Académique Documents
Professionnel Documents
Culture Documents
In this practice skills assessment, you will configure the Famous University network with OSPF
routing. The network is configured with both IPv4 and IPv6 on all devices. This will allow you to
implement routing in both OSPFv2 and OSPFv3. In addition, you will configure both versions
of OSPF in multiple areas. For a full list of tasks, see below.
CCNA 6 | CCNAv6 - Free CCNA Exam Answers 2017 - Study CCNA for free! Page 1 of 8
ScaN Practice Skills Exam OSPF - PT
All IOS device configurations should be completed from a direct terminal connection to
the device console.
Router Science:
Router Bio:
CCNA 6 | CCNAv6 - Free CCNA Exam Answers 2017 - Study CCNA for free! Page 2 of 8
ScaN Practice Skills Exam OSPF - PT
Router Physics
Router Technology:
Router CompSci:
Router Electronics:
Addressing Table
Use the following addresses to configure the network. Some addresses are
preconfigured on devices that you are not required to configure, and are provided
for reference purposes only.
Device Interface Addresses
CCNA 6 | CCNAv6 - Free CCNA Exam Answers 2017 - Study CCNA for free! Page 3 of 8
ScaN Practice Skills Exam OSPF - PT
10.10.10.2/30
S0/0/0 2001:DB8:10::2/64
FE80::1 link local
10.10.20.2/30
Administration S0/0/1 2001:DB8:20::2/64
FE80::1 link local
10.0.0.1/30
S0/1/0 2001:DB8:1::1/64
FE80::1 link local
172.16.10.1/30
S0/0/1 2001:DB8:10A::1/64
FE80::10 link local
10.10.10.1/30
Science S0/0/0 2001:DB8:10::1/64
FE80::10 link local
172.16.10.5/30
S0/1/0 2001:DB8:10B::1/64
FE80::10 link local
192.168.11.1/24
G0/0 2001:DB8:11::1/64
FE80::101 link local
172.16.10.2/30
Bio S0/0/0 2001:DB8:10A::2/64
FE80::101 link local
172.16.10.9/30
G0/1 2001:DB8:10C::1/64
FE80::101 link local
192.168.12.1/24
Physics G0/0 2001:DB8:12::1/64
FE80::102 link local
CCNA 6 | CCNAv6 - Free CCNA Exam Answers 2017 - Study CCNA for free! Page 4 of 8
ScaN Practice Skills Exam OSPF - PT
172.16.10.6/30
S0/0/0 2001:DB8:10B::2/64
FE80::102 link local
172.16.10.10/30
G0/1 2001:DB8:10C::2/64
FE80::102 link local
172.16.20.1/30
S0/0/1 2001:DB8:2A::1/64
FE80::20 link local
10.10.20.1/30
Technology S0/0/0 2001:DB8:20::1/64
FE80::20 link local
172.16.20.5/30
S0/1/0 2001:DB8:2B::1/64
FE80::20 link local
192.168.21.1/24
G0/0 2001:DB8:21::1/63
FE80::201 link local
CompSci
172.16.20.2/30
S0/0/0 2001:DB8:20A::2/63
FE80::201 link local
192.168.22.1/24
G0/0 2001:db8:22::1/64
FE80::202 link local
Electronics
172.16.20.6/30
S0/0/0 2001:DB8:20B::2/64
FE80::202 link local
CCNA 6 | CCNAv6 - Free CCNA Exam Answers 2017 - Study CCNA for free! Page 5 of 8
ScaN Practice Skills Exam OSPF - PT
The addresses of the PC and server hosts are provided for connectivity testing purposes. All
addressing is preconfigured.
Instructions
Step1: Configure default static routes on the Administration router.
Configure IPv4 and IPv6 default static routes on Administration. Use the exit interface value
in your configuration.
CCNA 6 | CCNAv6 - Free CCNA Exam Answers 2017 - Study CCNA for free! Page 6 of 8
ScaN Practice Skills Exam OSPF - PT
1. For the multiaccess network connected between the Bio and Physics routers,
configure priorities so that Bio will become the DR and Physics will be the BDR. Use
priority values of 255 and 200.
2. Configure the interfaces on all routers that are attached to LANs with hosts to not send
OSPFv2 traffic into the LAN.
CCNA 6 | CCNAv6 - Free CCNA Exam Answers 2017 - Study CCNA for free! Page 7 of 8
ScaN Practice Skills Exam OSPF - PT
3. Enable all routers to automatically and accurately calculate costs for routes that include
1Gbps Ethernet networks by changing the reference bandwidth.
4. Configure OSPFv2 so that the default routes that are configured on Administration are
automatically distributed to all routers in the network.
5. Adjust the OSPFv2 timers on the Ethernet link between Bio and Physics as follows:
Hello: 5 seconds
Dead: 20 seconds
1. For the multiaccess network connected between the Bio and Physics routers configure
priorities so that Bio will become the DR and Physics will be the BDR. Use priority
values of 255 and 200.
2. Configure the interfaces on all routers that are attached to LANs with hosts to not send
OSPFv3 traffic into the LAN.
3. Enable all routers to automatically and accurately calculate costs for routes that include
1Gbps Ethernet networks by changing the reference bandwidth.
4. Configure OSPFv3 so that the default routes that are configured on Administration are
automatically distributed to all routers in the network.
5. Explicitly configure the OSPFv3 timers on the Ethernet link
between Bio and Physics as follows:
Hello: 5 seconds
Dead: 20 seconds
CCNA 6 | CCNAv6 - Free CCNA Exam Answers 2017 - Study CCNA for free! Page 8 of 8