Académique Documents
Professionnel Documents
Culture Documents
Table of Contents
Unpacking......................................................................3
Introduction....................................................................3
Customer Support......................................................................3
Safety Precautions......................................................................4
General Information.....................................................................5
Features.........................................................................5
Registration......................................................................5
Mounting.........................................................................6
Controls and Functions..............................................................8
DMX Set-Up................................................................................8
System Menu............................................................................14
Editing Program.........................................................................32
Error Codes...............................................................................35
Operating Modes.......................................................................37
DMX Traits.................................................................................39
Changing the Gobo...................................................................45
Photometric Chart.....................................................................47
Fuse Replacement....................................................................48
Cleaning..................................................................48
Trouble Shooting.......................................................................48
Warranty.................................................................49
Specifications....................................................................51
User Instructions
Rev. 8/10 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 2
Vizi LED Spot Introduction Vizi LED Spot Safety Precautions
Unpacking: Thank you for purchasing the Vizi LED Spot by Ameri- For Your Own Personal Safety, Please Read and Understand This
can DJ. Every Vizi LED Spot has been thoroughly tested and has Manual Completely Before You Attempt To Install Or Operate
been shipped in perfect operating condition. Carefully check the ship- This Unit!
ping carton for damage that may have occurred during shipping. If the To reduce the risk of electrical shock or fire, do not expose this unit
carton appears to be damaged, carefully inspect your fixture for any rain or moisture
damage and be sure all equipment necessary to operate the unit has Do not spill water or other liquids into or on to your unit.
arrived intact. In the event damage has been found or parts are miss- Be sure that the local power outlet match that of the required volt-
ing, please contact our toll free customer support number for further age for your unit.
instructions. Please do not return this unit to your dealer without con- Do not attempt to operate this unit if the power cord has been
tacting customer support first. frayed or broken.
Introduction: The Vizi LED Spot is a compact, bright, moving head, Do not attempt to remove or break off the ground prong from
DMX intelligent fixture. The Vizi LED Spot can be either a 10 or 12 the electrical cord. This prong is used to reduce the risk of electrical
Channel DMX unit. The fixture can operate in three different operat- shock and fire in case of an internal short.
ing modes; show mode, sound-active, or under DMX Control. The Vizi Disconnect from main power before making any type of connection.
LED Spot can be used as a stand alone unit or in a master/slave con- Do not remove the cover under any conditions. There are no user
figuration. For best results use fog or special effects smoke to enhance serviceable parts inside.
the beams projections. Never operate this unit when its cover is removed.
Always be sure to mount this unit in an area that will allow proper
Customer Support: American DJ provides a toll free customer ventilation. Allow about 6 (15cm) between this device and a wall.
support line, to provide help and to answer any question should you Do not attempt to operate this unit, if it becomes damaged.
encounter problems during your set up or initial operation. You may This unit is intended for indoor use only, use of this product out-
also visit us on the web at www.americandj.com for any comments or doors voids all warranties.
suggestions. Service Hours are Monday through Friday 9:00 a.m. to Always mount this unit in safe and stable matter.
4:30 p.m. Pacific Standard Time. Power-supply cords should be routed so that they are not likely to
Voice: (800) 322-6337 be walked on or pinched by items placed upon or against them,
Fax: (323) 582-2941 paying particular attention to cords at plugs, convenience recep-
E-mail: support@americandj.com tacles, and the point where they exit from the appliance.
To purchase parts online visit http://parts.americandj.com Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 48 for cleaning details.
Warning! To prevent or reduce the risk of electrical shock or fire, do Heat -This fixture should be situated away from heat sources such
not expose this unit to rain or moisture.
as radiators, heat registers, stoves, or other appliances (including
Warning! This may cause severe eye damage. Avoid looking directly amplifiers) that produce heat.
into the light source at all times! The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a
marked change in performance.
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 3 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 4
Vizi LED Spot General Information Vizi LED Spot Mounting
To optimize the performance of this product, please read these operating When installing the unit, the trussing or area of installation must be
instructions carefully to familiarize yourself with the basic operations of able to hold 10 times the weight without any deformation. When
this unit. These instructions contain important safety information regard- installing the unit must be secured with a secondary safety attach-
ing the use and maintenance of this unit. Please keep this manual with ment, e.g. and appropriate safety cable. Never stand directly below
the unit, for future reference. the unit when mounting, removing, or servicing the unit.
American DJ will not accept any liability for any resulting damages Overhead mounting requires extensive experience, including calculat-
caused by the non-observance of this manual or any unauthorized ing working load limits, installation material being used, and perodic
modification to this unit. safety inspection of all installation material and unit. If you lack these
qualifications, do not attempt the installation yourself.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures war- These installaiton should be checked by a skilled person once a year.
ranty. In the unlikely event your unit may require service please contact
American DJ.
Vizi LED Spot Features
DMX-512 Protocol Compatible (Uses either 10 or 12 DMX
Channels)
3 Operating Modes - Sound Active, Show Mode, DMX Control
Internal Microphone
Edit and Save Scenes into the Memory
Variable Strobe (1-12 fps)
Switchable 540 to 630 Pan Movement
270 Tilt Movement
Digital Display for Address and Function Setting
Vizi LED Spot Product Registration
The Vizi LED Spot carries a three year (1095 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase.
All returned service items whether under warranty or not, must be
freight pre-paid and accompany a return authorization (R.A.) number.
The R.A. number must be clearly written on the outside of the return The Vizi LED Spot is fully operational in three different mounting posi-
package. A brief description of the problem as well as the R.A. num- tions, hanging upside-down from a ceiling, side mounted, or set on a
ber must also be written down on a piece of paper and included in the flat level surface. To avoid internal damage to the unit, never mount
shipping carton. If the unit is under warranty, you must provide a copy the unit on its side as illustrated above. Be sure this fixture is kept
of your proof of purchase invoice. You may obtain a R.A. number by at least 0.5m away from any flammable materials (decoration etc.).
contacting our customer support team on our toll free customer sup- Always use and install the supplied safety cable as a safety measure
port number. All packages returned to the service department not dis- to prevent accidental damage and/or injury in the event the clamp
playing a R.A. number on the outside of the package will be returned fails (see next page). Never use the carrying handles for secondary
to the shipper at the shippers cost. attachment.
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 5 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 6
Vizi LED Spot Mounting Vizi LED Spot Controls and Functions
NOTICE: The suitable enviromental temperature for this light- FRONT
ing fixture is between -25 C to 45 C. Do not place this lighting
fixture in an enviroment where the temperatures are under or
above the temperatures stated above. This will allow the fixture
to run at its best and help prolong the fixture life.
REAR
Screw one clamp each via a M12 screw and nut onto the
Omega holders. Insert the quick-lock fasteners of the first
Omega holder into the respective holes on the bottom of the
Vizi LED Spot. Tighten the quick-lock fasteners fully clockwise.
Install the second Omega holder. Pull the safety-cable through
the holes on the bottom of the base and over the trussing
system or a safe fixation spot. Insert the end in the carabine
and tighten the safety screw.
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 7 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 8
Vizi LED Spot Controls and Functions Vizi LED Spot Controls and Functions
1. Lens Assembly - This high quality lens is a fully focusing. Focus unless otherwise told to do so by an authorized American DJ service
the lens by manually turning the lens in a clockwise or counter-clock- technician.
wise direction until the desired effect is achieved.
11. Power Switch - This switches the power to the fixutre On and
2. Digital Display - This display shows the menu and operating func- Off.
tions that you can choose from.
12. XLR Output Jack - This jack is used to transmit the incoming
3. Mode/ESC Button - This button is used to exit menus and to scroll DMX s ignal to another DMX fixture, or transmit a Master/Slave signal
backwards through certain menus only. to the next Vizi LED Spot in the chain. For best results in DMX or
Master/Slave mode terminate this jack if it is the last unit in the chain.
4. Up Button - This button is used to scroll forward when navigating
See Terminator on page 11.
through the system menu.
13. XLR DMX Input Jack - This jack is used to receive an incoming
5. Down Button - This button is used to scroll backwards when navi-
DMX s ignal or Master/Slave signal.
gating through the system menu.
6. Enter Button - This button is used to select and confirm a func-
tion when working in the system menu. It is also used to exit certain
menus.
7. Microphone - This microphone receives external low frequencies
to trigger the unit in Sound-Active mode. This microphone is designed
to receive low frequency sounds only, tapping on the microphone and
high pitch sounds may not trigger the unit.
8. Carrying Handles - The includes built-in carrying handles. Be sure
to always handle the unit by the built-in handles. Never lift or carry-
ing the unit by head or yoke. Pulling on or transporting the unit by the
moving head may severely damage the unit and will void the unit war-
ranty.
9. Power Cord Inlet - This cord is designed to match the electrical
requirements of the unit. Voltage may vary from venue to venue, when
connecting this unit to a power supply be sure to connect to a match-
ing power outlet. Never use this fixture if the ground prong has been
removed or broken off. The ground prong is designed to reduce the
risk of fire or electrical shock in the event the unit suffers from an inter-
nal short.
10. Fuse Holder - The fuse housing stores a 2 amp (1 amp 220v) pro-
tective fuse. Never defeat the fuse, the fuse is designed to protect the
electronics in the event of severe power fluctuations. Always be sure
to replace the fuse with an exact match as the one being replaced,
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 9 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 10
REMOTE INPUT OUTPUT REMOTE INPUT OUTPUT
Power Supply: Before plugging your unit in, be sure the source sound and lighting stores). Your cables should be made with a male
voltage in your area matches the required voltage for your American and female XLR connector on either end of the cable. Also remember
DJ Vizi LED Spot. This unit is available in a 120v and 220v version. that DMX cable must be daisy chained and cannot be split.
Because line voltage may vary from venue to venue, you should be
sure your unit voltage matches the wall outlet voltage before attempt- POWER POWER
tocol used by most lighting and controller manufactures as a form of nect the cables shield conductor to the ground lug or allow the shield
communication between intelligent fixtures and controllers. A DMX conductor to come in contact with the XLRs outer casing. Grounding
controller sends DMX data instructions from the controller to the fix- the shield could cause a short circuit and erratic behavior.
ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA IN and DATA OUT XLR terminals located on all DMX COMMON
Termination
fixtures (most controllers only have a DATA OUT terminal). DMX512 OUT
1
3
DMX +
3
1
DMX512 IN 3
1 avoids sign
and interfere
3-PIN XLR 2 DMX - 3-PIN XLR
2 2 to connect a
DMX Linking: DMX is a language allowing all makes and models Figure 2
120 Ohm 1/4
and PIN 3 (
of different manufactures to be linked together and operate from a
single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using XLR Male Socket XLR Female Socket XLR Pin Configuration
several DMX fixtures try to use the shortest cable path possible. The 1 Ground 2 Cold 2 Cold 1 Ground Pin 1 = Ground
order in which fixtures are connected in a DMX line does not influence
REMOTE INPUT OUTPUT REMOTE INPUT OUTPUT REMOTE INPUT OUTPUT
SOUND CONTROL SOUND CONTROL SOUND CONTROL
INPUT INPUT Pin 2INPUT
= Data Compliment (negative)
the DMX addressing. For example; a fixture assigned a DMX address 3 Hot 3 Hot Pin 3 = Data True (positive)
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled Figure 3
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
POWER
Special Note: Line Termination. When longer runs of cable are
POWER POWER
DATA assigned to address 1 to that unit, no matter where it is located used, you may need to use a terminator on the last unit to avoid erratic
in the DMX chain. behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-
DMX512
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
DMX+,DMX-,COMMON nected between pins 2 and 3 of a male XLR connector (DATA + and
Operation): The Vizi LED Spot can be controlled via DMX-512 pro- DATA -). This unit is inserted in the female XLR connector of the last
tocol. The Vizi LED Spot can be either a 10 or 12 unit in your daisy chain to terminate the line. Using a cable terminator
channel DMX unit. The DMX address is set elec- (ADJ part number Z-DMX/T) will decrease the possibilities of erratic
tronically using the controls on the side panel of behavior.
the unit. Your unit and your DMX controller require COMMON
Termination reduces signal errors and
a approved DMX-512 110 Ohm Data cable for data DMX512 OUT
3-PIN XLR
DMX + 1
3 3
1
DMX512 IN 3
1 avoids signal transmission problems
and interference. It is always advisable
DMX - 2 2 3-PIN XLR 2 to connect a DMX terminal, (Resistance
input and data output (Figure 1). We recommend 120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture. Figure 4
Accu-Cable DMX cables. If you are making your
own cables, be sure to use standard 110-120 Ohm Figure 1
shielded cable (This cable may be purchased at almost all professional
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 11 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 12
Vizi LED Spot Set Up Vizi LED Spot System Menu
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX 0 ADDR AXXX A001
Indicate the staring DMX address
A001 also is the setting for slave
fixtures may be implemented in a 3-pin DMX line. When inserting stan- 1 TEST T-01~T-XX Automatically test the function
RUN MSTR/ALON Runs fixture as master or alone for auto
dard 5-pin data cables in to a 3-pin line a cable adaptor must be used, Runs fixture as master or alone for
AUDI MSTR/ALON
these adaptors are readily available at most electric stores. The chart 2 PLAY audio
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 13 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 14
Vizi LED Spot System Menu Vizi LED Spot System Menu
ADDRESS MENU - RPAN (REVERSE PAN) MENU -
AOO1 - A511 (Value) - This is where you set the DMX address of ON/OFF - When On is chosen it will reverse the pan.
the unit.
RTILT (REVERSE TILT) MENU -
TEST MENU - ON/OFF - When On is chosen it will reverse the tilt.
T-01 - T-XX (Test) - Tests the functions of each channel.
FINE MENU -
Note: Some channels cannot be tested.
ON/OFF - Switch between 8bit (coarse) and 16bit (fine) pan & tilt
PLAY MENU - movement. This also switches the DMX channel mode between
RUN - Runs the unit as a master or in a stand alone mode. The 10 channel (8 bit) and 12 channel (16 bit) DMX mode.
unit will run a internal program mode.
DEGR MENU -
AUDI (Audio) - Runs the unit as a master or in a stand alone, 540/630 - Switch the degree of the Pan between 630 and 540.
sound active mode.
MIC MENU -
AUTO - This is a precaution mode in case the DMX signal is lost. M-01-M-70 - With this function you can make the internal mic
There are four settings to choose from: more or less sensitive to sound.
Hold - This is the default setting, which in case the signal is DISPLAY MENU -
lost the fixute will hold at the last setting. VALU (DMX-512 Value) - Display the DMX-512 value of each
Close - The fixture will return to its home standing. channel.
Auto - The fixture will go into Auto mode and run a pre-pro- D ON - Display will turn off in 2 minutes.
grammed show. FLIP - Flips the digital display 180.
Audi - The fixture will go into Sound Active mode. LOCK - When activated the buttons will lock automatically. See
page 25 for more information.
RESE (RESET) MENU -
ALL - Resets all the motors in the unit. SPEC MENU -
SCAN - Resets the motors that control pan/tilt. RDMX - Lets you adjust the DMX address via external controller.
COLR (Color) - Resets the color motors. SPOT - This provides a spot beam for better lamp optimization.
GOBO - Resets the gobo motors. DFSE (Default Settings) - Resets the unit to the default settings.
OTHR - Resets all other motors. FEED - Pan/Tilt feedback (error correction) on/off.
FANS - Select the fan running mode.
TIME MENU -
LIFE - Displays the fixtures total running time. VER (Version) - Displays the software version
CLMP - Clears the fixture running time. ADJU - Calibration functions
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 15 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 16
Vizi LED Spot System Menu Vizi LED Spot System Menu
EDIT MENU - On-Board System Menu. The Vizi LED Spot ccomes with an easy
SEPR (AUTO IP01 - IP07) - Lets you edit any of the 7 internal to navigate system menu. This next section will detail the functions of
programs. each command in the system menu.
STEP (S-01 - S-48) - These are the steps slots that you write To access the main menu press the MODE/ESC button (3) on the front
your programs into. There are at total of 48 steps. See edit pro- of the unit. Tap the UP (4) or DOWN (5) butons until you reach function
gram. you wish to change. When you reach the function you wish to change
tap the enter button. Again, tap the UP or down buttons to change
SCXX (SC01 - SC30) - These are the scenes that are stored in the function. Once your changes are made, tap the enter button to
your program. There are a total of 30 scenes. lock the change in the system, if the enter button is not selected
within eight seconds the system will automatically return to menu sec-
REC - This will auto save your custom program. tion. To exit without making any changes tap the MODE/ESC button.
RUN - This will run your custom program.
ADDR MAIN MENU -
ADDR DMX Address Setting via control board -
1. Access the main menu.
2. Tap the UP button until ADDR is displayed, press ENTER.
4. Now the display will show A001. Adjust the DMX address
by pressing the UP or DOWN buttons.
5. Press ENTER to confirm.
6. Press the MODE/ESC button to return to the main menu.
When the display is on A001, you can directly press the UP
or DN buttons to change the DMX start address.
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 17 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 18
Vizi LED Spot System Menu Vizi LED Spot System Menu
4. Press MODE/ESC to exit. AUDI. HOLD is the default setting.
5. Select the mode that you want the fixture to run in case of a
PLAY MAIN MENU - lost DMX signal and press ENTER.
RUN Run the unit in an Auto mode as a master in a
Master/Slave configuration, or as a stand alone unit - RESE MAIN MENU -
1. Access the main menu. ALL - When you activate the reset function, the fixture will
2. Tap the UP button until PLAY is displayed, press ENTER. begin the reset motion, reseting all motors.
3. Tap the UP button until RUN is displayed, press ENTER. 1. Access the main menu.
4. Tap the UP or DOWN button to choose between MSTR or 2. Tap the UP button until RESE is displayed, press ENTER.
ALON, select your choice by pressing ENTER, PASS will flash 3. Tap the UP button until ALL is displayed.
in the display and fixture will begin its function.
4. Press ENTER to reset all motors, or press MODE/ESC to
cancel and return to the main menu.
AUDI Run the unit in Sound Active mode as a master, or
as a stand alone unit - SCAN - When you activate this reset function, the fixture
will only reset the pan/tilt motor.
1. Access the main menu.
1. Access the main menu.
2. Tap the UP button until PLAY is displayed, press ENTER.
2. Tap the UP button until RESE is displayed, press ENTER.
3. Tap the UP button until AUDI is displayed, press ENTER.
3. Tap the UP button until SCAN is displayed.
4. Tap the UP or DOWN button to choose between MSTR or
ALON, select your choice by pressing ENTER, PASS will flash 4. Press ENTER to reset the pan/tilt motors, or press MODE/
in the display and fixture will begin its function. ESC to cancel and return to the main menu.
1. Access the main menu by pressing MODE/ESC button. 2. Tap the UP button until RESE is displayed, press ENTER.
2. Tap the UP button until PLAY is displayed, press ENTER. 3. Tap the UP button until COLR is displayed.
3. Tap the UP button until AUTO is displayed, press ENTER. 4. Press ENTER to reset the color wheel motor, or press MODE/
4. Now you can choose between CLOSE, HOLD AUTO, or ESC to cancel and return to the main menu.
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 19 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 20
Vizi LED Spot System Menu Vizi LED Spot System Menu
GOBO - When you activate this reset function, the fixture 2. Tap the UP button until TIME is displayed, press ENTER.
will only reset the gobo wheel motor. 3. Tap the UP button until CLMT is displayed, press ENTER.
1. Access the main menu by pressing MODE/ESC button. 4. Press ENTER to confirm.
2. Tap the UP button until RESE is displayed, press ENTER. 5. Press MODE/ESC to return to the main menu.
3. Tap the UP button until GOBO is displayed.
4. Press ENTER to reset the gobo wheel motor, or press MODE/ RPAN MENU -
ESC to cancel and return to the main menu. RPAN - The movement of the Pan will be reversed.
OTHR - When you activate this reset function, the fixture 1. Access the main menu.
will reset all other motors that are not listed in RESET 2. Tap the UP button until RPAN is displayed, press ENTER.
menu.
3. Press the UP or DOWN buttons to select either ON to acti-
1. Access the main menu by pressing MODE/ESC button. vate this function, or OFF to deactivate this function.
2. Tap the UP button until RESE is displayed, press ENTER. 4. Press ENTER to confirm.
3. Tap the UP button until OTHR is displayed. 5. Press MODE/ESC to return to the main menu.
4. Press ENTER to reset all other motors, or press MODE/ESC
to cancel and return to the main menu. RTILT MENU -
RTILT - The movement of the Tilt will be reversed.
TIME MAIN MENU -
1. Access the main menu.
LIFE - With this function you can display the total running 2. Tap the UP button until RTILT is displayed, press ENTER.
time of the unit.
3. Press the UP or DOWN buttons to select either ON to acti-
1. Access the main menu.
vate this function, or OFF to deactivate this function.
2. Tap the UP button until TIME is displayed, press ENTER.
4. Press ENTER to confirm.
3. Tap the UP button until LIFE is displayed, press ENTER.
5. Press MODE/ESC to return to the main menu.
4. Press MODE/ESC to return to the main menu.
CLMT - With this function you can clear the running time of
the unit.
1. Access the main menu.
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 21 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 22
Vizi LED Spot System Menu Vizi LED Spot System Menu
FINE MENU -
5. Press the UP or DOWN button to adjust the microphone sen-
FINE - Switch between 8bit (coarse) and 16bit (fine) pan & sitivity between M-01 - M-99.
tilt movement. This also switches the DMX Channel mode
between 10 channel (8 bit) and 12 channel (16 bit) DMX 6. Press ENTER to confirm when you have reached your
mode. desired microphone sesitivity level.
1. Access the main menu. 7. Press MODE/ESC to return to the main menu.
3. Tap the UP button until FINE is displayed, press ENTER.
DISP MAIN MENU -
4. Press the UP or DOWN buttons to select either ON to acti-
vate this function, or OFF to deactivate this function. VALU Display the DMX-512 value of each channel -
5. Press ENTER to confirm. 1. Access the main menu.
6. Press MODE/ESC to return to the main menu. 2. Tap the UP button until DISP is displayed, press ENTER.
3. Tap the UP button until VALU is displayed, press ENTER.
DEGR MENU - 4. The display should show D-00. Press the UP button in
DEGR - With this function you can switch the Pan degree. order to select the desired channel. If you select D-05 the
display will only show the DMX value of the 5th channel
1. Access the main menu.
5. Press ENTER to confirm.
2. Tap the UP button until DEGR is displayed, press ENTER.
6. Press MODE/ESC to return to the main menu.
3. Press the UP or DOWN buttons to select either 630 or
540. Now the display will change as per the 5th channel DMX
value.
4. Press ENTER to confirm your selection.
5. Press MODE/ESC to return to the main menu.
D ON With this function On the display will shut off after
2 minutes -
MIC MENU - 1. Access the main menu.
MIC - The internal microphone can be made more or less 2. Tap the UP button until DISP is displayed, press ENTER.
sensitive.
3. Tap the UP button until D ON is displayed, press ENTER.
1. Access the main menu.
4. Press the UP or DOWN buttons to select either ON to acti-
3. Tap the UP button until MIC is displayed, press ENTER. vate this function, or OFF to deactivate this function.
4. The display will show M-01.
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 23 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 24
Vizi LED Spot System Menu Vizi LED Spot System Menu
5. Press ENTER to confirm. to ON already.
1. Access the main menu by pressing MODE/ESC.
6. Press MODE/ESC to return to the main menu.
2. Tap the UP button until SPEC is displayed, press ENTER.
FLIP - This function will reverse the display 180. 3. Tap the UP button until RDNX is displayed, press ENTER.
1. Access the main menu. 4. Press the UP button to select ON to activate this function,
or OFF to deactivate.
2. Tap the UP button until DISP is displayed.
5. Press ENTER to confirm, and PASS will flash quickly.
3. Tap the UP button until FLIP is displayed, press ENTER.
6. Press MODE/ESC to return to the main menu.
4. Press the UP or DOWN buttons to select either ON to acti-
vate this function, or OFF to deactivate this function. To use this function follow the instructions:
To adjust the address of your unit you must first go to the
5. Press ENTER to confirm. address that it is currently set to. From there you can adjust the
6. Press MODE/ESC to return to the main menu. address. First make sure all channels are set to the value of 0.
1. On your DMX controller set the DMX value of Channel 1 to
LOCK - With this function you can activate the automatic the value 7.
button lock. When this function is activated, the buttons 2. Now set the DMX value of Channel 2 to the value 7 to
will automatically lock 15 seconds after the last press of adjust the starting address between 1 and 255. To adjust the
a button. In order to deactivate the button lock, press the address between 256 and 511 set Channel 2 to the value 8 .
MODE/ESC button for 3 seconds.
3. Set the DMX value of Channel 3 to your desired start-
1. Access the main menu. ing address. This will take about 20 seconds before the unit
2. Tap the UP button until DISP is displayed. accepts the new DMX address.
3. Tap the UP button until LOCK is displayed, press ENTER. EXAMPLE: So, if you want the address to be 57, you must first
set the address that is currently assingned to the unit. The pro-
4. Press the UP or DOWN buttons to select either ON to acti- ceed to set Channel 1s value to 7, Channel 2s value to 7,
vate this function, or OFF to deactivate this function. and Channel 3s value to 57.
5. Press ENTER to confirm. 2nd Example: Again, if you want the address to be 420, you
6. Press MODE/ESC to return to the main menu. must first set the address that is currently assingned to the unit.
If you want the set the address to 420, set Channel 1s value to
SPEC MAIN MENU - 7, Channel 2s value to 8, and Channel 3s to 164. (256 +
164 = 420)
RDMX With this function you are able to change the DMX
address via any DMX controller. This function is factory set SPOT - With this function you can adjust the LED via
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 25 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 26
Vizi LED Spot System Menu Vizi LED Spot System Menu
the control board. The shutter opens and the LED can be correction on and off. This will automatically correct the
adjusted. In this mode, the device will not react to any con- Pan/Tilt if it is somehow moved out of place.
trol signal. 1. Access the main menu.
1. Access the main menu. 2. Tap the UP button until SPEC is displayed, press ENTER.
2. Tap the UP button until SPEC is displayed, press ENTER. 3. Tap the UP button until FEED is displayed, press ENTER.
3. Tap the UP button until SPOT is displayed, press ENTER. 4. Press the UP or DOWN buttons to select either ON to acti-
4. The display will show ON/OFF. vate this function, or OFF to deactivate this function.
5. Press the UP button to select ON to activate this function, 5. Press ENTER to confirm.
or OFF to deactivate this function. 6. Press MODE/ESC to return to the main menu.
6. Press ENTER to confirm.
7. Press MODE/ESC to return to the main menu.
FANS - With this function you can choose between the fan
settings of Low, High or Auto. The default setting is Auto.
DFSE - With this function you can restore the factory 1. Access the main menu by pressing MODE/ESC button.
settings of the device. All settings will be set back to the 2. Tap the UP button until FANS is displayed, press ENTER.
default values. Any edited scenes will be lost. When restor-
ing the factory settings the unit must be set to the address 3. Press the UP or DOWN buttons to select either LOW, HIGH,
that the unit was in when you started editing. or AUTO.
1. Access the main menu. 4. Press ENTER to confirm your selection.
2. Tap the UP button until SPEC is displayed, press ENTER. 5. Press MODE/ESC to return to the main menu.
3. Tap the UP button until DFSE is displayed, press ENTER. VER - Use this function to display the Software version of
4. The display will show ON/OFF. the unit.
5. Press the UP button to display ON to activate this function, 1. Access the main menu.
or OFF to deactivate this function. 2. Tap the UP button until SPEC is displayed, press ENTER.
6. Press ENTER to confirm. 3. Tap the UP button until VER is displayed, press ENTER.
7. Press MODE/ESC to return to the main menu. 4. The display will show V-1.0, the display may also show, V-
When you exit this function, the unit will begin to reload 2.0, V-9.9 etc.
data. 5. Press MODE/ESC to exit.
FEED - With this function you can switch the Pan/Tilt error
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 27 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 28
Vizi LED Spot System Menu Vizi LED Spot System Menu
ADJU - Use this function is used to make sure all motors EDIT - This menu item allows you to write a program into the
are aligned and to adjust any motors that are not. memory (EEPROM) via the control panel or via the external
1. Access the main menu. controller. Please see pages 32-34 for detailed instructions.
2. Tap the UP button until SPEC is displayed, press ENTER. SEPR (IP01-IP07) - With this function you can edit any of
3. Tap the UP button until ADJU is displayed, press ENTER. the internal programs (IP01-IP07).
1. Access the main menu.
4. Tap the UP button until CODE is displayed, press ENTER.
2. Tap the UP button until EDIT is displayed, press ENTER.
5. The display will show CXXX, were as XXX represents the
calibration password. The calibration password is C050. Use 3. Tap the UP button until SEPR is displayed, press ENTER.
the UP or DOWN buttons to enter the proper password. 4. The display will show IPXX. XX represeting 01-07. Tap
6. Once the proper password is entered the display will read the UP of DOWN buttons to find your desired program to edit.
CHXX, were as XX represents the fixture channel number,. Press ENTER to edit the chosen program.
7. Select the desired channel to be calibrated by pressing the 5. Press ENTER to save and press MODE/ESC to exit.
UP or DOWN buttons and then ENTER to confirm.
8. The display will then read xxxx, were xxxx stands for
STEP (S-01 - S-48) - With this function you can program
the number of steps in your individual Program.
the calibrate values.
9. Adjust the desired calibration value between 128 and 127 1. Access the main menu.
by pressing the UP and DOWN. As you scroll up and down 2. Tap the UP button until EDIT is displayed, press ENTER.
through the calibration values you will
notice slight changes in the wheel or motor you are attempting 3. Tap the UP button until STEP is displayed, press ENTER.
to calibrate. 4. The display shows S-01, this stands for the first step of
10. Once you reach your desired calibration press ENTER to your program. You can call up to 48 scenes in Run. For exam-
confirm and lock in your calibration. ple, if S-05 is displayed, it means that Run will run the first
5 scenes you saved in Edit.
11. Once you are completely finished press MODE/ESC to
return to the main menu. 5. Press ENTER to save and press MODE/ESC to exit.
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 33 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 34
Vizi LED Spot Error Codes Vizi LED Spot Error Codes
If after a third attempt all the errors have not been corrected the
fixture will make the following determinations:
1) 3 or more errors - The fixture cannot function properly with
three or more errors therefore the fixture will place itself in a
stand-by mode until subsequent repairs can be made.
2) Less than 3 errors - If the fixture has less than 3 errors, there-
fore most other functions will work properly. The fixture will
attempt to operate normally until the errors can be corrected by
a technician. The errors in question will remain flashing in the
display as a reminder of internal errors.
Figure 5
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 45 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 46
Vizi LED Spot Photometric Chart Vizi LED Spot Fuse Replacement
First unplug the power. The fuse holder is located next to the power
Intensit UX 14770 3113 1348 cord. Using a flat-head screw driver unscrew the fuse holder. Remove
2 the bad fuse and replace with a new one.
1 Due to fog residue, smoke, and dust cleaning the internal and exter-
nal optical lenses and mirror should be carried out periodically to op-
timize light output. Cleaning frequency depends on the environment
Beam opening(m)
in which the fixture operates (I.e. smoke, fog residue, dust, dew). In
0 14 heavy club use we recommend cleaning on a monthly basis. Periodic
cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
1 2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics and mirror with glass cleaner and a soft
cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
2
1 2 3 Distance(m) 30-60 days.
0.25 0.50 0.72 Diameter(m) 5. Always be sure to dry all parts completely before plugging the unit
back in.
Vizi LED Spot Trouble Shooting
Listed below are a few common problems that you may encounter,
with solutions.
No light output from the unit;
1. Be sure you have connected your unit into a standard 120v wall
outlet.
2. Be sure the external fuse has not blown. The fuse is located at
the rear of the unit.
3. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 47 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 48
Vizi LED Spot Warranty Vizi LED Spot Notes
MANUFACTURERS LIMITED WARRANTY
A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
Audio products to be free of manufacturing defects in material and workmanship for a prescribed
period from the date of purchase (see specific warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions
and territories. It is the owners responsibility to establish the date and place of purchase by ac-
ceptable evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before
sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send
the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the
requested repairs or service (including parts replacement) are within the terms of this warranty,
American DJ, Inc. will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in its original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, American DJ,
Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability
of the product; if the product has been repaired or serviced by anyone other than the American DJ,
Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the
product is damaged because not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, American DJ, Inc. will replace defec-
tive parts at its expense with new or refurbished parts, and will absorb all expenses for warranty
service and repair labor by reason of defects in material or workmanship. The sole responsibility
of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replace-
ment thereof, including parts, at the sole discretion of American DJ. All products covered by this
warranty were manufactured after January 1, 1990, and bear identifying marks to that effect.
E. American DJ, Inc. reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products theretofore
manufactured. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by applicable
law, all implied warranties made by American DJ, Inc. in connection with this product, including
warranties of merchantability or fitness, are limited in duration to the warranty period set forth
above. And no warranties, whether expressed or implied, including warranties of merchantability
or fitness, shall apply to this product after said period has expired. The consumers and/or Dealers
sole remedy shall be such repair or replacement as is expressly provided above; and under no
circumstances shall American DJ, Inc. be liable for any loss or damage, direct or consequential,
arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to American DJ and American Audio
Products and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
MANUFACTURERS LIMITED WARRANTY PERIODS:
All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Ampli-
fiers)
All American Audio V-Plus Series Amplifiers = 3-year (1095 day) Limited Warranty
American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty
(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,
and Star Tec Series)
American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty
American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors which
have a 1-year (365 day Limited Warranty)
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 49 American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 50
Vizi LED Spot Specifications
American DJ Supply
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-582-2610
Web: www.americandj.com / E-mail: info@americandj.com
American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
service@americandj.eu / www.americandj.eu
American DJ - www.americandj.com - Vizi LED Spot - Instruction Manual - Page 51
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99