Académique Documents
Professionnel Documents
Culture Documents
Centrifugal Pump
Application Designation
The Ajax Elite centrifugal pump is suitable for handling E 150 - 40 A 20 C
water and similar liquids mainly used in the following Type
applications. Discharge diameter mm
-Water Supply Nominal impeller diameter cm
-Air conditioning Mechanical arrangement
-Irrigation Shaft sealing
-Pressure boosting Materials of construction
-Fire Protection
-Heating and ventilating
-Industrial
Selection Chart
1450 rpm
Note:
For final selection
refer to individual
performance
curves
Selection Chart
2900 rpm
Note:
For final selection
refer to individual
performance
curves
2
Elite
Construction Painting
Horizontal, single stage, end suction with vertical Prior to painting, the pump is thoroughly cleaned of scale,
discharge, complying with the requirements of EN 733 weld splatter and any other foreign material. The pump is
(DIN 24255). Most models are suitable for 1600kPa (16 then painted with a high quality industrial enamel paint.
bar) pressure except for larger pumps that are rated for
1000kPa (10 bar). The pull back out design allows for the Accessories
maintenance of the pump without disturbing the pipework
Drive
connected to the casing, or the pump alignment.
The pump is only recommended for direct drive via a
flexible spacer coupling. Spacer couplings enable the
Flanges utilisation of the back pull out feature.
Pump flanges have raised faces and are to standards Where belt drives are necessary a separate jack
AS/NZS 4331.2, ISO 7005.2 16 bar. Gauge tappings are (intermediate) shaft with bearings to carry the belt loads
provided on suction and discharge flanges as standard. may be required.
Bearings
Pump Selection
For pump selection the hydraulic performance curves
Grease Lubrication Standard
should be used. These curves are based on water at
Oil Lubrication for high speed models (EH)
15oC and SG equal to 1.0.
Max. Pump Temperature 95oC
NPSH values are indicated on the performance curves.
The Bearing arrangement consists of two identical single
At least 0.5m should be added as a safety margin.
row deep groove ball bearings which are grease lubricated
To overcome variations between actual and design
through grease nipples located in each bearing cover.
system requirements it is recommended that the driver
power exceeds the absorbed pump shaft power.
Shaft Seal
The shaft sealing is carried out by means of mechanical
seal with the option of packed gland.
Mechanical Seal - A single mechanical seal, with a
ceramic stationary face and carbon rotating face is fitted as Absorbed Pump Driver Power
standard. The standard seal elastomer is nitrile and is Shaft [kW] Reserve
suitable for up to 95oC temperature applications. The other
seal components are AISI 304 stainless steel. Up to 7.5 Approx. 20%
Options: Balanced seal option M1
7.5 - 40 Approx. 15%
Cyclone separator option S1
Gland Packing - Fitted with removable lantern ring and Above 40 Approx. 10%
square plaited packing. Packing is fitted over the sleeve to
prevent shaft wear.
3
Elite
General Operating Parameters
Mechanical Seal
Packed Gland
Standard Seal Option M1
Pressure Maximum operating pressure* 1600kPa 1400kPa 1400kPa
Maximum hydrostatic test pressure 2100kPa 2100kPa 2400kPa
Maximum suction pressure 1450rpm 600kPa 900kPa 1000kPa
Maximum suction pressure 2900rpm 400kPa 700kPa 1000kPa
Temperature Packed gland -20oC to 95oC
Mechanical Seal: Standard -20oC to 95oC
Mechanical Seal Balanced: Option M1 -20oC to 95oC
Speed Maximum Speed* 3600 rpm
*refer tabular listing on page 5.
Material Specifications
Material Component Nearest Equivalent Standard
Australian British American EN
Cast Iron Casing
Back Cover
Bearing Housing ASTM A48
AS1830/T220 BS1452: GR220 JL 1030
Bearing Cover Class 30
Lantern Ring
Wear Rings (Option)
Zinc Free Impeller BS 1400-1973
Bronze AS1565-1985 ASTM
Wear Rings CT1 CC480 K - GC
Alloy C90250 C 90700
906D
Bronze Lantern Ring Bush AS1565-C83600 BS1400-LG2 ASTM B584-C83600 -
Stainless Steel Shaft AS2837 GR.420 BS970:420/S37 AISI Type 420 X20CR13
Shaft Sleeve AS2837 GR.316 BS970:316 AISI Type 316 X10CRN1MOT118/10
4
Elite
Pump Technical Data
Mass Moment of
Maximum Nominal Inertia J Rotating Hydrostatic Test Pressure Maximum Working Pressure
Bearing Type
Pump Model Speed Direct Coupled Assy. Less Coupling Maximum up to 120C
[kg*m 2]
rpm/imp. dia Front Rear Bronze Impeller bar kPa PSI bar kPa PSI
E32-13 3450/134 6305 6305 0.004 21 2100 304 16 1600 232
E32-16 3450/156 6305 6305 0.006 21 2100 304 16 1600 232
E32-20 3450/181 6305 6305 0.015 21 2100 304 16 1600 232
E32-26 3450/220 6305 6305 0.043 21 2100 304 16 1600 232
E40-13 3450/130 6305 6305 0.004 21 2100 304 16 1600 232
E40-16 3450/156 6305 6305 0.006 21 2100 304 16 1600 232
E40-20 3450/186 6305 6305 0.019 21 2100 304 16 1600 232
E40-26 3450/225 6305 6305 0.048 21 2100 304 16 1600 232
E40-32 2300/329 6307 6307 0.105 21 2100 304 16 1600 232
EH40-32 2900/320 3307 3307 0.105 21 2100 304 16 1600 232
E50-13 3450/132 6305 6305 0.005 21 2100 304 16 1600 232
E50-16 3450/159 6305 6305 0.008 21 2100 304 16 1600 232
E50-20 3450/182 6305 6305 0.019 21 2100 304 16 1600 232
E50-26 3450/227 6305 6305 0.05 21 2100 304 16 1600 232
E50-32 2300/328 6307 6307 0.111 21 2100 304 16 1600 232
EH50-32 2900/314 3307 3307 0.111 21 2100 304 16 1600 232
E65-13 3450/159 6305 6305 0.006 21 2100 304 16 1600 232
E65-16 3450/159 6305 6305 0.009 21 2100 304 16 1600 232
E65-20 3450/184 6305 6305 0.019 21 2100 304 16 1600 232
E65-26 3450/224 6307 6307 0.052 21 2100 304 16 1600 232
E65-32 2400/329 6307 6307 0.127 21 2100 304 16 1600 232
EH65-32 2900/316 3307 3307 0.127 21 2100 304 16 1600 232
E80-16 3450/160 6305 6305 0.013 21 2100 304 16 1600 232
E80-20 3450/191 6307 6307 0.024 21 2100 304 16 1600 232
E80-26 3450/230 6307 6307 0.05 21 2100 304 16 1600 232
E80-32 1800/329 6307 6307 0.107 21 2100 304 16 1600 232
EH80-32 2900/318 3307 3307 0.107 21 2100 304 16 1600 232
E80-40 1800/409 6309 6309 0.392 17 1700 246 13 1300 188
E100-16 2900/174 6307 6307 0.02 21 2100 304 16 1600 232
E100-20 3450/193 6307 6307 0.03 21 2100 304 16 1600 232
E100-26 3450/228 6307 6307 0.068 21 2100 304 16 1600 232
E100-32 1800/329 6307 6307 0.156 21 2100 304 16 1600 232
E100-40 1800/409 6309 6309 0.358 17 1700 246 13 1300 188
E125-20 2900/214 6307 6307 0.069 21 2100 304 16 1600 232
E125-26 1800/264 6307 6307 0.076 21 2100 304 16 1600 232
E125-32 1800/329 6309 6309 0.165 21 2100 304 16 1600 232
E125-40 1800/409 6309 6309 0.377 17 1700 246 13 1300 188
E150-20 1800/220 6307 6307 0.078 15 1500 217 11 1100 159
E150-26 1800/264 6309 6309 0.158 15 1500 217 11 1100 159
E150-32 1800/329 6309 6309 0.182 15 1500 217 11 1100 159
E150-40 1800/409 6309 6309 0.4 15 1500 217 11 1100 159
E200-26 1800/264 6309 6309 0.3 15 1500 217 11 1100 159
E200-32 1800/329 6311 6311 0.217 15 1500 217 11 1100 159
E200-40 1800/409 6311 6311 0.441 15 1500 217 11 1100 159
E250-32 1800/329 6311 6311 0.221 15 1500 217 11 1100 159
E250-40 1800/409 6311 6311 0.451 15 1500 217 11 1100 159
5
Elite
Pump Technical Data
6
Elite
Pump Models with clamped back cover: Pump Models with bolted back cover:
E32-13, E32-16, E40-13, E40-16, E32-20, E32-26, E40-20, E40-26, E40-32,
E50-13, E50-16, E65-13, E65-16, E50-20, E50-26, E50-32, E65-20, E65-26,
E80-16, E80-20, E100-16, E100-20, E65-32, E80-26, E80-32, E80-40, E100-26,
E125-20, E150-26, E200-26 E100-32, E100-40, E125-26, E125-32,
E125-40, E150-20, E150-32, E150-40,
E200-32, E200-40, E250-32, E250-40
* no Expeller Vanes
*Note: Lip Seals fitted to pump models E80-40, E100-40, E125-32, E125-40, E150-32, E150-40, E200-26, E200-32,
E200-40, E250-32, E250-40
**From 1997 O Ring used instead of gasket.
7
Elite
Pump Models with clamped back cover: Pump Models with bolted back cover:
E32-13, E32-16, E40-13, E40-16, E32-20, E32-26, E40-20, E40-26, E40-32,
E50-13, E50-16, E65-13, E65-16, E50-20, E50-26, E50-32, E65-20, E65-26,
E80-16, E80-20, E100-16, E100-20, E65-32, E80-26, E80-32, E80-40, E100-26,
E125-20, E150-26, E200-26 E100-32, E100-40, E125-26, E125-32,
E125-40, E150-20, E150-32, E150-40,
E200-32, E200-40, E250-32, E250-40
* no Expeller Vanes
*Note: Lip Seals fitted to pump models E80-40, E100-40, E125-32, E125-40, E150-32, E150-40, E200-26, E200-32,
E200-40, E250-32, E250-40
**From 1997 O Ring used instead of gasket.
8
Elite
ROTATION
DISCHARGE
Dimensions
FLANGES DRILLED
TO AS/NZS 4331.2
(ISO 7005.2-16bar)
SUCTION
PUMP SHAFT SUCT. DISCH. PUMP FOOT SPACER SHAFT COUPLING NET
SIZE MODULE END KEY WEIGHT
a f h1 h2 b m1 m2 n1 n2 n3 h3 s1 s2 w p y d l [kg]
E32-13 25 50 32 80 360 112 140 50 100 70 190 140 100 14 14 14 267 80 100 24 50 8x7 27
E32-16 25 50 32 80 360 132 160 50 100 70 240 190 100 14 14 14 267 80 100 24 50 8x7 35
E32-20 25 50 32 80 360 160 180 50 100 70 240 190 110 14 14 14 267 80 100 24 50 8x7 41
E32-26 25 50 32 100 360 180 225 65 125 95 320 250 110 14 14 14 267 100 100 24 50 8x7 59
E40-13 25 65 40 80 360 112 140 50 100 70 210 160 100 14 14 14 267 80 100 24 50 8x7 30
E40-16 25 65 40 80 360 132 160 50 100 70 240 190 100 14 14 14 267 80 100 24 50 8x7 36
E40-20 25 65 40 100 360 160 180 50 100 70 265 212 110 14 14 14 267 100 100 24 50 8x7 44
E40-26 25 65 40 100 360 180 225 65 125 95 320 250 110 14 14 14 267 100 100 24 50 8x7 61
E40-32 35 65 40 125 470 200 225 65 130 95 345 280 110 14 14 14 342 125 140 32 80 10x8 96
EH40-32 35 65 40 125 470 200 225 65 130 95 345 280 110 14 14 14 342 125 140 32 80 10x8 96
E50-13 25 65 50 100 360 132 160 50 100 70 240 190 100 14 14 14 267 100 100 24 50 8x7 34
E50-16 25 65 50 100 360 160 180 50 100 70 265 212 110 14 14 14 267 100 100 24 50 8x7 38
E50-20 25 65 50 100 360 160 200 50 100 70 265 212 110 14 14 14 267 100 100 24 50 8x7 46
E50-26 25 65 50 100 360 180 225 65 125 95 320 250 110 14 14 14 267 100 100 24 50 8x7 63
E50-32 35 65 50 125 470 225 280 65 125 95 345 280 110 16 14 14 342 124 140 32 80 10x8 101
EH50-32 35 65 50 125 470 225 280 65 125 95 345 280 110 16 14 14 342 124 140 32 80 10x8 101
E65-13 25 80 65 100 360 160 180 65 125 95 280 212 110 14 14 14 267 100 100 24 50 8x7 39
E65-16 25 80 65 100 360 160 200 65 125 95 280 212 110 14 14 14 267 100 100 24 50 8x7 43
E65-20 25 80 65 100 360 180 225 65 125 95 320 250 110 14 14 14 267 100 100 24 50 8x7 70
E65-26 35 80 65 100 470 200 250 80 160 120 360 280 110 16 18 14 342 100 140 32 80 10x8 81
E65-32 35 80 65 125 470 225 280 80 160 120 400 315 110 16 18 14 342 125 140 32 80 10x8 110
EH65-32 35 80 65 125 470 225 280 80 160 120 400 315 110 16 18 14 342 125 140 32 80 10x8 110
E80-16 25 100 80 125 360 180 225 65 125 95 320 250 110 14 14 14 267 125 100 24 50 8x7 54
E80-20 35 100 80 125 470 180 250 65 125 95 345 280 110 14 14 14 342 125 140 32 80 10x8 70
E80-26 35 100 80 125 470 200 280 80 160 120 400 315 110 16 18 14 342 125 140 32 80 10x8 91
E80-32 35 100 80 125 470 250 315 80 160 120 400 315 110 16 18 14 342 125 140 32 80 10x8 120
EH80-32 35 100 80 125 470 250 315 80 160 120 400 315 110 16 18 14 342 125 140 32 80 10x8 120
E80-40 45 100 80 125 532 280 365 85 160 120 440 340 110 19 18 14 368 132 140 42 110 12x8 161
E100-16 35 125 100 125 470 200 280 30 160 120 340 260 110 16 18 14 342 125 140 32 80 10x8 71
E100-20 35 125 100 125 470 200 280 80 160 120 360 280 110 16 18 14 342 125 140 32 80 10x8 85
E100-26 35 125 100 140 470 225 280 80 160 120 400 315 110 16 18 14 342 140 140 32 80 10x8 106
E100-32 35 125 100 140 470 250 315 80 160 120 400 315 110 16 18 14 342 140 140 32 80 10x8 134
E100-40 45 125 100 140 530 280 355 100 200 150 500 400 110 18 23 14 370 140 140 42 110 12x8 174
E125-20 35 150 125 140 470 250 315 80 160 120 400 315 110 16 18 14 342 140 140 32 80 10x8 106
E125-26 35 150 125 140 470 250 355 80 160 120 400 315 110 16 18 14 342 140 140 32 80 10x8 115
E125-32 45 150 125 140 530 280 355 100 200 150 500 400 110 18 23 14 370 140 140 42 110 12x8 163
E125-40 45 150 125 140 530 315 400 100 200 150 500 400 110 18 23 14 370 140 140 42 110 12x8 181
E150-20 35G 200 150 160 495 280 400 100 200 150 550 450 110 20 23 14 367 160 140 32 80 10x8 156
E150-26 45 200 150 160 530 250 355 100 200 150 450 350 110 18 23 14 370 160 140 42 110 10x8 148
E150-32 45 200 150 160 530 280 400 100 200 150 550 450 110 18 23 14 370 160 140 42 110 12x8 170
E150-40 45 200 150 160 530 315 450 100 200 150 550 450 110 18 23 14 370 160 140 42 110 12x8 209
E200-26 45D 250 200 180 553 315 450 100 200 150 550 450 110 20 28 14 393 180 180 42 110 12x8 206
E200-32 55 250 200 180 670 315 480 120 220 170 600 480 110 20 28 14 504 180 180 48 110 14x9 251
E200-40 55 250 200 180 670 335 480 120 220 170 600 480 110 20 28 14 504 180 180 48 110 14x9 295
E250-32 55 300 250 220 691 355 520 150 250 200 660 510 110 22 28 14 525 220 180 48 110 14x9 311
E250-40 55 300 250 220 682 400 560 150 250 200 660 510 110 22 28 14 516 220 180 48 110 14x9 390
Dimensions shown in mm
9
Elite
Flange Data
Branch Flange Raised Face Drilling*
Bolting
Size D b d1 f N0. d2 k
32 140 18 78 2 4 18 100 M16
40 150 18 88 3 4 18 110 M16
50 165 20 102 3 4 18 125 M16
65 185 20 122 3 4 18 145 M16
80 200 22 138 3 8 18 160 M16
100 220 24 158 3 8 18 180 M16
125 250 26 188 3 8 18 210 M16
150 285 26 212 3 8 22 240 M20
200 340 32 268 3 12 22 295 M20
250 405 32 320 3 12 26 355 M24
300 460 32 378 4 12 26 410 M24
Flange dimensions and drilling according to AS/NZS 4331.2, ISO 7005.2 - 16 bar
(BS4504 - 1969 Table 16/11, DIN 2533 PN16)
Dimensions shown in mm
*Holes - Equally spaced straddling pump centreline
Shaft Dimensions
Shaft Diameter D Key Key Key Seat
KEY LENGTH
Module Nom Tol Length Height Width Depth
KEY WIDTH -0.004
KEY HEIGHT
25 24 32 7 8 20
+0.009
-0.002
35 32 40 8 10 27
SEAT +0.018
DEPTH -0.002
45 42 50 8 12 37
+0.018
-0.002
55 48 80 9 14 42.5
+0.018
Key dimensions are in nominal and expressed in mm
Service Connections
PUMP A B* D S PUMP A B* D S ROTATION
MODEL CASING HOUSING GAUGE GAUGE MODEL CASING HOUSING GAUGE GAUGE
DRAIN DRAIN TAPPING TAPPING DRAIN DRAIN TAPPING TAPPING
E32-13 1/4 3/8 1/4 1/4 E80-26 3/8 3/8 1/4 1/4
E32-16 1/4 3/8 1/4 1/4 E80-32 3/8 3/8 3/8 3/8
E32-20 1/4 3/8 1/4 1/4 EH80-32 3/8 3/8 3/8 3/8
E32-26 3/8 3/8 1/4 1/4 E80-40 3/8 3/8 1/4 3/8
E40-13 1/4 3/8 1/4 1/4 E100-16 3/8 3/8 1/4 3/8
E40-16 1/4 3/8 1/4 1/4 E100-20 3/8 3/8 1/4 3/8
E40-20 1/4 3/8 1/4 1/4 E100-26 3/8 3/8 3/8 3/8
E40-26 3/8 3/8 1/4 1/4 E100-32 3/8 3/8 3/8 3/8
E40-32 3/8 3/8 1/4 1/4 E100-40 3/8 3/8 1/4 3/8
EH40-32 3/8 3/8 1/4 1/4 E125-20 3/8 3/8 3/8 3/8 END ELEVATION
E50-13 1/4 3/8 1/4 1/4 E125-26 3/8 3/8 3/8 3/8
E50-16 3/8 3/8 1/4 1/4 E125-32 3/8 3/8 3/8 3/8 DISCHARGE
E50-20 1/4 3/8 1/4 1/4 E125-40 3/8 3/8 3/8 3/8
E50-26 3/8 3/8 1/4 1/4 E150-20 3/8 3/8 1/4 3/8
E50-32 3/8 3/8 1/4 1/4 E150-26 3/8 3/8 3/8 3/8
EH50-32 3/8 3/8 1/4 1/4 E150-32 3/8 3/8 3/8 3/8 SUCTION
E65-13 1/4 3/8 1/4 1/4 E150-40 3/8 3/8 3/8 3/8
E65-16 3/8 3/8 1/4 1/4 E200-26 3/8 1/2 3/8 3/8
E65-20 3/8 3/8 1/4 1/4 E200-32 3/8 3/8 3/8 3/8
E65-26 3/8 3/8 1/4 1/4 E200-32 3/8 3/8 3/8 3/8
E65-32 3/8 3/8 1/4 1/4 E200-40 3/8 3/8 3/8 3/8
EH65-32 3/8 3/8 1/4 1/4 E250-32 3/8 3/8 3/8 3/8 SIDE ELEVATION
E80-16 3/8 3/8 1/4 1/4 E250-40 3/8 3/8 3/8 3/8
E80-20 3/8 3/8 1/4 1/4 *Left side view from suction
Dimensions shown in inch
10
Elite
NOTE:
Only some models have combination
lantern ring-register bush, check assembly drawing.
MODULE 45 & 55
Module L L1 L2 d d1 d2 k f g Packing
Size No. rings
25 44 30 56 48 32 24 85 M8 35 8 Sq 3
35 53* 40* 63** 60 40 32 100 M10 40 10 Sq 3*
45 63 46 78 75 54 44 110 M12 50 10 Sq 4
55 80 62 62 90 65 53 130 M12 55 13Sq 4
*: models E40-32, E50-32, E65-32, E80-32, E100-32, E100-32, E125-26 L=63, L1=50, No. Rings=4 Dimensions shown in mm
**: model E150-20 L2=83
11
Type Series Booklet Elite
Due to our policy of constant research and development, product specification may change without notice Publication 2007 02/14 1/2K AGP