Académique Documents
Professionnel Documents
Culture Documents
3
Company: Page: 1
Specifier: Project: DAVE RESIDENCE
Address: 3339 PERALTA BLVD FREMONT Fastening Point:
Phone I Fax: | Date: 02/06/2017
E-Mail:
Specifier's comments:
1 Input data
Anchor type and size: AWS D1.1 GR. B 1/2
Effective embedment depth: hef = 5.000 in.
Material:
Proof: design method ACI 318-08 / CIP
Stand-off installation: eb = 0.000 in. (no stand-off); t = 0.375 in.
Baseplate: lx x ly x t = 6.000 in. x 6.000 in. x 0.375 in.; (Recommended plate thickness: not calculated)
Profile: Round HSS, Steel pipe (AISC); (L x W x T) = 3.000 in. x 3.000 in. x 0.120 in.
Base material: cracked concrete, 2500, fc' = 2500 psi; h = 12.000 in.
Reinforcement: tension: condition B, shear: condition B;
edge reinforcement: none or < No. 4 bar
Seismic loads (cat. C, D, E, or F) no
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.4.3
Company: Page: 2
Specifier: Project: DAVE RESIDENCE
Address: 3339 PERALTA BLVD FREMONT Fastening Point:
Phone I Fax: | Date: 02/06/2017
E-Mail:
3 Tension load
Load Nua [kip] Capacity fNn [kip] Utilisation bN = Nua/fNn Status
Steel failure* N/A N/A N/A N/A
Pull-out failure* N/A N/A N/A N/A
Concrete cone failure** N/A N/A N/A N/A
Concrete side-face blowout, direction ** N/A N/A N/A N/A
* most unfavourable anchor **anchor group (anchors in tension)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.4.3
Company: Page: 3
Specifier: Project: DAVE RESIDENCE
Address: 3339 PERALTA BLVD FREMONT Fastening Point:
Phone I Fax: | Date: 02/06/2017
E-Mail:
4 Shear load
Load Vua [kip] Capacity fVn [kip] Utilisation bV = Vua/fVn Status
Steel failure* 0.003 8.281 1 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout failure** 0.010 30.136 1 OK
Concrete edge failure in direction y+** 0.010 5.645 1 OK
* most unfavourable anchor **anchor group (relevant anchors)
Variables
n Ase,V [in.2] futa [psi]
1 0.20 65000
Calculations
Vsa [kip]
12.740
Results
Vsa [kip] fsteel f Vsa [kip] Vua [kip]
12.740 0.650 8.281 0.003
( )
1
yec,N = 2 e'N 1.0 ACI 318-08 Eq. (D-9)
1+
3 hef
(
ca,min 1.5hef
ycp,N = MAX c , c
ac ac
)
1.0 ACI 318-08 Eq. (D-13)
1.5
Nb = kc l fc hef
'
ACI 318-08 Eq. (D-7)
Variables
kcp hef [in.] ec1,N [in.] ec2,N [in.] ca,min [in.]
2 5.000 0.000 0.000 10.000
Calculations
ANc [in.2] ANc0 [in.2] yec1,N yec2,N yed,N ycp,N Nb [kip]
361.00 225.00 1.000 1.000 1.000 1.000 13.416
Results
Vcpg [kip] fconcrete f Vcpg [kip] Vua [kip]
43.052 0.700 30.136 0.010
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.4.3
Company: Page: 4
Specifier: Project: DAVE RESIDENCE
Address: 3339 PERALTA BLVD FREMONT Fastening Point:
Phone I Fax: | Date: 02/06/2017
E-Mail:
Vcbg = (AA ) y
Vc
Vc0
ec,V yed,V yc,V yh,V yparallel,V Vb ACI 318-08 Eq. (D-22)
f Vcbg Vua ACI 318-08 Eq. (D-2)
AVc see ACI 318-08, Part D.6.2.1, Fig. RD.6.2.1(b)
AVc0 = 4.5 c2a1 ACI 318-08 Eq. (D-23)
( )
1
yec,V = 2e'v 1.0 ACI 318-08 Eq. (D-26)
1+
3ca1
yh,V =
1.5ca1
ha
1.0 ACI 318-08 Eq. (D-29)
(( ) )
0.2
l 1.5
Vb = 7 e da l f'c ca1 ACI 318-08 Eq. (D-24)
da
Variables
ca1 [in.] ca2 [in.] ecV [in.] yc,V ha [in.]
8.000 10.000 0.000 1.000 12.000
Calculations
AVc [in.2] AVc0 [in.2] yec,V yed,V yh,V Vb [kip]
288.00 288.00 1.000 0.950 1.000 8.488
Results
Vcbg [kip] fconcrete f Vcbg [kip] Vua [kip]
8.064 0.700 5.645 0.010
5 Warnings
To avoid failure of the baseplate the required thickness can be calculated in PROFIS Anchor. Load re-distributions on the anchors due to elastic
deformations of the baseplate are not considered. The baseplate is assumed to be sufficiently stiff, in order not to be deformed when subjected to
the loading!
Condition A applies when supplementary reinforcement is used. The factor is increased for non-steel Design Strengths except Pullout Strength
and Pryout Strength.
Condition B applies when supplementary reinforcement is not used and for Pullout Strength and Pryout Strength.
Refer to
your local standard.
Checking the transfer of loads into the base material and the shear resistance are required in accordance with ACI 318 or the relevant standard!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.4.3
Company: Page: 5
Specifier: Project: DAVE RESIDENCE
Address: 3339 PERALTA BLVD FREMONT Fastening Point:
Phone I Fax: | Date: 02/06/2017
E-Mail:
6 Installation data
Baseplate, steel: - Anchor type and size: AWS D1.1 GR. B, 1/2
Profile: Round HSS, Steel pipe (AISC); 3.000 x 3.000 x 0.120 in. Installation torque: 0.000 in.kip
Hole diameter in the fixture: df = 0.563 in. Hole diameter in the base material: - in.
Plate thickness (input): 0.375 in. Hole depth in the base material: 5.000 in.
Recommended plate thickness: not calculated Minimum thickness of the base material: 6.813 in.
Cleaning: No cleaning of the drilled hole is required
y
3.000 3.000
1.000
3 4
3.000
4.000
x
3.000
1 2
1.000
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.4.3
Company: Page: 6
Specifier: Project: DAVE RESIDENCE
Address: 3339 PERALTA BLVD FREMONT Fastening Point:
Phone I Fax: | Date: 02/06/2017
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan