Académique Documents
Professionnel Documents
Culture Documents
FDL is equipped with electrical actuator, junction box and fusible link
Halton FDL fire dampers are type-approved class Available as ATEX approved. Shock-tested.
A0(A60) fire dampers for use in offshore, marine and Fixed frame and blades of painted, galvanized or
navy ventilation systems. The FDL can be installed in stainless steel. Maintenance-free stainless steel
rectangular or circular ducts. The FDL dampers are bearings and shafts.
used to prevent the spread of fire within the ventilation Blades without sealing
ductwork. All fire dampers have a fusible link and spring Nominal fuse release temperature 50 C, 74 C
return actuator. When the blades are in the open position, or 100 C. Other temperatures available.
the device does not cause significant pressure loss or Can be installed in any position
flow disturbance. Fire dampers are set from outside and Automatic electrical, pneumatic or spring operation
can be installed in any position. An open-closed indicator system available
is visible on the outside of the damper. Fire dampers Maximum duct pressure for damper construction
with non-standard dimensions can also be supplied on 5000 Pa and maximum air velocity 15 m/s. In case of
request. high duct pressure, contact Halton Marine for finding
Type-approved by most recognized classification the most suitable solution.
societies: class A0 without insulation, A15-A60 when
suitably insulated
Modular construction sizes up to 2660x2460 mm. The above table contains only some examples of actuators and their
effect on dimensions.
Standard frame material thickness 3-5 mm. Material
thickness according to SOLAS available on request. Frame thickness according to SOLAS
DIMENSIONS S L
9
n*150
S, ACCORDING TO SOLAS
ACTUATOR
150
H+56
H+2
A
D
150
n*150
MIN. 50
150 150
9
S, ACCORDING TO SOLAS
TO SOLAS
217, S=5
214, S=4
212, S=3
160
>50
Size limitation:
nx 150
FDB2 Max.1604
FDL Max.1202
FDB2:
nx 150
Nominal Width 2060 x Nominal Height 3260
or
>50
Nominal Width 2460 x Nominal Height 2860
C
2
FDL
Nominal Width 2660 x Nominal Height 2460
DETAIL C
SCALE 1 : 5
Flat bar steel both side
of the damper
10 (FDB2)
9 (FDL)
2
10 (FDB2)
9 (FDL)
Max 10
Flat bars to be sealed with pyrocryl sealant
Min 3
S
FDL PRODUCT OPTIONS OPERATION PRINCIPLE
Halton FDL is available with following actuators: In the event of a temperature rise in ductwork:
FDL-EL: Electrical spring return motor; standard FDL-EL: fusible link releases and cuts off operating
actuators being 24 V or 230 V or 120 V. The motor voltage to the spring return motor, allowing the
contains built-in open-closed limit switches. Separate spring to close the damper blades. The fire damper
junction box included in the EL-model. A wide range opens automatically when the fuse has been
of eex-proof actuators available, including a one changed and the operating voltage to the motor is
second closing time function as an option. re-established.
FDL-PNL: Pneumatic linear actuator, FDL-PNL and FDL-PNR: fusible link releases and cuts
material stainless steel off operating pressure to the spring return actuator,
FDL-PNR: Pneumatic rotating actuator allowing springs to close the damper blades. The
FDL-SP: Manual spring-actuated damper with fusible fire damper opens automatically when the fuse
link has been changed and the pneumatic air supply is
DOT: manual override function available for PNL, PNR re-established.
and EL models. A wide range of accessories available. FDL-SP: fusible link releases allowing the spring to
close the damper blades. When the fuse has been
changed, the fire damper must be reset into open
position manually.
M20 M16
M20 M16
1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 6 7 8 9 10 11
END CLAMP
END CLAMP
END CLAMP
1 2 3 4 5 6 7 8 9 10 11 END CLAMP 1 2 3 4 5 6 7 8 9 10 11
BN BU 2(BN) 1(BU) S1 S2 S3 S4 S5 S6
13 14 1 2 S1 S2 S3 S4 S5 S6
M16
M16 M16 M16 M16 M16
2 x 0,75 mm 6 x 0,75 mm
2 x 0,75 mm 6 x 0,75 mm
2 x 0,75 mm
BELIMO
BELIMO BF24-T
BF24 1 2 S1 S2 S3 S4 S5 S6 BF230-T
SIHF
1 2 S1 S2 S3 S4 S5 S6 BF120 INTERNAL
BF230
THERMAL SWITCH
BLF24
FUSIBLE LINK
14 72C IP54
M 5 80
BLF120
BLF230 BAE72-S
5 80
13 WHEN DAMPER IS NOT ENERGIZED IP54 M WHEN DAMPER IS NOT ENERGIZED
CONTACTS S1-S2, S4-S5 ARE CLOSED CONTACTS S1-S2, S4-S5 ARE CLOSED
FDL-EL WIRING DIAGRAM with ExMax or RedMax FDL-EL WIRING DIAGRAM with Elodrive actuator
actuator
POWER SUPPLY
24V AC/DC
120/230 V AC
POWER SUPPLY DAMPER DAMPER L/+ N/-
24-230V AC/DC CLOSED OPEN
L/+ N/- PE 1 2 3 4
M20
M20 M20
M16
PE
L/+ N/- 1 2 3 4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 L/+ N/-
1 2 3 4 5 6 7 8 9 10 11
END CLAMP
END CLAMP
PE -EARTHING RAIL
END CLAMP
END CLAMP
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
BK GY BN 2 3 5 1 4 1 2 3 4 5 6
PE 1 2 3 4 5 6 7 8 9 10 11
13 14 2 3 1
M16
M16 M16
3 x 0,75 mm 6 x 0,5 mm 6 x 0,5 mm
ExMax-5.10-SF
RedMax-5.10-SF
PE 2 3 5 1 4 1 2 3 4 5 6 ExMax-15-SF 3 x 0,75 mm
FUSIBLE LINK
RedMax-15-SF
GY
BN
BK
HEATER
5 85 IP66
2 x 0,75 mm
CSQP-05A2E
CSQP-10A1E
CSQP-10A2E
FUSIBLE LINK
14 N L1 CSQP-15A1E
- + CSQP-15A2E
T ~
IP66
13
4
7 8. PLASTIC TUBE. OPTION:
M20 M16 STAINLESS STEEL
L/+ N/- 1 2 3 4 JUNCTION BOX 2
1 2 3 4 5 6 7 8 9 10 11 QUICK EXHAUST 9. OPTION: OPEN / CLOSED
VALVES SWITCHES
END CLAMP
END CLAMP
3 6
8 10. OPTION: MANUAL VALVE
(-)
(+)
13 2 4 3 54 56 6 77 88 99 101011 11 PIPELINES:POLYAMIDE
1 2 11. PRESSURE REGULATOR
BN BU BN BU S1 S2 S3 S4 S5 S6 6 4
13 14 1(3) 2(4)
FUSIBLE LINK 12. SPEED CONTROLLER
S2
S3
S4
S5
S6
S1
1
6 10
M16 M16 M16
M16 M16 M16 OPTION:
MANUAL VALVE
3 PORT/2 WAY 6
FUSIBLE LINK 3 8
2 x 0,75 mm 6 x 0,75 mm OPTION: 50/74/100C
6 5
OPTION:
S2
S3
S4
S5
S6
S1
2
2 x 0,75 mm
3 PORT/2 WAY
M
BELIMO 6
SIEMENS
S4BF24
S5 / BF120
S6 / BF230
SIHF
1(3) 2(4)
3 87 S1 S2 S3
BLF24 / BLF230
GGA.126.1E/HA
GGA.226.1E/HA
3 8
6
FUSIBLE LINK
14
M IP 54
GGA.326.1E/HA
GNA.126.1E/HA
5 80 GNA.326.1E/HA PRESSURE REGULATOR
13 WHEN DAMPER IS NOT ENERGIZED IP54 11
CONTACTS S1-S2, S4-S5 ARE CLOSED 6
PNEU. INLET (5 - 8 BAR)
FOR A PLASTIC TUBE
6 MM
AC24V
FDL-EL WIRING DIAGRAM with Siemens-HA1
DC24...48V
AC120V DAMPER DAMPER 24....230 VAC/DC CLOSED AND OPENED
actuator INFORMATION OUT
AC230VPOWER SUPPLY
CLOSED OPEN (+)(-)
(-) (+) 24, 230 VAC DAMPER DAMPER PE ~ ~
24...48 VDC CLOSED OPEN
L/+ N/- 1 2 3 4 M20 M20
1
JUNCTION BOX
M20 M16
M20 M16 JUNCTION BOX
PE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
(-)
(+)
1 2 3 4 5 6 7 8 9 10 11
2(4)
1(3)
S2
S3
S4
S5
S6
S1
PE BK BE BN 2 3 5 1 4 S1 S2 S3 S4 S5 S6
L/+ N/- 1 2 3 4 THERMAL FUSE
1 2 3 4 5 6 7 8 9 10 SM-072-A0-2A
11 (72C)
END CLAMP
END CLAMP
FUSIBLE LINK
BLUE
OPTION: 50/74/100C
M16
2(4)
1(3)
S2
S3
S4
S5
S6
S1
M16 M16
M
SIEMENS
GGA.126.1E/HA
3 87 GGA226.1E/HA
2 x 0,75 mm 6 x 0,75 mm GGA326.1E/HA FUSIBLE LINK
GNA126.1E/HA OPTION: 50/74/100C
GNA326.1E/HA (BARTEC)
IP 54
SIEMENS
GGA.126.1E/HA1
1(3) 2(4) S1 S2 S3 S4 S5 S6 GGA.326.1E/HA1
TEMPERATURE
MONITORING UNIT PE 2 3 5 1 4 S1 S2 S3 S4 S5 S6 Schischek
72C
5 80
M WHEN DAMPER IS NOT ENERGIZED 5 85 IP 66
CONTACTS S1-S2, S4-S5 ARE CLOSED
SIEMENS-HA1