Académique Documents
Professionnel Documents
Culture Documents
Date 2014-1-16
Table of Contents
1 Primitive Parameters
2 Settings Calculation
Positive sequence impedance of line:
Load encroachment:
a) Distance protection
Rule:
and
Calculated result:
One stage directional zero-sequence over-current protection is enabled. The primary current takes
240A, the time delay is more than zone 3 of phase-to-ground distance protection, takes 1.8s.
d) SOTF protection
21SOTF.En_PDF is enabled.
50GSOTF.En_3I0 is enabled.
This setting should ensure sufficient sensitivity to ground fault at end of the line, takes primary
current 300A.
e) Automatic reclosure
AR mode: 1-pole AR
f) Overvoltage protection
Phase voltage setting takes 110% of rate secondary phase voltage, time delay takes 3s.
g) Undervoltage protection
Phase voltage setting takes 90% of rate secondary phase voltage, time delay takes 3s.
3 Settings List
Note!
All the settings are the recommended settings, for system parameters are not available, all
the settings have not been check.
For other settings that not listed in this section, please set them according to the actual
condition on site.
System settings
No. Item Range Value
1 Active_Grp 1~10 1
2 Opt_SysFreq 50 or 60 (Hz) 50
3 PrimaryEquip_Name Maximum 12 character
4 U1n 33~65500 (KV) 230
5 U2n 80~220 (V) 110
6 I1n 100~65500 (A) 1600
7 I2n 1 or 5 (A) 1
8 f_High_FreqAlm 50 - 65 (Hz) 53
9 f_Low_FreqAlm 40 - 60 (Hz) 47
Line Parameters
No. Item Range Value
1 X1L (0.000~4Unn)/In (ohm) 6.301
2 R1L (0.000~4Unn)/In (ohm) 1.357
3 X0L (0.000~4Unn)/In (ohm) 18.296
4 R0L (0.000~4Unn)/In (ohm) 3.729
5 X0M (0.000~4Unn)/In (ohm) 0
6 R0M (0.000~4Unn)/In (ohm) 0
7 LineLength 0.00~655.35 (km) 29.4
8 phi1_Reach 30.00~89.00 (Deg) 77.85
9 phi0_Reach 30.00~89.00 (Deg) 78.48
10 Real_K0 -4.000~4.000 0.632
11 Imag_K0 -4.000~4.000 0.011
Fault Detector Settings
No. Item Range Value
1 FD.DPFC.I_Set (0.050~30.000)In (A) 0.1
2 FD.ROC.3I0_Set (0.050~30.000)In (A) 0.1
Direction Settings
No. Item Range Value
1 RCA_OC 45.00~89.00 (Deg) 78
2 RCA_ROC 45.00~89.00 (Deg) 78
3 RCA_NegOC 45.00~89.00 (Deg) 78
4 Z0_Comp (0.000~4Unn)/In (ohm) 0
5 Z2_Comp (0.000~4Unn)/In (ohm) 0
Pilot Scheme Settings
No. Item Range Value
1 85.Opt_PilotMode 0~2 1
2 85.Opt_Ch_PhSeg 0 or 1 0
3 85.En_WI 0 or 1 0
4 85.U_UV_WI 0~Unn (V) 40
5 85.Z.En 0 or 1 1
6 85.En_Unblocking1 0 or 1 0
7 85.t_DPU_Blocking1 0.000~1.000 (s) 0.1
8 85.t_DPU_CR1 0.000~1.000 (s) 0.025
9 85.t_DDO_CR1 0.000~1.000 (s) 0.025
10 85.En_ZX 0 or 1 0
11 85.t_DPU_ZX 0.000~10.000 (s) 0.1
12 85.DEF.En 0 or 1 0
13 85.DEF.En_BlkAR 0 or 1 0
14 85.DEF_En_IndepCh 0 or 1 0
15 85.En_Unblocking2 0 or 1 0
16 85.DEF.3I0_Set (0.050~30.000)In (A) 30
17 85.DEF.t_DPU 0.001~10.000 (s) 10
18 85.t_DPU_CR2 0.000~1.000 (s) 0.025
19 85.t_DDO_CR2 0.000~1.000 (s) 0.025
DPFC Distance Protection Settings
No. Item Range Value
1 21D.Z_DPFC (0.000~4Unn)/In (ohm) 4.511
2 21D.En_DPFC 0 or 1 1
Load Encroachment Settings
No. Item Range Value
1 LoadEnch.phi_Blinder 0~45 (Deg) 18
2 LoadEnch.R_Blinder (0.05~200)/In (ohm) 112.625
3 LoadEnch.En 0 or 1 0
Distance Protection Settings
No. Item Range Value
1 21Q.ZG1.RCA 0 - 45 (Deg) 12
2 21Q.ZP1.RCA 0 - 45 (Deg) 12
44 21Q.ZP4.RCA 0 - 45 (Deg) 12
45 21Q.ZG4.Z_Set (0.000~4Unn)/In (ohm) 1.289
46 21Q.ZG4.R_Set (0.000~4Unn)/In (ohm) 5.156
47 21Q.ZG4.t_Op 0.000~10.000 (s) 1.2
48 21Q.ZG4.En 0 or 1 1
49 21Q.ZP4.Z_Set (0.000~4Unn)/In (ohm) 1.289
50 21Q.ZP4.R_Set (0.000~4Unn)/In (ohm) 5.156
51 21Q.ZP4.t_Op 0.000~10.000 (s) 1.2
52 21Q.ZP4.En 0 or 1 1
53 21Q.Pilot.Z_Set (0.000~4Unn)/In (ohm) 12.89
54 21Q.Pilot.R_Set (0.000~4Unn)/In (ohm) 38.67
55 21Q.Pilot.Z_Rev (0.000~4Unn)/In (ohm) 9.667
56 21Q.Pilot.R_Rev (0.000~4Unn)/In (ohm) 38.67
57 21Q.Z1.En_PSBR 0 or 1 1
58 21Q.Z2.En_PSBR 0 or 1 1
59 21Q.Z3.En_PSBR 0 or 1 1
60 21Q.Pilot.En_PSBR 0 or 1 1
61 21Q.I_PSBR (0.050~30.000)In (A) 0.392
ROC Settings
No. Item Range Value
1 50/51G.K_Hm2 0.000~1.000 0.15
2 50/51G1.3I0_Set (0.050~30.000)In (A) 0.15
3 50/51G1.t_Op 0.000~20.000 (s) 1.8
4 50/51G1.En 0 or 1 1
5 50/51G1.En_BlkAR 0 or 1 1
6 50/51G1.Opt_Dir 0, 1 or 2 0
7 50/51G1.En_Hm2 0 or 1 0
8 50/51G1.En_Abnor_Blk 0 or 1 0
9 50/51G1.En_CTS_Blk 0 or 1 1
10 50/51G1.Opt_Curve 0~13 0
11 50/51G1.TMS 0.010~200.000 1
12 50/51G1.tmin 0.050~20.000 (t) 1
13 50/51G1.Alpha 0.010~5.000 1
14 50/51G1.C 0.000~20.000 1
15 50/51G1.K 0.050~20.000 1
SOTF Settings
No. Item Range Value
1 50GSOTF.3I0_Set (0.050~30.000)In (A) 0.188
2 50GSOTF.En_3I0 0 or 1 1
3 21SOTF.En 0 or 1 1
4 21SOTF.Z2.En_ManCls 0 or 1 1
5 21SOTF.Z3.En_ManCls 0 or 1 1
6 21SOTF.Z4.En_ManCls 0 or 1 1
7 21SOTF.Z2.En_3PAR 0 or 1 1
8 21SOTF.Z3.En_3PAR 0 or 1 1
9 21SOTF.Z4.En_3PAR 0 or 1 1
10 21SOTF.Z2.En_PSBR 0 or 1 0
11 21SOTF.Z3.En_PSBR 0 or 1 0
12 21SOTF.Z4.En_PSBR 0 or 1 0
13 21SOTF.En_PDF 0 or 1 1
14 21SOTF.t_PDF 0.000~10.000 (s) 0.12
15 SOTF.Opt_Mode_ManCls 0, 1 or 2 2
VTF OC Settings
No. Item Range Value
1 51PVT.I_Set (0.050~30.000)In (A) 0.534
2 51PVT.t_Op 0.000~10.000 (s) 1
3 51PVT.En 0 or 1 1
4 51GVT.3I0_Set (0.050~30.000)In (A) 0.3
5 51GVT.t_Op 0.000~10.000 (s) 1
6 51GVT.En 0 or 1 1
OV Settings
No. Item Range Value
1 59P1.U_Set Un~2Unn (V) 70
2 59P1.t_Op 0.000~30.000 (s) 3
3 59P1.En 0 or 1 1
4 59P1.Opt_1P/3P 0 or 1 1
5 59P1.Opt_Up/Upp 0 or 1 0
6 59P1.En_Alm 0 or 1 0
7 59P1.En_52b_TT 0 or 1 0
8 59P1.En_TT 0 or 1 1
9 59P1.Opt_Curve 0~13 0
10 59P1.Opt_TMS 0.010~200.000 1
11 59P1.tmin 0.050~20.000 (s) 0.05
UV Settins
No. Item Range Value
1 27P1.U_Set 0~Unn (V) 57
2 27P1.t_Op 0.000~30.000 (s) 3
3 27P1.En 0 or 1 1
4 27P1.Opt_1P/3P 0 or 1 1
5 27P1.Opt_Up/Upp 0 or 1 0
6 27P1.En_Alm 0 or 1 0
7 27P1.Opt_Curve 0~13 0
8 27P1.Opt_TMS 0.010~200.000 1
9 27P1.tmin 0.050~20.000 (s) 0.05
Broken Conductor Protection
No. Item Range Value
1 46BC.k_Set 0.2~1.00 0.2
2 46BC.t_Op 0.000~600.000 (s) 3
3 46BC.En 0 or 1 1
MiscProt Settings
No. Item Range Value
1 68.En 0 or 1 1
VTS/CTS Settings
No. Item Range Value
1 VTS.t_DPU 0.2 - 100 (s) 1.25
2 VTS.t_DDO 0.2 - 100 (s) 10
3 VTS.En_Out_VT 0 or 1 0
4 VTS.En_Line_VT 0 or 1 1
5 VTS.En 0 or 1 1
Tripping Logic Settings
No. Item Range Value
1 En_MPF_Blk_AR 0 or 1 1
2 En_3PF_Blk_AR 0 or 1 1
3 En_PhSF_Blk_AR 0 or 1 1
4 En_3PTrp 0 or 1 0
5 t_Dwell_Trp 0.000~1000.000 (s) 0.04
Auto-reclosing Settings
No. Item Range Value
1 25.Opt_Source_UL 0-5 0
2 25.Opt_Source_UB 0-5 0
3 25.U_Dd 3.17552 - 50.8083 (V) 30
4 25.U_Lv 31.7552 - 63.5104 (V) 40
5 25.K_Usyn 0.2 - 5 1
6 25.phi_Diff 0 - 89 (Deg) 12
7 25.phi_Comp 0 - 359 (Deg) 0
8 25.f_Diff 0.02 - 1 (Hz) 0.2
9 25.U_Diff 1.27021 - 50.8083 (V) 10
10 25.t_DeadChk 0.01 - 25 (s) 0.05
11 25.t_SynChk 0.01 - 25 (s) 0.05
12 25.En_fDiffChk 0 or 1 1
13 25.En_SynChk 0 or 1 1
14 25.En_DdL_DdB 0 or 1 1
15 25.En_DdL_LvB 0 or 1 1
16 25.En_LvL_DdB 0 or 1 1
17 25.En_NoChk 0 or 1 0
18 79.N_Rcls 1~4 1
19 79.t_Dd_1PS1 0.000~600.000 (s) 0.8
20 79.t_Dd_3PS1 0.000~600.000 (s) 0.8
21 79.t_Dd_3PS2 0.000~600.000 (s) 1
22 79.t_Dd_3PS3 0.000~600.000 (s) 1
23 79.t_Dd_3PS4 0.000~600.000 (s) 1
24 79.t_CBClsd 0.000~600.000 (s) 15
25 79.t_CBReady 0.000~600.000 (s) 0.4
26 79.t_WaitChk 0.000~600.000 (s) 10
27 79.t_Fail 0.000~600.000 (s) 0.3
28 79.t_DDO_AR 0.000~600.000 (s) 0.12
29 79.t_Reclaim 0.000~600.000 (s) 15
30 79.t_PersistTrp 0.000~600.000 (s) 0.2
31 79.t_DDO_BlkAR 0.000~600.000 (s) 15
32 79.t_AddDly 0.000~600.000 (s) 0.5
33 79.t_WaitMaster 0.000~600.000 (s) 3
34 79.t_SecFault 0.000~600.000 (s) 0.3
35 79.En_PDF_Blk 0 or 1 1
36 79.En_AddDly 0 or 1 0
37 79.En_CutPulse 0 or 1 1
38 79.En_FailCheck 0 or 1 0
39 79.En 0 or 1 1
40 79.En_ExtCtrl 0 or 1 0
41 79.En_CBInit 0 or 1 0
42 79.Opt_Priority 0, 1 or 2 0
43 79.SetOpt 0 or 1 0
44 79.En_1PAR 0 or 1 1
45 79.En_3PAR 0 or 1 0
46 79.En_1P/3PAR 0 or 1 0