Vous êtes sur la page 1sur 38

and the siential'

to any person

to persons of

ng in Govern-

blic" or to the

agencies. (Sea
ER.

and the essential

to any person known

ons of undoubted

nment work, but

ess except by author-

r. 28, AR 380-5,
e information and

pts (5);

(2) ASF

Deps (Sig

oc Dists (2).

44 (4).

W Orgn (B)

EC)

138.
ng this equipment

ckaxes, hammers,

rs, incend-

holes.

sistors, capacitors,

fter destroy-
Y.

ble, use a dry nonconductor i rubber gloves, rope.

contact with the victim. If necessary to cut a

ware of the resulting flash.

G.

p lo loosen the victim's clothing. Every moment

vering available. Send for a doctor. Remove false

ectly

that

ur

w you

ll of

bear

over

wing

nt

until there is no hope of the victim's recovery. Do

cess must be kept up for hours.

n the victim's clothing. Wrap the victim warmly; apply

s until he is fully conscious. If the victim must be

spiration. If natural breathing does not continue,

or kneels behind the person giving artificial respiration.

operator releases the pressure.

Keep him quiet. Give hot coffee or tea. or other


ucing a signal of pre-

us tests in electronic equip-

al to various points of the

rcuit upon the injected

cy dial may also be used

ency oscillator oper-

Its output covers the

in 3 bands as follows:

e controls and switch

hed to the front panel,

sformer, tubes, resistors,

crews around the edge

brated against the

ormally used as an ON-

nt panel. However,

rienced personnel. The

y 7 by 9% inches. Two

2.
case.
m the case or carton.

ired tubes in place, it

ert tubes. The line supply

correct voltage and fre-

rner by unscrewing it

0-volt a-c supply. Throw

r should be allowed to

ther circuit components

e the current is on. If,

IV for maintenance

on; at this point the

d carefully set

hould not blink when the

ceed as follows:

adjacent to the

dial set to 60

a non-metallic screw-

er of the neon light.

e load presented

e signal generator.
UT binding posts.

d to ground

esired as marked on

. Scale markings indi-

y by 10 for the 200

nal posts. The total

PUT IMPEDANCE

00, 250, and 10 ohms.

of the OUTPUT CON-

al for any setting of


ned (Wien bridge)

riable ganged capaci-

the range by

e tuning capacitors. There

0 KG.

J7 (VT-116) and a

resistance-coupled

The feedback network is

cillation.

gative feedback to the

network. One section

volt, lamps in series

mplitude of the signal

element, thus controlling

of the theory of this

6SN7 (VT-231)

d push-puH output tube.

ed transformer having

ances of 5,000, 500, 250,

means of the OUTPUT


e from a llOvolt,

-c for the plates of the

or all tubes in the unit

(VT-126-B) tube.

es the required d-c voltage.


e reported immediately

e, see TM 38-250.

y of the components of

ment, fuse, and lamps).

uch replacement, the gen-

n.

eplaced, if damaged,

%-watt, 120-volt neon

are located on the under-

ews around the

ubes are mounted on the

s will insure inserting the

, check the fuse by

. If the fuse is blown, in-

e replacement fuse should

voltage and resist-

shown in figure 4. The

view of the chassis as

r when Signal Corps

perature and relative

ms are typical:

mer windings, etc., caus-

Fungus growth accel-


T AT MINIMUM,

T TO CHASSIS

/V.A.C. VOLTMETER.
inal boards and insula-

ry terminals.

treatment has been

nable degree of protec-

spray, and moisture. The

-resistant varnish applied

the proper operation

from the equipment

and remove case.

el assembly to case and

ve front panel assembly.

citor gang; remove

masking tape as

r, item A, figure 6.

C, figure 6.

stment capacitor,

g, item B, figure 7.

gure 7.

r.

not exceed

nents, decrease

ly one (1) hour for each

nt, Spec No. 71-2202


treated, including inside

er each coat.

e respirator

cloth material

ot reached by spray

ely protected by varnish.

isassembly in reverse,

of treatment.
ails.

Vous aimerez peut-être aussi