Académique Documents
Professionnel Documents
Culture Documents
UBPG PM FS5
FS3 UBPG FS3 BPN2
PM PM
UBPG/BPK NULL/BPK
SA CC2/CC16B BPK SA CC16B BPK
Ethernet Cable are enough for both transmission and BBU transmission topology
synchronization BPN2
NULL/BPK
If BPN2 is not adopted for the case of existing 2G and 3G BPK
U U U U U U Interface
Description
2 2 2 2 2 2 Name
6 pairs of optical/electrical
1 1 1 1 1 1 TX0 RX0 to
interfaces, connected to
0 0 0 0 0 0 TX5 RX5
RRU/RSU
0 0 0 0 0 0
G G
G G G cabinet RC8910A cabinet
1 1 1 G G G U U
9 9 G G
8 8 8
0 0
0 0 0
UMTS RF module in the sub 9 9
1 1 1
8 8 8
2
1
2
1
UMTS RF module in beside
0 0 0 0
0 0 0 0 0 0 0 0
cabinet 0 0
0 0 0 0 0 RC8910A cabinet
BBU RRU scenario adopts the RRU scenario adopts the
same principle same principle
UBPG PM FS5
FS3 UBPG FS3 FS3 BPN2
PM UBPG/NULL PM NULL/BPK PM NULL/BPK
SA CC2/CC16B SA CC2/CC16B BPK SA CC16B BPK
G G U U G G G U U
G G
1 1 Two BBU merge into one 2 2
G G
1 1 1 2 2
9 9 9 9
8 8 1 1 8 8 8 1 1
0 0 0 0
0 0
0 0 and keep existing cabinet 0 0
0 0
0 0 0 0 0
0 0 0 0 0 0 0 0 0
RRU scenario adopts the
BBU same principle BBU BBU
UBPG PM FS5
FS3 UBPG FS3 FS3 BPN2
PM UBPG/NULL PM NULL/BPK PM NULL/BPK
SA CC2/CC16B SA CC2/CC16B BPK SA CC16B BPK
Specification
L: 2*1.4/3/5/10/15/20MHz Cells
422 mm
422 mm
Capacity GL: 6 TRXs+1*20M Cell@1800M
UL: 4 Carriers (non-MIMO) + 1*20M Cell
2*60W@AP700/850/1800/2100/2600MHz/AWS
Max TOC
2*40W@2.6GHz
TxRx 2T4R
Typical Power GL: 260W (G S8 + L S1, 1800MHz)
Consumption L: 220W(1800MHz) 210W(2100MHz) 215W(2600MHz)
G:-113.5dBm@single antenna
Small size, easy installation Receiver Sensitivity L: -109.2dBm@dual antennas
-112dBm@four antennas
Supporting 2T4R, MIMO capable
Power Supply 48V DC, 220V/110V AC
Uplink sensitivity enhanced by 3dB
Interface 2*6G/10Gbps CPRI interfaces
Covering the full band at 2600MHz
Frequency band AP700/850/1800/2100/2600 MHz/AWS
DCS&GSM Scenario 9
DCS Scenario 10
GSM Scenario 11
According to the frequency, this table can be used to search for the corresponding scenario.
ZTE Corporation. All rights reserved
15
Scenario1
Scenario1 means the existing 1800M Power doesnt
exceed 80W. 1T2R needs to be changed to 2T2R when
the network upgrade to LTE. It can be achieved by
changing one RSU60 GU188 to RSU82 S1800 or
changing RSU82 S1800 from 1T2R to 2T2R.
1800M needs separate because of PIM2 interference.
Equipment Configuration Principle
RSU82 S1800 Need one(Add or Reuse)
Dual Band TMA No need
1800M TMA Add one
Feeder Add one pair
Jumper Add one pair
NSBT and AISG Both add one
Antenna Unchanged
Combiner Unchanged
Cabinet One needed if not enough room for 6 RSU in one site
DCS&GSM Scenario18(HW solution the same as Scenario 9(The high power means 60W))
DCS Scenario19(HW solution the same as Scenario 10(The high power means 60W))
Jumper
Combiner
Jumper AISG cable Combiner
AISG cable Jumper
Fiber Fiber