Académique Documents
Professionnel Documents
Culture Documents
Please read the 'Notice' and the 'Precautions' in the User's Manual before using CX-
Programmer.
The 'CX-Programmer Introduction Guide' describes the basic operation procedure of CX-
Programmer. Refer to the Help or the User's Manual of the PDF file for detailed
descriptions.
* You need Acrobat Reader 4.0 or grater versions in your PC to display the PDF file.
Contents
Available Device Types
Available PC
Chapter 1 Installation - Startup
1. Installation
1-1. Installation of CX-Programmer 1-1
1-2. Installation of OMRON FB Library 1-4
1-3. Installation of CX-Server 1-4
2. Startup of CX-Programmer 1-6
3. New Project Opening and Device Type Settings 1-7
4. Main Window 1-8
4-1. Compatible SYSWIN Key Allocation 1-9
4-2. Section 1-10
4-3. Deletion and Display of Unnecessary Windows 1-12
5. Program Creation 1-13
5-1. Entry of Normally Open Contact 1-14
5-2. Entry of Coil 1-15
5-3. Edit of Symbol Comment 1-17
5-4. Entry of Rung Comment 1-18
5-5. Entry of Normally Closed Contact 1-18
5-6. Entry of Attached Comments 1-19
5-7. Entry of Differential ContactUp 1-20
5-8. Entry of Differential ContactDown 1-20
5-9. Entry of VerticalUp 1-21
5-10. Entry of VerticalDown 1-21
5-11. Entry of Advanced Instructions 1 - Entry of Strings 1-22
5-12. Entry of Advanced Instructions 1 - Useful Functions 1-23
5-13. Entry of Auxiliary Relay - 1.0 Second Clock Pulse Bit 1-24
5-14. Entry of Advanced Instructions 2 - Entry of Differential 1-25
5-15. Entry of OR Rung 1-26
5-16. Entry of Advanced Instructions 3 - Entry by Fun No. 1-27
5-17. Entry of Timer Instructions 1-28
5-18. Entry of Counter Instructions 1-29
5-19. Edit of RungsCopy & Paste 1-30
5-20. Entry of END Instruction 1-30
*1: For WS02-CXPC2-EV5 (one license (limited to micro PLCs)), only these PLC types are available.
*2: CX-Programmer does not support SFC.
*3: To connect with SYSMAC Board, specify the PLC types in parentheses. Only when selecting these PLC types,
you can select SYSMAC Board as a network type.
*4: To connect with SYSMAC CS1 Board, specify PLC types in parentheses. Only when selecting these PLC types,
you can select CS1 Board as a network type.
Available PC
Hardware Requirements
OS Windows95/98/NT4.0 Windows2000/Me Windows XP
Item Service Pack6
Display 800X600 SVGA or grater 800X600 SVGA or grater 800X600 SVGA or grater
CD-ROM drive At least one drive At least one drive At least one drive
Communications At least one RS-232C Port
Port
Recommendation
OS Windows95/98/NT4.0 Windows2000/Me Windows XP
Item Service Pack6
PC PC/AT Compatible PC/AT Compatible PC/AT Compatible
Hard disk space 150M bytes or more free space 150M bytes or more free space 150M bytes or more free space
The capacity of memory required for operation depends on your program size and OS.
If the capacity of your PC is below the memory required for CX-Programmer, the operation of CX-Programmer
may become very slow.
Required memory size:
Calculate the memory required for your program by using the following measuring stick; memory required for a
program of 1k step= 0.5M bytes, and add it to the memory shown in the above Hardware Requirements table.
Ex. Memory size necessary for downloading a program of 250k steps to CX-Simulator and operating it
(OS: Windows2000):
Memory size necessary for operation
= (Memory size shown in the Hardware Requirements table)+ 0.5M bytes x (Program size)
= 128M bytes + 0.5M bytes x 250
= 253M bytes
In this example, the capacity of memory necessary for operation is at least 256M bytes.
Installation
Installation Opening
Opening aa Device
Device type
type Creating
Creating aa
to
to Startup
Startup new
new project
project settings
settings program
program
1. Installation
Caution
zClose all Windows programs before installation.
zIf an old CX-Programmer is installed, be sure to uninstall the old version
before installing Version 5.
1. Insert the installation disk (CD-ROM) of CX-Programmer into the CD-ROM drive
of your PC.
The setup program automatically starts and the [Choose Setup Language]
dialog box is displayed.
If this dialog box is not displayed, double-click the CD-ROM drive on Windows
Explorer.
Click [OK].
Click [Next].
Installation
Installation Opening
Opening aa Device
Device type
type Creating
Creating aa
to
to Startup
Startup new
new project
project settings
settings program
program
After
After checking
checking the the
contents,
contents, click
click
[Yes]
[Yes] ifif you
you accept
accept
all the terms.
all the terms.
Enter
Users name
Company name
License No.
Click [Next].
A confirmation
dialog is
displayed for
your name,
company name
and license
number.
Click [Next].
The installation program is executed and the files of CX-Programmer are automatically
copied under the specified directory.
Installation
Installation Opening
Opening aa Device
Device type
type Creating
Creating aa
to
to Startup
Startup new
new project
project settings
settings program
program
Click [Yes].
Click [Next].
Click [Next].
Click [Finish]. The installation program is executed and the files of the OMRON FB Library are automatically
copied under the specified directory.
Setup Complete Dialog is shown, then click [Finish] button.
Click [Yes].
Click [Next].
The
The [Choose
[Choose
Destination
Destination Location]
Location]
dialog
dialog is
is displayed.
displayed.
Click
Click [Next].
[Next].
Click [Next].
The installation program is executed and the files of CX-Server are automatically
copied under the specified directory.
Click [Finish].
Before
Before starting
starting to
to use
use CX-Programmer,
CX-Programmer, be
be sure
sure to
to read
read Readme
Readme file.
file.
Installation
Installation Opening
Opening aa Device
Device type
type Creating
Creating aa
to
to Startup
Startup new
new project
project settings
settings program
program
2. Startup of CX-Programmer
Windows task bar
[Start]
L
[Programs]
L
Omron
L
[CX-Programmer]
L
[CX-Programmer]
Click
Title Bar
Menus
Toolbars
Project Tree
Symbol Bar
Section
Status Bar
Name Contents/Function
Title Bar Shows the file name of saved data created in CX-Programmer.
The keyboard mapping function allows the function keys to operate like SYSWIN.
Click
Click
When
When SYSWIN
SYSWIN key
key allocation
allocation is
is selected,
selected, aa key
key operation
operation guide
guide will
will be
be displayed
displayed at
at the
the bottom
bottom of
of the
the display.
display.
Example
Giving names
indicating the contents
of processing or
controls is possible.
Select [Rename].
Select [Insert
Section].
As checking the global image (control flow) of a program on the section list, you can go to a specified section.
Double-click a
section that
you want to
check its
ladder.
4-3. Deletion and Display of Unnecessary Windows
Normal screen
To delete Project
Workspace,
Alt 1
Press [Alt]+[1] to
show Project
Workspace again.
To delete Output
Window,
Alt 2
Press [Alt]+[2] to
show Output
Window again.
5. Program Creation
Coding of a simple program is explained here.
Installation
Installation Opening
Opening aa Device
Device type
type Creating
Creating aa
to
to Startup
Startup new
new project
project settings
settings program
program
After checking the cursor position at the upper left of Ladder Window, start programming.
0 of the upper
0 digit of an
address can
be omitted.
ENT
Switch 1
Enter a symbol
ENT comment.
Deletion of instructions
z Move the cursor to the instruction
100
ENT
Coil 0
ENT
Useful
Useful Function:
Function: Automatic
Automatic check
check ofof duplicated
duplicated coils
coils
IfIf aa duplicated
duplicated coil is entered during program creation,
coil is entered during program creation, the
the following
following message
message is
is
displayed and you can notice that the coil is duplicated right
displayed and you can notice that the coil is duplicated right away. away.
Output Window
automatically opens.
Double-click
Double-click
[Reference]
1. Press [Alt]+[Y]. You can switch showing/hiding of Symbol Comment.
Alt Y
Click
3. Select [Tools] | [Options] from the CX-Programmer menu. You can set hiding
of the comment entry dialog.
Click
Ladder Window is
switched to the Symbol
Comment Editing
window.
Copy&Paste
Copy&Paste and
and deletion
deletion of
of one
one or
or more
more comments
comments are
are possible
possible by
by the
the cell.
cell.
Drag the mouse with the Example of copying & pasting comments of two bits
right mouse button Click the right mouse button
pressed to invert the on the bit number of the copy
source bits of copy in destination, and select [Paste].
blue.
Copy&Paste
Copy&Paste of of symbol
symbol
comments
comments isis possible
possible between
between
Excel
Excel and
and CX-Programmer
CX-Programmer too.too.
[Process_at_Startup]
Enter a rung comment.
ENT
ENT
Sensor 1
ENT
Installation
Installation Opening
Opening aa Device
Device type
type Creating
Creating aa
to
to Startup
Startup new
new project
project settings
settings program
program
O 101
ENT Coil 1
ENT R
This function is very useful for keeping change histories at maintenance and notes
of debug bits at startup.
100
Click
Click [Up].
ENT
101
Click
Click [Down].
Ctrl
Or
O 200
ENT Coil 2
ENT R
C 200
ENT ENT
O 300
ENT Coil 3
ENT
Ctrl
Or
V
Installation
Installation Opening
Opening aa Device
Device type
type Creating
Creating aa
to
to Startup
Startup new
new project
project settings
settings program
program
Products ENT
R
Installation
Installation Opening
Opening aa Device
Device type
type Creating
Creating aa
to
to Startup
Startup new
new project
project settings
settings program
program
Click
Click
The reference guide screen of the
.
instruction shows up.
Click
ENT
Installation
Installation Opening
Opening aa Device
Device type
type Creating
Creating aa
to
to Startup
Startup new
new project
project settings
settings program
program
Enter
@MOV #0
D100
Attach
Attach @ @ (at
(at mark)
mark)
before
before instructions. ItIt
instructions. Enter a comment if necessary.
makes
makes thethe instructions
instructions
differential.
differential.
ENT
ENT
R
Installation
Installation Opening
Opening aa Device
Device type
type Creating
Creating aa
to
to Startup
Startup new
new project
project settings
settings program
program
ENT
W 3
ENT ENT
Entry of
ENT comments is
omitted here.
W 4
ENT ENT
Refer
Refer to
to the
the section
section 5-
5-
66 to enter annotations.
to enter annotations.
Installation
Installation Opening
Opening aa Device
Device type
type Creating
Creating aa
to
to Startup
Startup new
new project
project settings
settings program
program
Show
Show the
the [New
[New Instruction]
Instruction] dialog.
dialog.
021
The
The instruction
instruction
corresponding
corresponding to to the
the
entered
entered Fun
Fun No.
No. isis
displayed.
displayed.
Enter
#0 D0 ENT
ENT
Note:
Note:
The
The Fun
Fun No.
No. ofof MOV
MOV
depends
depends on
on PLC
PLC types.
types.
CS-series
CS-series ->-> 021
021
CJ-series
CJ-series ->
-> 021
021
CV-series
CV-series ->-> 030
030
C-series
C-series ->
-> 21
21
Installation
Installation Opening
Opening aa Device
Device type
type Creating
Creating aa
to
to Startup
Startup new
new project
project settings
settings program
program
Refer
Refer to
to the
the former
former
pages
pages toto enter
enter
rungs
rungs and
and
comments.
comments.
/ T0 ENT
*T0: Indicates TIM0.
Enter a comment.
Timer 1 ENT
TIM 0 #30
ENT
R
Installation
Installation Opening
Opening aa Device
Device type
type Creating
Creating aa
to
to Startup
Startup new
new project
project settings
settings program
program
Refer
Refer to
to the
the former
former
pages
pages to execute
to execute
coding.
coding.
CNT 0 #5
ENT
Move the cursor by
using arrow keys or a
mouse.
Enter a bit for reset.
C C0 ENT
Entry of a Counter bit
ENT
O 402 ENT
ENT
R
Installation
Installation Opening
Opening aa Device
Device type
type Creating
Creating aa
to
to Startup
Startup new
new project
project settings
settings program
program
Move
Move the
the cursor
cursor to
to 5-19. Edit of Rungs Copy & Paste
this
this position.
position. The
The
rung
rung is
is inverted
inverted as
as Refer to the former sections to enter a rung.
shown
shown right.
right.
Ctrl C
(Copy a rung) You can copy instructions selected by dragging a mouse.
You can also cut selected rungs (instructions) by [Ctrl]+[X].
Press the key
Press the key to
to
move
move the cursor to
the cursor to
this
this position.
position.
Ctrl V
At
At the
the creation
creation of
of aa new
new project,
project, aa
section
section of the END instruction only
of the END instruction only is
is
automatically generated.
automatically generated.
You
You dodo not
not need
need to
to enter
enter an
an END
END
instruction.
instruction.
Note:
The END section is not generated when you load a program
created with CX-Programmer V2 or the former versions.
Online
Online Force
Force On
On Program
Program Online
Online
Monitoring
Monitoring
to
to Transfer
Transfer Force
Force Off
Off Check
Check Edit
Edit
Click
Errors
Errors and
and addresses
addresses
are
are displayed on
displayed on
Output
Output Window.
Window.
Double-click
Double-click aa
displayed
displayed error,
error, and
and
the
the cursor in
cursor in Ladder
Ladder
Diagram
Diagram will
will go
go to
to the
the
corresponding error
corresponding error
location
location and
and the
the error
error
rung
rung will be shown in
will be shown in
red.
red.
2. Going Online
Normal
Normal online.
online. Enables
Enables you
you to
to go
go online
online with
with aa PLC
PLC of
of the
the device
device type
type and
and method
method specified
specified when
when opening
opening aa project.
project.
Auto
Auto online.
online. Automatically
Automaticallyrecognizes
recognizes the
the connected
connected PLC
PLC and
and enables
enables you
you to
to go
go online
online with
with aa PLC
PLC with
with one
one button.
button.
->
-> Uploads
Uploads all
all data
data such
such as
as programs
programs from
from the
the PLC.
PLC.
Online
Online with
with Simulator.
Simulator. Enables
Enables you
you to
to go
go online
online with
with CX-Simulator
CX-Simulator with
with one
one button
button (You
(You need
need to
to install
install CX-Simulator.)
CX-Simulator.)
This
This time,
time, online/debug
online/debug
functions
functions when
when working
working
online
online with
with CX-Simulator
CX-Simulator
are
are explained
explained in in this
this
guide (Install CX-
guide (Install CX-
Simulator
Simulator separately).
separately).
Click
Click [OK].
Program transfer starts.
Click [OK].
The
The background
background color
color
of
of Ladder
Ladder Window
Window
The
The CX-Simulator
CX-Simulator changes
changes toto gray.
gray.
Console
Console box
box is
is
shown.
shown.
The
The operating
operating mode
mode
of
of the
the active
active PLC
PLC is
is
shown.
shown.
Scan
Scan time
time is
is displayed
displayed
(except
(except for
for Program
Program Mode).
Mode).
Online
Online Force
Force On
On Program
Program Online
Online
Monitoring
Monitoring
to
to Transfer
Transfer Force
Force Off
Off Check
Check Edit
Edit
3. Monitoring
Change
Change the
the PLC
PLC
(simulator)
(simulator) to
to The on/off statuses of contacts and coils are monitored.
Monitor
Monitor Mode.
Mode.
Click
The
The rungs
rungs being
being
monitored
monitored areare shown
shown
in
in aa specified
specified color.
color.
The
The present
present value
value of
of
I/O
I/O memory
memory isis shown.
shown.
Online
Online Force
Force On
On Program
Program Online
Online
Monitoring
Monitoring
to
to Transfer
Transfer Force
Force Off
Off Check
Check Edit
Edit
You can split Ladder Window and monitor more than one location in a program at once.
Move
Move thethe mouse
mouse
pointer
pointer toto the
the arrow
arrow
position
position shown in
shown in the
the
right figure and drag
right figure and drag
the
the cursor
cursor down
down with
with
the
the left mouse button
left mouse button
pressed.
pressed.
The
The screen
screen is is divided
divided
into
into two
two panes
panes up up
and
and down,
down, andand you
you
can
can display
display any
any
address
address in in two
two panes
panes
respectively
respectively by by using
using
the
the scroll
scroll bars.
bars.
Shown in decimal
Shown in hex
Online
Online Force
Force On
On Program
Program Online
Online
Monitoring
Monitoring
to
to Transfer
Transfer Force
Force Off
Off Check
Check Edit
Edit
Display Watch
Window.
Alt 3
ENT
Press the ENT key
continuously for auto
increment of addresses.
You
You can
can also
also enter
enter aa given
given
address
address in
in this
this status.
status.
ENT
ENT
ENT The addresses registered in Watch Window are still stored
when CX-Programmer is opened next time.
Entry
Entry of
of BOOL
BOOL type
type Example: Entry of 4CH 00Bit
(contact)
(contact) Enter
Enter .
. (period)
(period) between
between CH
CH and
and Bit.
Bit.
Or
Or enter
enter 400
400 without
without aa period
period in
in the
the Name
Name or or
address
address boxbox and
and then
then specify
specify BOOL
BOOL in in the
the Data
Data
Type/Format
Type/Format box box (Reverse
(Reverse the
the box
box and
and then
then press
press BB
key
key form
form the
the keyboard.)
keyboard.)
Online
Online Force
Force On
On Program
Program Online
Online
Monitoring
Monitoring
to
to Transfer
Transfer Force
Force Off
Off Check
Check Edit
Edit
An entry dialog
opens.
Click
Enter a new
value that you
want to change to.
4-word
4-word data
data isis
displayed
displayed in
in the
the
binary
binary system.
system.
Watch Window has a function that classifies and displays data in sheets like MS-
EXCEL and names each sheet given names.
This function is useful for debug or startup if you gather and manage the bits and words
you want to check as one block in one sheet.
Click
Click the
the right
right button
button
of
of aa mouse
mouse on on Sheet1,
Sheet1,
and
and then
then select
select
[Watch
[Watch Sheet]
Sheet] -> ->
[Rename].
[Rename].
Enter
Enter aa name.
name.
To Click
Click [OK].
[OK].
To add
add aa sheet,
sheet,
select
select [Watch
[Watch sheet]
sheet]
->
-> [Insert].
[Insert].
The
The names
names setset by
by this
this operation
operation are
are all
all saved
saved when
when the
the project
project is
is saved
saved (extension:
(extension: .opt).
.opt).
Therefore,
Therefore, they
they are
are loaded
loaded as
as well
well as
as data
data such
such as
as ladder
ladder programs
programs whenwhen the
the project
project is
is
loaded
loaded next
next time.
time.
Online
Online Force
Force On
On Program
Program Online
Online
Monitoring
Monitoring
to
to Transfer
Transfer Force
Force Off
Off Check
Check Edit
Edit
Move
Move the
the mouse
mouse Drag & Drop from Ladder Diagram enables you to add an address to be monitored.
cursor
cursor to
to this
this
position.
position.
Drag
Drag and
and drop
drop on
on Watch
Watch
Window.
Window.
Data
Data such
such as
as rungs,
rungs, bits
bits per
per block,
block, oror operands
operands ofof advanced
advanced instructions
instructions is
is
pasted on Watch Window.
pasted on Watch Window.
Moreover,
Moreover, the
the on/off
on/off statuses
statuses ofof the
the bits
bits and
and the
the present
present values
values of
of words
words
are displayed.
are displayed.
Online
Online Force
Force On
On Program
Program Online
Online
Monitoring
Monitoring
to
to Transfer
Transfer Force
Force Off
Off Check
Check Edit
Edit
This function makes a rung longer than the right bus bar as shown in the below figure
wrap when displayed.
Once set, this function is always active until released by taking the reverse
procedure of the above one.
Online
Online Force
Force On
On Program
Program Online
Online
Monitoring
Monitoring
to
to Transfer
Transfer Force
Force Off
Off Check
Check Edit
Edit
The function detects differential up/down of a specified bit and indicates that
differential conditions are satisfied by sound or display.
The function eliminates the use of a trap rung for checking operation and
improves the efficiency of programming and debug operations.
Click
The
The count
count number
number is is displayed
displayed on on the
the
dialog every time the differential
dialog every time the differential
condition
condition (differential
(differential up
up in
in this
this
example)
example) is satisfied and the
is satisfied and the color
color of
of
the box changes each
the box changes each time. time.
Online
Online Force
Force On
On Program
Program Online
Online
Monitoring
Monitoring
to
to Transfer
Transfer Force
Force Off
Off Check
Check Edit
Edit
Click
Click the
the right
right mouse
mouse
button.
button. ->
->
[Force]
[Force] ->
-> [On]
[On] mark indicates that the bit is
now being forced on/off.
Force
Force Off/Cancel
Off/Cancel of
of Once bits/coils are forced on/off, the forced statuses are held until cancelled or the
bits/coils
bits/coils are
are enabled
enabled reverse procedures of on/off are taken.
in
in the
the same
same way.
way. The statuses do not change by an external input or the operational result of the
program.
Moreover, force operations are not enabled when the PLC is in the Run mode.
Shortcut
Shortcut Key
Key
Ctrl+J:
Ctrl+J: Force
Force On
On
Ctrl+K:
Ctrl+K: Force
Force Off
Off 13. Displaying List of Forced-on/off Bits
Double-click
[Memory].
Click the
[Address] tab.
Double-click
[Forced Status].
Online
Online Force
Force On
On Program
Program Online
Online
Monitoring
Monitoring
to
to Transfer
Transfer Force
Force Off
Off Check
Check Edit
Edit
ENT
Or double-click.
The present value of a timer is changed while CPU is running (in the Monitor mode only).
ENT
Or double-click.
Display Address
Reference Tool.
Alt 4
Reference 1
Enter
Enter aa bit
bit number
number that that you
you
want
want toto find
find in
in the
the [Address]
[Address] 2 Click
field.
field.
3
You
You can
can also
also move
move thethe The
The found
found
cursor
cursor to
to aa bit
bit that
that you
you
want
bits
bits are
are listed.
listed.
want to
to find.
find.
(1)The reason why the coil 3.00 is not turned on is that its contact 2.00 is not turned on.
Therefore, the function retraces rungs to find the coil 2.00.
(2)Move the cursor to the following position (contact 2.00) and press the [Space] key.
Space
(3)The reason why the coil 2.00 is not turned on is that the contact 1.00 or 1.01 is not
turned on. Suppose the cause is the contact 1.00 and find the coil of 1.00. Move the
cursor to the contact 1.00 and press the [Space] key as well as the above operation (2).
Space
(4)If this rung is not a cause press [Shift]+[Space], and you will able to go back to the
rung before you started to find this rung.
Shift Space
Online
Online Force
Force On
On Program
Program Online
Online
Monitoring
Monitoring
to
to Transfer
Transfer Force
Force Off
Off Check
Check Edit
Edit
(5)Then retrace rungs to find a cause from the contact 1.01. As well as the operations
so far, move the cursor to the contact 1.01 and press the [Space] key.
Space
(6)The focus moves to the coil 1.01. As it turned out, the cause was the contact 0.01
that was not turned on.
Press the [Space] key to jump from a coil to a contact having the same address as the
coil or from a contact to a coil in reverse.
Press the [N] key for another jump from a contact or coil at the cursor position to a next
one having the same address.
To move back to the position of the last jump, press the [B] key.
Click
Click .
The [Find] dialog
Select [All (strings)] from the
shows up.
pull-down menu.
Click [OK].
The
The contacts/coils
contacts/coils of
of which
which
annotations
annotations include
include thethe
keyword
keyword entered
entered in
in the
the
Find
Find dialog
dialog are
are displayed
displayed
on
on Output
Output Window.
Window.
Double-click
Double-click anan item,
item, and
and then
then
the cursor moves to
the cursor moves to the the
applicable
applicable bit
bit in
in Ladder
Ladder
Window.
Window.
Online
Online Force
Force On
On Program
Program Online
Online
Monitoring
Monitoring
to
to Transfer
Transfer Force
Force Off
Off Check
Check Edit
Edit
This is a function that displays a list of rung comments on the screen and moves the
cursor to the position where a selected rung comment is used in the ladder.
Rung comments improve the efficiency of debug or maintenance of rungs divided into
blocks per function.
Or
Alt Shift R
Enter an address
(bit number) to find.
(period between a
channel and a bit is
unnecessary.)
Click [OK].
Output
Output Window
Window is is
displayed
displayed and
and the
the
results
results are
are listed.
listed.
Double-click
Double-click an an item
item
in
in the
the list,
list, and
and thethe
cursor
cursor willwill go
go to to the
the
applicable
applicable bit. bit.
Online
Online Force
Force On
On Program
Program Online
Online
Monitoring
Monitoring
to
to Transfer
Transfer Force
Force Off
Off Check
Check Edit
Edit
Double-click
Double-click
(3) Enter a bit number (4.11 in this example) you want to edit to.
(4) Select [Program] -> [Online Edit] -> [Send Changes] from the menu.
End
Useful Functions
Check
Check the
the [Show
[Show
output instructions
output instructions
horizontally
horizontally (H)]
(H)] box.
box.