Vous êtes sur la page 1sur 6

Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500

Series TY-FRB 5.6 K-factor


Horizontal and Vertical Sidewall Sprinklers
Quick Response, Standard Coverage
provided by the Recessed Escutcheon
General reduces the accuracy to which the
fixed pipe nipples to the sprinklers
Description must be cut.
The Series TY-FRB, 5.6 K-Factor, Hori- Corrosion resistant coatings, where
zontal and Vertical Sidewall Sprinklers applicable, are utilized to extend the
described in this data sheet are quick life of copper alloy sprinklers beyond
response - standard coverage, deco- that which would otherwise be ob-
rative 3 mm glass bulb type spray tained when exposed to corrosive at-
sprinklers designed for use in light and mospheres. Although corrosion resis-
ordinary hazard, commercial occupan- tant coated sprinklers have passed the
cies such as banks, hotels, shopping standard corrosion tests of the appli-
malls, etc. They are designed for instal- cable approval agencies, the testing is
lation along a wall or the side of a beam not representative of all possible cor-
and just beneath a smooth ceiling. rosive atmospheres. Consequently, it
Sidewall sprinklers are commonly is recommended that the end user be
used instead of pendent or upright consulted with respect to the suitability
sprinklers due to aesthetics or building of these coatings for any given corro-
construction considerations, where sive environment. The effects of ambi-
piping across the ceiling is not desir- ent temperature, concentration of
able. chemicals, and gas/chemical velocity,
should be considered, as a minimum,
The recessed version of the Series along with the corrosive nature of the
TY-FRB Horizontal Sidewall Sprinkler chemical to which the sprinklers will be
is intended for use in areas with a exposed.
finished wall. It uses a two-piece Style
10 Recessed Escutcheon with 1/2 inch WARNINGS
(12,7 mm) of recessed adjustment or The Series TY-FRB Sprinklers de-
up to 3/4 inch (19,1 mm) of total adjust- scribed herein must be installed and
ment from the flush sidewall position, maintained in compliance with this
or a two-piece Style 20 Recessed Es-
cutcheon with 1/4 inch (6,4 mm) of
document, as well as with the applica-
ble standards of the National Fire Pro- Technical
recessed adjustment or up to 1/2 inch
(12,7 mm) of total adjustment from the
tection Association, in addition to the
standards of any other authorities hav- Data
flush sidewall position. The adjustment ing jurisdiction. Failure to do so may Approvals
impair the performance of these de- UL and C-UL Listed.
vices. FM, LPCB, and NYC Approved.
The owner is responsible for maintain- (Refer to Table A for complete approval
ing their fire protection system and de- information including corrosion resis-
vices in proper operating condition. tant status.)
IMPORTANT The installing contractor or sprinkler
DuPont Registered Trademark

Always refer to Technical Data Maximum Working Pressure


manufacturer should be contacted 175 psi (12,1 bar)
Sheet TFP700 for the INSTALLER with any questions.
WARNING that provides cautions Discharge Coefficient
with respect to handling and instal- K = 5.6 GPM/psi1/2 (80,6 LPM/bar1/2)
lation of sprinkler systems and com-
ponents. Improper handling and in-
Model/Sprinkler Temperature Ratings
stallation can permanently damage
a sprinkler system or its compo-
Identification Refer to Table A
Finishes
nents and cause the sprinkler to fail
to operate in a fire situation or cause
Numbers Sprinkler: Refer to Table A
Recessed Escutcheon: White Coated,
it to operate prematurely. TY3331 - Horizontal Chrome Plated, or Brass Plated
TY3431 - Vertical

Page 1 of 6 JULY, 2004 TFP176


Page 2 of 6 TFP176

SPRINKLER FINISH (See Note 11)


K TYPE TEMP. BULB NATURAL CHROME WHITE*** LEAD
LIQUID BRASS PLATED POLYESTER COATED

135F/57C Orange
HORIZ.
155F/68C Red
SIDEWALL 1, 2, 3, 4, 9, 10 1, 2, 3, 9 1, 2, 3, 9
(TY3331) 175F/79C Yellow
200F/93C Green
5.6
286F/141C Blue
1/2"
NPT RECESSED 135F/57C Orange
HORIZ.
155F/68C Red
SIDEWALL 1, 2, 4, 9, 10 1, 2, 9 N/A
(TY3331)* 175F/79C Yellow
Figure 3
200F/93C Green
RECESSED 135F/57C Orange
HORIZ.
155F/68C Red
SIDEWALL 1, 2, 3, 4, 9 N/A
(TY3331)** 175F/79C Yellow
Figure 4
200F/93C Green
VERTICAL 135F/57C Orange
SIDEWALL
155F/68C Red
5.6 (TY3431) 5, 6, 7, 8, 9 5, 6, 7, 9
1/2" Installed 175F/79C Yellow
NPT Pendent
200F/93C Green
or
Upright 286F/141C Blue

NOTES:
1. Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers for use in Light and Ordinary Hazard Occupancies at a
4 to 12 inch (100 to 300 mm) top of deflector to ceiling distance.
2. Listed by Underwriters Laboratories Inc. for use in Canada (C-UL) as Quick Response Sprinklers for use in Light and Ordinary
Hazard Occupancies at a 4 to 12 inch (100 to 300 mm) top of deflector to ceiling distance.
3. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers for use in Light Hazard Occupancies at a
4 to 12 inch (100 to 300 mm) top of deflector to ceiling distance.
4. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 007a/04) at a 4 to 6 inch (100 to 150 mm) top of
deflector to ceiling distance. The LPC does not rate the thermal sensitivity of horizontal sidewall sprinklers.
5. Listed by Underwriters Laboratories, Inc. as Quick Response Sprinklers for use in Light and Ordinary Hazard Occupancies.
6. Listed by Underwriters Laboratories for use in Canada (C-UL) as Quick Response Sprinklers for use in Light and Ordinary Hazard
Occupancies.
7. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers for use in Light Hazard Occupancies.
8. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094a/06 & 007a/04) as Quick Response Sprinklers.
9. Approved by the City of New York under MEA 354-01-E.
10. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094a/06) at a 4 to 6 inch (100 to 150 mm) top of
deflector to ceiling distance. The LPC does not rate the thermal sensitivity of horizontal sidewall sprinklers.
11. Where Polyester Coated and Lead Coated Sprinklers are noted to be UL and C-UL Listed, the sprinklers are UL and C-UL Listed
as Corrosion Resistant Sprinklers. Where Lead Coated Sprinklers are noted to be FM Approved, the sprinklers are FM Approved as
Corrosion Resistant Sprinklers.
* Installed with Style 10 (1/2" NPT) 3/4" Total Adjustment Recessed Escutcheon.
** Installed with Style 20 (1/2" NPT) 1/2" Total Adjustment Recessed Escutcheon.
*** Frame and deflector only. Listings and approvals apply to color (Special Order).
TABLE A
LABORATORY LISTINGS AND APPROVALS

Physical Characteristics
Frame . . . . . . . . . . . . . Bronze Operation
Button . . . . . . . . . Brass/Copper
Sealing Assembly . . . . . . . . . . The glass Bulb contains a fluid which
. . . . . Beryllium Nickel w/Teflon expands when exposed to heat. When
Bulb . . . . . . . . . . . . . . . Glass the rated temperature is reached, the
Compression Screw . . . . . Bronze fluid expands sufficiently to shatter the
HSW Deflector . . . . . . . . Bronze glass Bulb, allowing the sprinkler to
VSW Deflector . . . . . . . . Copper activate and water to flow.
Patents
U.S.A. 5,810,263
TFP176 Page 3 of 6

Design DEFLECTOR
HAT 5
Criteria
The Series TY-FRB Horizontal and
Vertical Sidewall Sprinklers are in-
tended for fire protection systems de-
signed in accordance with the stand-
ard installation rules recognized by the 6* 4 2 3 1
applicable Listing or Approval agency
(e.g., UL Listing is based on the re- 9/16" WRENCH 1/2" **
quirements of NFPA 13, and FM Ap- (14,3 mm) FLATS NPT
proval is based on the requirements of
FMs Loss Prevention Data Sheets).
Only the Style 10 or 20 Recessed Es-
cutcheon, as applicable, is to be used
for recessed horizontal installations.

Installation 1-13/16"
(46,0 mm)
7/16"
(11,1 mm)
The Series TY-FRB Sprinklers must be NOMINAL
CENTERLINE
installed in accordance with the follow- OF SPRINKLER MAKE-IN
ing instructions: WATERWAY
1-1/2"
NOTES (38,1 mm)
Do not install any bulb type sprinkler if
the bulb is cracked or there is a loss of 2-3/16"
liquid from the bulb. With the sprinkler (55,6 mm)
held horizontally, a small air bubble STYLE ESCUTCHEON
should be present. The diameter of the 10 or 20 PLATE SEATING
air bubble is approximately 1/16 inch RECESSED SURFACE
(1,6 mm) for the 135F/57C to 3/32 ESCUTCHEON
inch (2,4 mm) for the 286F/141C 1 - Frame
temperature ratings. 2 - Button
3 - Sealing
A leak tight 1/2 inch NPT sprinkler joint Assembly
2-7/8" DIA.
should be obtained with a torque of 7 4 - Bulb
5 - Compression (73,0 mm)
to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi- Screw
mum of 21 ft. lbs. (28,5 Nm) of torque 6 - Deflector
may be used to install sprinklers with
1/2 NPT connections. Higher levels of
torque may distort the sprinkler and
cause leakage or impairment of the
sprinkler.
Do not attempt to make-up for insuffi- * Temperature rating is indicated on deflector or adjacent to orifice seat on frame.
cient adjustment in the escutcheon ** Pipe thread connections per ISO 7/1 can be provided on special request.
plate by under- or over-tightening the
sprinkler. Readjust the position of the FIGURE 1
sprinkler fitting to suit. 5.6 K-FACTOR QUICK RESPONSE
SERIES TY-FRB HORIZONTAL SIDEWALL (TY3331) SPRINKLERS
The Series TY-FRB Horizontal and
Vertical Sidewall Sprinklers must be
installed in accordance with the follow-
ing instructions. Step 3. Tighten the sprinkler into the word TOP on the Deflector is to face
sprinkler fitting using only the W-Type towards the ceiling.
Step 1. Horizontal sidewall sprinklers 6 Sprinkler Wrench (Ref. Figure 5),
are to be installed in the horizontal Step B. After installing the Style 10 or
With reference to Figure 1 or 2, the
position with their centerline of water- 20 Mounting Plate over the sprinkler
W-Type 6 Sprinkler Wrench is to be
way perpendicular to the back wall and threads, hand tighten the sprinkler into
applied to the wrench flats.
parallel to the ceiling. The word TOP the sprinkler fitting.
on the Deflector is to face towards the The Series TY-FRB Recessed Hori-
Step C. Tighten the sprinkler into the
ceiling. zontal Sidewall Sprinklers must be
sprinkler fitting using only the W-Type
installed in accordance with the follow-
Vertical sidewall sprinklers are to be 7 Recessed Sprinkler Wrench (Ref.
ing instructions.
installed in the pendent or upright po- Figure 6). With reference to Figure 1,
sition with the arrow on the Deflector Step A. Recessed horizontal sidewall the W-Type 7 Recessed Sprinkler
pointing away from the wall. sprinklers are to be installed in the Wrench is to be applied to the sprinkler
horizontal position with their centerline wrench flats.
Step 2. With pipe thread sealant ap- of waterway perpendicular to the back
plied to the pipe threads, hand tighten Step D. After the ceiling has been in-
wall and parallel to the ceiling. The
the sprinkler into the sprinkler fitting. stalled or the finish coat has been ap-
Page 4 of 6 TFP176

plied, slide on the Style 10 or 20 Clo-


sure over the Series TY-FRB Sprinkler ARROW MUST
and push the Closure over the Mount- POINT AWAY
ing Plate until its flange comes in con- 7/16" FROM AND BE
tact with the ceiling ESCUTCHEON (11,1 mm) PERPENDICULAR
PLATE SEATING NOMINAL TO THE BACK
SURFACE 1/2" ** MAKE-IN WALL SURFACE
Care and NPT
*6
Maintenance
5
The Series TY-BFR Sprinklers must be 2-3/16" 2-3/16"
maintained and serviced in accord- (55,6 mm) (55,6 mm) 4
ance with the following instructions:
1-1/2" WRENCH 2
NOTES (38,1 mm) FLATS
Before closing a fire protection system 7 3
main control valve for maintenance
work on the fire protection system that 1
it controls, permission to shut down the
affected fire protection system must be SHOWN SHOWN CROSS
obtained from the proper authorities PENDENT UPRIGHT SECTION
and all personnel who may be affected
by this action must be notified.
1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector
Absence of an escutcheon, which is 2 - Button Assembly 5 - Compression 7- Ejection Spring
used to cover a clearance hole, may Screw
delay the time to sprinkler operation in
a fire situation.
* Temperature rating is indicated on deflector or adjacent to orifice seat on frame.
Sprinklers that are found to be leaking ** Pipe thread connections per ISO 7/1 can be provided on special request.
or exhibiting visible signs of corrosion
must be replaced.
FIGURE 2
Automatic sprinklers must never be 5.6 K-FACTOR QUICK RESPONSE
painted, plated, coated or otherwise SERIES TY-FRB VERTICAL SIDEWALL (TY3431) SPRINKLERS
altered after leaving the factory. Modi-
fied sprinklers must be replaced.
Sprinklers that have been exposed to
corrosive products of combustion, but
have not operated, should be replaced
if they cannot be completely cleaned spection, testing, and maintenance of ment by Tyco Fire Products. No war-
by wiping the sprinkler with a cloth or their fire protection system and de- ranty is given for products or compo-
by brushing it with a soft bristle brush. vices in compliance with this docu- nents manufactured by companies not
ment, as well as with the applicable affiliated by ownership with Tyco Fire
Care must be exercised to avoid dam- standards of the National Fire Protec- Products or for products and compo-
age to the sprinklers - before, during, tion Association (e.g., NFPA 25), in nents which have been subject to mis-
and after installation. Sprinklers dam- addition to the standards of any other use, improper installation, corrosion,
aged by dropping, striking, wrench authorities having jurisdiction. The in- or which have not been installed, main-
twist/slippage, or the like, must be re- stalling contractor or sprinkler manu- tained, modified or repaired in accord-
placed. Also, replace any sprinkler that facturer should be contacted relative to ance with applicable Standards of the
has a cracked bulb or that has lost any questions. National Fire Protection Association,
liquid from its bulb. (Ref. Installation and/or the standards of any other
Section). It is recommended that automatic
Authorities Having Jurisdiction. Mate-
sprinkler systems be inspected,
Frequent visual inspections are rec- rials found by Tyco Fire Products to be
tested, and maintained by a qualified
ommended to be initially performed for defective shall be either repaired or
Inspection Service in accordance with
corrosion resistant coated sprinklers, replaced, at Tyco Fire Products sole
local requirements and/or national
after the installation has been com- option. Tyco Fire Products neither as-
codes.
pleted, to verify the integrity of the cor- sumes, nor authorizes any person to
rosion resistant coating. Thereafter, assume for it, any other obligation in
annual inspections per NFPA 25
should suffice; however, instead of in-
Limited connection with the sale of products or
parts of products. Tyco Fire Products
specting from the floor level, a random
sampling of close-up visual inspec-
Warranty shall not be responsible for sprinkler
system design errors or inaccurate or
tions should be made, so as to better Products manufactured by Tyco Fire incomplete information supplied by
determine the exact sprinkler condi- Products are warranted solely to the Buyer or Buyers representatives.
tion and the long term integrity of the original Buyer for ten (10) years IN NO EVENT SHALL TYCO FIRE
corrosion resistant coating, as it may against defects in material and work- PRODUCTS BE LIABLE, IN CON-
be affected by the corrosive conditions manship when paid for and properly TRACT, TORT, STRICT LIABILITY OR
present. installed and maintained under normal UNDER ANY OTHER LEGAL THE-
use and service. This warranty will ex- ORY, FOR INCIDENTAL, INDIRECT,
The owner is responsible for the in- pire ten (10) years from date of ship- SPECIAL OR CONSEQUENTIAL
TFP176 Page 5 of 6

5/81/4"
(15,96,4 mm)
WRENCH RECESS
FACE OF
MOUNTING (END "A" USED FOR
SPRINKLER 1/2" NPT MODELS)
SURFACE
FITTING

FIGURE 5
CLOSURE W-TYPE 6 SPRINKLER WRENCH

2-7/8" DIA.
(73,0 mm) WRENCH
SERIES RECESS
TY-FRB 2-1/4" DIA.
(57,2 mm)

MOUNTING
PLATE

1/8" PUSH WRENCH


(3,2 mm) IN TO ENSURE
ENGAGEMENT
1-1/4" (31,8 mm) 3/4" (19,1 mm) WITH SPRINKLER
WRENCHING AREA
3/4" (19,1 mm) 1/4" (6,4 mm)

FIGURE 3 FIGURE 6
SERIES TY-FRB RECESSED HORIZONTAL SIDEWALL SPRINKLER W-TYPE 7 RECESSED
WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT SPRINKLER WRENCH
STYLE 10 RECESSED ESCUTCHEON

1/21/8"
(12,73,2 mm) DAMAGES, INCLUDING BUT NOT
LIMITED TO LABOR CHARGES, RE-
FACE OF GARDLESS OF WHETHER TYCO
MOUNTING FIRE PRODUCTS WAS INFORMED
SPRINKLER
SURFACE ABOUT THE POSSIBILITY OF SUCH
FITTING
DAMAGES, AND IN NO EVENT
SHALL TYCO FIRE PRODUCTS LI-
ABILITY EXCEED AN AMOUNT
CLOSURE EQUAL TO THE SALES PRICE.
THE FOREGOING WARRANTY IS
2-7/8" DIA. MADE IN LIEU OF ANY AND ALL
(73,0 mm) OTHER WARRANTIES EXPRESS OR
SERIES IMPLIED, INCLUDING WARRANTIES
TY-FRB 2-1/4" DIA.
(57,2 mm)
OF MERCHANTABILITY AND FIT-
NESS FOR A PARTICULAR PUR-
POSE.
MOUNTING
PLATE

1/8"
(3,2 mm)

1-1/4" (31,8 mm) 1/2" (12,7 mm)


1" (25,4 mm) 1/4" (6,4 mm)

FIGURE 4
SERIES TY-FRB RECESSED HORIZONTAL SIDEWALL SPRINKLER
WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 20 RECESSED ESCUTCHEON
Page 6 of 6 TFP176

P/N 57 XXX X XXX


SPRINKLER TEMPERATURE
MODEL/SIN RATING

378 HORIZONTAL SIDEWALL TY3331 1 NATURAL BRASS 135 135F/57C

375 VERTICAL SIDEWALL TY3431 4 WHITE POLYESTER 155 155F/68C

3 WHITE RAL9010)* 175 175F/79C

9 CHROME PLATED 200 200F/93C

7 LEAD COATED 286 286F/141C

TABLE B * Eastern Hemisphere sales only.


PART NUMBER SELECTION
SERIES TY-FRB HORIZONTAL AND VERTICAL SIDEWALL SPRINKLERS

Ordering
Procedure
When placing an order, indicate the full Recessed Escutcheon:
product name. Refer to the Price List Specify: Style (specify) Recessed Es-
for complete listing of Part Numbers. cutcheon with (specify finish), P/N
Contact your local distributor for avail- (specify).
ability.
1/2" (15 mm)
Style 10
Sprinkler Assemblies with NPT Chrome Plated . . . . . . . . . P/N 56-701-9-010
Thread Connections: 1/2" (15 mm)
Specify: (Specify Model/SIN), Quick Style 10
White Color
Response, (specify K-factor), (specify Coated . . . . . . . . . . . . . . . P/N 56-701-4-010
temperature rating), Series TY-FRB 1/2" (15 mm)
(specify Horizontal Sidewall or Vertical Style 10
Sidewall) Sprinkler with (specify type White RAL9010* . . . . . . . P/N 56-701-3-010
of finish or coating), P/N (specify from 1/2" (15 mm)
Style 10
Table B). Brass Plated . . . . . . . . . . . P/N 56-701-2-010
1/2" (15 mm)
Style 20
Chrome Plated . . . . . . . . . P/N 56-705-9-010
1/2" (15 mm)
Style 20
White Color
Coated . . . . . . . . . . . . . . . P/N 56-705-4-010
1/2" (15 mm)
Style 20
White RAL9010* . . . . . . . P/N 56-705-3-010
1/2" (15 mm)
Style 20
Brass Plated . . . . . . . . . . . P/N 56-705-2-010

* Eastern Hemisphere sales only.

Sprinkler Wrench:
Specify: W-Type 6 Sprinkler Wrench,
P/N 56-000-6-387.
Specify: W-Type 7 Sprinkler Wrench,
P/N 56-850-4-001.

TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446

Vous aimerez peut-être aussi