Continuous hot-dip metallic coated steel sheet and strip
Coatings of zinc and zinc alloyed with aluminum and magnesium 1 1. Chemical Composition 3. Coating Mass Whatis ZAM ? Requirements For Chemical Composition Coating Mass Requirements : Type 'ZM' Coatings Steel grade Chemical composition (cast analysis), % max. Minimum coating mass, g/m 2 designation Carbon Manganese Phosphorus Sulfur Coating class designation Total both surfaces One surface 2 AS1397 Manufac- Triple spot Single Spot Single spot G450, G500, G550 0.20 1.20 0.040 0.030 turing ZM60 60 54 24 process G300, G350 (see Note) 0.30 1.60 0.100 0.035 ZM90 90 80 35 G250, G1 0.12 0.50 0.040 0.035 ZM120 120 110 50 G2 0.10 0.45 0.030 0.030 G3 0.08 0.40 0.020 0.025 ZM150 150 135 60 3 ZM180 180 160 70 Qualityy NOTE: For grade G300, nitrogenized steel may be used for sections greater than characte- ZM220 220 200 90 ristics 1.00mm thick. ZM275 275 250 110 ZM350 350 315 140 ZM450 450 405 180 4 2. Mechanical Properties Chromium -free Mechanical Property Requirements For Formability Grades treatment 4. Coating Adhesion Transverse tensile test (see Transverse Thickness Note 1) bent test range for lock Coating Adesion (180 Bend Test) Requirements Steel grade Min. elongation, % seam Diameter of mandrel in terms of thickness of product (t ) designation Degree of on 50mm on 80mm bend (see Note 2) mm Coating class 5 ZM90, Standards G1 180 Steel grade ZM120, ZM220, G2 30 27 180 1.60 ZM350 ZM450 designation ZM150, ZM275 G3 35 32 180 All ZM180, 6 NOTES 1: Applies to test picces equal to or greater than 0.60mm thick. Refer to G250 0 0 0 t Examples of supplier for typical yield and tensile strengths for design purposes. G300 0 t t t pprocessed 2: The ability of grades to lockseam is dependent on recognized proling products G350 0 t t t practices and machine aettings to avoid excessive stretching of the t product. G450 2t 2t 2t 7 G500 2t 2t 2t 2t Acquired q G550 2t 2t 2t 2t certifica- Mechanical Property Requirements For Structural Grades tions G1 0 0 0 t Transverse bend Certifica- Longitudinal tensile test G2 0 0 0 t tes test G3 0 0 0 t Min. yield Min. Diameter Steel Min. elongation, % Angle of strength Tensile of NOTE : 0 indicates that the coated steel is bent at on itselch grade (Note 2) bend (Note 1) strength mandrel designa- in terms 8 tion of Quantity test piece tables MPa MPa L 0 =50mm L 0 =80mm degrees thickness (t ) G250 250 320 25 22 180 0 9 G300 300 340 20 18 180 t Typical yp G350 350 420 15 14 180 2t applica- pp tions G450 450 480 10 9 90 4t (Note 3) G500 500 520 8 7 90 6t 10 (Note 4) Affiliate G550 compani- 550 550 2 2 es' (Note 5) products NOTES 1: The yield strength is the lower yicld stress. If well-dened yielding is not obvious, the 0.2% proof stress should be determined. 2: Applies to test pieces equal to or greater than 0.6mm in thickness. For material up to 0.6mm in thickness, the minimum elongation values in the table are not covered by this standard. 11 L=original gauge lenghth. Precau- 3: Applies to recovery annealed , i.e. not recrystallized after annealing, tions material equal to or greater than 1.50mm thick. 4: Applies to recovery annealed ,i.e. not recrystallized after annealing, material between 1.00mm and 1.50mm thick. 5: Applies to recovery annealed, i.e. not recrystallized after annealing, material up to and including 1.0 0mm thick; the values of yield strength,0.2% proof stress and tensile strength are, for practical purposes, the same.
The coating density of ZAM for calculating thickness of coating layer : 6.0g /cm 3