Vous êtes sur la page 1sur 2

Chaitanya Bharathi Institute of Technology (A)

Department of Mechanical Engineering


Mechanics of Materials Lab Internal Exam, Batch-III.
Max Marks: 15

Roll Number:
--------------------------------------------------------------------------
1. In terms of Poisson's ratio () the ratio of Young's Modulus (E) to Shear Modulus (G) of
Elastic materials is
(a) 2(1 + ) (b) 2(1 )
1 1
(b) (1 + ) (d) (1 )
2 2
2. The relationship between Young's modulus (E), Bulk modulus (K) and Poisson's ratio () is
given by:
(a) = 3(1 2)
(b) = 3(1 2)
(c) = 3(1 )
(d) = 3(1 )

3. Which one of the following statements is correct?


A beam is said to be of uniform strength, if
(a) The bending moment is the same throughout the beam
(b) The shear stress is the same throughout the beam
(c) The deflection is the same throughout the beam
(d) The bending stress is the same at every section along its longitudinal axis

4. Match List-I (Elastic properties of an isotropic elastic material) with List-II (Nature of strain
produced) and select the correct answer using the codes given below the Lists:
List-I List-II
A. Young's modulus 1. Shear strain
B. Modulus of rigidity 2. Normal strain
C. Bulk modulus 3. Transverse strain
D. Poisson's ratio 4. Volumetric strain
Codes: ABCD ABCD
(a) 1 2 3 4 (b) 2 1 3 4
(c) 2 1 4 3 (d) 1 2 4 3
5. If the value of Poisson's ratio is zero, then it means that
(a) The material is rigid.
(b) The material is perfectly plastic.
(c) There is no longitudinal strain in the material
(d) The longitudinal strain in the material is infinite.

6. If a piece of material neither expands nor contracts in volume when subjected to stress, then
the Poissons ratio must be
(a) Zero (b) 0.25 (c) 0.33 (d) 0.5

7. A concentrated force, F is applied (perpendicular to the plane of the figure) on the tip of the
bent bar shown in Figure. The equivalent load at a section close to the fixed end is:
(a) Force F
(b) Force F and bending moment FL
(c) Force F and twisting moment FL
(d) Force F bending moment F L, and twisting moment FL.
8. The shear force in a beam subjected to pure positive bending is (positive/zero/negative)

9. The point of contra flexure is a point where:


(a) Shear force changes sign (b) Bending moment changes sign
(c) Shear force is maximum (d) Bending moment is maximum.

10. Consider the following statements: In a cantilever subjected to a concentrated load at the free
end
1. The bending stress is maximum at the free end
2. The maximum shear stress is constant along the length of the beam
3. The slope of the elastic curve is zero at the fixed end
Which of these statements are correct?
(a) 1, 2 and 3 (b) 2 and 3 (c) 1 and 3 (d) 1 and 2

11. The ratio of the moments of resistance of a square beam (Z) when square section is placed (i)
with two sides horizontal (Z1) and (ii) with a diagonal horizontal (Z2 ) as shown is

12. A solid circular shaft of 60 mm diameter transmits a torque of 1600 N.m. The value of
maimum shear stress developed is
(a) 37.72 MPa (b) 47.72 MPa (c) 57.72 MPa (d) 67.72 Mpa

13. The diameter of a shaft is increased from 30 mm to 60 mm, all other conditions remaining unchanged.
How many times is its torque carrying capacity increased?[
(a) 2 times (b) 4 times (c) 8 times (d) 16 times

14. Angle of twist of a shaft of diameter dis inversely proportional to [IES-2000]


(a) d (b) d2 (c) d3 (d) d4

15. A hollow shaft of the same cross-sectional area and material as that of a solid shaft transmits:
(a) Same torque (b) Lesser torque (c) More torque (d) Cannot be predicted without more data

Paper Set By: S.Solomon Raj


Dept.of Mechanical Engineering.

Vous aimerez peut-être aussi