Académique Documents
Professionnel Documents
Culture Documents
Instructions: Check each test method for which you are requesting accreditation.
ADMIXTURES
_____ 02/A36 ASTM C311 Sampling and Testing Fly Ash or Natural Pozzolans for
Use as a Mineral Admixture in Portland Cement
Concrete
AGGREGATES
_____ 02/A07 ASTM C117 Materials Finer than 75-m (No. 200) Sieve in Mineral
Aggregates by Washing
_____ 02/A09 ASTM C127 Specific Gravity and Absorption of Coarse Aggregate
_____ 02/A10 ASTM C128 Specific Gravity and Absorption of Fine Aggregate
_____ 02/A12 ASTM C136 Sieve Analysis of Fine and Coarse Aggregates
_____ 02/A13 ASTM C142 Clay Lumps and Friable Particles in Aggregates
_____ 02/A16 ASTM D2419 Sand Equivalent Value of Soils and Fine Aggregate
CEMENT
_____ 02/A21 ASTM C157 Length Change of Hardened Cement Mortar and
Concrete
_____ 02/A26 ASTM C191 Time of Setting of Hydraulic Cement by Vicat Needle
_____ 02/A29 ASTM C265 Calcium Sulfate in Hydrated Portland Cement Mortar
_____ 02/A31 ASTM C305 Mechanical Mixing of Hydraulic Cement Pastes and
Mortars of Plastic Consistency
_____ 02/A32 ASTM C430 Fineness of Hydraulic Cement by the 45-m (No. 325)
Sieve
_____ 02/A33 ASTM C451 Early Stiffening of Portland Cement (Paste Method)
CONCRETE
_____ 02/A40 ASTM C78 Flexural Strength of Concrete Simple Beam with Third
Point Loading
_____ 02/A41 ASTM C192 Making and Curing Concrete Specimens in the
Laboratory (requires C173, C231, C138, C143, C136,
C127, C128, C566, C1064, C29, C40, C117)
_____ 02/A45 ASTM C42 Obtaining and Testing Drilled Cores and Sawed Beams
of Concrete
_____ 02/A54 ASTM C666 Resistance of Concrete to Rapid Freezing and Thawing
_____ 02/A55 ASTM C140 Sampling and Testing Concrete Masonry Units and
Related Units
GEOTEXTILES
_____ 02/L48 ASTM D5321 Determining the Coefficient of Soil and Geosynthetic or
Geosynthetic and Geosynthetic Friction by the Direct
Shear Method
_____ 02/L49 ASTM D6243 Determining the Internal and Interface Shear Resistance
of Geosynthetic Clay Liner by Direct Shear Method
_____ 02/M11 ASTM D1188 Bulk Specific Gravity of Compacted Bituminous Mixtures
Using Paraffin-Coated Specimens
_____ 02/M20 ASTM D2872 Effect of Heat and Air on a Moving Film of Asphalt
(Rolling Thin Film Oven Test)
_____ 02/M21 ASTM D3142 Specific Gravity or API Gravity of Liquid Asphalts by
Hydrometer Method
_____ 02/M22 ASTM D3143 Flash Point of Cutback Asphalt with Tag Open Cup
Apparatus
_____ 02/M23 ASTM D3289 Specific Gravity or Density of Semi-Solid and Solid
Bituminous Materials by Nickel Crucible
_____ 02/M27 ASTM D6307 Asphalt Content of Hot-Mix Asphalt by Ignition Method
_____ 02/M30 ASTM D6927 Marshall Stability and Flow of Bituminous Mixtures
_____ 02/M31 ASTM D6925 Preparation and Determination of the Relative Density of
Hot Mix Asphalt (HMA) Specimens by Means of the
Superpave Gyratory Compactor
_____ 02/L04 ASTM D698 Moisture Density Relations of Soils and Soil-Aggregate
Mixtures Using 5.5-lb Rammer and 12-inch Drop
_____ 02/L06 ASTM D1140 Amount of Material in Soils Finer Than the #200 Sieve
_____ 02/L07 ASTM D1556 Density of Soil by the Sand Cone Method
_____ 02/L08 ASTM D1557 Moisture Density Relations of Soils and Soil-Aggregate
Mixtures Using 10-lb Rammer and 18-inch Drop
_____ 02/L13 ASTM D2216 Determination of Water (Moisture) Content of Soil, Rock,
and Soil-Aggregate Mixtures
_____ 02/L14 ASTM D2217 Wet Preparation of Soil Samples for Particle Size
Analysis and Determination of Soil Constants
_____ 02/L18 ASTM D3080 Direct Shear Tests of Soils Under Consolidated Drained
Conditions
_____ 02/L19 ASTM D4254 Minimum Index Density of Soils and Calculation of
Relative Density
_____ 02/L20 ASTM D4318 Liquid Limit, Plastic Limit, and Plasticity Index of Soils
_____ 02/L24 ASTM D2974 Moisture, Ash, and Organic Matter of Peat Material
_____ 02/L27 ASTM D4253 Max. Index Density of Soils - Vibratory Table
_____ 02/L31 ASTM D2167 Density of Soil in Place by the Rubber Balloon Method
_____ 02/L53 ASTM D3967 Splitting Tensile Strength of Intact Rock Core
Specimens
_____ 02/L54 ASTM D4543 Preparing Rock Core Specimens and Determining
Dimensional and Shape Tolerances
_____ 02/L56 ASTM D5607 Performing Laboratory Direct Shear Strength Tests of
Rock Specimens Under Constant Normal Force
_____ 02/L57 ASTM D4644 Slake Durability of Shales and Similar Weak Rocks
_____ 02/L58 ASTM D4648 Laboratory Miniature Vane Shear Test for Saturated
Fine-Grained Clayey Soil
_____ 02/L60 ASTM D6938 In-Place Density and Water Content of Soil and Soil-
Aggregate by Nuclear Methods (Shallow Depth)
_____ 02/L61 ASTM D7012 Compressive Strength and Elastic Moduli of Intact Rock
Core Specimens Under Varying States of Stress and
Temperatures
NVLAP will indicate that a laboratory complies with the following standard practices and specifications if:
(a) accreditation is granted for all test methods required by the standard practice or specification, and (b)
all conditions and requirements stated in the standard practice or specification are complied with.
Applicants must be aware that some of these standards require that a professional engineer be in charge
of the laboratory, and that performance of a minimum set of test methods is required.
_____ 02/A38 ASTM E329 Standard Specification for Agencies Engaged in the
Testing and/or Inspection of Materials Used in
Construction
_____ 02/A39 ASTM C1077 Standard Practice for Laboratories Testing Concrete and
Concrete Aggregates for Use in Construction and
Criteria for Laboratory Evaluation (requires ASTM C31,
C39, C40, C117, C127, C128, C136, C138, C143, C172,
C173)
_____ 02/A49 ASTM C1222 Standard Practice for Evaluation of Laboratories Testing
Hydraulic Cement
_____ 02/A50 ASTM C1093 Standard Practice for the Accreditation of Testing
Agencies for Unit Masonry
_____ 02/L32 ASTM D3740 Standard Practice for Minimum Requirement for
Agencies Engaged in the Testing and/or Inspection of
Soil and Rock as Used in Engineering Design and
Construction
_____ 02/L59 ASTM D4718 Standard Practice for Correction of Unit Weight and
Water Content for Soils Containing Oversize Particles
_____ 02/M26 ASTM D3666 Standard Specification for Minimum Requirements for
Agencies Testing and Inspecting Bituminous Paving
Materials
_____ 02/M28 ASTM E1816 Standard Practice for Ultrasonic Examinations Using
Electromagnetic Acoustic Transducer (EMAT)
Techniques
_____ 02/M32 ASTM D5404 Standard Practice for Recovery of Asphalt from Solution
Using the Rotary Evaporator
_____ 02/S07 ASTM E709 Standard Recommended Practice for Magnetic Particle
Examination
_____ 02/S08 ASTM E165 Standard Recommended Practice for Liquid Penetrant
Inspection Method
STEEL MATERIALS
_____ 02/S02 ASTM A370 Guided Bend Test for Ductility of Welds - Steel Products
(Sec. 14)/E190
_____ 02/S03 ASTM A370 Semi-Guided Bend Test for Ductility - Steel Products
(Sec. 14)/E290
_____ 02/S09 AWS D1.1, Sec. 6, Structural Welding Code-Steel: Sec. 6, Part E,
Part E Radiographic Testing
_____ 02/S10 AWS D1.1, Sec. 6, Structural Welding Code-Steel: Sec. 6, Part F, Ultrasonic
Part F Testing
Laboratories seeking accreditation for Cement, Concrete, Aggregates, Soil or Bituminous testing
are required to participate in the CCRL/AMRL proficiency sample programs. Individual participation
in these programs is determined by the scope of accreditation desired. For example, laboratories
applying for accreditation for Concrete testing only, will need to participate only in the Concrete
sample program. Those applying for accreditation for Cement, Concrete, Aggregates, Soil, and
Bituminous testing will need to participate in all five of these programs.
The proficiency sample program involves testing a sample of material in accordance with the
standard test methods specified. The test results are returned for statistical analysis. Group values
such as the average, the standard deviation and the coefficient of variation are determined.
Individual results are then compared with the group values and a rating for the specific test is
assigned. The proficiency test results can be used for self-evaluation as well as review by NVLAP.
To participate in the CCRL/AMRL proficiency sample programs, please contact the following:
Select the sample programs most applicable to the test methods for which accreditation is being
requested. Laboratories that are new to the proficiency sample program(s) must submit
payment with the participation request forms directly to CCRL/AMRL. In addition, each new
laboratory is required to complete and return to NVLAP the Proficiency Testing Release form,
which is included in this package. CCRL and AMRL will send a copy of the proficiency testing
results directly to NVLAP.
Laboratories that are currently enrolled in the proficiency sample program(s) should not
resubmit request forms or the release form, or send payment. CCRL/AMRL will automatically
invoice each participating laboratory before the next proficiency testing round is sent out. To
ensure continuing participation, the annual invoice must be paid by the due date noted on the
invoice.
______________________
(Date)
Street Address:
P. O. Box:
Authorized Representative
(Signature)
Subject: Release of CCRL/AMRL Proficiency Sample Reports to the National Voluntary Laboratory
Accreditation Program (NVLAP)
Permission is given for the Cement and Concrete Reference Laboratory (CCRL) and the AASHTO
Materials Reference Laboratory (AMRL) to release our laboratory's proficiency sample program results to
NVLAP, for use in the evaluation process for accreditation. These results fulfill the relevant requirements
for NVLAP proficiency testing for the appropriate testing field(s) under the Construction Materials Testing
laboratory accreditation program.
This release remains in effect as long as this laboratory participates in the NVLAP program.
Reports from the following proficiency sample programs may be released to NVLAP:
PROFICIENCY TESTING
CCRL AMRL
[ ] C 270 Masonry Mortar [ ] Hot Mix Asphalt Ignition Oven [ ] Fine Aggregate
[ ] Concrete Masonry Units [ ] Hot Mix Asphalt Hveem Design [ ] Soil Classification and
Compaction
Return to: Beth Hackett, NIST/NVLAP, 100 Bureau Drive, Stop 2140, Gaithersburg, MD 20899-2140; e-
mail <bethany.hackett@nist.gov>.