Académique Documents
Professionnel Documents
Culture Documents
TLP250
Transistor Inverter
Inverter For Air Conditionor
Unit in mm
IGBT Gate Drive
Power MOS FET Gate Drive
GND
1 : N.C.
5
A 0.1F bypass capcitor must be 2 : Anode
connected between pin 8 and 5 (See Note 5). 3 : Cathode
4 : N.C.
5 : GND
6 : VO (Output)
7 : VO
8 : VCC
Truth Table
Tr1 Tr2
Input On On Off
LED Off Off On
1 2004-06-25
TLP250
Absolute Maximum Ratings (Ta = 25C)
Forward current IF 20 mA
Reverse voltage VR 5 V
(Ta 70C) 35
Supply voltage VCC V
(Ta = 85C) 24
Output voltage derating (Ta 70C) VO / Ta 0.73 V / C
Supply voltage derating (Ta 70C) VCC / Ta 0.73 V / C
Junction temperature Tj 125 C
Operating frequency (Note 3) f 25 kHz
Operating temperature range Topr 20~85 C
Storage temperature range Tstg 55~125 C
Lead soldering temperature (10 s) (Note 4) Tsol 260 C
Isolation voltage (AC, 1 min., R.H. 60%) (Note 5) BVS 2500 Vrms
Note 6: A ceramic capacitor(0.1F) should be connected from pin 8 to pin 5 to stabilize the operation of the high
gain linear amplifier. Failure to provide the bypassing may impair the switching proparty. The total lead
length between capacitor and coupler should not exceed 1cm.
2 2004-06-25
TLP250
Electrical Characteristics (Ta = 20~70C, unless otherwise specified)
Test
Characteristic Symbol Cir Test Condition Min. Typ.* Max. Unit
cuit
Input forward voltage VF IF = 10 mA , Ta = 25C 1.6 1.8 V
Temperature coefficient of
VF / Ta IF = 10 mA 2.0 mV / C
forward voltage
Input reverse current IR VR = 5V, Ta = 25C 10 A
Input capacitance CT V = 0 , f = 1MHz , Ta = 25C 45 250 pF
IF = 10 mA
H level IOPH 3 0.5 1.5
VCC = 30V V86 = 4V
Output current A
(*1) IF = 0
L level IOPL 2 0.5 2
V65 = 2.5V
VCC1 = +15V, VEE1 = 15V
H level VOH 4 11 12.8
RL = 200, IF = 5mA
Output voltage V
VCC1 = +15V, VEE1 = 15V
L level VOL 5 14.2 12.5
RL = 200, VF = 0.8V
VCC = 30V, IF = 10mA
7
H level ICCH Ta = 25C
VCC = 30V, IF = 10mA 11
Supply current mA
VCC = 30V, IF = 0mA
7.5
L level ICCL Ta = 25C
VCC = 30V, IF = 0mA 11
Threshold input Output IFLH VCC1 = +15V, VEE1 = 15V
1.2 5 mA
current LH RL = 200, VO > 0V
Threshold input Output IFHL VCC1 = +15V, VEE1 = 15V
0.8 V
voltage HL RL = 200, VO < 0V
Supply voltage VCC 10 35 V
Capacitance CS VS = 0 , f = 1MHz
1.0 2.0 pF
(inputoutput) Ta = 25
VS = 500V , Ta = 25C 12 14
Resistance(inputoutput) RS 110 10
R.H. 60%
3 2004-06-25
TLP250
Switching Characteristics (Ta = 20~70C , unless otherwise specified)
Test
Characteristic Symbol Cir Test Condition Min. Typ.* Max. Unit
cuit
Propagation LH tpLH 0.15 0.5
delay time IF = 8mA (Note 7)
HL tpHL 0.15 0.5
6 VCC1 = +15V, VEE1 = 15V s
Output rise time tr RL = 200
Output fall time tf
Common mode transient
VCM = 600V, IF = 8mA
immunity at high level CMH 7 5000 V / s
VCC = 30V, Ta = 25C
output
Common mode transient
VCM = 600V, IF = 0mA
immunity at low level CML 7 5000 V / s
VCC = 30V, Ta = 25C
output
4 2004-06-25
TLP250
8
1 8 1
0.1F
VCC
A
IOPL
4 5 4 V6-5
8 8
1 1
VCC VCC1
0.1F 0.1F
IF V8-6 IF
RL
A
V VOH
IOPH
4 4
VEE1
8
1
VCC1
0.1F
VF
RL
V VOL
4
VEE1
5 2004-06-25
TLP250
Test Circuit 6: tpLH, tpHL, tr tf
8
IF tr
tf
IF 0.1F VCC1
VO VOH 80%
RL VO GND
VOL 80%
tpLH tpHL
100
VEE1
8
1
SW IF 0.1F
VCC
A B
VO
VCM
+ -
600V
90%
VCM
10% tf
tr
CML = 480 (V)
SW :A(IF=8mA) tr (s)
CMH CMH = 480 (V)
VO 26V tf (s)
3V
CHL
SW :B(IF=0)
CML(CMH) is the maximum rate of rise (fall) of the common mode voltage that can be sustained with the output
voltage in the low (high) state.
6 2004-06-25
TLP250
IF VF VF / Ta IF
100 -2.6
Ta = 25 C
50
30
coefficient VF / Ta (mV / C)
-2.4
10
5 -2.2
Forward current IF
1 -2.0
0.5
0.3
-1.8
0.1
0.05 -1.6
0.03
0.01 -1.4
1.0 1.2 1.4 1.6 1.8 2.0 0.1 0.3 0.5 1 3 5 10 30
IF Ta VCC Ta
40 40
(V)
Allowable forward current
30 30
Allowable supply voltage VCC
IF (mA)
20 20
10 10
0 0
0 20 40 60 80 100 0 20 40 60 80 100
IOPH, IOPL Ta
PW 2.5 s, f 15 KHz
2
Allowable peak output current
IOPH, IOPL (A)
0
0 20 40 60 80 100
7 2004-06-25
TLP250
The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed
by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is
granted by implication or otherwise under any patent or patent rights of TOSHIBA or others.
TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in
general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility
of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire
system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life,
bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the
most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the
Handling Guide for Semiconductor Devices, or TOSHIBA Semiconductor Reliability Handbook etc..
The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal
equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products
are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a
malfunction or failure of which may cause loss of human life or bodily injury (Unintended Usage). Unintended Usage include
atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments,
combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products
listed in this document shall be made at the customers own risk.
The products described in this document are subject to the foreign exchange and foreign trade laws.
TOSHIBA products should not be embedded to the downstream products which are prohibited to be produced and sold, under
any law and regulations.
GaAs(Gallium Arsenide) is used in this product. The dust or vapor is harmful to the human body. Do not break, cut, crush or
dissolve chemically.
8 2004-06-25