Académique Documents
Professionnel Documents
Culture Documents
TECHNICAL
TECHNICAL / PRODUCT
/ PRODUCT GUIDE
GUIDE
INTRODUCTION
“Hepworth has a declared Company objective to design and manufacture products to the highest standards of quality and
technical excellence, to satisfy all appropriate standards, customer requirements and company specifications.
To achieve this objective, the policy of the Board of Directors is to maintain and continually improve through regular review,
an effective and efficiently quality management system. The quality system provides a framework for control based on the
ISO 9000 series of Quality System Standards.
Where appropriate, this policy is endorsed through third party certification such as BSI Kitemark Licence Schemes. In certain
circumstances, where recognized national/international technical product standards do not exist or are considered insuffi-
cient, third party approval/quality system certification is obtained through British Board of Agreement or other recognized
approval authorities”.
Due to formation of European Union the British Standards Institute (BSI) and their European equivalent formed an internation-
ally accredited committee to oversee the development of a library of Standards which combined the British Standards and the
European Standards.
This is progressively being achieved and as it happens the new standards are being released for use and the old standards are
then withdrawn and are no longer recognized.
The standard for the Hepworth P.M.E. uPVC Piping Systems for non pressure above ground soil and vent systems has now
been changed from:
BS 4514 - to - BS EN 1329
CONTENTS
PUSH-FIT WASTE 19 - 20
TRAPS 24 - 28
PUSH-FIT OVERFLOW 29
2
RANGE LIST
TRAPS
Material Polypropylene (PP)
Colour White
Depth of Seals ¾” 19mm; 1 ½ ” 38mm; 3” 76mm
Types Bottle
Tubular
Anti-syphon
PUSH-FIT WASTE
Material Polypropylene (PP)
Colours Grey in all sizes
Black, Brown, Copper in 11/4” 32mm
and 1 1/2” 40mm only
3
SOLWELD SOLVENT WELD
WASTE SYSTEM Material Acrylonitrile Butadiene Styrene (ABS)
Colour White, Grey, Black and Brown
Sizes Nom OD 1 1/4” 32mm; 1 1/2” 40mm;
2” 50mm
Actual Min OD 36.15; 42.75; 55.75
Standards BS5255 (where applicable)
PUSH-FIT OVERFLOW SYSTEM
Material Polypropylene (PP)
Colour Grey, White. Selected items available
in black and brown
4
SOIL AND VENTILATION SYSTEMS
Description Dimension Effect of Chemicals
Hepworth Soil and Ventilation Systems Nominal size 3” 4” 6” uPVC is resistant to most acids, alkalis
are manufactured in 82mm (3”), 110mm Actual min OD 82.40 110.0 160.0 and oils but liable to attack by concen-
(4”) and 160mm (6”) sizes in grey uPVC. Lengths – metres 2.0 2.0 2.0 trated sulphuric, nitric and chromic acids
Selected components of 82mm (3”) 2.5 2.5 2.5 and organic solvents. For specialized
system are also available in black. 3.0 3.0 3.0 applications, consult the Technical
Selected components of 110mm (4”) 4.0 4.0 4.0 Services Department for advice.
system are also available in black and
brown. Weight
Reaction with other Materials
The push-fit joints allow for the expan- 82mm pipe = 1.3 Kg/m: (mean)
uPVC has not been found to react
sion of pipes and incorporated a unique 110mm pipe = 1.59 Kg/m: (mean)
adversely with any traditional building
and patented purpose designed sealing materials.
method. A sealing ring is contained in a Colour
moulded housing designed to prevent Grey to BS4514
displacement either during installation or
Maintenance
(WC connections are white)
as a result of the action of expansion and Designers should provide adequate
contraction. The 110mm (4”) system is also in black access for periodic cleaning. Access
or brown. pipes and bosses are available within
These lightweight soil systems are the range.
simple to install and are maintenance Thermal Movement
free. Prefabricated Items
Coefficient of linear expansion 0.5 x
Application 10 / C temperature rise, i.e. 1mm per For particular installations that require
-4 o
5
SOIL AND VENTILATION SYSTEMS
Plain Ended Pipe Cat. No. Dimensions Sizes
L 82 110 160
(3) (4) (6)
SP25PE 2.5m (8.2ft)
SP3PE 3.0m (9.8ft)
SP3PE/3 3.0m (9.8ft)
SP4PE 4.0m (13.1ft)
SP4PE/3 4.0m (13.1ft)
SP4PE/6 4.0m (13.1ft)
Single Socket Pipe Cat. No. Dimensions Sizes
L 82 110 160
(3) (4) (6)
SP2SS/3 2.0m (6.6ft)
SP2SS 2.0m (6.6ft)
SP2SS/6 2.0m (6.6ft)
SP25SS 2.5m (8.2ft)
SP3SS 3.0m (9.8ft)
SP3SS/6 3.0m (9.8ft)
SP3SS/3 3.0m (9.8ft)
SP4SS 4.0m (13.1ft)
SP4SS/6 4.0m (13.1ft)
SP4SS/3 4.0m (13.1ft)
Double Socket Cat. No. Dimensions Sizes
Z1 82 110 160
(3) (4) (6)
S1 6
S1/3 4
S1/6 0
Double Solvent Socket Cat. No. Dimensions Sizes
Z1 82 110 160
(3) (4) (6)
S121 2
Drain Connector to C.l. Soil/BS416 Socket. Used with gaskin and cold Cat. No. Dimensions Sizes
caulking compound L 82 110 160
(3) (4) (6)
S4/A 92
Pipe Fixing Bracket Quickfix Cat. No. Dimensions Sizes
A 82 110 160
(3) (4) (6)
S5 92
S5/3 81
Pipe Fixing Bracket Nut and Bolt Cat. No. Dimensions Sizes
Socket Fixing Bracket Nut and Bolt A Type 82 110 160
(3) (4) (6)
S5/6 126 Pipe
S6 82 Socket
S7 92 Pipe
6
SOIL AND VENTILATION SYSTEMS
Pipe or Socker Fixing Bracket Rust Protected Cat. No. Dimensions Sizes
A 82 110 160
(3) (4) (6)
S8 92
S8/3 81
S8/6 126
Barrel Clip for use with “drive-in” spike (RP10) for fixing soil pipe to Cat. No. Dimensions Sizes
masonry, brickwork or rendered buildings A 82 110 160
(3) (4) (6)
S11/3
Bends 871/2 o 76o 671/2o 45o Cat. No. Dimensions Sizes
Bends are spigot tail. For socket tail Angleo Z1 Z2 L 82 110 160
add ‘ST’ suffix to order (3) (4) (6)
S12 87 ½ 138 123 65
S12/3 87½ 111 87 60
S12/6 87½ 111 115 76
S13 76 100 95 65
S14 67½ 116 94 65
S14/3 67½ 84 61 60
S14/6 67½ 76 92 76
S15 45 27 31 65
S15/3 45 22 28 60
S15/6 45 100 37 76
Top Offest Bend Cat. No. Dimensions Sizes
Z1 Z2 82 110 160
(3) (4) (6)
S15A 49 31
S15A/3 39 28
S15A/6 33 38
Bottom Offset Bend Cat. No. Dimensions Sizes
Z1 Z2 L 82 110 160
(3) (4) (6)
S15B 27 36 65
S15B/3 22 38 60
S15B/6 34 37 110
Branch 871/2o 76o 671/2o 45o Cat. No. Dimensions Sizes
Branches include moulded shoulders for bossing
Angleo Z1 Z2 Z3 L 82 110 160
with S101, S102 or S103 Adaptors. (3) (4) (6)
S24 87 ½ 74 79 55 65
S24/3 87½ 110 93 41 60
S24/6 87½ 123 155 85 137
S24/6x4 87½ 119 160 59 110
S25 76 110 96 82 65
S25/3 76 89 73 62 60
S26 67½ 115 95 94 65
S26/3 67½ 84 67 68 60
S27 45 30 163 163 65
Single Unequal Branch Cat. No. Dimensions Sizes
Bossed Z1 Z2 L 82 110 160
Suitable for connection to Push-fit or Solvent
(3) (4) (6)
Waste Systems
S30 56(2”) 45 44 55 65
S30/3 56(2”) 50 50 60
S31 43(1 ½ ”) 45 44 55 65
S31/3 43(1 ½ ”) 38 47 60
S32 36(1 ¼”) 45 44 55 65
S32/3 36(1 ¼”) 30 47 60
Adaption to 40mm and 50mm OD pipe
S30/M 50 45 44 55 65
S30/3M 50 50 50 60
S31/M 40 45 44 55 65
S31/3M 40 38 47 60
7
SOIL AND VENTILATION SYSTEMS
Unequal Branch 3 Way Bossed Pipe Cat. No. Dimensions Sizes
82 110 160
All bosses moulded solid Z1 Z2 L (3) (4) (6)
S33 42 44 65
S33/3 38 47 60
Solvent Three Way Short Boss Pipe Double Socket Cat. No. Dimensions Sizes
Centre Boss drilled. Height can be adjusted by using either way up. Z1 Z2 L 82 110 160
(3) (4) (6)
S35 70.5 91 35
Double Branch *87 1/2 o *76o *671/2 o 45o Cat. No. Dimensions Sizes
*Branches include moulded shoulders for bossing with Angleo Z1 Z2 Z3 L 82 110 160
S101, S102 or S 103 Adaptors (3) (4) (6)
S40 87 1/2 124 64 115 65
S43 45 40 164 164 65
S40/6x4x4 87 1/2 119 58 160 110
Access Bend 87 1/ 2
o
Cat. No. Dimensions Sizes
Z1 Z2 L 82 110 160
(3) (4) (6)
S83 138 123 65
8
SOIL AND VENTILATION SYSTEMS
Loose Skirt Weathering Collar Cat. No. Dimensions Sizes
A 82 110 160
(3) (4) (6)
S85 60
S85/3 60
Balloon Grating Cat. No. Dimensions Sizes
Z1 L 82 110 160
(3) (4) (6)
S86 40 34
S86/3 38 38
Level Invert Reducers Cat. No. Dimensions Sizes
Reduce to Z1 L 82 110 160
(3) (4) (6)
S93 82 (3”) Rubber
S94 82 (3”) 11 68
S94/3 50(2”) 7 60
S94/6 110(4”) 75 75
9
SOIL AND VENTILATION SYSTEMS
Straight W.C. Connectors Cat. No. Dimensions Sizes
Z1 L 110
(4)
S61 4 152 (6)
S63 4 305 (12)
S65 4 457 (18)
S67 4 610 (24)
S210 Solvent Socket 4
Horizontal Outlet W.C. Pan Connector 14o Bend, Spigot Tail Cat.No. Dimensions Sizes
Z1 Z2 L 110
(4)
S120 13 13 62
Horizontal Outlet W.C. Pan Connector 2 1/2o Bend. Spigot Tail Cat.No. Dimensions Sizes
For Socket add ‘ST’ suffix to Cat. No. Z1 L 110
(4)
S130 20 60
10
SOIL AND VENTILATION SYSTEMS
Horizontal Outlet W.C. Pan Connector Cat. No. Dimensions Sizes
90o bend, Spigot Tail. For socket tail add ‘ST’ Z1 Z2 L 110
suffix to order. (4)
S140 102 60 65
Double Solvent Socket Spigot to Solvent Socket Adaptor (White) Cat. No. Dimensions Sizes
(For extending Pan Connectors) Z1 110
(4)
S121/W 2
11
THE HEPWORTH SOIL MANIFOLD
FIXING INSTRUCTIONS
The soil manifold is designed to fit neatly into the corner Connection to the waste inlets is made by removing the
of a room shown in the schematic layouts (figs .2 and 3). plug from the inlet port required and simply push fitting
Dimension X represents the standard clipping distance the waste pipe or fitting into the Manifold until the stop is
from the walls, which for 110 mm pipe is 92 mm. reached. Plugs should not be removed from unused
ports.
Alternatively the Manifold readily adopts to ground floor This process is further simplified by the unique Universal
assemblies as shown in fig. 4. Seal which will accept a range of waste pipes in 32 mm
The tricorn shape allows final adjustment within the right (1 ¼”) and 40 mm (1 ½”) sizes to both BS5254 and
angle depending on the direction of the connecting BS5255 sizes. 50 mm inlets are provided as standard
waste pipes. Waste connectors into the Manifold can be and any combination of inlets is possible giving
horizontal using swivel elbows or vertical as required. complete flexibility and freedom to the installer.
It is also possible to raise or lower the Manifold in
relation to the floor level if required by suitable packing
The Manifold allows sufficient space to connect beneath
beneath the locating ledge.
the connecting branch as shown in Pic. 1.
Soil Manifolds can be fitted neatly side by side where
Use the template provided with each fitting to mark out
central ducts are used, whilst maintaining direct access
the required position of the Manifold on the floor, then
to all inlets and utilizing the minimum of space. Correct
cut out the shape using a padsaw. Where the floor is not
use of the Soil Manifold can eliminate the need for
is situ the Manifold can be supported beneath the ledge
unsightly runs of waste pipe on external walls (fig. 5)
provided using stretchers.
allowing internal waste connections even on external
Connection to the 110 mm inlet can be made in the stacks. The Manifold can also be fitted at the foot of an
normal way by push-fitting pipe or fitting spigot into the external stack for use as an alternative to a gully.
Plumbing in a complete bathroom can now be much seal. Lubricate the seal prior to assembly.
quicker, with the Soil Manifold, and idea so simple, yet
so obviously useful. A fitting that allows the connection
of all soil and waste pipes above floor level.
Fig. 2
Internal 1st floor soil stack connection (plan)
Fig. 3
Internal 1st Floor soil stack connection (elevation)
Fig. 4
Internal ground floor w/c connection
Fig. 5
External 1st floor soil stack connection
Fig. 6
External ground floor waste pipe connection
12
THE HEPWORTH DEEP SEAL FLOORING GULLY
Fixing Instructions
The gully should be installed on a firm base and located
relative to the floor finish. The method of fixing will be
dependent on the type of floor finish.
Depth of installation other than that accommodated by the
standard gully can be obtained by using the extension
socket (S417), and an off-cut of 110mm diameter pipe of
appropriate length. In this way any depth required can be
achieved.
The depth of seal is maintained by either extending the
funnel piece with 40mm ABS waste pipe to BS5255, or, by
solvent cementing a trap bowl (S415) to the funnel piece
(S418). The depth can be reduced by cutting the collar down
to the nearest groove and trimming. The overall depth can be
reduced to 125mm in this way.
The tile and grid is fixed in position by either the overlap of the
tile grouting or the surrounding floor finish. The lid can be
removed by pushing down on one edge, and the perforated
grid removed by levering off with a screwdriver or coin. The
grid is fixed by pushing firmly into position. The protective
plastic film should be left in position until completion of the
final floor finish to avoid damage.
Inlets should be drilled using a 60mm (23/8”) hole saw. The
funnel piece (S418) should be removed from the fitting before
drilling. Care should be taken to avoid damage to the boss
shoulders.
Waste pipe connections to the boss shoulders can be
effected in two ways:
1) By using solvent boss adaptors (S101. S102. S103 etc)
and solvent cementing into position in the usual way. The
boss adaptors are pitched at 2 ½o and should be fixed
with the top uppermost as indicated by the arrows.
The joint should be left for at least 10 minutes, and allowed
24 hours for the joint to attain maximum strength.
2) By using the new rubber inserts S420, S421, S422, S423
and simply inserting dry into the boss shoulder. All
standard sizes of plastics and copper waste pipes can be
accommodated in this way.
The standard seal depth (50mm) of the gully can be
increased by the removal of the base with a saw, leaving
sufficient spigot to solvent cement a trap extension b o w l
(S416) into position. The funnel piece (S418) can then be
extended with 40mm ABS waste pipe to BS5255 to give a
nominal 80mm seal depth. The seal depth can be further
increased by the addition of a piece of 8 2 m m s o i l p i p e
between the base and the bowl and extending the funnel
piece with 40mm ABS waste pipe to BS5255 to achieve
any seal depth required.
The funnel piece (S418) and trap bowl (S415) can be used
together with many standard 110mm fittings to provide a
trap arrangement; (see back cover). F o r e x a m p l e , i n
o
conjunction with a 92 ½ bend S12 of a single socket S2,
to give a trapped balcony/roof outlet. See back cover. The
floor gully can be extended using standard 110mm boss
pipe fittings to provide extra boss inlets. Care should be
taken in all combinations to press the funnel (S418) fully
home to give required depth of seal.
Metric conversion rings are available f o r a l l b o s s
connections allowing inlet connection of 30mm, 40mm
and 50mm waste pipes. The 82mm outlet can be sleeved
with 82mm s o i l p i p e t o g i v e a 7 5 m m s o c k e t t o
accommodate 75mm diameter outlet pipes.
Many different combinations are possible, see back cover
for some typical arrangements.
Note: The S414 is not suitable for sheet vinyl floors.
Specially modified gully and grid can be made to order.
13
Design Recommendations for Maximum capacity and number of discharge
Single Stack Plumbing units for vertical stacks
Wash Size, Approximate Approximate
Bath Sink W.C.
basin mm capacity of stack, l/s number of
discharge units
Trap P P P S or P
50 1.2 10*
Depth of Seal Minimum Minimum Minimum Minimum
65 2.1 60*
75mm (3”) 75mm (3”) 75mm (3”) 50mm (2”)
75 3.4 200 t
Height of 0.622m 0.787m 0.900m 0.406m 90 5.3 350
Appliance (2’0 1/2 ”) (2’7”) (3’0”) (16”) 100 7.2 750
Height of 140mm 521mm 546mm 190mm 125 13.3 2500
Trap Outlet (5”) (1’8 1/2”) (1’9 1/2”) (7 1/2”) 150 22.7 5500
Angle of (2 1/2 o) 2 1/2 o 2 1/2 o
Outlet * No WCs. t Not more than one siphonic WC with a 75mm outlet
NOTE Ventilating stacks may be required and sizes are shown below
Pipe Min. size 40mm 32mm 40mm 75mm (3”)&
(1 1/2”) (1 1/4”) (1 1/2”) 102mm (4”)
Maximum
3m 1.7m 3m 6m
Length
Recommended Between Between Between Minimum Maximum number of discharge units allowed
Fall 1o and 5o 1o and 5o 1o and 5o 1o
on branch discharge pipes
Connection No connection within Preferably Branch
to Main area 200mm (8”) below via Boss should have
Stack the intersection of Pipe with a swept DISCHARGE UNITS
the centre lines of expansion entry
branch joint Size, Gradient 1 1/4o 2 1/2o
mm 1 / o (9mm/m) (22mm/m) (45mm/m)
2 NOTE
Notes Flat bottom With the Flat bottom 75mm (3”)
tends to exception tends to usual 32 - 1 1 Discharge
trickle fill of heights trickle fill syphonic 40 - 2 8 pipes sized
Trap this data Trap 50 - 10 26 in this way
can be 65 - 35 95 give the
used for 75 - 100 230 minimum
bidet 90 120 230 460 size
100 230 430 1050 necessary
Discharge unit values and flow rates for 125 780 1500 3000 to carry the
common appliances 150 2000 3500 7500 expected
flow load.
Type of Frequency of use, Discharge NOTE Ventilating pipes may be required and sizes are
appliance min units shown below
WC (9 litres) 20 7
10 14
5 28 General guide for the sizes of ventilating
Wash basin 20 1 pipes and stacks
10 3
5 6 Size of branch discharge pipe Size of branch ventilating
or discharge stack D pipe of stack
Spray tap basin* - Add 0.06 litre/s per tap -
Smaller than 75mm 2 /3 D (25mm min.)
Bath 75 (domestic) 7
30 (commercial 75mm and above 1 /2 D
and congested) 18
Shower - Add 0.1 litre/s per spray -
Washing Mashine
(automatic) 250 4 TABLE OF PIPE DIMENSIONS
Sink 20 6 Nom. Size Systems Mean O.D. Mean I.D.
10 14 mm inch mm inch
5 27 21.5 (3/4 ) Overflow Push-fit 21.56 0.849 19.2 0.756
Urinal 20+ (commercial 21.5 (3/4 ) Overflow Solvent 21.56 0.849 19.2 0.756
(per person) and congested) 0.3
32 (11/4 ) Push-fit Waste 34.6 1.362 30.6 1.205
One group
consisting of 40 (11/2 ) Push-fit Waste 41.0 1.614 36.8 1.449
one WC, one bath, 50 (2) Push-fit Waste 54.1 2.130 49.7 1.957
one or two basins 32 (11/4 ) Solvent Waste 36.3 1.429 32.3 1.272
and one sink 14
40 (1 1/2 ) Solvent Waste 42.9 1.689 38.7 1.524
* Some proportion of the total may be assumed to be insimultaneous
50 (2) Solvent Waste 55.9 2.201 51.5 2.028
operation if considered appropriate.
82 (3) Soil 82.6 3.252 76.0 2.992
t Frequency of flushing of automatic flushing cistern.
110 (4) Soil 110.2 4.339 103.6 4.079
NOTE:
Unless otherwise stated, the frequencies given above represent the 160 (6) Soil 160.3 6.311 153.5 6.043
following:
20min corresponds to peak domestic use,
10 min corresponds to peak commercial use,
5 min corresponds to congested use in public toilets,
schools, etc.
14
FIXING INSTRUCTIONS
JOINTING SOIL SYSTEM INSTALLATION Recommended Hole Cutter
Push-fit Systems Mark the position of brackets, drill and Diameter
Ensure pipe is cut square and chamfered screw fix prior to erecting the stack. Start
from the base of the stack and work up. Cat. No. Cutter Dia.
prior to assembly with fittings.
Use S5 or S7 pipe brackets in conjunc- S101 60 (2 3/8)
Lubricate pipe and fitting with SILICONE tion with S6 socket brackets. On S102 60 (2 3/8)
Lubricant S254 and push-fit to full socket multi-storey installations, use S8
depth. Withdraw pipe 5mm on waste galvanised metal brackets on both pipe
S103 60 (2 3/8)
system and 10mm on soil system to and sockets. S105 38 (1 ½)
allow for expansion. Soil fittings with S106 45 (1 ¾)
spigot ends should be inserted into
Drain Connection S95 67 (2 5/8)
sockets to depth marks engraved on
spigot. This procedure automatically 1. HEPWORTHS Plastic and Clay S95/3 57 (2 ¼)
allows for expansion. Underground drainage systems, S96/3 57 (2 ¼)
Plastidrain, Supersleve, Hepsleve, S97/3 57 (2 ¼)
Anchor fittings with a socket bracket to Hepseal are supplied with connectors
maintain expansion allowance. No to the soil and waste system. S420 60 (2 3/8)
expansion need be allowed on push-fit S421 60 (2 3/8)
overflow system.
2.The S4 is used to connect to old clay S422 60 (2 3/8)
Solvent Weld Systems U.G.D. Systems. Using a sand and Metric W.C. Connection
Ensure pipe is cut square before assem- cement compound, cement S4 into A range of horizontal outlet pan connec-
bly with fittings. the clay collar ensuring that the top of tors is available for fixing to metric pans
the connector is above floor level to
Use H.B.P. Cleaning Fluid on BOTH as specified in BS5503. These are
allow expansion of the pipework.
surfaces to be joined. This removes all supplied with an integral sealing
dirt and machine release agents and diaphragm which allows for up to 5
o
softens the surface ready for the chemi- 3. CAST IRON: The S4A is designed to
connect to cast iron U.G.D. Systems. misalignment in any direction.
cal solvent weld. Failure to do this can Imperial W.C. Connection
result in joint failure. Use gaskin in bottom third of cast iron
socket and make joint using cold A range of pan connectors is available to
Apply solvent cement evenly over mating caulking compound such as PC4. meet the varying pan spigot outside
surfaces of both pipe and socket. Insert diameters. These are push-fit connec-
pipe into socket with slight twisting action tors, allowing easy removal in the event
to full socket depth. of the W.C. pan becoming defective at a
Waste Pipe Connection later date. The polyflex pan connector is
Surplus cement should be removed with particularly adaptable because it allows
A range of solvent-on bosses with
a cloth. The joint should be firm enough to o
for up to 5 misalignment in any direction.
push-fit joints allow connections of the
handle in 5 minutes. Please observe the
waste pipe systems to the stack. Shrink-on Connection
safety precautions detailed on each can.
a) SOIL BOSSES S101, S102 and S103: Fit a replacement soil ring (S360/3 or
NOTE: There is a small gap between the Soil fittings are provided with S360) in a reverted manner onto the cast
O.D. of the pipe and the I.D. of the fitting. shoulders to accept soil bosses. Drill iron pipe spigot i.e. flat edge towards
This is to allow sufficient solvent cement pipe. Fit the blown socket of the shrink-
out the centre of the shoulder and on connector over the seal and apply
into the joint to make a good weld. attach using solvent cement. gentle heat until the socket reverts and
Expansion of pipework should be b) CLIP BOSSES AND PATCH BOSSES shrinks onto the cast iron pipe. This will
allowed for by incorporating expansion S105, S106 and S95: Allows Waste compress the ring and form a watertight
Pipe connection to soil pipe. Drill the seal. The cast iron spigot should have a
couplings at predetermined lengths in relatively smooth surface before making
long pipe runs. pipe where required and solvent weld
the boss in position. the joint
The pipe run should be clipped adjacent c) BOSS ADAPTORS, S420 S421 S422.
to the expansion couplings. No expan- Are for use with the S35 solvent three Roof Weathering
sion need be allowed on the solvent- way short boss pipe, or the S410 The ‘MULTIPITCH’ ROOF WEATHER-
weld overflow system. S410m S412 S412m deep seal floor ING SLATE has been designed to
Traps gully only. provide an easy and effective seal
Jointing of traps to waste outlets. Use between either 82.4mm (3”) or 110mm
(4”) soil pipes. It is suitable for use on a
washer supplied do not over tighten the o o
nut (hand tight plus 1/8 turn). No other variety of roof pitches from 10 to 55
jointing compound or materials should and is capable of being dressed to the
be used. most severe roof-tile profiles.
‘P’ traps can be converted to ‘S’ pattern
by means of BW50/W and CW50/W
conversion bends. Traps are available
with either push-fit or compression
outlets as previously described. All traps
are provided with a means of access
where required.
SUPPORT
The table below shows recommended
maximum centres of support of pipework.
Soil Waste Overflow
Horizontal 1.00m 0.75m 0.75m
Vertical 2.00m 1.50m 1.50m
Fix clips and brackets using rustproofed c/sk
screws. Use No. 8’s on waste and overflow
systems and No. 10’s on soil system.
17
HEPWORTH PUSH-FIT SYSTEM SOIL AND WASTE
18
PUSH-FIT WASTE SYSTEMS
Description Dimension Effect of Solar Radiation
Hepworth Push-fit Waste Systems are AP BP CP Polypropylene is affected by ultra-violet
manufactured in 32mm (1 ¼”), 40mm Nom size 1 ¼” light and the painting of external
1 ½” 2”
(1½’’), and 50mm (2”) nominal sizes in pipework is recommended. (Internal
Actual mean OD 34.6 41.0 54.1 pipework is not affected).
polypropylene. Wall thickness min 1.80 1.90 2.00
A significant feature of the Hepworth Length 3m 3m 3m
System is the patented Push -fit jointing Effect of Frost
method. An ‘O’ ring seal is retained in a Weight Frost does not affect the operation of
moulded housing by a snap-in end clip. the systems; sub-zero temperatures,
32mm pipe = 0.185 Kg/m : (mean)
This gives a simple, positive Push-fit however, reduce the impact strength.
40mm pipe = 0.232 Kg/m : (mean)
sealing action and incorporates an 50mm pipe = 0.326 Kg/m : (mean)
allowance for thermal movement of the Flammability
pipework at each joint. Effect of Chemicals Flammability = 1 inch per minute. Test
Waste Socket Detail Polypropylene has a high chemical method BS2782 Method 508A.
resistance and is unaffected by boiling
water. It is resistant to most organic Model Specification
P.P. Pipe acids, alkalis and aqueous solutions
though subject to attack by oxidising All waste systems to be Push-fit ring
acids and concentrates. For specialised seal type to BS5254 manufactured in
applications, consult our Technical polypropylene by Hepworth Building
P.P. Retaining Clip
‘O’ Ring Seal
Services Department for advice. Products and fitted in accordance with
P.P. Pipe Socket their instructions.
Reaction with other Materials
Z Dimensions
Polypropylene has not been found to
The ‘Z’ dimension is the distance from
react adversely with any traditional
the centre line of the fitting to the point
building materials.
reached by the pipe end when fully
Varifix Socket Detail engaged.
Maintenance
Designers should provide adequate With some fittings, such as adaptors,
access for periodic cleaning. It is the ‘Z’ dimension is measured from he
advisable to paint pipes fixed externally face, not the centre, but the urpose is
P.P. Retaining Clip
for protection against the effects of the same, that is, to provide a simple
‘O’ Ring Seal
strong sunlight. method of calculating the length of
pipework required, and is demonstrated
in the drawing below.
Socket accepts
P.P./ABS/Metnc/
Prefabricated Items
Imperial Copper Pipe
For particular installations that require
special products, a prefabrication
Standards service is available. Information on
these items is available through the
The Hepworth Push-fit Waste Systems,
Technical Services Department.
where applicable, conform to the stand-
ards laid down by BS 5254 and are
Colour
entitled to carry the Kitemark. Ring
seals comply with BS 2494 / BN 681 – 1. 32mm and 40mm sizes available in PIPE LENGTH
CENTRE TO CENTRE
grey, black, brown and copper. 50mm
See note on quality assurance.
size available in grey only.
PIPE LENGTH
Application Thermal Movement OVERALL LENGTH
19
PUSH-FIT WASTE SYSTEMS
Plain Ended Pipe Cat. No. Dimensions Sizes Bend 150 Waste to Dimensions Sizes
Length 32 40 50 Soil Connector Z1 Z2 L 32 40 50
(1 1/4 ) (1 1/2) (2) Cat. No. (1 1/4 ) (1 1/2) (2)
BP3 3m (9.8ft) BW51 44 9 38
CP3 3m (9.8ft) CW51 47 7 39
DP3 3m (9.8ft) DW51 33 11 39
Straight Connectors Cat. No. Dimensions Sizes Knuckle Bend 90 o Cat. No. Dimensions Sizes
Z1 32 40 50 Z1 Z2 32 40 50
(1 1/4 ) (1 1/2) (2) (1 1/4 ) (1 1/2) (2)
BW1 3 BW11 20 20
BW1/V 3 CW11 23 23
CW1 3 DW11 27 27
CW1/V 3
DW1 3
DW1/V 3
V denotes Varrifix Sockets
Swept Bend 92 1/4 o Cat. No. Dimensions Sizes
Socket Reducers Dimensions Sizes Z1 Z2 32 40 50
Reduce to L 32 40 50 (1 1/4 ) (1 1/2) (2)
Cat No. (1 1/4 ) (1 1/2) (2) BW12 43 43
AO8 21.5 ( 3/4 ”) 30 CW12 46 46
AO9 21.5 ( 3/4 ”) 30 DW12 55 55
CBW2 32 (1 1/4 ”) 39
DBW2 32 (1 1/4 ”) 44
DCW2 40 (1 1/2”) 44
Tank Connector with back nut Dimensions Sizes Swlvel Elbow 92 1/2o Waste to Dimensions Sizes
Z1 L 32 40 50 Z1 Z2 L 32 40 50
Cat. No. (1 1/4 ) (1 1/2) (2) Cat. No. (1 1/4 ) (1 1/2) (2)
BW4 3 24
CW4 3 BW50 38 26 38
24
CW50 37 26 39
DW50 37 32 41
Bend 135o Cat. No. Dimensions Sizes Pipe Clip Cat. No. Dimensions Sizes
Z1 Z2 32 40 50 A 32 40 50
(1 1/4 ) (1 1/2) (2) (1 1/4 ) (1 1/2) (2)
BW10 10 10 BW17 27
CW10 12 12 CW17 27
DW10 15 15 DW17 35
20
SOLWELD
SOLWELD
Solvent Weld Waste Systems
S l t W ld W t St
Flammability
Flammability = 1.3 inches per minute.
Test method BS2782 508A.
21
SOLWELD
Solvent Weld Waste Systems
22
SOLWELD
Solvent Weld Waste Systems
Cross 921/2 O
Catalogue No. Dimensions Sizes
Z1 Z2 Z3 32 40 50
(1 1 / 4 ) (1 1 / 2 ) 2
SCW31 34 34 21
SDW31 42 42 28
23
TRAPS AND FITTINGS
Description
Hepworth traps are injection moulded in specially formulated, high temperature polypropylene, to give a smooth bore, and
accurate wall thickness. The compact outlets are designed to give maximum versatility and flexibility, to ease installation in
confined spaces. Traps are manufactured in white polypropylene in 32mm (1 ¼ ”) and 40mm (1 ½ ”) nominal sizes, for
connection to 1 ¼’’ and 1 ½’’ BSP standard waste outlets. The range includes tubular bottle, swivel neck, and anti syphon
types. Traps are supplied with washers to BS 2494.
Trap Outlets
A choice of either Push-fit Varifix outlet or universal compression outlets is
available.
Both will accept Push-fit or solvent, plastics pipe work to BS5254 or BS5255 and
imperial or British “metric” copper.
Varifix traps can be supplied with outlets for connection 40mm I.S.O. metric
pipe.
BARVAC TRAP
Anti -syphon Trap for automatic
protection from syphonage
problems associated with waste
discharge systems. The Trap is self-
cleaning, has no moving parts and
has a flow rate in excess of that
required by BS3943.
Principles of Operation
Fig. 1 : Shows the Barvac trap under
normal operating conditions with full
water seal.
Fig. 2: When subjected to severe
Performance syphonage conditions the Barvac
automatic hydraulic action allows air
The traps are manufactured to meet all the requirements of BS3943. through the by-pass tube without
All Hepworth traps have seals to the requirements of BS 2494 / BN 681-1 any major loss of water.
Special design features give high flow rates and the bowl is removable for easy Fig. 3: When normal conditions
access and cleaning. return the remaining water falls back
to re-seal the trap.
32mm (1 ¼ ”): 50 litres/minute.
40mm (1 ½” ): 67 litres/minute.
Normal deep seal : 85mm.
Minimum seal possible after syphonage (extreme conditions): 40mm.
24
TRAPS AND FITTINGS
Waste Traps with Push-Fit Varifix Outlets
Tubular
Tubular‘P’
‘P’Outlet
Oultlet Catalogue No. Dimensions Sizes
Swivel Z1 Z2 Z3 32 40
3”-76mm seal (1 1/4 ) (1 1/2)
BT24 130 104 8
CT24 140 118 8
Tubular
Tubular‘P’
‘P’Outlet
Oultlet Catalogue No. Dimensions Sizes
Swivel Z1 Z2 Z3 32 40
3” -76mm seal (1 1/4 ) (1 1/2)
c/w cleaning eye CT44 150 105 1
Tubular‘Running’
Tubular ‘Running’ Catalogue No. Dimensions Sizes
Swivel Z1 Z2 Z3 32 40
3” - 76mm seal (1 1/4 ) (1 1/2)
CT27 161 126 18
Tubular
Tubular‘S’
‘S’Outlet
Outlet Catalogue No. Dimensions Sizes
Swivel Z1 Z2 Z3 32 40
3” - 76mm seal (1 1/4 ) (1 1/2)
BT25 137 127 73
CT25 150 127 86
Bottle
Bottle‘P’
‘P’Outlet
Outlet Catalogue No. Dimensions Sizes
Z1 Z2 Z3 32 40
(1 1/4 ) (1 1/2)
1 1/2”-38mm seal BB30t 89 43 43
CB30t 91 39 46
3”-76mm seal BB31t 168 43 43
CB31t 174 39 46
Bottle‘P’
Bottle ‘P’Anti-syphon
Anti-syphon Catalogue No. Dimensions Sizes
Barvac Z1 Z2 Z3 32 40
3”-76mm seal (1 1/4 ) (1 1/2)
BB35 149 43 43
CB35t 151 43 47
25
TRAPS AND FITTINGS
Waste Traps with Universal Compression Outlets
26
TRAP ANCILLARIES
Washing Machine Tee Catalogue No. Dimensions Sizes
Z1 L 32 40
(1 1 / 4 ) (1 1 / 2 )
CT40 54 15
Z1
BW6* 46 38
Z1 CW6* 45 39
27
TRAP ANCILLARIES
PLUMBING KIT. 1 To Suit : 1 ½ Bowl With Drainer
Washing Machine
Or Dishwasher Half Bowl Connector
Outlet
Remove Blank
Plug When Connecting
To Washing Machine
Or Dishwasher
Washing Machine
Or Dishwasher Full Bowl Connector
Outlet
Remove Blank
Plug When
Connecting To
Washing Mashine
Or Dishwasher
28
OVERFLOW SYSTEMS
Push-fit and Solvent Weld Overflow Systems
Description
The Hepworth overflow systems are manufactured in
21.5mm ( 3/4 ”) size in either grey or white polypropylene (push-fit)
or white ABS (solvent weld).
NOTE: PRE-FIX ‘S’ indicates solvent weld.
Plain Ended Pipe Cat. No. Dimensions Sizes Socket Adaptors (Rubber) Cat. No. Dimensions Sizes
Length (L) 21.5 Reduce from L 21.5
( 3/4 ) ( 3/4 )
AP3 3m (9.8ft) AO8 32 (1 1/4 ”) 30
SAP3 3m (9.8ft) AO9 40 (1 1/2” ) 30
Straight Connector Cat. No. Dimensions Sizes Knuckle Bend 90o Cat. No. Dimensions Sizes
Z1 21.5 Z1 Z2 21.5
( 3/4 ) ( 3/4 )
AO1 2 AO11 11 11
SAO1 2 SAO11 11 11
Tank Connector Straight Cat. No. Dimensions Sizes Bend 155o Cat. No. Dimensions Sizes
Z1 L 21.5 Z1 Z2 21.5
( 3/4 ) ( 3/4 )
AO4 3 29 AO12 7 7
SAO4 3 29
29
Hepworth BUILDING PRODUCTS
.....
............
CLAY DRAINAGE Sewerdrain
PVC-U gravity drainage in diameters from
160mm to 400mm and 18” to 24”.
TERRACOTTA