Académique Documents
Professionnel Documents
Culture Documents
2
TABLE OF CONTENTS
HARD ROCK TOOLING OVERVIEW 5 REAMING TOOLS 69
Bit Types 6 Reamer Bits 70 HARD ROCK TOOLING OVERVIEW 5
Button Bit Face Designs 8 R32 Thread Reamer Bits 70
Reaming Tooling 11 R35 Thread Reamer Bits 70 HANDHELD DRILLING 19
Rod Types 12 HM38 Reamer Bits 71
Thread Types 14 HM45 Reamer Bits 71 DRIFTING AND TUNNELING DRILLING 27
Coupling Types 16
PRODUCTION DRILLING 39
Shank Adapters/Striking Bars 17 Reaming Equipment 72
HANDHELD DRILLING 19 6 degree Reaming Tools 72 REAMING TOOLS 69
12 degree Reaming Tools 72
HANDHELD Rods 20 SHANK ADAPTERS 73
Collared and Tapered Rods 20 SHANK ADAPTERS 73
Rod Shanks 21 Boart Longyear 74 ADAPTER AND COUPLINGS 89
Collared Reaming Rods 22 Cannon 75
NRT Extension Rods 22 Atlas Copco 75 ACCESSORIES 91
Furukawa 78
TROUBLESHOOTING 97
Handheld Bits Gardner Denver 80
Tapered Bits 23 PW 82 CARE AND HANDLING 109
Reaming Equipment 26 Ingersoll Rand 83
DRIFTING AND TUNNELING DRILLING 27 Montabert 83 WARRANTY 115
SCM 84
Drifting and Tunneling Rods 28 SVK 85 PRODUCT INDEX 119
R25Thread Rods 28 Tam Rock 85
R28 Thread Rods 28 CONTACT INFORMATION 125
Toyo 88
R32 Thread Rods 29 UDR 88
R35 Thread Rods 31
ADAPTER AND COUPLINGS 89
Drifting and Tunneling Bits 32 Semi-Bridge Couplings 90
R23 Thread Bits 32 Full Bridge Couplings 90
R25 Thread Bits 32 Full Bridge Adapter Couplings 90
R28 Thread Bits 33
ACCESSORIES 91
R32 Thread Bits 34
R35 Thread Bits 37 Male/ Female Bit Adapters 92
Spiral Male/Female Bit Adapters 92
PRODUCTION DRILLING 39 Male/Female Adapter Guides 92
Production Rods 40 Split Set Drivers 93
R25 Thread Rods 40 Driver Nuts 93
R28 Thread Rods 40 Spears 94
R32 Thread Rods 41 Bell Taps 94
R38 Thread Rods 42 Knock of Blocks 94
HM38 Thread Rods 42 Reaming Shell Adapters 95
HM45 Thread Rods 44 Bit Resharpen Gauge 95
HM51 Thread Rods 46 Cheater Dolly Assemblies 95
BE58 Thread Rods 47 H22 Chuck Gauge 95
EL60 Thread Rods 47 Troubleshooting 97
EL68 Thread Rods 48
Collared and Tapered Rod Failures 98
Collared and Tapered Rod Failures - Socket Ends 99
Production Bits 49
Blade bit Failures 100
HM35 Thread Bits 49
Button Bit Failures 101
HM38 Thread Bits 49
Coupling Failures 104
HM45 Thread Bits 52
Shank Adapter Failures 105
HM51 Thread Bits 55
Drill Steel Failures 107
BE58 Thread Bits 58
EL60 Thread Bits 59 care and handling 109
BE68 Thread Bits 60 Bit Wear Overview 110
EL68 Thread Bits 61 Bit Wear Patterns 111
Product Servicing - Button Bits 112
Production Rod Guides 63 Button Reshaping 112
R32 Thread Rod Guides 63 Product Servicing - Blade Bits 113
HM38 Thread Rod Guides 63 Inspect the Bit Frequently 113
HM45 Thread Rod Guides 63 Gauge Grind Protruding Inserts 113
Blade Bit Sharpening 114
Production Guide Tubes 66
R32 Thread Guide Tubes 66 warranty 115
HM45 Thread Guide Tubes 66
product index 119
HM51 Thread Guide Tubes 66
BE58 Thread Drill Tubes 67 contact information 125
BE68 Thread Drill Tubes 67 3
4
HARD ROCK TOOLING OVERVIEW
Bit Types 6
Button Bit Face Designs 8
Reaming Tooling 11
Rod Types 12
Thread Types 14
Coupling Types 16
Shank Adapters/Striking Bars 17
Copyright 2015 Boart Longyear. All rights reserved.
5
Bit types
OVERVIEW
Button Bit
Fast penetration
More adaptable to different types of ground
conditions, due to the different configurations
of designs and buttons available.
GAUGE FACE
BUTTONS BUTTONS
Outter ring
FLUSHING HOLES
Transport flushing
medium to bit face
Blade Bit
Maintains hole diameter with reduced gauge
wear
Reduced hole deviation
Different types of carbides for different ground
conditions
CHIPWAYS CARBIDE
Provide channels Tent profile
to clear cuttings
from hole
6
Bit types
button bit components
OVERVIEW
FACE
SKIRT LENGTH ANGLE
Gauge
Diameter
SKIRT
DIAMETER
RIBS RIBS
CUTTING EDGES
CUTTING EDGES
7
Button Bit Face Designs
BR - Button Recessed
OVERVIEW
BF - Button Flat
Flat face characteristic
General purpose bit
Hard to medium conditions
BC - Button Chisel
Chisel shape characteristic
Abrasive conditions
Fast penetration
BD - Button Dome
Clearly defined raised face profiles
Primary reaming applications in
soft ground
8
Button Bit Face Designs
Insert Types
OVERVIEW
Hemispherical Button
Best suited to hard ground
25,000 to 45,000 PSI (170 to 300 MPa)
Abrasive to very abrasive
Ballistic Button
Fast penetration
Suited for all non-abrasive ground types
Smaller contact area
Best suited for smaller diameter bits
9
BLADE bit face designs
Cross Bits
Easier to sharpen than X-bits, inset
angles are equal on all four sides
Bits 64 mm and less are easier to sharpen
than button bits of the same size
In certain rock conditions, cross bits tend
to produce a spiraled five sided hole
(especially in diameters larger than
64 mm)
X Bits
X-bits tend to drill round holes in all rock
conditions
The steel support in the narrow parts of
the X becomes inadequate in X-bits
smaller than 64 mm because of the
restricted circumference
10
REAMING TOOLING
Reaming Bits or Hole Openers
OVERVIEW
Description Applications
Pilot holes are drilled to depth and then Large diameter service holes from level
reamed out to a larger diameter in a to level for drainage, electrical cable
second pass or pipe lines
Required when hole diameter exceeds Reaming cut holes for
the capabilities of the rockdrill and development rounds and for long hole
drilling tools available blasting of drop raises
11
ROD TYPES
OVERVIEW
Round Rods
Normally used in extension drilling applications
Generally lighter than hexagonal rods of an
equivalent size
Available in large x-sectional diameters Flushing Hole
(Diameter Varies
Diameter of rod is based on external dimension With Section)
Hexagon Rods
The cross sectional dimension of material is
measured across the flat
Cross sections are more rigid, heavier & transfer
energy more efficiently
Reduces the annulus in the drill hole for better Flushing Hole
(Diameter Varies
flushing With Section)
12
ROD TYPES
Carburization
OVERVIEW
Round Rod Hexagon Rod
Thread ends
H/F Induction
13
Thread TYPES
OVERVIEW
R Thread (Rope)
Rope threads have a low pitch, 12.7 mm and
a small angle of profile
Sizes: 22 mm 38 mm
Good wear properties
Ideal for single pass or shorthole drilling
such as underground tunneling applications,
that require infrequent uncoupling
HM Thread
HM thread or T thread has a larger pitch
and a larger angle of profile than the Rope
thread
Sizes 38 mm, 45 mm and 51 mm
Excellent wear properties and good coupling
qualities
Ideal for extension drilling with multiple
steel
Greater torque capacity
14
THREAD TYPES
OVERVIEW
EL Thread
Similar angle of profile to the HM thread
Designed for a 60 mm and 70 mm diameter
extension steel for use with the new
generation high powered rockdrills
Excellent wear resistance and a pitch angle
that uncouples easily
Vital component of the LASEROD Straight
Hole Drilling System
15
COUPLING TYPES
OVERVIEW
Bridge Area
Rod End
Rod End
Bridge Area
Semi-Bridge Coupling
Small non-threaded bridge in the center
Steel cannot thread past bridge area
Smaller diameter steel end portions fit
together in the centre bridge area of the
coupling
Semi-bridged couplings are most suited to
high torque machines
Most rope and HM threaded couplings are
semi-bridged
Full-Bridge Coupling
Eliminates the potential for the coupling to
creep along the threaded joints
Typically used in surface applications
Better uncoupling characteristics and tend to
maintain tighter joints
Less chance of jamming
Best suited to machines equipped with
independent rotation (ie., S36IR rockdrill)
Adapter Coupling
Used when changing from one thread type, or
size, to another and are typically required only
in special circumstances
16
Shank Adapters/striking bars
OVERVIEW
Hydraulic and Pneumatic Shanks
Flushing Holes
Striking Face Splines
(Lugs or Flutes)
Female End
Male End
17
18
HANDHELD DRILLING
HANDHELD Rods
Collared and Tapered Rods 20
Rod Shanks 21
Collared Reaming Rods 22
NRT Extension Rods 22
HANDHELD bits
Tapered Bits 23
Reaming Equipment 26
Copyright 2015 Boart Longyear. All rights reserved.
19
HANDHELD DRILLING - RODS
COLLARED AND TAPERED RODS
Collared and Tapered Rods 11 / H22
LENGTH WEIGHT
Part #
mm FT IN KG LB
20
HANDHELD DRILLING - RODS
Collared and Tapered Rods Auger 12 / A22
LENGTH WEIGHT
Part #
mm FT IN KG LB
HANDHELD DRILLING
310007 2440 8' 11.2 24.6
310009 3050 10' 13.8 30.4
310012 3660 12' 14.0 30.8
Rod Shanks
Rod Shanks R25 Thread / 22H
LENGTH WEIGHT
Part #
mm FT IN KG LB
21
HANDHELD DRILLING - RODS
Collared Reaming Rods
Collared Reaming Rods 6.5 / 22H
LENGTH WEIGHT
Part #
mm FT IN KG LB
22
HANDHELD DRILLING - BITS
Tapered Bits
Tapered Button Bits 11
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
50114 32 1 1/4" 3x8 2x7 1F 2G Conical Flat
50118 34 1 11/32" 3x8 2x7 1F 2G Conical Flat
50222 48 1 7/8" 3x9 2x9 1F 2G Conical Flat
HANDHELD DRILLING
50172 34 1 11/32" 4x7 2x7 2F 1G Conical Flat
23
HANDHELD DRILLING - BITS
Tapered Button Bits 12
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
50228 28 1 1/8" 4x7 1x 7 2G Conical Flat
50081 28 1 1/8" 4x7 1x 7 2G Hemispherical Flat
HANDHELD DRILLING
24
HANDHELD DRILLING - BITS
Tapered Blade Bits 12
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
30003 28 1 1/8" 14 X 8 1F 2G G10
30113 30 1 3/16" 15 X 8 1F 2G H9
30115 32 1 1/4" 15 X 8 1F 2G H9
30032 32 1 1/4" 14 X 8 1F 2G G10
30037 38 1 1/2" 14 X 8 1F 2G G10
HANDHELD DRILLING
30039 45 1 3/4" 14 X 8 1F 2G G10
Reaming Equipment
Reaming Equipment 6.5
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
70021 62 2 7/16" 8 x 11 2 x 10 Hemispherical Flat
70022 76 3 8 x 11 2 x 11 Hemispherical Flat
25
26
DRIFTING AND TUNNELING DRILLING
DRIFTING AND TUNNELING DRILLING RODS
R25 Thread Rods 28
R28 Thread Rods Rods 28
R32 Thread Rods Rods 29
R35 Thread Rods Rods 31
27
drifting and tunneling drilling - RODS
R25 Thread Rods
R25 Bit Thread / MM Carburized Rods
LENGTH THREAD WEIGHT
Part #
mm FT IN ROD CROSS BIT END ROD END KG LB
SECTION
28
drifting and tunneling drilling - RODS
R32 Thread Rods
R32 Bit Thread / MM Carburized Rods
LENGTH THREAD WEIGHT
Part #
mm FT IN ROD CROSS BIT END ROD END KG LB
SECTION
D&T drilling
220152 3090 10' 1 10/16" 32H R32 HM38 - -
220400 3700 12' 1 11/16" 32H R32 HM38 23.6 52.0
220095 4310 14' 1 11/16" 32H R32 HM38 26.7 58.9
220157 4915 16' 1 8/16" 32H R32 HM38 30.5 67.2
29
drifting and tunneling drilling - RODS
R32 Bit Thread / MF Carburized Rods
LENGTH THREAD WEIGHT
Part #
mm FT IN ROD CROSS BIT END ROD END KG LB
SECTION
30
drifting and tunneling drilling - RODS
R35 Thread Rods
R35 Bit Thread / MM Carburized Rods
LENGTH THREAD WEIGHT
Part #
mm FT IN ROD CROSS BIT END ROD END KG LB
SECTION
D&T drilling
220477 4300 14' 1 5/16" 39R R35 R38 33.5 73.8
220480 4915 16' 1 8/16" 39R R35 R38 38.6 85.0
220514 6100 20' 3/16" 39R R35 R38 48.9 107.7
31
drifting and tunneling drilling - bits
R23 Thread Bits
R23 Thread Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
110653 33 1 5/16" 5x7 2x7 1F 2G Hemispherical Flat
110477 35 1 3/8" 5x8 2x7 1F 2G Hemispherical Flat
110600 38 1 1/2" 5x8 2x7 1F 2G Hemispherical Flat
Ballistic /
110973 38 1 1/2" 5x9 2x7 1F 2G Flat
Parabolic
32
drifting and tunneling drilling - bits
R25 Thread Blade Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
120208 38 1 1/2" 16 x 9 1F 4G G10
120213 41 1 5/8" 18 x 10 1F 4G G10
120225 45 1 3/4" 21 x 11 1F 4G G10
120258 48 1 7/8" 16 x 9 1F 4G G10
D&T drilling
110904 37 1 15/32" 5x9 2x7 1F 2G Parabolic Flat
110002 38 1 1/2" 5x9 2x7 1F 2G Hemispherical Flat
110611 38 1 1/2" 5x9 2x7 1F 2G Hemispherical Flat
110495 38 1 1/2" 5x9 2x7 1F 2G Parabolic Flat
110167 38 1 1/2" 5x9 2x7 1F 2G Hemispherical Flat
110006 41 1 5/8" 5 x 10 2x8 1F 2G Hemispherical Flat
110576 41 1 5/8" 5 x 10 2x8 1F 2G Parabolic Flat
110118 45 1 3/4" 5 x 10 2x9 1F 2G Hemispherical Flat
110323 48 1 7/8" 5 x 11 2x9 1F 2G Hemispherical Flat
110775 51 2" 5 x 11 2 x 10 1F 2G Hemispherical Flat
110820 51 2" 5 x 11 2 x 10 1F 2G Parabolic Flat
33
drifting and tunneling drilling - bits
R32 Thread Bits
R32 Thread Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
110875 43 1 11/16" 5 x 10 2x9 1F 2G Hemispherical Flat
34
drifting and tunneling drilling - bits
R32 Thread Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
D&T drilling
110903 45 1 3/4" 6 x 10 3x8 3F 1G Hemispherical Flat
110746 45 1 3/4" 6x9 3x8 3F 1G Hemispherical Flat
110648 45 1 3/4" 6x9 3x8 3F 1G Parabolic Flat
110791 45 1 3/4" 6 x 10 3x8 3F 1G Parabolic Flat
35
drifting and tunneling drilling - bits
R32 Thread Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
SIZE SIZE
36
drifting and tunneling drilling - bits
R32 Thread Blade Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
D&T drilling
SIZE SIZE
37
38
PRODUCTION DRILLING
production RODS production Rod Guides
R25 Thread Rods 40 R32 Thread Rod Guides 63
R28 Thread Rods 40 HM38 Thread Rod Guides 63
R32 Thread Rods 41 HM45 Thread Rod Guides 63
R38 Thread Rods 42
HM38 Thread Rods 42 production Guide Tubes
HM45 Thread Rods 44 R32 Thread Guide Tubes 64
HM51 Thread Rods 46 HM38 Thread Guide Tubes 64
BE58 Thread Rods 47 HM45 Thread Guide Tubes 64
EL60 Thread Rods 47 M51 Thread Guide Tubes 65
EL68 Thread Rods 48
production Drill Tubes
Copyright 2015 Boart Longyear. All rights reserved.
39
production drilling - RODS
R25 Thread Rods
R25 Thread / MM Carburized Rods
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
40
production drilling - RODS
R32 Thread Rods
R32 Thread / MM Carburized Rods
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
production drilling
SECTION
41
production drilling - RODS
R38 Thread Rods
R38 Thread / MM Carburized Rods
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
42
production drilling - RODS
HM38 Thread / MM Non-Carburized Rods
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
production drilling
210030 No 1520 5' 39R HM38 13.4 29.5
210031 No 1830 6' 39R HM38 15.8 34.9
210106 Yes 1830 6' 39R HM38 15.9 35.1
210045 No 2440 8' 39R HM38 21.1 46.4
210175 No 2950 9' 8 2/16" 39R HM38 24.9 54.8
210032 No 3050 10' 39R HM38 26.3 58.1
210110 Yes 3050 10' 39R HM38 25.7 56.7
210046 No 3660 12' 39R HM38 31.6 69.6
210112 No 4270 14' 39R HM38 36.1 79.6
43
production drilling - RODS
HM38 Thread / MF Carburized Retrac Rods
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
44
production drilling - RODS
HM45 Thread / MF Carburized Rods
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
production drilling
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
45
production drilling - RODS
HM51 Thread Rods
HM51 Thread / MM Carburized Rods
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
46
production drilling - RODS
BE58 Thread Rods
BE58 Thread / MF Carburized Rods
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
production drilling
EL60 Thread / MF Carburized Rods
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
47
production drilling - RODS
EL68 Thread Rods
EL68 Thread / MM Non-Carburized Rods
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
48
production drilling - bits
HM35 Thread Bits
HM35 Thread Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
110964 54 2 1/8" 6 x 10 3x9 3F 1G Hemispherical Flat
110965 57 2 1/4" 6 x 10 3x9 3F 1G Hemispherical Flat
production drilling
110912 54 2 1/8" 6 x 11 3 x 10 3F 1G Parabolic Flat
110809 64 2 1/2" 6 x 11 3 x 10 3F 1G Parabolic Flat
49
production drilling - bits
HM38 Thread Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
130049 64 2 1/2" 5 x 11 4 x 10 2F Hemispherical Recess
130059 64 2 1/2" 5 x 11 4 x 10 2F Parabolic Recess
50
production drilling - bits
HM38 Thread Straightrac Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
production drilling
HM38 Thread Blade Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
51
production drilling - bits
HM45 Thread Bits
HM45 Thread Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
52
production drilling - bits
HM45 Thread Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
110853 89 3 1/2" 8 x 11 6 x 11 4F 1G Parabolic Recess
production drilling
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
130058 76 3" 6 x 13 3 x 11 / 1 x 10 3F Hemispherical Recess
130105 76 3" 6 x 11 4 x 11 3F Parabolic Recess
53
production drilling - bits
HM45 Thread Retrac Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
130071 89 3 1/2" 9 x 11 6 X 11 3F Parabolic Flat
54
production drilling - bits
HM45 Thread Straightrac Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
Hemispherical
140218 89 3 1/2" 9 x 12 6 x 11 / 2 x 10 3F 2RF Recess
/ Parabolic
production drilling
HM51 Thread Bits
HM51 Thread Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
110663 89 3 1/2" 6 X 12 5 X 12 3F Hemispherical Recess
110662 89 3 1/2" 6 X 12 5 X 12 3F Parabolic Recess
55
production drilling - bits
HM51 Thread Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
110923 140 5 1/2" 8 x 16 7 x 16 4F Hemispherical Recess
56
production drilling - bits
HM51 Thread Retrac Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
130083 115 4 1/2 8 X 14 6 X 14 4F Hemispherical Recess
production drilling
HM51 Thread Straightrac Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
140212 83 3 1/4 8 x 11 6 x 11 4F 1G Parabolic Recess
140095 89 3 1/2 8 x 11 6 x 11 4F 1G Parabolic Recess
57
production drilling - bits
BE58 Thread Bits
BE58 Thread Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
110270 102 4" 8 x 14 7 x 12 2F 2G Hemispherical Flat
58
production drilling - bits
BE58 Thread Straightrac Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
140189 89 3 1/2 8 x 12 4 x 12 / 1 x 11 4F Parabolic Recess
production drilling
110993 102 4" 8 x 14 6 x 12 2F Hemispherical Flat
59
production drilling - bits
EL60 Thread Retrac Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
130114 102 4 8 x 14 5 x 12 2F Hemispherical Recess
Hemispherical
110927 102 4 8 x 14 6 x 12 4F Recess
/ Parabolic
60
production drilling - bits
BE68 Thread Straightrac Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
Hemispherical
140195 102 4 8 x 14 6 x 12 4F Recess
/ Parabolic
production drilling
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
110943 108 4 1/4 8 x 16 6 x 16 2F Parabolic Flat
61
production drilling - bits
EL68 Thread Retrac Button Bits
Diameter BUTTONS
Part # FLUSHING CARBIDE FACE
mm in GAUGE NO/ FRONT NO/ HOLE PROFILE PROFILE
SIZE SIZE
130070 127 5 8 x 14 7 x 14 4F Hemispherical Recess
130134 140 5 1/2 8 x 16 7 x 16 4F Hemispherical Recess
130135 152 6 8 x 16 7 x 16 4F Hemispherical Recess
62
production drilling - Rod Guides
R32 Thread Rod Guides
R32 Thread/ MF Carburized / 54mm Rod Guides
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
production drilling
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
63
production drilling - Rod tubes
R32 Thread Guide Tubes
R32 Thread / MF Carburized Rod Guide Tubes
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
64
production drilling - Rod tubes
HM51 Thread Guide Tubes
HM51 Thread /MF Carburized Rod Guide Tubes
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
production drilling
65
production drilling - drill tubes
R32 Thread Drill Tubes
R32 Thread / MF Carburized Rod Drill Tubes
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
66
production drilling - drill tubes
BE58 Thread Drill Tubes
BE58 Thread / MF Carburized Rod Drill Tubes
LENGTH WEIGHT
WRENCH
Part #
FLATS mm FT IN ROD CROSS THREAD KG LB
SECTION
production drilling
67
68
REAMING TOOLS
REAMER BITS
R32 Thread Reamer Bits 70
R35 Thread Reamer Bits 70
HM38 Reamer Bits 71
HM45 Reamer Bits 71
REAMING EQUIPMENT
6 Degree Reaming Tools 72
12 Degree Reaming Tools 72
Copyright 2015 Boart Longyear. All rights reserved.
69
REAMING TOOLS - REAMER BITS
R32 Thread Reamer Bits
R32 Thread / Hemispherical Buttons Pilot Reamer Bits
Diameter PILOT DIAMETER BUTTONS FLUSHING weight
Part # HOLE
mm in MM IN GAUGE NO/ FRONT NO/ kg lb
SIZE SIZE
6x12 / 4x10
90008 102 4 43 1 11/16 8 x 12 3F 3.4 7.5
/ 2x9
Part # HOLE
mm in MM IN GAUGE NO/ FRONT NO/ kg lb
SIZE SIZE
90031 102 4 9 x 12 11 x 12 3F 1R 3.6 8.0
70
REAMING TOOLS - REAMER BITS
HM38 Reamer Bits
HM38 Thread / Hemispherical Buttons Pilot Reamer Bits
Diameter PILOT DIAMETER BUTTONS FLUSHING weight
Part # HOLE
mm in MM IN GAUGE NO/ FRONT NO/ kg lb
SIZE SIZE
90028 89 3 1/2 48 1 7/8 8 x 10 9 x 10 2F 3.7 8.1
90019 102 4 48 1 7/8 8 x 12 6x12 / 3x10 2F 5.3 11.6
90026 115 4 1/2 48 1 7/8 8 x 12 6x12 / 3x10 2F 5.8 12.7
90021 127 5 48 1 7/8 8 x 14 6x14 / 3x10 2F 5.8 12.9
REAMING TOOLS
71
REAMING TOOLS - REAMING EQUIPMENT
6 degree Reaming Tools
6 Hemispherical Buttons Reaming Bits
Diameter BUTTONS weight
Part #
mm in GAUGE NO/ FRONT NO/ kg lb
SIZE SIZE
70009 76 3 8 x 10 4 x 10 1.3 2.8
70011 89 3 1/2 8 x 10 4 x 10 1.7 3.7
6 Pilot Adapter
PILOT DIAMETER FLUSHING weight
Part # HOLE THREAD
MM IN kg lb
12 Pilot Adapter
PILOT DIAMETER FLUSHING weight
Part # HOLE THREAD
MM IN kg lb
72
SHANK ADAPTERS
SHANK ADAPTERS
Boart Longyear 74
Cannon 75
Atlas Copco 75
Furukawa 78
Garden Deer 80
PW 82
Ingersoll Rand 83
Montabert 83
SCM 84
SVK 85
Copyright 2015 Boart Longyear. All rights reserved.
Tam Rock 85
Toyo 88
UDR 88
73
SHANK ADAPTERS
Boart Longyear
Boart Longyear
LENGTH strike face FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
74
SHANK ADAPTERS
Cannon
Cannon
LENGTH strike face FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
Atlas Copco
Atlas Copco
LENGTH strike face FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
SHANK ADAPTERS
75
SHANK ADAPTERS
Atlas Copco
LENGTH strike fACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
76
SHANK ADAPTERS
Atlas Copco
LENGTH strike FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
77
SHANK ADAPTERS
Atlas Copco
LENGTH strike FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
Furukawa
Furukawa
LENGTH strike FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
78
SHANK ADAPTERS
Furukawa
LENGTH strike fACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
SHANK ADAPTERS
79
SHANK ADAPTERS
gardner denver
Gardner Denver
LENGTH strike FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
80
SHANK ADAPTERS
Gardner Denver
LENGTH strike FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
SHANK ADAPTERS
81
SHANK ADAPTERS
Gardner Denver
LENGTH FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
PW
PW
LENGTH FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
SHANK ADAPTERS
82
SHANK ADAPTERS
Ingersoll Rand
Ingersoll Rand
LENGTH FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
Montabert
Montabert
LENGTH FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
83
SHANK ADAPTERS
Montabert
LENGTH FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
SCM
SCM
LENGTH FACE FRONTHEAD SPLINE
Part # R0CK THREAD
SHANK ADAPTERS
DRILL mm MM MM MM
84
SHANK ADAPTERS
SVK
SVK
LENGTH FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
Tam Rock
Tam Rock
LENGTH FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
SHANK ADAPTERS
85
SHANK ADAPTERS
Tam Rock
LENGTH FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
86
SHANK ADAPTERS
Tam Rock
LENGTH FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
SHANK ADAPTERS
87
SHANK ADAPTERS
Tam Rock
LENGTH FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
Toyo
Toyo
LENGTH FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
UDR
SHANK ADAPTERS
UDR
LENGTH FACE FRONTHEAD SPLINE
Part # R0CK THREAD
DRILL mm MM MM MM
88
ADAPTER AND COUPLINGS
ADAPTER AND COUPLINGS
Semi-Bridge Couplings 90
Full Bridge Couplings 90
Full Bridge Adapter Couplings 90 Copyright 2015 Boart Longyear. All rights reserved.
89
ADAPTER AND COUPLINGS
Semi-Bridge Couplings
Semi-Bridge Couplings
Diameter Length weight
Part # THREAD
mm in MM IN kg lb
90
ACCESSORIES
accessories
Male/ Female Bit Adapters 92
Spiral Male / Female Bit Adapters 92
Male / Female Adapter Guides 92
Split Set Drivers 93
Driver Nuts 93
Spears 94
Bell Taps 94
Knock of Blocks 94
Reaming Shell Adapters 95
Bit Resharpen Gauge 95
Copyright 2015 Boart Longyear. All rights reserved.
91
accessories
Male/ Female Bit Adapters
Male/ Female Bit Adapters
accessories
LENGTH
Part # male thread female thread
MM IN
92
accessories
Split Set Drivers
Split Set Drivers
accessories
WEIGHT
ITEM THREAD
KG LB
NUMBER
Driver Nuts
Driver Nuts
WEIGHT
ITEM THREAD
KG LB
NUMBER
93
accessories
Spears
Spears
accessories
ITEM THREAD
NUMBER
620004 R32
620006 HM38
620007 HM45
620008 HM51
620016 BE58
620015 BE68
Bell Taps
Bell Taps
ITEM THREAD
NUMBER
630010 R25
630004 R32
630006 HM38
630007 HM45
630008 HM51
630013 EL60
knock of blocks
Knock of Blocks
ITEM THREAD
NUMBER
660001 H22
660003 H22RMG
94
accessories
Reaming Shell Adapters
Reaming Shell Adapters
accessories
ITEM THREAD SIZE
NUMBER
380019 TPR 11
690001 TPR 12
3542857
FPO
5600005
FPO
95
96
trouble shooting
Collared and Tapered Rod Failures 98
Collared and Tapered Rod Failures - Socket Ends 99
Blade Bit Failures 100
Button Bit Failures 101
Coupling Failures 104
Shank Adapter Failures 105
Drill Steel Failures 107
Copyright 2015 Boart Longyear. All rights reserved.
97
TROUBLE SHOOTING
COLLARED AND TAPERED ROD FAILURES
6 4
1 5
trouble shooting
1 2
3 7
98
TROUBLE SHOOTING
COLLARED AND TAPERED ROD FAILURES - SOCKET ENDS
trouble shooting
1
2
3
99
TROUBLE SHOOTING
BLADe BIT FAILURES
6
3 2 1
trouble shooting
1
4 7
100
TROUBLE SHOOTING
BUTTON BIT FAILURES
4
9
3
6
2 7
trouble shooting
1
8 5
101
TROUBLE SHOOTING
BUTTON BIT FAILURES
FAILURE PROBABLE CAUSE RECOMMENDED ACTION
POSITION - 4 i) Dry firing i) Do not engage full percussion unless the
Lost gauge button bits are seated firmly against solid material.
Use reduced percussion when collaring
on uneven surfaces if the bits hang up in
the hole and when ratting the drill string to
trouble shooting
loosen connections
ii) Excessive bit body reduction through ii) Ensure the drill cuttings are adequately
erosion from poor flushing or excessive bit bailed. Avoid drilling in broken and
body grinding fractured material where excessive hole
cleaning or back drilling is required.
Remove only the amount of body required
to restore proper button protrusion while
grinding
iii) Scaling with bit iii) Use proper scaling tools
iv) Interference too low when button fitted iv) Forward for analysis
POSITION - 5 i) Overdrilling i) 90% of all button failures are the direct
Shattered buttons result of continuing to drill with excessive
wear flats on the buttons! Remove and
service bits once the wear flat on any button
reaches 1/3 of the face button diameter.
Restore the button profile and protrusion as
recommended in the bit sharpening guide
before continuing use
ii) Drilling into metal ii) Even new buttons will break when
encountering foreign material like stuck
steel, bits, re-bar or any other metals
trapped in the rock
iii) Forceful rotation in undersize holes, in iii) Check that bit diameters are smaller
broken material or through voids in the rock than the hole before attempting to clean
or deepen a hole under these conditions.
Do not force bits if jamming occurs.
Retract until rotation freely then advance
slowly with moderate rotation. If this
fails, use a scrapped bit or grind down
the gauge buttons of the bit to reduce the
diameter sufficiently to pass or remove the
obstruction
iv) Snake skin fatigue from extended drilling iv) Over drilling in soft non-abrasive
in non-abrasive material material leaves a shiny surface on the
buttons. Under magnification, a network of
microscopic cracks can typically be found.
Regularly inspect the bits and re-profile the
buttons to remove these cracks from the
surface of the carbides once the skin on the
carbides starts to show
102
TROUBLE SHOOTING
trouble shooting
is passed or removed. If this fails, use
scrapped bits, a smaller diameter bit or
grind down the gauge buttons of the bit to
reduce the diameter sufficiently to pass or
remove the obstruction
ii) Poor collaring ii) First, ensure mast is secure. Start collar
then full pressure once bit is embedded
300 mm (12.0) in the rock
iii) Excessive button protrusion through iii) Protrusions greater than 3/4 of the
incorrect sharpening button diameter will not provide sufficient
support to resist the tensile forces that the
buttons may encounter
iv) Deformation of the upper portion of the iv) The bit body temperature during drilling
button hole. Possible overheating of the can reach 200 C (392 F) reducing
bits through improper use retention force significantly
POSITION - 7 i) Overdrilling i) 90% of all button failures are the direct
Split button result of continuing to drill with excessive
wear flats on the buttons. Remove and
service bits once the wear flat on any
button reaches 1/3 of the face button
diameter. Restore the button profile and
protrusion as recommended in the bit
sharpening guide before continuing use
POSITION - 8 i) Normal button wear i) Resharpen button and restore to original
Button wear 1/3 profile
diameter
POSITION - 9 i) When drilling in non-abrasive rock, i) Resharpen bits frequently even if no
Snake skin, shiny- microfractures develop in carbide visible wear is evident
polished appearance
103
TROUBLE SHOOTING
COUPLING FAILURES
1
3
2
trouble shooting
104
TROUBLE SHOOTING
SHANK ADAPTER FAILURES
4 5
2 3 6 7 8 9 10
11
12
trouble shooting
13
14
Adapter improperly joined in coupling as a a worn coupling on a new rod. Change out
result of a thread wear couplings with new shank adapters
iv) Excessive rattling iv) Avoid extensive rattling. Boart
Longyear threads are designed for easy
uncoupling. If connectors do not loosen
freely, inspect the threads. Probably
causes of tightly threaded connections are:
(1) dull bits; (2) worn or tight-fitting threads
on steel or couplings; (3) incorrect or
tight-fitting threads; and (4) insufficient or
ineffective thread grease.
POSITION - 10 i) Excessive percussive pressure i) Monitor coupling temperature during
Failure close to bottom drilling; adjust percussive pressures
of thread ii) Broken drill steel ii) Replace drill steel
iii) Worn coupling iii) Replace worn components. Do not put
a worn coupling on a new rod. Change out
your couplings with new rods
POSITION - 11 i) Shank Adapter not properly coupled to i) Replace damaged or worn couplings
Chipped thread end drill steel
ii) Broken drill steel ii) Replace drill steel
iii) Shank Adapter dropped into coupling iii) Inspect feed for misalignment
POSITION - 12 i) Overdrilling bit. Excessive wear flats and i) Resharpen bits when the wear flats
Pitting and galling on insufficient butt protrusion appear 1/3 dull or discard when carbide
threads profile height is compromised. Inspect
bits and select only bits with adequate
protrusion and proper button profile for
most cost effective drilling
ii) Lack of lubrication ii) Grease rockdrill regularly
iii) Inadequate feed force iii) Monitor coupling temperatures and
adjust feed pressure according to
recommendations
POSITION - 13 i) Lack of lubrication i) Grease rockdrill regularly
Pitting and galling on ii) Excessive rotation in soft or broken ii) Adjust drilling pressures
splines ground
POSITION - 14 i) Excessive feed force i) Monitor coupling temperatures and
Excessive wear on top adjust feed pressure according to
of spline shoulder recommendations
ii) Lack of lubrication ii) Grease rockdrill regularly
106
TROUBLE SHOOTING
DRILL STEEL FAILURES
trouble shooting
1
107
TROUBLE SHOOTING
DRILL STEEL FAILURES
1 2
4
3
Trouble shooting
108
care and handling
Bit Wear Overview 110
Bit Wear Patterns 111
Product Servicing - Button Bits 112
Button Reshaping 112
Product Servicing - Blade Bits 113
Inspect the Bit Frequently 113
Gauge Grind Protruding Inserts 113
Blade Bit Sharpening 114
Copyright 2015 Boart Longyear. All rights reserved.
109
AMANDA, THESE PICS ARE
care and handling TOO SMALL FOR PRINT.
110
care and handling
BIT WEAR PATTERNS
Gauge Wear
In some materials such as hard sand stone and quartzite,
the wear tends to be greater on the bit circumference.
Thus, when the buttons are sharpened, the diameter across
the gauge buttons will be less than the diameter of the bit
shoulders and the bit will tend to bind in the hole. Consider
bit replacement.
Over Drilling
The detrimental effects of over drilling bits may not be
immediately apparent. However, running dull bits not only
slows down the drilling rates but escalates drilling costs
by reducing life on the drilling tool components, the rock
drills and the drill rig components. Premature button bit
insert failures are reduced substantially when over drilling is
eliminated and proper sharpening is performed.
111
care and handling
PRODUCT SERVICING - BUTTON BITS
Large wear flats or the presence of snakeskin on the surfaces of buttons can lead to button failure.
Similarly if the protrusion of the buttons above the level of the steel becomes reduced, penetration
rates will drop and wear flats will develop rapidly. Under these conditions it is necessary to redress the
bit to restore it, as near as possible, to its original geometry.
F0 F1 F2 F3 F4
BUTTON RESHAPING
If button protrusion is adequate, satisfactory resharpening can be achieved by use of a performed
diamond faced tool. Sharpening is effected by holding the tool firmly against the button and orbiting
the machine in a circle to achieve a uniform surface finish. Diamond faced tools are designed to cut
carbide and not steel. It is therefore essential that ample protrusion of the button exists before the
diamond tools are used.
112
care and handling (continued)
PRODUCT SERVICING - BLADE BITS
Tungsten carbide blade bits are precision tools, manufactured from high-quality material and
engineered to provide the best results during the most difficult drilling conditions. Tungsten carbide is
resistant to shock and wear, and for maximum results should be properly used and maintained. When
sharpening bits, the idea is to restore them as closely as possible to their original tent shape.
2- 3
Clearance
113
care and handling
BLADe BIT SHARPENING
Silicon carbide grinding wheels are coded according to grit size, hardness, density, and bond variants.
When resharpening blade bits, it is essential that the correct grade of wheel is used. If the wheel is too
hard, overheating of the carbide takes place causing cracking and rapid destruction of the insert. A
soft wheel will wear out rapidly and produce a lot of grinding debris.
care & handling
114
Copyright 2015 Boart Longyear. All rights reserved.
WARRANTY
115
warranty
Limited Warranty. claim must also deliver to Boart Longyear
(a) Consumables. Boart Longyear reasonable evidence of the date of purchase.
warrants for a period of one (1) year after the Boart Longyear shall perform its examination
date of shipment of the consumable products of the goods so returned by Purchaser and
manufactured by it, or the performance of shall report the results of its examination to
related services, under the Contract, that Purchaser within thirty (30) days following
such consumable products are free from its receipt of such goods from Purchaser, or,
defects in materials and workmanship and if longer time is required to complete such
such services are performed in a professional examination, within such time as would be
and workmanlike manner; provided, however, required through the exercise of reasonable
with respect to consumable products diligence. As a further condition to Boart
purchased through an authorized Boart Longyears obligations hereunder for breach of
Longyear distributor, the warranty period shall warranty, Purchaser shall offer its reasonable
commence on the date of purchase by the cooperation and assist Boart Longyear in
end-user. the course of Boart Longyears review of any
(b) Capital Equipment. Boart warranty claim. If requested by Purchaser,
Longyear warrants that the capital equipment Boart Longyear will promptly repair or replace,
manufactured by it is free from defects in at Boart Longyears expense, goods that are
materials and workmanship for a period equal confirmed to be non-conforming as a result of
to the lesser of (i) one (1) year after the date Boart Longyears examination and according to
of shipment, or (ii) the initial 1,000 operating Boart Longyears warranty as set forth herein.
hours. Boart Longyear warrants for a period of All removal and installation of goods shall be
six (6) months after the performance of related at Purchasers expense; provided, however,
services that such services are performed in a Boart Longyear will reimburse the Customer for
professional and workmanlike manner. an amount equal to the reasonable expenses
warranty
(c) General Terms. Boart Longyear incurred by the Customer and attributable to
further warrants that, to the extent applicable, the removal and shipment of any defective
as of the date of shipment or performance, goods. Boart Longyear reserves the right to
all goods manufactured by it and services reimburse Purchaser for an amount equal to
performed shall conform to the written the purchase price of any defective goods
specifications agreed between the parties. in lieu of providing repaired or replacement
THIS IS BOART LONGYEARS ONLY goods. Anything contained herein to the
WARRANTY. BOART LONGYEAR MAKES contrary notwithstanding, in no event shall
NO OTHER WARRANTY, INCLUDING Boart Longyear be liable for breach of warranty
WITHOUT LIMITATION, ANY WARRANTY or otherwise in any manner whatsoever for: (i)
OF MERCHANTABILITY OR FITNESS FOR normal wear and tear; (ii) corrosion, abrasion
A PARTICULAR PURPOSE. As a condition or erosion; (iii) any goods, components, parts,
to Boart Longyears warranty obligations, software or services which, following delivery
Purchaser must: (i) contact Boart Longyear or performance by Boart Longyear, has been
and request authorization to return any subjected to accident, abuse, misapplication,
goods claimed to be defective promptly upon modification, improper repair, alteration,
Purchasers discovery of the alleged defect, improper installation or maintenance, neglect,
(ii) upon receipt of an approved authorization or excessive operating conditions; (iv) defects
code from Boart Longyear, return any goods resulting from Purchasers specifications
claimed to be defective under the foregoing or designs or those of its contractors or
warranty, at Purchasers expense, to the facility subcontractors other than Boart Longyear;
designated by Boart Longyear, and (iii) with (v) defects associated with consumable
respect to consumable products purchased parts or materials, the lifetime of which is
through an authorized Boart Longyear shorter than the warranty period set forth
distributor, the party making the warranty in this Section; (vi) defects associated with
116
warranty
Purchasers specifications or designs or those
of its contractors or subcontractors other than
Boart Longyear; (vii) defects resulting from the
manufacture, distribution, promotion or sale of
Purchasers own products; or (viii) accessories
of any kind used by the Purchaser which are
not manufactured by or approved by Boart
Longyear.
(d) Sourced Goods. If the defective
parts or components are not manufactured
by Boart Longyear, the guarantee of the
manufacturer of those defective parts or
components is accepted by the Purchaser and
is the only guarantee given to the Purchaser in
respect of the defective parts or components.
Boart Longyear agrees to assign to the
Purchaser on request made by the Purchaser
the benefit of any warranty or entitlement to
the defective parts or components that the
manufacturer has granted to Boart Longyear
under any contract or by implication or
operation of law to the extent that the benefit
of any warranty or entitlement is assignable.
(e) Limitation on Liability. Except as
provided for herein, in no event will Boart
warranty
Longyear be liable for any indirect, incidental,
special, consequential, punitive or similar
damages including, but not limited to, lost
profits, loss of data or business interruption
losses. In no event will the total, aggregate
liability of Boart Longyear under the Contract
exceed the value of the Contract under which
liability is claimed. The liability limitations shall
apply even if Boart Longyear has been notified
of the possibility or likelihood of such damages
occurring and regardless of the form of action,
whether in contract, negligence, strict liability,
tort, products liability or otherwise. The parties
agree that these limits of liability shall survive
and continue in full force and effect despite any
termination or expiration of any Contract. Any
action by Purchaser against Boart Longyear
must be commenced within one year after the
cause of action has accrued. No employee
or agent of Boart Longyear is authorized to
make any warranty other than that which is
specifically set forth herein. The provisions in
any specification, brochure or chart issued by
Boart Longyear are descriptive only and are
not warranties.
117
118
Copyright 2015 Boart Longyear. All rights reserved.
PRODUCT INDEX
119
product index
Part #. . . . . . . . . . . . . . Page # Part # . . . . . . . . . . . . . . Page # Part # . . . . . . . . . . . . . . Page # Part # . . . . . . . . . . . . . . Page #
30003. . . . . . . . . . . . . . . . . . . .25 110204. . . . . . . . . . . . . . . . . . . 52 110718. . . . . . . . . . . . . . . . . . . .49 110961 . . . . . . . . . . . . . . . . . . . 36
30032. . . . . . . . . . . . . . . . . . . .25 110216. . . . . . . . . . . . . . . . . . . .52 110719. . . . . . . . . . . . . . . . . . . .49 110962. . . . . . . . . . . . . . . . . . . 32
30037 . . . . . . . . . . . . . . . . . . . .25 110219. . . . . . . . . . . . . . . . . . . .55 110720 . . . . . . . . . . . . . . . . . . . 49 110964. . . . . . . . . . . . . . . . . . . 49
30039 . . . . . . . . . . . . . . . . . . . .25 110236 . . . . . . . . . . . . . . . . . . . 32 110722 . . . . . . . . . . . . . . . . . . . 52 110965. . . . . . . . . . . . . . . . . . . 49
30099. . . . . . . . . . . . . . . . . . . .23 110251. . . . . . . . . . . . . . . . . . . .34 110723 . . . . . . . . . . . . . . . . . . . 52 110969. . . . . . . . . . . . . . . . . . . 61
30110 . . . . . . . . . . . . . . . . . . . . 25 110270 . . . . . . . . . . . . . . . . . . . 58 110724 . . . . . . . . . . . . . . . . . . . 53 110973 . . . . . . . . . . . . . . . . . . . 32
30113 . . . . . . . . . . . . . . . . . . . . 25 110272 . . . . . . . . . . . . . . . . . . . 58 110725 . . . . . . . . . . . . . . . . . . . 53 110980. . . . . . . . . . . . . . . . . . . 37
30115 . . . . . . . . . . . . . . . . . . . . 25 110280 . . . . . . . . . . . . . . . . . . . 60 110726 . . . . . . . . . . . . . . . . . . . 55 110986. . . . . . . . . . . . . . . . . . . 32
50036. . . . . . . . . . . . . . . . . . . .24 110285 . . . . . . . . . . . . . . . . . . . 34 110727 . . . . . . . . . . . . . . . . . . . 58 110988. . . . . . . . . . . . . . . . . . . 34
50066. . . . . . . . . . . . . . . . . . . .24 110288 . . . . . . . . . . . . . . . . . . . 50 110730 . . . . . . . . . . . . . . . . . . . 34 110993. . . . . . . . . . . . . . . . . . . 59
50068. . . . . . . . . . . . . . . . . . . .24 110323 . . . . . . . . . . . . . . . . . . . 33 110737 . . . . . . . . . . . . . . . . . . . 56 110994. . . . . . . . . . . . . . . . . . . 59
50081 . . . . . . . . . . . . . . . . . . . .24 110368. . . . . . . . . . . . . . . . . . . 34 110739 . . . . . . . . . . . . . . . . . . . 37 110996. . . . . . . . . . . . . . . . . . . 35
50096. . . . . . . . . . . . . . . . . . . .24 110375 . . . . . . . . . . . . . . . . . . . 35 110741. . . . . . . . . . . . . . . . . . . .50 110997 . . . . . . . . . . . . . . . . . . . 35
50109 . . . . . . . . . . . . . . . . . . . .24 110384. . . . . . . . . . . . . . . . . . . 49 110746. . . . . . . . . . . . . . . . . . . .35 120045 . . . . . . . . . . . . . . . . . . .37
50111 . . . . . . . . . . . . . . . . . . . . 24 110412. . . . . . . . . . . . . . . . . . . .52 110748. . . . . . . . . . . . . . . . . . . .35 120051. . . . . . . . . . . . . . . . . . . 37
50114 . . . . . . . . . . . . . . . . . . . . 23 110423 . . . . . . . . . . . . . . . . . . . 32 110749. . . . . . . . . . . . . . . . . . . .32 120058 . . . . . . . . . . . . . . . . . . . 51
50118 . . . . . . . . . . . . . . . . . . . . 23 110437 . . . . . . . . . . . . . . . . . . . 56 110754 . . . . . . . . . . . . . . . . . . . 34 120067 . . . . . . . . . . . . . . . . . . . 51
50122. . . . . . . . . . . . . . . . . . . . 23 110438. . . . . . . . . . . . . . . . . . . 55 110765 . . . . . . . . . . . . . . . . . . . 34 120208 . . . . . . . . . . . . . . . . . . .33
50130. . . . . . . . . . . . . . . . . . . . 23 110442. . . . . . . . . . . . . . . . . . . 32 110772 . . . . . . . . . . . . . . . . . . . 34 120213 . . . . . . . . . . . . . . . . . . . 33
50141. . . . . . . . . . . . . . . . . . . . 23 110472 . . . . . . . . . . . . . . . . . . . 34 110775 . . . . . . . . . . . . . . . . . . . 33 120223 . . . . . . . . . . . . . . . . . . .37
50145 . . . . . . . . . . . . . . . . . . . .23 110476 . . . . . . . . . . . . . . . . . . . 32 110777 . . . . . . . . . . . . . . . . . . . 34 120225 . . . . . . . . . . . . . . . . . . .33
50146 . . . . . . . . . . . . . . . . . . . .23 110477 . . . . . . . . . . . . . . . . . . . 32 110778 . . . . . . . . . . . . . . . . . . . 35 120255. . . . . . . . . . . . . . . . . . . 37
50172. . . . . . . . . . . . . . . . . . . . 23 110495 . . . . . . . . . . . . . . . . . . . 33 110790 . . . . . . . . . . . . . . . . . . . 52 120258 . . . . . . . . . . . . . . . . . . .33
50175. . . . . . . . . . . . . . . . . . . . 23 110510. . . . . . . . . . . . . . . . . . . .56 110791. . . . . . . . . . . . . . . . . . . .35 120304 . . . . . . . . . . . . . . . . . . .37
50177. . . . . . . . . . . . . . . . . . . . 24 110511. . . . . . . . . . . . . . . . . . . .56 110793 . . . . . . . . . . . . . . . . . . . 49 120307. . . . . . . . . . . . . . . . . . . 55
50181. . . . . . . . . . . . . . . . . . . . 24 110516. . . . . . . . . . . . . . . . . . . .35 110805. . . . . . . . . . . . . . . . . . . 49 120329 . . . . . . . . . . . . . . . . . . .37
50220. . . . . . . . . . . . . . . . . . . .23 110522 . . . . . . . . . . . . . . . . . . . 37 110809. . . . . . . . . . . . . . . . . . . 49 120348 . . . . . . . . . . . . . . . . . . . 51
50222. . . . . . . . . . . . . . . . . . . .23 110523 . . . . . . . . . . . . . . . . . . . 37 110814. . . . . . . . . . . . . . . . . . . .50 120349. . . . . . . . . . . . . . . . . . . 51
50225 . . . . . . . . . . . . . . . . . . . .24 110526 . . . . . . . . . . . . . . . . . . . 35 110818. . . . . . . . . . . . . . . . . . . .33 130008 . . . . . . . . . . . . . . . . . . .57
50228 . . . . . . . . . . . . . . . . . . . .24 110545. . . . . . . . . . . . . . . . . . . 34 110820 . . . . . . . . . . . . . . . . . . . 33 130012 . . . . . . . . . . . . . . . . . . . 53
50234. . . . . . . . . . . . . . . . . . . .24 110552 . . . . . . . . . . . . . . . . . . . 35 110821 . . . . . . . . . . . . . . . . . . . 32 130048 . . . . . . . . . . . . . . . . . . .35
50242 . . . . . . . . . . . . . . . . . . . .24 110576 . . . . . . . . . . . . . . . . . . . 33 110822 . . . . . . . . . . . . . . . . . . . 32 130049. . . . . . . . . . . . . . . . . . . 50
50254. . . . . . . . . . . . . . . . . . . .24 110577 . . . . . . . . . . . . . . . . . . . 37 110830. . . . . . . . . . . . . . . . . . . 49 130054 . . . . . . . . . . . . . . . . . . .57
70009 . . . . . . . . . . . . . . . . . . . .72 110580 . . . . . . . . . . . . . . . . . . . 32 110833. . . . . . . . . . . . . . . . . . . 52 130055 . . . . . . . . . . . . . . . . . . .57
70011. . . . . . . . . . . . . . . . . . . . 72 110591 . . . . . . . . . . . . . . . . . . . 34 110834. . . . . . . . . . . . . . . . . . . 52 130056 . . . . . . . . . . . . . . . . . . .35
70021. . . . . . . . . . . . . . . . . . . . 25 110597 . . . . . . . . . . . . . . . . . . . 34 110849 . . . . . . . . . . . . . . . . . . . 49 130057. . . . . . . . . . . . . . . . . . . 50
70022 . . . . . . . . . . . . . . . . . . . .25 110599 . . . . . . . . . . . . . . . . . . . 61 110853. . . . . . . . . . . . . . . . . . . 53 130058 . . . . . . . . . . . . . . . . . . .53
70028 . . . . . . . . . . . . . . . . . . . .72 110600. . . . . . . . . . . . . . . . . . . 32 110875 . . . . . . . . . . . . . . . . . . . 34 130059 . . . . . . . . . . . . . . . . . . .50
70030 . . . . . . . . . . . . . . . . . . . .72 110609. . . . . . . . . . . . . . . . . . . 34 110887 . . . . . . . . . . . . . . . . . . . 59 130070. . . . . . . . . . . . . . . . . . . 62
70032 . . . . . . . . . . . . . . . . . . . .72 110611. . . . . . . . . . . . . . . . . . . .33 110888. . . . . . . . . . . . . . . . . . . 59 130071. . . . . . . . . . . . . . . . . . . 54
70034 . . . . . . . . . . . . . . . . . . . .72 110612 . . . . . . . . . . . . . . . . . . . 60 110889. . . . . . . . . . . . . . . . . . . 59 130074 . . . . . . . . . . . . . . . . . . . 50
90008. . . . . . . . . . . . . . . . . . . .70 110615 . . . . . . . . . . . . . . . . . . . 34 110890. . . . . . . . . . . . . . . . . . . 59 130079. . . . . . . . . . . . . . . . . . . 50
product index
product index
200259 . . . . . . . . . . . . . . . . . . . 41 210035. . . . . . . . . . . . . . . . . . . 45 210231. . . . . . . . . . . . . . . . . . . 44 220510. . . . . . . . . . . . . . . . . . . 30
200316. . . . . . . . . . . . . . . . . . . 43 210037. . . . . . . . . . . . . . . . . . . 45 220038 . . . . . . . . . . . . . . . . . . .29 220513. . . . . . . . . . . . . . . . . . . 29
200320 . . . . . . . . . . . . . . . . . . .44 210038. . . . . . . . . . . . . . . . . . . 45 220042 . . . . . . . . . . . . . . . . . . .29 220514. . . . . . . . . . . . . . . . . . . 31
200357 . . . . . . . . . . . . . . . . . . . 41 210040. . . . . . . . . . . . . . . . . . . 46 220068. . . . . . . . . . . . . . . . . . .28 220515. . . . . . . . . . . . . . . . . . . 31
200361 . . . . . . . . . . . . . . . . . . .44 210042. . . . . . . . . . . . . . . . . . . 46 220075 . . . . . . . . . . . . . . . . . . .28 220523 . . . . . . . . . . . . . . . . . . .30
200362 . . . . . . . . . . . . . . . . . . .44 210043 . . . . . . . . . . . . . . . . . . .46 220095. . . . . . . . . . . . . . . . . . .29 220781. . . . . . . . . . . . . . . . . . . 31
200363. . . . . . . . . . . . . . . . . . .46 210044 . . . . . . . . . . . . . . . . . . .43 220096. . . . . . . . . . . . . . . . . . .29 240020 . . . . . . . . . . . . . . . . . . . 21
200364. . . . . . . . . . . . . . . . . . .46 210045. . . . . . . . . . . . . . . . . . . 43 220100. . . . . . . . . . . . . . . . . . . 29 240022 . . . . . . . . . . . . . . . . . . . 21
200365. . . . . . . . . . . . . . . . . . .43 210046. . . . . . . . . . . . . . . . . . . 43 220112 . . . . . . . . . . . . . . . . . . . 29 240035 . . . . . . . . . . . . . . . . . . . 21
200366. . . . . . . . . . . . . . . . . . .43 210048. . . . . . . . . . . . . . . . . . . 45 220115 . . . . . . . . . . . . . . . . . . . 29 240037 . . . . . . . . . . . . . . . . . . . 21
200367 . . . . . . . . . . . . . . . . . . .43 210050. . . . . . . . . . . . . . . . . . . 41 220138. . . . . . . . . . . . . . . . . . . 28 240038 . . . . . . . . . . . . . . . . . . . 21
200372 . . . . . . . . . . . . . . . . . . . 41 210051. . . . . . . . . . . . . . . . . . . 41 220144 . . . . . . . . . . . . . . . . . . .29 240045 . . . . . . . . . . . . . . . . . . . 21
200375 . . . . . . . . . . . . . . . . . . .42 210064 . . . . . . . . . . . . . . . . . . .43 220152. . . . . . . . . . . . . . . . . . . 29 240046 . . . . . . . . . . . . . . . . . . . 21
200376 . . . . . . . . . . . . . . . . . . .40 210068 . . . . . . . . . . . . . . . . . . . 41 220157. . . . . . . . . . . . . . . . . . . 29 240050 . . . . . . . . . . . . . . . . . . . 21
200377 . . . . . . . . . . . . . . . . . . .42 210072. . . . . . . . . . . . . . . . . . . 44 220159. . . . . . . . . . . . . . . . . . . 29 240095 . . . . . . . . . . . . . . . . . . . 21
200378 . . . . . . . . . . . . . . . . . . .40 210073. . . . . . . . . . . . . . . . . . . 41 220161. . . . . . . . . . . . . . . . . . . 29 240096 . . . . . . . . . . . . . . . . . . . 21
200379 . . . . . . . . . . . . . . . . . . .44 210080. . . . . . . . . . . . . . . . . . . 45 220164. . . . . . . . . . . . . . . . . . . 29 240137. . . . . . . . . . . . . . . . . . . 21
200383. . . . . . . . . . . . . . . . . . .42 210082. . . . . . . . . . . . . . . . . . . 45 220166. . . . . . . . . . . . . . . . . . . 29 240145. . . . . . . . . . . . . . . . . . . 21
200386. . . . . . . . . . . . . . . . . . .44 210083 . . . . . . . . . . . . . . . . . . .46 220170. . . . . . . . . . . . . . . . . . . 29 240160. . . . . . . . . . . . . . . . . . . 21
200397 . . . . . . . . . . . . . . . . . . .44 210089. . . . . . . . . . . . . . . . . . . 47 220179. . . . . . . . . . . . . . . . . . . 28 240164. . . . . . . . . . . . . . . . . . . 21
200398 . . . . . . . . . . . . . . . . . . .46 210091. . . . . . . . . . . . . . . . . . . 45 220194. . . . . . . . . . . . . . . . . . . 28 250063. . . . . . . . . . . . . . . . . . .20
200401 . . . . . . . . . . . . . . . . . . . 41 210106 . . . . . . . . . . . . . . . . . . . 43 220198. . . . . . . . . . . . . . . . . . . 28 250118 . . . . . . . . . . . . . . . . . . . 20
200404. . . . . . . . . . . . . . . . . . .46 210107 . . . . . . . . . . . . . . . . . . . 41 220209. . . . . . . . . . . . . . . . . . .29 250119 . . . . . . . . . . . . . . . . . . . 20
200411. . . . . . . . . . . . . . . . . . . 42 210108 . . . . . . . . . . . . . . . . . . . 45 220219. . . . . . . . . . . . . . . . . . . 28 250120. . . . . . . . . . . . . . . . . . . 20
200416. . . . . . . . . . . . . . . . . . . 42 210110. . . . . . . . . . . . . . . . . . . .43 220229. . . . . . . . . . . . . . . . . . .28 250121. . . . . . . . . . . . . . . . . . . 20
200417. . . . . . . . . . . . . . . . . . . 43 210112. . . . . . . . . . . . . . . . . . . .43 220242 . . . . . . . . . . . . . . . . . . .28 250122. . . . . . . . . . . . . . . . . . . 20
200418. . . . . . . . . . . . . . . . . . . 44 210115. . . . . . . . . . . . . . . . . . . . 41 220262 . . . . . . . . . . . . . . . . . . .28 250123. . . . . . . . . . . . . . . . . . . 20
121
product index
Part # . . . . . . . . . . . . . . Page # Part # . . . . . . . . . . . . . . Page # Part # . . . . . . . . . . . . . . Page # Part # . . . . . . . . . . . . . . Page #
250160. . . . . . . . . . . . . . . . . . . 20 310003. . . . . . . . . . . . . . . . . . . 21 450380 . . . . . . . . . . . . . . . . . . .86 450823 . . . . . . . . . . . . . . . . . . .79
250161. . . . . . . . . . . . . . . . . . . 20 310005. . . . . . . . . . . . . . . . . . . 21 450405 . . . . . . . . . . . . . . . . . . .85 450824 . . . . . . . . . . . . . . . . . . .80
250162. . . . . . . . . . . . . . . . . . . 20 310007. . . . . . . . . . . . . . . . . . . 21 450407 . . . . . . . . . . . . . . . . . . .85 450825 . . . . . . . . . . . . . . . . . . .80
250163. . . . . . . . . . . . . . . . . . . 20 310009. . . . . . . . . . . . . . . . . . . 21 450408 . . . . . . . . . . . . . . . . . . .85 450826 . . . . . . . . . . . . . . . . . . .75
250183. . . . . . . . . . . . . . . . . . . 20 310012 . . . . . . . . . . . . . . . . . . . 21 450412. . . . . . . . . . . . . . . . . . . 87 450827 . . . . . . . . . . . . . . . . . . .88
250185. . . . . . . . . . . . . . . . . . . 20 350010. . . . . . . . . . . . . . . . . . . 90 450423 . . . . . . . . . . . . . . . . . . .76 450839 . . . . . . . . . . . . . . . . . . .82
250187. . . . . . . . . . . . . . . . . . . 20 350012. . . . . . . . . . . . . . . . . . . 90 450438. . . . . . . . . . . . . . . . . . .83 450840 . . . . . . . . . . . . . . . . . . .87
250188. . . . . . . . . . . . . . . . . . . 20 350034 . . . . . . . . . . . . . . . . . . .90 450442 . . . . . . . . . . . . . . . . . . .78 450841. . . . . . . . . . . . . . . . . . . 87
250189. . . . . . . . . . . . . . . . . . . 20 350045. . . . . . . . . . . . . . . . . . .90 450443. . . . . . . . . . . . . . . . . . .78 450842 . . . . . . . . . . . . . . . . . . .79
250190. . . . . . . . . . . . . . . . . . . 20 350051. . . . . . . . . . . . . . . . . . . 90 450445. . . . . . . . . . . . . . . . . . .86 450846. . . . . . . . . . . . . . . . . . .87
250191. . . . . . . . . . . . . . . . . . . 20 350052 . . . . . . . . . . . . . . . . . . .90 450454. . . . . . . . . . . . . . . . . . .75 450851. . . . . . . . . . . . . . . . . . . 88
250195. . . . . . . . . . . . . . . . . . . 20 350057 . . . . . . . . . . . . . . . . . . .90 450455 . . . . . . . . . . . . . . . . . . .83 450852 . . . . . . . . . . . . . . . . . . .88
250196. . . . . . . . . . . . . . . . . . . 20 360008. . . . . . . . . . . . . . . . . . .90 450459 . . . . . . . . . . . . . . . . . . .78 450853 . . . . . . . . . . . . . . . . . . .75
250198. . . . . . . . . . . . . . . . . . . 20 360014 . . . . . . . . . . . . . . . . . . .90 450460. . . . . . . . . . . . . . . . . . .83 450855 . . . . . . . . . . . . . . . . . . .75
250200 . . . . . . . . . . . . . . . . . . .20 360017. . . . . . . . . . . . . . . . . . . 90 450466. . . . . . . . . . . . . . . . . . .86 450856 . . . . . . . . . . . . . . . . . . .77
250201. . . . . . . . . . . . . . . . . . . 20 360018. . . . . . . . . . . . . . . . . . . 90 450468. . . . . . . . . . . . . . . . . . .83 450857 . . . . . . . . . . . . . . . . . . .77
250362 . . . . . . . . . . . . . . . . . . .20 360029. . . . . . . . . . . . . . . . . . .90 450469 . . . . . . . . . . . . . . . . . . .77 450858 . . . . . . . . . . . . . . . . . . .75
250364 . . . . . . . . . . . . . . . . . . .20 360030. . . . . . . . . . . . . . . . . . .90 450475 . . . . . . . . . . . . . . . . . . .85 450861 . . . . . . . . . . . . . . . . . . .80
250365 . . . . . . . . . . . . . . . . . . .20 360031 . . . . . . . . . . . . . . . . . . .90 450477 . . . . . . . . . . . . . . . . . . .79 450862 . . . . . . . . . . . . . . . . . . .84
250374. . . . . . . . . . . . . . . . . . . 20 360035. . . . . . . . . . . . . . . . . . .90 450485. . . . . . . . . . . . . . . . . . .84 450863. . . . . . . . . . . . . . . . . . .75
250387 . . . . . . . . . . . . . . . . . . .20 360039 . . . . . . . . . . . . . . . . . . .90 450487 . . . . . . . . . . . . . . . . . . .79 450868. . . . . . . . . . . . . . . . . . .86
250440 . . . . . . . . . . . . . . . . . . .20 360045. . . . . . . . . . . . . . . . . . .90 450500 . . . . . . . . . . . . . . . . . . . 74 450870 . . . . . . . . . . . . . . . . . . .86
250441. . . . . . . . . . . . . . . . . . . 20 370008 . . . . . . . . . . . . . . . . . . .92 450524 . . . . . . . . . . . . . . . . . . .77 450871. . . . . . . . . . . . . . . . . . . 86
250447 . . . . . . . . . . . . . . . . . . .20 370009 . . . . . . . . . . . . . . . . . . .92 450525 . . . . . . . . . . . . . . . . . . .79 450872 . . . . . . . . . . . . . . . . . . .85
250448 . . . . . . . . . . . . . . . . . . .20 370014. . . . . . . . . . . . . . . . . . . 92 450539 . . . . . . . . . . . . . . . . . . .77 450873 . . . . . . . . . . . . . . . . . . .87
250473 . . . . . . . . . . . . . . . . . . .20 370015 . . . . . . . . . . . . . . . . . . . 92 450548. . . . . . . . . . . . . . . . . . .78 450879 . . . . . . . . . . . . . . . . . . .85
250516. . . . . . . . . . . . . . . . . . . 20 370022 . . . . . . . . . . . . . . . . . . .92 450550 . . . . . . . . . . . . . . . . . . .77 450889 . . . . . . . . . . . . . . . . . . .75
250517. . . . . . . . . . . . . . . . . . . 20 370031. . . . . . . . . . . . . . . . . . . 92 450551. . . . . . . . . . . . . . . . . . . 78 450890 . . . . . . . . . . . . . . . . . . . 81
250699 . . . . . . . . . . . . . . . . . . .20 370035 . . . . . . . . . . . . . . . . . . .92 450565 . . . . . . . . . . . . . . . . . . . 74 450891 . . . . . . . . . . . . . . . . . . . 81
250727. . . . . . . . . . . . . . . . . . . 20 370037. . . . . . . . . . . . . . . . . . . 92 450575 . . . . . . . . . . . . . . . . . . .86 450895 . . . . . . . . . . . . . . . . . . . 81
260001 . . . . . . . . . . . . . . . . . . .22 370038 . . . . . . . . . . . . . . . . . . .92 450576 . . . . . . . . . . . . . . . . . . .79 450896 . . . . . . . . . . . . . . . . . . .82
260002. . . . . . . . . . . . . . . . . . .22 370045 . . . . . . . . . . . . . . . . . . .92 450582 . . . . . . . . . . . . . . . . . . .80 450899 . . . . . . . . . . . . . . . . . . .82
260003. . . . . . . . . . . . . . . . . . .22 370047. . . . . . . . . . . . . . . . . . . 92 450586 . . . . . . . . . . . . . . . . . . .84 450902. . . . . . . . . . . . . . . . . . .82
260004. . . . . . . . . . . . . . . . . . .22 370049. . . . . . . . . . . . . . . . . . . 92 450591. . . . . . . . . . . . . . . . . . . 87 560001 . . . . . . . . . . . . . . . . . . .93
260015. . . . . . . . . . . . . . . . . . . 22 370050 . . . . . . . . . . . . . . . . . . .92 450594 . . . . . . . . . . . . . . . . . . .86 560014 . . . . . . . . . . . . . . . . . . .93
260016. . . . . . . . . . . . . . . . . . . 22 370051. . . . . . . . . . . . . . . . . . . 92 450603. . . . . . . . . . . . . . . . . . .86 560015. . . . . . . . . . . . . . . . . . . 93
260021 . . . . . . . . . . . . . . . . . . .22 370052 . . . . . . . . . . . . . . . . . . .92 450605. . . . . . . . . . . . . . . . . . .77 560016. . . . . . . . . . . . . . . . . . . 93
270004 . . . . . . . . . . . . . . . . . . .67 380003. . . . . . . . . . . . . . . . . . .72 450607 . . . . . . . . . . . . . . . . . . .77 560017. . . . . . . . . . . . . . . . . . . 93
270012. . . . . . . . . . . . . . . . . . . 64 380004. . . . . . . . . . . . . . . . . . .72 450612. . . . . . . . . . . . . . . . . . . 84 560019. . . . . . . . . . . . . . . . . . . 93
270013. . . . . . . . . . . . . . . . . . . 64 380015. . . . . . . . . . . . . . . . . . . 72 450613. . . . . . . . . . . . . . . . . . . 84 560021 . . . . . . . . . . . . . . . . . . .93
270018. . . . . . . . . . . . . . . . . . . 65 380017. . . . . . . . . . . . . . . . . . . 72 450614 . . . . . . . . . . . . . . . . . . .77 560023 . . . . . . . . . . . . . . . . . . .93
270019. . . . . . . . . . . . . . . . . . . 65 380019. . . . . . . . . . . . . . . . . . . 95 450629. . . . . . . . . . . . . . . . . . .80 560026. . . . . . . . . . . . . . . . . . .93
product index
product index
123
124
contact information
Canada
Boart Longyear
2442 South Sheridan Way
Mississauga, Ontario
Canada L5J 2M7
info@boartlongyear.com
contact info
125
BACK COVER
TO BE PICKED UP BY
ASPEN PRESS