Académique Documents
Professionnel Documents
Culture Documents
WARRANTY
CRAFTSMAN ONE YEAR FULL WARRANTY
If this Craftsman tool fails due to a defect in material or workmanship within
one year from the date of purchase, call 1-800-4-MY-HOME R to arrange for
free repair (or replacement if repair proves impossible).
This warranty applies for only 90 days from the date of purchase if this product
is ever used for commercial or rental purposes.
This warranty does not include expendable parts, such as lamps, batteries,
bits or blades.
This warranty gives you specic legal rights, and you may also have other
rights which vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
! WARNING
Some dust created by using power tools contains chemicals known to the state
of California to cause cancer and birth defects or other reproductive harm.
Some examples of these chemicals are:
Lead from lead-based paints
Crystalline silica from bricks, cement and other masonry
products
Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do
this type of work. To reduce your exposure to these chemicals, work in a
well ventilated area and work with approved safety equipment such as dust
masks that are specially designed to lter out microscopic particles.
2
2008/05
PRODUCT SPECIFICATIONS
MOTOR
Type............................................................................. Universal
Amperes....................................................................... 15 Amp
Voltage........................................................................ 120V AC
Hz................................................................................ 60Hz
RPM (no load) ............................................................ 5000 RPM (No load)
Overload Protection.................................................... Yes
BLADE SIZE
Diameter...................................................................... 10 in.
Arbor size.................................................................... 5/8 in.
SAW
Rip fence...................................................................... Yes
Miter gauge.................................................................. Yes
Rip Capacity ................................................................ 24 in. Right & Left
Maximum Cut Depth @ 90 ......................................... 3 in.
Maximum Cut Depth @ 45 ......................................... 2-1/2 in.
Maximum Diameter Dado ............................................ 6 in. (Stackable only)
Maximum Dado Cut Width ........................................... 1/2 in.
! WARNING
To avoid electrical hazards, re hazards or damage to the tool, use proper
circuit protection.
This tool is wired at the factory for 110-120 Volt operation. It must be
connected to a 110-120 Volt / 15 Ampere time delay fuse or circuit breaker.
To avoid shock or re, replace power cord immediately if it is worn, cut or
damaged in any way.
Before using your tool, it is critical that you read and understand these
safety rules. Failure to follow these rules could result in serious injury to
you or damage to the tool.
3
SYMBOLS
WARNING ICONS
Your power tool and its Operators Manual may contain WARNING ICONS
(a picture symbol intended to alert you to, and/or instruct you how to avoid,
a potentially hazardous condition). Understanding and heeding these
symbols will help you operate your tool better and safer. Shown below are
some of the symbols you may see.
PROHIBITION
KEEP HANDS AWAY FROM BLADE: Failure to keep your hands away
from the blade will result in serious personal injury.
! DANGER
which, if not avoided, will result in death or serious injury.
! WARNING
which, if not avoided, could result in death or serious injury.
! CAUTION
if not avoided, may result in minor or moderate injury.
4
POWER TOOL SAFETY
GENERAL SAFETY INSTRUCTIONS 6. KEEP CHILDREN AWAY. All
BEFORE USING THIS POWER TOOL visitors and bystanders should be
Safety is a combination of common kept a safe distance from work area.
sense, staying alert and knowing how 7. MAKE WORKSHOP CHILD PROOF
to use your power tool. with padlocks, master switches or by
removing starter keys.
! WARNING
To avoid mistakes that could cause 8. DO NOT FORCE THE TOOL. It will
serious injury, do not plug the tool in do the job better and safer at the
until you have read and understood rate for which it was designed.
the following.
9. USE THE RIGHT TOOL. Do not
force the tool or an attachment to do
1. READ and become familiar
a job for which it was not designed.
with the entire Operators
Manual. LEARN the tools 10.USE PROPER EXTENSION
application, limitations and CORDS. Make sure your extension
possible hazards. cord is in good condition. When
using an extension cord, be sure to
2. KEEP GUARDS IN PLACE and in use one heavy enough to carry the
working order. current your product will draw. An
undersized cord will result in a drop
3. REMOVE ADJUSTING KEYS in line voltage and in loss of power
AND WRENCHES. Form the habit which will cause the tool to overheat.
of checking to see that keys and The table on page 11 shows the
adjusting wrenches are removed correct size to use depending on
from the tool before turning ON. cord length and nameplate ampere
rating. If in doubt, use the next
4. KEEP WORK AREA CLEAN. heavier gauge. The smaller the
Cluttered areas and benches invite gauge number, the heavier the cord.
accidents.
11.WEAR PROPER APPAREL. Do
5. DO NOT USE IN DANGEROUS not wear loose clothing, gloves,
ENVIRONMENTS. Do not use neckties, rings, bracelets or other
power tools in damp locations, or jewelry which may get caught in
expose them to rain or snow. Keep moving parts. Nonslip footwear is
work area well lit. recommended. Wear protective hair
covering to contain long hair.
5
12.ALWAYS WEAR EYE 17.USE RECOMMENDED
PROTECTION. Any power ACCESSORIES. Consult
tool can throw foreign this Operators Manual for
objects into the eyes and recommended accessories. The use
could cause permanent of improper accessories may cause
eye damage. ALWAYS wear Safety risk of injury to yourself or others.
Goggles (not glasses) that comply
with ANSI Safety standard Z87.1. 18.NEVER STAND ON THE TOOL.
Everyday eyeglasses have only Serious injury could occur if the
impactresistant lenses. They tool is tipped or if the cutting tool is
ARE NOT safety glasses. Safety unintentionally contacted.
Goggles are available at Sears.
NOTE: Glasses or goggles not in 19.CHECK FOR DAMAGED PARTS.
compliance with ANSI Z87.1 could Before further use of the tool, a
seriously injure you when they break. guard or other part that is damaged
should be carefully checked to
13.WEAR A FACE MASK OR DUST determine that it will operate
MASK. Sawing operation produces properly and perform its intended
dust. function check for alignment of
moving parts, binding of moving
14.SECURE WORK. Use clamps or parts, breakage of parts, mounting
a vise to hold work when and any other conditions that may
practical. It is safer than affect its operation. A guard or other
using your hand and part that is damaged should be
it frees both hands to properly repaired or replaced.
operate the tool.
20.NEVER LEAVE THE TOOL
15.DISCONNECT TOOLS FROM RUNNING UNATTENDED. TURN
POWER SOURCE before servicing, THE POWER OFF. Do not walk
and when changing accessories away from a running tool until the
such as blades, bits and cutters. blade comes to a complete stop
and the tool is unplugged from the
16.REDUCE THE RISK OF power source.
UNINTENTIONAL STARTING.
Make sure switch is in the OFF 21.DO NOT OVERREACH. Keep
position before plugging the tool in. proper footing and balance at all
times.
6
22.MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for best
and safest performance. Follow
instructions for lubricating and
changing accessories.
24.
! DANGER
People with electronic devices, such
as pacemakers, should consult
their physician(s) before using this
product. Operation of electrical
equipment in close proximity to
a heart pacemaker could cause
interference or failure of the
pacemaker.
7
TABLE SAW SAFETY
1. ALWAYS USE SAW BLADE 6. NEVER REACH behind or over the
GUARD, riving knife and anti- cutting tool for any reason.
kickback pawls for every through
sawing operation. Throughsawing 7. REMOVE the rip fence when
operations are those in which the crosscutting.
blade cuts completely through
the workpiece when ripping or 8. DO NOT USE a molding head with
crosscutting. Always be sure blade this saw.
guard is tightened securely.
9. FEED WORK INTO THE BLADE
2. ALWAYS HOLD WORK FIRMLY against the direction of rotation only.
against the miter gauge or rip fence.
10.NEVER use the rip fence as a cut-
3. ALWAYS USE a push stick or off gauge when crosscutting.
push block, especially when ripping
narrow stock. Refer to ripping 11.NEVER ATTEMPT TO FREE A
instructions in this Operators Manual STALLED SAW BLADE without
where the push stick is covered in rst turning the saw OFF. Turn
detail. A pattern for making your own power switch OFF immediately to
push stick is included on page 47. prevent motor damage.
! WARNING
DANGER and guards in place, aligned and
FREEHAND CUTTING IS THE functioning. Do not release work
MAJOR CAUSE OF KICKBACK AND before passing it completely beyond
FINGER/HAND AMPUTATIONS. the saw blade. Do not rip work that
NEVER USE THE MITER GAUGE is twisted, warped or does not have
AND FENCE SIMULTANEOUSLY. a straight edge to guide it along the
fence. Do not attempt to reverse out
5. NEVER STAND or have any part of of a cut with the blade running.
your body in line with the path of the
saw blade. Keep your hands out of 14.AVOID AWKWARD OPERATIONS
the saw blade path. and hand positions where a sudden
8
slip could cause your hand to move 21.USE ONLY saw blades recom-
into the saw blade. mended with warning that the riving
knife shall not be thicker than the
15.NEVER USE SOLVENTS to width of the groove cut by the saw
clean plastic parts. Solvents could blade and not thinner than the body
possibly dissolve or otherwise of the saw blade.
damage the material. Only a soft
damp cloth should be used to clean 22.USE PUSH-STICK OR PUSH
plastic parts. BLOCK to feed the workpiece past
the saw blade. The push-stick or
16.MOUNT your table saw on a push block should always be stored
bench or stand before performing with the machine when not in use.
any cutting operations. Refer to
ASSEMBLY on page 20. 23.Use and correct adjustment of the
riving knife.
17. ! WARNING
Never cut metals or masonry
products with this tool. This table
saw is designed for use on wood
and wood-like products.
9
ELECTRICAL REQUIREMENTS AND SAFETY
CAUTION
In all cases, make certain the
receptacle is properly grounded. If
you are not sure, have a qualied
electrician check the receptacle.
CAUTION
This tool is for indoor use only. Do
not expose to rain or use in damp
locations.
Fig. 1
Three-Pronged Plug
Grounding Prong
Properly Grounded
Three-Pronged Receptacle
Fig. 2
Grounding Lug Make sure this
is connected
to a known
ground.
Two-Pronged
Adapter Receptacle
11
ACCESSORIES AND TOOLS NEEDED FOR
ATTACHMENTS ASSEMBLY
RECOMMENDED ACCESSORIES SUPPLIED NOT SUPPLIED
! WARNING
Visit your Sears Hardware Blade wrench Flat bladed
Department or see the screwdriver
Craftsman Power and Hand Tools
Catalog to purchase recommended
accessories for this power tool. #2 Phillips screwdriver
12
CARTON CONTENTS
Separate all parts from packing cord, or turn the switch ON until
materials. Check each part with the the missing or damaged part is
illustration on the next page and the obtained and is installed correctly.
Table of Loose Parts to make certain Call 1-800-843-1682 for missing or
all items are accounted for, before damaged parts.
discarding any packing material.
NOTE: To make assembly easier, keep
B C D
E
A
J
F G H I
N
K M
L P
O
S
T U
W X Y Z AA
BB CC
14
KNOW YOUR TABLE SAW
Blade guard
Miter gauge Rip fence
Extension wing
Overload reset switch
locking lever
Miter gauge-rip Blade elevation and
fence-push stick storage tilting handwheel
ON/OFF switch with
Lock lever safety key
Foot pad
Dust bag
Hand hold
Rear table extension wing
Right extension table
Cord wrap
Blade storage
Roller wheel
Stand
15
GLOSSARY OF TERMS
ANTI-KICKBACK PAWLS Prevents the workpiece from twisting during the
the workpiece from being kicked cutting operation.
upward or back toward the front of the
table saw by the spinning blade. GUM A sticky sap from wood
products.
ARBOR The shaft on which the
blade or dado is mounted. HEEL Misalignment of the blade.
BEVEL CUT An angle cut made JAMB NUT Nut used to lock another
through the face of the workpiece. nut in place on a threaded rod or bolt.
17
ASSEMBLY
ASSEMBLE STAND (FIG. A, B, C) 5. Assemble the other upper supports
1. Unpack all parts and group by type in exactly the same manner.
and size. Refer to the parts list for 6. Attach one bottom support (5) to the
correct quantities. center of the leg using bolt (3) and
2. Attach four hooks (10) to the top nut (4). This completes the front
corner of the four legs (2) as shown. frame section.
The hooks (10) are used to hold the 7. Assemble rear frame section in
dust bag. exactly the same manner.
NOTE: Make sure the hook (10) is 8. Join front-bottom and rear-bottom
securely fastened to the corner of frame assemblies using the bottom
the leg (2). support (7), bolts and nuts.
Fig. A 10 Fig. C
10
7
2
6
5
3. Attach one long upper support with 2
label (1) to top of leg (2) using one
bolt (3) and nut (4).
NOTE: Front
1
Align detents (8) in stand leg
with support brackets to ensure ASSEMBLE THE ROLLER WHEEL
proper t. TO STAND (FIG. D, E)
Do not tighten bolts until stand is 1. Place stand upside down on level
properly aligned. surface or oor.
Position all supports to the 2. Place bottom support bracket for roller
INSIDE of the leg assembles. wheel (18) inner of the front leg (2).
4. Attach short upper supports (6) to 3. Insert the bolt (12) through the roller
other hole of leg (2) using one bolt wheel bracket (11), front leg (2),
and nut. bottom support bracket (18) and nut
(13) as shown. Tighten the nut.
Fig. B 4 4. Attach the roller wheel (14) to roller
wheel bracket (11), bolt (15) and lock
3 nut (16) using square neck bolt (15)
6
and lock nut (16) as shown.
NOTE: Do not overtighten nut as
this will not allow the wheels to turn.
10
2
8
1
18
Fig. D 16 Fig. F
14
18
13
12 15
2 9
11 9
5. Repeat steps 1-4 for left rear leg (17) ASSEMBLE TABLE SAW TO STAND
and roller wheel assembly. USING LEVER LOCK (FIG. G)
NOTE: The roller wheel assemblies 1. Attach the locking lever assembly (18)
and bottom support bracket (18) to the top of the leg (2).
can be installed on either the right- 2. Lift up the locking lever (19).
hand side or left-hand side. Always 3. Thread the two screws (20) into the
install the roller wheel assemblies holes (21) of the locking bracket (24)
and the bottom support bracket (18) and stand.
at the same time. The illustration NOTE: You may need to loosen
shows the roller wheels on the left- the two short support brackets if the
hand side. two mounting holes are not lined up
correctly. Retighten these bolts once
Fig. E you have added the lever locks.
17
4. Attach the lock nuts (22) and tighten
with a 8 mm or adjustable wrench.
5. Install the other locking lever
assemblies in exactly the same
18 manner.
6. Position the saw base on the stand.
7. Line up the lever lock cover (23) to
the saw base and push down the
locking lever (19).
8. Fasten saw to stand using four
2 locking lever assemblies (18).
NOTE: The four locking lever
Front assemblies (18) are provided for
6. Carefully set the saw in its upright quick releasing the table saw to the
position on a clean level surface. stand.
! WARNING
ASSEMBLE THE FOOT PAD TO
STAND (FIG. F) All four levers must be locked in the
1. Place all four foot pads (9) onto down position before operating saw.
each leg.
2. Place stand on level surface and Fig. G 19 23
22
adjust so all legs are contacting the
oor and are at similar angles to the 18
oor, and detents in stand leg align 20
with support brackets, then tighten
all bolts.
NOTE: Stand should not rock after 21
all bolts are tightend. 24 2
19
MOUNTING BASE TO STAND USING 5. Mark an 11 in. square (2) centered
BOLTS (FIG. H) between the four mounting holes (1).
You can also attach the saw base to the 6. Cut out and remove the square.
stand using standard bolts. 7. This opening will allow sawdust to
fall through the saw base.
1. Fasten the base to the stand using 8. Place the saw on the work surface,
the four long bolts (25), at washers and align the mounting holes of the
(26), and nuts (27). saw with those drilled through the
2. Place a washer on the bolt and insert surface.
thru the hole in saw base and slot 9. Fasten the saw to the work surface.
in stand. Attach the nut and tighten
using a 13 mm wrench. Repeat for ! WARNING
other three corners. Do not operate this machine on the
oor. This is very dangerous and
Fig. H may cause serious injury.
25 25 Fig. I
26 26
2
SQUARE
CUTOUT
27 27
1
Fig. K 1
INSTALLING THE BLADE
(FIG. M, N, O)
! WARNING
To avoid injury from an accidental
3 start, make sure the switch is in the
OFF position and the plug is not
connected to the power source outlet.
2
1. Raise the blade arbor to the
maximum height by turning the blade
elevation handwheel clockwise .
2. Remove the arbor nut (2) and outer
blade ange (3). (Fig. M)
INSTALLING THE DUST BAG (FIG. L)
Fig. M 4
! WARNING 3 2
Do not use this saw to cut and/or
sand metals. The hot chips or
sparks may ignite sawdust or the
bag material.
To prevent hazard, clean and
remove sawdust from under the
saw frequently.
3. Place the blade onto the arbor
(4) with the blade teeth pointing
1. The hooks (2) located inside of the
forward to the front of the saw. (Fig. N)
four legs are used to hold the dust
4. Make sure the blade ts ush
bag (1).
against the inner ange.
2. Attach the dust bag (1) to the four
5. Clean the outer blade ange (3)
hooks located inside of four legs.
and install it onto the arbor (4) and
against the blade. (Fig. N)
21
6. Thread the arbor nut (2) onto the REMOVING THE BLADE (FIG. N, O)
arbor, making sure the at side of
the nut is against the blade, then ! WARNING
hand-tighten. (Fig. N) To avoid injury from an accidental
7. To tighten the arbor nut (2), place start, make sure the switch is in
the open-end wrench (5) on the ats the OFF position and the plug is
of the saw arbor to keep the arbor disconnected from the power source
from turning (Fig. N). outlet.
8. Place the box-end wrench (6) on the
arbor nut (2) and turn clockwise (to 1. Remove the table insert by snapping
the rear of the saw table). (Fig. N) out from the hole (8). (Fig. O)
2. Raise the blade to the maximum
Fig. N 5 7 height by turning the blade elevation
handwheel clockwise .
3. Adjust the blade to the 90 vertical
position by unlocking the blade tilting
3
lock knob and turning the bevel
tilting handwheel counterclockwise,
and then lock into position.
2 4. Place the blade wrench (6) on the
arbor nut (2) (Fig. N).
4 5. Loosen the arbor nut (2), place the
6
open-end wrench (5) on the ats of
the saw arbor to keep the arbor from
10.Lower the blade to its minimum turning (Fig. N).
height position and place insert (1) 6. Then remove the blade (7). Clean
into position. (Fig. O) but do not remove the inner blade
ange before reassembling the
Fig. O blade (Fig. N).
1
RIVING KNIFE ASSEMBLY (FIG. P,
8 P-1, Q)
! WARNING
To avoid injury from an accidental
start, make sure the switch is in
the OFF position and the plug
! WARNING is disconnected from the power
To avoid possible injury and damage source outlet.
to the workpiece, be sure to INSTALL Never operate this saw without
THE BLADE WITH THE TEETH the riving knife in the correct
POINTING TOWARD THE FRONT OF position.
TABLE in the direction of the rotation
arrow on the blade guard.
22
Installing the riving knife assembly Aligning the riving knife (Fig. Q)
(Fig. P, P-1)
1. Remove the table insert ! WARNING
2. With the blade elevation handwheel To avoid injury from an accidental
(1), raise the blade arbor to the start, make sure the switch is in
maximum height. the OFF position and the plug
3. Loosen the blade lock handle (2). is disconnected from the power
Just turn and move the handwheel source outlet.
(1) to 45 on the bevel scale. Never operate this tool without the
4. Tighten the bevel lock handle. riving knife in the correct position.
Never operate this tool without
Fig. P 1 2 the blade guard in place for all
through sawing operations.
This adjustment was made
at the factory, but it should
be rechecked and adjusted if
necessary.
1. Remove the table insert and raise
5. Take the lock knob (6) and insert
the blade to the maximum height
thru the washer (5), middle hole in
by turning the blade elevation
the set plate (4) and slot in riving
handwheel clockwise.
knife (7).
2. Remove the blade guard and anti-
6. Place this assembly through the
kickback pawl assembly.
mounting bracket (3) located behind
3. Adjust the blade to the 0 vertical
the saw blade. Please note that the
position by unlocking the blade tilting
two pins on the bracket must be
lock knob and turning the bevel tilting
engaged in the riving knife slot and
handwheel counterclockwise, and
the two holes in the set plate.
then lock into position.
7. Make sure the riving knife (7) is in
4. To see if the blade (1) and riving
its highest position. Tighten the lock
knife (2) are correctly aligned, lay a
knob (6).
combination square along the side
8. Return the blade to 0 and place the
of the blade and against the riving
table insert in position.
knife (making sure the square is
9. Before using the saw, please follow
between the teeth of the blade).
the instructions on aligning the
5. Tilt the blade to the 45 position and
riving knife.
check the alignment again.
6. If the blade and riving knife are not
Fig. P-1 7 correctly aligned:
4 a. Loosen the locking knob (3) from
the mounting bracket (4).
5
b. Insert the washer (5) between the
3 riving knife and bracket (4) and
6
retighten the locking knob (3).
23
NOTE: When installing the blade guard,
The washers (1/4*1/2-3/32) (5) are cover the blade teeth with a piece
not included with this table saw. It of folded cardboard to protect
must be purchased separately. yourself from possible injury.
Riving knife thickness is 0.09 in. Never operate this machine
The maximum radial distance without the blade guard in place
between the riving knife and the for all through sawing operations.
toothed rim of the saw blade is 0.12
in ~ 0.31 in. (3 mm ~ 8 mm) Installing the blade guard and anti-
The tip of the riving knife shall not kickback pawl assembly (Fig. R, S, T)
be lower than 0.04 in. ~ 0.2 in. (1 1. Make sure the blade is elevated to
mm ~ 5 mm) from the tooth peak. its maximum height and the bevel is
The riving knife is thinner than the set at 0. Make sure the bevel lock
width of the kerf by approximately handle is tight.
1/64 in on each side. 2. Take the anti-kickback pawl
8. Check the riving knife and blade assembly and lift up the locking
alignment again at both 0 and 45. lever (1) located on top. (Fig R)
9. Add or remove the washers until the 3. Place the front of assembly into slot
alignment is correct. (2-Fig R) and push down making
10.Replace the table insert, blade guard sure the assembly is engaged in the
and anti-kickback pawl assembly. slots. There should be no movement
of the assembly. Push down on the
Fig. Q locking lever (1). (Fig S)
3
2 Fig. R
1
Loosen 2
5
4 3
1
Fig. S
BLADE GUARD ASSEMBLY 1
(FIG. R, S, T)
Tighten
! WARNING
To avoid injury from an accidental
start, make sure the switch is in
the OFF position and the plug is
disconnected from the power source
outlet.
24
4. Take the blade guard assembly and 2. Loosen the blade lock handle do not
locate the black sliding locking knob pull on handle just turn and move the
(4) on the back of assembly. (Fig. T) handwheel to 90 on the bevel scale.
3. Tighten the bevel lock handle.
Fig. T 4 4. Remove the anti-kickback pawl
assembly (3) by pressing the anti-
kickback pawls lever (1). (Fig. R)
5. Removing the blade guard assembly
(7) by pulling out the locking pin (4).
(Fig. T-1)
AVOID KICKBACKS (FIG. U)
(Work thrown back towards you) by
keeping the blade sharp, the rip fence
5. Insert the blade guard assembly parallel to the saw blade and by keeping
onto the riving knife so that the pin the riving knife, anti-kickback pawls and
(5) engages into slot (6) completely. guards in place, aligned and functioning.
(Fig T-1) Do not release work before passing it
6. Slide the locking knob (4) up and completely beyond the saw blade. Do not
press the guard assembly down so rip work that is twisted, warped or does
that the entire assembly is at on not have a straight edge to guide it along
the riving knife. Release the locking the fence. Do not attempt to reverse out
knob (4). of a cut with the blade running.
7. Make sure that the assembly is locked
in place both in front and back. ! WARNING
Improper riving knife alignment can
Fig. T-1
cause kickback and serious injury.
7
Fig. U
Anti- kickback pawl
6 5
Removing the blade guard and anti- INSTALLING TABLE SIDE
kickback pawl assembly (Fig. R, T-1) EXTENSIONS (FIG. V)
1. Identify the right hand table extension.
! WARNING NOTE: For illustration purposes the
To avoid injury from an accidental view in Fig. V looks through the
start, make sure the switch is in saw table to the under side of the
the OFF position and the plug is table. The right hand table extension
disconnected from the power source is the one with the measuring scale
outlet. visible from the front of the saw
1. With the blade elevation handwheel when it is installed to the right hand
raise the blade to the maximum side of the saw table.
height.
25
2. Unlock both front and rear cam 2. Snap two black plastic stops (3)
locking levers (1) on the right hand over the two rear table extension
side of the saw base by ipping the tubes (2). Make sure the locating
lever over. pin in the black plastic stops ts into
3. Insert the table extension mounting the matching hole in the extension
tubes (2) into the two matching tube. This will lock the tube into the
holes in the cam lever assemblies. extension. (Fig. W)
NOTE: Make sure the front mounting
tube has the measuring scale visible Fig. W
from the front of the saw. Bend End
4. Slide the table extension toward the
table until it rests against the saw
table. 1
5. Lock both cam locking levers by 2
pushing them in toward the cam
locking lever assemblies.
6. If the extension is not level to the 3
table, adjust by inserting the spacers
(Carton Contents S) between the
extension and the tube it mounts
onto. See page 35.
3. Insert the rear table extension
tubes (2) into the two holes in the
Fig. V
rear of the saw table, and into the
2
4 extension tube brackets under the
table. Position the rear table support
3 so that the instruction labels are
facing up. (Fig. X)
4. Tighten one extension wing stop
screw (4) on the end of the left rear
table extension tubes (2). Verify that
1 the screw is fully inserted into the
corresponding hole in the extension
tube. (Fig. X)
7. Make sure the screw (3) into the
Fig. X
matching hole (4) of the extension
mounting tube (2). 3
8. Install the left hand table extension
the same manner.
Fig. Y 2
1 4
3
Blade (Fig. BB)
1. Loosen and remove the knob (1) on
the left side of the saw housing.
2. Place extra blades (not included)
onto the arbor. Replace the knob
and tighten.
Fig. BB
INSTALLING THE PUSH-STICK 1
STORAGE HOLDER (FIG. Z)
Attach the metal push-stick storage
bracket (1) into the provided slots on
27
ADJUSTMENTS
MOVE THE TABLE SAW (FIG. CC) 4. If adjustment is needed to make the
1. Slide the table extension toward fence parallel to the groove, do the
the table until it rests against the following:
saw table and tighten the two cam- Loosen the two bolts (3) and lift
locking levers. up on the handle (2).
2. Hold the table saw rmly, pull the Hold the fence bracket (4) rmly
table saw toward you until the saw against the front of the saw table.
is balanced on the wheels. Move the fence until it is parallel
3. Move the saw to the desired with the miter gauge groove.
location for operation or store the Push the handle down and
saw in a dry environment. tighten both bolts.
5. If fence is loose when the handle is
Fig. CC in the locked (downward) position,
do the following:
Move the handle (2) upward
and turn the adjusting nut (5)
clockwise until the rear clamp is
snug.
Over-tightening the adjusting
bolts will cause the fence to come
out of alignment.
! WARNING
Failure to properly align fence can
cause kickback and serious injury.
RIP FENCE ADJUSTMENT (FIG. DD)
Fig. DD
1. The fence (1) is moved by lifting
up on the handle (2) and sliding
the fence to the desired location. 1 3
Pushing down on the handle locks
the fence in position. 4
2. Position the fence on the right side
of the table and along the edge
5
miter gauge groove.
3. Lock the fence handle. The fence 2
should be parallel with the miter
gauge groove.
28
RIP FENCE INDICATOR 3. To change angles on the miter gauge,
ADJUSTMENT (FIG. EE) loosen the lock handle (1) and rotate
1. The rip fence indicator (6) points to the miter body to the desired angle
the measurement scale. The scale as indicated by the scale. Secure in
shows the distance from the side of position by tightening the lock handle.
the fence to nearest side of the blade.
2. Measure the actual distance with a Fig. FF
rule. If there is a difference between 1
the measurement and the indicator,
adjust the indicator (6). 3
3. Loosen the screw (7) and slide the
indicator to the correct measurement
on the scale. Tighten the screw and 2
remeasure with the rule.
ADJUSTING THE TABLE INSERT
(FIG. GG)
Fig. EE
6 ! WARNING
To avoid serious injury, the table
insert (2) must be level with the
table. If the table insert is not ush
with the table, adjust the two bolts
(1) with a 4 mm hex wrench until it is
7 parallel with the table.
31
If the blade is partial to left side: Do not perform any adjustments
1. Turn the right adjustment screw (3) that are intended to increase the
counterclockwise and adjust the left power of the laser.
side adjustment screw (2) clockwise. When using the laser line, do not
2. Remeasure, as described in steps 4 point the laser beam at people and/
to 9 in the prior section. or reecting surfaces. Even a low-
3. When alignment is achieved, turn intensity laser beam can cause eye
the right adjustment screw (3) until it damage. Do not look directly into
touches the pivot rod (4). the laser beam.
If the Laser Line will not be used for
Fig. KK more than three months, remove
the batteries in order to avoid
damage from possible leakage.
The laser line does not include any
user-serviceable components. Do
not open the housing in an attempt
2 3 to repair it.
4
Repairs should only be carried out at
a service center or by an authorized
THE LASER LINE
service technician.
This tool is equipped with the Laser
NOTE: All the adjustments for the
Trac R , which is a battery-powered
operation of this machine have
laser cutting guide. The laser line
been completed at the factory.
allows the operator to anticipate the
Due to normal wear and use, some
path of the saw blade on the workpiece
occasional readjustments may be
before cutting begins.
necessary.
CAUTION-Use of controls or
! WARNING
adjustments or performance of
The laser beam is emitted when the procedures other than those
laser line is turned on. Do not stare specied herein may result in
into the beam or view it directly hazardous radiation exposure.
using optical instruments. Do not CAUTION-The use of optical
remove the warning label that is instruments with this product will
afxed to the blade guard. Avoid increase eye hazard.
aiming the laser beam directly into Do not attempt to repair or
the eyes. disassemble the laser. If unqualied
persons attempt to repair this laser
A laser beam is not a toy, and it product, serious injury may result.
should not be used by children. Any repair required on this laser
Misuse of this laser line can lead to
product should be performed by
irreparable eye damage.
authorized service center personnel.
32
LASER RADIATION. 3. If the laser line is not ush, loosen
Do not stare into the beam or view it the two set screws (1) using a small
directly using optical instruments. at bladed screwdriver that is not
Maximum output: < 1 mW provided, but do not remove them.
Wavelength: 630-670 nm 4. Use the 5 mm hex wrench that is not
Complies with 21 CFR 1040.10 and provided, adjust the laser unit (2) until
1040.11 Class II Laser Product. the laser line is parallel with the blade.
Laser Warning Label: NOTE: Be careful not to over-rotate
the laser unit. Do not rotate the laser
more than 1/8 of a turn in either
direction.
5. Adjust the set screws (1) on the left
or right side in order to shift the laser
line until it is ush with the right side
of the blade. Once proper alignment
has been achieved, tighten the set
ADJUSTING THE LASER LINE
screw on the other side slowly, until
(FIG. LL)
it touches the laser, in order to lock
! WARNING the laser into position. Turn the laser
The laser beam is emitted when the line off.
laser line is turned on. Do not stare
into beam or look directly at it using NOTE: If additional alignment is
optical instruments. Do not remove required, use thin at washers (not
the warning label that is afxed to the provided) by placing them between the
blade guard. Do not direct the laser riving knife and the mounting bracket.
into the eyes. Refer to the section of Aligning the
riving knife on page 23.
NOTE: All of the adjustments for the
operation of this machine have been Fig. LL
carried out at the factory. Occasional
readjustments may be necessary as a
result of normal wear and use. 2
33
OPERATION
BASIC SAW OPERATIONS 2. To turn the saw OFF, move the
switch downward.
RAISE THE BLADE (FIG. MM) 3. To lock the switch in the OFF position,
To raise or lower the blade, turn the grasp the end (or yellow part) of the
blade elevation handwheel (1) to the safety switch key (1), and pull it out.
desired blade height, and then tighten 4. With the safety removal key
the bevel lock handle (2) to maintain removed, the switch will not operate.
the desired blade angle. 5. If the safety removal key is removed
while the saw is running, it can be
Fig. MM turned OFF but cannot be restarted
1 2
without inserting the switch key (1).
Fig. NN
3
1
2
TILTING THE BLADE
Two methods are available for tilting
the saw blade.
OVERLOAD PROTECTION (FIG. NN)
Rapid blade tilting: This saw has an overload reset button
Loosen the bevel lock handle (2), move (3) that resets the motor after it shuts off
the handwheel (1) to the desired angle, due to overloading or low voltage. If the
then tighten the bevel lock handle. motor stops during operation, turn the
Fine adjustment blade tilting: ON / OFF switch to the OFF position.
Loosen the bevel lock handle (2), push Wait about ve minutes for the motor to
in the handwheel (1) and at the same cool, the push the reset button (3) and
time turn the handwheel (1) to tilt the turn the switch to the ON position.
saw blade. When the saw blade is at
! WARNING
the desired angle, tighten the bevel
lock handle (2). To avoid injury, the ON / OFF switch
should be in the OFF position and
ON/OFF SWITCH (FIG. NN) the plug removed from the power
The ON / OFF switch has a safety source while the cool down takes
removal key. With the key removed from place, to prevent accidental starting
the switch, unauthorized and hazardous when the reset button is pushed.
use by children and others is minimized. Overheating may be caused by
1. To turn the saw ON, insert the safety misaligned parts or a dull blade or
switch key (1) into the slot in the undersized extensing cord. Inspect
switch (2). Move the switch upward your saw for proper setup before
to the ON position. using it again.
34
USING THE TABLE EXTENSION grain of the workpiece. (It is not safe to
(FIG. OO, PP) rip or crosscut by freehand). Ripping
If the table extension is not parallel requires the use of the rip fence, and
with the table, remove the bolts (1) and crosscutting requires the miter gauge.
position the extension leveling spacers NEVER USE THE TWO AT THE
(2) between the table extension and SAME TIME.
tube until it is parallel with the table,
then tighten the bolts. ! WARNING
NOTE: See page 14 for table of loose
Before using the saw each time,
parts ITEM: S
check the following:
1. The blade is tightened to the arbor.
Fig. OO
2. The bevel angle lock knob is
tightened.
3. If ripping, make sure the fence
is locked into position and
2 is parallel to the miter gauge
groove.
1 4. The blade guard is in place and
working properly.
5. Safety glasses are worn.
1. Release the extension cam locking
levers (3). The failure to adhere to these
2. Slide the extension (4) out until the common safety rules, and those
correct measurement is displayed printed in the front of this manual,
on the tube scale. The user sights can greatly increase the likelihood
the scale off the edge of the table. of injury.
3. Tighten all extension cam locking
levers. RIPPING (FIG. QQ, RR)
Fig. PP ! WARNING
To prevent serious injury:
Never use a miter gauge when
ripping.
Never use more than one rip fence
during a single cut.
Do not allow familiarity or frequent
3 use of your table saw to cause
4 careless mistakes. Remember
CUTTING OPERATIONS that even a careless fraction of
There are two basic types of cuts: a second is enough to cause a
ripping and crosscutting. Ripping is severe injury.
cutting along the length and the grain of Keep both hands away from the
the workpiece. Crosscutting is cutting blade and clear from the path of
either across the width or across the the blade.
35
The workpiece must have a ! WARNING
straight edge against the fence
When width or rip narrower than
and must not be warped, twisted,
2 in. the push stick cannot be
or bowed when ripping.
used because the blade guard will
interfere. Use the auxiliary fence (4)
1. Remove the miter gauge and store it
and push block (5) as shown.
in the storage compartment in the
base of the saw.
Fig. RR
2. Secure the rip fence to the table.
3. Raise the blade so it is about 1/8 in. 4
7
higher than the top of the workpiece.
4. Place the workpiece at on the table
and against the fence. Keep the
workpiece away from the blade.
5. Turn the saw ON and wait for the
5
blade to come to full speed.
6. Slowly feed the workpiece into the 6
blade by pushing forward only on the
workpiece section (1) that will pass
8. Continue pushing the workpiece (6)
between the blade and the fence.
with the push stick (3-Fig. QQ) or
(Fig. QQ)
push block until it passes through
7. Keep your thumbs off the table top.
the blade guard and clears the rear
When both of your thumbs touch the
of the table. (Fig. RR)
front edge of the table (2), nish the
9. Never pull the piece back when the
cut with a push stick (3). To make an
blade is turning. Turn the switch
additional push stick, use the pattern
OFF. When the blade completely
on page 47. (Fig. QQ)
stops, you can then remove the
! WARNING workpiece.
AVOID KICKBACK by pushing ! WARNING
forward on the section of the
Never attempt to pull the workpiece
workpiece that passes between the
backwards during a cutting
blade and the fence. Never perform
operation. This will cause kickback
any freehand operations.
and serious injury to the user can
occur. When the blade completely
Fig. QQ
6 stops, raise the anti-kickback pawls
(7) on each side of the riving knife
3 and slide the workpiece out.
2 1
36
BEVEL RIPPING MAKE A FEATHERBOARD (FIG. SS)
This cut is the same as ripping except Select a solid piece of lumber
the blade bevel angle is set to an angle approximately 3/4 in thick, 4 in wide and
other than 00. 18 in long. To make a featherboard, cut
one end of the lumber at 60 degrees,
RIPPING SMALL PIECES then cut 8 in-long slots 1/4 in apart on
To avoid injury from the blade contact, the angled end as shown in Fig. SS.
never make cuts narrower than 3/4 in.
wide. Fig. SS
1. It is unsafe to rip small pieces.
Instead, rip a larger piece to obtain
1/8 in
4 in
3 in
the size of the desired piece.
60o
2. When a small width is to be ripped,
3 in
your hand cannot be safely put
3/4 in
8 in
between the blade and the rip fence,
use push stick or push block to pass 18 in
the workpiece completely through
and past the blade.
USE A FEATHERBOARD (FIG. TT)
HELPFUL DEVICES 1. Lower the saw blade (1).
In order to make some of cuts, it is 2. Position the rip fence (2) to the
necessary to use the devices like, push desired adjustment and lock the rip
block, featherboard and auxiliary fence, fence.
which you can make yourself. Here are 3. Place the workpiece (3) against the
some templates for your reference. fence and over the saw blade area.
4. Adjust the featherboard (4) to resist
FEATHERBOARD (FIG. SS, TT) the workpiece forward of the blade.
A featherboard is a device used to 5. Attached the C-clamps (5) to secure
help control the workpiece by guiding the featherboard to the edge of the
it securely against the table or fence. table.
Featherboards are especially useful
when ripping small workpieces and for Fig. TT
completing non-through cuts. The end 1
is angled with a number of short kerfs 2
to give a friction hold on the workpiece 5
and locked in place on the table
with C-clamps. Test that it can resist
kickback.
! WARNING
Place the featherboard against the
uncut portion of the workpiece to 3
avoid kickback that could cause 4
serious personal injury.
37
AUXILIARY FENCE (FIG. UU) MAKE A PUSH BLOCK (FIG. VV)
Making the base: Making the base:
Start with a piece of 3/8 in. plywood Start with a 3/8 in. plywood at least
at least 5-1/2 in. wide or wider and 5-1/2 in. wide or wider and 12 in.
21 in. long or longer. long or longer.
Cut the piece to shape and size Cut the piece to shape and size as
shown: shown.
Making the side: Making the handle:
Start with a piece of 3/4 in. Start with a 3/4 in. hardwood at
hardwood at least 1-3/4 in. wide or least 5 in. wide or wider and 7 in.
wider and 21 in. long or longer. long or longer.
Cut the piece to shape and size Cut the piece to shape and size as
shown: shown.
Putting it together: Making the bracket:
Fasten the pieces together with glue Start with a 3/8 in. wood at least 3/8
and woodscrews. in. wide or wider and 2-1/2 in. long
or longer.
! WARNING Cut the piece to shape and size as
Make sure the screw heads do shown.
not stick out from the bottom of Putting it together:
the base, they must be ush or Fasten the base and handle
recessed. The bottom must be at together with glue and woodscrews.
and smooth enough to rest on the
saw table without rocking. ! WARNING
Make sure the screw heads do not
Fig. UU stick out from the bottom of the base,
they must be ush or recessed.
5-1/2 in
3/4
3/8
in.
har Fig. VV
7 in
in. dw 1
ply ood
wo
3/8 in. thick plywood base
od
The edge must be
parallel with the face 5 in
12 in
3/8 in
PUSH BLOCK 2-1/2 in
2-1/2 in
! WARNING
4
Only this type cut is made without
install the blade assembly, anti-
kickback pawls assembly.
To avoid injury from an accidental
start, make sure the switch is in
the OFF position and the plug 2
is disconnected from the power
source outlet. 3 1
41
DADO CUTS (FIG. dd, ee) chippers as shown in the dado sets
instruction manual. Blade/chippers
! WARNING must not exceed 1/2 in. total in
Only Stackable dado blades can width.
be used on this saw.
DO NOT use Adjustable or Wobble Fig. dd
type dadoes.
2
The maximum dado cut width is
1/2 in.
1
1. Remove the table insert, saw blade,
anti-kickback pawl assembly, blade
guard assembly and riving knife
3
assembly for dado cuts ONLY.
Reinstall and realign blade guard
for all through-sawing operations. 7. Check the saw to ensure that the
Install a dado not exceeding 6 in. in dado will not strike the housing,
diameter and 1/2 in. in width insert, or motor when in operation.
2. Install the dado table insert making
sure that the rear of the insert is
! WARNING
ush with the table. If the dado insert
is not ush with the table, adjust the For your own safety, always replace
two bolts on the insert with a 4 mm the blade, blade guard assembly,
hex wrench until it is parallel with the anti-kickback pawl assembly,
table. riving knife assembly and table
3. Instructions for operating the dado insert when you nished the dado
is packed with the separately operation.
purchased dado set.
4. The arbor (1) on this saw restricts Fig. ee
the maximum width of the cut to 1/2 Dado cut
in.
5. It is not necessary to install the
outside ange (2) before threading
on the arbor nut (3) for the maximum
1/2 in. dado cuts. Make sure that the
arbor nut (3) is tight, and that at least
one thread of the arbor sticks out
past the nut.
6. Use only the correct number of
round outside blades and inside
42
MAINTENANCE
MAINTAINING YOUR TABLE SAW 1. With the saw disconnected from the
power source, turn the saw upside
GENERAL MAINTENANCE down and pull up and push down on
the motor unit.
! WARNING 2. Observe any movement of the
For your own safety, turn the switch motor mounting mechanism.
OFF and remove the switch key. 3. Loosen or tighten the four hex
Remove the plug from the power screws (1) by hex wrench for smooth
source outlet before maintaining or operation. Only 1/8 turn at a time.
lubricating your saw. NOTE: Do not adjust the screw
more than 1/2 turn as this may
1. Clean out all sawdust that has damage the mechanism.
accumulated inside the saw cabinet
and the motor. Fig. ff
2. Polish the saw table with an 1
automotive wax to keep it clean and to
make it easier to slide the workpiece.
3. Clean cutting blades with pitch and
gum remover.
4. A worn, cut, or damaged power cord
should be replaced immediately. 1
! WARNING 1
All electrical or mechanical repairs
should be attempted only by a
4. Place a small amount of dry
trained repair technician. Contact
lubricant on the bevel gear (2). The
customer service for assistance. Use
worm gear (3) must be kept clean
only identical replacement parts. Any
and free of sawdust, gum, pitch,
other parts may create a hazard.
and other contaminants for smooth
operations.
5. Use liquid dishwashing detergent
and water to clean all plastic parts.
Fig. gg
NOTE: Certain cleaning chemicals
can damage plastic parts.
6. Avoid use of cleaning chemicals or
solvents, ammonia and household
detergents containing ammonia. 2
3
BLADE RAISING AND TILTING
MECHANISM (FIG. ff, gg)
After every ve hours of operation,
the blade raising mechanism and
tilting mechanism should be checked
for looseness, binding, or any other
abnormalities.
43
MAINTENANCE
NOTE: If excessive looseness 6. Remove the black plastic cap (2)
is observed in any part of the from the side of the motor (3).
blade raising mechanism or tilting 7. Carefully remove the spring-loaded
mechanism, take the complete unit to a cap, and then pull out the brush and
Service Center. replace.
8. Replace the other side.
LUBRICATION 9. The ears on the metal end of the
All motor bearings are permanently assembly go in the same hole
lubricated at the factory and require no the carbon part ts into. Do not
additional lubrication. On all mechanical overtighten the plastic cap.
parts of your table saw where a pivot 10. Carefully set the saw in a upright
or threaded rod are present, lubricate position on a clean level surface.
using graphite or silicone. These dry 11.Replace the blade guard, blade,
lubricants will not hold sawdust as rip fence, miter gauge and stand
would oil or grease. assembly to the table saw.
NOTE: To reinstall the same brushes,
REPLACING THE CARBON rst make sure the brushes go back in
BRUSHES (FIG. hh, ii) the way they came out. This will avoid
a break-in period that reduces motor
! WARNING performance and increases wear.
Always disconnect the plug from the
power source before inspecting the Fig. hh 3
brushes. 2
The carbon brushes included with the
unit will last approximately 50 hours
of running time, or 10,000 ON/OFF
cycles. Replace both carbon brushes
when either has less than 1/4 in. length
of carbon remaining, or if the spring or
wire is damaged or burned.
1. Remove the blade guard, blade,
rip fence, miter gauge and stand
assembly from the table saw. 1
Fig. ii
2. Lower the blade height to its
minimum setting. This will make the
brushess location easier to access.
3. Place cardboard or an old blanket
on the oor to protect the saw table
surface.
4. Place the saw upside down on the
protective material.
5. Tilt the blade elevation/tilting 3
handwheel (1) to the 45 position. 2
44
TROUBLESHOOTING GUIDE
! WARNING
To avoid injury from accidental starting, always turn switch OFF and unplug
the tool before moving, replacing the blade or making adjustments.
Material pinched 1. Rip fence not aligned with 1. Check and adjust rip fence.
blade when blade. 2. Select another piece of
ripping. 2. Warped wood, edge against wood.
fence is not straight.
Material binds 1. Riving knife not aligned 1. Check and align riving knife
on riving knife. correctly with blade. with blade.
Saw makes 1. Dull blade. 1. Replace blade.
unsatisfactory 2. Blade mounted backwards. 2. Turn the blade around.
cuts. 3. Gum or pitch on blade. 3. Remove blade and clean
4. Incorrect blade for work being with turpentine and coarse
done. steel wool.
5. Gum or pitch on blade 4. Change the blade.
causing erratic feed. 5. Clean table with turpentine
and steel wool.
45
TROUBLESHOOTING GUIDE
! WARNING
To avoid injury from accidental starting, always turn switch OFF and unplug
the tool before moving, replacing the blade or making adjustments.
Material kicked 1. Rip fence out of adjustment. 1. Align rip fence with miter
back from blade. 2. Riving knife not aligned with gauge slot.
blade. 2. Align riving knife with blade.
3. Feeding stock without rip 3. Install and use rip fence.
fence. 4. Install and use riving knife.
4. Riving knife not in place. (with guard)
5. Dull blade. 5. Replace blade.
6. The operator letting go of 6. Push material all the way
material before it is past saw past saw blade before
blade. releasing work.
7. Miter angle lock knob is not 7. Tighten knob.
tight.
Blade does 1. Sawdust and dirt in elevation/ 1. Brush or blow out loose dust
not raise or tilt tilting mechanisms. and dirt.
freely.
Blade does 1. Extension cord too light or 1. Replace with adequate size
not come up to too long. cord.
speed. Reset 2. Low house voltage. 2. Contact your electric
trips too easily. company.
Machine 1. Saw not mounted securely to 1. Tighten all mounting
vibrates workbench. hardware.
excessively. 2. Bench on uneven oor. 2. Reposition on at level
3. Damaged saw blade. surface.
3. Replace blade.
Does not make 1. Miter gauge out of 1. Adjust miter gauge.
accurate 45 and adjustment.
90 crosscuts.
46
PUSH STICK CONSTRUCTION
Use good quality plywood or solid wood
Use 1/2 in. or 3/4 in. material
Push stick MUST be thinner than the width of
material being cut
Drill Hole
For Hanging
m)
0m
Notch To
(40
Prevent Hand
n.
From Slipping
4i
-3/
15
Cut Here To
Push 1/2 in. Wood
Cut Here To
Push 3/4 in. Wood
900
200 - 300
47
PARTS LIST
10 in. TABLE SAW MODEL NO. 137.218070
! WARNING
When servicing use only CRAFTSMAN replacement parts. Use of any other
parts many create a HAZARD or cause product damage. Any attempt to
repair or replace electrical parts on this Table Saw may create a HAZARD
unless repair is done by a qualied service technician. Repair service is
available at your nearest Sears Service Center.
PARTS LIST FOR TABLE SAW SCHEMATIC A
I.D. Description Size QTY I.D. Description Size QTY
0B6V CLAMP HANDLE M6*1.0 1 2FTB EXTENSION WING (LEFT) #AW 1
0J5L FLAT WASHER 5*10-0.3 10 2GYV SLIDING BASE ASSY 2
0J6V FLAT WASHER 3/16*3/8-0.022 8 2JHQ SLIDING BASE ASSY 2
0J76 FLAT WASHER 1/4*3/4-1/16 2 2NE3 NEEDLE POINTER 1
0J78 FLAT WASHER 1/4*1/2-3/32 1 2NE4 NEEDLE POINTER 1
0JAF EXTERNAL TOOTH LOCK WASHER 5 1 2NRD EXTENSION WING ROD 1
0JVY HEX. SOC. HD. CAP BOLT M6*1.0-16 1 2NRE EXTENSION WING ROD 1
0K6Y CR. RE. TRUSS HD. SCREW M4*0.7-10 2 2NRF EXTENSION WING ROD 1
0K7E CR. RE. ROUND WASHER HD. SCREW M5*0.8-6 1 2NRG EXTENSION WING ROD 1
0K9T HEX. HD. TAPPING SCREW M5*16-16 2 2NSC REAR OUT-FEED SUPPORT ROD 2
0K9U HEX. HD. TAPPING SCREW M5*16-25 8 2RV8 REAR OUT-FEED SUPPORT 1
0KAE CR. RE. PAN HD. TAPPING SCREW M5*0.8-10 3 2RVE INSERT #23 1
0KBA CR. RE. PAN HD. TAPPING SCREW M5*16-12 4 2RVP SET PLATE 1
0KBQ CR. RE. PAN HD. TAPPING SCREW M5*16-10 1 2RVQ RIVING KNIFE 1
0KCX CR. RE. PAN HD PLAIN WASHER M5*0.8-10 4 2RVX BLADE GUARD 1
TAPPING SCREW
0KCY CR. RE. PAN HD PLAIN WASHER M5*0.8-12 8 2RW4 NEEDLE POINTER 1
TAPPING SCREW
0SZY SLIDING BASE ASSY 1 2RW6 SET PLATE 1
0SZZ SLIDING BASE ASSY 1 2RWG EXTENTION WING (RIGHT) #AW 1
10K5 HEX. SOC. HD. CAP BOLT M5*0.8-8 4 2RXQ SPACER 2
10LB BOLT CLAMP 1 2RXS RIP FENCE ASSY 1
CR. RE. TRUSS HD. ROUND NECK
10LE M5*0.8-16 3 2SUU SCALE(RIGHT) 1
SCREW
212M LEAD WIRE ASSY 1 2SUV SCALE(LEFT) 1
25AP HEX. SOC. HD. CAP BOLT M6*1.0-25 1 2SUW SCALE(LEFT) 1
26LU WARNING LABEL 1 2SUX SCALE(RIGHT) 1
275F LOCATION SEAT 2 2SUY SCALE 1
28N2 AAA BATTERY 2 2SV2 WARNING LABEL 1
290M CAUTION LABEL 1 2SUS INSTRUCTIONS MANUAL 1
29R2 WARNING LABEL 2 2T6B HARDWARE BAG ASSY 1
29WT LASER SET ASSY 1 2T6C BLADE GUARD ASSY 1
CR. RE PAN HD PLAIN WASHER
2AZ7 TAPPING SCREW M2.6*24-8 1 2T6D ANTI-KICKBACK PAWL ASSY 1
2DUB CR. RE. ROUND WASHER HD. SCREW M5*0.8-12 3 2T6F HANDLE 2
2EU0 TILTING SCALE 2 2T87 LABEL(LASER)-LEFT 1
2EVJ MITER GAUGE ASSY 1 2TB9 LABEL(LASER)-RIGHT 1
2FSV TABLE #AW 1
48
10 in. TABLE SAW MODEL NO. 137.218070
SCHEMATIC A
MAN ATORS
UAL
R
OPE
49
10 in. TABLE SAW MODEL NO. 137.218070
50
10 in. TABLE SAW MODEL NO. 137.218070
SCHEMATIC B
51
10 in. TABLE SAW MODEL NO. 137.218070
52
10 in. TABLE SAW MODEL NO. 137.218070
2TDW4
2SK64
2SB3
2SBX 2SE2
2A92
2SK8
2SB2
2SKC 0JPS4
0KHX2
0J4F4
0KQW2
2SXP2 0KRR4
2SE1 2RWE4
0KQY
2T5A
0KJ7
2SXQ2
22FZ
2RW1 2SV0
0KRR14
0KRR
2BUD2
2BUE
2SK72
2BV24
0Z1G14
2RVD4
53
NOTE
54
NOTE
55
Get it fixed, at your home or ours!
Your Home
For expert troubleshooting and home solutions advice:
www.managemyhome.com
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.) 1-800-469-4663 (Canada)
www.sears.com www.sears.ca
56