Académique Documents
Professionnel Documents
Culture Documents
Functions
Main switch The temperature function Safety features
The heater is fitted with a main circuit The SKF TIH 090m is equipped with The induction heater is equipped with the
breaker, which provides automatic temperature heating cycle mode, which following safety features:
overload protection. The main switch is is pre-set at 110 C (230 F) to prevent -main switch with over current circuit
supposed to be used when the heater is bearing over-heating, as well as time breaker
switched off for a longer period. heating mode. -automatic current control
-automatic overheating protection
-a probe control function, checking that
Start/stop The time function
an increase of 1 is encountered every 15
The START/STOP key is pressed to start By using the TIME mode, the heating
seconds
and stop the heating cycle with cycle will be monitored by time. The
-temperature mode pre-set at 110 C
automatic demagnetisation. remaining heating time will be displayed
(230 F), preventing bearing over-
during operation.
heating
Input voltage self adjustment
Thermometer mode
The TIH 090m has a standard execution
The heater has a special thermometer Error guiding codes
ranging from 400V/50Hz to 460V/60Hz.
function allowing temperature In case of disturbances in the operation
Once connected to the power source,
measurement while not heating. of the heaters, an error code will appear
the TIH 090m detects the power supply
on the display to inform what is wrong
and adjusts its voltage accordingly.
and how to solve the problem.
Demagnetisation
The work piece is always automatically
Power reduction function
demagnetised at the end of each Maintenance
In both the TEMP mode and the TIME
heating cycle. This most essential For ultimate performance and lifetime:
mode the power level can be adjusted in
function is only eliminated if the heater -Protect the yoke supports and the yokes
steps of 20% for slower heating of
is switched off by the main switch or by against corrosion, damage and
sensitive or small work pieces.
pulling the plug. When using the heater deformation. A perfect contact between
only for demagnetising, just run the the yoke and the yoke support is vital
heater on shortest possible heating for optimal performance
time. -Protect the heater from water and high
humidity
Technical data
Designation TIH 090M
Small to medium size induction heater equipped with a cooling fan
Description
for continuous use
Colour Light grey
Maximum power consumption 6,4 kVA
p p ,
Replacement parts
Designation Description
TIH 090-P Power print 400-460 V, 50-60 Hz
TIH 090-S Main switch
TIH 090-C Coil 400-460 V
TIH 070/090-H Heating pad and sealing
TIH 070/090-SA Swivel arm
Yoke 55 x 55 x 275 mm (2.2 x 2.2 x 10.8 in) for heating bearings with bore diameter of 80 mm (3.1 in)
TIH 070/090-Y8
and larger
Yoke 40 x 40 x 275 mm (1.6 x 1.6 x 10.8 in) for heating bearings with bore diameter of 60 mm (2.4 in)
TIH 070/090-Y6
and larger
Yoke 28 x 28 x 275 mm (1.1 x 1.1 x 10.8 in) for heating bearings with bore diameter of 40 mm (1.6 in)
TIH 070/090-Y4
and larger
Yoke 20 x 20 x 275 mm (0.8 x 0.8 x 10.8 in) for heating bearings with bore diameter of 30 mm (1.2 in)
TIH 070/090-Y3
and larger
Yoke 14 x 14 x 275 mm (0.5 x 0.5 x 10.8 in), for heating bearings with bore diameter of 20 mm (0.8 in)
TIH 070/090-Y2
and larger.
TIH 070/090-YS Support yoke set 55 x 55 x 100 (2x) (2.2 x 2.2 x 3.9 in)
TIH070/090-CP Control print for TIH 090m/400-460V
TIH P2 Temperature probe, K type