Vous êtes sur la page 1sur 6

Parameter name

Power Type

Power Level

Cell Extension Type


Cell IUO Type
Enhanced Concentric Allowed
Concentric Circles HO Allowed
UL to OL HO Allowed
OL to UL HO Allowed
RX_LEV for UO HO Allowed
RX_QUAL for UO HO Allowed
TA for UO HO Allowed
RX_LEV Threshold
RX_LEV Hysteresis
RX_QUAL Threshold
TA Threshold
TA Hysteresis
Assign Optimum Layer
Assign-optimum-level Threshold
TA Threshold of Assignment Pref
TA Pref. of Imme-Assign Allowed
TA Threshold of Imme-Assign Pref
Pref. Subcell in HO of Intra-BSC
Incoming-to-BSC HO Optimum Layer
OtoU HO Received Level Threshold
UtoO HO Received Level Threshold
UtoO Traffic HO Allowed
MaxRetry Time after UtoO Fail
En Iuo Out Cell Low Load Thred
En Iuo Out Cell General OverLoad Thred
En Iuo Out Cell Serious OverLoad Thred
Feature decription existing value

20w for S4/4/4


one way to control the overlaid subcell radius

This parameter specifies the transmit power level of the TRX. The greater this
parameter is, the smaller the transmit power is.
When this parameter is set to 0, the transmit power level of the TRX is the greatest.
Each time this parameter increases by one level, the transmit power reduces by 2 0
dB.
For different types of BTSs, the value range of this parameter is different.
DBS3900,BTS3900 : 0-10
This can allow the TA exceeds 63. Double Timeslot Extensi
The absolutely necessary depency for extension type cell Concentric Cell
on
This parameter specifies whether the concentric cell handover is enabled. The concenno
This parameter specifies whether the handover from the UL subcell to the OL subcell yes
This parameter specifies whether the handover from the OL subcell to the UL subcell yes
This parameter specifies whether the downlink receive level is used as a decisive cond no
This parameter specifies whether the downlink receive quality is used as a decisive cono
This parameter specifies whether the TA is used as a decisive condition for the concenno
The level values 0 through 63 map to -110 dBm to -47 dBm. 0
When the Enhanced Concentric Allowed parameter is set to No, the coverage of the OL 0 subcell and UL subcell is determin
If the Enhanced Concentric Allowed parameter is set to No, the coverage of the OL subcell
70 and UL subcell is determined b
TA threshold must be smaller than TA emergency handover threshold. 63
If the Enhanced Concentric Allowed parameter is set to Yes, the coverage of the OL subcell
3 and UL subcell is determined b
No preference: A channel is assigned according to general channel assignment algorithms.System optimization
The level values 0 through 63 map to -110 dBm to -47 dBm. 0
Only when the receive level on the SDCCH is greater than or equal to Assign-optimum-level
63 Threshold and the TA is lower
If TA Pref. of Imme-Assign Allowed is set to Yes and the access_delay in the channel request
no message is lower than TA Th
If TA Pref. of Imme-Assign Allowed is set to Yes and the access_delay in
Underlaid Subcell: A channel in the UL subcell is preferentially assigned. the channel 60
Underlaid subcell
No Preference: A channel is assigned according to general channel assignment algorithms
No Preference: A channel is assigned according to general channel assignment algorithms. Underlaid subcell
The level values 0 through 63 map to -110 dBm to -47 dBm. 20
The level values 0 through 63 map to -110 dBm to -47 dBm. 35
When this parameter is set to No, the traffic load in the UL subcell is not taken into account
no for triggering the UL subcell to
3
20
70
80
VDF value comments
depend on the
configurations
and existing
values

depend on the Adjust the cell coverage area by configuring the Power Level; however, when the antenna is over high a
configurations
and existing Generally, for cells of the same priority in a network, the power level configuration should ensure that the
values
When configuring the power level, you should note that different TRXs in a cell can have different losses

Double Timeslot Extension Cell


Concentric Cell
on
yes
yes
yes
yes
yes
yes
0(invalid)
0(invalid)
60
63
3
System optimization
35
63(63 let this par need adjust according to actual coverage of overlayer
no
60(invalid)
System
Optimization If handover success rate is low, adjust to underlaid subcell.
Underlaid subcell
20
35
yes
3
20
70
80
en the antenna is over high and covers too many cells, you should lower the antenna and increase the tilt of the antenna first. When the

uration should ensure that the EIRPs of the cells are basically the same.

cell can have different losses due to different combination modes.


tilt of the antenna first. When the transmit power of a BTS reduces, the indoor coverage becomes worse.

Vous aimerez peut-être aussi