black (Ground wire) control wire)
IMPORTANT : We recommend installing the unit with a commercially MIC (Microphone input terminal) ( 15)
available custom wiring harness specific for your car and leave this job
to professionals for your safety. Consult your car audio dealer.
To the remote control, KCA-RC55MR
When connecting to an external amplifier, connect its ground wire to (optional accessory)
the cars chassis to avoid damaging the unit.
White
To front speaker (left) White/Black If no connections are made, do not let the wire come out from the tab.
Gray To Kenwood Wired Marine Remote Control unit (optional
Light blue/yellow
To front speaker (right) Gray/Black accessory)
(Marine remote control For the latest information on marine accessories please go to:
Green wire) http://www.kenwoodusa.com/Car_Entertainment/Marine/
To rear speaker (left) Green/Black
Purple
To rear speaker (right) Purple/Black Brown
To connect the Kenwood navigation system, refer your
(Mute control wire) navigations manual
Ignition switch Car fuse box
Red
(Ignition wire) Blue/White
To the power control terminal when using the optional power
Yellow (Power control wire) amplifier
Car fuse box (Battery wire) Blue
Black (Ground wire) To the antenna control terminal in the vehicle
(Antenna control wire)
Battery To the metallic body or chassis of the car
ENGLISH 31
USB
Usable Sensitivity (S/N=26dB) 8.2dBf (0.71V/75) WMA Decode Compliant with Windows Media Audio
Tuner
Quieting Sensitivity (DINS/N=46dB) 17.2dBf (2.0V/75) AAC Decode AAC-LC .aac files
Frequency Response (3dB) 30 Hz 15 kHz WAV Decode Linear-PCM
Signal-to-Noise Ratio (MONO) 64 dB FLAC Decode FLAC file (Up to 48kHz / 16bit)
Stereo Separation (1kHz) 40dB
Version Bluetooth Ver.2.1+EDR / Bluetooth 3.0
AM Frequency Range 530kHz 1700kHz (10kHz space)
Frequency Range 2.402GHz 2.480GHz
Usable Sensitivity (S/N=20dB) 29dB (28.2V)
Output Power +4dBm (MAX), 0dBm (AVE) Power Class 2
Bluetooth
Laser Diode GaAIAs Maximum Communication Line of sight approx. 10m (32.8ft)
Digital Filter (D/A) 8 times over sampling Range
Spindle Speed 500rpm 200rpm (CLV) Profile HFP (Hands-Free Profile)
A2DP (Advanced Audio Distribution Profile)
Wow & Flutter Below measurable limit AVRCP (Audio/Video Remote Control Profile)
Frequency Response (1dB) 20Hz 20kHz SPP (Serial Port Profile)
PBAP (Phonebook Access Profile)
Total Harmonic Distortion (1kHz) 0.01%
CD player
Auxiliary
/ : 105 dB Input Maximum Voltage 1000mV
: 110 dB
Input Impedance 30k
Dynamic Range 90dB
Channel Separation 85dB
MP3 Decode Compliant with MPEG-1/2 Audio Layer-3
WMA Decode Compliant with Windows Media Audio
AAC Decode AAC-LC .aac files
32
Band 8: 1.6kHz9dB
Band 9: 2.5kHz9dB
Band 10: 4kHz9dB
Band 11: 6.3kHz9dB
Band 12: 10kHz9dB
Band 13: 16kHz9dB
Preout Level/Load (CD) / /
/ :
2500mV/10k
: 4000mV/10k
Preout Impedance 600
ENGLISH 33