Académique Documents
Professionnel Documents
Culture Documents
Data Sheet
27631.2C
3133
ULTRA-SENSITIVE BIPOLAR
HALL-EFFECT SWITCHES
These Hall-effect switches are designed for magnetic actuation using
a bipolar magnetic field, i.e., a north-south alternating field. They
combine extreme magnetic sensitivity with excellent stability over
varying temperature and supply voltage. The high sensitivity permits
X
their use with multi-pole ring magnets over relatively large distances.
Each device includes a voltage regulator, quadratic Hall voltage
generator, temperature stability circuit, signal amplifier, Schmitt trigger,
and open-collector output on a single silicon chip. The on-board regula-
tor permits operation with supply voltages of 4.5 to 24 V. The switch
V output can sink up to 25 mA. With suitable output pull up, they can be
CC
used directly with bipolar or MOS logic circuits.
The three package styles available provide a magnetically optimized
1 2 3 package for most applications. Suffix LT is a miniature SOT89/TO-
243AA transistor package for surface-mount applications; suffix UA
features wire leads for through-hole mounting. Prefix UGN devices
are rated for continuous operation over the temperature range of -20C to
+85C, prefix UGS devices over an extended range of -40C to
GROUND
OUTPUT
SUPPLY
+125C, and prefix UGL devices over the range of -40C to +150C.
FEATURES
Dwg. PH-003A
REG.
X 3 OUTPUT
2 GROUND
Dwg. FH-005-2
NOTE: As used here, negative flux densities are defined as less than zero (algebraic convention.)
Typical values are at TA = +25C and VCC = 12 V.
1 gauss (G) is exactly equal to 0.1 millitesla (mT).
* Complete part number includes a prefix denoting operating temperature range (UGL, UGN, or UGS)
and a suffix denoting package type (LT or UA).
TYPICAL CHARACTERISTICS
40 40
OPERATE POINT
OPERATE POINT
20 20
SWITCH POINT IN GAUSS
RELEASE POINT
-20 -20
RELEASE POINT
-40 -40
-50 -25 0 25 50 75 100 125 4.0 8.0 12 16 20 24 28
200 6.0
I OUT = 20 mA
VCC = 12 V
B B OP
175
SATURATION VOLTAGE IN mV
SUPPLY CURRENT IN mA
5.0
150
4.0
125 B B RP
100 3.0
-50 -25 0 25 50 75 100 125 -50 -25 0 25 50 75 100 125
Powering up in the absence of a magnetic field (less than Bipolar switches may switch on removal of field but
BOP and higher than BRP) will allow an indeterminate output require field reversal for reliable operation over temperature
state. The correct state is warranted after the first excursion range; latches will not switch on removal of magnetic field.
beyond BOP or BRP.
www.allegromicro.com
3132 AND 3133
BIPOLAR
HALL-EFFECT SWITCHES
SENSOR LOCATIONS
(0.005 [0.13mm] die placement)
SUFFIX LT
ACTIVE AREA DEPTH
0.0305" 0.089"
0.775 mm 2.26 mm
NOM
0.043"
1.09 mm
A
1 2 3
Dwg. MH-008-2D
Allegro
PACKAGE DESIGNATOR LT
(SOT89/TO-243AA)
0.0189 0.48
0.047 0.0142 1.20 0.36
0.035 0.0221 0.89 0.56
0.0173 1.50 0.44
0.059
BSC BSC
0.118 3.00
BSC Dwg. MA-009-3A in
BSC Dwg. MA-009-3A mm
0.098 2.5
0.079 2.0
B 0.031 B 0.8
A 0.102 A 2.6
0.181 4.6
1 2 3 0.047 1 2 3 1.2
Pads 1, 2, 3, and A Standard SOT89 Layout Pads 1, 2, 3, and A Standard SOT89 Layout
Pads 1, 2, 3, and B Low-Stress Version Pads 1, 2, 3, and B Low-Stress Version
Pads 1, 2, and 3 only Lowest Stress, But Not Self Aligning Pads 1, 2, and 3 only Lowest Stress, But Not Self Aligning
NOTES: 1. Exact body and lead configuration at vendors option within limits shown.
2. Supplied in bulk pack (500 pieces per bag) or add "TR" to part number for tape and reel.
3. Only low-temperature (240C) reflow-soldering techniques are recommended for SOT89 devices.
www.allegromicro.com
3132 AND 3133
BIPOLAR
HALL-EFFECT SWITCHES
PACKAGE DESIGNATOR UA
Dimensions in Inches Dimensions in Millimeters
(controlling dimensions) (for reference only)
0.164 4.17
0.159 4.04
0.062 1.57
45 0.058 45 1.47
0.122 3.10
0.117 2.97
45 45
0.050 1.27
BSC BSC
Dwg. MH-014E in Dwg. MH-014E mm
0.100"
(2.5 mm) Dwg. MH-026
www.datasheetcatalog.com