Académique Documents
Professionnel Documents
Culture Documents
txt
Model Notes
Input Echo:
Description:
Parent Geometry
Parent Outside Diam. : 24500.000 mm.
Thickness : 8.000 mm.
Fillet Along Shell : 8.000 mm.
Parent Properties:
Cold Allowable : 114.5 MPa
Hot Allowable : 114.5 MPa
Material DB # 1005718.
Ultimate Tensile (Amb) : 399.9 MPa
Yield Strength (Amb) : 248.2 MPa
Yield Strength (Hot) : 239.9 MPa
Elastic Modulus (Amb) : 202720.0 MPa
Poissons Ratio : 0.300
Expansion Coefficient : 0.1180E-04 mm./mm./deg.
Weight Density : 0.0000E+00 N /cu.mm.(NOT USED)
Nozzle Geometry
Nozzle Outside Diam. : 273.000 mm.
Thickness : 12.700 mm.
Length : 250.000 mm.
Nozzle Weld Length : 8.000 mm.
RePad Width : 156.000 mm.
RePad Thickness : 8.000 mm.
RePad Weld Leg : 8.000 mm.
Nozzle Tilt Angle : 0.000 deg.
Distance from Top : 9850.000 mm.
Distance from Bottom : 350.000 mm.
Nozzle Properties
Cold Allowable : 117.9 MPa
Hot Allowable : 117.9 MPa
Page 1
RESULT.txt
Material DB # 1008218.
Ultimate Tensile (Amb) : 413.7 MPa
Yield Strength (Amb) : 241.3 MPa
Yield Strength (Hot) : 233.1 MPa
Elastic Modulus (Amb) : 202720.0 MPa
Poissons Ratio : 0.300
Expansion Coefficient : 0.1180E-04 mm./mm./deg.
Weight Density : 0.0000E+00 N /cu.mm. (NOT USED)
Model Notes
Forces( N ) Moments (N-m)
Load Case FX FY FZ MX MY MZ
---------------------------------------------------------------------------
WEIGHT: 5000.0 5000.0 5000.0 2500.0 2500.0 2500.0
OPER: 5000.0 5000.0 5000.0 2500.0 2500.0 2500.0
Solution Data
Case # FX FY FZ
1 395909. 241849. 0.
2 395909. 241849. 0.
3 51255506. 0. 0.
4 0. 4. 0.
5 0. 0. -5.
6 0. 0. 0.
7 395909. 241849. 0.
Notes:
Page 4
RESULT.txt
3) S1+S2+S3 < 4S (SUS,S1+S2+S3) Case 1
Pad/Header at Junction
Branch at Junction
Branch Transition
Page 6
RESULT.txt
Page 8
RESULT.txt
Material Name = SA-106B Carbon steel Smls. pipe
Material ID ............. 1008218
Cold Allowable ........... 118. MPa
Cold Elasic Modulus ...... 203000. MPa
Cold Yield Stress ........ 241. MPa
Hot Allowable @ 21 deg .. 118. MPa
Hot Yield Stress ......... 233. MPa
Hot Elastic Modulus ...... 203000. MPa
Case 1
Pressure Stress (Pd/2t) .. 8. MPa
Case 2
Pressure Stress (Pd/2t) .. 8. MPa
Case 3
Nominal Stress (M/Z) ... 4935. MPa
Case 4
Nominal Stress (M/Z) ... 79. MPa
Case 5
Nominal Stress (M/Z) ... 79. MPa
Case 6
Nominal Stress (M/Z) ... 79. MPa
Case 7
Nominal Stress (M/Z) ... 8. MPa
Smallest Thickness ....... 12.700 mm.
Stress Concentration ..... 1.000
Page 10
RESULT.txt
- SECONDARY (PL+PB+Q) STRESS has no direct equal in a B31 code.
This stress requirement is intended to insure that sig-
nificant inelastic behavior only occurs for the first few
loading cycles, and only over a fairly small region of the
model. "Small" is on the order of the square root of Rt,
where (R) is the radius of the header and (t) is the
thickness of the header. Secondary stresses do not include
the effect of peak stress concentration factors such as occur
at fillets, welds or notches.
Page 12
RESULT.txt
*** NO OVERSTRESSED NODES IN THIS MODEL ***
Pad/Header at Junction
Branch at Junction
Branch Transition
Page 13
RESULT.txt
Pad/Header at Junction
Branch at Junction
Branch Transition
Pad/Header at Junction
Branch at Junction
Page 15
RESULT.txt
Pl+Pb+Q+F Sa Primary+Secondary+Peak (Inner) Load Case 2
7 290 Stress Concentration Factor = 1.350
MPa MPa Strain Concentration Factor = 1.000
Cycles Allowed for this Stress = 1.0000E11
2% "B31" Fatigue Stress Allowable = 294.8
Markl Fatigue Stress Allowable = 287.5
WRC 474 Mean Cycles to Failure = 6.1222E9
WRC 474 99% Probability Cycles = 1.4222E9
WRC 474 95% Probability Cycles = 1.9746E9
BS5500 Allowed Cycles(Curve F) = 1.0192E10
Membrane-to-Bending Ratio = 2.880
Bending-to-PL+PB+Q Ratio = 0.258
Sect VIII Ref: 4-112(l)(2),Fig.4-130.1,4-135
Plot Reference:
6) Pl+Pb+Q+F < Sa (EXP,Inside) Case 2
Branch Transition
Page 16
RESULT.txt
Pl+Pb+Q+F Sa Primary+Secondary+Peak (Outer) Load Case 2
7 290 Stress Concentration Factor = 1.350
MPa MPa Strain Concentration Factor = 1.000
Cycles Allowed for this Stress = 1.0000E11
2% "B31" Fatigue Stress Allowable = 286.2
Markl Fatigue Stress Allowable = 287.5
WRC 474 Mean Cycles to Failure = 9.1894E9
WRC 474 99% Probability Cycles = 2.1348E9
WRC 474 95% Probability Cycles = 2.9639E9
BS5500 Allowed Cycles(Curve F) = 1.1574E10
Membrane-to-Bending Ratio = 2.226
Bending-to-PL+PB+Q Ratio = 0.310
Sect VIII Ref: 4-112(l)(2),Fig.4-130.1,4-135
Plot Reference:
7) Pl+Pb+Q+F < Sa (EXP,Outside) Case 2
Pad/Header at Junction
Page 17
RESULT.txt
Pl 1.5(k)Smh Primary Membrane Load Case 1
8 172 Sect VIII Ref: AD-140, 4-112(i), 4-133,
MPa MPa Fig. 4-130.1, Table 4-120.1
Plot Reference:
4% 1) Pl < 1.5(k)Smh (SUS,Membrane) Case 1
1%
2%
2%
Branch at Junction
1%
2%
2%
Branch Transition
Page 21
RESULT.txt
0%
0%
0%
2%
Page 23
RESULT.txt
2%
1%
2%
Page 25
RESULT.txt
2%
0%
Pad/Header at Junction
Pad/Header at Junction
Pad/Header at Junction
1%
Page 27
RESULT.txt
Pad Outer Edge Weld
2%
Page 28
RESULT.txt
Qb 3(Smh) Primary Bending Load Case 1
0 344 Sect VIII Ref: 4-112(h)(2), Table 4-120.1,
MPa MPa Fig.4-130.1, 4-133
Plot Reference:
0% 2) Qb < 3(Smh) (SUS,Bending) Case 1
2%
Branch at Junction
Branch at Junction
Branch at Junction
1%
Branch Transition
Page 29
RESULT.txt
FE/Pipe Version 7.0 Jobname: NOZZLE Page 27
Released Jul 2014 7:08pm FEB 27,2017
Branch Transition
Branch Transition
0%
Pad/Header at Junction
Pad/Header at Junction
Pad/Header at Junction
Pad/Header at Junction
Pad/Header at Junction
2%
Pad/Header at Junction
2%
Page 32
RESULT.txt
Pad Outer Edge Weld
Page 33
RESULT.txt
Pad Outer Edge Weld
2%
1%
Page 34
RESULT.txt
Pl+Pb+Q+F Sa Primary+Secondary+Peak (Inner) Load Case 2
4 290 Stress Concentration Factor = 1.000
MPa MPa Strain Concentration Factor = 1.000
Cycles Allowed for this Stress = 1.0000E11
1% "B31" Fatigue Stress Allowable = 286.2
Markl Fatigue Stress Allowable = 287.5
WRC 474 Mean Cycles to Failure = 1.8353E10
WRC 474 99% Probability Cycles = 4.2636E9
WRC 474 95% Probability Cycles = 5.9195E9
BS5500 Allowed Cycles(Curve F) = 3.6122E10
Membrane-to-Bending Ratio = 16.536
Bending-to-PL+PB+Q Ratio = 0.057
Sect VIII Ref: 4-112(l)(2),Fig.4-130.1,4-135
Plot Reference:
6) Pl+Pb+Q+F < Sa (EXP,Inside) Case 2
2%
0%
Branch at Junction
Branch at Junction
Branch at Junction
Branch at Junction
Branch at Junction
2%
Branch at Junction
2%
Branch Transition
Branch Transition
Branch Transition
Branch Transition
Page 38
RESULT.txt
Branch Transition
0%
Branch Transition
0%
B31.3 (Branch)
Peak Stress Sif .... 0.000 Axial
72.807 Inplane
96.547 Outplane
1.000 Torsional
B31.1 (Branch)
Page 40
RESULT.txt
Peak Stress Sif .... 0.000 Axial
96.547 Inplane
96.547 Outplane
96.547 Torsional
WRC 330 (Branch)
Peak Stress Sif .... 0.000 Axial
60.817 Inplane
96.547 Outplane
60.817 Torsional
NOTES:
Page 41
RESULT.txt
2) The Conservative Allowable Simultaneous loads are
the maximum loads that can be applied simultaneously.
A conservative stress combination equation is used
that typically produces stresses within 50-70% of the
allowable stress.
Page 43